Sharp LL-T1810A Manuale del proprietario

LCD MONITOR

LCD FARBMONITOR

MONITEUR LCD

MONITOR LCD

LL-T1810A

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUALE D’USO

Table of Contents / Inhaltsverzeichnis / Table des matières / Indice

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

2

3

Table of Contents

Notice for Users in the USA ............................................................................................................................ 4

TCO'99 ............................................................................................................................................................ 5

Notice for Users in Europe .............................................................................................................................. 7

Notice for Users in the UK ............................................................................................................................... 8

Notice for Users in Australia ............................................................................................................................ 8

Tips and safety precautions ............................................................................................................................ 9

Product description ....................................................................................................................................... 10

Connecting the monitor and turning the monitor on and off ........................................................................... 12

Connecting the monitor to a power source ............................................................................................... 12

Connecting the monitor to a computer (PC etc.) ....................................................................................... 13

Connecting to a second computer ............................................................................................................ 13

Connecting a USB device ......................................................................................................................... 13

Turning the power on ................................................................................................................................ 14

Changing between input terminals (INPUT 1

↔

2) ................................................................................ 14

Turning the power off ................................................................................................................................ 14

Adjusting the screen display .......................................................................................................................... 17

Automatic screen adjustment ................................................................................................................... 18

Adjusting the backlight .............................................................................................................................. 18

Manual screen adjustment........................................................................................................................ 19

Monitor care and repair ................................................................................................................................. 22

Monitor care ............................................................................................................................................. 22

Storage ..................................................................................................................................................... 22

Troubleshooting ........................................................................................................................................ 22

Specifications ................................................................................................................................................ 23

Instructions for attaching a VESA compliant arm .......................................................................................... 26

4

Notice for Users in the USA

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B

computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T1810A

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference re-

ceived, including interference that may cause undersized operation.

Responsible Party : SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL :1-800-BE-SHARP

* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal

of these materials may be regulated due to environmental considerations. For disposal or recycling

information, please contact your local authorities or the Electronics Industries Alliance:www.eiae.org

5

Congratulations!

You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a

product developed for professional use. Your purchase has also contributed to reducing the burden on the

environment and also to the further development of environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adapta-

tion of goods and services to the environment. The main problem, as far as computers and other electronics

equipment are concerned, is that environmentally harmful substances are used both in the products and

during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics

equipment, most of these potentially damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are important

from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of

electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emis-

sions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running

continuously and thereby consumes a lot of energy.

What does labelling involve?

This product meets the requirements for the TCO'99 scheme which provides for international and environ-

mental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO

(The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish

Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administra-

tion).

Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric

and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands impose restrictions on the presence and use of heavy metals, brominated and

chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must

be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be

adhered to in each country where the company implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain period of

inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to

reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction of

electric and magnetic fields, physical and visual ergonomics and good usability.

Below you will find a brief summary of the environmental requirements met by this product. The complete

environmental criteria document may be ordered from:

6

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): development@tco.se

Current information regarding TCO'99 approved and labelled products may also be

obtained via the Internet, using the address: http://www.tco-info.com/

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is

to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of

flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants

are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing

bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproduc-

tive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants

have been found in human blood and researchers fear that disturbances in foetus development may occur.

The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not

contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the

printed circuit boards since no substitutes are available.

Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer

displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 require-

ment states that batteries, the colour-generating layers of display screens and the electrical or electronics

components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in

high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also

demands that mercury is not present in any of the electrical or electronics components associated with the

labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light

system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing

this exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture

and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs

break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on

earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous

system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion

of lead since no replacement has yet been developed.

*

Bio-accumulative is defined as substances which accumulate within living organisms

**

Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

7

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by

93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit

Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées

par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla

direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ,

óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio

de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av

93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/

EEC.

CAUTION :

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION :

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT :

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN

ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DU SYSTEMS, DECONNECTEZ LA PRISE DE COURANT SECTEUR.

VARNING :

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION :

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

8

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code :

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows. The wire which is coloured GREEN-

AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the

safety earth or coloured green or green-and-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N

or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter

L or coloured red.

Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified

electrician.

"WARNING :THIS APPARATUS MUST BE EARTHED"

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

9

- Under certain display conditions, minute specks

or spots may be noticeable. This is common for

liquid crystal monitors and is not a malfunction.

- The LCD panel has been manufactured using

highly elaborate technology. Properly working

pixels comprise 99.99% of total pixels. However,

please understand that 0.01% or less of pixels

may be missing or be brighter than usual.

- Do not leave the screen displaying idly for long

periods of time, as this could cause afterimage to

remain.

- If the brightness is adjusted to the minimum set-

ting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using a

computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by

the customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be up-

graded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is

high, or where the monitor may come into

contact with oil or steam, as this could lead to

fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric

shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the

monitor to come into contact with strong shocks

or vibrations. Causing the monitor to fall or topple

over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating equipment

or anywhere else where there is likelihood of

high temperature, as this may lead to generation

of excessive heat and outbreak of fire

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or overly bend it. Also, do

not add extension cords. Damage to the cord

may result in fire or electric shock.

- Use only the AC adapter supplied with the

monitor. Using an AC adapter other than that

supplied may lead to fire.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating

Monitor and accessory checklist

- Please check that the following items are

included in the package.

- LCD monitor (1)

- AC adapter (1)

- USB cable (1)

- Monitor Settings Adjustment Disk for

Windows (1)

- Operation manual (1)

Notes:

- You are advised to retain the carton in case the

monitor needs to be transported.

- Authorship rights to the Monitor Settings

Adjustment Disk's program are held by Sharp

Corporation. Do not reproduce it without

permission.

Manual Scope

- In this booklet, Microsoft Windows 2000 will be

referred to as [Windows2000], Microsoft

Windows 98 as [Windows98], Microsoft Windows

95 as [Windows95], and Microsoft Windows

Version 3.1 as [Windows3.1]. When there is no

need to distinguish between programs, the term

[Windows] will be used.

- Microsoft and Windows are registered

trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

Tips and safety precautions

10

Product description

Front view

Control Panel

Power button (p. 14)

This button switches the monitor ON

and OFF.

Power LED (p. 14)

Green light: In use

Orange light: Power saving mode or

signal failure

Lamp off: Power OFF

buttons

SELECT button (p. 19)

This button is used to select menu options when the OSD Menu is

displayed.

MENU button (p. 19)

This button is used to pop-up, select and close the OSD Menu.

INPUT button (p. 14)

Use this button to switch between input signal terminals.

(INPUT 1

↔

INPUT 2)

When the On Screen Display (OSD) Menu is displayed:

These buttons are used to increase or decrease the value of a

selected option. (p. 19)

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness (p. 18).

11

Front view

Adjusting the angle of the monitor

Lightly holding both sides of the monitor, adjust it

to a suitable viewing angle.

Ventilation

openings

Note: Never block the ventilation

openings as this may lead to

overheating inside the monitor

and result in malfunction.

Power terminal (p. 12)

Remove the cover to see the power

terminal. The AC adapter is connected

here.

Ventilation

openings

INPUT 2 terminal and USB port

Remove the cover to view the computer

input terminal (INPUT 2) and USB port.

INPUT 2 terminal (p. 13)

A second computer can be connected

here.

USB port: Downstream (Port 2) (p. 13)

A USB device can be connected here.

USB port: Upstream (Port 1) (p. 13)

A USB-ready computer or self-powered

USB hub can be connected here.

RGB signal cable: INPUT 1 (p. 13)

This is to be connected to the computer's

(i.e. PC etc) analog RGB output terminal.

Security lock anchor

By connecting a security lock (purchased separately) to the security lock anchor, the

monitor is fixed so that it cannot be transported.

The theft prevention hole works in conjunction with Kensington Micro Saver Security

Systems.

Product description

12

(Rear View)

Stand cover

Lift one side

2. Remove the cover.

3. Connect the AC adapter to the monitor's power

terminal.

4. Replace cover.

Cover

Place cord

on hook

AC adapter

Run cord

through hole.

Power terminal

Cover

5. Connect power cord to AC adapter.

Fitting the AC adapter inside the stand

Wind the cord

Place adapter

inside stand cavity.

6. Replace stand cover.

Stand cover

7. Place power plug into AC outlet.

Connecting the monitor to a power source

Use only the AC adapter supplied.

1. Remove the stand cover.

Connecting the monitor and turning

the monitor on and off

Power cord

13

Connecting the monitor and turning the monitor on and off

RGB cable

If connecting to a D-sub 15 pin 2 row Apple

Power Macintosh, attach a Macintosh conver-

sion adapter (to be purchased separately) to

the RGB signal cable.

Macintosh conversion adapter

RGB signal cable

After connecting the adapter, tighten the

screws on each side to fix into place.

Firmly insert the analog RGB output

terminal (mini D-sub 15 pin with 3 rows)

then tighten the screws each side.

Note:

- If connecting to the Sun Ultra series, a conversion

adapter (purchased separately) may be

required.

(Rear View)

Cover

(Rear View)

Cover

2. Connect the RGB signal cable (purchased

separately) to the INPUT 2 terminal.

INPUT 2 terminal

RGB signal cable

(purchased sepa-

rately)

To the computer's

RGB output terminal

Connecting the monitor to a computer

(PC etc.)

When connecting, ensure that both the monitor and

computer are switched off.

Connecting to a second computer

A RGB signal cable (to be purchased separately) is

needed to connect a second computer.

1. Remove the cover

3. Replace the cover.

Connecting a USB device

This monitor can be used with hubs which use the

USB standard (Rev. 1.1).

Downstream (2 ports)

USB devices such as keyboard and mouse can be

connected here. Up to 100mA of power is able to be

supplied per port. Devices requiring more than

100mA cannot be connected.

Upstream (1 port)

USB compatible computers and self-powered hubs

can be connected. (Bus-powered hubs cannot be

connected.)

Notes:

- If a USB cable is required, please use the one

included.

- Before connecting, ensure that the shape of the

USB cable connector is correct.

- For information regarding the USB function (such

as set-up) please refer to the operation manual of

the computer to be connected.

- Some devices may not be able to be activated.

To ascertain a certain device's USB

compatibility, please contact the manufacturer of

the device.

1. Remove the cover.

14

Connecting the monitor and turning the monitor on and off

2. Connect the USB cable.

3. Replace the cover.

Turning the power on

When connecting, ensure that both the monitor and

computer are switched off.

Turn monitor on

Turn on device to

which monitor is

connected

The power LED

Notes:

- Depending on the computer or OS, it may be

necessary to use the computer to install monitor

set-up information. If so, follow the steps below to

install the monitor set-up information. (p. 15)

- When setting up the monitor or a connected

computer for the first time, connecting an

additional computer or after having changed an

aspect of the current system, perform an

automatic screen adjustment before use (p. 18).

Power LED

Green light: In use

Orange light: Power saving mode or signal

failure

Lamp off: Power OFF

Press power button

USB port: Downstream (2 ports)

USB port: Upstream (1 port)

INPUT button

Pushing this button switches between input

signal terminals, so that the screen changes

to display any of the machines connected.

Turning the power off

Turn off device

to which monitor

is connected

Press power button

Turn monitor off

CAUTION!

Do not leave the monitor in contact with rubber or

plastic items for long periods of time as this could

lead to color change or change in shape.

Changing between input terminals

(INPUT 1

↔ ↔

↔

2)

When connected to two computers, use the INPUT

button to switch between input signal terminals (i.e.

to choose which computer's screen you want dis-

played.)

15

Connecting the monitor and turning the monitor on and off

Installing set-up information and the ICC

profile

Depending on the computer or OS, it may be neces-

sary to use the computer to operate the installation

of monitor set-up information etc. If so, follow the

steps below to install the monitor set-up information.

(Depending on the computer type, command names

and methods may differ. Please follow the compu-

ter’s own operation manual while reading this.)

Note:

This explanation assumes that the floppy disk drive

is "A drive". If the floppy disk drive of your computer

is not "A drive", please read the below substituting

the floppy disk drive you are using in place of "A

drive" or "A".

7. Check that the monitor details are displayed,

then click [Apply].

8. Click [OK], and close the window.

9. Remove the Monitor Settings Adjustment

Disk from the A drive

For Windows98

Installing monitor set-up information into Windows

98, and setting the monitor's ICC profile as a prede-

termined value.

This explanation assumes that the floppy disk drive

is "A drive".

If the "Add New Hardware Wizard" has appeared:

1. Place the Monitor Settings Adjustment Disk

(provided) into the computer's A drive.

2. Click [Next].

3. Check [Display a list of all the drivers in a specific

location, so you can select the driver you want.],

then click [Next].

4. When [Models] is displayed, click on [Have Disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

5. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish]. If the "Add

New Hardware Wizard" appears, repeat the

installation commands beginning from 2 above.

6. Remove the Monitor Settings Adjustment Disk

from the A drive.

If the "Add New Hardware Wizard" has not ap-

peared:

1. Place the Monitor Settings Adjustment Disk in the

computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Click [Next].

7. Click on [Display a list of all the drivers in a

specific location, so you can select the driver you

want.], then click [Next].

About ICC profiles

An ICC (International Color Consortium) profile

is a file that describes the color characteristics of

the LCD monitor. By using an application that

works together with an ICC profile, a high color

resolution can be realized.

Notes:

- Both Windows 98 and Windows 2000 use the

ICC profile.

- When the storing Windows 98 and Windows

2000 set-up information, the ICC profile is also

installed. If you would like to install the ICC

profile only, please refer to Installing the ICC

profile on the following page.

- When using the ICC profile, please set the

[WHITE BALANCE] to [STD].

Installing set-up information

For Windows 95

Installing monitor set-up information into Windows 95.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Monitor Settings Adjustment Disk

(provided) into the computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have Disk], confirm that [Copy

manufacturer's files from:] is [A:] then click [OK].

6. Confirm that the monitor details are selected, and

click [OK].

16

Connecting the monitor and turning the monitor on and off

8. When [Models] is displayed, click on [Have Disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

9. Confirm that the monitor details are selected, then

click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.

12. Remove the Monitor Settings Adjustment Disk

from the A drive.

For Windows2000

Installing monitor set-up information into Windows

2000, and setting the monitor's ICC profile as a

predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Monitor Settings Adjustment Disk

(provided) into the computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. Click on [Properties], [Driver] and [Update

Driver].

6. When [Upgrade Device Driver Wizard] appears,

click [Next].

7. Check [Display a list of the known drivers for this

device so that I can choose a specific driver] and

click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

9. Select the monitor from the list displayed and

click [Next].

10.Click [Next], confirm that the monitor's name

appears on the screen, and click [Finish]. If

[Digital Signature Not Found] appears, click [Yes].

11.Click on [Close].

12.Click [OK], and close the window.

13.Remove the Monitor Settings Adjustment Disk

from the A drive.

Installing the ICC profile

Installing the monitor’s ICC profile. (If the set-up

information has already been installed, so too has

the profile, and there is no need to install it.)

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Monitor Settings Adjustment Disk in the

computer’s A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings] and [Advanced].

5. Click on [General] and from [Compatibility] select

[Apply the new display settings without

restarting], then click on [Color Management].

6. Click [Add], and select [3 ½ Floppy [A:]] as the

file location.

7. Choose the color profile that you would like to

install, and click on [Add].

8. Choose the profile and click on [Set As Default].

9. Click [OK], and close the window.

10.Remove the Monitor Settings Adjustment Disk

from the A drive.

When using the ICC profile, please set the [WHITE

BALANCE] to [STD].

17

If necessary, the screen can be adjusted as follows.

Automatic screen adjustment (p. 18)

The CLOCK, PHASE, H-POS (horizontal position-

ing) and V-POS (vertical positioning) functions can

be adjusted automatically.

Adjustment of backlight (p. 18)

Brightness of backlight can be adjusted.

Manual adjustment (p. 19)

Fine adjustments can be made using the On Screen

Display (OSD) Menu.

Note:

- All adjustments will be saved even after turning

the power off.

Useful functions and tips

Resetting MENU 1 (ADJUSTMENT)

MENU 1 (ADJUSTMENT) values can be returned to

their original ex-factory values in one command.

1. Turn on the monitor power.

2. Press the MENU button and the

button

simultaneously. When [RESET] appears on the

screen, the reset is complete.

Resetting all adjustment values

All adjustment values can be returned to their

original ex-factory values in one command.

1. Turn off the monitor power.

2. Press the MENU button and the SELECT button

simultaneously, and while doing this press the

power button (i.e. turn the power on). When [ALL

RESET] appears on the screen, the reset is

complete.

Note:

- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

Adjustment lock function

By disabling the control buttons (i.e. setting the lock)

any attempted changes to adjusted values will be

voided.

1. Turn off the monitor power.

2. While pressing the MENU button, press the

power button (i.e. turn the power on). This will set

the lock. (When this appears on the screen, the

lock is in place.)

Removing the lock

If the lock is in place and the above-mentioned

command is repeated, the lock will be removed.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Choosing a message language

Messages displayed on the screen and OSD Menu

contents can be changed to the following languages.

Dutch, English, French, German, Spanish, Italian,

Swedish.

1. Turn off the monitor.

2. Pressing the

and buttons simultaneously,

press the power button (i.e. turn the power on).

The Language Selection Menu (LANGUAGE) will

be displayed on the screen.

3. Use the SELECT button to choose a language.

4. Press the MENU button.

The setting is complete. From now, messages

and adjustment menus will be displayed in the

chosen language.

Adjusting the screen display

18

Adjusting the screen display

Adjustment pattern

Automatic screen adjustment

Options in MENU 1 (ADJUSTMENT) can be ad-

justed automatically (CLOCK, PHASE, H-POS, V-

POS).

Note:

- When setting up the monitor or a connected

computer for the first time, connecting an

additional computer or after having changed an

aspect of the current system, perform an

automatic screen adjustment before use

Automatic adjustment screen display

To perform an automatic adjustment, first display an

image that makes the entire screen very bright. If

you are using Windows, you can also use the

Adjustment Pattern on the accompanying Monitor

Settings Adjustment Disk for Windows.

Displaying the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000, and

assumes that the floppy disk drive is [A drive].

Note:

- If the floppy disk drive of your computer is not

"A drive", please read the below substituting the

floppy disk drive you are using in place of

"A drive" or "A".

1. Place the Monitor Settings Adjustment Disk

(provided) into the computer's A drive.

2. Open [My Computer] and select [3 ½ Floppy

(A:)]. If using Windows 3.1, open [File Manager]

and choose "A drive".

3. Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern will

appear.

Notes:

- After completing the adjustment, press the

computer's [Esc] key to exit the Adjustment

Program.

- If your computer's display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the input signal

specification and is not a malfunction.)

Adjusting the screen automatically

1. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

2. Press the

button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3. Press the MENU button 4 times to make the On

Screen Display (OSD) Menu disappear.

Notes:

- In most cases the monitor is ready to be used

after automatic adjustment.

- If necessary due to any of the following, manual

adjustments (p. 19) can be made after the

automatic adjustment.

- When further fine adjustment is needed.

- When the computer's video input signals are

Composite Sync or Sync On Green.

(Automatic adjustments may not be

possible.)

- When, after command 2 above, [OUT OF

ADJUST] is displayed. (When the screen

displays an entirely dark image, the

automatic screen adjustment may be

disabled. When making an automatic

adjustment, be sure to either use the

Adjustment Pattern or try displaying an image

that makes the entire screen very bright.)

Adjusting the backlight

The backlight brightness can be adjusted.

Carry out the commands without the On Screen

Display (OSD) Menu displayed. If the OSD Menu is

displayed, press the MENU button (several times

may be required) and begin when the OSD Menu

has disappeared.

1. Without the OSD Menu being displayed, push the

or the button. At the bottom of the screen the

BRIGHT bar will appear.

2. Adjust by pressing the button (darker) or

button (lighter).

The BRIGHT bar automatically disappears approxi-

mately 3 seconds after the last command.

19

Adjusting the screen display

Horizontal flicker noise

Vertical flicker noise

Screen frame

MENU 1: ADJUSTMENT

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted

Notes:

- Press the

button to select AUTO.

- To choose a menu option: SELECT button

- To go to MENU 2: MENU button

CLOCK

The figure below demonstrates how to adjust so that

vertical flicker noise is not emitted. (

buttons)

PHASE

The figure below demonstrates how to adjust so that

horizontal flicker noise is not emitted. (

buttons)

Note:

- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS

(vertical positioning)

To center the screen image within the boundaries of

the screen, adjust the left-right (H-POS) values and

the up-down (V-POS) values. (

buttons)

Manual screen adjustment

Fine adjustments can be made using the On Screen

Display (OSD) Menu provided.

MENU 1: ADJUSTMENT

CLOCK, PHASE, H-POS (horizontal

positioning) and V-POS (vertical

positioning)

MENU 2: GAIN CONTROL

BRIGHT (brightness), CONT (contrast)

MENU 3: WHITE BALANCE

R-CONT (blue-green to red), G-CONT

(purple to green), B-CONT (yellow to blue)

MENU 4: MODE SELECT

INPUT (input mode), 400LINE (resolution),

EXPAND (screen expansion), LEVEL (level

of scaling)

The screen display during adjustment

If using Windows, the Adjustment Pattern on the

accompanying Monitor Settings Adjustment Disk for

Windows can be used. (p. 18)

If using a computer other than Windows, the adjust-

ment pattern cannot be used. Display an image that

makes the entire screen very bright, and adjust

while watching the screen.

Note:

- This explanation is based on using the Adjust-

ment Pattern (for Windows) to make adjustments.

Adjusting

1. Press the MENU button. The ADJUSTMENT

Menu will be displayed.

At this point relevant menu options can be adjusted.

Each time the MENU button is pressed, the next

menu is selected. (MENU 1 → 2 → 3 → 4 → OSD

Menu disappears)

Note:

- The OSD Menu automatically disappears

approximately 20 seconds after the last com-

mand.

20

Adjusting the screen display

MENU 2: GAIN CONTROL

BRIGHT (brightness) and CONT (contrast) are

optimized before shipment, but depending on the

type of computer being used, further adjustment

may be necessary.

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted using the Auto Gain Control*

function,

Notes:

- Press the

button to select AUTO.

- To choose a menu option: SELECT button

- To go to MENU 3: MENU button

*Auto Gain Control function

The Auto Gain Control adjusts contrast and

brightness based on the brightest color of the

image displayed. If you are not using the

Adjustment Pattern it is necessary to have an

area of at least 5 mm x 5 mm of white image

displayed, and if not adjustments may not be

possible. (In such case, [OUT OF ADJUST] will

appear and setting values remain unchanged.)

BRIGHT (brightness)

Total screen brightness can be adjusted while

watching the color pattern. (

buttons)

CONT (Contrast)

While watching the color pattern, adjustments can be

made so that all graduations appear. (

buttons)

Color pattern

MENU 3: WHITE BALANCE

WHITE BALANCE can be adjusted as necessary.

(As adjustments are made before shipment, there is

no real necessity for further alteration.)

Notes:

- Not all graduations for COOL and WARM can be

displayed. To display all graduations, set to

STD.

- Selecting USER will display the setting values for

R-CONT, G-CONT and B-CONT, enabling fine

adjustments.

- To choose a menu option: SELECT button

- To go to MENU 4: MENU button

COOL . . . Color tone bluer than standard

- . . . . . . Color tone slightly bluer than standard

STD . . . . . Color tone standard setting

- . . . . . . Color tone slightly redder than standard

WARM . . . Color tone redder than standard

USER

R-CONT . . . . . . .

button for blue-green

button for red

G-CONT . . . . . . .

button for purple

button for green

B-CONT . . . . . . .

button for yellow

button for blue

La pagina sta caricando ...

Sharp LL-T1810A Manuale del proprietario

Sharp LL-T1810A Manuale del proprietario

in altre lingue

Documenti correlati