Philips 32PW9509/05 Manuale utente

Marca: Philips

Modello: 32PW9509/05

Categoria: TV LCD

Tipo: Manuale utente

cover 2285.1 eur 21-01-2004 08:40 Pagina 1

cover 2285.1 eur 21-01-2004 08:40 Pagina 2

Information for users in the UK

(Not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some

distance away from radiators or other sources of heat. Leave a space of at least 5 cm all around

the TV for ventilation, making sure that curtains, cupboards etc. cannot obstruct the air flow

through the ventilation apertures.

The TV is intended for use in a domestic environment only and should never be operated or

stored in excessively hot or humid atmospheres.

General Points

Please take note of the section 'Tips' at the end of this booklet.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help

TV license holders improve reception of BBC and IBA programmes where they are being spoilt by

interference.

If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television

and Radio Reception".

Mains connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the

voltage printed on the type plate on the rear panel of the TV. If the mains voltage is different,

consult your dealer.

Important

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows :

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

In order to maintain conformity to the EMC directive, the mains plug on this product must not be

removed.

Connecting the aerial

The aerial should be connected to the socket marked x at the back of the set. An inferior aerial is

likely to result in a poor, perhaps unstable picture with ghost images and lack of contrast. Make-

shift or set-top aerials are unlikely to give adequate results.

Your dealer will know from experience the most suitable type for your locality.

Should you wish to use the set in conjunction with other equipment, which connects to the aerial

socket such as TV games, or a video camera, it is recommended that you consult your dealer on

the best method of connection.

Stand (if provided)

Use only the stand provided with the set, making sure that the fixings are properly tightened.A

diagram showing how to assemble the stand is packed with the stand. Never use a make-shift

stand, or legs fixed with woodscrews.

2288.1 en 21-01-2004 08:37 Pagina 1

2288.1 en 21-01-2004 08:37 Pagina 2

Contents

Preparation ........................................................................................ 2

Keys on top of the TV .................................................................... 2

Your remote control ................................................................... 3-4

To use the menus.............................................................................. 5

Select the menu language and country ....................................... 5

Store TV channels ............................................................................ 6

Automatic installation ..............................................................6

Manual installation .................................................................... 6

Give name .................................................................................. 6

Reshuffle the programme list.................................................. 7

Select favourite TV channels .................................................. 7

TV setup ............................................................................................. 7

General ....................................................................................... 7

Source .......................................................................................... 8

Decoder ...................................................................................... 8

Demo .................................................................................................. 8

Installation

TV menu

Picture menu ........................................................................ 9-10

Sound menu ............................................................................. 10

Features menu......................................................................... 11

Teletext guide ................................................................................. 12

Teletext ...................................................................................... 13-14

Connect peripheral equipment

Connecting and selecting equipment ..................................15-16

Audio- and video equipment keys ............................................. 17

Tips .................................................................................................. 18

Operation

EasyLink features are based on the “one touch operation” approach.

This means that a sequence of actions are executed at the same time

in both the television and the video cassette recorder, provided both

are fitted with the EasyLink function and connected with the eurocable

supplied with your video recorder.

R End of life directives

Philips is paying a lot of attention to

producing environmentally-friendly in

green focal areas.Your new TV contains

materials which can be recycled and

reused. At the end of its life specialised

companies can dismantle the

discarded TV to concentrate the

reusable materials and to minimise the

amount of materials to be disposed of.

Please ensure you dispose of your old

TV according to local regulations.

Help?

If this instruction manual does

not give an answer or if ‘Tips’ do

not solve your TV problem, you

can call your Local Philips

Customer or Service Centre. See

the supplied World-wide

guarantee booklet.

Please, have the Model and

Product number which you can

find at the back of your television

set or on the packaging, ready,

before calling the Philips helpline.

Model: 28-32PW9509

Product No: ..............................................

Due to continuous product

improvements this manual is subject

to change without notice.

English

2288.1 en 21-01-2004 08:37 Pagina 1

& Place the TV on a solid surface.

! 28PW9509: 37 kg; 32PW9509: 56 kg !

For ventilation, leave at least 5 cm free all

around the TV. Do not place the TV on a

carpet.To prevent any unsafe situations, do not

place any objects on top of the TV. Avoid heat,

direct sunlight and exposure to rain or water.

é Insert the aerial plug firmly into the aerial

socket x at the back of the TV. For best

picture quality use the suppressor-aerial cable

supplied.

“ Insert the mains plug of the TV in the wall

socket having a mains voltage of 220V-240V.

‘ Remote control: Insert the 2 batteries

supplied (Type R6-1,5V).

The batteries supplied do not contain the heavy

metals mercury and cadmium. Please check on how

to dispose of exhausted batteries according to local

regulations.

( Switch the TV on : Press the power switch A

on the front of your TV.

A blue indicator on the front of the TV lights

up and the screen comes on. If the TV is in

standby mode (red indicator), press the

-P+

keys or the red B key on the remote control.

Preparation

min.

Should your remote be lost or broken you can still

change some of the basic settings with the keys on

top of your TV.

Press:

• the

VOLUME - or + key to adjust the volume;

• the PROGRAM - or + key to select the TV

channels or sources.

Press the

MENU key to summon the main menu

without the remote control.

Use:

• the

VOLUME - or + key and the PROGRAM -

or + key to select menu items in the directions

as shown;

• the

MENU key to confirm your selection.

Note:

When activated via the

MENU key on top of the TV,

only

Exit lets you dismiss the menu.

Navigate to

Exit and press the MENU key.

Keys on top of the TV

Setup

Demo

Install

Exit

Picture Sound Features

MENU PROGRAMVOLUME

2288.1 en 21-01-2004 08:37 Pagina 2

Select

VCR DVD SAT AMP CD

123

456

789

‡π

†

Active Control

VCR DVD SAT AMP CD

Audio and Video equipment keys

(p. 17)

v Select peripherals

(p. 16)

Use of the remote control RC4301

Note: For most keys pressing a key once will activate the function. Pressing a second time will de-activate it.

When a key enables multiple options, a small list will be shown. Press repeatedly to select the next item in the list.

The list will be removed automatically after 4 seconds or press

OK to remove immediately.

B Standby

Press to switch the TV on or off.

When switched off, a red

indicator on the TV lights up.

®Ò‡π†

Audio- and Video equipment keys

(p. 17)

® Instant record

See Record with your recorder

with EasyLink, p. 17.

U Time display

The time is displayed on the

screen.

Q Surround mode

Incredible surround

With stereo transmission, and

when Incredible surround is

selected, it seems as though the

loudspeakers are spread further

apart from one another.

Virtual Dolby Surround

Optimal with Dolby surround

signals. Enables you to

experience the effect of Dolby

surround Pro Logic, reproducing

a rear sound effect. See Sound

menu, 3D effect, p. 10.

Note:You can make the same

selection in the Sound menu,

surround mode, p. 10.

Ì Cinema Go

See separate Cinema Link

booklet supplied.

æ Teletext Guide on/off p. 12

Press the

b key to show

Teletext Guide on the right half

of the screen.

S Freeze

To freeze the picture.

x Pixel Plus 2 demo on/off

In the right part Pixel Plus 2 and

Digital Natural Motion are

switched on.

b Teletext on/off p. 13

Press the

b key to show

teletext on the right half of the

screen.

OK Press this key

• to activate your choice, when in

the menus.

• to display the programme list.

MENU Main menu on/off see p. 5

V To adjust the volume.

¬ Interrupt the sound or restore it.

PProgramme selection

To browse through the TV

channels and sources stored in

the favourite list.

0/9 Digit keys

To select a TV channel.

For a two digit programme

number, enter the second digit

before the dash disappears.To

switch immediately to a selected

one digit TV channel, keep the

digit key pressed a bit longer.

2288.1 en 21-01-2004 08:37 Pagina 3

i On Screen information

Press to display information about the selected TV channel and

programme.

Menu/Remote control info

When a menu is on screen, press i to display info on the selected

menu item. For information on the remote control functions, while the

menu info is displayed, press any key on the remote control.

The normal function of the key is not executed.

0 Smart surf

With this key you can easily switch between 2 up to 9 different TV

channels or sources. See General, Smart surf, p. 7.

Press the

OK key or wait for the time out to dismiss the Smart surf

display.

b Dual screen

& Press the b or æ key.

Press the

b key to show Teletext or Teletext Guide on the right of the

screen.

é • Picture/Teletext Guide:

-Press the cursor left/right to select a TV channel.

-Press the cursor down to move the puck to the blue ball in the left

screen.

-Press

+P- to select another TV channel.

• Picture/Teletext:

See Active screen selection, p. 13.

“ Press the b key to switch off dual screen.

h Active control see p. 10

q Picture format

Press this key repeatedly or press the cursor up/down to select another

picture format:Auto format, Super zoom, 4:3, Movie Expand 14:9, Movie

Expand 16:9, Subtitle zoom or Wide screen.

Auto format makes the picture fill the screen as much as possible.

In case of subtitles in the bottom black bar, Auto format makes the

subtitles visible. If subtitles are only partly visible, press cursor up.

In case of a broadcaster logo in the corner of the top black bar, the logo

disappears from the screen.

Super zoom removes the black bars on the sides of 4:3 programs with

minimal distortion.

When in Movie Expand 14:9, 16:9, Super zoom or Subtitle zoom picture

format, you can make subtitles visible with the cursor up/down.

Auto format Super zoom 4:3 Movie Expand 14:9

Movie Expand 16:9 Subtitle zoom Wide screen

Select

VCR DVD SAT AMP CD

123

456

789

‡π

†

Active Control

2288.1 en 21-01-2004 08:37 Pagina 4

To use the menus

& Press the MENU key on the remote control to summon the

main menu.At any moment you can exit the menu by

pressing the

MENU key again.

Note: If you have connected equipment with Cinema Link, more

menu items are present.

é Use the cursor in the up/down direction to select the TV,

Setup, Demo or Install menu.

Use the cursor left/right to select

Picture, Sound or

Features.

Note: Sometimes not all the menu items are visible on the screen

(indicated by a cluster of blue balls). Use the cursor down or right

to reveal all items.

“ Use the cursor in the left/right direction to select the menu

item.

‘ Use the cursor up/down again to select the control you

want to select or to adjust.

Note: Items temporary not available or not relevant are displayed

in a light grey colour and cannot be selected.

Setup

Demo

Install

Picture Sound Features

Installation

& Press the MENU key on the remote control.

é Use the cursor down to select Install.

“ Use the cursor right to select Language.

Follow the instructions on screen.

‘ Use the cursor up/down to select your preferred language

and press the

OK key to confirm your selection.

( Use the cursor right to select Country.

§ Select the country where you are now located and press

the

OK key.

Select

Other when none of the countries applies.

è Proceed with the Install menu.

Install

Language Country Automatic Manual Give name Reshuffle Favourite

install install programmes

The installation menu contains the following items:

EasyLink

If your video recorder has an EasyLink function, during installation, the language, country and available channels

are automatically transmitted to the video recorder.

Language

English

Deutsch

Français

Install

Country

Austria

Belgium

Croatia

Install

Select the menu language and country

Select

VCR DVD SAT AMP CD

‡π

†

cursor to select

adjustments

OK key to

activate

return or switch

main menu on/off

Press the i key on the

remote control to get

information about the

selected menu item.

2288.1 en 21-01-2004 08:37 Pagina 5

& Select Automatic install in the Install menu.

Note: All channels must be unlocked in order to

autoprogram. If requested, enter your code to unlock

all channels. (See TV, Features menu, Childlock,

p. 11.)

é Press the cursor down.The autoprogramming

option label

Start appears.

“ Press the cursor right.

‘ The message Searching appears and the

progress of autoprogramming is displayed.

If a cable system or a TV channel which

broadcasts ACI (Automatic Channel

Installation) is detected, a programme list

appears.Without ACI broadcast, the channels

are numbered according your language and

country selection.You can use Reshuffle to

renumber them. See p. 7.

It is possible that the cable company or the TV

channel displays a broadcast selection menu.

Layout and items are defined by the cable

company or the TV channel. Make your choice with

the cursor and press the

OK key.

After language and country are set correctly, you can now search for and store the TV channels in two

different ways: using Automatic Installation or Manual Installation (tuning-in channel by channel).

Select your choice with the cursor right.

Manual installation

Automatic installation

Searching for and storing TV channels is done channel by channel.

You must go through every step of the Manual Installation menu.

& Select Manual install in the Install menu.

é Press the cursor down.

Follow the instructions on screen.

Note: Search or direct selection of a TV channel.

If you know the frequency, the C- or S-channel number, enter the 3 or

2 digits of the frequency or the channel number directly with the digit

keys 0 to 9 (e.g. 048). Press the cursor down to proceed.

Repeat to search for another TV channel.

It is possible to change the name stored in the

memory or to assign a name to a TV channel for

which a name has not yet been entered.A name

with up to 5 letters or numbers can be given to

the programme numbers 0 to 99.

& Select Give Name in the Install menu and

press the cursor down.

é Select the programme number.

Note: keep the cursor up/down pressed to scroll

through the programme list quickly.

“ Press the cursor right.

A keyboard appears on the screen.

Press the cursor right to enter the keyboard.

Press the cursor up/down, left/right to select

the first character and press

OK. Repeat for

every character you want to enter.

Select

Space to enter a space; Delete to erase

the highlighted character in the name entered;

Shift to display upper- or lowercase characters

on the keyboard;

Special to display special

characters on the keyboard. Press

OK to

confirm.

‘ Press the cursor left repeatedly when you have

finished the name giving.

( Select another programme number and repeat

steps

“ to ‘.

Give name

pπ

® Space ® Delete

ABCDEFG 123

HIJKLMN 456

OPQRSTU 789

VWXYZ 0

® Shift ® Special

Give name

Install

VCR1

BBC1

BBC2

CNN

TVE

.....

Automatic install

Install Start

Install

Manual install

Install

Selection mode

System

Programme

Fine tune

Store

Store TV channels

2288.1 en 21-01-2004 08:37 Pagina 6

Reshuffle the programme list

You can change the order of the stored TV

channels.

& Select Reshuffle in the Installation menu.

é Follow the instructions on screen.

Select Favourite TV channels

& Select Favourite programmes in the Install

menu.

é Select your programme number with the

cursor up/down.

“ Select Ye s or No with the cursor right.

‘ Repeat é and “ for every TV channel or

external you want to make a favourite or a

non-favourite TV channel or external.

TV Setup

The Setup menu contains items that control the settings of the

TV’s functions, features, services and peripherals you may have

connected.

The

General menu allows you to change various settings that

are presumably adjusted less frequently than most other

settings.

The

Source menu allows you to select a source.

The

Decoder menu allows you to define one or more

programme numbers as decoder programme numbers.

Press the i key on the remote control to get information

about the selected menu item.

General Source Decoder

Menu background

Smart surf

Factory settings

Tilt adjust

OSD

Programme title

Teletext level 2.5

Auto surround

Set/Change code

Setup

Smart surf

& Select Smart surf.

é With the cursor left/right, select

•

2 programmes if you want the 0 key to

toggle between the current and the previously

selected channel,

•

9 programmes if you want the 0 key to

summon a list of up to 9 channels which can

be selected,

To add/remove a channel or source:

Tune to the channel or source you wish to add

or remove. Press the 0 key and press the

cursor right to add or remove.

Note: If there are already 9 channels/sources in the

list, the one at the bottom of the list will be

removed.

Factory settings

This resets the picture and sound settings to

their predefined factory values, but maintains

the channel installation settings.

OSD (On Screen Display)

See Use of the remote control, p. 3, i On

screen information.

& Select OSD.

é Select Normal to activate the continuous

display of the programme number.Also TV

channel and programme information are

extended.

Minimum will display reduced

channel information.

Note: When subtitles is switched on, see Features,

p.11, continuous display of the programme number

is not possible.

Teletext 2.5

Some broadcasters offer the opportunity to

see more colours, other background colours

and nicer pictures in the teletext pages.

& Select Teletext 2.5.

é Press the cursor right to select Teletext 2.5

to take advantage of this feature.

“ Press the cursor right again to select Teletext

2.5 Off

if you like the more neutral teletext

layout.

The selection made is valid for all channels

which broadcast teletext 2.5.

Note: It may take a few seconds before teletext

broadcast switches over to Teletext 2.5.

General

2288.1 en 21-01-2004 08:37 Pagina 7

Source

This menu allows you to indicate the peripheral

you connected to one of the external inputs.

& Press the cursor right to enter the list of types

of peripherals attached to the selected input.

é Select the peripheral device with the cursor

up/down.

Once you have selected the source type, e.g. DVD,

this source will automatically be selected when

your remote control is in DVD mode, see p. 3, and

when you press the v key on the remote

control.

Auto Surround

Sometimes the broadcaster transmits special

signals for Surround Sound encoded

programmes.The TV automatically switches to

the best surround sound mode when

Auto

Surround

is switched On.

Set/Change code

The Child lock feature (see TV, Features, p. 11)

allows you to lock channels to prevent others

from watching certain programmes.To watch

locked channels, a 4-digit code must be

entered.The Set/Change code menu item

allows you to create or change a Personal

Identification Number (PIN).

& Select Set/Change code.

é If no code exists yet, the menu item is set to

Set code. If a code has previously been entered,

the menu item is set to

Change code.Follow

the instructions on screen.

Important:You have forgotten your code !

& Select Change code in the General menu and

press

OK.

é Press the cursor right and enter the overriding

code 8-8-8-8.

“ Press the cursor again and enter a new

personal 4-digit code.The previous code is

erased and the new code is stored.

If a decoder or a descrambler is connected, see

p. 15, you can define one or more programme

numbers as decoder programme numbers.

& Select Decoder with the cursor right.

é Select Programme.

“ Select the programme number under which

you have stored the programme coming from

your decoder.

‘ Select Status.

• Select the input used to connect your

decoder:

None, EXT1 or EXT2.

• Select

None if you do not want the selected

programme number being activated as a

decoder programme number.

Note: Select

EXT2 when the decoder is connected

to your EasyLink video recorder.

Decoder

Programme

Status

Setup

Source

EXT1

EXT2

EXT3

SIDE

Setup

2288.1 en 21-01-2004 08:37 Pagina 8

& Press the cursor right to select Picture.

é Select the menu items in the Picture menu with

the cursor up/down.

“ Adjust the settings with the cursor left/right or

enter the list of submenu items with the cursor

right. Select a submenu item with the cursor

up/down.

Note:To remove the menu background before

adjusting the picture settings, see Select TV setup,

General, p. 7.

Smart picture

Select

Smart picture to display a list of

predefined picture settings, each corresponding

with specific factory settings.

Personal refers to the personal preference

settings of picture in the picture menu.

Digital options

Pixel Plus 2 is the most ideal setting, doubles

the horizontal resolution and increases the

number of lines with 33%.You may consider to

select Movie Plus in case a halo effect should

disturb you. Dependent on your own

preference, select Double lines, or 100 Hz

Digital Scan.

Note: When 60 Hz NTSC material is used, the

options are changed to Pixel Plus 2, Movie Plus or

Progressive, progressive scan without motion

compensation.

TV menu

Press the MENU key on the remote control to summon the main menu.

Press the i key on the remote control to get information about the selected menu item.

Picture Sound Features

Smart picture

Contrast

Brightness

Colour

Sharpness

Tint

Digital options

Dynamic contrast

DNR

Colour enhancement

(Hue)

Picture format

Picture menu

Demo

The Demo menu allows to demonstrate the TV

features separately or in a continuous loop.

Auto demo has been selected the demo will

automatically present the features sequentially in a

loop. Press one of the cursor keys to stop the

Auto demo.

If one of the features has been selected, this

particular feature demo will run only once, and the

Demo menu will reappear.

Note:The Dealer demo is not part of the automatic

sequence and can only be activated separately.

Auto demo

......

Dealer demo - Digital options

- Light sensor

- Comb filter

Setup

Demo

Install

2288.1 en 21-01-2004 08:37 Pagina 9

& Press the cursor right to select Sound.

é Select the menu items in the Sound menu with the cursor

up/down and adjust the settings with the cursor left/right.

Remember, control settings are at normal mid-range levels when

the bar scale is centred.

Smart sound

Select

Smart sound to display a list of predefined sound

settings, each corresponding with specific factory settings of

Treble and Bass.

Personal refers to the personal preference settings of sound in

the sound menu.

Notes:

- Some menu items are only available in case of a Cinema Link

configuration and when the Cinema Link is activated. Others are

steered by the audio receiver instead of by the TV. See the separate

Cinema Link booklet supplied.

Dual X is only available with dual sound transmission.

Mono/Stereo is only selectable in case of analogue stereo

transmission.

Nicam/Analogue is only selectable in case of Nicam transmission.

Sound

Smart sound

Equalizer

Volume

Balance

(Loudness)

Headphone volume

Surround mode

(Dual I-II)

(Mono/Stereo)

(Nicam/Analogue)

(3D effect)

AVL

Delta volume

Sound menu

Active Control

The TV continuously measures and corrects all incoming signals in

order to provide the best picture possible.

& Press the h key on the remote control.

é The Active Control menu appears.

“ Press the cursor up/down to select the Active Control values

Off, Minimum, Medium (recommended) or Maximum.

The picture settings are being optimised continuously and

automatically which is displayed by bars.The menu items can

not be selected.

‘ Press the cursor right to select Smart Picture.

( Press the cursor up/down to select one of the predefined

picture settings.

§ Press the cursor right to select Active Display.

è Press the cursor up/down to select Show bars, one of the Dual

screen demos or

Off.

When you select Dynamic contrast, Pixel Plus 2, Digital Noise

Reduction or Digital Natural Motion, the TV screen is divided

into two parts: in the left part the selected picture quality

setting is switched off; in the right part it is switched on.

! Press the h key again to switch off the Active Control menu.

2288.1 en 21-01-2004 08:37 Pagina 10

Programme list

Press the

OK key to switch over to the

selected TV channel or external.

Select subtitles

The subtitle page must be stored for each TV

channel:

Switch on teletext and select the proper

subtitle page from the index. Switch off teletext.

Subtitle On will automatically display them on

the selected TV channels if subtitles are in the

transmission.A symbol will indicate that the

mode is on.

Select

On during mute when you want to

have the subtitles automatically displayed only

when the sound has been muted with the ¬

key on the remote control.

Child lock

& Select Child lock.

é Press the cursor right to enter the Child lock

menu.You’re summoned to enter your code.

Note:You have to re-enter your code each time you

enter the child lock menu.

Important:You have forgotten your code !

See p. 8.

“ Select one of the menu items of the child lock

menu:

•

Lock if you want to lock all channels and

externals.

•

Custom lock and press the cursor right.

Select:

Lock after if you want to lock all channels

and externals from a certain time onwards.

Press the cursor right and enter the time

with the cursor up/down and right. Press the

OK key to validate.

Programme lock if you want to lock a

certain TV channel or external;

• Select

Unlock to disable all locks you have

set.

On timer

& Select On timer with the cursor down.

é Select On with the cursor right.

“ Press the cursor right again to enter the

programme list.

‘ Select the TV channel or external you want

your TV to switch to on a selected time and

day.

( Press the cursor right again to select a day of

the week or to select

Daily.

§ Press the cursor right once again to enter the

time with the digit keys or with the cursor

up/down and press the

OK key to activate.

è Press the MENU key to turn off the menu.

Note:To check your timer settings, press the i key.

Zoom

& Select Zoom with the cursor down and press

the

OK key.

é Press the OK key to select one of the zoom

magnifications (x1, x4, x9, x16).

“ Additionally you can shift the selected zoom

window over the screen with the cursor keys

up/down, left/right.

‘ Press the MENU key to turn off the zoom

function.

Child lock

Lock

Custom lock

Unlock

Lock after

Programme lock

Features menu

Features

Programme list

Subtitle

Sleeptimer

Child lock

On timer

Zoom

Off

On during mute

& Press the cursor right to select Features.

é Select the menu items with the cursor

up/down and adjust the settings with the

cursor left/right.

VCR1

BBC2

CNN

TVE

π.....

Sunday

Monday

.......

Daily

15:45

On timer

Off

2288.1 en 21-01-2004 08:37 Pagina 11

Teletext guide

& Press the æ key.

é Select a TV channel with the cursor up/down and press OK.

“ Move the cursor up to the top of the channel list where the name of the selected TV channel

reappears.

‘ Press the cursor right to move the puck over the selection ball.

( In the teletext index page, look for the programme guide page of the day or the following day.

§ Enter with the digit keys, the programme guide page number.

Press the cursor right twice to move the puck to the right to choose one of the subpages if available.

If the selected programme satisfies the VPT requirements, the TV will remember the last selected teletext

page number of that channel that contains programme guide information and indicates which programme

starts at what time.

Every time you press the æ key, the teletext programme guide page of the selected TV channel will be

available.

Note:The broadcaster is responsible for the content of the information.

Basic functions

Press one of the grey, red, green, yellow or blue keys to activate a Teletext Guide function. The keys

appear in grey if the function is not available.

Review: this menu provides a list of programmes that are marked as reminders, those that have to be

recorded and those that are locked.This menu can be used to change or remove marked

programmes.

Record: to programme the recording of the video recorder (if it has a NEXTVIEWLink function and is

connected to

EXT. 2).

Remind: to automatically switch on the TV if it is in standby or to display a message if the TV is on.

Lock: to lock certain programmes to prevent recording or watching.

For the functions Record, Remind or Lock, a small menu pops up in which you can choose the

interval: once, daily or weekly, or clear an earlier made record, remind or lock setting.The default

interval is set to

Once.To confirm the frequency, press the OK key.

Watch: to watch the selected and currently broadcast programme.

Review Record Remind Watch Lock

BBC1

BBC2

ITV

CH4

CH5

page ball

selection ball

channel list

Mon 05 Feb 16.35

100 1

BBC CEEFAX

LIONS RECORD ANOTHER WIN 430

Index 100 News 300

BBC Info 110 Headlines 305

Children 120 Weather 400

Cookery 150 Sports 415

Education 200 Radio 500

subpages

scroll ball

TV channels which broadcast teletext also transmit a page with the programme guide of the day.

If the displayed teletext programme guide page satisfies the Video Programming via Teletext (VPT)

requirements, it will be possible to record, remind, watch or lock programmes.

2288.1 en 21-01-2004 08:37 Pagina 12

Switch Teletext on and off

Press b to switch the teletext on.

Select a Teletext page

- Enter the desired page number with the digit

keys, the cursor keys up/down or with the -P+

key.

- Select the options at the bottom of the screen

with the colour keys.

Previously selected teletext page

(Only possible in case there is no list of favourite

teletext pages available. See p. 14.)

Press the 0 key.

Select the index teletext page

Press the grey colour key † to display the

main index (usually p.100).

Only for T.O.P teletext broadcasts:

Press i.A T.O.P. overview of the teletext

subjects available is displayed.

Select with the cursor up/down, left/right the

desired subject and press the

OK key.

Not all TV channels broadcast T.O.P. teletext.

Select subpages

When a selected teletext page consists of

different subpages, a list of available subpages

appears on the screen.

Press the cursor left or right to select the next

or previous subpage.

Enlarge a Teletext page

Press q repeatedly to display the upper

teletext part, the lower teletext part and then

to return to the normal teletext page size.

When the teletext page is enlarged, you can

scroll the text, line by line using the cursor

up/down.

Picture/Teletext

& Press the b key. Press the b key to show

Teletext on the right of the screen.

é Use the cursor keys to select a TV channel.

“ Press the b key to switch off dual screen.

Active screen selection

When in dual screen picture/teletext (b key),

enter the desired page number with the

-P+

key, then press the MENU key, then select the

left screen (with the blue ball at the top).

You can now select a compressed or full screen

view of picture/teletext with the q key.

Hypertext

With hypertext you can quickly jump to a

pagenumber or search for a specific word

shown on the current teletext page.

& Press the OK key to highlight the first word or

a number on the page.

é Use the cursor up/down, left/right to select any

other word or number you want to search for.

“ Press the OK key to confirm.The search starts.

A message appears at the bottom of the screen

to indicate the searching, or that the word or

page is not found.

‘ Use the cursor up to exit hypertext.

Teletext

Most TV channels broadcast information via teletext.This TV has a 1200 pages memory that will store

most broadcasted pages and subpages to reduce waiting time. After each programme change, the

memory is refreshed.

LIONS RECORD ANOTHER WIN 430

Index 100 News 300

BBC Info 110 Headlines 305

Children 120 Weather 400

Cookery 150 Sports 415

Education 200 Radio 500

Lottery 230 Travel 550

Finance 240 Subtitling 888

Music 280 TV Listings 600

Red Green Yellow Blue

102 W «03 04 05 06 07 08 09 10 11 12»

BBC CEEFAX 102 Mon 05 Feb 16.35.22

BBC CEEFAX

2288.1 en 21-01-2004 08:37 Pagina 13

Teletext menu

(only available in full screen teletext mode)

& Press the MENU key to activate the menu.

é Press the cursor up/down to select the menu

items.

“ Press the cursor right to activate.

Reveal

Reveals/conceals hidden information on a page,

such as solutions to riddles and puzzles.

Press the cursor right to activate.

Favourite

You may create a list of eight favourite teletext

pages in total, selected from various TV

channels.

To add a favourite page to the list:

& Select a favourite teletext page.

é Select Favourite in the teletext menu and

press the cursor right to enter the list.

" Press the cursor right again to add the page.

' Press the MENU key to watch the current

page.

To watch a favourite page from the list:

When in Teletext, use the 0 key to browse

through the favourite pages of the TV channel

actually selected.

Note: Only the pages of the current channel

can be selected.

Selecting a word

On the keyboard on screen you can type in a

random word you want to search for in the

teletext pages.Whether upper- or lowercase is

used has no influence.

& Press the cursor right to enter the keyboard.

é Press the cursor left/right, up/down to select

the characters, words or functions.

“ Press the OK key to confirm each character

selected.

‘ Select Cancel to cancel the word; Space to

enter a space;

Delete to delete the last

character selected;

Shift to switch between

lowercase or capital characters;

Special to

display special characters on the keyboard and

press the

OK key.

( Press the cursor left repeatedly to return to

the Teletext menu again.

Searching a word

& Type in the word on screen or select a word

from the history list on the right and press

OK.

é Select Accept and press OK again.The

message

Searching appears.

“ To cancel the searching or to search for a new

word, select

Keyboard and press OK.

‘ When a word is not found, a message appears.

When the word is found, it is highlighted in the

teletext page.To continue the search, press the

OK key.

Cycle subpages (if available)

Makes the subpages cycle automatically.

Press the cursor right to activate and to de-

activate again.

Timed page

To display a specific page from a selected TV

channel at a certain time.

& Press the cursor right and select Yes or No.

é Enter the time and pagenumber with the

cursor keys or the digit keys.

Note:Teletext does not have to remain switched on,

but you should watch the TV channel you have

selected the specific page from.

“ Press the cursor left to return to the TV menu

again.

Language

If the displayed characters on screen do not

correspond with the characters used by the

teletext broadcaster, you can change the

language group here.

Select

Group 1 or 2 with the cursor right.

Press the

MENU key to leave the Teletext

menu.

102 03 04 05 06 07 08 09 10 11 12

TELETEXT

BBC1

Red Green Yellow Blue

puck

Cancel Accept

Space Delete

ABCDEFG 1 2 3

HIJKLMN 4 5 6

OP QRSTU 7 8 9

V W X Y Z 0

Shift Special

WORD

NAME

FOOTBALL

2288.1 en 21-01-2004 08:37 Pagina 14

There is a wide range of audio and video equipment that can be connected to your TV.

The following connection diagrams show you how to connect them.

Note:

EXT. 1 can handle CVBS and RGB, EXT. 2 CVBS and Y/C, EXT. 3 CVBS and RGB. It is preferred to connect

peripherals with RGB output to

EXT. 1 or EXT. 3 as RGB provides a better picture quality.

If your recorder is provided with the Easylink function, it should be connected to

EXT. 2 to benefit from the EasyLink

functionality.

Recorder (VCR-

DVD+RW)

Connect the aerial cables 1, 2 and, to obtain the optimum

picture quality, eurocable 3 as shown.

If your recorder does not have a euroconnector, the only

possible connection is via the aerial cable.You will therefore

need to tune in your recorder’s test signal and assign it

programme number 0 or store the test signal under a

programme number between 90 and 99, see Manual installation,

p. 6. See the handbook of your recorder.

Decoder and Recorder

Connect a eurocable 4 to your decoder and to the special

euroconnector of your recorder. See also the recorder

handbook. See Decoder, p. 8. You can also connect your

decoder directly to

EXT. 1 or 2 with a eurocable.

Other equipment

(satellite receiver, decoder, DVD, games, etc.)

& Connect the aerial cables 1, 2 and 3 as shown (only if

your peripheral has TV aerial in-/output).

Connect your equipment with a eurocable 4 or 5 to one of

the euroconnectors

EXT.1, 2 or 3 to obtain a better picture

quality.

é Look for the test signal of your peripheral in the same way as

you do for a recorder.

“ Make a selection in the Setup, Source menu, p. 8.

Side connections

Camera or Camcorder

& Connect your camera or camcorder as shown.

é Connect to VIDEO 2 and AUDIO L 3 for mono

equipment. For stereo equipment also connect

AUDIO R 3.

S-VHS quality with an S-VHS camcorder is obtained by

connecting the S-VHS cables with the

S-VIDEO input 1 and

AUDIO inputs 3.

Do not connect cable 1 and 2 at the same time. This may cause

picture distortion !

Headphone

& Insert the plug into the headphone socket L as shown.

é Press ¬ on the remote control to switch off the internal

loudspeakers of the TV.

The headphone impedance must be between 8 and 4000 Ohm.The

headphone socket has a 3.5 mm jack.

In the Sound menu select

Headphone volume to adjust the

headphone volume.

CABLE

EXT.

CABLE

EXT.

Connect Peripheral Equipment

DIO

VIDEO

S•VIDEO

1 2 3

2288.1 en 21-01-2004 08:37 Pagina 15

Press the v key on the remote control repeatedly to select EXT1, EXT2, EXT3 or SIDE according

to where you connected your equipment at the back or the right side of your TV.

Remark : Most equipment (decoder, recorder) carries out the switching itself, when it is switched on.

To select connected equipment

See the separate supplied Cinema Link instruction manual.

Attention: the sound info on screen will not correspond with the actual sound reproduction.

Cinema Link surround receiver

Recorder or DVD with EasyLink

The recorder (VCR or DVD+RW) or DVD can

be operated with the remote control via the

Recorder or DVD menu on screen.

& Press the MENU key on the remote control.

é Select the Recorder or DVD menu with the

cursor up/down.

“ Press the cursor left/right, up/down to select

one of the recorder or DVD functions.

The key ® for recording can be operated in the TV

mode.

If your EasyLink recorder has the system standby

function, when you press the B key for 3 seconds,

both TV and the recorder are switched to standby.

Òp‡π † ® Ï

Rwd Play Stop Play Ffw Rec Eject

Recorder

Òp ‡ π † Ï

Prev. Play Stop Play Next Eject

DVD

& Connect the audio cables to the AUDIO input

of your amplifier and to

AUDIO L and R at the

back of your TV.

é The output level is controlled by the volume

control of the amplifier.

Note: Switch off the TV and your audio amplifier

before connecting them. Set the audio amplifier’s

volume to minimum.

AUDIO

Stereo amplifier and two extra front speakers

2288.1 en 21-01-2004 08:37 Pagina 16

La pagina sta caricando ...

Philips 32PW9509/05 Manuale utente

Marca: Philips

Modello: 32PW9509/05

Categoria: TV LCD

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Philips 32PW9509/05 User manual

Philips 32PW9509/05 Manuale utente

Philips 32PW9509/05 Manuale utente

in altre lingue

Documenti correlati

Altri documenti