Sharp AY-XPC9JR Manuale del proprietario

SPLIT TYPE

ROOM AIR CONDITIONER

OPERATION MANUAL

ENGLISH

ACONDICIONADOR DE AIRE

DE DOBLE SERVICIO

MANUAL DE INSTRUCCIONES

CONDIZIONATORE D'ARIA

DA CAMERA TIPO SPLIT

MANUALE DI ISTRUZIONI

ZWEITEILIGES

KLIMAGERÄT

BEDIENUNGSANLEITUNG

CLIMATISEUR INDIVIDUEL

EN DEUX PARTIES

MODE D'EMPLOI

FRANÇAIS

ESPAÑOL

ITALIANO

DEUTSCH

EΛΛΗΝΙΚΑ

ΑΙΡΚΟΝΤΙΣΙΟΝ ΔΩΜΑΤΙΟΥ

ΤΥΠΟΥ SPLIT

ΕΓΧΕΙΡΙΔΙΟ ΛΕΙΤΟΥΡΓΙΑΣ

PORTUGUÊS

AR CONDICIONADO DE SALA

DE DUAS UNIDADES

MANUAL DE OPERAÇÃO

INDOOR UNIT

AY-XPC7JR

AY-XPC9JR

AY-XPC12JR

Device of this mark is a trademark of

Sharp Corporation.

Plasmacluster is a registered trademark

or a trademark of Sharp Corporation.

Attention: Your product is

marked with this symbol. It

means that used electrical and

electronic products should

not be mixed with general

household waste. There is a

separate collection system for

these products.

A. Information on Disposal for Users (private households)

1. In the European Union

Attention: If you want to dispose of this equipment, please do not use the

ordinary dust bin!

Used electrical and electronic equipment must be treated separately and

in accordance with legislation that requires proper treatment, recovery and

recycling of used electrical and electronic equipment.

Following the implementation by member states, private households within

the EU states may return their used electrical and electronic equipment

to designated collection facilities free of charge*. In some countries* your

local retailer may also take back your old product free of charge if you

purchase a similar new one.

*) Please contact your local authority for further details.

If your used electrical or electronic equipment has batteries or

accumulators, please dispose of these separately beforehand according to

local requirements.

By disposing of this product correctly you will help ensure that the waste

undergoes the necessary treatment, recovery and recycling and thus

prevent potential negative effects on the environment and human health

which could otherwise arise due to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and

ask for the correct method of disposal.

For Switzerland: Used electrical or electronic equipment can be returned

free of charge to the dealer, even if you don’t purchase a new product.

Further collection facilities are listed on the homepage of www.swico.ch or

www.sens.ch.

B. Information on Disposal for Business Users.

1. In the European Union

If the product is used for business purposes and you want to discard it:

Please contact your SHARP dealer who will inform you about the take-back

of the product. You might be charged for the costs arising from take-back

and recycling. Small products (and small amounts) might be taken back by

your local collection facilities.

For Spain: Please contact the established collection system or your local

authority for take-back of your used products.

2. In other Countries outside the EU

If you wish to discard of this product, please contact your local authorities

and ask for the correct method of disposal.

The battery supplied with this product contains traces of Lead.

For EU: The crossed-out wheeled bin implies that used batteries should

not be put to the general household waste! There is a separate collection

system for used batteries, to allow proper treatment and recycling in

accordance with legislation. Please contact your local authority for details

on the collection and recycling schemes.

For Switzerland: The used battery is to be returned to the selling point.

For other non-EU countries: Please contact your local authority for correct

method of disposal of the used battery.

GB

P

b

Contains ﬂ uorinated greenhouse gases covered by the Kyoto Protocol

R410A (Global warming potential 1980)

GB-1

ENGLISH

Please read this manual carefully before using the product.

This manual should be kept in a safe place for handy reference.

WARNINGS FOR INSTALLATION/

REMOVAL/REPAIR

• Do not attempt to install/remove/repair the unit by

yourself. Incorrect work will cause electric shock,

water leak, ﬁ re etc. Consult your dealer or other

qualified service personnel for the installation/

removal/repair of the unit.

CAUTIONS FOR USE

1

Open a window or door periodically to ventilate

the room, especially when using gas appliances.

Insufficient ventilation may cause oxygen

shortage.

2

Do not operate the buttons with wet hand. It

may cause electric shock.

3

For safety, turn the circuit breaker off when not

using the unit for an extended period of time.

4

Check the outdoor unit mounting rack

periodically for wear and to make sure it is ﬁ rmly

in place.

5

Do not put anything on the outdoor unit nor step

on it. The object or the person may fall down or

drop, causing injury.

6

This unit is designed for residential use. Do not

use for other applications such as in a kennel or

greenhouse to raise animals or grow plants.

7

Do not place a vessel with water on the unit.

If water penetrates into the unit, electrical

insulations may deteriorate and cause electric

shock.

8

Do not block the air inlets nor outlets of the

unit. It may cause insufﬁ cient performance or

troubles.

9

Be sure to stop the operation and turn the circuit

breaker off before performing any maintenance

or cleaning. A fan is rotating inside the unit and

you may get injured.

10

This appliance is not intended for use by young

children or inﬁ rm persons without supervision.

Young children should be supervised to ensure

that they do not play with the appliance.

CAUTIONS FOR LOCATION/

INSTALLATION

• Make sure to connect the air conditioner to power

supply of the rated voltage and frequency.

Use of a power supply with improper voltage and

frequency can result in equipment damage and

possible ﬁ re.

• Do not install the unit in a place where inﬂ am-

mable gas may leak. It may cause ﬁ re.

Install the unit in a place with minimal dust, fumes

and moisture in the air.

• Arrange the drain hose to ensure smooth drain-

age. Insufﬁ cient drainage may cause wetting of the

room, furniture etc.

• Make sure a leak breaker or a circuit breaker is

installed, depending on the installation location, to

avoid electrical shock.

IMPORTANT SAFETY

INSTRUCTIONS

WARNINGS FOR USE

1

Do not pull or deform the power supply cord.

Pulling and misuse of the power supply cord

can result in damage to the unit and cause

electrical shock.

2

Be careful not to expose your body directly to

the outlet air for a long time. It may affect your

physical conditions.

3

When using the air conditioner for infants,

children, elderly, bedridden, or disabled people

make sure the room temperature is suitable for

those in the room.

4

Never insert objects into the unit. Inserting

objects can result in injury due to the high

speed rotation of internal fans.

5

Ground the air conditioner without fail. Do not

connect the grounding wire to gas pipe, water

pipe, lightning rod or telephone grounding

wire. Incomplete grounding may cause electric

shock.

6

If anything is abnormal with the air conditioner

(ex. a burning smell), stop the operation

immediately and turn the circuit breaker OFF.

7

The appliance shall be installed in accordance

with national wiring regulations.

Improper cable

connection can cause the power supply cord,

plug and the electrical outlet to overheat and

cause ﬁ re.

8

If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualiﬁ ed person in order

to avoid a hazard. Use only the manufacture-

speciﬁ ed power cord for replacement.

9

Do not splash or pour water directly on the unit.

Water can cause electrical shock or equipment

damage.

ENGLISH

• IMPORTANT SAFETY INSTRUCTIONS ......GB-1

• PART NAMES ...............................................GB-2

• USING THE REMOTE CONTROL ...............GB-4

• SETTING AIR PURIFYING FILTER ............GB-5

• TIPS ON SAVING ENERGY .........................GB-5

• AUXILIARY MODE .......................................GB-5

• BASIC OPERATION .....................................GB-6

• ADJUSTING THE AIR FLOW DIRECTION ..GB-7

• PROGRESSIVE AIRFLOW ..........................GB-8

• FULL POWER OPERATION ........................GB-8

• PLASMACLUSTER OPERATION ................GB-9

• SELF CLEAN OPERATION ..........................GB-9

• ONE-HOUR OFF TIMER ..............................GB-10

• TIMER OPERATION ....................................GB-10

• TIPS ABOUT INDICATOR PANEL ................GB-12

• MAINTENANCE ...........................................GB-12

• ADDITIONAL NOTES ON OPERATION ......GB-13

• BEFORE CALLING FOR SERVICE .............GB-14

CONTENTS

GB-2

PART NAMES

INDOOR UNIT

1 AUX Button

2 Inlet (Air)

3 Open Panel

4 Air Purifying Filter

5 Air Filters

6 Receiver Window

7 Vertical Adjustment Louvre

8 Horizontal Adjustment Louvre

9 Outlet (Air)

10 Remote Control

11 PLASMACLUSTER Lamp (blue)

12 TEMPERATURE INDICATOR

13 OUTDOOR Temp. Lamp (green

)

14 ROOM Temp. Lamp (green )

15 FULL POWER Lamp (green

)

16 TIMER Lamp (orange )

17 OPERATION Lamp (red

)

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

NOTE:

Actual units might vary slightly from those shown above.

GB-3

ENGLISH

REMOTE CONTROL

1 TRANSMITTER

2 DISPLAY (Liquid Crystal Display)

3 PLASMACLUSTER Button

4 DISPLAY Button

5 ON/OFF Button

6 THERMOSTAT Button

7 FULL POWER Button

8 PROGRESSIVE AIRFLOW Button

9 MODE Button

10 TIMER ON Button (for setting the timer)

11 TIMER OFF Button (for setting the timer)

12 ONE-HOUR OFF TIMER Button

13 TIME ADVANCE Button

14 TIME REVERSE Button

15 SELF CLEAN Button

16 TIMER SET/CANCEL Button

17 Indicates battery compartment is below this mark

18 CLOCK Button

19 FAN Button

20 SWING Button

L.C.D. REMOTE CONTROL DISPLAY

21 PROGRESSIVE AIRFLOW Symbol

22 SELF CLEAN Symbol

23 PLASMACLUSTER Symbol

24 MODE Symbols

: AUTO : COOL

: HEAT : DRY

25 Thermostat setting for AUTO and DRY modes

26 TEMPERATURE Indicator

27 TRANSMITTING Symbol

28 FULL POWER Symbol

29 FAN SPEED Symbols

: AUTO : LOW

: HIGH : SOFT

30 TIMER ON Indicator/CLOCK

Indicates the on timer preset time or current time.

31 TIMER OFF Indicator

Indicates the preset time for off timer or one-hour off

timer.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

GB-4

SET CURRENT CLOCK TIME

There are two clock modes: 12-hour mode and

24-hour mode.

Example: 5 o’clock in the afternoon

Clock Display

12-hour mode PM 5:00

24-hour mode 17:00

1

To set to the 12-hour mode, press the

CLOCK button once in the ﬁ rst step.

To set to the 24-hour mode, press the

CLOCK button twice in the ﬁ rst step.

2

Press the TIME ADVANCE or REVERSE

button to set the current time.

• Keep the button pressed to advance or

reverse the time display quickly.

3

Press the SET/C button.

• The colon (:) blinks to indicate that the clock

is functioning.

NOTE:

• The current time cannot be set when the timer is

operating.

LOADING BATTERIES

Use two size-AAA (R03) batteries.

1

Remove the remote control cover.

2

Insert batteries in the compartment,

making sure the (+) and (

-

) polarities

are correctly a lign ed.

• The display indicates “AM 6:00” when

batteries are properly installed.

3

Reinstall the cover.

Remote

control cover

NOTE:

• The battery life is approximately one year in

normal use.

• When you replace the batteries, always change

both batteries, and make sure they are the same

type.

• If the remote control does not operate properly

after replacing the batteries, take out the batteries

and reinstall them again after 30 seconds.

• If you will not be using the unit for a long time,

remove the batteries from the remote control.

HOW TO USE THE REMOTE CONTROL

Point the remote control towards the unit’s signal

receiver window and press the desired button. The

unit generates a beep when it receives the signal.

• Make sure there is no curtain or other object

between the remote control and the unit.

• The remote control can send signals from up to 7

metres away.

CAUTION:

• Do not allow the signal receiver window to receive

strong direct sunlight, since it can adversely affect

its operation. If the signal receiver window is

exposed to direct sunlight, close a curtain to block

the light.

• Using a ﬂ uorescent lamp with a quick starter in

the same room may interfere with transmission of

the signal.

• The unit can be affected by signals transmitted

from the remote control of a television, VCR or

other equipment used in the same room.

• Do not leave the remote control in direct sunlight

or near a heater. Also, protect the unit and remote

control from moisture and shock which can

discolour or damage them.

USING THE REMOTE CONTROL

2

3

1

GB-5

ENGLISH

The air purifying filters are packed as

accessory of this unit. During operation of the

air conditioner, the filters remove dust and

tobacco smoke from the air and discharges

clean air.

1

Take out the air ﬁ lters.

1

Open the open panel.

2

Push the air filters up slightly to unlock

them.

3

Pull the air ﬁ lters down to remove them.

2

Set the air purifying ﬁ lter under the ﬁ lter

stoppers located on the air ﬁ lter.

3

Reinstall the air ﬁ lters.

1

Reinstall the air ﬁ lters in the original posi-

tions.

2

Close the open panel.

3

Push the arrow-marked of the panel ﬁ rmly

to lock it in place.

Precautions:

• The ﬁ lters are sealed in a plastic bag to keep their

dust collection effect.

Do not open the bag until using the filters.

(Otherwise the ﬁ lters life may get shorter.)

• Do not expose the filters to direct sunlight.

(Otherwise they may deteriorate.)

TIPS ON SAVING ENERGY

Below are some simple ways to save energy

when you use your air conditioner.

SET THE CORRECT TEMPERATURE

• Setting the thermostat 1°C higher than the desired

temperature in the COOL mode and 2°C lower

in the HEAT mode will save approximately 10

percent in power consumption.

• Setting the temperature lower than necessary

during cooling operation will result in increased

power consumption.

BLOCK DIRECT SUNLIGHT AND PREVENT

DRAFTS

• Blocking direct sunlight during cooling operation

will reduce power consumption.

• Close the windows and doors during cooling and

heating operations.

SET PROPER AIR FLOW DIRECTION TO OBTAIN

THE BEST AIR CIRCULATION

KEEP FILTER CLEAN TO ENSURE THE MOST

EFFICIENT OPERATION

MAKE MOST OF THE TIMER OFF FUNCTION

DISCONNECT THE POWER CORD WHEN THE

UNIT IS NOT USED FOR AN EXTENDED PERIOD

OF TIME

• The indoor unit still consumes a small amount of

power when it is not operating.

AUXILIARY MODE

Use this mode when the remote control is not

available.

TO TURN ON

Lift the open panel of the indoor unit and press

the AUX. button.

• The red OPERATION lamp ( ) on the unit will

light and the unit will start operating in the AUTO

mode.

• The fan speed and temperature setting are set to

AUTO.

TO TURN OFF

Press the AUX. button again.

• The red OPERATION lamp ( ) on the unit will

turn off.

NOTE:

• If the AUX button is pressed during normal

operation, the unit will turn off.

SETTING AIR PURIFYING

FILTER

Filter stopper

Air purifying ﬁ lter

Air ﬁ lter

3

1

2

3

1

2

AUX

GB-6

1

Press the MODE button to select the

operation mode.

AUTO HEAT COOL DRY

2

Press the ON/OFF button to start

operation.

• The red OPERATION lamp ( ) on the unit

will light.

3

Press the THERMOSTAT button to set

the desired temperature.

AUTO/DRY MODE

• The temperature can be changed in 1°C incre-

ments within the range of 2°C higher to 2°C

lower from the temperature automatically deter-

mined by the air conditioner.

COOL/HEAT MODE

• The temperature can be set within the

range of 18 to 32°C.

4

Press the FAN button to set the desired

fan speed.

AUTO SOFT LOW HIGH

• In the DRY mode, the fan speed is preset to

AUTO and cannot be changed.

5

To turn off the unit, press the ON/OFF

button again.

• The red OPERATION lamp ( ) on the unit

will turn off.

BASIC OPERATION

(Example: 1°C higher)

C

(Example: 2°C lower)

C

2

5

3

1

4

GB-7

ENGLISH

VERTICAL AIR FLOW DIRECTION

1

Press the SWING button on the remote

control once.

• The vertical adjustment louvres will swing

continuously.

2

Press the SWING button again when the

vertical adjustment louvres are at the

desired position.

Adjustment range

COOL and DRY modes

HEA

T mode

HORIZONTAL AIR FLOW DIRECTION

NOTE:

• The adjusted position will be memorized and will

be automatically set to the same position when

operated the next time.

1

2

ADJUSTING THE AIR FLOW

DIRECTION

CAUTION:

Never attempt to adjust the vertical adjustment lou-

vres manually.

• Manual adjustment of the vertical adjustment lou-

vre can cause the unit to malfunction when the

remote control is used for adjustment.

• When the vertical adjustment louvre is positioned

at the lowest position in the COOL or DRY mode

for an extended period of time, condensation may

result.

Do not adjust the horizontal adjustment louvre to the ex-

treme left or right in the COOL mode with the fan speed

set to “SOFT (

)” for an extended period of time.

Condensation may form on the louvres.

Hold the horizontal adjustment louvre as shown

in the diagram and adjust the air ﬂ ow direction.

When using your air-condi-

tioner with multi-system

With a multi system air conditioner, mul-

tiple indoor units can be connected to

one outdoor unit. When the setting mode

differs among indoor unit(s), the indoor

unit(s) operated later may not work.

• When the indoor unit(s) is/are operating in

HEAT mode, the remaining unit(s) can not

operate in COOL or DRY mode.

• When the indoor unit(s) is/are operating in

COOL or DRY mode, the remaining unit(s)

can not operate in HEAT mode.

When the mode of the indoor unit(s) later op-

erated is/are different from those which is/are

in operation, after a few seconds, a long BEEP

will be emitted and the temperature indicator

on the indicator panel will indicate”

” and

the OPERATION lamp and TIMER lamp will

blink alternately. This shows that the later op-

erated unit(s) is/are not working. In such case,

change the mode to the same mode which the

other indoor unit(s) is/are operating in.

TIPS ABOUT AUTO MODE

In the AUTO mode, the temperature setting

and mode are automatically selected accord-

ing to the room temperature and outdoor

temperature when the unit is turned on.

• During operation, if the outdoor tempera-

ture changes, the temperature settings will

automatically slide as shown in the chart.

Modes and Temperature Settings

The ﬁ gures in ( ) are temperature settings

• When using your air-conditioner with multi-

system, mode of the unit operated first

will have priority over other unit(s) without

reference to the above chart.

GB-8

Press the PROGRESSIVE AIRFLOW button

during cooling or dry operation when you do not

want to feel cold air. Vertical adjustment louvre

is set obliquely upward to deliver cool air to the

ceiling.

Press the button during heating operation.

Vertical adjustment louvre is set downward to

deliver the warm air down to the ﬂ oor and warm

you.

1

During operation, press the

PROGRESSIVE AIRFLOW button.

• The remote control will display “ ”.

TO CANCEL

Press the PROGRESSIVE AIRFLOW button

again.

NOTE:

• The PROGRESSIVE AIRFLOW setting is

cancelled when you press FULL POWER button

while PROGRESSIVE AIRFLOW is set.

• If you want PROGRESSIVE AIRFLOW operation

in FULL POWER mode, press PROGRESSIVE

AIRFLOW button during FULL POWER operation.

In this operation, the air conditioner works at the

maximum power to makes the room cool or warm

so rapidly that you can use it just after you come

home.

1

To activate the FULL POWER operation,

press the FULL POWER button during

operation.

• The remote control will display “ ”.

• The temperature display will go off.

• The green FULL POWER lamp ( ) on

the unit will light up.

TO CANCEL

Press the FULL POWER button again.

• FULL POWER operation will also be cancelled

when the operation mode is changed, or when the

unit is turned off.

• The green FULL POWER lamp (

) on the unit

will turn off.

NOTE:

• You can not set the temperature or fan speed

during the FULL POWER operation.

PROGRESSIVE AIRFLOW

FULL POWER OPERATION

1

GB-9

ENGLISH

PLASMACLUSTER OPERATION

The Plasmacluster Ion generator inside the air

conditioner will release positive and negative

plasmacluster ions into the room.

Approximately the same numbers of positive

and negative ions released into the air will

reduce some airborne mold.

1

During operation, press the

PLASMACLUSTER button.

• The remote control will display “ ”.

• The blue PLASMACLUSTER lamp on the

unit will light up.

TO CANCEL

Press the PLASMACLUSTER button again.

• The PLASMACLUSTER lamp on the unit will turn

off.

NOTE:

• Use of the PLASMACLUSTER operation will be

memorized, and it will be activated the next time

you turn on the air conditioner.

• To turn off the PLASMACLUSTER lamp, press

the DISPLAY button.

• To perform the PLASMACLUSTER operation

without accompanying heat, cool or dry mode,

press the PLASMACLUSTER button while the

unit is not operating. The mode symbol of the

remote control will go off and the fan speed can

not be set AUTO.

SELF CLEAN OPERATION

SELF CLEAN operation will reduce the growth

mold fungus with Plasmacluster ions, and dry

inside of the air conditioner unit. Utilize the

operation at seasonal change over terms.

Mold fungus already grown can not be eliminated

by this operation.

1

Press the SELF CLEAN button when the

unit is not operating.

• The remote control displays “ ”.

• The blue PLASMACLUSTER lamp on the unit

will light up.

• The unit will stop operation after forty

minutes.

• The remaining operation time will be indicated

on the TEMPERATURE INDICATOR of the

indoor unit in minute decrements.

TO CANCEL

Press the SELF CLEAN button.

Alternatively, turn the unit off by pressing the

ON/OFF button.

• The blue PLASMACLUSTER lamp on the unit will

turn off.

NOTE:

• You cannot set the temperature, fan speed, air

ﬂ ow direction or timer setting during the SELF

CLEAN operation.

1

GB-10

ONE-HOUR OFF TIMER

When the ONE-HOUR OFF TIMER is set, the unit

will automatically turn off after one hour.

1

Press the ONE-HOUR OFF TIMER

button.

• The remote control displays “ ”.

• The orange TIMER lamp (

) on the unit will

light up.

• The unit will stop operating after one hour.

TO CANCEL

Press the TIMER CANCEL (SET/C) button.

• The orange TIMER lamp ( ) on the unit will

turn off.

Alternatively, turn the unit off by pressing the

ON/OFF button.

• The red OPERATION lamp (

) and the

orange TIMER lamp ( ) on the unit will turn off.

NOTE:

• The ONE-HOUR OFF TIMER operation has

priority over TIMER ON and TIMER OFF

operations.

• If the ONE-HOUR OFF TIMER is set while the

unit is not operating, the unit will operate for an

hour at the formerly set condition.

• If you wish to operate the unit for another hour

before the ONE-HOUR OFF TIMER is activated,

press the ONE-HOUR OFF TIMER button again

during operation.

• If TIMER ON and/or TIMER OFF are set, TIMER

CANCEL button cancels every setting.

TIMER OPERATION

TIMER OFF

1

Press the TIMER OFF ( ) button.

2

The TIMER OFF indicator will blink;

press the TIME ADVANCE or REVERSE

button to set the desired time.

(The time can be set in 10-minute increments.)

3

Point the remote control at the receiver

window on the unit and press the TIMER

SET (SET/C) button.

• The orange TIMER lamp ( ) on the unit will

light.

• The unit will generate a beep when it receives

the signal.

TIPS ABOUT TIMER OFF OPERATION

When the TIMER OFF mode is set, the temperature

setting is automatically adjusted to prevent the room

from be coming excessively hot or too cold while you

sleep. (Auto Sleep function)

COOL/DRY MODE:

• One hour after the time operation begins, the

temperature setting rises 1°C higher than the

original temperature setting.

HEAT MODE:

• One hour after the timer operation begins, the

temperature setting drops 3°C lower than the

original temperature setting.

1

2

3

1

CANCEL

GB-11

ENGLISH

TIMER ON

1

Press the TIMER ON ( ) button.

2

The TIMER ON indicator will blink;

press the TIME ADVANCE or REVERSE

button to set the desired time

.

(The time can be set in 10-minute increments.)

3

Point the remote control at the receiver

window on the unit and press the

TIMER SET (SET/C) button.

• The orange TIMER lamp ( ) on the unit will

light.

• The unit will generate a beep when it receives

the signal.

4

Select the operation condition.

NOTE:

• The unit will turn on prior to the set time to allow

the room to reach the desired temperature by the

programmed time. (Awaking function)

COMBINED USE OF ON AND OFF

TIMERS

You can use the ON and OFF timers in

combination.

Example:

To stop operation at 11:00 p.m. and resume

operation to bring the room temperature to the

desired level by 7:00 a.m.

1

Set the TIMER OFF to 11:00 p.m. during

operation.

2

Set the TIMER ON to 7:00 a.m.

The arrow ( or ) between the TIMER ON

indicator and the TIMER OFF indicator shows

which timer will activate ﬁ rst.

NOTE:

• You cannot programmed the ON-TIMER and

OFF-TIMER to operate the unit at different

temperatures or other settings.

• Either timer can be programmed to activate prior

the other.

TO CANCEL TIMER MODE

Press the TIMER CANCEL (SET/C) button.

• The orange TIMER lamp (

) on the unit will turn

off.

•

The current clock time will be displayed on the

remote control.

NOTE:

• If any TIMER ON, TIMER OFF and ONE-HOUR

OFF TIMER are set, the TIMER CANCEL button

cancels all settings.

TO CHANGE TIME SETTING

Cancel the TIMER setting ﬁ rst, then set it again.

1

2

3

Before setting the timer, make sure the clock is properly set with the current time.

CANCEL

GB-12

MAINTENANCE

Be sure to disconnect the power cord from the

wall outlet or turn off the circuit breaker before

performing any maintenance.

CLEANING THE FILTERS

The air ﬁ lters should be cleaned every two weeks.

1

Turn off the unit.

2

Remove the ﬁ lters.

1

Lift the open panel.

2

Push the air filters up slightly to unlock

them.

3

Pull the air ﬁ lters down to remove them.

3

Take off the air purifying ﬁ lters from the

air ﬁ lters.

4

Clean the ﬁ lters.

Use a vacuum cleaner to remove dust. If the

ﬁ lters are dirty, wash them with warm water and

a mild detergent. Dry ﬁ lters in the shade before

reinstalling.

5

Reinstall the air purifying ﬁ lters.

6

Reinstall the ﬁ lters.

1

Reinstall the ﬁ lters in the original positions.

2

Close the open panel.

3

Push the arrow-marked of the panel ﬁ rmly

to lock it in place.

CLEANING THE UNIT AND THE

REMOTE CONTROL

• Wipe them with a soft cloth.

• Do not directly splash or pour water on them. It

can cause electrical shock or equipment damage.

• Do not use hot water, thinner, abrasive powders or

strong solvents.

3

1

2

3

1

2

TIPS ABOUT INDICATOR

PANEL

The indicator panel will change each time

you press the DISPLAY button in the fol-

lowing manner.

NOTES:

• The displayed temperatures are rough estimates

and may vary from the actual temperatures.

• Temperature display ranges

Room temperature: 0°C ~ 40°C (

is displayed

when less than 0°C and

when higher than 40°

C)

Outdoor temperature: –9°C ~ 45°C ( is

displayed when less than –9°C and when

higher than 45°C)

•

is displayed during the first about 0~120

seconds of operation while the temperatures are

being detected.

• During SELF CLEAN operation, the indicator

panel will display remaining time of the operation.

Room and outdoor temperature will not be

displayed even if you press the DISPLAY button.

Single use

• Only the room temperature can be displayed for 5

seconds when the unit is not in operation.

Multi use

• is displayed for 5 seconds when the unit is not

in operation.

The room

temperature is

displayed

.

The outdoor

temperature is

displayed.

No display.

GB-13

ENGLISH

INDOOR TEMP.

OUTDOOR TEMP.

COOLING

upper limit 32˚C

46˚C (Single use)

43˚C (Multi use)

lower limit 21˚C

–10˚C (Single use)

21˚C (Multi use)

HEATING

upper limit 27˚C 24˚C

lower limit – –15˚C

• The built-in protective device may prevent the unit

from operating when used out of this range.

• Condensation may form on the air outlet if the unit

operates continuously in the COOL or DRY mode

when humidity is over 80 percent.

WHEN POWER FAILURE OCCURS

This air conditioner has a memory function to store

settings when a power failure occurs.

After power recovery, the unit will automatically re-

start in the same settings which were active before

the power failure, except for timer settings.

If the timers were set before a power failure, they

will need to be re-set after power recovery.

PREHEATING FUNCTION

In the HEAT operation, the indoor fan may not start

for two to ﬁ ve minutes after the unit is turned on to

prevent cold air from blowing out of the unit.

DE-ICING FUNCTION

• When ice forms on the heat exchanger in the

outdoor unit during the HEAT operation, an

automatic de-icer provides heat for about 5 to 10

minutes to remove the ice. During de-icing, the

inside and outside fans stop operating.

• After de-icing is completed, the unit automatically

resumes operation in the HEAT mode.

HEATING EFFICIENCY

• The unit employs a heat pump that draws heat

from the outside air and releases it into the room.

The outside air temperature therefore greatly

affects the heating efﬁ ciency.

• If the heating efﬁ ciency is reduced due to low

outside temperatures, use an additional heater.

• It takes time to warm up and heat the entire room

because of the forced air circulation system.

MAINTENANCE AFTER AIR

CONDITIONER SEASON

1

Operate the unit in the SELF CLEAN

operation to allow the mechanism to

thoroughly dry.

2

Stop the operation and unplug the unit.

Turn off the circuit breaker, if you have

one exclusively for the air conditioner.

3

Clean the ﬁ lters, then reinstall them.

MAINTENANCE BEFORE AIR

CONDITIONER SEASON

1

Make sure that the air ﬁ lters are not

dirty.

2

Make sure that nothing obstructs the

air inlet or outlet.

CHANGING THE AIR PURIFYING

FILTER

The ﬁ lters should be changed every 3 ~ 6 months

1

Remove the air ﬁ lters.

2

Change the air purifying ﬁ lters.

1

Take off the old air purifying ﬁ lters from the

air ﬁ lters.

2

Set the new air purifying ﬁ lters, under the

ﬁ lter stoppers located on the air ﬁ lters.

3

Reinstall the air ﬁ lters.

NOTE:

• The dirty air purifying ﬁ lters are not washable

for reuse. The new ﬁ lters are available at your

nearest dealer.

Replacement ﬁ lter: Type AZ-F920F

Disposal of Filters

Please dispose of replaced ﬁ lters according to the

local disposal laws and regulations.

AIR PURIFYING ﬁ lter materials

Filter:Polypropylene

Frame:Polyester

Filter stopper

ADDITIONAL NOTES ON

OPERATION

OPERATING TEMPERATURE RANGE

GB-14

BEFORE CALLING FOR SERVICE

The following conditions do not denote equip-

ment malfunctions

UNIT DOES NOT OPERATE

The unit will not operate if it is turned on immediately

after it is turned off. The unit will not operate

immediately after the mode is changed. This is to

protect the internal mechanisms. Wait 3 minutes

before operating the unit.

UNIT DOES NOT SEND OUT WARM AIR

The unit is preheating or de-icing.

ODORS

Carpet and furniture odors that entered into the unit

may be sent out from the unit.

CRACKING NOISE

The unit may produce a cracking noise. This sound

is generated by the friction of the front panel and

other components expanding or connecting due to a

temperature change.

A LOW BUZZING NOISE EMITTED

This is a sound emitted when the unit is generating

Plasmacluster ions.

SWISHING NOISE

The soft, swishing noise is the sound of the refrigerant

ﬂ owing inside the unit.

WATER VAPOUR

• In the COOL and DRY operation, water vapour

can sometimes be seen at the air outlet due to the

difference between the room air temperature and

the air discharged by the unit.

• In the HEAT operation, water vapour may ﬂ ow out

of the outdoor unit during de-icing.

THE OUTDOOR UNIT DOES NOT STOP

After stopping the operation, the outdoor unit will rotate

its' fan for about a minute to cool down the unit.

ODOR EMITTED FROM THE PLASMACLUSTER

AIR OUTLET

This is the smell of ozone generated from the

Plasmacluster Ion generator. The ozone concentration

is very small, posing no adverse effect on your health.

The ozone discharged into the air rapidly decomposes,

and its density in the room will not increase.

When using your air conditioner with multi-

system

INDOOR UNIT BECOMES WARM EVEN WHEN

IDLE

This is because the refrigerant also ﬂ oes through the

idle indoor unit's pipes when the other unit is operated

in HEAT mode.

INDOOR UNIT BECOMES WARM EVEN WHEN

NOT DURING HEATING OPERATION

When the PLASMACLUSTER button is pressed while

the unit is not operating, the PLASMACLUSTER

operation will be performed without accompanying

air conditioning mode (eg. HEATING or COOLING).

At this time, you may feel warm air coming out from

the unit air outlet if HEATING is performed with units

in other rooms. Indoor fan will decrease its rotating

speed and will turn ON and OFF depending on the

room temperature.

UNIT DOES NOT OPERATE IN YOUR REQUESTED

MODE

• When one indoor unit is operating in COOL or

DRY mode, you can not operate the other unit in

HEAT mode. (After a few seconds, a long BEEP

will be emitted, and the temperature indicator

on the indicator panel will indicate”

” and the

OPERATION lamp and TIMER lamp will blink

alternately.)

• When one indoor unit is operating in HEAT mode,

you can not operate the other unit in COOL nor

DRY mode. (After a few seconds, a long BEEP

will be emitted, and the temperature indicator

on the indicator panel will indicate”

” and the

OPERATION lamp and TIMER lamp will blink

alternately.)

UNIT DOES NOT SEND OUT AIR (PLASMACLUSTER

operation without accompanying air conditioning

mode, SELF CLEAN operation)

The other unit(s) is/are de-icing.

If the unit appears to be malfunctioning, check the

following points before calling for service.

IF THE UNIT FAILS TO OPERATE

Check to see if the circuit breaker has tripped or the

fuse has blown.

IF THE UNIT FAILS TO COOL (OR HEAT) THE

ROOM EFFECTIVELY

• Check the ﬁ lters. If dirty, clean them.

• Check the outdoor unit to make sure nothing is

blocking the air inlet or outlet.

• Check the thermostat is proper setting.

• Make sure windows and doors are closed tightly.

• A large number of people in the room can prevent

the unit from achieving the desired temperature.

• Check whether any heat-generating appliances are

operating in the room.

IF THE UNIT FAILS TO RECEIVE THE REMOTE

CONTROL SIGNAL

• Check whether the remote control batteries have

become old and weak.

• Try to send the signal again with the remote control

pointed properly towards the unit’s signal receiver

window.

• Check whether the remote control batteries are

installed with the polarities properly aligned.

Please call for service when TEMPERATURE

INDICATOR on the indicator panel blink.

Attention : votre produit

comporte ce symbole. Il signiﬁ e

que les produits électriques

et électroniques usagés ne

doivent pas être mélangés

avec les déchets ménagers

généraux. Un système de

collecte séparé est prévu pour

ces produits.

A. Informations sur la mise au rebut à l'intention des utilisateurs privés

(ménages)

1. Au sein de l'Union européenne

Attention : si vous souhaitez mettre cet appareil au rebut, ne le jetez pas dans

une poubelle ordinaire !

Les appareils électriques et électroniques usagés doivent être traités

séparément et conformément aux lois en vigueur en matière de traitement, de

récupération et de recyclage adéquats de ces appareils.

Suite à la mise en oeuvre de ces dispositions dans les Etats membres, les

ménages résidant au sein de l'Union européenne peuvent désormais ramener

gratuitement* leurs appareils électriques et électroniques usagés sur des sites

de collecte désignés.

Dans certains pays*, votre détaillant reprendra également gratuitement votre

ancien produit si vous achetez un produit neuf similaire.

*) Veuillez contacter votre administration locale pour plus de renseignements.

Si votre appareil électrique ou électronique usagé comporte des piles ou des

accumulateurs, veuillez les mettre séparément et préalablement au rebut

conformément à la législation locale en vigueur.

En veillant à la mise au rebut correcte de ce produit, vous contribuerez à

assurer le traitement, la récupération et le recyclage nécessaires de ces

déchets, et préviendrez ainsi les effets néfastes potentiels de leur mauvaise

gestion sur l'environnement et la santé humaine.

2. Pays hors de l'Union européenne

Si vous souhaitez mettre ce produit au rebut, veuillez contacter votre

administration locale qui vous renseignera sur la méthode d'élimination

correcte de cet appareil.

Suisse : les équipements électriques ou électroniques usagés peuvent être

ramenés gratuitement au détaillant, même si vous n'achetez pas un nouvel

appareil. Pour obtenir la liste des autres sites de collecte, veuillez vous

reporter à la page d'accueil du site www.swico.ch ou www.sens.ch.

B. Informations sur la mise au rebut à l'intention des entreprises

1. Au sein de l'Union européenne

Si ce produit est utilisé dans le cadre des activités de votre entreprise et que

vous souhaitiez le mettre au rebut :

Veuillez contacter votre revendeur SHARP qui vous informera des conditions

de reprise du produit. Les frais de reprise et de recyclage pourront vous être

facturés. Les produits de petite taille (et en petites quantités) pourront être

repris par vos organisations de collecte locales.

Espagne : veuillez contacter l'organisation de collecte existante ou votre

administration locale pour les modalités de reprise de vos produits usagés.

2. Pays hors de l'Union européenne

Si vous souhaitez mettre ce produit au rebut, veuillez contacter votre

administration locale qui vous renseignera sur la méthode d'élimination

correcte de cet appareil.

Les piles/accus fournies avec ce produit peuvent contenir des traces de Plomb.

Au sein de l’Union Européenne:

Le symbole de la poubelle sur roues barrée

laisse supposer que les piles/accus usagées ne doivent pas être mélangées

avec les déchets ménagers ! Il existe un mode de collecte séparé pour les

piles/accus usagées, ce qui permet d’effectuer un traitement et un recyclage en

accord avec la législation. Veuillez contacter une autorité locale pour plus de

renseignements sur le système mis en place.

Pour la Suisse: Les piles/accus usagées doivent être retournées chez votre

détaillant.

Pour les pays hors Union Européenne: Veuillez contacter une autorité locale

aﬁ n de connaître la bonne méthode à utiliser pour la collecte de vos piles/

accus usagées.

FR

P

b

Contient des gaz à effet de serre ﬂ uorés relevant du protocole de Kyoto

R410A (Potentiel de réchauffement planétaire 1980)

FR-1

FRANÇAIS

Lire attentivement ce manuel avant d’utiliser l’appareil.

Ce mode d’emploi doit être conservé en lieu sûr et rester

facile d’accès.

MISES EN GARDE POUR

L’INSTALLATION/LE DEMONTAGE/

LA REPARATION

• Ne pas essayer d’installer/démonter/réparer soi-

même l’appareil. Un fonctionnement inadéquat peut

provoquer des décharges électriques, des fuites d’

eau, des incendies etc. Consulter votre revendeur ou

un service de dépannage qualiﬁ é pour les opérations d’

installation/démontage/réparation de de l’appareil.

PRECAUTIONS D’EMPLOI

1

Ouvrir périodiquement une fenêtre ou une porte

pour aérer la pièce, en particulier lors de l’utilisa-

tion d’appareils à gaz. Une ventilation insufﬁ sante

risquerait de provoquer un manque d’oxygène.

2

Ne pas utiliser les touches avec les mains

mouillées. Cela risquerait de provoquer une élec-

trocution.

3

Par mesure de sécurité, couper le disjoncteur

lorsque l’appareil n’est pas utilisé pendant une

période prolongée.

4

Vériﬁ er périodiquement l’usure du rack de mon-

tage de l’unité extérieure aﬁ n de s’assurer qu’il

est ﬁ xé fermement en place.

5

Ne rien placer sur l’unité extérieure et ne pas mar-

cher dessus. L’objet ou la personne risquerait de

basculer ou de tomber, provoquant des blessures.

6

Cet appareil est conçu pour une utilisation privée.

Ne pas l’utiliser pour d’autres applications, com-

me par exemple dans un chenil ou une serre pour

l’élevage d’animaux ou la culture des plantes.

7

Ne pas placer une cuvette contenant de l’eau sur

l’appareil. Si l’eau pénètre dans l’appareil, l’iso-

lation électrique risquerait d’être détériorée et de

provoquer une électrocution.

8

Ne pas bloquer les entrées et sorties d’air de l’

appareil. Cela risquerait de provoquer un fonc-

tionnement insufﬁ sant ou des pannes.

9

S’assurer d’arrêter l’utilisation et de couper le

disjoncteur avant d’effectuer la maintenance ou le

nettoyage. Un ventilateur tourne à l’intérieur de l’

appareil et risquerait de vous blesser.

10

Cet appareil n’est pas destiné à être utilisé par

des enfants en bas âge ou des personnes han-

dicapées sans surveillance. Les jeunes enfants

doivent être surveillés aﬁ n de s’assurer qu’ils ne

jouent pas avec l’appareil.

PRECAUTIONS POUR

L’EMPLACEMENT/INSTALLATION

• S’assurer de connecter le climatiseur à une alimen-

tation de tension et de fréquence appropriées.

L’utilisation d’une alimentation ayant une tension et

une fréquence incorrectes peut endommager l’ap-

pareil et provoquer un incendie.

• Ne pas installer l’appareil dans un endroit où il

y aurait une fuite de gaz. Il risquerait de provoquer

un incendie.

Installer l’appareil dans un endroit peu poussiéreux,

sans fumées ni humidité dans l’air.

• Arranger le flexible de vidange pour assurer un

écoulement normal. Un écoulement insufﬁ sant ris-

querait de mouiller la pièce, les meubles etc.

• S’assurer qu’un disjoncteur de fuite ou un disjonc-

teur de circuit est installé, en fonction de l’emplace-

ment d’installation, pour éviter une électrocution.

CONSIGNES DE SECURITE IM-

PORTANTES

AVERTISSEMENTS CONCERNANT

L’UTILISATION

1

Ne pas tirer ou déformer le cordon d’alimentation.

Le fait de tirer sur le cordon d’alimentation ou une

mauvaise utilisation de ce dernier peut endom-

mager l’appareil et provoquer une électrocution.

2

Veiller à ne pas exposer votre corps directement

à l’air évacué pendant une longue période. Cela

risquerait d’affecter votre état physique.

3

Lors de l’utilisation du climatiseur pour des nour-

rissons, de jeunes enfants, des personnes âgées,

des personnes alitées ou handicapées, s’assurer

que la température de la pièce est appropriée aux

personnes qui se trouvent dans la pièce.

4

Ne jamais insérer d’objet dans l’appareil. Le fait

d’insérer des objets peut provoquer des blessu-

res à cause de la rotation à grande vitesse des

ventilateurs internes.

5

Mettre le climatiseur sans faille à la terre. Ne pas

connecter le ﬁ l de mise à la terre à un tuyau de gaz,

un tuyau d’eau, un paratonnerre ou un ﬁ l de mise

à la terre du téléphone. Une mise à la terre incom-

plète risquerait de provoquer un choc électrique.

6

Si l’on constate n’importe quelle anomalie dans

le climatiseur (ex : une odeur de brûlé), l’arrêter

immédiatement et couper le disjoncteur.

7

L’appareil doit être installé conformément aux

réglementations de câblage nationales.Une

connexion de câble incorrecte peut provoquer une

surchauffe du cordon d’alimentation, de la ﬁ che et

de la prise électrique et provoquer un incendie.

8

Si le cordon d’alimentation est endommagé, il

doit être remplacé par le fabricant ou son agent d’

entretien ou encore une personne possédant des

qualiﬁ cations similaires aﬁ n d’éviter tout danger.

Utiliser uniquement le cordon d’alimentation spé-

ciﬁ é par le fabricant pour le remplacement.

9

Ne pas éclabousser ou verser de l’eau directe-

ment sur l’appareil. L’eau risquerait de provoquer

une électrocution ou d’endommager l’appareil.

FRANÇAIS

• CONSIGNES DE SECURITE IMPORTANTES ............FR-1

• NOMENCLATURE ........................................................FR-2

• UTILISATION DE LA TELECOMMANDE ......................FR-4

• MISE EN PLACE DU FILTRE PURIFICATEUR D’AIR ..FR-5

• CONSEILS SUR LES ECONOMIES D’ENERGIE ........FR-5

• MODE AUXILIAIRE .......................................................FR-5

• FONCTIONNEMENT DE BASE ....................................FR-6

• REGLAGE DE LA DIRECTION DU DEBIT D’AIR .........FR-7

• DEBIT D’AIR PROGRESSIF .........................................FR-8

•

FONCTIONNEMENT A PLEIN REGIME

...................FR-8

• FONCTIONNEMENT DU PLASMACLUSTER ..............FR-9

• FONCTIONNEMENT DU NETTOYAGE

AUTOMATIQUE ............................................................FR-9

• ARRET APRES UNE HEURE .......................................FR-10

• FONCTIONNEMENT DE LA MINUTERIE ....................FR-10

•

CONSEILS A PROPOS DU PANNEAU D’INDICATEURS

..FR-12

• ENTRETIEN ..................................................................FR-12

• AUTRES REMARQUES SUR LE

FONCTIONNEMENT ....................................................FR-13

• AVANT D’APPELER LE SERVICE APRES-VENTE .....FR-14

TABLE DES MATIERES

FR-2

NOMENCLATURE

UNITE INTERIEURE

1 Touche AUX

2 Bouche d’entrée (Air)

3 Panneau d’ouverture

4 Filtre puriﬁ cateur d’air

5 Filtre à air

6 Fenêtre de réception

7 Volet d’aération à réglage vertical

8 Volet d’aération à réglage horizontal

9 Bouche de sortie (Air)

10 Télécommande

11 Voyant de PLASMACLUSTER (bleu)

12 Voyant de TEMPERATURE

13 Voyant de temp. EXTERIEURE (vert

)

14 Voyant de temp. de la PIECE (vert

)

15 Voyant de PLEIN REGIME (vert

)

16 Voyant de MINUTERIE (orange

)

17 Voyant de MARCHE (rouge

)

REMARQUE :

Les unités réelles peuvent varier légèrement de celles montrées ci-dessus.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

La pagina sta caricando ...

Sharp AY-XPC9JR Manuale del proprietario

Questo manuale è adatto anche per

Sharp AY-XPC9JR Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti