Moog Videolarm IRHW75CF2N Istruzioni per l'uso

Marca: Moog Videolarm

Modello: IRHW75CF2N

Categoria: Accessori per telecamere di sicurezza

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

www.videolarm.com

R H W 7 5 C F 2 N / I R H W 7 5 C F 2 N

Outdoor / Indoor Dome Housing Brackets and Mounts

Installation and Operation Instructions for the following models:

RHW75CF2N IP Network Ready 7” Vandal-Resistant Outdoor dome housing with wall mount,

rugged cast aluminum top and polycarbonate clear dome, with 24Vac input,

heater/blower, for an IP Network xed camera, 120 to 24Vac transformer

RHW75TF2N IP Network Ready 7” Vandal-Resistant Outdoor dome housing with wall mount, rugged cast

aluminum top and polycarbonate tinted dome, with 24Vac input, heater/blower, for an IP

Network xed camera, 120 to 24Vac transformer

IRHW75CF2N IP Network Ready 7” Vandal-Resistant Indoor dome housing with wall mount, rugged cast

aluminum top and polycarbonate clear dome, with 24Vac input, heater/blower, for an IP

Network xed camera, 120 to 24Vac transformer

RHW7CF2 Vandal-Resistant Outdoor dome housing with wall mount, rugged cast aluminum

top and polycarbonate clear dome, with 24Vac input, for an xed analog camera

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5377

01-31-2012

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualied installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

Contents of Box

Pendent Model

(ONLY)

* NOT included with E or 12V models

RHW75CF2N (Outdoor Only)

IRHW75CF2N (Indoor Only)

Power 24VAC

Class 2 Only

Total Power: 79 Watts

Heater: 50 Watts Blower: 2 Watts

Camera Power: 27 Watts (MAX)

Input Connectors (Outdoor Units):

(1) BNC (Analog Video)

(2) Screw-Down Connectors (Power/Alarms)

(1) RJ45 (Data)

Energía Total: 79 vatios

Calentador: 50 vatios Soplador: 2 vatios

Energía De la Cámara fotográca: 27 vatios (MAX)

Conectadores De la Entrada (Unidades Al aire libre):

(1) BNC (Vídeo Análogo)

(2) Conectadores Del Tornillo-Abajo (Power/Alarms)

(1) RJ45 (datos)

Tools Required: .100” Flat Head Screwdriver Phillips Head Screwdriver

25 vatios en 24 VAC (cámara fotográca solamente)

Ningunos Conectadores De la Entrada: Todo el cableado debe ser funcionado directamente

a la cámara fotográca

Las Herramientas Requirieron: Destornillador Principal Plano Del 100" Destornillador

Principal Phillips

Electrical Specications

25 Watts at 24 VAC (Camera Only)

No Input Connectors: All wiring is to be ran directly to the camera

Puissance Totale: 79 watts

Réchauffeur: 50 watts Ventilateur: 2 watts

Puissance D'Appareil-photo: 27 watts (MAX)

Connecteurs D'Entrée (Unités Extérieures):

(1) BNC (Vidéo Analogue)

(2) Connecteurs De Vis-Vers le bas (Power/Alarms)

(1) RJ45 (données)

Gesamtenergie: 79 Watt

Heizung: 50 Watt Gebläse: 2 Watt

Kamera-Energie: 27 Watt (MAX)

Eingang Stecker (Im Freienmaßeinheiten):

(1) BNC (Analoger Bildschirm)

(2) Schraube-Unten Stecker (Power/Alarms)

(1) RJ45 (Daten)

Poder Total: 79 watts

Calefator: 50 watts Ventilador: 2 watt

Poder Da Câmera: 27 watts (MAX)

Conectores Da Entrada (Unidades Ao ar livre):

(1) BNC (Vídeo Análogo)

(2) Conectores Do Parafuso-Para baixo (Power/Alarms)

(1) RJ45 (dados)

Alimentazione Totale: 79 watt

Riscaldatore: 50 watt Ventilatore: 2 watt

Alimentazione Della Macchina fotograca: 27 watt (MAX)

Connettori Dell'Input (Unità Esterne):

(1) BNC (Video Analog)

(2) Connettori Della Vite-Giù (Power/Alarms)

(1) RJ45 (dati)

25 watts à 24 VCA (appareil-photo seulement)

Aucuns Connecteurs D'Entrée : Tout le câblage doit être couru directement à l'appareil-photo

Les Outils Ont exigé : Tournevis Principal Plat De 100" Tournevis Principal Phillips

25 Watt bei 24 VAC (nur Kamera)

Keine Eingang Stecker: Alle Verdrahtung soll direkt zur Kamera gelaufen werden

Werkzeuge Erforderten: 100"Flacher Hauptschraubenzieher Kreuzkopfhauptschraubenzieher

25 watts em 24 VAC (câmera somente)

Nenhuns Conectores Da Entrada: Toda a ação deve ser funcionada diretamente à câmera

As Ferramentas Requereram: Chave de fenda Principal Lisa Do 100"Chave de fenda

Principal Phillips

25 watt a 24 VCA (macchina fotograca soltanto)

Nessun Connettori Dell'Input: Tutti i collegamenti devono essere fatti funzionare direttamente

alla macchina fotograca

Attrezzi Richiesti: Cacciavite Capo Piano Del 100" Cacciavite Capo "phillips"

Français

Deutsch

Italiano

Portuguese

Español

English

Français

Deutsch

Italiano

Portuguese

Español

English

RHW7CF2

Included only with *F2N models

Bracket is designed for 45° conduit tting (If using the

conduit). Run wire into bracket, secure to wall.

• El soporte se diseña para la guarnición del conducto 45° (si usa el

conducto). Funcione con el alambre en el soporte seguro para

emparedar.

• La parenthèse est conçue pour l'ajustage de précision du conduit 45° (si

à l'aide du conduit). Courez le l dans la parenthèse bloquée pour murer.

• Haltewinkel ist für Befestigung des Rohres 45° bestimmt (wenn das Rohr

verwendet wird). Lassen Sie Draht in den Haltewinkel laufen, der, um zu

ummauern sicher ist.

• O suporte é projetado para o encaixe da canalização 45° (se usando a

canalização). Funcione o o no suporte seguro para murar.

• La staffa è progettata per il montaggio del condotto 45° (se per mezzo

del condotto). Faccia funzionare il legare nella staffa sicura per murare.

Trim incoming control & power wires to 4”- 5”,

for either wall or pendent bracket.

• & entrante del control del ajuste; accione los alambres a 4” - 5”, para

la pared o el soporte pendiente.

• & entrant de commande d'équilibre ; actionnez les fils à 4 » - 5 », pour

le mur ou la parenthèse en suspens.

• Ankommendes & Steuer der Ordnung; antreiben Sie Drähte bis 4“ - 5“,

entweder für Wand oder pendent Haltewinkel r.

• & entrante do controle da guarnição; pnha fios a 4” - 5”, para a

parede ou o suporte pendent.

• & ricevuto di controllo della disposizione; alimenti i legare a 4„ - 5„,

per la parete o la staffa pendent.

4”-5”

Secure lanyard to lanyard clip.

• Asegure el acollador al clip del acollador.

• Fixez la lanière à l'agrafe de lanière.

• Befestigen Sie Abzuglinie an Abzuglinieclip.

• Fixe o colhedor ao grampo do colhedor.

• Assicuri la cordicella alla clip della cordicella.

Complete ALL wiring connections.

• Termine TODAS LAS conexiones del cableado.

• Accomplissez TOUS LES raccordements de câblage.

• Schließen Sie ALLE Verdrahtungsanschlüsse ab.

• Termine TODAS AS conexões da fiação.

• Completi TUTTI I collegamenti dei collegamenti.

WALL MOUNTING

52 Watts

COAX

(coax wire not supplied)

27 Watts

Wiring the dome can be completed by

referring to the diagram.

• Atar con alambre la bóveda puede ser terminada

refiriendo al diagrama.

• Le câblage du dôme peut être accompli en se

rapportant au diagramme.

• Das Verdrahten der Haube kann durchgeführt

werden, indem man auf das Diagramm sich bezieht.

• Wiring a abóbada pode ser terminado consultando

ao diagrama.

• Legare la cupola può essere completato riferendosi

allo schema.

Align large arrows.

• Alinee las flechas grandes.

• Alignez les grandes flèches.

• Richten Sie große Pfeile aus.

• Alinhe grandes setas.

• Allini le grandi frecce.

Important

Gasket

Must be in

place

To lock, turn clockwise.

• Para trabarse, dar vuelta a la derecha.

• Pour fermer à clef, tourner dans le sens des aiguilles d'une montre.

• Zu sich verriegeln, nach rechts drehen.

• Para travar, para girar no sentido horário.

• Per per chiudere, girare in senso orario.

Secure with ¼” Allen wrench.

• Asegure con la llave Allen del ¼”.

• Fixez clé Allen avec de ¼ ».

• Sichern Sie mit ¼“ Inbusschlüssel.

• Fixe com chave Allen do ¼ de”.

• Fissi con chiave di Allen del ¼„.

WALL MOUNTING

Trim incoming control and power wires to 4-5” for

either wall or pendent bracket.

• Ajuste los alambres entrantes del control y de la energía a

4-5” para la pared o el soporte pendiente.

• Équilibrez les fils entrants de commande et de puissance à 4-5

» pour le mur ou la parenthèse en suspens.

• Trimmen Sie ankommende Steuer- und Energiendrähte bis

4-5“ entweder für Wand oder pendent Haltewinkel.

• Apare fios entrantes do controle e do poder a 4-5” para a

parede ou o suporte pendent.

• Assetti i legare ricevuti di potere e di controllo a 4-5„ per la

parete o la staffa pendent.

4”-5”

Secure lanyard to lanyard clip.

• Asegure el acollador al clip del acollador.

• Fixez la lanière à l'agrafe de lanière.

• Befestigen Sie Abzuglinie an Abzuglinieclip.

• Fixe o colhedor ao grampo do colhedor.

• Assicuri la cordicella alla clip della cordicella.

Complete all wiring connections

(coax wire not supplied).

• Termine todas las conexiones del cableado

(alambre coaxil no suministrado).

• Accomplissez tous les raccordements de câblage

(fil coaxial non fourni).

• Schließen Sie alle Verdrahtungsanschlüsse ab

(koaxialer Draht nicht geliefert).

• Termine todas as conexões da fiação

(fio co-axial não fornecido).

• Completi tutti i collegamenti dei collegamenti

(legare coassiale non fornito).

52 Watts

COAX

(coax wire not supplied)

27 Watts

Wiring the dome can be completed by

referring to the diagram.

• Atar con alambre la bóveda puede ser terminada

refiriendo al diagrama.

• Le câblage du dôme peut être accompli en se

rapportant au diagramme.

• Das Verdrahten der Haube kann durchgeführt

werden, indem man auf das Diagramm sich bezieht.

• Wiring a abóbada pode ser terminado consultando

ao diagrama.

• Legare la cupola può essere completato riferendosi

allo schema.

FOR PENDENT/

WALL MOUNTING

Align large arrows.

• Alinee las flechas grandes.

• Alignez les grandes flèches.

• Richten Sie große Pfeile aus.

• Alinhe grandes setas.

• Allini le grandi frecce.

To lock, turn clockwise.

• Para trabarse, dar vuelta a la derecha.

• Pour fermer à clef, tourner dans le sens des aiguilles d'une

montre.

• Zu sich verriegeln, nach rechts drehen.

• Para travar, para girar no sentido horário.

• Per per chiudere, girare in senso orario.

Important

Gasket

Must be in

place

Secure with ¼” Allen wrench.

• Asegure con la llave Allen del ¼”.

• Fixez clé Allen avec de ¼”.

• Sichern Sie mit ¼“ Inbusschlüssel.

• Fixe com chave Allen do ¼ de”.

• Fissi con chiave di Allen del ¼”.

To loosen - unscrew bolts ½” turn counter

clockwise.

• Para aflojar - desatornille a la derecha contrario de la vuelta

del ½ de los pernos”.

• Pour se desserrer - dans le sens des aiguilles d'une montre de

tour dévissez de boulons ½ » contre-.

• Um sich zu lösen - schrauben Sie Schraubbolzen ½“

Umdrehungs-Gegenrechtses herum ab.

• Para afrouxar - desaparafuse sentido horário contrário volta

do ½ dos parafusos da”.

• Per allentare - sviti in senso orario di girata del ½ dei bulloni„

contro.

1 12VDC+ Red

2 12VDC- Black

12VDC Power leads RM7F2N

WIRING INSIDE HOUSING

Camera power supply

DC power for camera

(red & black wires)

The beam angle may be adjusted on the

bottom of the unit.

• Instale la cámara fotográfica en el soporte fijo y termine

todos los usos del cableado.

• Installez l'appareil-photo sur la parenthèse fixe et accom-

plissez toutes les applications de câblage.

• Bringen Sie die Kamera am örtlich festgelegten Haltewin-

kel an und führen Sie alle Verdrahtung Anwendungen

durch.

• Instale a câmera no suporte fixo e termine todas as

aplicações da fiação.

• Installi la macchina fotografica sulla staffa fissa e completi

tutte le applicazioni dei collegamenti.

Install the camera on the fixed bracket and

complete all wiring applications.

RJ45

BNC

24VAC

Camera

Heater/Blower

Red

Orange

Yellow

Green

POWER

27 Watts (MAX)

52 Watts

1/0

Alarm 1

Alarm 2

Alarm 3

Common

Blue

Violet

Gray

White

Make the appropriate male and female connections. Indoor model does not include pre-run cables.

• Haga las conexiones masculinas y femeninas apropiadas. El modelo de interior no incluye pre-funciona los cables.

• Établissez les rapports masculins et femelles appropriés. Le modèle d'intérieur n'inclut pas pré-courent des câbles.

• Stellen Sie die passenden männlichen und weiblichen Beziehungen her. Innenmodell schließt nicht vor-laufen lassen Kabel

ein.

• Faça as conexões masculinas e fêmeas apropriadas. O modelo indoor não inclui pre-funciona cabos.

• Faccia i collegamenti maschii e femminili adatti. Il modello dell'interno non include pre-fa funzionare i cavi.

Wire Gauge

Total vA

consumed

,75

1,0

1,5

2,5

AWG

5.5

400

121

600

182

960

292

- - -

120

36.5

180

54.9

300

91.4

480

146

800

243

1300

396

27.1

141

43.0

225

68.6

358

109

571

174

905

275

1440

438

19.8

27.4

130

39.6

225

68.6

350

106

525

160

830

252

13.4

21.3

112

34.1

179

54.6

285

86.9

452

138

720

219

10.6

17.1

27.4

143

43.6

228

69.5

362

110

576

175

9.4

14.3

22.9

119

36.2

190

57.9

301

91.7

480

146

8.8

12.2

19.5

102

31.1

163

49.7

258

78.6

411

125

7.6

10.3

16.8

25.9

140

42.7

215

65.5

340

103

These are recommended maximum distances

for 24VAC with a 10% voltage drop.

• Éstos se recomiendan las distancias máximas para

24VAC con una caída de voltaje del 10%.

• Ceux-ci sont recommandés des distances maximum

pour 24VAC avec une chute de tension de 10%.

• Diese werden maximale Abstände für 24VAC mit

einem 10% Spannungsabfall empfohlen.

• Estes são recomendados distâncias máximas para

24VAC com uma queda de tensão de 10%.

• Questi sono suggeriti distanze massime per 24VAC con

una differenza de potenziale di 10%.

Power supply

only included with

network 24V models





Align the arrows on the outside of the dome

and lock.

• Alinee las flechas en el exterior de la bóveda y

trábese.

• Alignez les flèches sur l'extérieur du dôme et

fermez à clef.

• Richten Sie die Pfeile auf der Außenseite der

Haube aus und verriegeln Sie sich.

• Alinhe as setas na parte externa da abóbada e

trave-as.

• Allinei le frecce sulla parte esterna della cupola e

blocchi.

Wipe the dome clean. Please follow the proper

cleaning procedure

• Limpie la cúpula limpio. Por favor, siga el procedimiento de

limpieza adecuado, como se muestra

• Essuyez le dôme propre. S'il vous plaît suivre la procédure de

nettoyage, comme indiqué

• Wischen Sie die Kuppel reinigen. Bitte beachten Sie die

ordnungsgemäße Reinigung Verfahren

• Limpe a cúpula limpo. Por favor, siga o procedimento

adequado de limpeza conforme

• Pulire la cupola pulito. Si prega di seguire la corretta

procedura di pulizia, come

Tab

Connect Lanyard to trim ring assembly.

• Conecte el acollador con el montaje del anillo del

ajuste.

• Reliez la lanière à l'anneau d'équilibre.

• Schließen Sie Abzuglinie an Ordnung Ring an.

• Conecte o colhedor ao conjunto do anel da

guarnição.

• Colleghi la cordicella al complessivo dell'anello

della cornice.

Fasten down the dome with a Phillips screwdriver.

• Sujete abajo de la bóveda con un destornillador Phillips.

• Attachez en bas du dôme avec un tournevis Phillips.

• Befestigen Sie sich hinunter die Haube mit einem Kreuzkopf-

schraubenzieher.

• Prenda abaixo a abóbada com uma chave de fenda Phillips.

• Fissisi giù la cupola con un cacciavite "phillips".

Replacement Parts List

RHW75CF2N

(1)

(2)

Part Description

N/S

RPRH7502

RPRH7503

RC7T

RC7C

RPFD072

RPFD080

RPRH707

(Model RH7NHB)

RPRH708

RPFD040

RPRH709

RPFD2612

WM10

RPRH713

SD0170

SD0180

RPPKE1100

RPPKH2100

RPPKE1125

RPTRANS100

LOWER TRIM RING

DOME CLAMPING

BRACKET

TINTED REPLACEMENT

CAPSULE

CLEAR REPLACEMENT

CAPSULE

24 VAC HEATER

(12 VDC) BLOWER (USED

IN 24V HOUSING)

CONNECTION PCB

(NETWORK MODELS)

CAMERA BRACKET

UPPER BRACKET

ASSEMBLY

HOUSING TOP

HOUSING TOP-GASKET

WM10 WALL MOUNT

FIXED CAMERA BRACKET

PENDANT HOUSING

COUPLING

QUICK RELEASE PIPE

COUPLING

ELECTRICAL PACKET

HOUSING HARDWARE

PACKET C- SECURITY

SCREWS

ELECTRICALPACKET,HB,

FIXED NETWORK

96VA TRANSFORMER

IRHW75CF2N

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles,

Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.

Take a few moments and validate your purchase via the Online Product Registration Form at

www.videolarm.com/productregistration.jsp

• Simple and Trouble-Free RMA process

• Added into customer database to receive product updates / news

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…