TomTom ONE Manuale utente

TomTom ONE/XL

Installation1.

2

Installation

1

4

2

3

5

+

6

8

2 SEC

3

1 2

7

4

1

180°

2

5

3

4

What’s in the box2.

5

What’s in the box

* Not included with all products.

aYour

TomTom ONE/XL

bEasyPort

TM

holder

cCar charger dRDS-TMC Traffic

Receiver*

eDocumentation

pack

fUSB cable

Before you start3.

6

Before you start

Switching on and off

Install your TomTom ONE/XL navigation device in your car following the

instructions in the installation section at the start of this book.

To switch on your navigation device, press and hold the On/Off button until

you see the start-up screen. The first time you switch on your device, it may

take a short time to start.

To set up your device you need to answer a few questions by tapping the

screen.

Device not starting

In rare cases, your TomTom ONE/XL navigation device may not start correctly

or may stop responding to your taps.

First, check that the battery is properly charged. To charge the battery,

connect your device to the car charger. It can take up to 2 hours to fully charge

the battery.

If this does not solve the problem, you can reset the device. To do this, press

and hold the On/Off button for fifteen seconds and release the button when

your device begins to restart.

Charging your TomTom ONE/XL

Before you use your ONE/XL for the first time, it’s a good idea to charge it fully

using the home charger, which takes about 2 hours.

There is no charging light on your ONE/XL. To check the battery status and see

when your ONE/XL is charging, switch on your device and tap the bottom

right-hand corner of the screen in the Driving View. The battery status is

shown on the next page.

Battery notes

The battery in your TomTom ONE/XL navigation device charges when you

connect it to the car charger or to your computer.

When you connect your device to a computer, you are asked if you want to

connect to the computer. If you select No and then do not tap the screen

within three minutes, the device will automatically switch off. This happens so

that the battery can charge faster.

Note: You should plug the USB connector directly into a USB port on your

computer and not into a USB hub or USB port on a keyboard or monitor.

7

GPS reception

When you first start your TomTom ONE/XL navigation device, the device may

need a few minutes to determine your GPS position and show your current

position on the map. In future, your position will be found much faster, usually

within a few seconds.

To ensure reception of a strong GPS signal, you should use your device

outdoors. Large objects such as tall buildings can sometimes interfere with

reception.

Take care of your device

Never leave your TomTom ONE/XL navigation device or accessories on view

when you leave the car or they may become an easy target for thieves.

You can set a password for your device which must be entered every time you

start it.

It is important to take care of your device.

• Your device is not designed for use in extreme temperatures and any such

exposure may cause permanent damage.

• Do not open the casing of your device under any circumstances. Doing so

may be dangerous and will invalidate the warranty.

• Wipe or dry the screen of your device using a soft cloth. Do not use any

liquid cleaners.

Safety4.

8

Safety

Positioning the dock

Consider carefully where to attach the dock in your car. The dock should not

block or interfere in any way with the following:

• Your view of the road

• Any of the controls in your car

• Any of your mirrors

• The airbag

You should be able to reach your navigation device easily when it is in the

dock without leaning or stretching. The diagrams show where you can safely

attach the dock.

You can attach the dock to the windscreen, side window or use a Dashboard

Mount Disk to attach the dock to your dashboard. TomTom also offers

alternative mounting solutions for your TomTom navigation device. For more

information about Dashboard Mount Disks and alternative mounting

solutions, go to www.tomtom.com/accessories.

Installing the dock

Make sure that both the holder and your window are clean and dry.

1. Press the suction cup firmly against the window on an area where the glass

is flat.

2. Twist the base of the EasyPort holder in a clockwise direction to lock the

holder in place.

For detailed instructions, check the installation section at the start of this

manual.

9

Safety preferences

We recommend using the safety preferences to make your driving as safe as

possible. The safety preferences include, for example, the following options:

• Hide most menu options when driving

• Show safety reminders

• Warn when driving faster than allowed

Making your first journey5.

10

Making your first journey

Planning a route with your TomTom ONE/XL navigation device is easy. To

plan a route, follow the steps below.

Important: For safety reasons, you should always plan a route before you

start your journey.

1. Tap the screen to bring up the Main Menu.

Note: The buttons on your navigation device are shown in full colour unless

a button is currently unavailable. For example, the button named Find

alternative in the Main Menu is not available until you have planned a route.

2. Tap Navigate to...

3. Tap Address.

When you enter an address, you can choose from the following options:

• City centre - tap this button to set your destination as the centre of a city

or town.

• Street and house number - tap this button to set an exact address as your

destination.

• Postcode - tap this button to enter a postcode as your destination.

Note: You can enter a postcode for any country. In the UK and the

Netherlands, postcodes are detailed enough to identify a house on their own.

11

In other countries you can enter a postcode to identify a town or area. You will

then have to enter a street and house number.

• Crossing or intersection - tap this button to set your destination as the

point where two streets meet.

• Spoken address - tap this button to set your destination by saying the

address to your navigation device.

In this example, we will enter an exact address.

4. Tap Street and house number.

Note: When planning a trip for the first time your navigation device asks you

to choose a state or country. Your choice is saved and used for all routes you

plan.

You can change this setting at any time by tapping the flag.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are

shown. When your destination appears in the list, tap the name of the town

to set the destination.

6. Start to type the street name and tap on the street when it appears in the list.

As with the name of the town, the names of the streets that match what you

have typed are shown. When your destination appears in the list, tap the

name of the street to set the destination.

7. Enter the house number and then tap Done.

12

8. Your navigation device asks if you need to arrive at a particular time. For this

exercise, tap NO.

The route is calculated by your device using IQ Routes

TM

.

IQ Routes is used to plan the best possible route taking into account the real

average speeds measured on the roads.

9. When the route has been calculated, tap Done.

Your TomTom ONE/XL navigation device will immediately begin to guide you

to your destination, using both spoken instructions and on-screen directions.

Arrival times

When you plan a route, your TomTom ONE/XL asks you if you need to arrive

at a particular time.

Tap YES to enter a preferred arrival time.

Your ONE/XL calculates your arrival time and shows you whether you will

arrive on time.

You can also use this information to work out when you need to leave. If your

ONE/XL shows that you will arrive 30 minutes early, you can wait and leave in

30 minutes time, rather than arrive early.

Your arrival time is constantly recalculated during your journey. The status bar

shows whether you will arrive on time or if you are going to be late, as shown

below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before

the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the

time you entered, it is shown in yellow.

13

Other navigation options

When you tap Navigate to..., you can set your destination in many ways, not

just by entering the address. The other options are listed below:

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered,

it is shown in red.

Status bar

preferences

Tap Status bar preferences in the Preferences menu, to enable or disable

arrival time notifications.

Select the required options on the first menu screen and then tap Done.

To enable arrival time notifications, select Show leeway to arrival time.

Home

Tap this button to navigate to your Home location.

You will probably use this button more than any other.

Favourite

Tap this button to select a Favourite as your destination.

Address

Tap this button to enter an address as your destination.

Recent

destination

Tap this button to select your destination from a list of places you have

recently used as destinations.

Point of

Interest

Tap this button to navigate to a Point of Interest (POI).

Point on map

Tap this button to select a point on the map as your destination using the

map browser.

Latitude

Longitude

Tap this button to enter a destination using latitude and longitude values.

14

Planning a route in advance

You can use your ONE/XL to plan a route in advance, selecting your starting

point and your destination.

Here are some more reasons to plan a route in advance:

• Find out how long a journey is going to take before you start.

You can also compare journey times for the same route at different times of

the day or on different days of the week. Your TomTom ONE/XL uses IQ

Routes when planning a route. IQ Routes calculates routes based on the real

average speeds measured on roads.

• Study the route of a journey you are planning.

• Check a route for someone who is coming to visit you and then explain the

route to them in detail.

To plan a route in advance, follow these steps:

1. Tap the screen to bring up the main menu.

2. Tap the arrow button to move to the next menu screen and tap Prepare

route.

3. Select the starting point for your journey in the same way that you would

select your destination.

4. Set the destination for your journey.

5. Choose the type of route that should be planned.

• Fastest route - the route which takes the least time.

• Shortest route - the shortest distance between the locations you set. This

may not be the quickest route, especially if the shortest route is through

a town or city.

• Avoid motorways - a route which avoids motorways.

• Walking route - a route designed for making the journey on foot.

• Bicycle route - a route designed for making the journey on a bicycle.

• Limited speed - a route for a vehicle which can only be driven at a limited

speed. You have to specify the maximum speed.

6. Choose when you will make the journey you are planning. There are three

options:

• Now

• Specific date and time - you will be asked to enter the date and time.

• No specific date and time

If you select either Now or Specific date and time, your ONE/XL uses IQ

Routes to work out the best possible route at that time, using the real

average speeds measured on roads. In this way you can compare how long

a journey takes at different times of day, or on different days of the week.

Position of

last stop

Tap this button to select your last recorded position, as your destination.

Prepare route

15

7. Your TomTom ONE/XL plans the route between the two locations you

selected.

More information about a route

You can access these options for the route you last planned by tapping the

Details button on the route summary screen.

You can then select from the following options:

Browse as

text

Tap this button for a list of all the turn instructions on the route.

This is very useful if you need to explain a route to someone else.

Browse as

images

Tap this button to see each turn in the journey. Tap the right and left arrows

to move forwards and backwards through the journey.

Tap the screen to turn off the 3D display and view the map from above.

Browse map

of route

Tap this button to see an overview of the route using the map browser.

Show route

demo

Tap this button to watch a demo of the journey. You can interrupt the demo

at any time by tapping the screen.

Show route

summary

Tap this button to open the route summary screen.

View route

Tap this button to see your route.

Driving View6.

16

Driving View

When your TomTom ONE/XL starts, you are shown the Driving View along

with detailed information about your current location.

Tap the centre of the screen at any time to open the Main Menu.

Note: The Driving View is shown in black and white until your ONE/XL locates

your current position.

ATap + and - to zoom in and out.

BQuick menu - switch this on in the Preferences menu.

CYour current position.

DThe name of the next major road or road sign information, if applicable.

ETraffic bar - requires an RDS-TMC Traffic Receiver (available as an

accessory).

FNavigation instruction for the road ahead.

Tap this area to repeat the last spoken instruction and to change the

volume.

GThe name of the street you are on.

HInformation about your journey such as journey time, remaining distance

and arrival time.

To change the information shown, tap Status bar preferences in the

Preferences menu.

IGPS signal strength.

Advanced Lane Guidance7.

17

Advanced Lane Guidance

Your TomTom ONE/XL helps you prepare for motorway exits and junctions by

showing you which lane you should be in.

Note: This information is not available for all junctions or in all countries.

For some exits and junctions, an image shows the turn and the lane you

should take.

To turn the images off, tap Hide lane images in the Preferences menu.

For other exits and junctions, your ONE/XL shows the lane you should take in

the Status bar. To turn this guidance off, tap Change preferences in the Main

Menu, then tap Status bar preferences. Clear the checkbox for Show lane

guidance.

Finding alternative routes8.

18

Finding alternative routes

Once you have planned a route, you may want to change something about the

route, without changing your destination.

Why change the route?

Maybe for one of these reasons:

• You can see a roadblock or a line of traffic ahead.

• You want to travel via a particular location, to pick someone up, stop for

lunch or fill up with petrol.

• You want to avoid a difficult junction or a road you don’t like.

Find alterna-

tive...

Tap Find alternative... in the Main Menu to change the route that is

currently planned.

The Find alternative... button is also shown in the route summary screen

after you plan a route.

Calculate

alternative

Tap this button to calculate an alternative to the route already planned.

Your ONE/XL will look for another route from your current location to your

destination.

If you decide you would prefer to use the original route after all, tap

Recalculate original.

Why would I need to do this?

Apart from the roads near your position and near your destination, the new

route will use totally different roads to reach your destination. This is an

easy way of calculating a totally different route.

Avoid

roadblock

Tap this button if you can see a roadblock or a line of traffic ahead. You then

have to choose how much of the route ahead you want to avoid.

Choose from the different options: 100m, 500m, 2000m, 5000m. Your ONE/

XL will recalculate your route avoiding the section of the route for the

distance you selected.

Don’t forget that once a new route is calculated, you may have to turn off

the road you are on very soon.

If the roadblock suddenly clears, tap Recalculate original to return to your

original route.

19

Travel via...

Tap this button to change your route so that it passes a particular location,

perhaps to pick someone up on the way. When you do this, a marker is

shown on the map for the location you choose the travel via.

You choose the location you want to pass in the same way as you choose a

destination. So you can select from all the same options: for example,

Address, Favourite, Point of Interest and Point on map.

Your ONE/XL will calculate a new route to your destination that passes the

location you chose. Unlike your final destination, your ONE/XL does not

inform you when you pass by this location.

Using this button, you can only travel via one location. If you want to pass

more than one, use an Itinerary.

Recalculate

original

Tap this button to return to the original route without deviations to avoid

roadblocks or travelling via particular locations.

Avoid part of

route

Tap this button to avoid a part of the route. Use this button if you see that

your route includes a road or junction you don’t like, or which is well-

known for traffic problems.

You then choose the road you want to avoid from a list of the roads on your

route.

Browse Map9.

20

Browse Map

To look at the map in the same way as you might look at a traditional paper

map, tap Browse map in the Main Menu.

You can move the map by touching the screen and moving your finger across

the screen.

AThe scale bar

BGPS button

Tap this button to centre the map on your current position.

COptions

DThe cursor

EThe Find button

Tap this button to find specific addresses.

FThe Cursor button

Tap this button to navigate to the cursor position, make a Favourite of the

cursor position, or find a Point of Interest near the cursor position.

GThe zoom bar

Zoom in and out by moving the slider.

Options

Tap the Options button to set the information shown on the map. You can

choose to show the following information:

• Points of interest. Tap POI below the list of options to select which POIs are

shown.

La pagina sta caricando ...

TomTom ONE Manuale utente

TomTom ONE Manuale utente

in altre lingue

Documenti correlati

Altri documenti