EPOX P2-100B Manuale utente

Marca: EPOX

Modello: P2-100B

Categoria: Schede madri

Tipo: Manuale utente

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without

notice.

Manual Revision 2.0

January 27, 1999

P2-100BP2-100B

P2-100B

A PentiumA Pentium

A Pentium

®®

II or Deschutes II or Deschutes

II or Deschutes

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

mainboard (100/66MHz)mainboard (100/66MHz)

mainboard (100/66MHz)

P2-100B

Technical Support Services

If you need additional information, help during installation or normal use of this

product, please contact your retailer. If your retailer can not help, you may E-Mail us

with any questions at the following address [email protected]

Record your serial number before installing your P2-100B mainboard. (the serial

number is located near the ISA slots at the edge of the board)

P2-100B serial number:

__________________________

BIOS Upgrades

Please use either our Web Site or BBS for current BIOS Upgrades.

Internet Access

http://www.epox.com

http://www.epox.com.tw

[email protected]

Modem Access

31-182-618451 (The Netherlands)

You can access this number via a Hayes-compatible modem with a 2,400 to

28,800 baud rate. The following setup format is required:

8 Data Bits, No Parity, 1 Stop Bit.

If your modem is unable to connect at higher baud rates, try connecting at

2,400 baud before contacting Technical Support.

Thank you for using EPoX mainboards!

P2-100B

User Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language

in any form by any means without the express written permission of EPoX Computer

Company (hereinafter referred to as EPoX) except documentation kept by the

purchaser for backup purposes.

EPoX provides this manual “as is” without warranty of any kind, either express or

implied, including but not limited to the implied warranties or conditions of merchant-

ability or fitness for a particular purpose. In no event shall EPoX be liable for any

loss or profits, loss of business, loss of use or data, interruption of business or for

indirect, special incidental, or consequential damages of any kind, even if EPoX has

been advised of the possibility of such damages arising from any defect or error in

the manual or product. EPoX may review this manual from time to time without

notice. For updated BIOS, drivers, or product release information you may visit

EPoX’s home page at: http://www.epox.com

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies.

The product name and revision number are both printed on the mainboard

itself.

Handling Procedures

Static electricity can severely damage your equipment. Handle the P2-100B

and any other device in your system with care and avoid unneccessary contact with

system components on the mainboard.

Always work on an antistatic surface to avoid possible damage to the motherboard

from static discharge.

We assume no responsibility for any damage to the P2-100B mainboard that results

from failure to follow installation instructions or failure to observe safety precautions.

CAUTION

The P2-100B mainboard is subject to

damage by static electricity. Always

observe the handling procedures.

P2-100B

Table of Contents

Section 1 Introduction

Components Checklist .................................... 1-1

Overview

Pentium II or Deschutes Processor.................. 1-2

S.E.C. Cartridge Terminology ......................... 1-3

Accelerated Graphics Port .............................. 1-4

Hardware Monitoring ..................................... 1-4

I/O Shield Connector...................................... 1-7

Power-On/Off (Remote) ................................. 1-6

System Block Diagram ................................... 1-7

Section 2 Features

P2-100B Features .......................................... 2-1

Section 3 Installation

P2-100B Detailed Layout ............................... 3-2

Easy Installation Procedure

Configure Jumpers .......................................... 3-3

System Memory Configuration ........................ 3-5

Installing a Pentium

II Processor .................... 3-7

Device Connectors ......................................... 3-8

Section 4 Award BIOS Setup

BIOS Instructions ........................................... 4-1

Standard CMOS Setup .................................. 4-2

BIOS Features Setup ..................................... 4-3

Chipset Features Setup ................................... 4-8

Power Management Setup .............................. 4-10

PNP/PCI Configuration .................................. 4-13

Load Setup Defaults ....................................... 4-14

P2-100B

Integrated Peripherals ..................................... 4-15

Change Supervisor or User Password ............. 4-19

IDE HDD Auto Detection............................... 4-20

HDD Low Level Format................................. 4-22

Save & Exit Setup .......................................... 4-22

Exit Without Saving......................................... 4-22

Appendix

Appendix A

Memory Map ................................................. A-1

I/O Map......................................................... A-1

Timer & DMA Channels Map......................... A-2

Interrupt Map ................................................. A-2

RTC & CMOS RAM Map ............................ A-3

Appendix B

POST Codes ................................................. A-5

Unexpected Errors ......................................... A-8

Appendix C

Load Setup Defaults ....................................... A-9

Appendix D

CPU Clock Frequency Selection In BIOS Setting

...................................................................... A-10

IntroductionP2-100B

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) P2-100B mainboard

üü

ü B. (1) P2-100B user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) Hard drive ribbon cable

E. (1) PS/2 Mouse Connector

üü

ü F. (1) Bus master drivers

üü

ü G. (1) COM Port/LPT Port Connector

USERS

MANUAL

P2-100B

Introduction P2-100B

Page 1-2

Overview

Pentium II

The Pentium

II Processor is the follow-on to the Pentium

Processor. The

Pentium

II Processor, like the Pentium

Pro processor, implements a Dynamic

Execution micro-architecture -- a unique combination of multiple branch prediction,

data flow analysis, and speculative execution. This enables the Pentium

II Proces-

sor to deliver higher performance than the Pentium

processor, while maintaining

binary compatibility with all previous Intel architecture processors.

A significant feature of the Pentium

II Processor, from a system perspective, is the

built-in direct multiprocessing support. In order to achieve multiprocessing, and

maintain the memory and I/O bandwidth to support it, new system designs are

needed. For systems with dual processors, it is important to consider the additional

power burdens and signal integrity issues of supporting multiple loads on a high speed

bus. The Pentium

II Processor card supports both uni-processor and dual processor

implementations.

The Pentium

II Processor utilizes Single Edge Contact (S.E.C.) (Figure 1) cartridge

packaging technology. The S.E.C. cartridge allows the L2 cache to remain tightly

coupled to the processor, while maintaining flexibility when implementing high perfor-

mance processors into OEM systems. The second level cache is performance

optimized and tested at the cartridge level. The S.E.C. cartridge utilizes surface

mounted core components and a printed circuit board with an edge finger

connection. The S.E.C. cartridge package introduced on the Pentium

II Processor

will also be used in future Slot 1 processors.

The S.E.C. cartridge has the following features: a thermal plate, a cover and a PCB

with an edge finger connection. The thermal plate allows standardized heatsink

attachment or customized thermal solutions. The thermal plate enables a reusable

heatsink to minimize fit issues for serviceability, upgradeability and replacement. The

full enclosure also protects the surface mount components. The edge finger connec-

tion maintains socketabilty for system configuration. The edge finger connector is

denoted as ‘Slot 1 connector’ in this and other documentation.

The entire enclosed product is called the Pentium

II Processor. The packaging

technology and each of the physical elements of the product are referred to using

accurate technical descriptions. This allows clear reference to the products as just a

IntroductionP2-100B

Page 1-3

processor. This is the model used in past packaging technologies like PGA, TCP,

PQFP, DIP, etc.

S.E.C. Cartridge Terminology

• Pentium

II Processor

The new enclosed card packaging technology is called a “Single

Edge Contact cartridge.” This is similar to previous names for

packaging technology such as PGA or TCP.

• Processor card

The green PCB (with or without components on it)

• Processor core

The silicon on the PLGA package on the PCB

• Cover

The plastic cover on the opposite side from the thermal plate.

• Slot 1

The slot that the S.E.C. cartridge plugs into, just as the Pentium

Pro processor uses Socket 8.

• Retention mechanism

Formerly ‘retention module’ the dual posts, etc. that holds the

cartridge in place.

• Thermal plate

The heatsink attachment plate.

• Heat sink supports

The support pieces that are mounted on the mainboard to provide

added support for heatsinks.

Figure 1: Pentium

II Processor

CPU with S.E.C. Cartridge

Processor

Printed Circuit Board

Thermal Plate

Cover

The L2 cache (TagRAM, PBSRAM)

components keep standard industry

names.

The Pentium

II Processor is the first

product to utilize the S.E.C. cartridge

technology and Slot 1 connector. Unless

otherwise noted, any references to

“Pentium

II Processor,” “Pentium

Processor/Slot 1 processor” or Proces-

sor” will apply to both the Pentium

Processor desktop processors.

Introduction P2-100B

Page 1-4

Accelerated Graphics Port

(AGP or A.G.P.)

Typically, 3D graphics rendering requires a tremendous amount of memory, and

demands ever increasing throughput speed as well. As 3D products for the personal

computer become more and more popular, these demands will only increase. This

will cause a rise in costs for both end users and manufacturers. Lowering these

costs as well as improving performance is the primary motivation behind AGP. By

providing a massive increase in the bandwidth available between the video card and

the processor, it will assist in relieving some of these pressures for quite sometime.

Hardware Monitoring

Hardware monitoring allows you to monitor various aspects of your systems opera-

tions and status. The features include CPU temperature, voltage and RPM of fan.

Desktop Management Interface

(DMI)

DMI, or Desktop Management Interface, is a BIOS level method for monitoring

specific BIOS related hardware features. It allows the BIOS to collect and store

information specific to the system, so that vendors and system integrators will have

greater access to information regarding system configuration and design. This allows

for better troubleshooting, migration planning, and upgradeability decision making.

IntroductionP2-100B

Page 1-5

Page Right Blank

Introduction P2-100B

Page 1-6

ATX

POWER SUPPLY

P2-100B Board

Power-On/Off (Remote)

The P2-100B has a single 20-pin connector for ATX power supplies. For ATX

power supplies that support the Remote On/Off feature, this should be connected to

the systems front panel for system Power On/Off button. The systems power On/

Off button should be a momentary button that is normally open.

The P2-100B has been designed with “Soft Off" functions. You can turn Off the

system from one of two sources: The first is the front panel Power On/Off button,

and the other is the "Soft Off" function (coming from the P2-100B’s onboard circuit

controller) that can be controlled by the operating system. Windows 95 will control

this when the user clicks that they are ready to Shutdown the system.

Figure 4: Simple ATX Power ON/OFF Controller

J 3

Case (chassis) Power

ON/OFF button (J 3)

IntroductionP2-100B

Page 1-7

Figure 5: System Block Diagram

System Block Diagram

Pentium II or

Deschutes

Processor

PAC

PCI Bridge

and memory

controller

VT82C691

VT82C586B

I/O Bridge

100/66MHz

66MHz

Winbond

83877TF

Introduction P2-100B

Page 1-8

Page Left Blank

FeaturesP2-100B

Page 2-1

Section 2

FEATURES

P2-100B Features:

• P2-100B is based on the Pentium

II Processor operating at 200 ~ 450 MHz

on Slot 1. The board is configured by an DIP Switch to match your CPU

clock speed.

• Designed with VIA Apollo PRO AGPset.

• Supports up to 256MB of DRAM (minimum of 8 MB) on board (please see

Section 3-2).

• Supports (2) 16 bit ISA slots, (3) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The P2-100B supports (3) PCI

Bus Master slots and a jumperless PCI INT# control scheme which reduces

configuration confusion when plugging in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE

interfaces.

• Designed with Winbond W83877TF Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.epox.com/

please visit our Technical Support section for the latest updates)

• P2-100B utilizes a Lithium battery which provides environmental protection

and longer battery life.

• Supports the Universal Serial Bus (USB) Header. The onboard VT82C586B

chip provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

• Built-in ATX 20-pin and AT 12-Pin power supply connector.

• Software power-down when using Windows

95.

Features P2-100B

Page 2-2

• Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely.

• Resume by Alarm - Allows your system to turn on at a preselected time.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Built-in WOL (Wake-up On Lan) Connector.

InstallationP2-100B

Page 3-1

Section 3

INSTALLATION

Installation P2-100B

Page 3-2

Figure 6

P2-100B Detailed Layout

AGP SLOT

PCI Slot #1

PCI Slot #2

PCI Slot #3

ISA Slot #1

ISA Slot #2

VIA

82C691

CPU Cartridge SLOT 1

CPU FAN

Flash Memory

for BIOS

DIMM 1

DIMM 2

Bank 1

Bank 0

JP5

WOL

Battery

IDE2IDE1 FDD1

POWER_ON

RESET

SPK

KEYLOCK

IR CONN.

JP1

JP6

USB CONN.

InstallationP2-100B

Page 3-3

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. Configure DIP Switch and Jumper to match your hardware

3-2. Install memory chips

3-3. Install Pentium II Processor

3-4. Device Connectors

Section 3-1

Configure DIP Switch

We design this mainboard with a DIP Switch to make your install fast and easy.

The following will describe all of the DIP Switch that you are required to set before

moving on to step 3-2.

Note: The DIP Switch as depicted as shown (Figure 6) in their correct physi-

cal orientation.

JP6 CPU BUS CLOCK

JP6 = 1-2 - Auto

= 2-3 - 100MHz

JP1 = 1-2 - Normal (Default)

= 2-3 - Clear CMOS (momentarily)

JP1 CMOS Clear

SW 1 CPU

66MHz

100MHz

200

233

266

300

350

400

300

333

366

450

500

550

400 600

* :Reserved

Installation P2-100B

Page 3-4

Section 3-2

System Memory Configuration

Memory Layout

The P2-100B supports (3) 168-pin DIMMs (Dual In-line Memory Module). The

DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM). The DIMMs may be installed using just one chip.

• We recommend using SDRAM DIMM can not mixing

with EDO DIMM modules together.

• We recommend when installed the 100MHz Processor using DIMM

SDRAM must be 125MHz (-8ns) bus speed. If used 100MHz (-10ns)

SDRAM may be critical timing for the motherboard.

• About the “PC/100 SDRAM spec.” information you may visit Intel’s

home page at:

http//developer.intel.com/design/pcisets/memory/index.htm

• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or

125MHz (-8ns) bus speed.

Figure 2 and Table 1 show several possible memory configurations using

DIMM 1 (M1)

DIMM 2 (M2)

Bank 0

Bank 1

Synchronous

SDRAM or EDO

DIMM

Figure 2

JP5 DIMM CLOCK SELECT

JP5 = 1-2 - DIMM=CPU

= 2-3 - DIMM=AGP

La pagina sta caricando ...

EPOX P2-100B Manuale utente

Marca: EPOX

Modello: P2-100B

Categoria: Schede madri

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: EPOX P2-100B User manual

EPOX P2-100B Manuale utente

EPOX P2-100B Manuale utente

in altre lingue

Documenti correlati

Altri documenti