Sharp Computer Monitor LL-T15G1 Manuale utente

LCD MONITOR

LCD FARBMONITOR

MONITEUR LCD

MONITOR LCD

 !"==== !=EiiJqNRdNF

iiJqNRdN

iiJbNRdN

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EPLOI

MANUALE D’USO

MANUAL DE FUNCIONAMIENTO

 !"

Table of Contents / Inhaltsverzeichnis / Table des matières / Indice / Índice / 

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

2

3

English

Table of Contents

Notice for Users in the USA ............................................................................................................................ 4

TCO'99 (LL-T15G1) ........................................................................................................................................ 5

Notice for Users in Europe (LL-T15G1) ........................................................................................................... 7

Notice for Users in the UK ............................................................................................................................... 8

Notice for Users in Australia ............................................................................................................................ 8

Tips and safety precautions ............................................................................................................................ 9

Product description ....................................................................................................................................... 10

Standing up and adjusting the monitor ..................................................................................................... 11

Connecting the monitor and turning the monitor on and off ........................................................................... 12

Connecting the monitor to a computer (PC etc.) ....................................................................................... 12

Connecting the monitor to a power source ............................................................................................... 12

Turning the power on ................................................................................................................................ 12

Turning the power off ................................................................................................................................ 13

Installing set-up information and the ICC profile (for Windows) .................................................................13

Information about the ColorSync profile (for MacOS) ............................................................................... 16

Adjusting the screen display .......................................................................................................................... 17

Adjusting the backlight .............................................................................................................................. 17

Automatic screen adjustment ................................................................................................................... 18

Manual screen adjustment........................................................................................................................ 19

Monitor care and repair ................................................................................................................................. 22

Monitor care ............................................................................................................................................. 22

Storage ..................................................................................................................................................... 22

Troubleshooting ........................................................................................................................................ 22

Specifications ................................................................................................................................................ 23

Instructions for attaching a VESA compliant arm .......................................................................................... 26

4

Notice for Users in the USA

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B

computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T15G1 / LL-E15G1

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference re-

ceived, including interference that may cause undersized operation.

Responsible Party : SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL :1-800-BE-SHARP

* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal

of these materials may be regulated due to environmental considerations. For disposal or recycling

information, please contact your local authorities or the Electronics Industries Alliance:www.eiae.org

5

English

Congratulations!

You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a

product developed for professional use. Your purchase has also contributed to reducing the burden on the

environment and also to the further development of environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adapta-

tion of goods and services to the environment. The main problem, as far as computers and other electronics

equipment are concerned, is that environmentally harmful substances are used both in the products and

during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics

equipment, most of these potentially damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are important

from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of

electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emis-

sions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running

continuously and thereby consumes a lot of energy.

What does labelling involve?

This product meets the requirements for the TCO'99 scheme which provides for international and environ-

mental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO

(The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish

Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administra-

tion).

Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric

and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands impose restrictions on the presence and use of heavy metals, brominated and

chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must

be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be

adhered to in each country where the company implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain period of inac-

tivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reacti-

vate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction of

electric and magnetic fields, physical and visual ergonomics and good usability.

Below you will find a brief summary of the environmental requirements met by this product. The complete

environmental criteria document may be ordered from:

LL-T15G1

6

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): development@tco.se

Current information regarding TCO'99 approved and labelled products may also be

obtained via the Internet, using the address: http://www.tco-info.com/

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is

to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of

flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants

are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing

bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproduc-

tive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants

have been found in human blood and researchers fear that disturbances in foetus development may occur.

The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not

contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the

printed circuit boards since no substitutes are available.

Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer

displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 require-

ment states that batteries, the colour-generating layers of display screens and the electrical or electronics

components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in

high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also

demands that mercury is not present in any of the electrical or electronics components associated with the

labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light

system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing

this exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture

and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs

break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on

earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous

system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion

of lead since no replacement has yet been developed.

*

Bio-accumulative is defined as substances which accumulate within living organisms

**

Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

7

English

Notice for Users in Europe (LL-T15G1)

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by

93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit

Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées

par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla

direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ,

óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio

de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av

93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/

EEC.

CAUTION :

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION :

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT :

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN

ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L’APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING :

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION :

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

8

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code :

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows. The wire which is coloured GREEN-

AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the

safety earth or coloured green or green-and-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N

or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter

L or coloured red.

Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified

electrician.

"WARNING :THIS APPARATUS MUST BE EARTHED"

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

9

English

- The TFT color LCD panel used in this monitor is

made with the application of high precision

technology. However, there may be minute points

on the screen where pixels never light or are

permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or

brightness. Please note that these are not

malfunctions but common phenomena of LCDs

and will not affect the performance of the monitor.

- Do not leave the screen displaying idly for long

periods of time, as this could cause afterimage to

remain.

- If the brightness is adjusted to the minimum setting

it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using a

computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by the

customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be upgraded

without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is high,

or where the monitor may come into contact with

oil or steam, as this could lead to fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric shock.

- Do not place the monitor on top of unstable objects

or in unsafe places. Do not allow the monitor to

come into contact with strong shocks or vibrations.

Causing the monitor to fall or topple over may

damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating equipment

or anywhere else where there is likelihood of high

temperature, as this may lead to generation of

excessive heat and outbreak of fire.

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or overly bend it. Also, do

not add extension cords. Damage to the cord may

result in fire or electric shock.

- Use only the AC adapter supplied with the monitor.

Using an AC adapter other than that supplied may

lead to fire.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating.

Monitor and accessory checklist

- Please check that the following items are included

in the package.

- LCD monitor (1)

- AC adapter (1)

(model name: NL-A60J , color: gray)

- RGB signal cable (1)

- Utility Disk (For Windows/Macintosh) (1)

- Operation manual (1)

Notes:

- You are advised to retain the carton in case the

monitor needs to be transported.

- Sharp Corporation holds authorship rights to the

Utility Disk program. Do not reproduce it without

permission.

Use of AC adapter

- Do not use the AC adapter for other than the

specified equipment.

- Unplug the AC adapter if it is not used for long

time.

- Do not place any objects on the AC adapter.

- Do not use the AC adapter outdoors.

- Do not attempt to repair the AC adapter if it is

broken or malfunctioning. Refer the servicing to the

service representative.

- Do not try to open the AC adapter.

- Do not use water or wet cloth for cleaning the AC

adapter.

Manual Scope

- In this booklet, Microsoft Windows XP will be

referred to as [WindowsXP], Microsoft Windows

Millenium as [WindowsMe], Microsoft Windows

2000 as [Windows2000], Microsoft Windows 98 as

[Windows98], Microsoft Windows 95 as

[Windows95], and Microsoft Windows Version 3.1

as [Windows3.1]. When there is no need to

distinguish between programs, the term [Windows]

will be used.

- Microsoft and Windows are registered trademarks

of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

Tips and safety precautions

10

Product description

1. MENU button This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

2. SELECT button This button is used to select menu options when the OSD Menu is

displayed.

3.

buttons When the OSD Menu is displayed:

These buttons are used to increase or decrease the value of a selected

option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness .

4. Power LED This LED is lit green when in use and orange when in power-saving

mode.

5. Power button Pressing this button turns the power on. (After turning the power on, it

may take a little time before the screen displays.)

Press the button again to turn the power off.

6. Power terminal The AC adapter is connected here.

7. RGB input terminal The RGB signal cable is connected here.

8. Security lock anchor By connecting a security lock (purchased separately) to the security lock

anchor, the monitor is fixed so that it cannot be transported.

The security slot works in conjunction with Kensington Micro Saver

Security Systems.

9. Ventilation openings Note: Never block the ventilation openings as this may lead to overheat-

ing inside the monitor and result in malfunction.

MENU SELECT

1

2

3

45

67 8

9

Control Panel

11

English

Product description

Standing up and adjusting the monitor

CAUTION!

- Pressure from hands on the LCD panel could

cause damage.

Standing up the monitor

Press down on the stand and lift up the top section

of the monitor.

- Be careful not to pinch your fingers.

- When raising the display section, movement

becomes harder in the middle of travel. Continue

raising by applying more force at that point.

- When the monitor is used with an arm mounting,

movement becomes stiffer to keep the display

section from tipping over. This is not a

malfunction.

Adjusting the monitor

Press down on the stand and adjust it to a suitable

viewing angle.

Folding up the monitor

1. Remove the AC adapter and the RGB signal

cable.

2. Press down on the stand and gently fold back the

monitor.

- Be careful not to pinch your fingers.

- Do not use the monitor when tilted back beyond

approximately 25º.The monitor may fall over

leading to injury or malfunction.

approx.25°

approx.5°

Prohibited range

approx.25°

approx.5°

12

Connecting the monitor and turning

the monitor on and off

Connecting the monitor to a computer

(PC etc.)

When connecting, ensure that both the monitor and

computer are switched off.

Note:

- Do not overly bend the cable or add extension

cords as this could lead to malfunction.

Firmly insert the analog RGB terminal

(mini D-sub 15 pin with 3 rows) then

tighten the screws each side.

RGB signal cable

If connecting to a D-sub 15 pin 2 row Apple

Power Macintosh, attach a Macintosh conver-

sion adapter (to be purchased separately) to

the RGB signal cable.

Macintosh conversion adapter

RGB signal cable

After connecting the adapter, tighten the

screws on each side to fix into place.

Connecting the monitor to a power source

Before connecting, first turn off the monitor's main

power switch.

Note:

- Do not overly bend the cable or add extension

cords as this could lead to malfunction.

1. Connect the AC adapter to the monitor's power

terminal.

2. Attach the power cord to the AC adapter and

place the power plug into the AC terminal.

Power terminal

AC adapter

Turning the power on

1. Press the monitor's power button.

2. Turn on the computer.

The power LED will be lit green, and the screen

will display an image.

Power cord

AC terminal

ON

Turn on device to

which monitor is

connected

Press power button

13

English

Connecting the monitor and turning the monitor on and off

Turning the power off

1. Turn the computer off.

2. Press the monitor's power button.

The Power LED will disappear.

If the monitor is not going to be used for a long

period of time, be sure to unplug it from the AC

outlet.

Installing set-up information and the ICC

profile (for Windows)

Depending on the computer or OS, it may be neces-

sary to use the computer to operate the installation

of monitor set-up information etc. If so, follow the

steps below to install the monitor set-up information.

(Depending on the type of computer or OS, com-

mand names and methods may differ. Please follow

the computer’s own operation manual while reading

this.)

About the ICC profile

An ICC (International Color Consortium) profile is

a file that describes the color characteristics of

the LCD monitor. By using an application that

works together with an ICC profile, a high color

resolution can be realized.

- Windows98/2000/Me/XP all use the ICC

profile.

- When installing Windows98/2000/Me/XP set-

up information (described below), the ICC

profile is also installed. If you would like to

install the ICC program only, please refer to

Installing the ICC profile on page 15.

- When using the ICC profile, please set the

[WHITE BALANCE] to [STD] .

Installing set-up information

For Windows95

Installing monitor set-up information into Windows95.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk (provided) into the compu-

ter's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy manufac-

turer's files from:] is [A:] then click [OK].

6. Confirm that the monitor details are selected, and

click [OK].

7. Check that the monitor details are displayed, then

click [Apply].

8. Click [OK], and close the window.

9. Remove the Utility Disk from the A drive.

Note:

- If using the monitor for the first time or after

having changed the system settings during use,

perform an automatic screen adjustment.

- Depending on the computer or OS, it may be

necessary to use the computer to install monitor

set-up information. If so, follow the steps below to

install the monitor set-up information.

OFF

Turn off device

to which monitor

is connected

Press power button

14

Connecting the monitor and turning the monitor on and off

For Windows98

Installing monitor set-up information into Win-

dows98, and setting the monitor's ICC profile as a

predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

If the "Add new Hardware Wizard" has appeared:

1. Place the Utility Disk (provided) into the compu-

ter's A drive.

2. Click [Next].

3. Check [Display a list of all the drivers in a specific

location, so you can select the driver you want.],

then click [Next].

4. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

5. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish]. If the "Add

New Hardware Wizard" appears, repeat the

installation commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not ap-

peared:

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Click [Next].

7. Click on [Display a list of all the drivers in a

specific location, so you can select the driver you

want.], then click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

9. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish].

10.Check that the monitor details are displayed, then

click [Apply].

11.Click [OK], and close the window.

12.Remove the Utility Disk from the A drive.

For Windows2000

Installing monitor set-up information into Win-

dows2000, and setting the monitor's ICC profile as a

predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk (provided) into the compu-

ter's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. Click on [Properties], [Driver] and [Update

Driver].

6. When [Upgrade Device Driver Wizard] appears,

click [Next].

7. Check [Display a list of the known drivers for this

device so that I can choose a specific driver] and

click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

9. Select the monitor from the list displayed and

click [Next].

10.Click [Next], confirm that the monitor's name

appears on the screen, and click [Finish]. If [The

Digital Signature Not Found] appears, click [Yes].

11.Click on [Close].

12.Click [OK], and close the window.

13.Remove the Utility Disk from the A drive.

For WindowsMe

Installing monitor set-up information into

WindowsMe, and setting the monitor's ICC profile as

a predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

If the "Add new Hardware Wizard" has appeared:

1. Place the Utility Disk (provided) into the compu-

ter's A drive.

2. Check [Specify the location of the driver [Ad-

vanced]] and click [Next].

3. Check [Display a list of all the drivers in a specific

location, so you can select the driver you want.],

then click [Next].

4. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

15

English

Connecting the monitor and turning the monitor on and off

5. Select the monitor details from the list, then click

[Next], [Next], and [Finish]. If the "Add new

Hardware Wizard" appears, repeat the installa-

tion commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not ap-

peared:

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Check [Specify the location of the driver

[Advanced]] and click [Next].

7. Check [Display a list of all the drivers in a specific

location, so you can select the driver you want.]

and click [Next].

8. When [Models] is displayed, click on [Have disk],

confirm that [Copy manufacturer's files from:] is

[A:], and click [OK].

9. Select the monitor details, then click [Next],

[Next], and [Finish].

10.Check that the monitor details are displayed, then

click [Apply].

11.Click [OK], and close the window.

12.Remove the Utility Disk from the A drive.

For WindowsXP

Installing monitor set-up information into

WindowsXP, and setting the monitor's ICC profile as

a predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. Choose [Control

Panel].

3. Switch to "Classic View".

4. Double click on [Display].

5. Click on [Settings], [Advanced] and [Monitor].

6. Click on [Properties], [Driver] and [Update

Driver].

7. When [Hardware Update Wizard] appears, check

[Install from a list or specific location [Advanced]]

and click [Next].

8. Check [Don't search. I will choose the driver to

install.] and click [Next].

9. Click on [Have Disk], confirm that [Copy

manufacturer's files from:] is [A:], and click [OK].

10.Select the monitor from the list displayed and

click [Next].

If [has not passed Windows Logo testing...]

appears, click [Continue Anyway].

11.Confirm that the monitor's name appears on the

screen.

12.Click on [Finish].

13.Click on [Close].

14.Click [OK], and close the window.

15.Remove the Utility Disk from the A drive.

Installing the ICC profile

Installing the monitor’s ICC profile. (If the set-up

information has already been installed, so too has

the profile, and there is no need to install it.)

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk in the computer’s A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings] and [Advanced].

5. Click on [General] and from [Compatibility] select

[Apply the new display setting without restarting],

then click on [Color Management].

6. Click [Add], and select [3 ½ Floppy [A:]] as the

file location.

7. Choose the color profile that you would like to

install, and click on [Add].

8. Choose the profile and click on [Set As Default].

9. Click [OK], and close the window.

10.Remove the Utility Disk from the A drive.

- When using the ICC profile, please set the

[WHITE BALANCE] to [STD].

16

Information about the ColorSync profile

(for MacOS)

About the ColorSync profile

ColorSync is the Apple Corporation's color man-

agement system and is a function that enables

color resolution to be realized when used with a

compatible application. A ColorSync profile

describes the color characteristics of the LCD

monitor.

Notes:

- This monitor's ColorSync profile works with

MacOS8.5 or above.

- When using the ColorSync profile, please set

the [WHITE BALANCE] to [STD] .

Setting up the ColorSync profile

Notes:

- A floppy disk drive is necessary. In addition, it is

necessary to have PC Exchange or File

Exchange installed in your system.

- Depending on the type of computer or OS,

command names and methods may differ. Please

follow the computer’s own operation manual while

reading this.

1. Place the Utility Disk (provided) into the

computer’s floppy disk drive.

2. Copy the profile to be used from the Mac folder

on the Utility Disk to the ColorSync profile folder

located within the system folder.

3. Using the ColorSync on the control panel,

choose the profile to be used.

Connecting the monitor and turning the monitor on and off

17

English

Adjusting the screen display

Adjustment the backlight (right column)

Brightness of backlight can be adjusted.

Automatic screen adjustment (p.18)

The CLOCK, PHASE, H-POS (horizontal position-

ing) and V-POS (vertical positioning) functions can

be adjusted automatically.

Manual screen adjustment (p. 19)

Fine adjustments can be made using the On Screen

Display (OSD) Menu.

Note:

- All adjustments will be saved even after turning

the power off.

Resetting all adjustment values

All adjustment values can be returned to their

original ex-factory values in one command.

1. Turn off the monitor power.

2. Press the MENU button and the SELECT button

simultaneously, and while doing this press the

power button (i.e. turn the power on). When [ALL

RESET] appears on the screen, the reset is

complete.

3. Turn off the monitor power.

Note:

- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

ADJUSTMENT menu reset

The adjustment values of the analogue signal time’s

ADJUSTMENT menu can be returned to their

original ex-factory values.

1. Turn on the monitor power.

2. Press the MENU button and the

button

simultaneously. When [RESET] appears on the

screen, the reset is complete.

Adjustment lock function

By disabling the control buttons (i.e. setting the lock)

any attempted changes to adjusted values will be

voided.

1. Turn off the monitor power.

2. While pressing the MENU button, press the

power button (i.e. turn the power on).

Continue to press the button until the message

appears on the screen.

When the menu is unlocked:

[ADJUSTMENT LOCKED] will appear on

the screen, and the lock will be set.

When the menu is locked:

[ADJUSTMENT UNLOCKED] will appear

on the screen, and the lock will be

removed.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Adjusting the backlight

1. Without the OSD Menu being displayed, press

the

button or the button.

2. Adjust by pressing the

button (darker) or the

button (lighter).

The BRIGHT bar automatically disappears

several seconds after the last command.

BRIGHT 31

18

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be adjusted

automatically (CLOCK, PHASE, H-POS V-POS).

Note:

- When setting up this monitor for the first time or

after having changed an aspect of the current

system, perform an automatic screen adjustment

before use.

Automatic adjustment screen display

To perform an automatic adjustment, first display an

image that makes the entire screen very bright. If

you are using Windows, you can also use the

Adjustment Pattern on the accompanying Utility Disk

for Windows.

Displaying the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000/Me/XP,

and assumes that the floppy disk drive is [A drive].

Note:

- If the floppy disk drive of your computer is not

"A drive", please read the below substituting the

floppy disk drive you are using in place of

"A drive" or "A".

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Open [My Computer] and select [3 ½ Floppy

(A:)]. If using Windows 3.1, open [File Manager]

and choose "A drive".

3. Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern will

appear.

Adjustment pattern

After completing the adjustment, press the

computer's [Esc] key to exit the Adjustment

Program.

Notes:

- If your computer's display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the input signal

specification and is not a malfunction.)

Adjusting the screen automatically

1. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK

127

PHASE 16

H

-

POS

200

V

-

POS 29

1024X768

V:75Hz H:60.0kHz

2. Press the button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3. Press the MENU button 4 times to make the On

Screen Display (OSD) Menu disappear.

Notes:

- In most cases automatic adjustment is sufficient.

- If necessary due to any of the following, manual

adjustments (p. 19) can be performed after the

automatic adjustment.

- When further fine adjustment is needed.

- When the computer’s video input signals are

Composite Sync or Sync On Green.

(Automatic adjustments may not be possible.)

- When [OUT OF ADJUST] is displayed.

(When the screen displays an entirely dark

image, the automatic screen adjustment may

be disabled. When making an automatic

adjustment, be sure to either use the

Adjustment Pattern or try displaying an image

that makes the entire screen very bright.)

Adjusting the screen display

19

English

Manual screen adjustment

Adjustments can be made using On Screen Display

(OSD) Menu provided.

1. Display an image that makes the entire screen

very bright. If using Windows, you can open and

use the Adjustment Pattern on the accompanying

Utility Disk. (p. 18)

2. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK

127

PHASE 16

H

-

POS

200

V

-

POS 29

1024X768

V:75Hz H:60.0kHz

At this point relevant menu options can be

adjusted.

Each time the MENU button is pressed the next

menu is selected. (ADJUSTMENT → GAIN

CONTROL → WHITE BALANCE → MODE

SELECT → OSD Menu disappears)

Notes:

- The OSD Menu automatically disappears

approximately 30 seconds after the last

command.

- This explanation is based on using the

Adjustment Pattern (for Windows) to make

adjustments.

Adjusting the screen display

ADJUSTMENT Menu

ADJUSTMENT

MANUAL AUTO

CLOCK

127

PHASE 16

H

-

POS

200

V

-

POS 29

1024X768

V:75Hz H:60.0kHz

MANUAL:Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: SELECT button

- To go to the next menu: MENU button

CLOCK

The figure below demonstrates how to adjust so that

vertical flicker noise is not emitted. (

buttons)

PHASE

The figure below demonstrates how to adjust so that

horizontal flicker noise is not emitted. (

buttons)

Note:

- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS

(vertical positioning)

To center the screen image within the boundaries of

the screen, adjust the left-right (H-POS) values and

the up-down (V-POS) values. (

buttons)

Vertical flicker noise

Horizontal flicker noise

Screen frame

Adjustment

pattern

20

WHITE BALANCE Menu

WHITE

BALANCE

COOL

STD

WARM

USER

R

-

CONTRAST

G

-

CONTRAST

B

-

CONTRAST

1024X768

V:75Hz H:60.0kHz

Notes:

- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set

to [STD].

- Use the

buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and [B-

CONTRAST], in order to make fine adjustments.

- Use the SELECT button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- To go to the next menu: MENU button

COOL . . . Color tone bluer than standard

• . . . . . . Color tone slightly bluer than standard

STD . . . . . Color tone standard setting

• . . . . . . Color tone slightly redder than standard

WARM . . . Color tone redder than standard

USER

R-CONTRAST . . .

button for blue-green

button for red

G-CONTRAST . .

button for purple

button for green

B-CONTRAST . . .

button for yellow

button for blue

GAIN CONTROL Menu

GAIN

CONTROL

MANUAL AUTO

B L AC K

LEVEL

16

CONTRAST 80

1024X768

V:75Hz H:60.0kHz

MANUAL:Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted using the Auto Gain Control*

function.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: SELECT button

- To go to the next menu: MENU button

* Auto Gain Control function

- The Auto Gain Control adjusts contrast and black

level based on the brightest color of the image

displayed. If you are not using the Adjustment

Pattern it is necessary to have an area of 5 mm x

5 mm of white displayed, and if not adjustments

may not be possible. (In such case, [OUT OF

ADJUST] will appear and setting values remain

unchanged.)

- If the signal coming from the computer is

composite sync or sync on green, automatic

adjustment cannot be performed. Please perform

manual adjustment instead.

BLACK LEVEL

Total screen brightness can be adjusted while

watching the color pattern. (

buttons)

CONTRAST

While watching the color pattern, adjustments can be

made so that all graduations appear. (

buttons)

Adjusting the screen display

Color pattern

La pagina sta caricando ...

Sharp Computer Monitor LL-T15G1 Manuale utente

Questo manuale è adatto anche per

Sharp Computer Monitor LL-T15G1 Manuale utente

in altre lingue

Documenti correlati

Altri documenti