ProLights PIXIEZOOM Manuale utente

Marca: ProLights

Modello: PIXIEZOOM

Categoria: Stroboscopi

Tipo: Manuale utente

PIXIEZOOM

PARLED ZOOM

EN - IT

USER MANUAL

MANUALE UTENTE

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.003-12/18

PIXIEZOOM

Packing content

• PIXIEZOOM

• Mount bracket

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Auto show

3. 5 Static mode

3. 6 White presets mode

3. 7 Manual mode

3. 8 Master/Slave mode

3. 9 Linking

3. 10 DMX mode

3. 11 DMX addressing

3. 12 Connection of the DMX line

3. 13 Construction of the DMX termination

3. 14 DMX control

3. 15 Dimmer

3. 16 Back light

3. 17 Fixture information

3. 18 LED frequency

3. 19 Temperature

3. 20 Fan mode

3. 21 White balance

3. 22 KeyLock

3. 23 RDM

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

PIXIEZOOM

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 40 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

PIXIEZOOM

- 1 - INTRODUCTION

PIXIEZOOM is a single-source LED PAR featuring a 6°- 50° linear zoom and a fully homogenised output. Its

IP65 housing and solid build allow it to be used in any event from theaters to festivals.

FEATURES:

• Single 60W RGBW LED source delivers an even beam and full colour spectrum

• Wide linear zoom from 6° to 50°

• IP65 rating allowing for exible use

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 60 W RGBW Osram LEDs

• Luminous Flux: 1001 lm

• Lux: (6°) 7650 lux @3m Full

• Lux: (40°) 590 lux @3m Full

• Source Life Expectancy: >50.000 h

OPTICS

• Zoom: 6-40 ° Motorised linear zoom

• Lens Diameter: 100 mm

• Lens Type: HQ glass lens optics

COLOR SYSTEM

• Color Mixing: RGBW/FC

• CTC: CTC control through independent DMX channel

• White Presets:2000~8000 K

• Color Wheel: Virtual color wheel with presets

DYNAMIC EFFECTS

• Static Color Mode: Selection of static color

• Manual Color Mode: Manual adjustment of color

• Auto Mode: Built-in programs with execution speed adjustment

BODY

• Body: Sturdy die-cast aluminium body conceived for long-time durability

• Body Color: Black

CONTROL

• Protocols: DMX512, RDM

• Dmx Channels:5/7/11 ch

• RDM: RDM ready for xture remote monitor and settings

• Display: Black OLED touch display

• Firmware Upgrade: Yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: Linear 0~100% electronic dimmer

• Dimmer Curves:4 Dierent dimming curves available

PIXIEZOOM

182

259 400

lluminan

ce at a Distance

6°

- 40°

1.0m

3.0m

5.0m

7.0m

10.0m

0.17/1.15m

0.34/2.30m

0.52/3.46m

0.69/4.61m

Lux Center Beam Angle: 6°-

40°

Beam Width

68850/5310lx

7650/ 590lx

2761,7/212,4

0.87/5.77m

1406,2/108,4

688,5/

53,1

Fig.1

Technical drawing

Photometric data

• Strobe/Shutter:1-28 Hz, electronic

• Battery Backup: Battery backup for user operation without connecting to the main power

• Operating Temperature: -20/45°

• Flicker: Flicker free operation

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V):97 W

• Power consumption (at 120V):100 W

• Output (at 230V):22 units on a single power line

PHYSICAL

• Cooling: pressure and temperature balance through GORE membrane vents

• Sospension and xing: double hanging bracket suitable for safe hanging and for oor positioning

• Signal connection: Seetronic XLR 5p IN/OUT connectors

• Power connection: Seetronic powerKon waterproof IN/OUT connectors

• IP rating:65 for outdoor installations

• Dimensions (WxHxD):259x182x400 mm

• Weight:5.5 kg

PIXIEZOOM

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. SCREW for the mounting bracket

2. MOUNTING BRACKET

3. DMX IN (5-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

4. CONTROL PANEL with display and 4 buttons

used to access the control panel functions

and manage them

5. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

Rear panel Fig.2

6. POWER IN (PowerCON TRUE IN): for

connection to a socket (100-240V~/50-60Hz)

via the supplied mains cable

7. GORE: GORE membrane vents for pressure

and temperature balance

8. POWER OUT: connect to supply power to the

next unit

9. SAFETY RING to attach safety cable

79 8

PIXIEZOOM

- 2 - INSTALLATION

2.1 MOUNTING

PIXIEZOOM may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the screw to slightly release or tighten the locking mechanism of the

bracket if is necessary (2).

Fig.3

PIXIEZOOM

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel touch buttons located directly underneath the black

OLED display (g.4).

Fig.4 - Functions of the buttons

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

Mode

Enter

Down

PIXIEZOOM

3.3 MENU STRUCTURE

1 DMX Address

1 - 512 Default: 001

DMX Channel

5 Ch

Default: 11 ch7 Ch

11 Ch

Static

Fixed Color

R RW

Default: RGBW

G GW

B BW

W RGW

GB RBW

RB GBW

RG RGBW

RGB

White Presets

2000 K R=250, G=180, B=0, W=50

3000 K R=255, G=220, B=0, W=130

4000 K R=235, G=210, B=0, W=255

5000 K R=215 G=210, B=60, W=255

6000 K R=195, G=210, B=80, W=255

7000 K R=185 G=210, B=90, W=255

8000 K R=170, G=210, B=105, W=255

Manual Color

Red (0-255)

Default: RGBW=255

Green (0-255)

Blue (0-255)

White (0-255)

Auto Show

Auto 1

Speed (0-100)

Default:

AUTO1

SPEED=100

Auto 2

Speed (0-100)

Auto 3

Speed (0-100)

Auto 4

Speed (0-100)

Auto 5

Speed (0-100)

5 Zoom

Zoom (0-255) Default: 000

6 Zoom Oset

Oset (0-255)

Master/Slave

Master

Default: Slave

Slave

8 Full On

Studio

Default :HB

PIXIEZOOM

3.4 AUTO SHOW

If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show pro-

gramme provided that the blackout mode is switched o:

• Press the MENU button so many times until the display shows Auto Show, then press the ENTER button.

• Press the UP/DOWN button to switch between the show Auto 1 - Auto 5. The unit will operate in show

mode.

• Using the UP/DOWN button to select the desired run speed slow-fast 0-100.

• Press the ENTER button to save the setting.

IMPORTANT: Programs Auto 1 - 5 are fully pre-programmed and will not be altered by changes.

9 Dimmer Mode

O

Default: OFF

Dimmer 1

Dimmer 2

Dimmer 3

10 White Balance

O

Manual Red (125-255)

Default: RGBW = 255

Green (125-255)

Blue (125-255)

White (125-255)

11 LED Frequency

600 Hz

Default: 1200Hz

1200 Hz

2000 Hz

4000 Hz

25 KHz

12 Fan Mode

Auto Speed

Default: Auto Speed

High Speed

Silent

13 Back Light

Default: On

10 S

20 S

30 S

13 Key Lock

Default: On

O

15 Information

Fixture Hours

9999h

Version

V1.0

UID

15D00207****

16 Reset Factory

YES

PIXIEZOOM

3.5 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the MENU button so many times until the display shows Static, then press the ENTER button.

• Select Fixed Color through the UP/DOWN buttons, then press ENTER.

• Set the colors R , G , B, W, GB, RB, RG, RGB, RW, GW, BW, RGW, RBW, GBW, RGBW through the UP/DOWN buttons,

then press ENTER.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.6 WHITE PRESETS MODE

The white presets mode allow you to choose a preprogrammed white color temperature.

• Press the MENU button so many times until the display shows Static, then press the ENTER button.

• Select White Presets through the UP/DOWN buttons, then press ENTER.

• Choose the white color temperature through the UP/DOWN buttons, then press ENTER.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.7 MANUAL MODE

This mode allows to combine the colors red, green, blue and white (R, G, B, W).

• Press the MENU button so many times until the display shows Static, then press ENTER.

• Select Manual Color through the UP/DOWN buttons, then press ENTER.

• Select the color R, G, B, W through the UP/DOWN buttons, then press ENTER.

• Using UP/DOWN buttons, select the desired color value 000 - 255.

• Press ENTER button to continue to the next color R, G, B,W.

• Continue until the desired mix is obtained.

• Press the button MENU to go back or to meet the waiting time to exit the setup menu.

3.8 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Press the MENU button so many times until the display shows Master/Slave, then press ENTER.

• Using UP/DOWN buttons, select the desired mode and then press ENTER.

• Press the button MENU to go back or to meet the waiting time to exit the setup menu

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

• Set on master xture the desired program (see section 3.4).

• Set the slaves to the same DMX modes.

3.9 LINKING

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

PIXIEZOOM

. . . . . . . . . . . .

DMX512 Controller

DMX Address: 33 DMX Address: 48DMX Address: 38 DMX Address: 43

Fig.5 - Example 5 DMX channels conguration

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

5 33 33-37 38 43 48

3.10 DMX MODE

• Press the MENU button so many times until show Dmx Channel and press ENTER to conrm.

• Press the button UP/DOWN to select the desired DMX mode 5 Ch, 7 Ch o 11 Ch. Press ENTER button to

store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

The tables on page 14 indicate the operating mode and DMX value.

3.11 DMX ADDRESSING

• Press the MENU button so many times until show Dmx Address and press ENTER to conrm.

• Press the button UP/DOWN to select the desired DMX address 001 - 512. Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the PIXIEZOOM with a light controller, adjust the DMX start address for the rst a DMX

channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX chan-

nel, adjust the start address 33 on the PIXIEZOOM. The other functions of the light eect panel are then

automatically assigned to the following addresses.

An example with the start address 33 is shown below:

PIXIEZOOM

Fig.6

Fig.7

3.12 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.13 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

PIXIEZOOM

3.14 DMX CONTROL

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

ZOOM

0~100% 000 - 255

11 CHANNELS

MODE

FUNCTION DMX

Value

11 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

7 CHANNELS

MODE

FUNCTION DMX

Value

7 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

STROBE

No Function (shutter open)

Slow to fast

No Function (shutter open)

Random slow to fast

No Function (shutter open)

000 - 030

031 - 100

101 -130

131 - 200

201 - 255

ZOOM

0~100% 000 - 255

11 CHANNELS

MODE

FUNCTION DMX

Value

11 Ch

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

STROBE

No Function (shutter open)

Slow to fast

No Function (shutter open)

Random slow to fast

No Function (shutter open)

000 - 030

031 -100

101 - 130

131 - 200

201 - 255

ZOOM

0~100% 000 - 255

COLOR FUNCTION

No Function

Color presets

White presets

Color macro

000 - 010

011 - 085

086 - 170

171 - 255

COLOR PRESETS

RGB 100%, 0~100%, 0%

RGB 0~100%, 100%, 0%

RGB 0%, 100%, 0~100%

RGB 0%, 0~100%, 100%

RGB 0~100%, 0%, 100%

RGB 100%, 0%, 0% ~ 100%

RGB 100%, 0% ~ 100%, 0% ~ 100%

RGB 100% ~ 0%, 100% ~ 0%, 100%

RGBW

0%~100%,0%~100%, 100%, 0%~100%

000 - 028

029 - 056

057 - 084

084 - 112

113 - 140

141 - 168

169 - 196

197 - 224

225 - 255

WHITE PRESETS

2000K ~ 3000K (R=250, G=180, B=0, W=50)

3000K ~ 4000K (R=255, G=220, B=0, W=130)

4000K ~ 6000K (R=235, G=210, B=0, W=255)

6000K ~ 8000K (R=195, G=210, B=80, W=255)

8000K (R=170, G=210, B=105, W=255)

000 - 195

196 - 210

211 - 225

226 - 240

241 - 255

COLOR MACRO

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

Auto Program 5

000 - 060

061 - 110

111 - 160

161 - 210

211 - 255

COLOR MACRO SPEED

Color macro speed slow to fast 000 - 255

DIMMER FADE

Preset dimmer speed from display menu

0~100%

000 - 000

000 - 255

PIXIEZOOM

3.15 DIMMER

• To enter dimmer mode and choose to simulate dierent dimming curves, press the MENU button re-

peatedly until the display shows Dimmer Mode, then press the ENTER button.

• Press the MENU button repeatedly until Dimmer Mode shows, and press ENTER button to accept.

• Use the UP/DOWN buttons to select a dimmer curve O - Dimmer1 - Dimmer2 - Dimmer3.

• Press ENTER button to accept.

• Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3.16 BACK LIGHT

• To activate backlight display press the button MENU so many times until shows Back Light, and press the

ENTER button to conrm.

• Press the UP/DOWN buttons to select On - 10S - 20S - 30S. Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3.17 FIXTURE INFORMATION

1. Press the MENU button so many times until shows Information, and then press ENTER button.

2. Use UP/DOWN button to select: Fixture Hours - Version - UID.

3. Press ENTER button to conrm the selection.

4. Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

Fixture Hours

This option shows the user the amount of hours the PIXIEZOOM has been in use throughout its life-

time. Select Fixture Hours.

Version

This option shows the user the software version currently installed in the unit. Select Version.

UID

This option shows the RDM identication number (see paragraph 3.23)

3.18 LED FREQUENCY

• To adjust the frequency of the LEDs, press the MENU button repeatedly until the display shows LED

Frequency, and then press the ENTER button.

• Select the frequency 600 Hz - 25 KHz using the UP/DOWN buttons.

• To conrm, press the ENTER key.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

3.19 TEMPERATURE

• To read the value of the internal temperature of the device, press the MENU button repeatedly until the

display shows Temperature, and then press the ENTER key to read the value.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

PIXIEZOOM

3.20 FAN MODE

To set the rotation speed of the fans refer to the following guide:

• Press the MENU key repeatedly until the display shows Fan Mode, then press the button ENTER.

• Select by pressing UP/DOWN one of the following options: Auto - High. It is possible choose the speed of

rotation of the fans from: fast High and automatic Auto.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

3.21 WHITE BALANCE

Enter the White balance to adjust the Red, Green, Blue and White parameter to make dierent whites.

• Press the button MENU so many times until shows White Balance, and press the button ENTER to conrm.

• Select the color R, G, B, W through the buttons UP/DOWN, then press the button ENTER.

• Using UP/DOWN button, select the desired color value 125 - 255.

• Press ENTER button to continue to the next color R, G, B, W.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.22 KEY LOCK

Enter the Key Lock mode to select whether the access password is on or o.

• Press the button MODE so many times until show Key Lock and press the button ENTER to conrm.

• Use UP/DOWN button to select: ON or OFF.

• Press ENTER button to conrm the selection.

When the xture is set as pass ON, after 30 seconds or turn on the xture next time, the xture will need

an access password to enter the display menu control.

NOTE - The factory access password is UP + DOWN + UP + DOWN (press ENTER to conrm the access).

3.23 RDM - Remote Device Management

With this function you can call up various submenus via RDM.

This device is RDM ready. RDM stands for “Remote Device Management” and makes remote control of

devices connected to the DMX-bus possible. Manual settings like adjusting the DMX starting address are

no longer needed. This is especially useful when the device is installed in a remote area. RDM is integrated

in DMX without inuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1

and 2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated

in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not inuence

conventional devices. If DMX splitters are used and RDM control is to be used, these splitters must sup-

port RDM. The number and type of RDM parameters depend on the RDM controller (not included) is used.

PIXIEZOOM

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly • Clean the xture regularly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.003-12/18

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

La pagina sta caricando ...

ProLights PIXIEZOOM Manuale utente

Marca: ProLights

Modello: PIXIEZOOM

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights PIXIEZOOM User manual

Documenti correlati

Altri documenti

STUDIO DUE PARLED 300 PRO RGBW IP20 Manuale utente