Haier 1U60IS1ERA Guida d'installazione

INSTALLATION MANUAL

SINGLE SPLIT AIR CONDITIONER

Please read this manual carefully before installation.

Keep this operation manual for future reference.

No. 0150510322 B

1U28HS1ERA

1U36HS1ERA

1U48IS1EAB

1U60IS1ERA

1U60IS1ERB

1U60IS1EAB

AU60NAIESA

1U48LS1ERA

1U48LS1ERB

1U48LS1EAB

INSTALLATION MANUAL

SINGLE SPLIT AIR CONDITIONER

Please read this manual carefully before installation.

Keep this operation manual for future reference.

Contents

English

Safety Precautions

Read Before Installation

Name of Parts

Installation Procedure

Troubleshooting

3

7

10

11

18

1U28HS1ERA

1U36HS1ERA

1U48IS1EAB

1U60IS1ERA

1U60IS1ERB

1U60IS1EAB

AU60NAIESA

1U48LS1ERA

1U48LS1ERB

1U48LS1EAB

3

Safety Precautions

Be sure to conform with the following important Safety Precautions.

Carefully read the following information in order to operate the air conditioner correctly.

If any abnormal phenomena is found

(e. g.smell of firing), please cut off

the power supply immediately, and

contact the dealer to find out the

handling method.

In such case, to continue using the conditioner will damage

the conditioner, and may cause electrical shock or fire

hazard.

Don't dismantle the outlet of the

outdoor unit.

The exposure of fan is very dangerous

which may harm human beings.

Symbols used in the illustrations

:Indicates an action that must be avoided.

:Indicates that important instructions must be followed.

:Indicates a part which must be grounded.

:Beware of electric shock (This symbol is displayed on the main unit label.)

After reading this handbook, hand it over to those who will be using the unit.

The user of the unit should keep this mamual at hand and make it available to those who will be performing repairs or

relocating the unit. Also, make it available to the new user when the user changes hands.

Below are listed three kinds of Safety Precautions and Suggestions.

Incorrect operations may result in severe consequences of death or serious injuries.

Incorrect operations may result in injuries or machine damages; in some cases may

cause serious consequences.

INSTRUCTIONS:

These information can ensure the correct operation of the machine.

After a long time use of air-conditioner

the base should be checked for any

damages.

If the damaged base is not repaired, the

unit may fall down and cause accidents.

When need maintenance and repairment,

call dealer to handle it.

Incorrect maintenance and repairment

may cause water leak, electrical shock

and fire hazard.

Air-conditioner can't be installed in the environment with

inflammable gases because the inflammable gases near

air-conditioner may cause fire hazard.

Please let the dealer be responsible for installing the

conditioner. Incorrect installation may cause water leak,

electrical shock and fire hazard.

Connect earthing wire.

Earthing wire should not be connected to the gas

pipe, water pipe, lightning rod or phone line,

incorrect earthing may cause shock.

Use discharge pipe correctly to ensure efficient discharge.

Incorrect pipe use may cause water leaking.

Installed electrical-leaking circuit breaker.

It easily cause electrical shock without circuit breaker.

Call the dealer to take measures to prevent the refrigerant

from leaking.

If conditioner is installed in a small room, be sure to take

every measure in order to prevent suffocation accident

even in case of refrigerant leakage.

When conditioner is installed or reinstalled, the dealer should

be responsible for them.

Incorrect installation may cause water leaking, electrical

shock and fire hazard.

No goods or nobody is permitted to

placed on or stand on outdoor unit.The

falling of goods and people may cause

accidents.

Don't operate the air-conditioner with

damp hands.Otherwise it will be shocked.

Only use correctly-typed fuse.

May not use wire or any other materials

replacing fuse, otherwise it may cause

faults or fire accidents.

Earthing

switch off

!

WARNING

CAUTION

WARNING

4

Safety Precautions

Have the unit professionally installed.

Improper installation by an unqualified person may result

in water leak, electric shock, or fire.

Be sure to carefully follow each step in this handbook when

installing the unit.

Improper installation may result in water leak, electric shock,

smoke or fire.

Have all electrical work performed by a licensed electrician

according to the local regulations and the instructions given

in this manual. Secure a circuit designated exclusively to

the unit.

Improper installation or a lack of circuit capacity may cause

the unit to malfunction or present a risk of electric shock,

smoke,and fire.

Place the unit on a stable, level surface that withstands the

weight of the unit to prevent the unit from tipping over or

falling causing injury as a result.

Only use specified cables for wiring. Securely connect each

cable, and make sure that the cables are not straining the

terminals.

Cables not connected securely and properly may generate

heat and cause fire.

Take necessary safety measures against typhoons and

earthquakes to prevent the unit from falling over.

Do not make any changes or modifications to the unit. In

case of problems, consult the dealer.

If repairs are not made properly, the unit may leak water

and present a risk of electric shock, or it may produce smoke

or cause fire.

Securely attach the terminal cover(panel) on the unit.

If installed improperly, dust and/or water may enter the unit

and present a risk of electric shock, smoke or fire.

Only use refrigerant R410A as indicated on the unit when

installing or relocating the unit.

The use of any other refrigerant or an introduction of air into

the unit circuit may cause the unit to run an abnormal cycle

and abnormal cycle and cause the unit to burst.

In the event of a refrigerant gas leak, provide adequate

ventilation to the room.

If leaked refrigerant gas is exposed to a heat source, noxious

gases may form.

Do not touch the fins on the heat exchanger with bare hands,

for they are sharp and dangerous.

Do not try to defeat the safety features of the devices, and

do not change the settings.

Defeating the safety features on the unit such as the pressure

switch and temperature switch or using parts other than the

dealer or specialist may result in fire or explosion.

When installing the unit in a small room, safeguard against

hypoxia that results from leaked refrigerant reaching the

threshold level.

Consult the dealer for necessary measures to take.

When relocating the air conditioner, consult the dealer or

a specialist.

Improper installation may result in water leak, electric shock,

or fire.

After completing the service work, check for a refrigerant

gas leak.

If leaked gas refrigerant is exposed to a heat source such

as fan heater,stove,and electric grill, noxious gases may

form.

Only use specified parts.

Have the unit professionally installed. Improper installation

may cause water leak, electric shock,smoke, or fire.

With All-Fresh type air conditioners, outdoor air may be

directly blown into the room upon thermo off. Take this into

consideration when installing the unit.

Direct exposure to outdoor air may present a health hazard,

and it may also cause food items to deteriorate.

Children should be supervised to ensure that they do not

play with the appliance.

WARNING

This appliance is not intended for use by persons (including

children) with reducedphysical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

5

Safety Precautions

Precautions for Handling Units for Use with R410A

Do not use the existing refrigerant piping

The old refrigerant and refrigerator oil in the existing piping

contain a large amount of chlorine, which will cause the

refrigerator oil in the new unit to deteriorate.

R410A is a high-pressure refrigerant, and the use of the

existing piping may result in bursting.

Keep the inner and outer surfaces of the pipes clean and

free of contaminants such as sulfur, oxides, dust/dirt shaving

particles,oils,and moisture.

Contaminants inside the refrigerant piping will cause the

refrigerant oil to deteriorate.

Use a vacuum pump with a reverse-flow check valve.

If other types of valves are used, the vacuum pump oil will

flow back into the refrigerant cycle and cause the refrigerator

oil to deteriorate.

Do not use the following tools that have been used with the

conventional refrigerants. Prepare tools that are for exclusive

use with R410A.

(Gauge manifold, charging hose, gas leak detector,

reverse-flow check valve, refrigerant charge base,vacuum

gauge, and refrigerant recovery equipment.)

If refrigerant and/or refrigerant oil left on these tools are

mixed in with R410, or if water is mixed with R410A, it will

cause the refrigerant to deteriorate.

Since R410A does not contain chlorine, gas-leak detectors

for conventional refrigerators will not work.

Store the piping to be used during installation indoors, and

keep both ends of the piping sealed until immediately before

brazing.(keep elbows and other joints wrapped in plastic.)

If dust, dirt, or water enters the refrigerant cycle, it may

cause the oil in the unit to deteriorate or may cause the

compressor to malfunction.

A large amount of mineral oil will cause the refrigerating

machine oil to deteriorate.

Use a small amount of ester oil, ether oil, or alkylbenzene

to coat flares and flange connections.

Use liquid refrigerant to charge the system.

Charge the unit with gas refrigerant will cause the refrigerant

in the cylinder to change its composition and will lead to

a drop in performance

Do not use a charging cylinder.

The use of charging cylinder will change the composition

of the refrigerant and lead to power loss.

Exercise special care when handling the tools.

An introduction of foreign objects such as dust, dirt or

water into the refrigerant cycle will cause the refrigerating

machine oil to deteriorate.

Only use R410A refrigerant.

The use of refrigerants containing chlorine(i.e. R22) will

cause the refrigerant to deteriorate.

Before Installing the Unit

Do not install the unit in a place where there is a possibility

of flammable gas leak.

Leaked gas accumulated around the unit may start a fire.

Do not use the unit to preserve food, animals, plants, artifacts,

or for other special purposes.

The unit is not designed to provide adepuate conditions

to preserve the quality of these items.

Do not use the unit in an unusual environment

The use of the unit in the presence of a large amount of

oil, steam, acid, alkaline solvents or special types of sprays

may lead to a remarkable drop in performance and/or

malfunction and presents a risk of electric shock, smoke,

or fire.

The presence of organic solvents, corroded gas (such as

ammonia,sulfur compounds,and acid may cause gas or

water leak.)

When installing the unit in a hospital, take necessary measures

against noise.

High-frequency medical equipment may interfere with the

normal operation of the air conditioning unit or the air

conditioning unit may interfere with the normal operation

of the medical equipment

When humidity level exceeds 80% or when the drainage

system is clogged, indoor units may drip water.

Installation of a centralized drainage system for the outdoor

unit may also need to be considered to prevent water drips

from the outdoor units.

Do not place the unit on or over things that may not get wet.

Caution

6

Safety Precautions

Before Installing (Relocating) the Unit or Performing Electric Work

Ground the unit.

Do not connect the grounding on the unit to gas pipes,water

pipes, lightning rods, or the grounding terminals of

telephones. Improper grounding presents a risk of electric

shock, smoke, fire, or the noise caused by improper

grounding may cause the unit to malfunction.

Before the Test Run

Do not operate switches with wet hands to avoid electric.

Allow for at least five minutes before turning off the unit,

otherwise the unit may leak water or experience other

problems.

Do not turn off the power immediately after stopping the unit.

If the wires are too taut, they may break or generate heat

and/or smoke and cause fire.

Make sure the wires are not subject to tension.

Install a breaker for current leakage at the power source

to avoid the risk of electric shock.

Without a breaker for current leakage, there is a risk of

electric shock, smoke or fire.

Use breakers and fuses (electrical current breaker, remote

switch<switch+Type-B fuse>,molded case circuit breaker)

with a proper current capacity.

The use of large-capacity fuses, steel wire, or copper wire

may damage the unit or cause smoke or fire.

When installing draining pipes, follow the instructions in the

manual, and make sure that they properly drain water so as

to avoid dew condensation.

If not installed properly, they may cause water leaks and

damage the furnishings.

Do not spray water on the air conditioners or immerse the

air conditioners in water.

Water on the unit presents a risk of electric shock.

Periodically check the platform on which is placed for damage

to prevent the unit from falling.

If the unit is left on a damaged plarform, it may topple over,

causing injury.

Things such as nails may be included in the package.

Dispose of them properly to prevent injury.

Plastic bags present a choking hazard to children. Tear

up the plastic bags before disposing of them to prevent

accidents.

Properly dispose of the packing materials.

Do not touch the refrigerant pipes with bare hands during

and immediately after operation.

Depending on the state of the refrigerant in the system,

certain parts of the unit such as the pipes and compressor

may become very cold or hot and may subject the person

to frost bites or burning.

Do not operated the unit without panels and safety guards

in their proper places.

They are there to keep the users from injury from

accidentally touching rotating, high-tempreture or high-

voltage parts.

Dust particles in the air may clog the system and cause

malfunction.

Do not operate the unit without air filters.

Caution

7

Read Before Installation

Tools/Materials Use Notes

Gauge Manifold Evacuating,refrigerant charging 5.09MPa on the High-pressure side.

Charging Hose Evacuating, refrigerant charging Hose diameter larger than the concentional ones.

Refrigerant Recovery Equipment Refrigerant recovery

Refrigerant Cylinder Refrigerant charging Write down the refrigerant type. Pink in color at the top of the cylinder.

Refrigerant Cylinder Charging Port Refrigerant charging Hose diameter larger than the conventional ones.

Flare Nut Connecting the unit to piping Use Type-2 Flare nuts.

Tools/Materials Use Notes

Gas leak detector Detection of gas leaks The ones for HFC type refrigerant may be used.

Vacuum Pump Vacuum drying May be used if a reverse flow check adaptor is attached.

Refrigerant Recovery Equipment Recovery of refrigerant May be used if designed for use with R410A.

Flare Tool Flare machining of piping Chages have been made in the flare machining dimension.Refer to the next page.

Tools/Materials Use Notes

Vacuum Pump with a Check Valve Vacuum drying

Bender Bending pipes

Pipe Cutter Cutting pipes

Torque Wrench Tightening flare nuts Only 12.70 (1/2'') and 15.88(5/8'') have a larger flare machining dimension.

Welder and Nitrogen Cylinder Welding pipes

Refrigerant Charging Meter Refrigerant charging

Vacuum Gauze Checking vacuum degree

Tools/Materials Use Notes

Charging Cylinder Refrigerant Charging Must not be used with R410-type units.

CAUTION

Items to Be Checked

(1). Verify the type of refrigerant used by the unit to be serviced. Refrigerant Type: R410A

(2). Check the symptom exhibited by the unit to be serviced. Look in this service handbook for symptoms relating to the

refrigerant cycle.

(3). Be sure to carefully read the safety precautions at the beginning of this document.

(4). If there is a gas leak or if the remaining refrigerant is exposed to an open flame, a noxious gas hydrofluoric acid may

form. Keep workplace well ventilated.

Install new pipes immediately after removing old ones to keep moisture out of the refrigerant circuit.

Chloride in some types of refrigerants such as R22 will cause the refrigerating machine oil to deteriorate.

Necessary Tools and Materials

Prepare the following tools and materials necessary for installing and servicing the unit.

Necessary tools for use with R410A(Adaptability of tools that are for use with R22 and R407C).

1. To be used exclusively with R410A ( Not to be used if used with R22 or R407C )

2. Tools and materials that may be used with R410 with some restrictions

3. Tools and materials that are used with R22 or R407C that can also be used with R410A

4. Tool and materials that must not used with R410A

Tools for R410A must be handled with special care, and keep moisture and dust from entering the cycle.

8

Read Before Installation

Maximum Operation Pressure Applicable Refrigerants

3.4MPa R22, R407C

4.15MPa R410A

Use pipes that meet the local standards.

Use pipes made of phosphorus deoxidized copper.

Since the operation pressure of the units that use R410A is higher than that of the units for use with R22, use pipes with

at least the radial thickness specified in the chart below. (Pipes with a radial thickness of 0.7mm or less may not be used.)

Although it was possible to use type-O for pipes with a size of up to

19.05(3/4") with conventional refrigerants, use type-

1/2H pipes for units that use R410A.(Type-O pipes may be used if the pipe size is 19.05 and the radial thickness is 1.2t.)

The table shows the standards in Japan. Using this table as a reference, choose pipes that meet the local standards.

The flare machining dimensions for units that use R410A is larger than those for units that use R22 in order to increase

air tightness.

If a clutch type flare tool is used to machine flares on units that use R410A, make the protruding part of the pipe between

1.0 and 1.5mm. Copper pipe gauge for adjusting the length of pipe protrusion is useful.

Size(mm) Radial Thickness(mm)Size(inch)

Type

Type-O pipes

Type-1/2H or Hpipes

Piping Materials

Types of Copper Pipes (Reference)

The table shows the standards in Japan. Using this table as a reference, choose pipes that meet the local standards.

Piping Materials/Radial Thickness

Flare Machining (type-O and OL only)

Flare Machining Dimension(mm)

External dimension of pipes

Size

Dimension A

R410A R22

6.35

9.52

12.7

15.88

19.05

1/4"

3/8"

1/2"

5/8"

3/4"

9.1

13.2

16.6

19.7

24.0

9.0

13.0

16.2

19.4

23.3

Flare Nut

Type-2 flare nuts instead of type-1 nuts are used to increase the strength. The size of some of the flare nuts have also

been changed.

Flare nut dimension(mm)

R410A(Type2) R22(Type1)

6.35

9.52

12.7

15.88

19.05

1/4"

3/8"

1/2"

5/8"

3/4"

17.0

22.0

26.0

29.0

36.0

17.0

22.0

24.0

27.0

36.0

6.35

9.52

12.7

15.88

1/4''

3/8''

1/2''

5/8''

0.8t

1.0t

19.05 3/4'' 1.0t

Dimension A

External dimension of pipes Size

Dimension B

9

Read Before Installation

Pressurize the equipment with nitrogen up to the design pressure and then judge the equipment's air tightness, taking

temperature variations into account.

When investigating leakage locations using a refrigerant, be sure to use R410A.

Ensure that R410A is in a liquid state when charging.

Use of oxygen as the pressurized gas may cause an explosion.

Charging with R410A gas will lead the composition of the remaining refrigerant in the cylinder to change and then this

refrigerant can not be used.

Air Tightness Test

No changes from the conventional method. Note that a refrigerant leakage detector for R22 or R407C cannot detect R410A

leakage.

Halide torch

NO

R22 or R407C leakage detector

NO

Items to be strictly observed :

Reasons:

Because R410A is a simulated azeotropic refrigerant, it can be handled in almost the same mammer as a single refrigerant

such as R22. Howerver, if the refrigerant is removed in the vapor phase, the composition of the refrigerant in the cylinder

will somewhat change.

Remove the refrigerant in the liquid phase. Additional refrigerant may be added in case of a refrigerant leak.

Characteristics of the Conventional and the New Refrigerants

Required accuracy of the vacuum gauge

Use a vacuum gauge that can measure up to 650Pa. Do not use a general gauge manifold since it cannot measure a

vacuum of 650Pa.

Vacuuming

Vacuum pump with check valve

A vacuum pump with a check valve is required to prevent the vacuum pump oil from flowing back into the refrigerant

circuit when the vacuum pump power is turned off (power failure). It is also possible to attach a check valve to the actual

vacuum pump afterwards.

Standard degree of vacuum for the vacuum pump

Use a pump which reaches 65Pa or below after 5 minutes of operation.

In addition, be sure to use a vacuum pump that has been properly maintained and oiled using the specified oil. If the

vacuum pump is not properly maintained, the degree of vacuum may be too low.

Evacuating time

Evacuate the equipment for 1 hour after 650Pa has been reached.

After envacuating, leave the equipment for 1 hour and make sure the that vacuum is not lost.

Operating procedure when the vacuum pump is stopped

In order to prevent a backflow of the vacuum pump oil, open the relief valve on the vacuum pump side or loosen the

charge hose to drawn in air before stopping operation.The same operating procedure should be used when using a

vacuum pump with a check valve.

1.

2.

3.

4.

5.

1.

2.

3.

1.

2.

R410A is a pseudo-azeotropic refrigerant (boiling point R32= -52 C, R125= -49 C) and can roughly be handled in the same

way as R22; however, be sure to fill the refrigerant from the liquid side, for doing so from the gas side will somewhat change

the composition of the refrigerant in the cylinder.

Charging Refrigerant

R410A must be in a liquid state when charging.

Reasons:

Note

In the case of a cylinder with a syphon, liquid R410A is charged without turning the cylinder up side down. Check the

type of cylinder before charging.

When refrigerant leaks, additional refrigerant may be charged. (Add the refrigerant from the liquid side)

Remedies to be taken in case of a refrigerant leak

10

Name of Parts

Air inlet

Compressor

(Inside of unit)

Air inlet

Air outlet

Compressor

(Inside of unit)

Air outlet

1U28HS1ERA 1U36HS1ERA 1U48LS1ERA 1U48LS1ERB

1U48IS1EAB 1U60IS1ERA 1U60IS1ERB 1U60IS1EAB

AU60NAIESA

1U48LS1EAB

Air inlet

Air outlet

(Inside of unit)

Compressor

11

Installation Procedure

Note :

(1) Fix the parts with screws.

(2) Don't intake the strong wind directly to

the outlet air-flow hole.

(3) A one meter distance should be

kept from the unit top.

(4) Don't block the surroundings of the unit with sundries.

(5) If the outdoor unit is installed in a place that is exposed

to the wind, install the unit so that the outlet grid is NOT

pointing in the direction of the wind.

(a) Concrete foundation (b) Foundation anchor

Concrete foundation

Unit

Anchor bolt

1. Selection of the place of installation

Select the place of installation satisfying the following conditions and, at the same time, obtain a consent from the client or

user.

Place where air circulates.

Place free from heat radiation from other heat sources.

Place where drain water may be discharged.

Place where noise and hot air may not disturb the neighborhood.

Place where there is not heavy snowfall in the winter time.

Place where obstacles do not exist near the air inlet and air outlet .

Place where the air outlet may not be exposed to a strong wind.

Place surrounded at four sides are not suitable for installation. A 1m or more of overhead space is needed for the unit.

Avoid mounting guide-louvers to the place where short-circuit is a possibility.

When installing several units, secure sufficient suction space to avoid short circuiting.

Open space requirement around the unit

Installation of Outdoor Unit

Wind direction

NO

L2

L3

L1

500

(Servicing

space)

Air outlet

Air inlet

Distance

open open

open

500 mm

150 mm150 mm 300 mm

300 mm 300 mm

L1

L2

L3

Case I Case II Case III

Fix the unit on the foundation in a proper way according to the condition of the installation place, referring to the following

information.

2. Installation of outdoor unit

Give enough room for the concrete foundation to fix by anchor bolts.

Place the concrete foundation deep enough.

Install the unit so that the angle of inclination must be less than 3 degrees.

Anchor bolt

Concrete foundation

Unit

To fix by bolts

Installation Procedure

12

Installation of Outdoor Unit

3. Installation dimension (Unit:mm)

580

1U28HS1ERA 1U36HS1ERA

1U48LS1ERA 1U48LS1ERB 1U48LS1EAB

1U48IS1EAB 1U60IS1ERA 1U60IS1ERB 1U60IS1EAB

AU60NAIESA

380

340

25

580

340

380

948

840

447

410

648

180

25

830

1008

25

1250

948

Installation Procedure

13

Piping Connection

2. Piping size

3. Limitations for one way piping length and vertical height difference

Precautions for refrigerant piping

Do not twist or crush piping.

Be sure that no dust is mixed in piping.

Bend piping with as wide angle as possible.

Keep insulating both gas and liquid piping.

Check flare-connected area for gas leakage.

Apply refrigerant oil to the joint and the flange.

To bend a pipe, give the roundness as possible not to crush

the pipe.

When connecting pipe, hold the pipe centre to centre and then

screw nut on by hand, refer to Fig.

Be careful not to let foreign matters, such as sands enter

the pipe.

4. Piping connection method

Forced fastening without centering may damage the threads and cause a gas leakage.

Model

One way piping length

Vertical height difference

(between indoor and outdoor)

Install the removed flare nuts to the pipes

to be connected, then flare the pipes.

Gas pipe

15.88x1.0mm

Liquid pipe

Gas pipe

9.52x0.8mm

19.05x1.0mm

Liquid pipe

9.52x0.8mm

90+0.5

1U48LS1ERA 1U48LS1ERB

1U48LS1EAB 1U48IS1EAB

1U60IS1ERA 1U60IS1ERB

1U60IS1EAB AU60NAIESA

1U28HS1ERA 1U36HS1ERA

Pipe diameter Fastening torque (N.m)

Liquid pipe 6.35mm

Gas pipe 15.88mm

Liquid pipe 9.52mm

Gas pipe 19.05mm

14.2-17.2

61.8-75.4

32.7-39.9

97.2-118.6

Gas pipe 12.7mm

49.5-60.3

1. Piping diagram

Outdoor

unit

Gas pipe

Liquid

pipe

Flare connection

Indoor

unit

3-way stop valve

less than 30 m less than 20 m

less than 50 m less than 30 m

1U28HS1ERA 1U36HS1ERA

1U48LS1ERA 1U48LS1ERB 1U48LS1EAB

1U48IS1EAB 1U60IS1ERA 1U60IS1ERB

1U60IS1EAB AU60NAIESA

1U28HS1ERA 1U36HS1ERA 1U48LS1ERA 1U48LS1ERB 1U48LS1EAB

1U48IS1EAB 1U60IS1ERA 1U60IS1ERB 1U60IS1EAB AU60NAIESA

Spanner

Nut

Joint

Installation Procedure

14

The air tightness test adopts nitrogen tank to give pressure according to the pipe connection mode as the following figure

shown.

The gas and liquid valve are all in close state. In order to prevent the nitrogen entering the circulation system of outdoor

unit, tighten the valve rod before giving pressure (both gas and liquid valve rods).

In 1) to 3) steps, if the pressure drops, check the leakage in each joint by listening, touching and using soap water etc.

to identify the leaking point. After confirming the leaking point, welding it again or tighten the nut tightly again.

Checking the leaking point

1) Pressurize for over 3 minutes at 0.3MPa (3.0 kg/cm

2

g).

2) Pressurize for over 3 minutes at 1.5MPa (15 kg/cm

2

g). A large

leakage will be found.

3) Pressurize for about 24 hours at 3.0MPa (30 kg/cm

2

g). A small

leakage will be found.

Installation Procedure

When the total length (L) of the two indoor units' connecting pipe is less than 5m, it is unnecessary to charge additional

refrigerant.

If the connecting pipe (L) exceeds 5m, it shall charge M(g) additional refrigerant per meter.

That is: Refrigerant charging amount = (L-5m) x 45 (g/m)

Air Tightness Test

When pressurizing for 24 hours, a variation of 1 C in the ambient temperature will cause a variation of 0.01MPa(0.1kg/cm

2

g)

in pressure. It shall be corrected during test.

Check if the pressure drops

If the pressure does not drop,

then pass.

If the pressure drops, then please check the leaking point.

Cylinder pressure gauge

Cylinder of nitrogern

Line pressure gauge

Tubing bring brazed

Sweat joint

Large slip-on connector

Service hose

Additional Refrigerant Charge

Outdoor

Completely tightened

Flare part

Outdoor units

Manhole

Discharging valve

stop valve totally closed

(Gas side)

Low pressure piezometer

High pressure piezometer

Meter separator

Dropping valve

stop valve totally closed

(Liquid side)

Nitrogen tank

VL VH

Indoor units

Indoor

Flare part

After finishing connection of refrigerant pipe, it shall perform air tightness test.

Only in COOLING operation can charge the additional refrigerant.

When charging, the refrigerant shall be charged from the charging nozzle of low pressure valve.

Be carefull when charging refrigerant, do not let the air mix into the system, and must charge the additional refrigerant

in liquid state.

Installation Procedure

15

Detach the service port's cap of gas stop valve, the valve rod's cap for liquid

stop valve and gas stop valve, and connect the service port into the projection

of charge hose (low) for gaugemanifold. Then connect the projection of

charge hose (center) for gaugemanifold into vacuum pump.

Open the handle at low in gaugemanifold, and operate vacuum pump. If the

scale-moves of gause (low) reach vacuum condition in a moment, check

the step 1 again.

Vacuumize for over 15min. And check the level gauge which should read -

0.1MPa (-76 cm Hg) at low pressure side. After the completion of vacuumizing,

close the handle 'Lo' in the vacuum pump. Check the condition of the scale

and hold it for 1-2min. If the scale-moves back in spite of tightening, make

flaring work again, then return to the beginning of the step 3.

Open the valve rod for the liquid stop valve to an angle of anticlockwise 90

degree. After 6 seconds, close the liquid stop valve and make the inspection

of gas leakge.

No gas leakage? In case of gas leakage, tighten parts of pipe connection. If leakage stops, then proceed the step 6. If it

does not stop gas leakage, discharge whole refrigerants from the service port. After flaring work again and vacuumize,

fill up prescribed refrigerant from the gas cylinder.

Detach the charge hose from the service port, open liquid stop valve and

gas stop valve. Turn the valve rod anticlockwise until hitting lightly.

To prevent the gas leakage, turn the service ports cap, the valve rodis cap

for liquid stop valve and gas stop valve a little more than the point where

the torque increases suddenly.

If the refrigerant of the air conditioner leaks, it is necessary to make all the refrigerant out. Vacuumize first, then charge

the liquid refrigerant into air conditioner according to the amount marked on the nameplate.

Vacuuming

Piping vavuum method: to use vacuum pump

1.

2.

3.

4.

5.

6.

7.

CAUTION:

90

Service port

90

for 6 sec.

Open

Liquid stop valve

Gas stop valve

Gauge manifold(R410A)

Vacuum pump(R410A)

Close

Valve rod cap

Service port cap

Liquid stop valve

Gas stop valve

Liquid stop valve

Gas stop valve

Installation Procedure

16

Electrical Wiring

Selection of size of power supply and interconnecting wires

Precautions for Electrical wiring

Electrical wiring work should be conducted only by authorized personnel.

Do not connect more than three wires to the terminal block. Always use round type crimped terminal lugs with insulated

grip on the ends of the wires.

Use copper conductor only.

Select wire sizes and circuit protection from table below. (This table shows 20 m length wires with less than 2% voltage

drop.)

DANGER OF BODILY INJURY OR DEATH

TURN OFF ELECTRIC POWER AT CIRCUIT BREAKER OR POWER SOURCE BEFORE MAKING ANY ELECTRIC

CONNECTIONS.

GROUND CONNECTIONS MUST BE COMPLETED BEFORE MAKING LINE VOLTAGE CONNECTIONS.

WARNING!

Item

Model

Phase

Switch breaker

(A)

Circuit breaker

Overcurrent protector

rated capacity (A)

Power source

wire size

(minimum)

(mm

2

)

Switch

breaker(A)

Earth leakage breaker

Leak

current(mA)

1U28HS1ERA

1U36HS1ERA

1U48LS1ERA

1U60IS1ERA

301 40 30 6.0 40

3 30 4.0 3020 30

1U48LS1ERB

1U60IS1ERB

AU60NAIESA

1U48LS1EAB

1U48IS1EAB

1U60IS1EAB

3 30 4.0 3020 30

If the supply cord is damaged, it must be replaced by the manufacturer or itsservice agent or a similar qualified person.

If the fuse of control box is broken, please change it with the type of T25A/450VAC;

If the fuse of control PC board is broken, please change it with the type of T3.15A/250VAC. But for 1U28HS1ERA,

1U36HS1ERA,1U48LS1ERA,,1U48LS1ERB,1U60IS1ERA,1U60IS1ERB, AU60NAIESA, the type is T6.3A/250VAC.

The wiring method should be in line with the local wiring standard.

The power cable and connecting cable should be self-provided.

All the cables shall have got the European authentication certificate. During installation, when the connecting cables

break off, it must be assured that the grouding wire is the last one to be broken off.

The breaker of the air conditioner should be all-pole switch; and the distance between its two contacts should not be no

less than 3mm. Such means for disconnection must be incorporation in the fixed wiring.

The distance between its two terminal blocks of indoor unit and outdoor unit should not be over 5m. If exceeded, the

diameter of the wire should be enlarged according to the local wiring standard.

A leakage breaker must be installed.

The specification of power cable

For models 1U28HS1ERA, 1U36HS1ERA,

1U48LS1ERA,1U60IS1ERA

the power cable should be H05RN-F 3G 6.0mm

2

.

For models 1U48LS1EAB,

1U48IS1EAB,

1U60IS1EAB, 1U48LS1ERB, 1U60IS1ERB, AU60NAIESA, the power cable

should be H07RN-F 5G 4.0mm

2

.

Installation Procedure

17

Installation Procedure

Electrical Wiring

Wiring procedure

1) Remove set screws on the side before taking off the front panel toward the direction.

2) Connect wires to the terminal block correctly and fix the wires with a wire clamp equipped nearby the terminal block.

3) Route the wires in a proper way and penetrate the wires through the opening for electrical wiring on the side panel.

WARNING:

INTERCONNECTING WIRES MUST BE WIRED ACCORDING TO FIGURE BELOW. INCORRECT WIRING MAY CAUSE

EQUIPMENT DAMAGE.

Test Run

CAUTION!

THIS UNIT WILL BE STARTED INSTANTLY WITHOUT "ON" OPERATION WHEN ELECTRIC POWER IS SUPPLIED.

BE SURE TO EXECUTE "OFF" OPERATION BEFORE ELECTRIC POWER IS DISCONNECTED FOR SERVICING.

This unit has a function of automatic restart system after recovering power stoppage.

1. Before starting test run (for all Heat pump models)

Confirm whether the power source breaker (main switch) of the unit has been turned on for over 12 hrs to energize the

crankcase heater in advance of operation.

2.Test run

Suction pressure at check joint of service valve for gas pipe.

Discharge pressure at check joint on the compressor discharge pipe.

Temperature difference between return air and supply air for indoor unit.

Run the unit continuously for about 30 minutes, and check the following.

Power supply :1PH,220-230V~,50Hz

Outdoor unit

terminal block

To indoor unit

Y/G

1 2 3L N

1U28HS1ERA 1U36HS1ERA 1U48LS1ERA 1U60IS1ERA

1U48LS1ERB 1U48LS1EAB 1U48IS1EAB 1U60IS1ERB 1U60IS1EAB AU60NAIESA

Outdoor unit

terminal block

Indoor unit

terminal block

Power supply:380-400V, 3N~,50Hz

Y/G

1 2 3

Y/G

1 2 3

R S T N

Troubleshooting

18

1U28HS1ERA/1U36HS1ERA/1U48LS1ERA/1U48LS1ERB/1U60IS1ERA/1U60IS1ERB/AU60NAIESA

La pagina sta caricando ...

Haier 1U60IS1ERA Guida d'installazione

Questo manuale è adatto anche per

Haier 1U60IS1ERA Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti