Evolution COMPACT110V Manuale utente

COMPACT24HP

COMPACT110V COMPACT230V COMPACT230VEU

PUBLISHED DATE: 01/03/2016

V3

®

Original Instruction Manual

Original Bedienungshandbuch

Manual de instrucciones

Manuel d’utilisation

Manuale di istruzioni originale

2

www.evolutionpowertools.com

Model Speciﬁcations

Evolution Power Tools reserves the right to

make improvements and modiﬁcations to the

design and technical speciﬁcation of this

product without prior notiﬁcation.

This manual was originally written in English.

GB

HULK PETROL ENGINED COMPACTOR

Engine Type Single cylinder 4 stroke OHV

Engine Power (HP) 2.4 @ 3600 min

-1

Spark Plug Replacement LD E6TC (available from Evolution)

NGK BP6HS

CHAMPION L87YCC

AC DELCO 42FS

Spark Plug Gap 0.028 – 0.031 inches

0.07 – 0.08 mm

Air Filter Replacement Evolution H1S58

Valve Clearances (cold) Inlet 0.15 mm 0.006 inches

Exhaust 0.20 mm 0.008 inches

Compaction Force (kN) 10

Vibration (m/sec

2

) 15.12 K = 1.5

Sound Power Level (LwA) 101 dB(A) K= 3 dB(A)

Sound Pressure Level (LpA) 105 dB(A) K= 3 dB(A)

Recommended Maximum 20

Operator Usage Time (mins)

Oil Type SAE 10W-30/40

Oil Capacity (litres) 0.25

(pints) 0.5 (US)

Fuel Type Standard Unleaded Petrol/Gasoline

Fuel Capacity (litres) 1.2

(pints) 2.5 (US)

Weight (kg) (lb) 38 84

Handle Height (during operations - 1020 (40)

extension handle ﬁtted) mm (inches)

Machine Reach (during operations – 1290 (51)

extension handle ﬁtted) mm (inches)

Footprint Width mm (inches) 320 (12-1/2)

HULK ELECTRO COMPACTOR

Motor 230V or 115V 50/60 Hz 130W

Motor Speed (min

-1

) 2860 (no load)

Compaction Force (kN) 5

Recommended Maximum 30

Operator Usage Time (mins)

Sound Power Level (LwA) 98.8 dB(A) K= 3 dB(A)

Sound Pressure Level (LpA) 94 dB(A) K= 3 dB(A)

Vibration (m/sec

2

) 7.43 K = 1.5

Weight (kg) (lb) 26 57

Handle Height (during operations) mm (inches) 920 (36)

Machine Reach (during operations) mm (inches) 1290 (51)

Footprint Width mm (inches) 320 (12-1/2)

Cable Length Metres (Feet) 10 (33)

Insulation Class II

IP44

3

www.evolutionpowertools.com

IMPORTANT

Please read these operating and safety

instructions carefully and completely.

For your own safety, if you are uncertain

about any aspect of using this equipment

please access the relevant Technical Helpline,

the number of which can be found on the

Evolution Power Tools website. We operate

several Helplines throughout our worldwide

organization, but Technical help is also

available from your supplier.

WEB www.evolutionpowertools.com/register

Congratulations on your purchase of an

Evolution Power Tools Machine. Please

complete your product registration ‘online’

as explained in the A5 online guarantee

registration leaﬂet included with this

machine. You can also scan the QR code

found on the A5 leaﬂet with a Smart

Phone. This will enable you to validate your

machine’s guarantee period via Evolutions

website by entering your details and thus

ensure prompt service if ever needed. We

sincerely thank you for selecting a product

from Evolution Power Tools.

EVOLUTION LIMITED GUARANTEE.

EVOLUTION POWER TOOLS RESERVES

THE RIGHT TO MAKE IMPROVEMENTS

AND MODIFICATIONS TO THE PRODUCT

DESIGN WITHOUT PRIOR NOTICE.

PLEASE REFER TO THE GUARANTEE

REGISTRATION LEAFLET AND/OR THE

PACKAGING FOR DETAILS OF THE TERMS

AND CONDITIONS OF THE GUARANTEE.

Evolution Power Tools will, within the

guarantee period, and from the original date

of purchase, repair or replace any goods found

to be defective in materials or workmanship.

This guarantee is void if the tool being returned

has been used beyond the recommendations

in the Instruction Manual or if the machine

has been damaged by accident, neglect, or

improper service. This guarantee does not

apply to machines and / or components which

have been altered, changed, or modiﬁed

in any way, or subjected to use beyond

recommended capacities and speciﬁcations.

Electrical components are subject to respective

manufacturers’ warranties. All goods returned

defective shall be returned prepaid freight

to Evolution Power Tools. Evolution Power

Tools reserves the right to optionally repair or

replace it with the same or equivalent item.

There is no warranty – written or verbal – for

consumable accessories such as (following list

not exhaustive) blades, cutters, drills, chisels

or paddles etc. In no event shall Evolution

Power Tools be liable for loss or damage

resulting directly or indirectly from the use

of our merchandise or from any other cause.

Evolution Power Tools is not liable for any

costs incurred on such goods or consequential

damages. No ofﬁcer, employee or agent of

Evolution Power Tools is authorized to make

oral representations of ﬁtness or to waive any

of the foregoing terms of sale and none shall

be binding on Evolution Power Tools.

Questions relating to this limited

guarantee should be directed to the

company’s head ofﬁce, or call the

appropriate Helpline number.

POWER TOOL GENERAL SAFETY

INSTRUCTIONS

(These General Power Tool Safety Instructions

are as speciﬁed in BS EN 60745-1:2009 &

EN 61029-1:2009)

WARNING: Read all safety

warnings and instructions.

Failure to follow the warnings and instructions

may result in electric shock, ﬁre and/ or

serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

4

www.evolutionpowertools.com

1) General Power Tool Safety Warnings

[Work area safety]

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gasses or dust. Power tools

create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away

while operating power tool. Distractions can

cause you to lose control.

2) General Power Tool Safety Warnings

[Electrical Safety]

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce the risk of electric shock.

b) Avoid body contact with earthed

or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is

an increased risk of electric shock if your body

is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply. Use

of an RCD reduces the risk of electric shock.

3) General Power Tool Safety Warnings

[Personal Safety].

a) Stay alert, watch what you are doing

and use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the inﬂuence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust masks, non-skid

safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and or battery

pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the

switch or energising the power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A wrench

or key left attached to a rotating part of a

power tool may result in personal injury .

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure that these are

connected and properly used. Use of dust

collection can reduce dust-related hazards.

4) General Power Tool Safety Warnings

[Power tool use and care].

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job better

and safer at a rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on or off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the power tool from

the power source and/or battery pack

from the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventative

safety measures reduce the risk of starting the

power tool accidentally.

5

www.evolutionpowertools.com

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

Instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of moving parts and any other

condition that may affect the power tools

operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended could

result in a hazardous situation.

5) General Power Tool Safety Warnings

[Service]

a) Have your power tool serviced by a

qualiﬁed repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR HULK-

SYSTEM PETROL ENGINE

a. Petrol or diesel powered engines must

never be used in unventilated closed spaces.

The exhaust fumes produced are highly

toxic and can cause ‘Carbon Monoxide

Poisoning’ which will cause drowsiness and

ultimately death. It is only permissible to run a

petrol engine indoors if the building can be very

well ventilated and the exhaust fumes can be

captured and ducted to the outside through an

exhaust extraction/scavenger system.

b. The engine should not be run at speeds

that exceed the maximum speed on the

rating plate. Operating an engine at excessive

speeds increases the likelihood of component

failure and consequent accidents.

c. Do not tamper with components that

regulate the engines speed. You may alter

the factory set running parameters.

d. Use only the type of fuel listed in this

Instruction Manual. Using fuel with an

octane rating less than that speciﬁed can

lead to excessive engine wear and premature

engine failure.

e. Keep the area around the engine clear,

clean and tidy. Never allow any combustible

material (timber, plastic, cardboard, canvas

etc) near a running engine.

f. Do not use in or near to potentially

explosive atmospheres. Dust laden

atmospheres as can be found in some

industrial buildings (Flour Mills, Timber Mills)

have an explosive potential.

g. Regularly check the fuel system for

leaks. Hoses and unions should be checked

for deterioration or chaﬁng. Check the fuel tank

for damage or for a poorly ﬁtting or worn fuel

cap. Any defects must be rectiﬁed before the

engine is used.

h. Always stop the engine and allow it to

cool down before refuelling. Try to avoid any

fuel spillage (often caused by ‘overﬁlling’ the

tank) and clean up any spilt fuel immediately.

The application of dry sand is an effective way

of neutralising fuel spills. Do not allow sand to

come into contact with any part of the engine.

i. When transporting the engine in a

vehicle ensure that the fuel tap is turned

off. To minimise the risk of fuel spillage the

engine should be secured by ropes etc to the

load area of the vehicle so that it cannot move

during transportation. The engine should be

secured in as level an attitude as possible.

j. For long term storage we recommend

that the fuel system of the engine is

drained. During long term storage additives in

modern fuels can precipitate from the fuel and

block jets and valves in the fuel system.

k. Store the machine in a secure and well

ventilated area. Unauthorised personnel

should not have access to this machine.

SAFETY INSTRUCTIONS FOR FUEL FILLING

a. Select level bare ground, remote from

any buildings as a refuelling station. Ensure

that there is no combustible material in the

immediate vicinity.

6

www.evolutionpowertools.com

b. Smoking, using a naked ﬂame or

producing sparks is strictly forbidden

whilst refuelling. Petrol is highly ﬂammable

and its vapours are combustible.

c. Ensure that the fuel tap is turned ‘off’.

This will ensure that fresh fuel does not ‘ﬂood’

the engines carburettor.

d. The engine must be turned ‘off’ and

allowed to cool before refuelling is

attempted. Inadvertent fuel spillage onto a

hot engine can result in the risk of ﬁre.

e. Any fuel spills must be dealt with

immediately. If petrol contaminates any

clothing the operator must change clothes.

Do not rely on the fuel evaporating from the

clothes. Wash or launder the clothing when

the fuel has evaporated from the material.

f. The use of a funnel during refuelling is

recommended. Use of a funnel will minimise

the risk of fuel spillage.

g. Fill the tank with the correct grade of

unleaded fuel to a level approximately

half way up the fuel ﬁlter. Pour the fuel into

the tank carefully and do not try to ﬁll the tank

completely. Pour the petrol slowly to avoid air

traps during ﬁlling that could cause fuel spillage.

h. Check the fuel tank cap, and replace as

soon as refuelling is completed. The cap

has a bayonet type connection. Check that it

is correctly installed and seated before slowly

turning on the fuel tap.

i. Check for any fuel leaks throughout the fuel

system. Do not attempt to start the engine if a

fuel leak is suspected. Any detected leak must be

repaired by a suitably qualiﬁed technician.

j. Observe all national and/or local

regulations about the storage and use

of petroleum products. All local bye laws

should be observed.

HEALTH ADVICE

WARNING: When using this machine,

dust particles will be produced. In some

instances, depending on the materials you

are working with, this dust can be particularly

harmful. You are advised to consider the risks

associated with the materials you are working

with and to reduce the risk of exposure. As

some materials can produce dust that may be

hazardous to your health, we recommend the

use of an approved face mask with replaceable

ﬁlters when using this machine.

You should always:

• Work in a well-ventilated area.

• Work with approved safety equipment,

such as dust masks that are specially

designed to ﬁlter microscopic particles.

WARNING: the operation of any power

tool can result in foreign objects being

thrown towards your eyes, which could result

in severe eye damage. Before beginning power

tool operation, always wear safety goggles or

safety glasses with side shield or a full face

shield where needed.

WARNING: If any parts are missing,

do not operate your machine until the

missing parts are replaced. Failure to follow

this rule could result in serious personal injury.

ADDITIONAL SAFETY RULES FOR

HULK COMPACTOR

a. Cordon off the work area. Members of the

public and unauthorised personnel should be kept

at a safe distance from compacting operations.

b. Be completely sure that you know how

to switch the machine ‘off’. If you get into

difﬁculty during compacting operations it is

important that you can perform an emergency

shutdown of the machine.

c. Never leave the Hulk running and

unattended. The machine vibrates as soon

as it is started, and will also begin to move

forwards. The machine must be shutdown if it

is left unattended.

d. Always switch the engine ‘off’ before

moving the machine around the site. When

moving or transporting the machine the engine

must be switched ‘off’ and preferable cold,

with the fuel tap in the ‘off’ position.

e. As the Hulk engine becomes hot during

use ensure that you do not touch the

engine or allow any combustible material

or clothing to contact the engine during

use. Only touch or service a cold engine.

f. Never remove, alter or tamper with any of

the machines guards. The guards are specially

designed and ﬁtted to provide you with the

7

www.evolutionpowertools.com

greatest possible protection during operations.

If a guard is missing or damaged do not use the

machine until the guard is repaired or replaced

by a competent technician.

g. Be especially careful to maintain control

when working on a sloping surface. Work

up and down a sloping surface not across it.

h. Where there are a number of different

layers to be compacted on top of each

other, compact each layer separately. This

will ensure the integrity of each layer.

i. Work the Hulk over the work surface

in an organised pattern until the desired

compaction is achieved. This ensures the

safest working practice is maintained.

j. Always carry out the pre-use safety

checks before starting operations. Follow

the guidance in later sections of this Manual.

PPE (Personal Protective Equipment)

Note: If using this equipment on a construction

site it is important that the operator conforms

to any site rules/regulations that may apply.

Consult the site foreman or other responsible

person for details.

a. Wear suitable clothing. This could include

a Boiler Suit or Padded Coverall and Hi Vis

jacket etc.

b. Wear suitable footwear. Safety shoes

with steel toecaps and anti-slip soles are

recommended.

c. Wear suitable Safety Glasses. A Full Face

Safety Shield or Safety Goggles with side

shields which provide protection from thrown

debris is recommended.

d. Protect you hearing. Wear suitable ear

protectors.

e. Wear suitable gloves. High grip gloves are

recommended.

f. Wear respiratory protection. A dust

mask with replaceable ﬁlters which provide

protection against ﬁne toxic dust, ﬁbres and

vapours is recommended.

g. Wear a Safety Helmet. The use of a Safety

Hat may be compulsory on construction sites

to protect the operator from potential overhead

dangers.

VEHICULAR TRANSPORTATION

WARNING: This machine requires at

least a two man lift.

Prepare the vehicle in advance so that it is

ready to receive the machine. Take great care

to ensure that the machine is not dropped

during loading/unloading.

• Although compact, this machine is heavy. To

reduce the risk of injury, get competent help

whenever you have to lift this machine.

• To reduce the risk of back injury, hold the

machine close to your body when lifting.

Bend your knees so you can lift with your

legs, not your back. Lift by using convenient

areas of the main external frame.

• Lift the machine into the vehicle and secure

in as level an attitude as possible with ropes,

tie down straps etc so that the machine

cannot move during transportation.

Note: Hulk Petrol: It is best and safest practice

when transporting this machine in a vehicle

that there should be no fuel present in the

machines fuel tank.

INTENDED USE OF THIS POWER TOOL

WARNING: This product is a powered

Compaction Plate and has been designed

to be used with special Evolution accessories.

Only use accessories designed for use with

this machine and/or those recommended

speciﬁcally by Evolution Power Tools Ltd.

This machine can be used to compact surfaces

such as crusher run, small aggregates, soil,

sand and sub base materials etc. When ﬁtted

with the Paving Pad, the Hulk can be used to

compact and settle most types of block paving.

8

www.evolutionpowertools.com

Reasons for Compaction

Disturbed soil, new inﬁll, subbase or blacktop

will have air pockets and small voids within,

which, if not compacted can lead to possible

problems developing.

• As trafﬁc crosses the surface of an

uncompacted area, the loads imposed

press downwards on the material

underneath. This can lead to subsidence

of the top surface as material migrates

downwards to ﬁll the voids.

• A static load (house, garage etc) built

upon uncompacted ground could suffer

subsidence as material beneath it moves.

• Water seeping into material that contains

voids and air pockets can collect in these

spaces and will expand during freezing

conditions and contract again during warm/

dry spells. Expansion and contraction is a

major contributory factor causing damage

to building foundations, and can lead to a

structure needing underpinning.

Compaction increases the density of the

material and hence its ability to withstand static

and dynamic loads. Eliminating air pockets

and small voids reduces the chances of water

ingress collection and subsequent subsidence

due to material expansion and contraction.

PROHIBITED USE OF THIS POWER TOOL

WARNING: This product is a powered

Compaction Plate and must only be

used as such. It must not be modiﬁed in any

way, or used to power any other equipment or

drive any other accessories other than those

mentioned in this Instruction Manual.

WARNING: This machine is not intended

for use by persons (including children) with

reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning the safe use of the machine by a

person responsible for their safety.

Children should be supervised to ensure

that they do not have access to, and are not

allowed to play with, this machine.

ELECTRICAL SAFETY – HULK ELECTRO

THE MAINS PLUG

This product is ﬁtted with the correct moulded

plug for the designated sales market. The

plug meets the requirements of international

standards, and must be connected to a supply

voltage that is equal to that stated on the

rating label. If the plug or mains supply lead are

damaged they must be replaced with a complete

assembly that is identical to the original. Adhere

to the requirements for mains electricity supply

connection that applies in your Country. If in

doubt consult a qualiﬁed electrician.

BS plug can only be used in the UK. The plug

should be plugged into the socket indoor to

fulﬁl the required IP protection degree. The plug

should be incorporated with a power cord longer

than 10m.

OUTDOOR USE – HULK ELECTRO

WARNING: For your protection if this tool

is to be used outdoors it should not be

exposed to rain, or used in very damp locations.

For added protection use a residual current device

(R.C.D.) that will interrupt the supply if the leakage

current to earth exceeds 30mA for 30ms. Always

check the operation of the residual current device

(R.C.D.) before using the machine.

If an extension cable is required it must be a

suitable type for use outdoors and so labelled.

The manufacturers instructions should be

followed when using an extension cable.

9

www.evolutionpowertools.com

VIBRATION

WARNING: When using this machine

the operator can be exposed to high

levels of vibration transmitted to the hand

and arm. It is possible that the operator

could develop “Vibration white ﬁnger

disease” (Raynaud syndrome). This condition

can reduce the sensitivity of the hand to

temperature as well as producing general

numbness. Prolonged or regular users of

compacting machines should monitor the

condition of their hands and ﬁngers closely.

If any of the symptoms become evident, seek

immediate medical advice.

• The measurement and assessment of

human exposure to hand-transmitted

vibration in the workplace is given in:

BS EN ISO 5349-1:2001 and

BS EN ISO 5349-2:2002

• Many factors can inﬂuence the actual

vibration level during operation e.g. the

work surfaces condition and orientation

and the type and condition of the machine

being used. Before each use, such factors

should be assessed, and where possible

appropriate working practices adopted.

Managing these factors can help reduce

the effects of vibration:

Handling

• Handle the machine with care, allowing

the machine to do the work.

• Avoid using excessive physical effort on

any of the machines controls.

• Consider your security and stability, and

the orientation of the machine during use.

Work Surface

• Consider the work surface material;

its condition, density, strength,

rigidity and orientation.

SYMBOLS AND LABELS

WARNING: Do not operate machine

if warning and/or instruction labels are

missing or damaged. Contact Evolution Power

Tools for replacement labels.

Note: All or some of the following symbols

may appear in the manual or on the product.

Read the Manual

Wear Ear Protection

Wear Eye Protection

Wear Dust Protection

Warning

CAUTION:

Hot exhaust

Do not touch

CAUTION: This is a

4 stroke engine.

Fill with petrol only.

Do not ﬁll with

diesel oil.

Allow motor to cool

before opening

the fuel cap. The

vapour is extremely

ﬂammable and may

ignite on contact with

a hot surface

or ﬂames.

UNLEADED

PETROL ONLY!

HIGHLY FLAMMABLE.

10

www.evolutionpowertools.com

MACHINE OVERVIEW HULK PETROL

1. VIBRATION PLATE

2. FUEL TANK

3. ENGINE ‘ON/OFF’ IGNITION SWITCH

4. THROTTLE LEVER

5. CHOKE CONTROL

6. RECOIL STARTER

7. FUEL TAP

8. ENGINE OIL FILLER/DIPSTICK

9. AIR FILTER

10. SPARK PLUG

11. EXHAUST

12. ENGINE OIL DRAIN PLUG

13. FAST RUN ADJUSTMENT SCREW

14. BELT GUARD

(1)

(14)

(11)

(10)

(2)

(7)

(5)

(9)

(4)

(13)

(6)

(3)

(8)

(12)

11

www.evolutionpowertools.com

MACHINE OVERVIEW HULK ELECTRO

1. VIBRATION PLATE

2. CROSSBAR/CABLE STORE

3. SAFETY START ‘ON/OFF’ SWITCH

4. ANTI-VIBRATION HAND GRIP

5. UPPER SECTION - HANDLE

6. MIDDLE SECTION - HANDLE

(1)

(2)

(3)

(4)

(5)

(6)

12

www.evolutionpowertools.com

GETTING STARTED

UNPACKING

Caution: This packaging contains sharp

objects. Take care when unpacking. This

machine could require two persons to lift,

assemble and move this machine. Remove

the machine, together with the accessories

supplied from the packaging. Check carefully

to ensure that the machine is in good

condition and account for all the accessories

listed in this manual. Also make sure that all

the accessories are complete. If any parts

are found to be missing, the machine and

its accessories should be returned together

in their original packaging to the retailer. Do

not throw the packaging away; keep it safe

throughout the guarantee period. Dispose

of the packaging in an environmentally

responsible manner. Recycle if possible. Do

not let children play with empty plastic bags

due to the risk of suffocation.

ITEMS SUPPLIED -

HULK PETROL COMPACTOR

DESCRIPTION QUANTITY

Instruction Manual 1

Handle Extension 1

Handle Extension attachment

thumb screws

4

Spark Plug Box Spanner 1

Engine Oil (500 ml bottle) 1

ITEMS SUPPLIED -

HULK ELECTRO COMPACTOR

DESCRIPTION QUANTITY

Instruction Manual 1

Handle attachment thumb

screws (long)

2

Handle attachment thumb

screws (short)

2

Handle cross bar/cable store 1

Additional Accessories

In addition to the standard items supplied with

this machine the following accessories are

also available from the Evolution online shop

at www.evolutionpowertools.com or from

your local retailer.

DESCRIPTION PART No

Hulk Paving Pad Hulk Pad

13

www.evolutionpowertools.com

Fig. 1

ASSEMBLY

Your Evolution Hulk needs some minor assembly

and some minor operator adjustments to prepare

the machine for use. If you have the petrol engined

machine complete all assembly before ﬁlling the

engine with 0.25L of the recommended service oil.

1. Attaching the Extension Handle – Hulk Petrol

Note: The Handle Extension has an anti-vibration

hand grip which helps the operator to manage the

vibration transmitted by the machine to the hand/

arm of the operator. The Extension Handle should

be ﬁtted for operational purposes, but can be

removed, if convenient, during transportation or

storage. Removing the bottom two thumb screws

and loosening the top two thumb screws allows the

handle extension to be folded forwards for ease of

transportation.

• Carefully slide the Extension Handle over the main

operating handle and align the four (4) holes in the

Extension Handle with the four (4) captive nuts in

the main handle.

• Insert the four (4) ø10 mm thumb screws through

the Extension Handle holes and into the captive

nuts. (Fig. 1)

• Tighten all four (4) thumb screws securely.

2. Assembling/attaching the Handle – Hulk Electro

Note: The Hulk Electro Handle consists of four (4)

main parts:

• Lower handle (pivoting and factory attached to the

machine).

• Middle section.

• Upper section with ‘On/Off’ safety switch.

• Cross-bar/cable store.

The two long thumb screws are used to attach the

cross-bar/cable store and the middle section of the

handle to the pivoting lower handles.

• Carefully position the cross-bar cable store into its

service position.

Note: The cable pins should face rearwards.

14

www.evolutionpowertools.com

• Carefully slide the Middle Section over the lower

handles and align the holes.

• Insert the long thumb screws through the holes in

the middle handle, through the holes in the lower

handles and screw them into the captive nuts in the

cross-bar/cable store. (Fig. 2)

• Tighten these screws securely.

The two (2) short thumb screws are used to attach the

Upper Section of the handle to the Middle Section.

• Carefully slide the Upper Section of the handle over

the Middle Section and align the holes.

• Insert the thumb screws through the Upper Section

handle and screw them into the captive nuts within

the Middle Section.

WARNING: Take care to ensure that the power

cable from the Safety Switch down to the motor is

‘free’ and not ‘trapped’ during the assembly process.

Initial ﬁlling and checking the oil level –

Hulk Petrol

WARNING: This machine does not come ﬁlled

with oil. No attempt to start the engine must be

made until the crankcase is ﬁlled to the correct level

with the correct grade of oil.

Note: Oil (provided) should be poured into the

machine through the Oil Filler/Level Cap. Oil capacity

is approximately 0.25 litre of 10W 30 automotive oil

(available at all good motor factors and most petrol

stations). For some non-temperate climatic areas an

alternative grade of oil may be preferable – consult

your supplier.

The Oil Filler Cap unscrews from the machines engine

casing and incorporates an oil level dip stick. (Fig. 3)

Take care not to spill any oil.

Note: It is important that when checking the oil level

the machine is on a stable, horizontal and level surface

with the engine stopped and cold.

Two index marks are provided on the dipstick.

The oil level should be maintained at or near the

upper index mark.

Fig. 2

Fig. 3

15

www.evolutionpowertools.com

• Remove the Oil Filler/Level Cap and wipe the

dipstick with a clean dry cloth.

• Pour in the required amount of oil. (approx 0.25L)

• Allow the oil to settle for 10+ seconds.

• View the oil level through the oil ﬁller oriﬁce. The

oil level should be very near the top of the threads

with oil just about to spill out from the crankcase

(the machine must be on a level horizontal surface).

• Insert the dipstick and screw the cap fully ‘home’.

Unscrew the ﬁller cap and withdraw the dipstick.

Visually check the

oil level on the dipstick.

• Adjust as necessary.

• When the level is correct tighten the Oil Filler/Level

Cap securely into the engine casing.

Note: Change the oil according to the Maintenance

Summary Chart (Refer also to MAINTENANCE –

Engine oil replacement)

Pre – operating checks

Note: Before each operation the machine should be

inspected to ensure that all safety features etc, are

working correctly.

• Check that all safety guards are in position and

undamaged.

• Hulk Electro – Check the integrity of the power

cable and plug. If the power cable or plug is

damaged in any way the cable and/or the plug

must be replaced by a competent technician with

identical replacement parts.

• Hulk Petrol - Check all fuel hoses, unions and ﬁller

caps etc for signs of ﬂuid leakage. Any leak detected

must be repaired before operations commence.

• Check the engine oil level and adjust as necessary.

• Check the fuel level and top up as necessary.

• Thoroughly inspect the rest of the machine for

any form of damage particularly to covers, guards,

rubber components etc.

Starting the Hulk Engine

• Turn the fuel tap lever to the ‘On’ position. (Fig. 4)

• Set the choke lever to the ‘Choke On’ position.

(Fig. 5)

Fig. 4

Fig. 5

16

www.evolutionpowertools.com

• Press the engine ignition rocker switch to the ‘ON’

(I) position. (Fig. 6)

• Set the throttle lever to maximum. (Fig.7)

Note: The throttle can normally be left in this position

at all times.

• Steady the Hulk by holding the operating handle at

a convenient point.

• Use your other hand to grip the recoil starter cord

handle. (Fig. 8)

• Pull the recoil starter cord slowly until resistance is

felt indicating that the starter is engaged.

• When resistance is felt pull the cord sharply.

• Continue this procedure until the engine starts.

• Allow the engine to achieve operating temperature.

• Usually the choke can be returned to the ‘off’

(run) position almost immediately when the

engine ﬁres up, but this will depend upon ambient

temperatures, operating conditions etc. and

operator discretion will be required.

• Under some circumstances choke may be needed

even when the engine is warm from a previous

operating cycle. If you experience difﬁculty in

starting a warm engine:

• Set the choke to the ‘on’ position.

• Pull the recoil starter once.

• Return the choke to the ‘off’ (run) position.

• Pull the recoil starter until the engine ﬁres.

• Note: The Hulk will begin to vibrate and travel as

soon as the engine is started. The operator should

ensure due diligence when starting this machine.

Stopping your Hulk Petrol Engine

• Press the engine ignition rocker switch to the ‘OFF’

(0) position.

• Close the fuel tap.

Fig. 6

Fig. 7

Fig. 8

17

www.evolutionpowertools.com

Machine Travel – Hulk Petrol

Note: Adjusting the speed of the engine alters the

frequency of vibration and also the speed at which the

machine travels forwards. Adjusting the engine speed

controls should only be attempted with the engine

switched off and not running.

Note: The Fast Run Screw limits the maximum travel

of the throttle lever and thus controls maximum engine

speed only.

If you need to alter the maximum engine speed to

increase or decrease the speed of ‘travel’ of the machine:

• Turn the Fast Run Screw (Fig. 9) a little at a time (half a

turn max) clockwise to decrease the engine speed, or

counter clockwise to increase the speed of the engine.

• Ensure that the throttle is set to maximum.

• Start the machine and check the ‘travel’ of the machine

at the new Fast Run Screw setting.

• If necessary stop the machine and adjust further

the Fast Run Screw until the desired ‘travel’ speed

is achieved.

Starting and Stopping the Hulk Electro

The Hulk Electro is ﬁtted with a Safety Start ‘On/Off’

switch. The safety interlock prevents the switch lever from

being operated until the safety lock button is depressed.

• Press the safety lock button (Fig. 10) and pull the

switch lever to start the machine.

• Release the switch lever to switch off the machine.

Note: Upon release of the switch lever the motor

will stop and the safety lock button will automatically

revert to ‘safe mode’.

WARNING: The operator should always be

aware of the routing of the power cable to ensure

that it does not become a ‘trip’ or any other form of

hazard, or could be ‘run over’ by the machine.

Fig. 9

Fig. 10

18

www.evolutionpowertools.com

GENERAL OPERATING ADVICE

• Ensure that bystanders are kept at a safe distance

from compacting operations. If necessary cordon

off the work area and post WARNING notices.

• Plan your work, and the path you intend the machine

to travel, before you start compacting operations.

• Survey the working area before you begin and

remove or otherwise neutralise any obstructions/

obstacles that could pose a danger.

• Ensure you have all the correct PPE and know how

to use it.

• The compactor will travel forwards under its own

power. Gentle inputs from the operator on the

machines handle are all that is necessary to ‘steer’

the machine. The operator should hold the anti-

vibration handle grip with both hands, and the hands

should be positioned as far apart as possible.

• Several passes over the work area may be required

to compact the material to the desired density.

• If the work area is sloped, work up and down the

sloping surface, not across

MAINTENANCE

HULK PETROL

Regular maintenance is essential to keep your

machine and its accessories in serviceable condition.

We recommend that only competent operators who

have experience in servicing and maintaining petrol

engines attempt these procedures. If in doubt have

the machine serviced at an Evolution approved

Service Centre.

1. Engine oil replacement

Engine oil should be replaced after the initial

‘running in’ period and at the intervals speciﬁed

in the Service Schedule.

Note: Engine oil is easier to replace when the engine

has been run up to temperature and the oil is warm.

• Ensure that the engine is positioned on a hard level

surface.

• Remove the oil ﬁller cap. (Fig. 11)

• Place a suitable oil collection pan under the engine.

• Remove the oil drain plug so that the oil can drain

completely from the engine. (Fig. 12)

Fig. 11

Fig. 12

19

www.evolutionpowertools.com

Fig. 13

WARNING: Be careful. Contact with used

engine oil can be harmful. The oil could be very

hot (burn risk) and some operators may experience

irritation if the oil contaminates exposed skin.

The operator should consider wearing mechanics

protective gloves if available. Any skin contaminated

with oil should be washed with soap and copious

amounts of clean water as soon as possible.

• Check the oil drain plug and its gasket.

• Check the oil ﬁller cap and its ‘O’ ring gasket.

• Replace any non-serviceable parts.

• Re-install the oil drain plug and tighten ﬁrmly.

• Reﬁll the engine with the correct grade of engine oil

to the correct level.

• Reﬁt the oil ﬁller cap.

• Check for leaks and spillages, and deal with as

necessary.

Note: Used engine oil should be disposed of in an

environmentally safe way. Check with your Local

Authority for the nearest used oil re-cycling facility.

2. Spark Plug - Checking and replacement

After approximately 50 hours of operation the spark

plug should be removed for checking, cleaning and

resetting.

To remove and reinstall the spark plug:

• Ensure that the engine is switched ‘OFF’ and the

fuel tap is in the ‘OFF’ position.

WARNING: The engine should be cold before

commencing the spark plug removal procedure.

• Pull the HT lead from the spark plug.

• Using a spark plug socket (supplied) remove the

spark plug. (Fig. 13)

A serviceable spark plug in good condition should

exhibit light tan deposits on the plug nose. Remove

these deposits with a stiff brass wire brush.

• Check the electrode gap of the plug using a set of

feeler gauges.

• Adjust if necessary. The gap is given in

‘Speciﬁcation Hulk Petrol’.

• Re-install the spark plug. Be careful that it engages

the threads in the cylinder head correctly.

20

www.evolutionpowertools.com

• Hand- tighten spark the plug using the supplied

spark plug socket.

• Slide a short, suitable tommy bar through the hole

in the end of the spark plug socket.

• Position the tommy bar so that equal amounts

protrude through either side of the spark plug socket.

• Finally make the gas tight seal by turning the spark plug

socket between ¼ to ½ of a turn. This ﬁnal fractional

turn will crush the spark plug washer and make a gas

tight seal. Do not overtighten the spark plug.

• Reattach the HT lead to top of the spark plug.

3. Air Filter

WARNING: Never run the engine without the air

ﬁlter element ﬁtted.

After approximately 50 hours of use the condition of

the air ﬁlter should be checked.

Note: The air ﬁlter may require more frequent attention

if the operating environment is especially dusty.

To remove:

• Ensure that the engine is switched ‘OFF’ and the

fuel tap is in the ‘OFF’ position. The engine should

be cold.

• Unscrew the wing nuts from the Air Filter housing

cover and remove it. (Fig. 14)

• Carefully store these parts for later re-installation.

• Remove the Air Filter Element from the housing

for inspection. (Fig. 15) If the paper element of the

air ﬁlter shows signs of severe discolouration and

clogging by dirt, dust etc it should be replaced.

To reﬁt:

• Install the element into the Air Filter Housing.

A new element can ﬁt either way round.

• Replace the Air Filter housing cover.

• Replace the wing nuts and ensure that the cover

is correctly seated and the wing nuts are securely

tightened.

Fig. 14

Fig. 15

La pagina sta caricando ...

Evolution COMPACT110V Manuale utente

Questo manuale è adatto anche per

Evolution COMPACT110V Manuale utente

in altre lingue

Documenti correlati

Altri documenti