Brother PT-1750 Guida utente

User’s Guide

Guía de Usuario

Printed in China

LN9949001

175 0

• Read this User’s Guide before you start using your P-touch.

• Keep this User’s Guide in a handy place for future reference.

• Antes de usar su equipo por primera vez, lea cuidadosamente esta Guía de Usuario.

• Guarde esta Guía de Usuario para futuras referencias.

P-touch 1750 cover 1-4

P-touch 1750 cover 2-3

INTRODUCTION

Thank you for purchasing the P-touch 1750!

Your new P-touch will allow you to create labels for any need. Its versatility enables you to

design custom labels by choosing from a variety of frame designs and from many characters

sizes and styles. In addition, the four tape widths (1/4” (6 mm), 3/8” (9 mm), 1/2” (12 mm),

and 3/4” (18 mm)) and variety of tape colors allow you to print personalized labels, useful

for color-coded filing.

You no longer have to worry about urgent tasks that require professional printing. In the

office, the factory, the lab and the home, the quality and performance of the P-touch 1750

makes it an extremely versatile and practical machine.

Finally, as you may want to refer to this User’s Guide occasionally, we suggest you keep this

manual in a convenient place, as you may wish to refer to it occasionally.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

-Reorient or relocate the receiving antenna

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/television technician for help.

-Changes or modiﬁcations not expressly approved by Brother Industries, Ltd. could

void the user’s authority to operate the equipment.

1

CONTENTS

Getting Started

GENERAL DESCRIPTION ................................................................................... 2

GENERAL PRECAUTIONS .................................................................................. 3

BATTERIES ......................................................................................................... 4

AC ADAPTER ..................................................................................................... 5

TAPE CASSETTE ................................................................................................. 5

ATTACHING LABELS ......................................................................................... 6

PRINT HEAD & ROLLERS ................................................................................... 8

For Your Information

POWER KEY ....................................................................................................... 9

CURSOR KEYS ................................................................................................... 9

CODE & SHIFT KEYS ........................................................................................ 10

SPACE KEY ....................................................................................................... 11

RETURN KEY .................................................................................................... 12

BS KEY ............................................................................................................. 13

CLEAR FUNCTION .......................................................................................... 13

ACCENT FUNCTION ....................................................................................... 14

SYMBOL FUNCTION ....................................................................................... 15

SIZE FUNCTION .............................................................................................. 17

STYLE FUNCTION ........................................................................................... 18

UNDERLINE FUNCTION ................................................................................. 19

FRAME FUNCTION .......................................................................................... 20

BIG SIZE FUNCTION ....................................................................................... 21

TAPE MARGIN FUNCTION ............................................................................. 23

MIRROR PRINTING FUNCTION ...................................................................... 24

PRINT KEY & FEED FUNCTION ....................................................................... 25

NUMBERING FUNCTION ............................................................................... 25

REPEAT PRINTING FUNCTION ....................................................................... 27

MEMORY FUNCTIONS .................................................................................... 28

TROUBLESHOOTING ...................................................................................... 31

ERROR MESSAGE LIST ..................................................................................... 32

SPECIFICATIONS ............................................................................................. 34

PT-1750 CONTACT INFORMATION (For USA Only) ...................................... 35

2

TOP VIEW

BOTTOM VIEW

Getting Started

GENERAL DESCRIPTION

Tape compartment

cover

LCD display

Keyboard

Tape cutter lever

AC adapter

connector

Tape exit slot

Battery compartment cover

3

KEYBOARD & LCD DISPLAY

• Use only Brother TZ tapes with this machine. Do not use tapes that do not have the

mark.

• Do not pull on the tape being fed from the P-touch. This may damage the tape cassette.

• Do not use the machine in dusty places, and keep it out of both direct sunlight and rain.

• Do not expose the machine to high temperatures or high humidity. Never leave it on the

dashboard or in the back of your car.

• Do not leave any rubber or vinyl on the machine for an extended period of time. Doing

so may cause staining.

• Do not clean the machine with alcohol or other organic solvents. Use a soft, dry cloth

only.

• Do not put any foreign objects into or anything on the machine.

• To avoid injuries, do not touch the cutter’s edge.

• Use only the AC adapter (model AD-24) designed exclusively for this machine. Use of

any other adapter will void the warranty.

S

Power key

Return key

Cursor keys

Delete key

GENERAL PRECAUTIONS

4

• Do not try to disassemble the AC adapter.

• When the machine is not being used for a long period of time and it is not necessary to

keep the text ﬁles stored in the memory, disconnect the AC adapter, and remove the bat-

teries to prevent them from leaking and damaging the machine.

• When the AC adapter is connected, unplugging the adapter from the electrical outlet

before unplugging it from the machine can delete all text ﬁles in the memory, even if bat-

teries are installed.

• Use six AA batteries in this machine.

• To prevent damage during shipment, a clear protective sheet is placed over the LCD

panel. Remove this clear protective sheet before beginning use.

This lightweight and portable machine can be used anywhere by installing six (6)

AA batter-

ies

. When you change the batteries, always replace all six at the same time.

To change the batteries:

1

Remove the battery compartment cover on

the back of the machine.

2

If batteries are already installed, remove

them.

3

Insert six new AA batteries, making sure

that they face the correct direction.

4

Attach the battery compartment cover.

☞

Be sure to insert the new batteries

within ﬁve minutes of removing the old ones, otherwise the text shown in the

display and any text ﬁles stored in the memory will be lost (unless the machine

is plugged into an AC outlet with the AC adapter).

BATTERIES

5

The AC adapter (model AD-24) allows you to use this machine wherever there is an electri-

cal outlet.

To connect the AC adapter:

1

Insert the plug on the adapter cord into the

connector marked DC IN 7-9V on the right

side of the machine.

2

Insert the plug on the adapter into the near-

est standard electrical outlet.

☞

Only use the AC adapter designed

exclusively for this machine.

Remove the batteries and disconnect

the AC adapter if you do not intend

to use this machine for an extended

period of time. When the power is

disconnected, all text shown in the

display and stored in the memory will be lost.

It is recommended that you use the AC adapter when printing large fonts on

3/4

″

(18-mm)-wide tape since this operation can quickly drain the batteries.

A single TZ tape cassette is supplied with this unit. However, since TZ tape cassettes are

available for this machine in a wide variety of colors and sizes, it is possible to make distinc-

tive color-coded and stylized labels.

In addition, this machine has been designed to allow you to change the tape cassettes

quickly and easily.

To change the tape cassette:

1

Lift open the tape compartment cover. The installed cassette is also released.

2

If a tape cassette is already installed, remove it by pulling it straight up.

3

If the ink ribbon in the other tape cassette is loose, use your finger to wind the toothed

wheel in the direction of the arrow on the cassette until there is no slack in the ribbon.

Also, make sure that the end of the tape feeds under the tape guides.

☞

If you are using a new tape cassette provided with a stopper, be sure to remove

the stopper.

AC ADAPTER

TAPE CASSETTE

6

4

Insert the tape cassette firmly into the tape

compartment, making sure that the entire

back of the cassette touches the bottom of the

compartment.

☞

When inserting the tape cassette, make

sure that the inner ribbon does not

catch on the corner of the metal guide.

5

Close the compartment cover, then turn on

the machine if it is off.

6

Hold down

f

and press

g

once to

advance the tape and remove any slack.

7

Push down on the tape cutter lever to cut off

any excess tape.

STICK

A stick is enclosed in the right side of the tape compartment cover of the P-touch. Use this

stick when pasting laminated tape to an object.

1

Open the tape compartment cover.

2

Pull the tip of the stick towards you with your finger.

3

Hold the tip of the stick and pull up to remove it.

ATTACHING LABELS

7

LAMINATED TAPE

The enclosed stick enables you to easily remove the backing from labels printed on lami-

nated tapes.

1

Hold the tape in your left hand, with the printed surface facing up, and hold the stick in

your right hand.

2 Pass the tape halfway through the long narrow hole in the stick.

3 Turn the stick three-quarters of a turn towards you and pull the stick away from you as

shown below.

4 Peel off the label backing.

FABRIC TAPE

Fabric tape is used to attach a piece of fabric printed with your text onto garments using an

iron. After printing the text onto fabric tape and cutting off the label using scissors, place the

label on an ironed garment at the location where you wish to attach it in such a way that the

printed text can be read correctly. Cover the label with another piece of cloth and use an

iron set to a medium-high temperature (320 to 356 ˚F (160 to 180 ˚C)) to press down firmly

for 10 to 15 seconds. For more details, refer to the instructions included with the fabric tape

cassette.

GH

ABCDEF

8

Occasionally, specks of dust or dirt become attached to the machine’s print head and rollers.

This is particularly likely when you are using the unit outdoors or in a very dusty environ-

ment. If a section of the print head is covered with dust, a blank horizontal streak may

appear through the label text. Therefore, as with a tape recorder, the machine’s head may

need to be cleaned from time to time.

To clean the print head and rollers:

1

Turn off the machine.

2 Open the tape compartment cover, then remove the tape cassette if one is installed.

The print head and rollers are located in the tape compartment.

3 Print head: Use a dry cotton swab to gently wipe the print head with an up-and-down

motion.

Rollers: Use a dry cotton swab to wipe each roller with an up-and-down motion while

rotating them with your finger.

4 Install a tape cassette, close the tape compartment cover, and then try printing again.

5 If dust still remains, repeat steps 3 and 4 using a cotton swab dipped in isopropyl

(rubbing) alcohol.

If none of the above works, contact your service representative.

☞ Cleaning can also be done by using the optional print head cleaning cassette (TZ-

CL4).

PRINT HEAD & ROLLERS

Print head

Rollers

Cotton swab

9

The power key ( b ) is located in the top right-hand corner of the keyboard. If batteries

have been installed or the machine has been plugged in using the AC adapter, the previous

session’s information is displayed when the machine is turned on. This feature allows you to

stop work on a label, turn off the machine, and return to it later without having to re-enter

the text.

☞ If you press any key during the opening message, you can skip the message.

The machine will automatically turn off if no key is pressed within 5 minutes. The machine’s

internal memory stores the current session’s information and displays it when you turn on

the machine again.

To turn on the machine:

● Press b. The previous session’s information appears in the LCD display.

To turn off the machine:

● Press b. The current session’s information is stored in the internal memory.

The machine’s LCD display shows one row of 15 characters; however, the text that you cre-

ate can be up to 60 characters long. You can review and edit your text by using the cursor

keys to move the cursor so that different parts are shown in the display.

LEFT CURSOR KEY

To move the cursor one character to the left:

● Press < once.

To move the cursor several characters to the left:

● Hold down < until the cursor moves to the desired position.

To move the cursor to the beginning of the text line:

● Hold down f and press <.

For Your Information

POWER KEY

CURSOR KEYS

10

RIGHT CURSOR KEY

To move the cursor one character to the right:

● Press > once.

To move the cursor several characters to the right:

● Hold down > until the cursor moves to the desired position.

To move the cursor to the end of the text line:

● Hold down f and press >.

Most characters can be entered simply by pressing their keys. However, to use special func-

tions or to enter capital letters, accented characters and some symbols, the following special

keys are necessary.

CODE KEY

To use a function printed above a key:

● Hold down f and press the key immediately below the desired function.

EXAMPLE

SHIFT KEY

To type in a capital letter or a symbol printed in the top left-hand corner of a key:

● Hold down e and press the key of the desired letter or symbol.

To start the Feed function:

● Hold down f and press g once.

CODE & SHIFT KEYS

FEED

11

EXAMPLE

The Caps mode is similar to holding down e. It allows you to type capital letters continu-

ously.

To type in many capital letters:

1 Hold down f and press e. The Caps indicator on the left side of the display lights

up.

2 Press the keys of the desired letters or symbols.

3 To exit Caps mode, hold down f and press e. The Caps indicator goes off.

The Space key ( g ) lets you add blank spaces between characters in your text. It is differ-

ent from the right cursor key ( > ), which just moves the cursor without adding blank

spaces.

To add a space:

● Press g.

To type in “%”:

● Hold down e and press 5.

5

5%

SPACE KEY

12

EXAMPLE

Like on a typewriter or word processor, this machine’s return key ( h ) is used to end a

line of text and start another one. When you have finished entering one line, press the return

key to make a new line and move the cursor to it.

☞ A label can only contain a maximum of two text lines. If you press h when the cur-

sor is located in the second line, the error message “2 LINE LIMIT!” will appear.

The return key can also be used to select an item from a list (e.g., add a symbol or accented

character to the text) or to apply a selected setting.

Some questions asking you to confirm a command may appear on the LCD display, espe-

cially when the function that you have chosen will delete or affect files. In these cases, press-

ing h is like answering “yes”.

☞ To answer “no”, press c. Refer to “BS KEY” on page 13.

To add a new line:

● Press h. The return mark ( ) appears to indicate the end of the line.

To add a space:

● Press g.

Maximum number of lines

that can be printed

Tape widths

1 1/4” (6 mm)

2 3/8” (9 mm), 1/2” (12 mm), 3/4” (18 mm)

J.

RETURN KEY

13

To select an item from a list:

● Press h.

To answer “yes”:

● Press h.

The delete key ( c ) allows you to remove characters to the left of the cursor’s current posi-

tion. It differs from the left cursor key ( < ), which only moves the cursor without deleting

any characters.

The delete key can also be used to quit most functions and return to the previous display

without changing the text.

Some questions asking you to confirm a command may appear on the LCD display, espe-

cially when the function that you have chosen will delete or affect files. In these cases, press-

ing c is like answering “no”.

☞ To answer “yes”, press h. Refer to “RETURN KEY” on page 12.

To delete one character:

1 Press < or > to position the cursor below the character immediately to the right of

the character that you wish to delete.

2 Press c once.

To quit a function without changing your text:

● Press c to return to your text.

To answer “no”:

● Press c.

When clearing the display before entering new text, the Clear function can be used to

choose whether all of the text is erased.

☞ The Clear function only deletes the text. The format functions (Size, Style, Underline,

Frame, Big size, Tape margin, and Mirror printing) do not return to the default set-

tings, but stay as they are.

To delete all of the text:

1 Hold down f and press c.

2 All of the text will be deleted.

BS KEY

CLEAR FUNCTION

14

EXAMPLE

The Accent function can also be used to add accented characters to your text.

The accented characters are grouped according to the capital or small letter that they are

combined with. The following accented characters are available:

To clear the text:

1 Hold down f and press c.

Letters Accented characters Letters Accented characters

a à á ä â ã æ I Í Ï Î

A À Á Ä Â Ã Æ n ñ

cçNÑ

C Ç o ó ö ô õ

e è é ë ê e˜ O Ó Ö Ô Õ

E È É Ë Ê E u ù ú ü û

i í ï î U Ù Ú Ü Û

Reynolds Tel:(5

ACCENT FUNCTION

˜

15

To type in an accented character:

1 Hold down f and press d. The message “A – U?” appears on the display.

2 Press the key of the letter in the desired accented character.

☞ To type a capital letter, hold down e (or hold down f and press e to turn

on Caps mode) before pressing the letter key.

3 Press < or > until the cursor is under desired accented character.

4 Press h. The accented letter is added to the text.

EXAMPLE

In addition to the letters, symbols and numerals on the key tops, there are 48 additional

marks available with the Symbol function.

To add the accented character “É”:

1 Hold down f and press d.

2 Hold down e and press E.

3 Press > until the cursor is under É.

4 Press h.

A-U?

ÈÉËÊE

RESUMÉ

SYMBOL FUNCTION

16

The following symbols are available:

To type in a symbol:

1 Press d. The message “1-4?” appears on the display.

2 Press a key 1 to 4 to choose the set that contains the desired symbol.

3 Press < or > until the cursor is under the desired symbol.

4 Press h. The symbol appears in the text.

EXAMPLE

Group Symbol

2§

23

234

3

4

To add the symbol “ ”:

1 Press d.

2 Press 3.

3 Press > until the cursor is under .

4 Press h.

TM

☞

♥

★

1-4?

DANGER

17

The character size can be adjusted using the Size function. The following table shows the

character sizes.

The default size setting is AUTO. The currently selected size setting is always shown by the

indicator above the display.

When 6 mm tape is installed and SIZE 3, 4 and 5 is set for horizontal printing or SIZE 2, 4

and 5 is set for vertical printing, the “CHR_SIZE:AUTO?” message will display. Press h to

print in the AUTO size.

To change the size setting:

1 While holding down f, press 1 once, and keep f held down to display the

current size setting.

2 While still holding down f, continue pressing 1 until the desired size setting is

displayed and is shown by the size indicator.

☞ The current character size setting is also shown by the size indicator above the

display.

3 Release f to apply the selected size setting to the entire text.

Size Character

SIZE 1 Standard Size

SIZE 2 Double Width

SIZE 3 Double Height

SIZE 4 Double Width & Double Height

SIZE 5 4 × Width & Double Height

AUTO

1/4” (6 mm) tape: SIZE 1

3/8” to 3/4” (9 mm to 18 mm) tape: SIZE 4

SIZE 1 SIZE 2 SIZE 3 SIZE 4 SIZE 5

Sample

SIZE FUNCTION

18

EXAMPLE

You can choose from nine different character styles to apply to your text.

☞ Characters printed using the smaller sizes may be difﬁcult to read if certain style set-

tings (e.g., ITALIC+SHADOW) are selected.

The following style settings are available:

NORMAL, OUTLINE, BOLD, SHADOW, ITALIC,

ITALIC+OUTLINE, ITALIC+BOLD, ITALIC+SHADOW, VERTICAL

The default style setting is NORMAL. The style indicator at the bottom left of the display

shows the current style setting when any setting other than NORMAL is selected.

Refer to Reference at the end of this section for samples of the available settings.

To change the style setting:

1 While holding down f, press 2 once, and keep f held down to display the

current style setting.

2 While still holding down f, continue pressing 2 until the desired style setting is

displayed.

3 Release f to apply the selected style setting to the entire text.

☞ If there are two lines of text, they are printed in the NORMAL style, regardless of

the selected style setting.

To select SIZE3:

1 While holding down f, press 1

once, and keep f held down.

2 While still holding down f, continue

pressing 1 until SIZE3 is displayed.

3 Release f.

AUTO

SIZE3

STYLE FUNCTION

La pagina sta caricando ...

Brother PT-1750 Guida utente

Brother PT-1750 Guida utente

in altre lingue

Documenti correlati

Altri documenti