Shindaiwa PT262S Manuale utente

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

PT-262S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RÈGLES DE

SECURITÉ. LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND

BEFOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE IN

CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA DELLE

ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

1Cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

POLE PRUNER

PT262S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Contents

For safe use of your product............................................................................................... 3

Description.......................................................................................................................... 8

Before you start .................................................................................................................. 9

Packing list ....................................................................................................................9

Assembly ....................................................................................................................... 9

Preparing the fuel ........................................................................................................ 11

Lubricating the guide bar and saw chain ..................................................................... 12

Engine operation............................................................................................................... 13

Starting the engine ...................................................................................................... 13

Stopping the engine..................................................................................................... 14

Pruning operation ............................................................................................................. 15

Pruning techniques...................................................................................................... 16

Maintenance and care ...................................................................................................... 17

Servicing guidelines..................................................................................................... 17

Maintenance and care ................................................................................................. 17

Storage ........................................................................................................................ 24

Specifications.................................................................................................................... 25

Declaration of conformity .................................................................................................. 27

3

For safe use of your product

For safe use of yo ur product

Important information

WARNING

Please ensure that you read the operator's manual before using your product.

About your operator's manual

 This manual contains necessary information about the assembly, operation, and maintenance of your product.

Please read it carefully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference val-

ues, and there may be a slight conversion error in some cases.

Failure to do so could lead to an accident or serious injury.

Intended use of this product

 This product is designed for light to medium trimming of limbs and branches up to 203 mm in diameter.

 Do not use this unit for any purpose other than aforementioned.

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 Please consult your dealer if anything is unclear or of concern.

Failure to do so could lead to an accident or serious injury.

Do not modify the product

 You must not modify the product.

To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be

covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained

 You must not use the product unless it has been checked and maintained. Always ensure that the product is checked

and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

 When loaning your product to another party, ensure that the person borrowing the product receives the operator's

manual along with it.

 If you assign your product to another party, please enclose the operator's manual with the product when handing it

over.

Failure to do so could lead to an accident or serious injury.

Users of the product

 The product should not be used by:

 people who are tired

 people who have taken alcohol

 people who are on medication

 people who are pregnant

 people who are in poor physical condition

 people who have not read the operator's manual

 children

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

Failure to observe these instructions could lead to an accident.

 The ignition system of this product generates electromagnetic fields during operation. Magnetic fields can cause

pacemaker interference or pacemaker failure. To reduce health risks, we recommend that pacemaker users consult

their physician and the pacemaker manufacturer before operating this product.

 National or local regulation can restrict the use of this product.

4

For safe use of your product

Vibration and cold

 It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers. The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ailment is unknown.

 Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.

 Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by

not smoking.

 Limit the number of hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-

held power equipment is not required.

 If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, con-

sult your physician before exposing yourself further to cold and vibration.

Failure to observe these instructions could result in damage to your health.

Repetitive stress injuries

 It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive stress injury (RSI). To reduce the risk of RSI, do the following:

 Avoid using your wrist in a bent, extended or twisted position.

 Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the

repetitive movement.

 Do exercises to strengthen hand and arm muscles.

 See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-

nosed, the more likely permanent nerve and muscle damage can be prevented.

Failure to observe these instructions could result in damage to your health.

Proper training

 Do not permit operation without proper training and protective equipment.

 Be thoroughly familiar with the controls and proper use of unit.

 Know how to stop the unit and shut off the engine.

 Know how to unhook a harnessed unit quickly.

 Never allow anyone to use the unit without proper instruction.

Failure to observe these instructions could result in damage to your health.

Wear proper clothing.

 Secure hair so it is above shoulder length.

 Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the

unit.

 Do not wear open toed footwear, or go bare-foot or barelegged.

Failure to observe these precautions could result in damage to your sight or hearing, or lead

to a serious injury.

Wear protective gear

 Always wear the following protective gear when working with the pole pruner.

1. Head protection (helmet): Protects the head

2. Ear muffs or ear plugs: Protect the hearing

3. Safety goggles: Protect the eyes

4. Face shield: Protects the face

5. Safety gloves: Protect the hands from cold and vibration

6. Work clothes that fit (long sleeves, long trousers): Protect the body

7. Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes

(with toecaps): Protect the feet

Failure to observe these precautions could result in damage to your sight or hearing, or

lead to a serious injury.

 When necessary, please use the protective gear below.

 Dust mask: Protects the breathing apparatus

 Bee net: To deal with attacks by bees

WARNING

5

For safe use of your product

Warning notices

Other indicators

Environment of use and operation

 Do not use the product:

 under poor weather conditions.

 on steep slopes or in places which give no secure foothold and are thus slippery.

 at night or in dark places with poor visibility.

 When using the product on a gentle slope, work in a level, contour-like motion.

A serious injury could result if you fall or slip, or fail to operate the product correctly.

 For your own health and your safe and comfortable work, operate the machine within the air temperature range of

−5

o

C to 40

o

C.

Failure to observe these instructions could result in damage to your health.

Being prepared in case of an injury

 In the unlikely event of an accident or injury, please ensure that you are

prepared.

 First aid kit

 Towels and wipes (to stop any bleeding)

 Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help, the injury could

worsen.

Put safety first in the case of fire or smoke

 If fire comes from the engine or smoke appears from any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safety.

 Use a shovel to throw sand or other such material on the fire to prevent it from spreading, or put it out

with a fire extinguisher.

A panicked reaction could result in the fire and other damage becoming more extensive.

WARNING

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

6

For safe use of your product

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

Chain lubrication

Wear eyes, ears and head

protection

Petrol and oil mixture

Wear foot protection and

gloves

Choke Control "Cold Start"

Position (Choke Closed)

Emergency stop

Choke Control "Run" Position

(Choke Open)

Do not use the product in plac-

es with poor ventilation

Carburettor adjustment

- Idle speed

Beware of fire

Beware of high-temperature

areas

Beware of electric shocks

Guaranteed sound power lev-

el

Do not operate closer than

15 meters (50 feet) from elec-

trical hazards. Keep bystand-

ers at least 15 meters

(50 feet) away.

Engine start

Chain oiler adjustment Purge bulb (Primer)

Safety/Alert

7

For safe use of your product

Safety decal(s)

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

1. Part number X505-002372 2. Part number X505-002362

8

Description

1. Power head - Includes the Engine, Clutch, Fuel Sys-

tem, Ignition System and Starter.

2. Throttle trigger - Spring loaded to return to idle when

released. During acceleration press trigger gradually for

best operating technique.

3. Shoulder harness - An adjustable strap that suspends

the unit from the operator.

4. Cutting attachment

5. Cutting shoe - Used to capture and stabilize branch

while cutting. Place cutting shoe against branch, accel-

erate and lower saw chain into branch.

6. Guide bar

7. Saw chain

8. Automatic oiler assembly - Self oiling. Use high qual-

ity, low viscosity, non detergent bar and chain oil.

9. Lower shaft tube - Durable fiberglass mesh housing.

10. Suspension point - Device on which the harness shall

be hooked.

11. Stop switch - Mounted on top of handle assembly.

Move switch forward to run, back to stop.

12. Throttle trigger lockout - This lever must be de-

pressed before throttle trigger can be operated.

13. Throttle handle assembly - Sturdy handle for right

hand placement. Includes stop switch and throttle trig-

ger.

14. Top guard - Protects arm from hot engine.

15. Recoil starter - Pull recoil handle slowly until starter en-

gages, then quickly and firmly. When engine starts re-

turn handle slowly. Do not let handle snap back or

damage will occur.

16. Silencer cover - Cover the silencer not to make opera-

tor touch the hot surface of silencer.

17. Fuel tank - Contains fuel and fuel filter.

18. Fuel tank cap - Covers and seals fuel tank opening.

19. Purge bulb - Pumping purge bulb before starting en-

gine draws fresh fuel from the fuel tank, purging air from

the carburettor. Pump purge bulb until fuel is visible and

flows freely in the clear fuel tank return line. Pump purge

bulb an additional 4 or 5 times.

20. Air cleaner assembly - Contains replaceable air filter

element.

21. Choke - Located above air cleaner housing. Move lever

to starting position (Choke Closed) and back to run po-

sition (Choke Open).

22. Spark plug - Provides spark to ignite fuel mixture.

23. Guide bar cover - Used to cover guide bar and saw

chain during transport and storage. Remove guide bar

cover before using unit.

24. Type and serial number

9

Before you start

Packing list

 Power head and handle assembly

 Drive shaft assembly

 Cutting attachment with guide bar and saw chain

 Operator's manual

 Socket wrench

 L-wrench

 Safety goggles

 Shoulder harness

 Guide bar cover

Assembly

Handle shaft / drive shaft

1. Remove protective caps from handle shaft assembly.

2. Loosen clamping bolts (A) on drive shaft.

3. Pull flexible drive shaft coupler (B) 51 - 76 mm (2 -3 inches)

out of handle shaft.

4. Align flexible drive shaft coupler with drive shaft socket and

slide together until handle shaft is fully seated into drive

shaft.

5. Tighten clamping bolts (A).

Cutting attachment to drive shaft installation

1. Loosen the two screws (C) and locator screw (D) on cutting

attachment.

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

WARNING

 Read the operator's manual carefully to ensure that you assemble the product correctly.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

10

Before you start

2. Loosen clamp knob (E) turning anticlockwise.

3. Pull upper tube (F) out of fiberglass lower tube 127-152 mm

(5-6 inches), then slide (F) back into fiberglass lower tube

exposing inner drive shaft (G). Align and join star shaped

drive end of inner drive shaft (G) with cutting attachment

shaft (H).

4. Align ridges (J) on upper tube with seams in cutting attach-

ment.

5. Slide together aligning locator screw (D) in cutting attach-

ment with locating hole (I) in upper tube.

6. Tighten locator screw (D). Tighten two cutting attachment

screws (C).

7. Extend upper tube to desired length. Tighten center clamp

knob (E) turning clockwise.

Saw chain tension adjustment

1. Move stop switch to STOP position.

2. Disconnect spark plug cap.

3. Loosen two gearcase cover nuts (A) until finger tight.

4. Hold the bar nose up, and turn the adjuster screw (B) clock-

wise until the chain fits snugly against the underside of the

bar, as shown. Cold chain only - turn adjuster screw clock-

wise an additional 1/8 - 1/4 turn.

5. Tighten both gearcase cover nuts with nose held up. Tighten

rear nut first.

6. Pull the chain around the guide bar by hand. Reduce the

chain tension if you feel tight spots.

7. When chain is properly tensioned, tighten gear case cover

nuts securely.

WARNING

 Always disconnect spark plug cap before servicing cut-

ting attachment. Wear gloves when handling saw chain,

otherwise serious personal injury may result.

11

Before you start

8. Keep chain properly tensioned at all times.

9. Connect spark plug cap.

Preparing the fuel

Fuel

 Recommended mixture ratio; 50: 1 (2%) for ISO-L-EGD

Standard (ISO/CD 13738), JASO FC,FD grade and Shindaiwa

One 50: 1 oil.

 Do not mix directly in engine fuel tank.

Correct cold ten-

sion

Chain needs ten-

sioning

Correct warm

tension

Side link contact-

ing guide bar

Drive link tangs

hanging out of

guide bar

Three mm (1/8")

between side

link and guide

bar at bottom

IMPORTANT

 Tighten gearcase cover nuts to 8 - 9 N·m (71 - 80 in. lbs.)

Do not over-tighten nuts. Damage may result.

NOTE

 All chains require frequent adjustment.

DANGER

 Do not fuel up while the engine is hot or in operation.

 Do not smoke or hold a flame near when refuelling.

If you do so, the fuel could ignite and cause fire, leading to burns.

WARNING

 Do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground. Do not refuel the product on the load-

ing platform of a truck, or in other such places.

 Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

Otherwise, fuel may get spewed.

 Mop up any fuel that overflows or spills out due to overfilling.

Fuel spills can cause fire and burns when ignited.

 After refuelling, always check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,

or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product immediately and contact

your dealer to have it repaired.

Any fuel leaks could cause fire.

 Keep the refuelling tank in a shaded area away from fire.

 Use an approved fuel container.

IMPORTANT

 Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil of reputable brand name. Minimum 89 Octane

unleaded petrol is recommended. Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.

 Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days.

12

Before you start

Fuel supply

 Do not add so much fuel that it reaches the mouth of the fuel

tank (A). Keep the fuel within the prescribed level (up to the

shoulder level (B) of the fuel tank).

 Tighten the fuel tank cap securely after refuelling.

Lubricating the guide bar and saw chain

1. Wipe debris from around oil fill cap.

2. Remove oil fill cap and fill reservoir with a quality, low viscos-

ity guide bar and saw chain oil.

NOTE

 The discharge volume of the automatic oiler is preset to de-

liver 3 to 4 ml/min. at normal operating RPM. During heavy

or dry cutting conditions the oil discharge volume may be

adjusted to assure adequate lubrication. Refill the oil reser-

voir with each tank of fuel.

IMPORTANT

 To prevent plastic deterioration, do not use synthetic or sili-

cone based oil.

13

Engine operation

Starting the engine

Starting a cold engine

(Connect the spark plug cap if the product has been in storage for

a long period of time.)

1. Remove the guide bar cover.

2. Placing the product on level ground, check to ensure that the

cutting attachment does not come into contact with the sur-

face of the ground or any other impediment using a beam or

other such implement.

3. Move the ignition switch (A) to the Start position.

4. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

WARNING

Be particularly careful to observe the following precautions when starting the engine:

 Move at least 3m from the place where you refuelled.

 Place the product in a flat, well ventilated place.

 Check that there are no fuel leaks.

 Check that none of the nuts and bolts are loose.

 Leave plenty of space around the product and do not allow people or animals near it.

 Start the engine with the throttle trigger in the idle speed position.

 Hold the product firmly to the ground when starting the engine.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

 Check that there are no abnormal vibrations or sounds once the engine starts. Do not use the product if there are

abnormal vibrations or sounds. Contact your dealer to have it repaired.

Accidents involving parts that fall or shatter off can cause wounds or serious injury.

 The exhaust fumes from the engine contain toxic gases. Do not operate the product indoors or in other

ill ventilated places.

The exhaust fumes could cause poisoning.

 Do not touch silencer, spark plug, angle transmission, and other high temperature components while

the product is running or for some time after it stops.

You could burn yourself if you touch a high temperature component.

 Do not touch spark plug, spark plug wire, and other high voltage components while the product is run-

ning.

You could receive an electric shock if you touch a high voltage component while the product is running.

 If the cutting attachment rotates even though the throttle trigger is in the idle speed position when the engine is start-

ed, adjust the carburettor before using the product.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

NOTE

 Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.

 Do not let go of the starter grip as it returns.

14

Engine operation

5. Move the choke lever (F) to the "Cold Start" (E) position.

6. Alternately press and release the purge bulb (H) until the fuel

is sucked up into it.

7. Checking that the area around you is safe, hold the position

closest to the engine firmly as shown in the illustration, pull-

ing several times on the starter grip (I).

8. If you hear an explosion-like sound and the engine stops im-

mediately, move the choke lever to the "Run" (G) position

and continue pulling on the starter grip to start the engine.

9. If the engine does not stop, return the choke lever gently to

the "Run" position.

10. Leave the engine to warm up at idle speed for a while.

Starting a warm engine

1. Move the ignition switch (A) to the Start position.

2. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

3. Check that the choke lever is in the "Run" position.

4. If no fuel is visible in the purge bulb, alternately press and re-

lease the purge bulb until the fuel is sucked up into it.

5. Checking that the area around you is safe, hold the position

closest to the engine firmly, and pull on the starter grip to

start the engine.

Stopping the engine

1. Move the throttle trigger (B) to the idle speed position and set

the engine to idling (i.e. low speed).

2. Move the ignition switch (A) to the Stop position.

3. In the event of an emergency, stop the engine immediately

using the ignition switch.

4. If the engine fails to stop, move the choke lever to the "Cold

Start" position. The engine will stall and come to a halt (an

emergency stop).

 If the engine fails to stop when the ignition switch is used, have

the ignition switch checked and repaired by your dealer before

you use the product again.

5. Always disconnect the spark plug wire from the spark plug to

ensure the engine cannot be started before you work on the

unit or leave it unattended.

15

Pruning operation

DANGER

 All over head electrical conductors and communications wires can have electricity flow with high voltages. This unit

is not insulated against electrical current. Never touch wires directly or indirectly when pruning, otherwise serious

injury or death may result.

 The area within a 15 m radius of the product is a danger zone. Be careful to observe the following precautions while

working with the product.

 Do not allow children and other people or pets to enter the danger zone.

WARNING

 If the cutting attachment rotates even though the throttle trigger is in the idle speed position when the engine is start-

ed, adjust the carburettor before using the product.

 Do not start or operate unit unless all guards and protective covers are properly assembled to unit.

 Never reach into any opening while the engine is running. Moving parts may not be visible through openings.

 Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings.

 Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before

removing obstructions, clearing debris, or servicing unit.

Keep a solid stance

 Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfac-

es. Do not work in odd positions or on ladders. Do not overreach.

 Operate the product only from the ground or out of an approved bucket lift.

 Always evaluate the branches to be pruned for hazards such as loose dead branches which

may fall and strike the operator or helpers. Remove hazards before pruning.

 Plan retreat path from falling objects.

 Cut branches bounce when striking ground.

 Check that shoulder harness is adjusted for safe, comfortable operation.

 Turn the product off when moving from tree to tree.

 Avoid any contact with saw chain.

Failure to observe these precautions could cause serious injury.

 When transporting the unit, empty the fuel tank, install the guide bar cover, put the unit in an upright position, and

secure it firmly.

Failure to do so could result in damage or injury.

 Never attempt to operate the product with one hand.

 Ensure that you hook your thumbs around the grips, wrapping them in your

thumb and remaining fingers.

Kickback

 Kickback can lead to dangerous loss of control of the product and result in serious in-

jury to the operator or any one standing close by. Hold the product firmly with both

hands with thumbs and fingers encircling the front and rear handles. Be aware of the

down and outward path the pruner will take after the cut is made.

 Kickback may occur when the moving saw chain at the nose or tip of the guide bar touches

an object, or when the wood closes in and pinches the saw chain in the cut. In some cases

this may cause a lightning-fast reverse action, kicking the guide bar and saw chain up and

back or down and back towards the operator. Either of these reactions may cause the oper-

ator to lose control of the product which could result in serious personal injury.

 With a basic understanding of kickback, you can reduce or eliminate the element of surprise

which contributes to accidents.

 Avoid contact of the guide bar tip with any object while the saw chain is moving.

 Cut only wood. Avoid striking concrete, metal, wire, or other obstructions which could cause kickback or damage to the

saw chain.

 If the saw chain does strike a foreign object, immediately stop the engine, inspect and repair the product if necessary.

16

Pruning operation

Pruning techniques

 Plan cut carefully. Check direction branch will fall.

 Plan retreat path from falling branch. Cut branches bounce

when striking ground.

 Long branches should be removed in several pieces.

 Do not stand directly beneath branch being cut.

 When ready to cut: Hold "cutting shoe" against branch. This

will prevent whipping of the branch. Do not use back and forth

sawing action.

 Look out for branch immediately behind the branch being cut.

If saw chain hits rear branch damage to saw chain may occur.

 Accelerate to full throttle.

 Apply cutting pressure.

 Ease cutting pressure when nearing end of cut to maintain

control.

 When pruning a limb 102 mm diameter or larger cut as follows:

(1) Under cut 1/4 limb diameter near tree trunk.

(2) Finish top cut slightly farther out on limb.

(3) Flush cut stub at trunk.

 Do not use for felling or bucking.

 Check that the cutting attachment, guide bar, and saw chain is firmly attached and in safe operating condition.

 Use only one YAMABIKO-approved extension on the pruner.

 Do not hit rocks, stones, tree stumps, and other foreign objects with the saw chain.

 Do not cut into the ground with the saw chain.

 If cutting attachment end strikes an obstruction, stop engine immediately and inspect saw chain for damage.

 Do not operate with a dull, fractured, or discolored saw chain.

 Remove all foreign objects from work area.

 Always cover the guide bar and saw chain with guide bar cover during transportation and for storage.

 Operation of this equipment may create sparks that can start fires around dry vegetation. This product is equipped with a spark

arrestor and a spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating

to fire prevention requirements.

NOTE

 Use of Pruner may be subject to local regulations.

Guide against branch

Blade hits rear branch

17

Maintenance and care

Servicing guidelines

Maintenance and care

WARNING

Observe the following precautions when checking and maintaining your product after use:

 Turn the engine off and do not attempt to check or maintain the product until the engine has cooled.

You could burn yourself.

 Remove the spark plug cap before performing checks and maintenance.

An accident could occur if the product starts unexpectedly.

IMPORTANT

 Checking and maintenance requires specialist knowledge. If you are unable to check and maintain the product or deal with a

fault yourself, consult your dealer. Do not attempt to dismantle the product.

 For spare parts and consumables, please use only genuine parts and designated products and components. Using parts from

other manufacturers or non-designated components may result in a malfunction.

Area Maintenance Page Daily or be-

fore use

Every refuel 3 months or

90 hours

Yearly 600

hours

Air Filter Inspect/Clean 18 I / C * R *

Choke Shutter Inspect/Clean - I / C

Fuel Filter Inspect/Replace 18 I * I / R *

Fuel System Inspect/Replace 18 I * I*

Spark Plug Inspect/Clean/Replace 20 I/C/R *

Carburettor Adjust/Replace and adjust 18 I/R

Cooling System Inspect/Clean 19 I / C

Muffler Spark Arrestor Inspect/Clean/Replace 19 I/C/R *

Flexible shaft Inspect/Grease 20 I(1)

Guide Bar / Sprocket Nose Inspect/Clean/Lubricate 21 I / C * I

Saw Chain Inspect/Sharpen/Replace/

Tension

10/21 I * I *

Recoil Starter Rope Inspect/Clean - I / C *

Screws/Nuts/Bolts Inspect/Tighten/Replace - I *

Maintenance procedure letter codes: I= Inspect, R= Replace, C= Clean

(1) Apply good quality lithium grease every 25 hours of use.

* All recommendations to replace are based on the finding of damage or wear during inspection.

IMPORTANT

 Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance.

If you have any questions or problems, please contact your dealer.

18

Maintenance and care

Cleaning air filter

1. Close choke. Loosen air cleaner cover knob and remove air

cleaner cover (B).

2. Remove air filter (A) (air filter is located inside air cleaner

cover).

3. Brush dirt from filter or clean with compressed air from car-

burettor side.

4. Reinstall air filter with cover, after installing air filter to cover.

5. Tighten air cleaner cover knob.

Replacing fuel filter

1. Use a piece of metal wire or the like to pick up fuel filter (A)

through fuel tank opening.

2. Pull old filter from fuel line (B).

3. Install new fuel filter.

Carburettor adjustment

Every unit is test run at the factory and the carburettor is fine

tuned for maximum performance.

Before adjusting carburettor, clean or replace air filter, start en-

gine and run several minutes to bring it to operating temperature.

The engine must return to idle speed whenever the throttle lever

is released. Idle speed is adjustable, and must be set low enough

to permit the engine clutch to disengage the cutting attachment.

To adjust the carburettor proceed as follow:

1. Place the unit on the ground, then start the engine, and then

allow it to idle 2-3 minutes until warm.

2. If the attachment moves when the engine is at idle, reduce

the idle speed by turning the idle adjustment screw(T) coun-

ter-clockwise.

3. Repeat the process of accelerating to full throttle and return

to idle a few times. Check that the cutting attachment stops

moving at idle.

4. If a tachometer is available, the engine idle speed should be

final adjusted to the settings recommended in the Specifica-

tions section.

NOTE

 When reinstall air filter, fit it in the frame of the cleaner case.

NOTE

 If filter is excessive dirty or no longer fits properly, replace it.

WARNING

 YOU MAY ADJUST THE IDLE SPEED ONLY by turning the idle speed adjustment screw (T).

 During carburettor adjustment, the cutting attachment may move. Pay utmost attention and care to the cutting at-

tachment so as not to get injured by the moving cutter.

 When carburettor adjustment is completed, the cutting attachment should not move at idle speed, otherwise serious

personal injury may result.

 You must NOT carry out any Carburettor adjustment, other than the idle speed. All other adjustments MUST be per-

formed by an authorized service dealer, or serious personal injury may result due to malfunction of the engine.

CAUTION

 When there is trouble with the carburettor, contact an authorized service dealer.

La pagina si sta caricando...

Shindaiwa PT262S Manuale utente

Shindaiwa PT262S Manuale utente

in altre lingue

Documenti correlati

Altri documenti