Creative ZEN X-FI - 1 Manuale utente

Marca: Creative

Modello: ZEN X-FI - 1

Categoria: TV LCD

Tipo: Manuale utente

Information for users in the UK

(Not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some distance away from radiators

or other sources of heat. Leave a space of at least 5 cm all around the TV for ventilation, making sure that curtains, cupboards etc.

cannot obstruct the air flow through the ventilation apertures.

The TV is intended for use in a domestic environment only and should never be operated or stored in excessively hot or humid

atmospheres.

General Points

Please take note of the section 'Tips' at the end of the English section in this booklet.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help TV license holders improve

reception of BBC and IBA programmes where they are being spoilt by interference.

If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television and Radio Reception".

Mains connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate

on the rear panel of the TV. If the mains voltage is different, consult your dealer.

Important

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows :

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS1362 5A,A.S.T.A. or BSI approved type.

In order to maintain conformity to the EMC directive, the mains plug on this product must not be removed.

Connecting the aerial

The aerial should be connected to the socket marked x at the back of the set. An inferior aerial is likely to result in a poor,

perhaps unstable picture with ghost images and lack of contrast. Make-shift loft or set-top aerials are often inadequate.

Your dealer will know from experience the most suitable type for your locality.

Should you wish to use the set in conjunction with other equipment, which connects to the aerial socket such as TV games, or a

video camera, it is recommended that these be connected via a combiner unit to avoid repeated connection and disconnection of

the aerial plug.

Loop aerial (if provided)

The loop aerial packed with the set will give satisfactory reception under good signal conditions. Fit the aerial bracket and lead by

pushing the peg into the square hole in the backcover until it latches in place. Then insert the plug on the lead into the aerial

socket.

English

Your remote control 2

Preparation 3

Installation 4

Store TV channels 4

Select the menu language and country 4

Automatic installation 5

Manual installation 5

Give name 6

Reshuffle the programme list 6

Select favourite TV channels 6

Install TV setup 7-8

EasyLink features are based on the “one touch operation” approach.This

means that a sequence of actions are executed at the same time in both

the television and the video cassette recorder,

provided both are fitted

with the EasyLink function

and connected with the eurocable

supplied with your video recorder.

Installation

Operation

Use of the remote control 9-10

Use of the menus

Picture menu

Sound menu 12

Features menu 13

Dual Screen 14

NEXTVIEW 15-18

Teletext 19-21

The keys in front of the TV 21

Connect peripheral equipment

Connecting and selecting equipment 22-24

Remote control functions for peripherals 24-25

Recording 26

Tips 27

Index 27

Glossary 28

Help?

If this instruction manual does not give an answer or if

‘Tips’ do not solve your TV problem, you can call your

Local Philips Customer or Service Centre. See the

supplied World-wide guarantee booklet.

Please, have the Model and Product number which

you can find at the back of your television set or on

the packaging, ready, before calling the Philips helpline.

Model: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

2 Preparation

M h a

SMART

ACTIVE

CONTROLSMART

213

546

879

‡π

†

æ b

Mqa

MOVIE SPORT CHILD NEWS OTHER

VCR DVD SAT

TUNER CD

TAPE CDR

SMARTSMART

PICTURESOUND

¬V P

◊

yÚ

pπ

yÚ

®q

b ﬁcd

INSTANT

ZOOM

Teletext p. 20

U time display/subpage selection

f solution to puzzles

display PDC/VPS code

h enlarge

h Zoom p. 10

P no function

Smart Controls

M smart sound p. 10

h active control p. 10

a smart picture p. 10

Dual screen p. 14

b dual screen on

c no function

d still teletext picture

ﬁ strobe p. 10

B switch to standby p. 9

i on screen info p. 9

0 previous programme p. 9

◊ video recorder function p. 9

X bilingual choice/sound info p. 10

TXT language group selection p. 19

EasyLink p. 10

® INSTANT recording

q picture format p. 10

b teletext on/off p. 19

Ï main menu on/off p. 9

cursor to select

your choice p. 11

Installation p. 4

V volume up/down p. 9

¬ sound mute p. 9

P programme selection p. 9

Peripherals p. 24

w selection of EXT1, EXT2, EXT3

or FRONT

TV, video recorder (VCR), DVD,

Satellite (SAT), TUNER, CD, TAPE or

cd-recordable (CDR) selection.

Colour keys

- direct teletext page or

subject selection p. 19

Audio- and Video equipment p. 24-25

O no function

S freeze the picture p. 9

hold teletext page p. 20

Q surround modes p. 9

æ NEXTVIEW/TXT guide on/off p. 9

OK activate your choice

Your remote control

Installation

& Place the TV on a solid surface.

For ventilation, leave at least 5 cm free all around the TV.

Do not place the TV on a carpet.

To prevent any unsafe situations, do not place any objects on top of the TV.

Avoid heat, direct sunlight and exposure to rain or water.

Remove, if present, the blue protection foil at both front sides of the TV.

é Insert the aerial plug firmly into the aerial socket x at the back of

the TV.

“ Insert the mains plug in the wall socket having a mains voltage of 220V-240V.

To prevent damaging the mains (AC) cord which could cause a fire or electric

shock, do not place the TV on the cord.

‘ Remote control: Remove the cover of the battery compartment.

Insert the 2 batteries supplied (Type R6-1.5V).

Press the

TV key to be sure your remote control is in the TV mode.

The batteries supplied do not contain the heavy metals mercury and cadmium.

Nevertheless in many countries exhausted batteries may not be disposed of with

your household waste. Please check on how to dispose of exhausted batteries

according to local regulations.

Note: this remote control functions with TVs which use the RC6 signalling standard.

( Switch the TV on : Press the power switch A on the front of your TV.

A green indicator on the front of the TV lights up and the screen comes on.

If the indicator is red, press the

P+

key on the remote control.

The green lamp blinks every time you press a key on the remote control.

When you switch on your set

for the first time, the menu LANGUAGE

automatically appears on the screen.The explanation appears in different languages

one at a time. Choose your own language and press the

OK key on the remote

control.

Go on to page 4.

3Preparation

R6 / 1,5V

æ b

VCR

MOVIE OTHERNEWSCHILDSPORT

TV DVD SAT

CDTUNER TAPE CDR

CABLE

min.

R6 / 1,5 V

Preparation

Installation

After the new or extra TV channels have been stored, the TV automatically transfers

those TV channels to the video recorder if it is equipped with the EasyLink function.

The message

EasyLink : downloading ...... appears on the screen. The

programme list of the video recorder is now the same as the one of the TV. If the TV

is connected to a video recorder which supports the

NEXTVIEWLink function, the TV

also automatically transfers the language and country selections to the video

recorder.

MENU TITLE

Menu language

J INSTALLATION

MENU TITLE

United Kingdom

....

J Country

MENU TITLE

English

....

J Menu language

& Open the door of the remote control.

é Press U and f at the same time.

& Use the cursor in the up/down, left/right directions to select a menu item.

é Press the OK key to activate.

“ Use the Ï key to return or to switch the menu off.

MENU TITLE

Subject 1

Subject 2

Subject 3

J Subject 4

Subject 5

Subject 6

J Subject 4 LM

pπ

546

879

◊

X®qP

yÚ

ZOOM

INSTANT

213

æ b

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

MOVIE OTHERNEWSCHILDSPORT

select menu item

return or switch

main menu off

activate

Select the menu language and country

First, select your language and country.

& Select Menu language and press the OK key.

é Select your language and press the OK key.

Use the cursor up/down to scroll through the list and to bring up other

languages which are not displayed on the screen at present.

“ Select Country and press the OK key.

‘ Select the country where you are now located and press the OK key.

Use the cursor up/down to scroll through the list and bring up other

countries which are not displayed on the screen at present.

Select

Other when none of the countries applies.

You can now search for and store the TV channels in two different ways:

using

automatic installation or manual installation (tuning-in channel by

channel).

Select your choice and press the

OK key.

Store TV channels

To use the menus

Select the INSTALLATION menu

5Installation

Automatic installation

Start

Stop

TV is searching

One moment please ...

J Stop K

Automatic installation

Start

Stop

1 BBC1

2 BBC2

3 CNN

....

J Start K

Manual installation

(Selection mode)

System

Programme no.

Fine tune

Store

J System K

Automatic installation

In the Automatic installation menu select Start and press the OK key to

activate the searching. All TV channels are searched for and stored

automatically.

If a cable system which broadcasts ACI (Automatic Channel Installation) or a

TV channel transmitting a teletext page with the frequencies and programme

names of all the TV channels which can be received, is detected, the search is

stopped and a programme list appears.

The programme list is automatically filled with all the programme numbers

and names of the TV channels transmitted.

It is possible that the cable company or the TV channel displays a broadcast

selection menu. Layout and items are defined by the cable company or the TV channel.

Make your choice with the cursor and press the

OK key.

To exit from the menu press the Ï key on the remote control.

Go on to page 6.

Manual installation

Searching for and storing TV channels is done channel by channel.

You must go through every step of the Manual installation menu.

Selection mode is only present and lights up if the country selected also

offers the channel option (C-channels for aerial channels, S-channels for cable

channels).

You can choose either channel or frequency mode.

& Select the TV system

Select the country or part of the world from where you want to receive the

TV channel.

If you are connected to a cable system, select your country or part of the

world where you are now located.

é Press the cursor down and enter the programme number with the digit keys.

“ Search for a TV channel

Press the cursor left/right.

The frequency or the channel number increases until a TV channel is found.

Direct selection of a TV channel

If you know the frequency, the C- or S-channel number, enter it directly with

the digit keys 0 to 9.

Ask for a list from your cable company or dealer, alternatively consult the

Table of frequencies on the inside backcover of this handbook.

‘ Fine tune

In case of poor reception, you can improve the reception by adjusting the

frequency with the cursor left/right.

( To store your TV channel, select Store and press the OK key.

Repeat steps

& to ( to store another TV channel.

§ To exit from the menu press the Ï key on the remote control.

Installation

It is possible to change the name stored in the memory or to assign a name

to a TV channel which has not yet been entered.A name with up to 5 letters

or numbers can be given to the programme numbers 0 to 99. For example

SUPER, BBC1,... Between 99 and 0 you can also name any peripherals that

are connected to a euroconnector.

& Select Give name in the INSTALLATION menu and press the OK key.

é Select the programme number.

“ Press the OK key.

‘ Select the character with the cursor up/down.

( Select the following position with the cursor right.

§ Select the following character.

è Press the OK key when finished.

! Press the Ï key to return to the INSTALLATION menu.

Space, numbers and other special characters are located between Z and A.

According to your preference you can change the order of the stored TV

channels.

& Select Reshuffle in the INSTALLATION menu and press the OK key.

é Select the programme number you want to exchange.

“ Press the OK key.

‘ Select the new number you want to exchange it with.

( Press the OK key.

Repeat the operation until all TV channels are allocated as you like.

§ Press the Ï key to return to the INSTALLATION menu.

After leaving the installation you can browse through the TV channels by

pressing the

- P + key. Only those TV channels which are in the favourite list

will be displayed. Non-favourite TV channels can still be selected with the digit

keys. By default all stored channels are added to the favourite list.

& Select Favourite programmes in the INSTALLATION menu and press

the

OK key.

é Select your favourite programme number.

“ Select Ye s or No with the cursor left/right.

‘ Repeat for every TV channel you want to make a favourite or a

non-favourite TV channel.

( Press the Ï key to return to the INSTALLATION menu.

In order for NEXTVIEW to function properly, the first TV channel from the favourite list

should also broadcast the correct local date and time via teletext.

INSTALLATION

Menu language

Country

Automatic installation

Manual installation

Give name

Reshuffle

Favourite programmes

SETUP

J Give name

Give name

EXT1

EXT2

EXT3

FRONT

1 BBC1

2 BBC2

3 ....

4 ....

5 ....

J 0

Reshuffle

1 CNN

2 BBC2

3 ....

4 ....

5 ....

J 1 CNN

Favourite programmes

EXT1

EXT2

EXT3

FRONT

0 ... No

1 ... Yes

2 ... No

3 .... No

4 .... Yes

5 ....

J 2 ... Yes

Select Favourite TV channels

Reshuffle the programme list

Give name

7Installation

The Setup menu allows you to adjust initial settings, i.e. those which are not

related to the installation of the TV channels.

The Setup menu contains items that control the settings of the TV’s functions,

features, services and peripherals you may have connected.

& Use the cursor in the up/down, left/right directions to select the menu item.

é Use the OK key to activate.

“ Use the Ï key to return or switch menu off.

Digital sources (for future use)

Define Decoder/Descrambler programme numbers

If a decoder or a descrambler is connected, see p. 22, you can define one or

more programme numbers as decoder programme numbers.

Press the cursor left/right to select the input used to connect to your

decoder

Off, EXT1 or EXT2.

Select

Off if you do not want the selected programme number being

activated as a decoder programme number.

Select EXT2 when the decoder is connected to your EasyLink video recorder.

When selecting the decoder, the message

EasyLink: downloading presets....

appears on the screen.

Picture tilt

Select Picture tilt with the cursor up/down.

Keep the cursor left/right pressed to adjust the rotation of the picture.

Information line

Select On and after the selection of a TV programme or after pressing the

i key on the remote control, a TV channel which broadcasts teletext may

transmit the name of the TV channel, the programme name or another

message.This is displayed on screen next to information about sound and

picture format.

When selected

Off, only sound and picture format information is displayed

after the selection of a TV channel or after pressing the

i key.

Factory settings

Select Factory settings and press the OK key to restore picture and sound

settings, predefined in the factory.

Auto Format

Selecting Yes causes the screen to automatically fill as much of the picture as

possible when TV programmes are not carrying special signals detecting the

correct screen format.

With the

q key on the remote control you can still select other picture

formats. See p. 9.

INSTALLATION

Menu language

Country

Automatic installation

Manual installation

Give name

Reshuffle

Favourite programmes

SETUP

J SETUP

Decoder/Descrambler

Programme

Decoder status

J Programme

SETUP

Digital Sources

Decoder/Descrambler

Picture tilt

Information line

Factory settings

Auto format yes/no

Auto Surround

INSTALLATION

J Decoder/Descrambler

Install TV Setup

Installation

Auto Surround

Sometimes the broadcaster transmits special signals for Surround Sound

encoded programmes. In that case, the TV automatically switches to the

best Surround Sound mode when Auto Surround is switched on. Virtual

Dolby* Surround will be reproduced, see p. 9.

Overruling this surround mode remains possible.

Installation

Select Installation and press the OK key to return immediately to the

INSTALLATION menu.

‘ To exit from the menu press the Ï key repeatedly.

SETUP

Digital Sources

Decoder/Descrambler

Picture tilt

Information line

Factory settings

Auto format yes/no

Auto Surround

INSTALLATION

J Auto Surround

‘Dolby’ ‘Pro Logic’ and the double-D symbol are

trademarks of Dolby Laboratories Licensing Corporation.

Manufactured under license from Dolby Laboratories

Licensing Corporation.

9Use of the remote control

M h a

SMART

ACTIVE

CONTROL

SMART

PICTURESOUND

213

546

879

‡π

†

æ b

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

◊

MOVIE SPORT CHILD NEWS OTHER

w Select peripherals

Press this key repeatedly to select EXT1,

EXT2, EXT3 or FRONT, according to where

you connected the peripherals (p. 24).

TV VCR DVD SAT TUNER CD TAPE CDR

Press one of these keys to use the remote

control directly in the TV, video recorder,

DVD or satellite mode. A green indicator

lights up. Press the same key again within 3

seconds to use the remote control in the

mode indicated below the key (tuner, CD,

tape or CD-recordable).

A red indicator lights up.

Press the key again to return to the function

mentioned above the key.

B Standby

The set is switched off.

To switch the TV on again, press

- P + or the

digit keys.

If your EasyLink video recorder has the

system standby function and you press the

standby key for 3 seconds, both the TV and

video recorder are switched to standby.

Your TV consumes energy in the standby mode.

Energy consumption contributes to air and water

pollution.We advise to switch off your TV

overnight instead of leaving it on standby.You

save energy.

®Ò‡π†Video recorder see p. 24

æ NEXTVIEW/TXT Guide on off

see p. 15

OK Press this key to activate your choice,

when in the menus.

S Freeze

To activate/de-activate the frozen picture and

to hold a teletext page.

Q Surround modes

Incredible Surround

With stereo transmission, and when

Incredible Surround is selected, it seems as

though the loudspeakers are spread further

apart from one another.

Virtual Dolby Surround

(optimal with Dolby Surround signals)

Virtual Dolby Surround enables you to

experience the effect of Dolby Surround Pro

Logic, reproducing a rear sound effect.

See Sound menu,Virtual Dolby effect, p. 12.

i Screen information

Press for 5 seconds to activate/de-activate

the extended or reduced display of TV

channel and programme information on the

screen.

Press briefly to display information about the

selected TV channel and programme, the

sound reception, picture settings and the

remaining time set with the sleeptimer.

0/9 Digit keys

To select a TV channel.

For a two digit programme number, enter the

second digit within 2 seconds.

To switch immediately to a selected one digit

TV channel, keep the digit key pressed a bit

longer.

0 Previous programme

The previously selected TV channel is displayed.

The

◊ indication is only for video recorder.

b Teletext on/off see p. 19

Ï Main menu on/off see p. 11

V Volume

Press + or - to adjust the volume.

¬ Mute

Temporarily interrupt the sound or restore

it.

P Programme selection

To browse through the TV channels

activated in the Favourite Programme menu.

Use of the remote control

Operation

Use of the remote control

X®qP

INSTANT

ZOOM

yÚ

TV VCR DVD SAT

TUNER CD TAPE CDR

V P

◊

MOVIE SPORT CHILD OTHER

NEWS

‡ π

†

1 2 3

546

879

bcd

Mah

SMARTSMART

ACTIVE

CONTROL

ﬁ

Smart Keys

To select predefined picture and sound settings.

M Smart Sound

Each time it is pressed, a different sound setting is selected, corresponding

with specific factory settings of the graphic equalizer.

a Smart Picture

Each time it is pressed, a different picture setting is selected, corresponding

with specific factory settings of Contrast, Colour, Sharpness and Dynamic

Contrast.

Personal refers to the personal preference settings of picture and sound

selected in the picture and sound menu.

Remark: the moment you are in a predefined smart sound or picture setting and you

modify a setting in the picture or sound menu, all values of the menu will overwrite

the previously made settings.

ﬁ Strobe

Press this key to reproduce the picture image by image.

Press the

ﬁ key again to have a faster speed.

Press the

ﬁ again to switch off the strobe function.

U Time display

The time, downloaded from the TV channel

(with teletext) stored on programme number

1 or the lowest favourite programme number,

is displayed on the screen.

This function is not available when continuous

subtitles have been switched on.

SUfh Teletext functions

ee p. 20

h Zoom

Press the ZOOM h key repeatedly to select

one of the zoom magnifications (x1, x4, x9,

x16). Additionally you can shift the selected

zoom window over the screen with the cursor.

Press

i to activate/de-activate the

continuous display of the zoom magnification.

The zoom window is reset after: selecting

another TV channel, another picture format or

when another picture format is selected

automatically.

Zooming is disabled in Dual screen mode.

h Active control

Active control is a pro-active and automatic

system.The TV continuously measures and

corrects all incoming signals in order to

provide the best picture possible.

Press the

h key to select the Active Control

values Off or On.

Off Sharpness and Dynamic Contrast are

controlled automatically

On Sharpness, Dynamic Contrast and Noise

Reduction are controlled automatically.

Press the cursor in the up/down directions

while the selected Active Control setting

information is on top of the screen.

The Active Control menu appears.

The picture settings are being adapted

continuously and automatically.

The menu items cannot be selected.

Press the cursor in the up/down directions

again to switch off the menu.

X Bilingual choice and

sound mode selection

Press this key

• to switch from

Stereo to Mono sound, in

case of stereo transmission, or from

Nicam Stereo to Nicam available, in case

of digital transmission;

• to choose between language

Y (Dual Y) or

language

Z (Dual Z), in case of bilingual

transmission.The setting is separately

stored for each TV channel.

® Instant record

If your video recorder has the EasyLink

function the

INSTANT ® key for record can

be operated in the TV mode.

q Picture format

Press this key repeatedly to select another

picture format: 4:3, Movie Expand 14:9,

Movie Expand 16:9 with or without subtitling,

Wide Screen, Super Zoom or Automatic

(when Auto format is set to Yes in the

SETUP menu).

Auto format makes the picture to fill the

screen as much as possible.

Sometimes also video recorder programmes

carry special signals which will automatically

switch the TV to the correct screen format.

Auto format is disabled when in Dual screen.

When in Movie Expand 14:9 or 16:9 or

Super Zoom picture format you can make

subtitles visible with the cursor up/down.

P no function

11Use of the menus

PICTURE

Contrast

Brightness

Colour

Sharpness

Tint

Digital options

Dynamic Contrast

J Contrast L M

MAIN MENU

Contrast

SOUND

FEATURES

PROGRAMMES

J PICTURE

OK key to activate

cursor to select

adjustments

return or switch

main menu on/off

213

546

æ b

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

MOVIE OTHERNEWSCHILDSPORT

& Press the Ï key to display/cancel the MAIN MENU.

é Use the cursor in the up/down directions to select the PICTURE, SOUND or

FEATURES menu or to select the PROGRAMMES.

“ Press the cursor right to activate the selected menu.

‘ Use the cursor in the up/down, left/right directions to select the menu item.

( Use the OK key to activate.

§ Press the Ï key repeatedly to return or to switch the menu off.

Picture menu

If an NTSC peripheral is connected to one of the euroconnectors, the option Hue

also appears.

Tint

Select the colour temperature: Normal, Warm or Cool.

Digital options

Although Natural Motion is the most ideal setting, it may be preferable to

switch back to Digital Scan and/or 100 Hz.

To make all the 4 digital options available at the same time and selectable, first

select a 4:3 picture format.

•

100 Hz = 100 Hz only (Field flicker reduction)

•

Dig. Scan = 100 Hz + Dig. Scan (Field and line flicker reduction)

•

Natural Motion = 100 Hz + Dig. Scan + Natural Motion (Field and line

flicker reduction and smooth movement reproduction)

•

Double lines = provides for a doubling of vertical resolution which adds

astonishing sharpness and a total absence of visible picture lines.

Motion compensation reduces jitter and offers smooth, yet sharp motion

reproduction.

Note: if the menu item Digital options is not present, first select a 4:3 picture format

with the

q key.

Dynamic Contrast

To make the contrast in the darker and the brighter picture areas more

noticeable, select the

Med setting.

In certain circumstances it may be preferred to select

Min, Max or Off.

The modified adjustments for Contrast, Brightness, Colour, Sharpness,Tint,

Digital Scan and Dynamic Contrast are automatically stored for all TV

channels.

Select

Factory settings in the Setup menu to restore the predefined factory

settings, see p. 7.

Use of the menus

SOUND

Volume

Balance

Graphic Equalizer

Headphone Volume

AVL

Delta volume

Virtual Dolby effect

J Volume L M

OK key to activate

cursor to select

adjustments

return or switch

main menu on/off

213

546

æ b

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

MOVIE OTHERNEWSCHILDSPORT

Sound menu

& Press the Ï key to display/cancel the MAIN MENU.

é Use the cursor in the up/down directions to select the SOUND menu.

“ Use the cursor in the up/down, left/right directions to select the menu item.

‘ Use the OK key to activate.

( Press the Ï key repeatedly to return or to switch the menu off.

The modified adjustments for Volume, Balance, and Graphic equalizer are

automatically stored for all TV channels.

Select

Factory settings in the Setup menu to restore the predefined factory

settings, see p. 7.

Graphic Equalizer

Here you can select the preferred sound setting which corresponds with the

personal sound settings.

Headphone volume

See Connect Peripheral Equipment, p. 23, for the connection of the

headphone.

AVL (Automatic Volume Leveller)

AVL automatically controls the volume level to avoid too large level

differences, especially when switching to another programme or during

commercial breaks.

AVL will reduce the dynamics of the sound.To maintain original dynamics, use

the Delta volume feature.

Delta volume

Here you may adjust the volume differences of each selected TV channel or

external device separately.This can compensate volume differences between

different broadcasters.

Use the

- P + keys to compare to the volume of other TV channels or

externals.

Virtual Dolby effect

Virtual Dolby enables you to experience the effect of Dolby Surround Pro

Logic without the need of having rear speakers connected or activated.

Select the level of

Virtual Dolby effect with the cursor left/right.

13Use of the menus

Sleeptimer Off

Child lock Off

Subtitle Off

J FEATURES

OK key to activate

cursor to select

adjustments

return or switch

main menu on/off

213

546

æ b

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

MOVIE OTHERNEWSCHILDSPORT

Features menu

& Press the Ï key to display/cancel the MAIN MENU.

é Use the cursor in the up/down directions to select the FEATURES menu.

“ Press the cursor right to activate the selected menu.

‘ Use the cursor in the up/down directions to select a menu item.

( Use the cursor in the left/right directions to select the desired setting.

Sleeptimer

With the sleeptimer you can set a time period after which the TV should

switch itself to standby.

The counter runs from

Off up to 180 min.

One minute before the TV is set to go to standby, the remaining seconds

appear on screen. Not visible in dual screen mode.You can always switch off

your set earlier or change the set time.

Child lock

If the child lock is on, the TV can only be switched on with the remote

control.The

P - and + keys in front of the TV cannot be used to select a TV

channel. In this way you can prevent unauthorised use of your TV.

If the message

Child lock On appears, the child lock must be switched off

before you can use the

P - and + keys in front of the TV to select a TV

channel.

Subtitle

TV channels with teletext often transmit certain programmes with subtitling.

See Teletext, Continuous Subtitles, p. 21 how to select the proper subtitle

page from the teletext index.

Select

Subtitle On or Off.

Press the

Ï key to switch off the Features menu.

Programme list

& Press the Ï key to display/cancel the MAIN MENU.

é Select PROGRAMMES with the cursor up/down.

“ Press the cursor right to display an overview of all the TV channels installed.

‘ Press the cursor up/down to run through the list and press OK to select the

desired TV channel.

( Press the Ï key to switch off the Programme list.

Dual Screen

& Press the b key to switch on Dual Screen.

The TV screen is divided into 2 parts:

- the left side for the normal main picture,

- the right side for teletext broadcast by the selected TV channel or for

NEXTVIEW/Teletext Guide.

To operate NEXTVIEW/Teletext Guide, see p. 15.

To operate teletext, see p. 19.

If Dual Screen is Off, the picture, teletext or NEXTVIEW/Teletext Guide are displayed

full screen.

é Press the q key under the door of the remote control to select a vertical

squeezed or a non vertical squeezed picture size.

“ Press + P - to run through the teletext pages.

‘ Select still teletext picture.

Press the

d key to freeze only the teletext picture.The info in this page is

not being updated by the teletext broadcaster.

( When in Teletext Dual Screen, press the b key to return to a full picture

screen or press the

b key to return to a full Teletext screen.

§ When in NEXTVIEW/Teletext Guide Dual Screen, press the æ key to return

to a full picture screen or press the

b key to return to a full

NEXTVIEW/Teletext Guide screen.

213

546

879

æ b

S Q

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

◊

X®q P

yÚ

ZOOM

INSTANT

bdc ﬁ

Mah

SMARTSMART

ACTIVE

CONTROL

Dual Screen

15NEXTVIEW

“ Enter the proper programme guide page number

with the digit keys or with the

– P + keys.

‘ Press the cursor left/right to run through the

subpages.

( Select a programme with the cursor up/down.

§ Press one of the colour keys to select one of the

basic functions (if available);

record, remind, info.

See Basic functions further on.

è Press the OK key to return to the header area

again.

“ Select a programme with the cursor up/down.

‘ Press one of the colour keys to select one of the

basic functions (if available);

record, remind, info.

See Basic functions further on.

( Press the OK key to return to the header area

again.

OK key

to activate

cursor to select

adjustments

213

546

æ b

TV VCR DVD SAT

TUNER CD TAPE CDR

¬V P

MOVIE OTHERNEWSCHILDSPORT

NEXTVIEW

selection

Channel Overview

BBC1 BBC2

p.202

p 01 02 ... π

BBC1

11.03 ................

14.35 ................ 226/3

17.50 ................ 231

Record

Remind

Info

Teletext Guide NEXTVIEW

Monday 9 Oct 18:03

Channel Theme Overview

BBC1

NEX

IEW

What’s on now

Preview

Themes

Ratings

Record

Remind

Info

Today, most broadcasters in Europe, are offering teletext pages containing

their programme schedule of today.These pages can be requested by switching

the TV to

Teletext Guide.

An increasing number of broadcasters are offering an extended programme

guide service called

NEXTVIEW. NEXTVIEW is a new way of presenting

programme schedules and offers more features than common teletext.

With

NEXTVIEW it is possible to show for instance all the movies coming

tonight.

Both facilities are integrated in this TV:

NEXTVIEW and Teletext Programme

Guide. If a TV channel supports

NEXTVIEW then the TV will automatically

present the

NEXTVIEW programme schedule. If the TV channel supports just

teletext, then the TV will switch automatically to Teletext Guide.

Both facilities are offering the same functions: record, remind and info.

However in case of Teletext Guide the broadcaster is responsible if these

functions are possible.

You can search for the programmes you want to watch up to 7 days in

advance. It is also possible to search for a programme by theme, e.g. sport,

movie, etc. Once a programme has been selected it can be tagged, to remind

you, or to record on the video recorder automatically (provided the video

recorder is equipped with

NEXTVIEWLink Level 2.0), once, daily, weekly or

series.Teletext Guide/

NEXTVIEW also allows direct access to detailed

information about programmes if provided by the broadcaster.

The broadcaster is responsible for the contents of the information.

The TV is responsible for the capture of that information and for the presentation to

the user.

Use of the Teletext Guide/NEXTVIEW menus

& Press the æ key on the remote control to display/cancel the Teletext Guide/

NEXTVIEW menu.

é Use the cursor in the up/down, left/right directions to select the date,

CHANNEL for the channel guide, THEME for the theme guide, OVERVIEW

for an overview of all the programmes which are marked as reminders or for

recording, the programme guide page number or to enter the programme list.

NEXTVIEW / Teletext Guide

NEXTVIEW

Channel Theme Overview

BBC 1 BBC 2 CNN

p.202

p 01 02 ... π

BBC 2

11.03 ................

14.35 ................ 226/3

17.50 ................ 231

One moment please

Record

Remind

Info

Monday 9 Oct 18:03

Channel Theme Overview

BBC1 CNN BBC2

BBC1

NEX

IEW

........

Record

Remind

Info

Monday 9 Oct 18:03

Channel Theme Overview

Culture Movie ....

BBC1

NEX

IEW

BBC1

CNN

TVE

Record

Remind

Info

Monday 9 Oct 18:03

Channel Theme Overview

BBC1

NEX

IEW

BBC1 17.10

CNN 17.30

TVE 18.05

BBC2 19.00

Record

Remind

Info

Teletext guide

TV channels which broadcast teletext also transmit a page with the

programme guide of the day. For each selected TV channel the programme

guide page can be selected with the

æ key:

- automatically if the selected TV channel supports services like PDC

(Programme Delivery Control) or MIP (Magazine Inventory Page).

- if automatic pre-selection is not possible then the index page is displayed

and the proper programme guide page number of the selected TV channel

has to be entered with the digit keys.

The programme guide page will be stored automatically only if it satisfies

Video Programming via Teletext (VPT) requirements.

Every time you press the

æ key, the programme guide page of the

selected TV channel will be available if the TV channel does not support

NEXTVIEW.

The function items record, remind and info, corresponding with the coloured

keys, become highlighted if the displayed programme page satisfies the Video

Programming via Teletext (VPT) requirements. Select a programme item and

press one of the function keys, e.g. Record or Remind. See Basic functions

further on.

The Info item is enabled if the selected programme contains a page number

with an optional subcode referring to a page with more info about the

programme.

NEXTVIEW modes to sort and represent information

Channel

The Channel guide provides an overview of all programmes that are

broadcast by a single channel during one day.

Already passed programmes can be made visible via cursor up.

The list will start with the earliest broadcast programme.

With cursor left/right another favourite TV channel can be selected.

Theme

The theme guide displays a list of all programmes at the selected date, that

matches with the selected category (news, sport, culture, movies, …).

The default starting item will be the current or next programme on the

current TV channel.

The

THEME selection is only present if programmes in the TV guide have

defined themes.

Overview

The Overview menu provides a list of programmes that are marked as

reminders or to be recorded each day.

When more than one programme to be recorded has an overlap in time,

these programmes will be marked by a red colour.

After the programme has been broadcast, all items set for once will be

deleted from the list the following day.This menu can be used to change a

reminder or recorder.

Note: the TV will automatically interpret the broadcast time (as shown on the

teletext guide) of your selected programme into the correct local time and

date.

17NEXTVIEW

Record

Remind

Info

Info block

Date time

CHANNEL THEME OVERVIEW

CNN

11.03 Travel Guide

14.35 World news

17.50 Insight

............................

Once

Daily Weekly Clear

Basic functions

The functions Record, Remind and Info can be activated with the

corresponding colour keys on the remote control.

If the function is not available, then the text is shown at reduced brightness.

Select a programme with the cursor up/down.

Record R or Remind !

& Press the red colour key to activate Record or the green colour key to

activate

Remind.

If the programme number of the broadcaster is not yet known, a message appears

with the request to input the correct programme number with the cursor left/right.

Press OK.

A small menu pops up in which you can choose the interval: once, daily or

weekly, or clear an earlier made record or remind setting.The default interval

is set to

Once. If a programme is an episode of a series, it is identified by the

system and the options

daily and weekly are replaced by the option series.In

this case the system identifies when the next episode of the series will be

broadcast.This is not possible in the Teletext guide.

é Use the cursor in the left/right directions to select the interval.

The colour of the tag refers to the interval.

“ Press the OK key.

When

Record R is activated:

Storing is displayed to indicate the video recorder is programmed.

When

Remind ! is activated:

- a message will be displayed the moment the tagged programme

with

! starts, when watching the TV later on.

- the TV switches on the moment the tagged programme with

! starts,

when the TV is in standby.

Note: Recordings and reminders are not possible when the broadcaster does not

transmit dates and times of the programmes.

The message

No TV programming possible appears.

Make sure you are on the TV programming page.

Info

& Press the yellow colour key to activate Info.

Advertisements or information relating to the selected programme are

displayed. In some cases all of the information does not fit on the screen. Use

the cursor up/down to browse through all the information.

é Press the yellow colour key again to switch off the information.

NEXTVIEW

213

546

879

æ b

TV VCR DVD SAT

TUNER

MOVIE SPORT CHILD NEWS OTHER

CD TAPE CDR

¬V P

◊

b cdﬁ

Mah

SMARTSMART

ACTIVE

CONTROL

Select Picture/NEXTVIEW-Teletext Guide

Press the æ key.

Press the

b key.

The screen is divided into two parts: the left side for the normal main picture,

the right side for

NEXTVIEW/Teletext Guide.

Press the

b key to return to a full NEXTVIEW/Teletext guide screen or

press the

æ key to return to a full picture screen.

Acquisition and updating of NEXTVIEW information

Acquisition and updating of NEXTVIEW is done when you are watching a TV

channel supporting

NEXTVIEW.

Video recorder restrictions with NEXTVIEW

The Record item and the automatic recording will only be present and

possible if your video recorder is equipped with

NEXTVIEWLink.

Your video recorder should be connected to

EXTERNAL 2. See Connect

Peripheral Equipment, p. 22.

The daily, weekly and series options, the number of recordings set and the

way overlapping recordings are managed, depend on the type of video

recorder you have.When all video recorder timers are full, the item

Record

in the menu will not be present.

Upload video recorder overview.

When the TV is switched on, the timer recordings are uploaded to the TV to

check if any manual addition or deletions have been done.This is shown in the

overview.

The video recorder manages and removes timer recordings when performed.

Some

NEXTVIEWLink video recorders do not allow a daily programming of the

recording to start on a Saturday or Sunday. In this case the item

daily will be

removed from the menu on those days.

La pagina sta caricando ...

Creative ZEN X-FI - 1 Manuale utente

Marca: Creative

Modello: ZEN X-FI - 1

Categoria: TV LCD

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Creative ZEN X-FI - 1 User manual

Creative ZEN X-FI - 1 Manuale utente

Creative ZEN X-FI - 1 Manuale utente

in altre lingue

Documenti correlati

Altri documenti