Information for users in the UK
(Not applicable outside the UK)
Positioning the TV
For the best results, choose a position where light does not fall directly on the screen, and at some distance away from radiators
or other sources of heat. Leave a space of at least 5 cm all around the TV for ventilation, making sure that curtains, cupboards etc.
cannot obstruct the air flow through the ventilation apertures.
The TV is intended for use in a domestic environment only and should never be operated or stored in excessively hot or humid
atmospheres.
General Points
Please take note of the section 'Tips' at the end of the English section in this booklet.
Interference
The Department of Trade and Industry operates a Radio Interference Investigation Service to help TV license holders improve
reception of BBC and IBA programmes where they are being spoilt by interference.
If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television and Radio Reception".
Mains connection
Before connecting the TV to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate
on the rear panel of the TV. If the mains voltage is different, consult your dealer.
Important
This apparatus is fitted with an approved moulded 13 Amp plug.
To change a fuse in this type of plug proceed as follows :
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS1362 5A,A.S.T.A. or BSI approved type.
In order to maintain conformity to the EMC directive, the mains plug on this product must not be removed.
Connecting the aerial
The aerial should be connected to the socket marked x at the back of the set. An inferior aerial is likely to result in a poor,
perhaps unstable picture with ghost images and lack of contrast. Make-shift loft or set-top aerials are often inadequate.
Your dealer will know from experience the most suitable type for your locality.
Should you wish to use the set in conjunction with other equipment, which connects to the aerial socket such as TV games, or a
video camera, it is recommended that these be connected via a combiner unit to avoid repeated connection and disconnection of
the aerial plug.
Loop aerial (if provided)
The loop aerial packed with the set will give satisfactory reception under good signal conditions. Fit the aerial bracket and lead by
pushing the peg into the square hole in the backcover until it latches in place. Then insert the plug on the lead into the aerial
socket.
4979.1 gb 06-01-2000 17:05 Page 1
Contents
1
English
Your remote control 2
Preparation 3
Installation 4
Store TV channels 4
Select the menu language and country 4
Automatic installation 5
Manual installation 5
Give name 6
Reshuffle the programme list 6
Select favourite TV channels 6
Install TV setup 7-8
EasyLink features are based on the “one touch operation” approach.This
means that a sequence of actions are executed at the same time in both
the television and the video cassette recorder, provided both are fitted
with the EasyLink function and connected with the eurocable
supplied with your video recorder.
Installation
Operation
Use of the remote control 9-11
Use of the menus
Picture menu 12
Sound menu 12
Features menu 13
NEXTVIEW 14-18
Teletext 19-21
The keys in front of the TV 21
Connect peripheral equipment
Connecting and selecting equipment 22-25
Remote control functions for peripherals 25-26
Recording 27
Tips 28
Index 28
Glossary 29
4979.1 gb 06-01-2000 17:05 Page 1
2 Preparation
M h a
SMART
ACTIVE
CONTROLSMART
213
546
879
0
B
w
®
Ò
‡π
†
æ b
Ï
i
Mqa
SQ
TV
MOVIE SPORT CHILD NEWS OTHER
VCR DVD SAT
TUNER CD
OK
MENU
TAPE CDR
SMARTSMART
PICTURESOUND
¬V P
0
◊
U
XP
fh
Uf
yÚ
o
œ
pπ
yÚ
®q
b ficd
INSTANT
ZOOM
Preparation
Your remote control
Teletext p. 20
U time display/subpage selection
f solution to puzzles
display PDC/VPS code
h enlarge
P no function
Smart Controls
M smart sound p. 11
h active control p. 10
a smart picture p. 11
Dual screen p. 10
b dual screen on
c no function
d still teletext picture
fi strobe
B switch to standby p. 9
i on screen info p. 9
0 previous programme p. 9
◊ video recorder/DVD function p. 9
X bilingual choice/sound info p.11
TXT language group selection p. 19
EasyLink p. 11
®
INSTANT recording
q picture format p. 11
b teletext on/off p. 19
Ï main menu on/off p. 9
cursor to select
your choice p. 12
Installation p. 4
V volume up/down p. 9
¬ sound mute p. 9
P programme selection p. 9
Peripherals p. 25
w selection of EXT1, EXT2, EXT3
or FRONT
TV, video recorder (VCR), DVD,
Satellite (SAT), TUNER, CD, TAPE or
cd-recordable (CDR) selection.
Colour keys
- select TV channels by theme p. 11
- direct teletext page or
subject selection p. 20
Audio- and Video equipment p. 25-26
O no function
S freeze the picture p. 9
hold teletext page p. 20
Q incredible surround p. 9
æ
NEXTVIEW on/off p. 9
OK activate your choice
4979.1 gb 06-01-2000 17:05 Page 2
& Place the TV on a solid surface.
For ventilation, leave at least 5 cm free all around the TV.
Do not place the TV on a carpet.
To prevent any unsafe situations, do not place any objects on top of the TV.
Avoid heat, direct sunlight and exposure to rain or water.
Remove, if present, the blue protection foil at both front sides of the TV.
é Insert the aerial plug firmly into the aerial socket x at the back of the
TV. For best picture quality use the suppressor-aerial cable supplied.
“ Insert the mains plug in the wall socket having a mains voltage of 220V-240V.
To prevent damaging the mains (AC) cord which could cause a fire or electric
shock, do not place the TV on the cord.
‘ Remote control: Remove the cover of the battery compartment.
Insert the 2 batteries supplied (Type R6-1.5V).
Press the TV key to be sure your remote control is in the TV mode.
The batteries supplied do not contain the heavy metals mercury and cadmium.
Nevertheless in many countries exhausted batteries may not be disposed of with
your household waste. Please check on how to dispose of exhausted batteries
according to local regulations.
Note: this remote control functions with TVs which use the RC6 signalling standard.
( Switch the TV on : Press the power switch A on the front of your TV.
A green indicator on the front of the TV lights up and the screen comes on.
If the indicator is red, press the
-
P+ key on the remote control.
The green lamp blinks every time you press a key on the remote control.
When you switch on your set for the first time, the menu
LANGUAGE
automatically appears on the screen.The explanation appears in different languages
one at a time. Choose your own language and press the OK key on the remote
control.
Go on to page 4.
3Preparation
Preparation
CABLE
R6 / AA
B
w
æ b
SQ
VCR
MOVIE OTHERNEWSCHILDSPORT
TV DVD SAT
CDTUNER TAPE CDR
TV
4979.1 gb 06-01-2000 17:05 Page 3
4
Installation
Store TV channels
After the new or extra TV channels have been stored, the TV automatically transfers
those TV channels to the video recorder if it is equipped with the EasyLink function.
The message EasyLink : downloading ...... appears on the screen. The
programme list of the video recorder is now the same as the one of the TV. If the TV
is connected to a video recorder which supports the
NEXTVIEWLink function, the TV
also automatically transfers the language and country selections to the video
recorder.
First, select your language and country.
& Select Menu language and press the OK key.
é Select your language and press the OK key.
Use the cursor up/down to scroll through the list and to bring up other
languages which are not displayed on the screen at present.
“ Select Country and press the OK key.
‘ Select the country where you are now located and press the OK key.
Use the cursor up/down to scroll through the list and bring up other
countries which are not displayed on the screen at present.
Select
Other when none of the countries applies.
You can now search for and store the TV channels in two different ways:
using automatic installation or manual installation (tuning-in channel by
channel).
Select your choice and press the OK key.
Select the menu language and country
MENU TITLE
Menu language
Country
Automatic Installation
J INSTALLATION
MENU TITLE
United Kingdom
....
....
J Country
MENU TITLE
English
....
....
J Menu language
& Open the door of the remote control.
é Press U and f at the same time.
Installation
Select the
INSTALLATION
menu
& Use the cursor in the up/down, left/right directions to select a menu item.
é Press the OK key to activate.
“ Use the Ï key to return or to switch the menu off.
To use the menus
MENU TITLE
Subject 1
Subject 2
Subject 3
J Subject 4
Subject 5
Subject 6
J Subject 4 L M
o
œ
pπ
o
œ
pπ
213
546
879
0
i
¬V P
0
◊
U
X®qP
f
yÚ
h
ZOOM
INSTANT
213
B
w
æ b
Ï
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
SQ
MOVIE OTHERNEWSCHILDSPORT
OK
MENU
select menu item
return or switch
main menu off
activate
4979.1 gb 06-01-2000 17:05 Page 4
Searching for and storing TV channels is done channel by channel.
You must go through every step of the Manual installation menu.
Selection mode is only present and lights up if the country selected also
offers the channel option (C-channels for aerial channels, S-channels for cable
channels).
You can choose either channel or frequency mode.
& Select the TV system
Select the country or part of the world from where you want to receive the
TV channel.
If you are connected to a cable system, select your country or part of the
world where you are now located.
é Press the cursor down and enter the programme number with the digit keys.
“ Search for a TV channel
Press the cursor left/right.
The frequency or the channel number increases until a TV channel is found.
Direct selection of a TV channel
If you know the frequency, the C- or S-channel number, enter it directly with
the digit keys 0 to 9.
Ask for a list from your cable company or dealer, alternatively consult the
Table of frequencies on the inside backcover of this handbook.
‘ Fine tune
In case of poor reception, you can improve the reception by adjusting the
frequency with the cursor left/right.
( To store your TV channel, select Store and press the OK key.
Repeat steps
& to ( to store another TV channel.
§ To exit from the menu press the Ï key on the remote control.
In the Automatic installation menu select
Start and press the OK key to
activate the searching. All TV channels are searched for and stored
automatically.
If a cable system which broadcasts ACI (Automatic Channel Installation) or a
TV channel transmitting a teletext page with the frequencies and programme
names of all the TV channels which can be received, is detected, the search is
stopped and a programme list appears.
The programme list is automatically filled with all the programme numbers
and names of the TV channels transmitted.
It is possible that the cable company or the TV channel displays a broadcast
selection menu. Layout and items are defined by the cable company or the TV channel.
Make your choice with the cursor and press the OK key.
To exit from the menu press the Ï key on the remote control.
Go on to page 6.
5Installation
Manual installation
Automatic installation
Automatic installation
Start
Stop
TV is searching
One moment please ...
J Stop K
Automatic installation
Start
Stop
1 BBC1
2 BBC2
3 CNN
....
....
J Start K
Manual installation
(Selection mode)
System
Programme no.
Search
Fine tune
Store
J System K
4979.1 gb 06-01-2000 17:05 Page 5
6
Installation
Give name
It is possible to change the name stored in the memory or to assign a name
to a TV channel which has not yet been entered.A name with up to 5 letters
or numbers can be given to the programme numbers 0 to 99. For example
SUPER, BBC1,...
Between 99 and 0 you can also name any peripherals that are connected to a
euroconnector.
& Select Give name in the INSTALLATION menu and press the OK key.
é Select the programme number.
“ Press the OK key.
‘ Select the character with the cursor up/down.
( Select the following position with the cursor right.
§ Select the following character.
è Press the OK key when finished.
! Press the Ï key to return to the INSTALLATION menu.
Space, numbers and other special characters are located between Z and A.
According to your preference you can change the order of the stored TV
channels.
& Select Reshuffle in the INSTALLATION menu and press the OK key.
é Select the programme number you want to exchange.
“ Press the OK key.
‘ Select the new number you want to exchange it with.
( Press the OK key.
Repeat the operation until all TV channels are allocated as you like.
§ Press the Ï key to return to the INSTALLATION menu.
Reshuffle the programme list
After leaving the installation you can browse through the TV channels by
pressing the - P + key. Only those TV channels which are in the favourite list
will be displayed. Non-favourite TV channels can still be selected with the digit
keys. By default all stored channels are added to the favourite list.
& Select Favourite programmes in the INSTALLATION menu and press
the OK key.
é Select your favourite programme number.
“ Select Ye s or No with the cursor left/right.
‘ Repeat for every TV channel you want to make a favourite or a
non-favourite TV channel.
( Press the Ï key to return to the INSTALLATION menu.
In order for
NEXTVIEW to function properly, the first TV channel from the favourite list
should also broadcast the correct local date and time via teletext.
Select Favourite TV channels
INSTALLATION
Menu language
Country
Automatic installation
Manual installation
Give name
Reshuffle
Favourite programmes
SETUP
J Give name
Give name
EXT1
EXT2
EXT3
FRONT
0
1 BBC1
2 BBC2
3 ....
4 ....
5 ....
J 0
Reshuffle
EXT1
EXT2
EXT3
FRONT
0
1 CNN
2 BBC2
3 ....
4 ....
5 ....
J 1 CNN
Favourite programmes
0 ... No
1 ... Yes
2 ... No
3 .... No
4 .... Yes
5 ....
J 2 ... Yes
4979.1 gb 06-01-2000 17:05 Page 6
7Installation
The Setup menu allows you to adjust initial settings, i.e. those which are not
related to the installation of the TV channels.
The Setup menu contains items that control the settings of the TV’s functions,
features, services and peripherals you may have connected.
& Use the cursor in the up/down, left/right directions to select the menu item.
é Use the OK key to activate.
“ Use the Ï key to return or switch menu off.
Digital sources
See Connect Peripheral Equipment, p. 23 to connect your digital equipment,
like a DVD, a digital satellite tuner or a similar digital device.
Define Decoder/Descrambler programme numbers
If a decoder or a descrambler is connected, see p. 22, you can define one or
more programme numbers as decoder programme numbers.
Press the cursor left/right to select the input used to connect to your
decoder
Off, EXT1 or EXT2.
Select
Off if you do not want the selected programme number being
activated as a decoder programme number.
Select
EXT2 when the decoder is connected to your EasyLink video recorder.
When selecting the decoder, the message EasyLink: downloading presets....
appears on the screen.
Picture tilt
Select
Picture tilt with the cursor up/down.
Keep the cursor left/right pressed to adjust the rotation of the picture.
Information line
Select
On and after the selection of a TV programme or after pressing the
i key on the remote control, a TV channel which broadcasts teletext may
transmit the name of the TV channel, the programme name or another
message.This is displayed on screen next to information about sound and
picture format.
When selected
Off, only sound and picture format information is displayed
after the selection of a TV channel or after pressing the i key.
Factory settings
Select
Factory settings and press the OK key to restore picture and sound
settings, predefined in the factory.
Install TV Setup
INSTALLATION
Menu language
Country
Automatic installation
Manual installation
Give name
Reshuffle
Favourite programmes
SETUP
J SETUP
Decoder/Descrambler
Programme
Decoder status
J Programme
SETUP
Digital Sources
Decoder/Descrambler
Picture tilt
Information line
Factory settings
NEX
TV
IEW
provider none, 0...99
Auto format yes/no
INSTALLATION
J Digital sources
4979.1 gb 06-01-2000 17:05 Page 7
8
Installation
NEXTVIEW provider
Most broadcasters in Europe are offering teletext pages containing the day’s
programme schedule.These pages can be requested by switching the TV to
Teletext Guide.
An increasing number of broadcasters are offering an extended programme
guide service called
NEXTVIEW.
NEXTVIEW is a new way of presenting programme schedules and offers more
features than basic teletext.With
NEXTVIEW it is possible to show for instance
all the movies or children programmes for tonight or the following days.
If you select None as
NEXTVIEW provider, the TV will capture all data from
the available TV channels which broadcast
NEXTVIEW. Broadcaster defined
menus will not be available.
If you select a programme number of a TV channel stored in the favourite list
as
NEXTVIEW provider, the selected TV channel will provide NEXTVIEW data
and additional information of its own broadcasts as well as from other (non
selected) TV channels.
Normally you will select the
NEXTVIEW provider that transmits most
information in your language.You can make the best selection via information
from TV announcements or from the newspapers.
Important:
In order for
NEXTVIEW to function properly, the first TV channel from the favourite list
should also broadcast the correct local date and time via teletext.
Please check at startup if the time and date are correct in the NEXTVIEW screen.
Remark:
Not all TV channels support
NEXTVIEW.
How to make use of
NEXTVIEW, see p. 14.
Auto Format
Selecting
Ye s causes the screen to automatically fill as much of the picture as
possible when TV programmes are not carrying special signals detecting the
correct screen format.
With the q key on the remote control you can still select other picture
formats. See p. 11.
Installation
Select
Installation and press the OK key to return immediately to the
INSTALLATION menu.
‘ To exit from the menu press the Ï key repeatedly.
SETUP
Digital Sources
Decoder/Descrambler
Picture tilt
Information line
Factory settings
NEX
TV
IEW
provider none, 0...99
Auto format yes/no
INSTALLATION
J
NEX
TV
IEW
provider none/o...99
4979.1 gb 06-01-2000 17:05 Page 8
9Use of the remote control
Operation
Use of the remote control
M h a
SMART
ACTIVE
CONTROL
SMART
PICTURESOUND
213
546
879
0
B
w
®
Ò
‡π
†
æ b
Ï
i
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
0
◊
SQ
MOVIE SPORT CHILD NEWS OTHER
OK
MENU
w Select peripherals
Press this key repeatedly to select
EXT1,
EXT2, EXT3 or FRONT, according to where
you connected the peripherals (p. 25).
TV VCR DVD SAT TUNER CD TAPE CDR
Press one of these keys to use the remote
control directly in the TV, video recorder,
DVD or satellite mode. A green indicator
lights up. Press the same key again within 3
seconds to use the remote control in the
mode indicated below the key (tuner, CD,
tape or CD-recordable).
A red indicator lights up.
Press the key again to return to the function
mentioned above the key.
B Standby
The set is switched off and the red indicator
(orange when acquiring
NEXTVIEW
information) lights up.When acquiring
NEXTVIEW the TV is switched to full standby
after a period of max. 1 hour and the red
indicator lights up.
To switch the TV on again, press - P + or the
digit keys.
If your EasyLink video recorder has the
system standby function and you press the
standby key for 3 seconds, both the TV and
video recorder are switched to standby.
®Ò‡π†Video recorder see p. 25
æ NEXTVIEW on/off see p. 14
OK Press this key to activate your choice,
when in the menus.
S Freeze
To activate/de-activate the frozen picture and
to hold a teletext page.
Q Incredible Surround
In
MONO sound mode, this feature, when
switched on, enables you to hear a spatial
effect of sound.
In
STEREO sound mode, when Incredible
Surround On
is selected, it seems as though
the loudspeakers are spread further apart
from one another
i Screen information
Press for 5 seconds to activate/de-activate
the extended or reduced display of TV
channel and programme information on the
screen.
Press briefly to display information about the
selected TV channel and programme, the
sound reception, picture settings and the
remaining time set with the sleeptimer.
0/9 Digit keys
To select a TV channel.
For a two digit programme number, enter the
second digit within 2 seconds.
To switch immediately to a selected one digit
TV channel, keep the digit key pressed a bit
longer.
0 Previous programme
The previously selected TV channel is displayed.
The ◊ indication is only video recorder/DVD.
Use of the remote control
b Teletext on/off see p. 19
Ï Main menu on/off see p. 12
V Volume
Press + or - to adjust the volume.
¬ Mute
Temporarily interrupt the sound or restore
it.
P Programme selection
To browse through the TV channels
activated in the Favourite Programme menu.
4979.1 gb 06-01-2000 17:05 Page 9
10
Use of the remote control
213
546
879
0
B
w
æ
Ï
i
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
0
◊
Q
OK
MENU
fU
X®q P
f
yÚ
h
ZOOM
INSTANT
b
S
bcdfi
Mah
SMARTSMART
ACTIVE
CONTROL
MOVIE SPORT CHILD NEWS OTHER
h Active control
Active control is a pro-active and automatic
system.The TV continuously measures and
corrects all incoming signals in order to
provide the best picture possible.
Press the h key to select the Active
Control values Off or On.
Off Sharpness and Dynamic Contrast are
controlled automatically
On Sharpness, Dynamic Contrast and Noise
Reduction are controlled automatically.
Press the cursor in the up/down directions
while the selected Active Control setting
information is on top of the screen.
The Active Control menu appears.
The picture settings are being adapted
continuously and automatically.
The menu items cannot be selected.
Press the cursor in the up/down directions
again to switch off the menu.
c no function
b Dual Screen
& Press the b key to switch on Dual Screen.
The TV screen is divided into 2 parts:
- the left side for the normal main
picture,
- the right side for teletext broadcast by
the selected TV channel or for
NEX
TVIEW/Teletext Guide.
To operate
NEXTVIEW/Teletext Guide,
see p. 14.To operate teletext, see p. 19.
If Dual Screen is Off, the picture, teletext or
NEXTVIEW/Teletext Guide are displayed full
screen.
é Press the q key under the door of the
remote control to select a vertical squeezed
or a non vertical squeezed picture size
“ Press + P - to run through the teletext
pages.
‘ Select still teletext picture
Press the d key to freeze only the
teletext picture.The info in this page is not
being updated by the teletext broadcaster.
( When in Teletext Dual Screen, press the
b key to return to a full picture screen.
Press the b key to return to a full Teletext
screen.
§ When in NEXTVIEW/Teletext Guide Dual
Screen, press the æ key to return to a full
picture screen.
Press the b key to return to a full
NEXTVIEW/Teletext Guide screen.
fi Strobe
Press this key to reproduce the picture image
by image.
Press the fi key again to have a faster speed.
Press the fi again to switch off the strobe
function.
U Time display
The time, downloaded from the TV channel (with teletext)
stored on programme number 1 or the lowest favourite
programme number, is displayed on the screen.
This function is not available when continuous subtitles have been
switched on.
SUfh Teletext functions
see p. 20
4979.1 gb 06-01-2000 17:05 Page 10
11Use of the remote control
U
X®qP
fh
INSTANT
ZOOM
yÚ
213
546
879
0
B
w
®
Ò
‡π
†
æ b
Ï
i
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
0
◊
SQ
MOVIE SPORT CHILD NEWS OTHER
OK
MENU
bcdfi
Mah
SMARTSMART
ACTIVE
CONTROL
X Bilingual choice and
sound mode selection
Press this key
• to switch from
Stereo to Mono sound, in
case of stereo transmission, or from
Nicam Stereo to Nicam available, in case
of digital transmission;
• to choose between language Y (Dual Y) or
language Z (Dual Z), in case of bilingual
transmission.The setting is separately
stored for each TV channel.
® Instant record
If your video recorder has the EasyLink
function the
INSTANT ® key for record can
be operated in the TV mode.
q Picture format
Press this key repeatedly to select another
picture format: 4:3, Movie Expand 14:9,
Movie Expand 16:9 with or without subtitling,
Wide Screen, Super Zoom or Automatic
(when Auto format is set to Yes in the
SETUP menu).
Auto format makes the picture to fill the
screen as much as possible.
Sometimes also video recorder programmes
carry special signals which will automatically
switch the TV to the correct screen format.
Auto format is disabled when in Dual screen.
When in Movie Expand 14:9 or 16:9 or
Super Zoom picture format you can make
subtitles visible with the cursor up/down.
P no function
Select TV channels by theme
If programmes in the TV guide of
NEXTVIEW
have defined themes, it is possible to quickly
select TV programmes with the coloured
keys.
& Press the red, green, yellow or blue key
to select one of the four predefined
theme categories
MOVIES, SPORTS,
CHILDREN, NEWS.
The TV switches to the first TV channel
broadcasting a programme of the
selected theme. At the same time a list
of all the TV channels currently
transmitting a programme of the selected
theme appears on the screen.
é Use the cursor up/down to select a TV
channel.
“ Press the same colour key again to
remove the list.
‘ Under the white key you can programme
your own theme category.
(Default; the theme category
Shows has
been preprogrammed in the factory.)
Press the cursor up and select a
preferred theme from the theme list
with the cursor left/right.
From now on the selected theme
category is stored under the white key.
A list of all the TV channels currently
transmitting a programme of the selected
theme appears on the screen.
Smart Keys
To select predefined picture and sound settings.
M Smart Sound
Each time it is pressed, a different sound setting is selected, corresponding with
specific factory setting of Treble and Bass.
a Smart Picture
Each time it is pressed, a different picture setting is selected, corresponding with
specific factory settings of Contrast, Colour, Sharpness and Dynamic Contrast.
Personal refers to the personal preference settings of picture and sound selected
in the picture and sound menu.
Remark: the moment you are in a predefined smart sound or picture setting and you
modify a setting in the picture or sound menu, all values of the menu will overwrite the
previously made settings.
4979.1 gb 06-01-2000 17:05 Page 11
12
Use of the menus
& Press the Ï key to display/cancel the MAIN MENU.
é Use the cursor in the up/down directions to select the PICTURE, SOUND or
FEATURES menu or to select the PROGRAMMES.
“ Press the cursor right to activate the selected menu.
‘ Use the cursor in the up/down, left/right directions to select the menu item.
( Use the OK key to activate.
§ Press the Ï key repeatedly to return or to switch the menu off.
Picture menu
If an NTSC peripheral is connected to one of the euroconnectors, the option Hue
also appears.
Tint
Select the colour temperature:
Normal, Warm or Cool.
Digital Scan (Line Flicker Reduction)
In Movie Expand picture format, Digital Scan is always active.
The menu item is not available.
In rare circumstances while watching TV programmes it may be preferable to
switch off the digital scan line flicker reduction. Normally keep it switched on.
Press the cursor left/right to select
On of Off.
Dynamic Contrast
To make the contrast in the darker and the brighter picture areas more
noticeable, select the
Med setting.
In certain circumstances it may be preferred to select
Min, Max or Off.
The modified adjustments for Contrast, Brightness, Colour, Sharpness,Tint,
Digital Scan and Dynamic Contrast are automatically stored for all TV
channels.
Select
Factory settings in the Setup menu to restore the predefined factory
settings, see p. 7.
Sound menu
The modified adjustments for Volume, Balance,Treble and Bass are
automatically stored for all TV channels.
Select
Factory settings in the Setup menu to restore the predefined factory
settings, see p. 7.
Headphone volume
See Connect Peripheral Equipment, p. 24 for the connection of the
headphone.
Press the Ï key to return to the
SOUND menu.
Use of the menus
PICTURE
Contrast
Brightness
Colour
Sharpness
Tint
Digital Scan
Dynamic Contrast
J Contrast L M
MAIN MENU
Contrast
SOUND
FEATURES
PROGRAMMES
J PICTURE
OK key to activate
cursor to select
adjustments
return or switch
main menu on/off
213
546
B
w
æ b
Ï
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
SQ
MOVIE OTHERNEWSCHILDSPORT
OK
MENU
SOUND
Volume
Balance
Treble
Bass
Headphone volume
J Volume L M
4979.1 gb 06-01-2000 17:05 Page 12
13Use of the menus
Features menu
& Press the Ï key to display/cancel the MAIN MENU.
é Use the cursor in the up/down directions to select the FEATURES menu.
“ Press the cursor right to activate the selected menu.
‘ Use the cursor in the up/down directions to select a menu item.
( Use the cursor in the left/right directions to select the desired setting.
Sleeptimer
With the sleeptimer you can set a time period after which the TV should
switch itself to standby.
The counter runs from
Off up to 180 min.
One minute before the TV is set to go to standby, the remaining seconds
appear on screen. Not visible in dual screen mode.You can always switch off
your set earlier or change the set time.
Child lock
If the child lock is on, the TV can only be switched on with the remote
control.The P - and + keys in front of the TV cannot be used to select a TV
channel. In this way you can prevent unauthorised use of your TV.
If the message
Child lock On appears, the child lock must be switched off
before you can use the P - and + keys in front of the TV to select a TV
channel.
Subtitle
TV channels with teletext often transmit certain programmes with subtitling.
See Teletext, Continuous Subtitles, p. 21 how to select the proper subtitle
page from the teletext index.
Select
Subtitle On or Off.
Press the Ï key to switch off the Features menu.
Programme list
& Press the Ï key to display/cancel the MAIN MENU.
é Select PROGRAMMES with the cursor up/down.
“ Press the cursor right to display an overview of all the TV channels installed.
‘ Press the cursor up/down to run through the list and press OK to select the
desired TV channel.
( Press the Ï key to switch off the Programme list.
Sleeptimer Off
Child lock Off
Subtitle Off
J FEATURES
OK key to activate
cursor to select
adjustments
return or switch
main menu on/off
213
546
B
w
æ b
Ï
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
SQ
MOVIE OTHERNEWSCHILDSPORT
OK
MENU
4979.1 gb 06-01-2000 17:05 Page 13
14
NEXTVIEW
In the Setup menu, p. 8 you were asked to select a NEXTVIEW provider.
If the selected provider supports
NEXTVIEW then the TV will automatically
present the
NEXTVIEW programme schedule. If the TV channel supports just
teletext, then the TV will switch automatically to Teletext Guide.
Both facilities are offering the same functions: record, remind, info and watch.
However in case of Teletext Guide the broadcaster is responsible for the
availability of these functions.
Some broadcasters provide information about their own programmes and
sometimes other TV channels for one or more days.You can search for the
programmes you want to watch up to 7 days in advance. It is also possible to
search for a programme by theme, e.g. sport, movie, etc. Once a programme
has been selected it can be tagged, to remind you, or to record on the video
recorder automatically (provided the video recorder is equipped with
NEXTVIEWLink), once, daily, weekly or series.
Teletext Guide/
NEXTV
IEW also allows direct access to detailed information
about programmes if provided by the broadcaster.
The broadcaster is responsible for the content of the information.
The TV is responsible for the capture of that information and for the presentation to
the user.
Use of the Teletext Guide/
NEX
TVIEW
menus
& Press the æ key on the remote control to display/cancel the Teletext Guide/
NEXTVIEW menu.
é Use the cursor in the up/down, left/right directions to select the date, DAY
for the daily guide and the time block (in steps of 15 minutes), CHANNEL for
the channel guide,
THEME for the theme guide, OVERVIEW for an overview
of all the programmes which are marked as reminders or for recording, the
programme guide page number or to enter the programme list.
NEXTVIEW / Teletext Guide
Teletext Guide NEXTVIEW
“ Enter the proper programme guide page number
with the digit keys or with the – P + keys.
‘ Press the cursor left/right to run through the
subpages.
( Select a programme with the cursor up/down.
§ Press one of the colour keys to select one of the
basic functions (if available);
record, remind, watch,
info. See Basic functions further on.
è Press the OK key to return to the header area
again.
“ Select a programme with the cursor up/down.
‘ Press one of the colour keys to select one of the
basic functions (if available);
record, remind, watch,
info. See Basic functions further on.
( Press the OK key to return to the header area
again.
OK key
to activate
cursor to select
adjustments
213
546
B
w
æ b
Ï
SQ
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
MOVIE OTHERNEWSCHILDSPORT
OK
MENU
æ
NEX
TVIEW
selection
Menu Day Channel Theme Overview
BBC1 BBC2
p.202 p 01 02 ... π
BBC1
11.03 ................
14.35 ................ 226/3
17.50 ................ 231
Record
Remind
Info
Watch
Monday 9 Oct 18:03
Menu Day Channel Theme Overview
CNN BBC1 BBC2
BBC1
NEX
TV
IEW
What’s on now
Preview
Themes
Ratings
Record
Remind
Info
Watch
4979.1 gb 06-01-2000 17:05 Page 14
15NEX
TVIEW
Teletext guide
TV channels which broadcast teletext also transmit a page with the
programme guide of the day. For each selected TV channel the programme
guide page can be selected with the æ key:
- automatically if the selected TV channel supports services like PDC
(Programme Delivery Control) or MIP (Magazine Inventory Page).
- if automatic pre-selection is not possible then the index page is displayed
and the proper programme guide page number of the selected TV channel
has to be entered with the digit keys.
The programme guide page will be stored automatically only if it satisfies
Video Programming via Teletext (VPT) requirements.
Every time you press the æ key, the programme guide page of the
selected TV channel will be available if the TV channel does not support
NEXTVIEW.
The function items record, remind, info and watch, corresponding with the
coloured keys, become highlighted if the displayed programme page satisfies
the Video Programming via Teletext (VPT) requirements. Select a programme
item and press one of the function keys, e.g. Record or Remind. See Basic
functions further on.
The Info item is enabled if the selected programme contains a page number
with an optional subcode referring to a page with more info about the
programme.
NEXTVIEW modes to sort and represent information
Menu
If in the Setup menu, see p. 8, you have selected a TV channel as
NEXTVIEW
provider which also supports NEXTVIEW. NEXTVIEW menu is displayed or can
be selected.The selected TV channel is responsible for this menu.
The
NEXTVIEW menu appears when NEXTVIEW is switched on.
Use the cursor up/down to select a menu item.
Use the cursor right to select the menu item.
While going through the menus, the TV is collecting the sorting criteria to
finally display a list of programme events.
The functions, in the left column, are shown at reduced brightness as long as
the menu is displayed.
If
None has been selected as NEXTVIEW provider in the Setup menu, the
broadcaster’s defined menu will not be available.
Menu Day Channel Theme Overview
BBC 2
p.202 p 01 02 ... π
BBC 2
11.03 ................
14.35 ................ 226/3
17.50 ................ 231
One moment please
Record
Remind
Info
Watch
Monday 9 Oct 18:03
Menu
BBC1
NEX
TV
IEW
What’s on now
Preview
Themes
Ratings
Record
Remind
Info
Watch
4979.1 gb 06-01-2000 17:05 Page 15
16
NEXTVIEW
Day
The day guide provides an overview of all programme titles active in the
selected time block.Time blocks are 15 minute intervals starting from the
current time of the current day.
The default order is based on the programme list of the favourite TV channels
as stored in the installation of the TV.TV channels not marked as favourite TV
channels will not appear.
Default
NEXTVIEW opens with the day screen if the broadcast does not have
its own menu.
Channel
The Channel guide provides an overview of all programmes that are
broadcast by a single channel during one day.
Previous programmes can be made visible via cursor up.
The list will start with the earliest broadcast programme.
With cursor left/right another favourite TV channel can be selected.
Theme
The theme guide displays a list of all programmes at the selected date, that
matches with the selected category (news, sport, culture, movies, …).
The default starting item will be the current or next programme on the
current TV channel.
The
THEME selection is only present if programmes in the TV guide have
defined themes.
Overview
The Overview menu provides a list of programmes that are marked as
reminders and those that have to be recorded.
When more than one programme to be recorded has an overlap in time,
these programmes will be marked by a red colour.
After the programme has been broadcast, all items set for once will be
deleted from the list the following day.This menu can be used to change a
reminder or programmes to be recorded.
Note: the TV will automatically interpret the broadcast time (as shown on the
teletext guide) of your selected programme into the correct local time and
date.
Monday 9 Oct 18:03
Channel
CNN BBC1 BBC2
BBC1
NEX
TV
IEW
........
........
........
Record
Remind
Info
Watch
Monday 9 Oct 18:03
Theme
Series Movies News
BBC1
NEX
TV
IEW
BBC1
CNN
TVE
Record
Remind
Info
Watch
Monday 9 Oct 18:03
Overview
BBC1
NEX
TV
IEW
BBC1 17.10 .............
CNN 17.30 .............
TVE 18.05 .............
BBC2 19.00 .............
Record
Remind
Info
Watch
Record
Remind
Info
Watch
Info block
Monday 9 Oct 18:03
Day
p I 18.03-18.15 π 18.30
BBC1
NEX
TV
IEW
J channel - start - prog.
4979.1 gb 06-01-2000 17:05 Page 16
17NEX
TVIEW
Basic functions
The functions Record, Remind, Info and Watch can be activated with the
corresponding colour keys on the remote control.
If the function is not available, then the text is shown at reduced brightness.
Select a programme with the cursor up/down.
Record R or Remind !
& Press the red colour key to activate Record or the green colour key to
activate
Remind
.
If the programme number of the broadcaster is not yet known, a message appears
with the request to input the right number.
A small menu pops up in which you can choose the interval: once, daily or
weekly, or clear an earlier made record or remind setting.The default interval
is set to
Once. If a programme is an episode of a series, it is identified by the
system and the options
daily and weekly are replaced by the option series.In
this case the system identifies when the next episode of the series will be
broadcast.This is not possible in the Teletext guide.
é Use the cursor in the left/right directions to select the interval.
The colour of the tag refers to the interval.
“ Press the OK key.
When
Record R is activated:
Storing is displayed to indicate the video recorder is programmed.
When
Remind ! is activated:
- a message will be displayed the moment the tagged programme
with ! starts, when watching the TV later on.
- the TV switches on the moment the tagged programme with ! starts,
when the TV is in standby.
Note: Recordings and reminders are not possible when the broadcaster does not
transmit dates and times of the programmes.
The message
No TV programming possible appears.
Make sure you are on the TV programming page.
Info
& Press the yellow colour key to activate Info.
Advertisements or information relating to the selected programme are
displayed. In some cases all of the information does not fit on the screen. Use
the cursor up/down to browse through all the information.
é Press the yellow colour key again to switch off the information.
Watch
Press the blue colour key to activate
Watch.
This function is only available if a currently broadcast programme is selected.
Otherwise the function is not available.
The selection causes the TV to tune to the selected TV channel.
NEXTVIEW is
switched off.
R
!
Record
Remind
Info
Watch
Info block
Date Time
Channel
CNN BBC1 BBC2
BBC1
NEX
TV
IEW
11.03 Travel Guide
14.35 World news
17.50 Insight
R
!
p
Once
π
Daily Weekly Clear
4979.1 gb 06-01-2000 17:05 Page 17
18
NEXTVIEW
Select Picture/NEXTVIEW-Teletext Guide
Press the æ key.
Press the b key.
The screen is divided into two parts: the left side for the normal main picture,
the right side for
NEXTVIEW/Teletext Guide.
Press the b key to return to a full
NEXTVIEW/Teletext guide screen.
Press the æ key to return to a full picture screen.
Acquisition and updating of
NEXTVIEW information
Acquisition and updating of NEXTVIEW is done when you are watching the TV
channel of the selected
NEXTVIEW provider, see Setup menu p. 8, or when the
TV is switched to standby.
The indicator on the front of the TV remains orange during standby.
After all needed acquisition or updating is complete, it turns red.
Acquisition of fresh data will happen once during the night.
Note: it may be necessary to put the TV in standby mode when all
NEXTVIEW
information is outdated, e.g. returning from holiday.
Video recorder restrictions with NEXTVIEW
The Record item and the automatic recording will only be present and
possible if your video recorder is equipped with
NEXTVIEWLink.
Your video recorder should be connected to
EXTERNAL 2. See Connect
Peripheral Equipment, p. 22.
The daily, weekly and series options, the number of recordings set and the
way overlapping recordings are managed, depend on the type of video
recorder you have.When all video recorder timers are full, the item
Record
in the menu will not be present.
Upload video recorder overview (only with Philips sets)
When the TV is switched on, the timer recordings are uploaded to the TV to
check if any manual addition or deletions have been done.This is shown in the
overview.
The video recorder manages and removes timer recordings when performed.
Some
NEXTVIEWLink video recorders do not allow a daily programming of the
recording to start on a Saturday or Sunday. In this case the item
daily will be
removed from the menu on those days.
213
546
879
0
B
w
æ b
Ï
i
TV VCR DVD SAT
TUNER
MOVIE SPORT CHILD NEWS OTHER
CD TAPE CDR
¬V P
0
◊
SQ
OK
MENU
b cdfi
Mah
SMARTSMART
ACTIVE
CONTROL
b
æ
4979.1 gb 06-01-2000 17:05 Page 18
19Teletext
Most TV channels broadcast information via teletext.
Each channel which broadcasts teletext transmits a page with information on
how to use its teletext system. Look for the teletext page with the main
index (usually p. 100).
Depending on the TV channel, teletext is transmitted in different systems.
The colours used in the options line correspond with the colour keys of your
remote control.
About Easy Text
Easy Text considerably reduces the waiting time (on condition that the
teletext broadcast of the particular TV channel is received for at least half a
minute) by :
• a direct selection of previous and following pages which are in transmission
and of the pages referred to in the options line
• a habit watcher list: frequently used pages are put automatically in a list of
preferred pages, so that they are immediately available
• the precapturing of the page numbers referred to in the displayed page
• the precapturing of all the subpages.
Switch Teletext on and off
Press b to switch the teletext on or off.
The main index page appears on the screen together with two information
lines at the top and one option line at the bottom of the screen.
Remark: if the displayed teletext characters on screen do not correspond with the
characters used in your language, press the X key, under the door of the remote
control, repeatedly to select Language group 1 or 2.
Select a Teletext page
With the digit keys
Enter the desired page number with the digit keys.
The page counter seeks the page or the page appears immediately when the
page number has been stored in the memory.
A message appears when you have entered a non existent or incorrect page
number. Page numbers beginning with 0 or 9 do not exist. Choose another number.
With the option line
Select with the colour keys, corresponding to the coloured options at the
bottom of the screen, the desired subject.
Select Picture/Teletext
Select a TV channel which broadcasts teletext.
Press the b key.
The screen is divided into two parts:
the left side for the normal main picture,
the right side for teletext broadcast by the selected TV channel.
Press the b key to return to a full screen picture.
Press the b key to return to a full teletext picture.
Quickly run through the teletext pages
Press the cursor up/down or the - P + key to run through the previous or
the following pages.
Select the previously selected txt page
Press the 0 key.
Teletext
cursor to select
pages
colour keys to
select
213
546
879
0
B
w
æ b
Ï
i
SQ
TV VCR DVD SAT
TUNER CD TAPE CDR
¬V P
0
◊
OK
MENU
b
0
X
U
X ®qP
f
yÚ
h
ZOOM
INSTANT
879
0
i
0
◊
b cdfi
Mah
SMARTSMART
ACTIVE
CONTROL
b
4979.1 gb 06-01-2000 17:05 Page 19
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
in altre lingue
- English: Creative ZEN - 1 User manual
Documenti correlati
Altri documenti
-
Philips 42 pf 9945 Manuale utente
-
Philips TV Manuale utente
-
-
Philips 29PT8618 Manuale del proprietario
-
-
-
-
-
Philips 37PF9986/12 Manuale utente
-
Philips 12 Manuale del proprietario