EPOX EP-61BXC-A Manuale utente

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without

notice.

Manual Revision 2.1

August 27, 1998

EP-61BXEP-61BX

EP-61BX

C-AC-A

C-A

A PentiumA Pentium

A Pentium

®®

®

II or Deschutes II or Deschutes

II or Deschutes

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

mainboard (100/66MHz)mainboard (100/66MHz)

mainboard (100/66MHz)

EP-61BXC-A

Technical Support Services

If you need additional information, help during installation or normal use of this

product, please contact your retailer. If your retailer can not help, you may E-Mail us

with any questions at the following address [email protected]

Record your serial number before installing your EP-61BXC-A mainboard. (the serial

number is located near the ISA slots at the edge of the board)

EPoX EP-61BXC-A serial number:

__________________________

BIOS Upgrades

Please use either our Web Site or BBS for current BIOS Upgrades.

Internet Access

http://www.epox.com

[email protected]

Modem Access

31-182-618451 (The Netherlands)

You can access this number via a Hayes-compatible modem with a 2,400 to

28,800 baud rate. The following setup format is required:

8 Data Bits, No Parity, 1 Stop Bit.

If your modem is unable to connect at higher baud rates, try connecting at

2,400 baud before contacting Technical Support.

Thank you for using EPoX mainboards!

EP-61BXC-A

User Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language

in any form by any means without the express written permission of EPoX Computer

Company (hereinafter referred to as EPoX) except documentation kept by the

purchaser for backup purposes.

EPoX provides this manual “as is” without warranty of any kind, either express or

implied, including but not limited to the implied warranties or conditions of merchant-

ability or fitness for a particular purpose. In no event shall EPoX be liable for any

loss or profits, loss of business, loss of use or data, interruption of business or for

indirect, special incidental, or consequential damages of any kind, even if EPoX has

been advised of the possibility of such damages arising from any defect or error in

the manual or product. EPoX may review this manual from time to time without

notice. For updated BIOS, drivers, or product release information you may visit

EPoX’s home page at: http://www.epox.com

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies.

The product name and revision number are both printed on the mainboard

itself.

Handling Procedures

Static electricity can severely damage your equipment. Handle the EP-

61BXC-A and any other device in your system with care and avoid unneccessary

contact with system components on the mainboard.

Always work on an antistatic surface to avoid possible damage to the motherboard

from static discharge.

We assume no responsibility for any damage to the EP-61BXC-A mainboard that

results from failure to follow installation instructions or failure to observe safety

precautions.

CAUTION

The EP-61BXC-A mainboard is subject to

damage by static electricity. Always

observe the handling procedures.

EP-61BXC-A

Table of Contents

Section 1 Introduction

Components Checklist .................................... 1-1

Overview

Pentium II or Deschutes Processor.................. 1-2

S.E.C. Cartridge Terminology ......................... 1-3

Accelerated Graphics Port .............................. 1-4

Hardware Monitoring ..................................... 1-4

Desktop Management Interface ...................... 1-4

EP-61BXC-A Form-Factor ........................... 1-6

I/O Shield Connector...................................... 1-7

Power-On/Off (Remote) ................................. 1-7

System Block Diagram ................................... 1-8

Section 2 Features

EP-61BXC-A Features .................................. 2-1

Section 3 Installation

EP-61BXC-A Detailed Layout ....................... 3-2

Easy Installation Procedure

Configure Jumpers .......................................... 3-3

System Memory Configuration ........................ 3-5

Installing a Pentium

®

II Processor .................... 3-9

Device Connectors ......................................... 3-10

External Modem Ring-in Power ON and

Keyboard Power ON Function (KBPO) ........ 3-12

Section 4 Award BIOS Setup

BIOS Instructions ........................................... 4-1

Standard CMOS Setup .................................. 4-2

BIOS Features Setup ..................................... 4-3

EP-61BXC-A

Chipset Features Setup ................................... 4-8

Power Management Setup .............................. 4-12

PNP/PCI Configuration .................................. 4-16

Load Setup Defaults ....................................... 4-18

Integrated Peripherals ..................................... 4-18

Change Supervisor or User Password ............. 4-23

IDE HDD Auto Detection............................... 4-24

HDD Low Level Format................................. 4-26

Save & Exit Setup .......................................... 4-26

Exit Without Saving......................................... 4-26

Section 5 PCI Sound

Driver Installation............................................ 5-1

Section 6 Appendix

Appendix A

Memory Map ................................................. A-1

I/O Map......................................................... A-1

Timer & DMA Channels Map......................... A-2

Interrupt Map ................................................. A-2

RTC & CMOS RAM Map ............................ A-3

Appendix B

POST Codes ................................................. A-5

Unexpected Errors ......................................... A-8

Appendix C

Load Setup Defaults ....................................... A-9

Appendix D

CPU Clock Frequency Selection In BIOS

Setting ............................................................ A-10

IntroductionEP-61BXC-A

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) EP-61BXC-A mainboard

üü

ü B. (1) EP-61BXC-A user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) Hard drive ribbon cables

üü

ü E. (1) Foldable Retention Module

F. (1) Heatsink Support Unit (Optional)

G. (1) PS/2 to AT keyboard connector adapter (optional)

üü

ü H. (1) Bus master drivers

(1) USDM

USERS

MANUAL

EP-61BXC-A

B

A

G

C

D

F

Top Half

Bottom Half

E

H

or

Introduction EP-61BXC-A

Page 1-2

Overview

Pentium II or Deschutes Processor

The Pentium

®

II or Deschutes Processor (The Deschutes Processor as 300/

100MHz, 350/100MHz, 400/100MHz and 450/100MHz speed with 512K-L2 cache

Versions.) is the follow-on to the Pentium

®

Processor. The Pentium

®

II or

Deschutes Processor, like the Pentium

®

Pro processor, implements a Dynamic

Execution micro-architecture -- a unique combination of multiple branch prediction,

data flow analysis, and speculative execution. This enables the Pentium

®

II Proces-

sor to deliver higher performance than the Pentium

®

processor, while maintaining

binary compatibility with all previous Intel architecture processors.

A significant feature of the Pentium

®

II or Deschutes Processor, from a system

perspective, is the built-in direct multiprocessing support. In order to achieve

multiprocessing, and maintain the memory and I/O bandwidth to support it, new

system designs are needed. For systems with dual processors, it is important to

consider the additional power burdens and signal integrity issues of supporting

multiple loads on a high speed bus. The Pentium

®

II or Deschutes Processor card

supports both uni-processor and dual processor implementations.

The Pentium

®

II or Deschutes Processor utilizes Single Edge Contact (S.E.C.)

(Figure 1) cartridge packaging technology. The S.E.C. cartridge allows the L2 cache

to remain tightly coupled to the processor, while maintaining flexibility when imple-

menting high performance processors into OEM systems. The second level cache is

performance optimized and tested at the cartridge level. The S.E.C. cartridge utilizes

surface mounted core components and a printed circuit board with an edge finger

connection. The S.E.C. cartridge package introduced on the Pentium

®

II Processor

will also be used in future Slot 1 processors.

The S.E.C. cartridge has the following features: a thermal plate, a cover and a PCB

with an edge finger connection. The thermal plate allows standardized heatsink

attachment or customized thermal solutions. The thermal plate enables a reusable

heatsink to minimize fit issues for serviceability, upgradeability and replacement. The

full enclosure also protects the surface mount components. The edge finger connec-

tion maintains socketabilty for system configuration. The edge finger connector is

denoted as ‘Slot 1 connector’ in this and other documentation.

The entire enclosed product is called the Pentium

®

II or Deschutes Processor. The

IntroductionEP-61BXC-A

Page 1-3

packaging technology and each of the physical elements of the product are referred

to using accurate technical descriptions. This allows clear reference to the products

as just a processor. This is the model used in past packaging technologies like PGA,

TCP, PQFP, DIP, etc.

S.E.C. Cartridge Terminology

• Pentium

®

II or Deschutes Processor

The new enclosed card packaging technology is called a “Single Edge

Contact cartridge.” This is similar to previous names for packaging

technology such as PGA or TCP.

• Processor card

The green PCB (with or without components on it)

• Processor core

The silicon on the PLGA package on the PCB

• Cover

The plastic cover on the opposite side from the thermal plate.

• Slot 1

The slot that the S.E.C. cartridge plugs into, just as the Pentium

®

Pro

processor uses Socket 8.

• Retention mechanism

Formerly ‘retention module’ the dual posts, etc. that holds the cartridge

in place.

• Thermal plate

The heatsink attachment plate.

• Heat sink supports

Figure 1: Pentium

®

II or Deschutes

Processor CPU with S.E.C. Cartridge

Processor

Printed Circuit Board

Thermal Plate

Cover

The support pieces that are

mounted on the mainboard

to provide added support for

heatsinks.

The L2 cache (TagRAM, PBSRAM)

components keep standard industry

names.

The Pentium

®

II or Deschutes Processor

is the first product to utilize the S.E.C.

cartridge technology and Slot 1

connector. Unless otherwise noted, any

references to “Pentium

®

II Processor,”

Introduction EP-61BXC-A

Page 1-4

“Pentium

®

II or Deschutes Processor/Slot 1 processor” or “Deschutes Processor”

will apply to both the Pentium

®

II Processor desktop processors.

Accelerated Graphics Port

(AGP or A.G.P.)

Typically, 3D graphics rendering requires a tremendous amount of memory, and

demands ever increasing throughput speed as well. As 3D products for the personal

computer become more and more popular, these demands will only increase. This

will cause a rise in costs for both end users and manufacturers. Lowering these

costs as well as improving performance is the primary motivation behind AGP. By

providing a massive increase in the bandwidth available between the video card and

the processor, it will assist in relieving some of these pressures for quite sometime.

Hardware Monitoring

Hardware monitoring allows you to monitor various aspects of your systems opera-

tions and status. The features include CPU temperature, voltage and RPM of fan.

IntroductionEP-61BXC-A

Page 1-5

Page Right Blank

Introduction EP-61BXC-A

Page 1-6

EP-61BXC-A Form-Factor

The EP-61BXC-A is designed with MicroATX form factor - the new industry

standard of chassis. The MicroATX form factor is essentially a Baby-AT baseboard

rotated 90 degrees within the chassis enclosure and a new mounting configuration for

the power supply. With these changes the processor is relocated away from the

expansion slots, allowing them all to hold full length add-in cards. MicroATX defines

a double height aperture to the rear of the chassis which can be used to host a wide

range of onboard I/O. Only the size and position of this aperture is defined, allowing

PC manufacturers to add new I/O features (e.g.; TV input, TV output, joystick,

modem, LAN, etc.) to systems. This will help systems integrators differentiate their

products in the marketplace, and better meet your needs.

• Smaller size promotes a smaller system size.

• I/O shield does not need to be retooled in an ATX 2.01 or later. Mainboard could

be used in an ATX 2.01-compliant.

• A smaller power supply cam be used. High integration on mainboard reduces the

system costs.

Full length

slots

Expandable I/O

5 1/4"

Bay

3 1/2"

Bay

Figure 2: Summary of MicroATX/ATX chassis features

CPU located near

Power Supply

Single chassis

fan for

system

Micro

ATX/

ATX

Power

Supply

MicroATX/ATX

power connector

Floppy / IDE

connectors

close to

peripheral

bays

IntroductionEP-61BXC-A

Page 1-7

I/O Shield Connector

The EP-61BXC-A is equipped with an I/O back panel. Please use the appropriate

I/O shield (figure 3).

MicroATX

POWER SUPPLY

EP-61BXC-A Board

Power-On/Off (Remote)

The EP-61BXC-A has a single 20-pin connector for MicroATX power supplies. For

MicroATX/ATX power supplies that support the Remote On/Off feature, this should

be connected to the systems front panel for system Power On/Off button. The

systems power On/Off button should be a momentary button that is normally open.

The EP-61BXC-A has been designed with “Soft Off" functions. You can turn Off

the system from one of two sources: The first is the front panel Power On/Off the

button, and the other is the "Soft Off" function (coming from the EP-61BXA-M’s

onboard circuit controller) that can be controlled by the operating system. Windows

95/98 will control this when the user clicks that they are ready to Shutdown the

system.

Case (chassis) Power

ON/OFF button

Figure 4: Simple MicroATX/ATX Power

ON/OFF Controller

J3

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Figure 3: I/O back panel layout

Joystick/Midi port

Introduction EP-61BXC-A

Page 1-8

Figure 5: System Block Diagram

System Block Diagram

Pentium II or

Deschutes

Processor

PAC

PCI Bridge

and memory

controller

443BX

PllX4E

I/O Bridge

100/66MHz

66MHz

PCI

Soun d

AC

97

FeaturesEP-61BXC-A

Page 2-1

Section 2

FEATURES

EP-61BXC-A Features:

• EP-61BXC-A is based on the Pentium

®

II or Deschutes Processor operating

at 233 ~ 333MHz (66MHz) or 300 ~ 450MHz (100MHz) on Slot 1. The board

is configured by an Easy-Setting-Daul-Jumper (E.S.D.J.) to match your CPU

clock speed.

• Designed with Intel’s 82443 BX AGPset.

• Supports up to 768 Mega of DRAM (minimum of 16 MB) on board, You can

use 168-pin DIMM x 3. It will automatically detect Extended Data Output

(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at

66MHz or 100MHz (please see Section 3-2).

• EP-61BXC-A will support Error Checking and Correcting (ECC) when using

paritys DRAM memory modules. This will detect multiple bit errors and

correct 1-bit memory errors.

• Supports (1) 16 bit ISA slots, (3) 32 bit PCI slots, (1) AGP slot and provides

(2) independent high performance PCI IDE interfaces capable of supporting

PIO Mode 3/4 and Ultra DMA 33 devices. The EP-61BXC-A supports (3)

PCI Bus Master slots and a jumperless PCI INT# control scheme which

reduces configuration confusion when plugging in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with Winbond W83977TF/EF Multi I/O: (1) floppy port, (1) parallel

port (EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

• Includes a PS/2 mouse connector.

• Allows use of a PS/2 keyboard.

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.epox.com

please visit our Technical Support section for the latest updates)

Features EP-61BXC-A

Page 2-2

• EP-61BXC-A utilizes a Lithium battery which provides environmental protec

tion and longer battery life.

• Supports the Universal Serial Bus (USB) connector. The onboard PIIX4E chip

provides the means for connecting PC peripherals such as; keyboards,

joysticks, telephones, and modems.

• Built-in ATX 20-pin power supply connector.

• Software power-down when using Windows

®

95.

• Supports ring-in feature (remote power-on through external modem,

allow system to be turned on remotely.

• Resume by Alarm - Allow your system to turn on at a preselected time.

• Power Loss Recovery - In the event of a power outtage your system will

automatically turn itself back on without user intervention.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Desktop Management Interface (DMI) facilitating the management

of desktop computers, hardware and software components and peripherals,

whether they are stand-alone systems or linked into networks. (optional)

• Supports Hot key, Any key or password Keyboard power ON function

(KBPO).

• Supports USDM software to offer motherboard various status on Windows

®

95/98, or Windows

®

NT 4.0/5.0.

• Supports the CPU, PWR and Chassis fan Auto stop in the sleep mode.

• Supports the System Power LED (PANEL) blinks in the sleep mode.

• Built-in WOL (Wake On Lan) Connector.

• Built-in YAMAHA YMF724 PCI Sound Onboard.

• Ture Full Duplex playback and Capture with different Sampling Rate.

• Maximum 64-voice XG captital Wave table

• Synthesizer including GM Compatibility.

• Supports OPL3, Sound Blaster Pro, MPU401 UART mode and Joystick

function.

InstallationEP-61BXC-A

Page 3-1

Section 3

INSTALLATION

Installation EP-61BXC-A

Page 3-2

Figure 6

EP-61BXC-A Detailed Layout

InstallationEP-61BXC-A

Page 3-3

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. Configure Jumpers to match your hardware

3-2. Install memory chips

3-3. Install Pentium II or Deschutes Processor

3-4. Device Connectors

Section 3-1

Configure Jumpers

EPoX designs all motherboards with the fewest jumpers to make your installation

fast and easy.

The following will describe all of the jumpers that you are required to set before

moving on to step 3-2.

Note: The jumpers as depicted as shown (Figure 6) in their correct physical

orientation.

JP13 Keyboard Power-ON function (refer to the section 3-5)

JP13 = 1-2 - Enabled

= 2-3 - Disabled(Default)

1

3

J7 WOL (Wake On Lan) Connector

Reserved for NIC (Network Interface Card) to

Wake the System.

JP1 = 1-2 - Run Mode (Default)

= 2-3 - Clear CMOS (momentarily)

JP1 CMOS Clear

1

3

JP7 = 1-2 - Enabled PCI Sound (Default)

= 2-3 - Disabled PCI Sound

JP7 PCI Sound (Onboard Sound Chip)

1

3

Installation EP-61BXC-A

Page 3-4

Note: Based on the implementation of Intel 440BX PCIset, EP-61BXC-A is

able to provide two host bus frequencies -- either 66 or 100MHz for Slot1

processor and memory operating. The default is set at 100MHz once

Pentium

®

II processor to be mounted onto this mainboard. However, no

matter what kind of Slot1 processor you installed, it should come with right

memory modules for normal and stable operation. For example, if you install

a Deschutes processor, you should use the SDRAM module with 100MHz

based(or above) to match the CPU speed. Furthermore, one thing you may

need to bear in mind, before the CPU installation, it is anyway our advice to

use JP3 and set up right speed of Slot1 processor at any time. You may feel

like to know about AGP interface, which always runs under 66MHz no matter

what frequency of processor you installed.

*

***

**

La pagina sta caricando ...

EPOX EP-61BXC-A Manuale utente

EPOX EP-61BXC-A Manuale utente

in altre lingue

Documenti correlati

Altri documenti