ORIENT RA-AC0J09L Manuale utente

1

ENGLISH

MECHANICAL WATCHES

INSTRUCTION MANUAL

Thank you for choosing our product. To ensure prolonged use and optimum

performance, please read this instruction manual carefully and familiarize

your-self with the terms of the guarantee.

Please keep this Instruction Manual handy for future reference.



SAFETY PRECAUTIONS

Make absolutely sure to observe the demarcated contents indicated below to

prevent any possible physical danger and property damage to you as well as

other people concerned.

... A demarcation with this symbol represents the contents

assuming possibility for death or serious injury

when the product is used in any manner different from

given instructions.

... A demarcation with this symbol represents the contents

assuming possibility of causing human injury or

material damage only when a product is used in any

manner different from given instructions.

WARNING

!

CAUTION

!

2

ENGLISH



IN HANDLING THE WATCH

(1) Water-resistance

Conditions

of use

Type

Underwater

operation of

crown and

operation

of crown

with drops

of water

on it

Exposure

to small

amounts

of water

(face-wash-

ing, rain,

etc.)

Water sports

(swimming,

etc.),

frequent

contact with

water (car-

washing,

etc.)

Skin diving

(air tanks

are not

used)

Scuba

diving

(air tanks

are used)

Mixed-gas

Diving

(using

helium

gas)

Non water resistant

Without

WATER

RESISTANT

(WATER

RESIST)

× × × × × ×

Water

resistant

watches

Water

resistant for

daily life

WATER

RESISTANT

(WATER

RESIST)

×



× × × ×

Reinforced

water

resistance

for daily

life I

WATER

RESISTANT

(WATER

RESIST)

5bar (50m)

×

 

× × ×

Reinforced

water

resistance

for daily

life II

WATER

RESISTANT

(WATER

RESIST)

10bar (100m)

20bar (200m)

×

  

× ×

Diver’s

watches

Diver’s

watch for Air

Diving

AIR DIVER’S

100m / 150m

200m

×

   

×

Diver’s

watch for

Mixed-gas

Diving

He-GAS

DIVER’S

200m / 300m /...

×

    

* It is recommended that you use the watch correctly following the above-mentioned scope of usage

after ascertaining water resistance precautions marked on the dial or caseback.

3

ENGLISH

WARNING

!

1

A watch with water resistance for daily life 3 bar (30m) can be used

during face-washing, etc. but cannot be used in an environment in which

it will be submerged in water.

2

A watch with reinforced water resistance for daily life I 5 bar (50m) can be

used while swimming, etc. but cannot be used during any type of diving

including skin diving.

3

A watch with reinforced water resistance for daily life II 10 or 20 bar (100m

or 200m) can be used while skin diving, but cannot be used while scuba

diving using oxygen tanks or saturation diving using helium gas, etc.

CAUTION

!

4

Keep the crown pushed in at all times (in the normal position) while using

the watch. If the crown is the screwed-down type, check that it is securely

screwed down.

5

Do not operate the crown underwater, or while the watch is wet. Water

may enter the interior of the watch and defeat the water resistance.

6

If your watch is non-water resistant, beware of splashes of water (during

face washing, rain, etc.) and sweat. If the watch becomes wet from water

or sweat, wipe the moisture off with a dry, soft cloth.

7

Even with a water resistant watch for everyday use, avoid directing strong

jets of mains water onto the watch. Water pressure above the limit can

apply, which may defeat the water resistance.

8

With a water resistant watch for everyday use, rinse sea water off the

case after exposure, then wipe it thoroughly to avoid corrosion and other

effects.

9

The interior of the watch contains some amount of moisture, which may

cause fogging on the inside of the glass when the outside air is cooler

than the internal temperature of the watch. If the fogging is temporary

it causes no harm inside the watch, but if prolonged, or if water enters

the watch, consult your place of purchase and do not leave the problem

untreated.

WARNING

!

4

ENGLISH

(2) Shock

1

Be sure not to carry the watch when you engage in

strenuous sports, whereas playing such light sports as golf,

etc., will not adversely influence the watch.

2

Avoid a violent shock such as dropping the watch on the

floor.

(3) Magnetism

1

If the watch is left at a location with strong magnetism for an extended

period of time, the components may be magnetized, resulting in

malfunction. Be careful.

2

The watch may temporarily speed up or slow down when exposed to

magnetism. Precision is restored when placed away from magnetism. In

such a case, reset the time.

(4) Vibration

The watch may lose precision if subjected to strong

vibrations such as from riding motorcycles, using

jackhammers, chain saws, etc.

(5) Temperature

In environments below and above normal temperatures (5°C-35°C), the

watch may malfunction and stop.

CAUTION

!

Do not use the watch at high temperatures, such as in a sauna. The

watch may heat and cause burns.

(6) Chemicals, Gases, etc.

Utmost caution must be exercised when coming into contact with gases,

mercury, chemicals (paint thinner, gasoline, various solvents, detergents

containing such components, adhesives, paint, drugs, perfumes,

cosmetics, etc.), and so forth. Such may cause discoloration of the

watchcase, watchband, and dial face. Discoloration, deformation, and

damage to various resin-based component parts may also occur.

5

ENGLISH

(7) About accessory parts

CAUTION

!

Do not attempt to disassemble or modify the watch.

WARNING

!

Store the bracelet/strap pin and other small parts out of the reach of

children.

If any small parts are swallowed, immediately contact a doctor.

(8) Allergic reactions

CAUTION

!

If you develop a skin rash or your skin becomes abnormally irritated due

to contact with the watch or strap, stop wearing the watch immediately

and consult a doctor.

(9) About “luminous light”

This watch has luminous light on the hands and dial.

The luminous light is a safe paint that stores sunlight and artificial light

without using any radioactive material, and emits that light in a dark

setting. As the paint discharges the stored light, it will become dimmer

over time. The amount of light emitted and the time that light is emitted

depends on various factors when the light is stored, such as the shape

of the glass, the thickness of the paint, surrounding brightness level, the

distance from the watch to the light source, and the light absorption level.

Please note that when not enough light energy is stored, the watch may

emit weak light or emit light for only a short time.

(10) Water resistant watchband

Some products employ leather and nylon bands on which a special

treatment to resist perspiration and water absorption have been applied.

Please understand that the water resisting effect of this watchband can

be lost depending on the period and conditions of use.

6

ENGLISH

 HOW TO IDENTIFY THE CALIBER NUMBER

Check the caliber number by referring to the model number of your watch or

the case code on the watch’s case back.

1. Searching by the model number

Check the model number on the guarantee supplied with your watch. You

can also see the number on the product tag put on the watch.

When the model number is 13 digits:

The 4th and 5th digits is the caliber number.

(Ex.) R¨- XXXXXXXXXX

When the model number is 10 digits :

The 1st and 2nd digits is the caliber number.

(Ex.) XXXXXXXXXX

2. Searching by the case code

Check the case code on the case back of your watch.

(A) Watch with EPSON engraving

Case code

(B) Watch with ORIENT engraving

(A) It has displayed as XXXX-XXXX.

The first three digits indicate the caliber number.

(In the example, F6D is Cal.)

(B) It has displayed as XXXX-XX.

The first two digits indicate the caliber number.

(In the example, AA is Cal.)

* The place of case code may vary and its letter size may be small and

difficult to see depending on the characteristics of watches.

* The pictures and illustrations on this manual may differ from the actual

appearance of your watch but the function and operation procedures are

the same.

7

ENGLISH



SPECIFICATIONS

Caliber

Number of

jewels

Date Day of week

Second hand halt

mechanism

Remark1*

AA F69 22

○ ○ ○

8:00P.M.-4:00A.M.

AC F67 22

○

–

○

8:00P.M.-2:00A.M.

AG F6T 22

– –

○

8:00P.M.-4:00A.M.

AP F62 24

○

–

○

8:00P.M.-1:00A.M.

(1) Vibrations: 21,600 vibrations/1 hour

(2) Daily accuracy: +25 sec. to -15 sec.

(3) Drive system: Mainspring winding (Hand-winding)

(4) Running time: More than 40 hours

(5) Shock-proof bearings to protect the balance with hairspring from shocks.

The stated daily accuracy is in the following conditions:

• After 24 hours at room temperature with the mainspring wound fully and

the dial facing up.

• Due to the characteristics of the automatic winding watch, the time may

deviate from the stated “daily accuracy” depending on the following

conditions: amount of time the watch is worn each day, position of the

watch, movement of your arm, winding condition of the mainspring.

• Determine the deviation from not just a day but a period of about a week.

Product specifications may change without notice, for improvement.

CAUTION

!

* Avoid setting the date during the time periods listed in “Remark1” above

since the calendar changes during this time. If the date is set during this

time period, the date may not change or the watch may malfunction. Be

sure to move the hour and minute hands away from this time period when

setting the date.

8

ENGLISH



NAMES AND FUNCTIONS OF INDIVIDUAL COMPONENT PARTS

A: Hour hand

E:

Date 1. Normal position

B: Minute hand F: Crown 2. First click: Calendar setting

C: Second hand G: Dial 3. Second click: Time setting

D:

Day of the week

<AA(F69)> <AC(F67)>

<AG(F6T)> AP(F62)

* The position of the crown, date indicator, or day of the week window may

be different, depending on the model.

* Some models have the rotating bezel and the internal rotating ring. Please

check this instruction manual for how to use it.

MON

G

A

B

D

C

E

F

1

2

3

G

A

B

C

E

F

12

3

G

B

F

1 2

3

A

C

12

3

A

B

C

E

G

F

9

ENGLISH



AUTOMATIC WINDING MECHANISM

(1) The mainspring is wound by natural movements of your

arm when wearing the watch on your wrist.

(2) If your watch stops, swing the watch back and forth ten

or more times to re-start the second hand. After it starts

moving, set the date and time.

(3) This watch will run approximately 40 hours after it is fully

wound. If it is not wound enough, the watch may lose

accuracy. In order to maintain the watch’s accuracy, we recommend

wearing the watch at least 8 hours a day.



HAND WINDING MECHANISM

(1) The mainspring is wound up manually.

(2) To wind the spring, ensure that the crown is in its normal position and

slowly turn it clockwise.

Turning the crown counterclockwise will have no effect.

(3) When the watch is in the stopped state, the spring can be wound

sufficiently by rotating the crown approximately 30 times. Since the crown

will rotate even when winding is complete, wind the watch using the

above number of turns as a guide.

(4) This watch will run approximately 40 hours after the spring is fully wound.



MODELS WITH SCREWED-DOWN CROWN

Depending on the model, you may not be able to pull the crown out without

unscrewing it (models with screwed-down crown).

Operate this type of watch as follows:

(1) Before setting the date and time, first turn the crown counterclockwise to

loosen the screw lock.

(2) After setting the date and time, turn the crown clockwise while pressing

in, until it stops turning to securely tighten the screw.

10

ENGLISH



HOW TO SET THE TIME & CALENDAR [AA(F69)]

(1) Pull out the crown to the second click

when the second hand reaches the 12

o’clock position.

(The second hand stops.)

(2) Turn the crown counterclockwise and

set the current time.

* When setting the time, first bring the

hand back slightly earlier than the

actual time and then move it forward

to the actual time.

* For the watch with a calendar, make

sure that you set either a.m. or p.m.

without fail. The date changes at

[twelve o’clock midnight].

(3) Pull the crown out to the first click.

* The crown on this watch can be

pulled out to either of two clicks.

Turn

counterclockwise

SAT

11

ENGLISH

(4) Turn the crown counterclockwise, and

set the date to that for the current day.

(5) Turn the crown clockwise to set the

day of the week to the current day.

* This watch has a bilingual day of the

week function.

Turn the crown to select the desired

language.

The display languages differ

depending on the model.

** Correcting the date at the end of the month

The date will have to be corrected for months that have 30 days, or those

that have less than 30 days. After the date switches over to the first day of

the succeeding month, set the date to the [First (1)].

(6) Push the crown back to the normal

position.

Turn

counterclockwise

SAT

Turn clockwise

MON

12

ENGLISH



HOW TO SET THE TIME & CALENDAR [AC(F67)]

(1) Pull out the crown to the second click

when the second hand reaches the 12

o’clock position.

(The second hand stops.)

(2) Turn the crown counterclockwise and

set the current time.

* When setting the time, first bring the

hand back slightly earlier than the

actual time and then move it forward

to the actual time.

* For the watch with a calendar, make

sure that you set either a.m. or p.m.

without fail. The date changes at

[twelve o’clock midnight].

(3) Pull the crown out to the first click.

* The crown on this watch can be

pulled out to either of two clicks.

Turn

counterclockwise

13

ENGLISH

(4) Turn the crown counterclockwise, and

set the date to that for the current

day.

** Correcting the date at the end of the

month

The date will have to be corrected for

months that have 30 days, or those that

have less than 30 days. After the date

switches over to the first day of the

succeeding month, set the date to the

[First (1)].

(5) Push the crown back to the normal

position.

◆

HOW TO SET THE TIME [AG(F6T)]

(1) Pull out the crown to the second click

when the second hand reaches the 12

o’clock position.

(The second hand stops.)

(2) Turn the crown counterclockwise and

set the current time.

Turn

counterclockwise

Turn

counterclockwise

14

ENGLISH

(3) Press the crown in to the normal

position.



HOW TO SET THE TIME & CALENDAR [AP(F62)]

(1) Pull out the crown to the second click

when the second hand reaches the 12

o’clock position.

(The second hand stops.)

(2) Turn the crown counterclockwise and

set the current time.

* When setting the time, first bring the

hand back slightly earlier than the

actual time and then move it forward

to the actual time.

* For the watch with a calendar, make

sure that you set either a.m. or p.m.

without fail. The date changes at

[twelve o’clock midnight].

Turn

counterclockwise

15

ENGLISH

(3) Pull the crown out to the first click.

* The crown on this watch can be

pulled out to either of two clicks.

(4) Turn the crown clockwise, and set the

date to that for the current day.

** Correcting the date at the end of the

month

The date will have to be corrected for

months that have 30 days, or those that

have less than 30 days. After the date

switches over to the first day of the

succeeding month, set the date to the

[First (1)].

(5) Push the crown back to the normal

position.

06

45

03

15

Turn clockwise

16

ENGLISH

◆

HOW TO SET THE MONTHLY CALENDAR

Some models come with a monthly calendar.

The monthly calendar can be used by turning the crown at the 4 o’clock

position to set the rotating ring inside the watchcase and aligning it with the

day of the week that is printed on the dial.

Turn the crown to align the first day of the month to the appropriate day of

the week.

* Note that when setting the first day of the month, if the days at the end of

the month (31st, etc.) are aligned with the section that does not have the

days of the week printed on the dial (3 - 4 o’clock side), days of the week

will not be indicated at the end of the month.

17

ENGLISH



HOW TO MEASURE THE ELAPSED TIME

Some the model, using a rotating bezel and internal rotating indicator ring,

you can know the elapsed time.

The rotating bezel or internal rotating indicator ring is engraved in 60

minutes.

Set the



mark to the minute hand by turning a ring. After a certain period

of time, measure the elapsed time by the number on the rotating bezel or

internal rotating indicator ring pointed to by the minute hand.

You can also set the



mark as a desired time to remind you how long time

is still remain for an appointment.

Rotating bezel

E

l

a

p

s

e

d

T

i

m

e

20 minutes have passed

since 10:10

E

l

a

p

s

e

d

T

i

m

e

Internal rotating indicator ring

Crown for

internal rotating

indicator ring

10 minutes have passed

since 10:08

* The design of the



mark may differ depending on the model.

* Some models have a reverse rotation prevention mechanism on the

rotating bezel.

* How to turn the internal rotating indicator ring differs depending on the

model.

18

ENGLISH



HOW TO USE SIMPLE THE WORLD TIME

Using the rotating bezel or the internal rotating indicator ring, you can easily

know the time in each city by the dial or the display on the exterior.

In the figure, the internal rotating indicator ring displays the time divided

into 24 parts.

* The expression method of world time differs depending on the model.

In order to set and display the world time, there are those that display the

time and city interchanged, and those that use a rotating bezel.

Turn the crown for the internal rotating indicator ring, set the current time to

the city displayed on the dial.

If the time in Tokyo is 10:08 (example), set 10 on the internal rotating

indicator ring to TOKYO on the dial. At this time, the time in each the city will

be the time corresponding to the number on the internal rotating indicator

ring.

Internal rotating indicator ring

Crown for the internal

rotating indicator ring

Match “10” to “TOKYO”

19

ENGLISH

Turn the interior rotating ring to set the current time to the area of the world

map drawn on the dial. In the figure on the below, the time in Japan is 10:08,

so set the rotation indicator ring “10” to Japan on the world map drawn on

the dial. For times in other cities, look at the numbers on the corresponding

indicator ring. For example, around London is about 1 a.m..

Internal rotating indicator ring

Japan is drawn around here.

Current time around London : 1 a.m.

Crown for the internal rotating

indicator ring

* For the rotating bezel, rotate the bezel directly.

* How to turn the internal rotating indicator ring differs depending on the

model.

20

ENGLISH



HOW TO USE THE SIMPLE COMPASS

You can know the approximate direction by using the rotating bezel or the

internal rotating ring and the hour hand.

In the figure, the internal rotating ring is marked with the mark of a direction.

When using the simple compass, be sure to set it to the time of your current

location. At lower latitudes, this function may not be useful, depending on

the season.

1 Put the watch on the level

place. Point the hour hand

in the direction of the sun.

2 The middle of the position

of the hour hand and the

position of “12:00” position

is “south”.

In case 9 o’clock (Figure 1),

set the “S” on the directional

scale to the 10:30 position

on the dial.

3 A direction (7:30) that “E” of

the direction scale shows is

“the East”.

12:00

South

Sun

East

Rotation ring with direction scale

Crown for internal rotating indicator ring

(Figure 1)

La pagina sta caricando ...

ORIENT RA-AC0J09L Manuale utente

ORIENT RA-AC0J09L Manuale utente

in altre lingue

Documenti correlati

Altri documenti