Sharp LL-T15G4 Manuale del proprietario

LCD Monitor

LCD Farbmonitor

Moniteur LCD

Monitor LCD

LL-T15G4

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D'EMPLOI

MANUALE D'USO

MANUAL DE FUNCIONAMIENTO

Untitled-38 2003/09/10, 15:391

Table of Contents/Inhaltsverzeichnis/Table des matières/Indice/Índice

Notice for Users in the USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Notice for Users in Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Notice for Users in the UK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Notice for Users in Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

TCO'99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Untitled-38 2003/09/10, 15:392

3

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in the USA

IMPORTANT:

To aid in reporting in case of loss or theft,

please record the monitor's model and serial

numbers in the space provided. The numbers

are located on the rear of the monitor.

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class

B computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T15G4-H/LL-T15G4-B

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Responsible Party: SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL: 1-800-BE-SHARP

* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.

Disposal of these materials may be regulated due to environmental considerations. For disposal or

recycling information, please contact your local authorities or the Electronics Industries

Alliance: www.eiae.org

Model No.:

Serial No.:

Untitled-41 2003/09/10, 15:413

4

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended

by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit

Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées

par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata

dalla direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ

73/23/ΕΟΚ, óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por

medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras

av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/

68/EEC.

CAUTION:

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION:

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT:

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER

HERAUSZIEHEN ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L'APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING:

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION:

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

PRECAUCION:

A FIN DE EVITAR DESCARGAS ELÉCTRICAS, DESCONECTE EL ENCHUFE DE LA RED ANTES DE

REALIZAR CUALQUIER OPERACIÓN DE SERVICIO.

ATTENZIONE:

PER EVITARE FOLGORAZIONI, SCOLLEGATE IL CAVO DI COLLEGAMENTO ALLA RETE IN

ALTERNATA PRIMA DI EFFETTUARE UN INTERVENTO DI SERVIZIO TECNICO.

ATTENZIONE:

PER UNO SCOLLEGAMENTO ELETTRICO COMPLETO, TIRATE FUORI LA SPINA PRINCIPALE.

Untitled-41 2003/09/10, 15:414

5

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows:

• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug

which is marked by the letter E or by the safety earth or coloured green or green-and-yellow.

• The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured black.

• The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured red.

Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified

electrician.

"WARNING: THIS APPARATUS MUST BE EARTHED."

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

Untitled-41 2003/09/10, 15:415

6

Congratulations!

You have just purchased a TCO'99 approved and

labelled product! Your choice has provided you with a

product developed for professional use. Your purchase

has also contributed to reducing the burden on the

environment and also to the further development of

environmentally adapted electronics products.

Why do we have environmentally labelled

computers?

In many countries, environmental labelling has become

an established method for encouraging the adaptation of

goods and services to the environment. The main

problem, as far as computers and other electronics

equipment are concerned, is that environmentally

harmful substances are used both in the products and

during their manufacture. Since it is not so far possible

to satisfactorily recycle the majority of electronics

equipment, most of these potentially damaging

substances sooner or later enter nature.

There are also other characteristics of a computer,

such as energy consumption levels, that are important

from the viewpoints of both the work (internal) and

natural (external) environments. Since all methods of

electricity generation have a negative effect on the

environment (e.g. acidic and climate-influencing

emissions, radioactive waste), it is vital to save energy.

Electronics equipment in offices is often left running

continuously and thereby consumes a lot of energy.

What does labelling involve?

This product meets the requirements for the TCO'99

scheme which provides for international and

environmental labelling of personal computers. The

labelling scheme was developed as a joint effort by the

TCO (The Swedish Confederation of Professional

Employees), Svenska Naturskyddsforeningen (The

Swedish Society for Nature Conservation) and Statens

Energimyndighet (The Swedish National Energy

Administration).

Approval requirements cover a wide range of issues:

environment, ergonomics, usability, emission of electric

and magnetic fields, energy consumption and electrical

and fire safety.

The environmental demands impose restrictions on the

presence and use of heavy metals, brominated and

chlorinated flame retardants, CFCs (freons) and

chlorinated solvents, among other things. The product

must be prepared for recycling and the manufacturer is

obliged to have an environmental policy which must be

adhered to in each country where the company

implements its operational policy.

The energy requirements include a demand that the

computer and/or display, after a certain period of

inactivity, shall reduce its power consumption to a lower

level in one or more stages. The length of time to

reactivate the computer shall be reasonable for the

user.

Labelled products must meet strict environmental

demands, for example, in respect of the reduction of

electric and magnetic fields, physical and visual

ergonomics and good usability.

Below you will find a brief summary of the environmental

requirements met by this product. The complete

environmental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): [email protected]

Current information regarding TCO'99 approved and

labelled products may also be obtained via the Internet,

using the address: http://www.tco-info.com/

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards,

cables, wires, casings and housings. Their purpose is to

prevent, or at least to delay the spread of fire. Up to

30% of the plastic in a computer casing can consist of

flame retardant substances. Most flame retardants

contain bromine or chloride, and those flame retardants

are chemically related to another group of environmental

toxins, PCBs. Both the flame retardants containing

bromine or chloride and the PCBs are suspected of

giving rise to severe health effects, including

reproductive damage in fish-eating birds and mammals,

due to the bio-accumulative* processes. Flame

retardants have been found in human blood and

researchers fear that disturbances in foetus

development may occur.

The relevant TCO'99 demand requires that plastic

components weighing more than 25 grams must not

contain flame retardants with organically bound bromine

or chlorine. Flame retardants are allowed in the printed

circuit boards since no substitutes are available.

Cadmium**

Cadmium is present in rechargeable batteries and in the

colour-generating layers of certain computer displays.

Cadmium damages the nervous system and is toxic in

high doses. The relevant TCO'99 requirement states

that batteries, the colour-generating layers of display

screens and the electrical or electronics components

must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and

switches. It damages the nervous system and is toxic in

high doses. The relevant TCO'99 requirement states

that batteries may not contain any mercury. It also

demands that mercury is not present in any of the

electrical or electronics components associated with the

labelled unit. There is however one exception. Mercury

is, for the time being, permitted in the back light system

of flat panel monitors as there today is no commercially

available alternative. TCO aims on removing this

exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO'99 requirement states that neither

CFCs nor HCFCs may be used during the manufacture

and assembly of the product. CFCs (freons) are

sometimes used for washing printed circuit boards.

CFCs break down ozone and thereby damage the

ozone layer in the stratosphere, causing increased

reception on earth of ultraviolet light with e.g. increased

risks of skin cancer (malignant melanoma) as a

consequence.

Lead**

Lead can be found in picture tubes, display screens,

solders and capacitors. Lead damages the nervous

system and in higher doses, causes lead poisoning. The

relevant TCO'99 requirement permits the inclusion of

lead since no replacement has yet been developed.

* Bio-accumulative is defined as substances which

accumulate within living organisms.

** Lead, Cadmium and Mercury are heavy metals which

are Bio-accumulative.

Untitled-41 2003/09/10, 15:416

7

EnglishDeutschFrançaisItalianoEspañolEnglish

Tips and safety precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting the monitor and turning the monitor on and off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting the monitor to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connection of headphones (commercially available) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting the monitor to a power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Changing between input terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Turning the power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjusting the screen display and speaker volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting the backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting the speaker volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Setting display mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the screen display (When using an analog signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Automatic screen adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Manual screen adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Adjusting the screen display (When using a digital signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Installing set-up information and the ICC profile (For Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Information about the ColorSync profile (For MacOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Instructions for attaching a VESA-compliant arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table of Contents

Untitled-40 2003/09/10, 15:417

8

Tips and safety precautions

- The TFT color LCD panel used in this monitor is

made with the application of high precision

technology. However, there may be minute

points on the screen where pixels never light or

are permanently lit. Also, if the screen is viewed

from an acute angle there may be uneven colors

or brightness. Please note that these are not

malfunctions but common phenomena of LCDs

and will not affect the performance of the

monitor.

- Do not display a still picture for a long time, as

this could cause an afterimage to remain.

- If the brightness is adjusted to the minimum

setting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using

a computer able to emit high quality video

signals.

- When the power is turned off or the monitor

switches to the power-saving mode, the image

might remain or an uneven image might stay on

the screen for a few seconds. Please note that

this is not a malfunction but is with LCD displays.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by

the customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be

upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is

high, or where the monitor may come into

contact with oil or steam, as this could lead to

fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric

shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the

monitor to come into contact with strong shocks

or vibrations. Causing the monitor to fall or

topple over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating

equipment or anywhere else where there is

likelihood of high temperature, as this may lead

to generation of excessive heat and outbreak of

fire.

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or over bend it. Also, do

not add extension cords. Damage to the cord

may result in fire or electric shock.

- Use only the power cord supplied with the

monitor.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating.

- Do not remove or insert the power plug with wet

hands. Doing so could result in electric shock.

Monitor and accessory checklist

- Please check that the following items are

included in the package.

- LCD monitor (1)

- Analog signal cable (1)

(model name: 0NIT15G4-0015 (LL-T15G4-H) /

0NIT15G4-0067 (LL-T15G4-B))

- Audio cable (1)

(model name: 0NIT17A3-U006 (LL-T15G4-H) /

0NIT17A3-U007 (LL-T15G4-B))

- CD-ROM: Utility Disk (For Windows/Macintosh) (1)

- Operation manual (1)

Notes:

- Use only the cables supplied with the monitor or

designated cables that are separately

purchased.

- The digital signal cable (DVI-D24 pin – DVI-D24

pin) is to be purchased separately.

(model name: NL-C04J)

- You are advised to retain the carton in case the

monitor needs to be transported.

- Sharp Corporation holds authorship rights to the

Utility Disk program. Do not reproduce it without

permission.

- The shape of the supplied accessories may not

be exactly same as shown in this manual.

Manual Scope

- In this manual, Microsoft Windows XP will be

referred to as "Windows XP", Microsoft Windows

Millennium as "Windows Me", Microsoft

Windows 2000 as "Windows 2000", Microsoft

Windows 98 as "Windows 98", Microsoft

Windows 95 as "Windows 95", and Microsoft

Windows Version 3.1 as "Windows 3.1". When

there is no need to distinguish between

programs, the term "Windows" will be used.

- Microsoft and Windows are registered

trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

- All other brand and product names are

trademarks or registered trademarks of their

respective holders.

02_LL-T15G4_gb.P65 10/20/2003, 3:28 PM8

9

EnglishDeutschFrançaisItalianoEspañolEnglish

Product description

65

42

1

10

98

14

3

7

12

11

13

1. INPUT button ...........................To switch between the signal's input terminals.

2. MENU button ........................... This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

3. / MODE button .....................When the OSD Menu is displayed:

This button is used to select menu options.

When the OSD Menu is not displayed:

This button is used to set DISPLAY MODE.

4. buttons .............................When the OSD Menu is displayed:

These buttons are used to select an option or adjust the value of the

selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness and speaker

volume.

5. Power LED...............................This LED is lit green when in use and orange when in power-saving

mode.

6. Power button............................Pressing this button turns the power on. (After turning the power on, it

may take a little time before an image appears on the screen.)

Press the button again to turn the power off.

7. Speakers..................................Audio entering via the external device connected to the monitor can

be heard.

8. Power terminal

9. DVI-D input terminal................ The computer's digital RGB output terminal can be connected here.

The separately-sold cable (NL-C04J) is necessary for connection.

(p.8)

It can be connected to a computer with a DVI-compatible output

terminal (DVI-D24 pin or DVI-I29 pin) and which has XGA output

ability. Depending on the computer to be connected, correct display

may or may not be possible.

10.Analog RGB input terminal .....The analog signal cable is connected here. The analog signal cable

included should be used.

11.Audio input terminal ................ A computer's audio output terminal can be connected here. The audio

cable included should be used.

12.Headphone terminal ............... Headphones (commercially available) can be connected here.

13.Security lock anchor................ By connecting a security lock (commercially available) to the security

lock anchor, the monitor is fixed so that it cannot be transported.

The security slot works in conjunction with Kensington Micro Saver

Security Systems.

14.Ventilation openings ...............Note: Never block the ventilation openings as this may lead to

overheating inside the monitor and result in malfunction.

Untitled-40 2003/09/10, 15:419

10

Product description

Standing up and adjusting the monitor

CAUTION!

- Be sure to hold both sides of the monitor when

adjusting the viewing angle. The LCD panel

used in this monitor is made of glass. Pressure

from hands on the LCD panel could cause

damage.

- Be careful not to allow your fingers to be

pinched.

- Not to fold up the monitor attaching the cable as

this could lead to a malfunction.

Standing up the monitor

1.Press down on the stand and lift up the top

section of the monitor.

- When raising the display section, movement

becomes harder in the middle of travel.

Continue raising by applying more force at that

point.

- Raise the display section until it stops.

(when tilted forward approx. 5º)

2.Adjust to an easy to view angle.

Angle adjustment

Press down on the stand and adjust it to a suitable

viewing angle.

- Do not use the monitor when tilted back beyond

approximately 25º. The monitor may fall over

leading to injury or malfunction.

Folding up the monitor

1.Remove the cables.

2.Press down on the stand and gently fold back

the monitor.

Prohibited range

approx. 25°

approx. 5°

approx. 25°

approx. 5°

Untitled-40 2003/09/10, 15:4110

11

EnglishDeutschFrançaisItalianoEspañolEnglish

CAUTION!

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to over bend the cable or add

extension cords as this could lead to a

malfunction.

Storing the cables

If necessary, cables can be stored inside of the

stand.

1.Remove the cover.

Pull the cover open while pushing the right and

left tabs of the cover.

2.Run cable along the back of the stand. Refit the

cover.

Be careful not to pinch the cable.

CAUTION!

- When adjusting the viewing angle, cables and

cords may be pulled. Therefore, ensure that the

cables and cords have sufficient slack.

cover

Analog signal cable

Connecting the monitor to a computer

Analog connection

- Use the accessory analog signal cable.

- Paying attention to connector direction, firmly

insert the signal cable vertically into the

connector, and then tighten the screws at both

sides.

If connecting to a D-sub15 pin 2 row Apple Power

Macintosh, attach a Macintosh conversion adapter

(commercially available) to the analog signal

cable.

Macintosh conversion adapter

Analog RGB terminal

(Mini D-Sub15 pin, 3 row)

Connecting the monitor and turning the monitor on and off

Untitled-40 2003/09/10, 15:4111

12

Headphone

terminal

Headphones

Digital connection

- Use the separately-sold digital signal cable.

(model name: NL-C04J)

- The monitor has an input for connecting to a

computer with a DVI-compatible output

connector (DVI-D24 pin or DVI-I29 pin) and XGA

output capability. (Depending on the type of

computer to be connected, the display may not

work correctly.)

- Paying attention to connector direction, firmly

insert the signal cable vertically into the

connector, and then tighten the screws at both

sides.

Connect the accessory audio cable

When the accessory audio cable is connected to

the audio output terminal of the computer, the

sound of the connected computer is output from

the monitor speakers. You can also use the

headphone jack of the display.

Connection of headphones

(commercially available)

Headphones (commercially available) can be

connected.

Note:

- When the headphones are connected, no sound

can be heard from the monitor speakers.

Connecting the monitor to a power

source

Audio cable

Digital signal cable

Digital RGB output

terminal

DVI-D input terminal

Power terminal

AC outlet

Power cord

Audio input terminal

Audio output terminal

Connecting the monitor and turning the monitor on and off

Untitled-40 2003/09/10, 15:4112

13

EnglishDeutschFrançaisItalianoEspañolEnglish

Turning the power on

1.Press the monitor's power button.

2.Turn on the computer.

The power LED will be lit green, and the screen

will display an image.

- If the input terminal to which the computer is

connected has not been selected, the screen

will not be displayed. If necessary, perform input

terminal switching.

Notes:

- When using an analog signal, perform an

automatic screen adjustment under the following

conditions (p.16):

- Using the monitor for the first time.

- After having changed the system settings

during use.

- Depending on the type of computer or OS, you

may need to install the monitor set-up

information on your system. (p.26)

- When connecting to a notebook, if the notebook

computer's screen is set to display at the same

time, the MS-DOS screen may not display

properly. In this case, change the setting to

display only the LCD monitor.

Changing between input terminals

Use the INPUT button to switch between signal

input terminals.

Analog RGB input DVI-D input

terminal terminal

INPUT

INPUT

INPUT

Note:

- When there is no input signal, [NO SIGNAL] is

displayed.

Turning the power off

1.Turn the computer off.

2.Press the monitor's power button.

The power LED will disappear.

If the monitor is not going to be used for a long

period of time, be sure to unplug it from the AC

outlet.

Power LED

Power button

Power LED Power button

Connecting the monitor and turning the monitor on and off

Untitled-40 2003/09/10, 15:4113

14

Adjusting the screen display and speaker volume

For analog signal

1.First perform an automatic adjustment. (p.16)

2.Perform manual adjustment where necessary.

(p.17)

For digital signal

The monitor can generally be used without

adjustment. If necessary perform manual

adjustment. (p.20)

Note:

- All adjustments will be saved even after turning

the power off.

Resetting all adjustment values

All adjustment values can be returned to their

original ex-factory values in one command.

1.Turn off the monitor power.

2.Press the MENU button and the / MODE

button simultaneously, and while doing this

press the power button (i.e. turn the power on).

Continue to press the buttons until [ALL RESET]

appears on the screen. Reset is complete when

the displayed message disappears.

Notes:

- While [ALL RESET] is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

ADJUSTMENT Menu reset (for analog signal)

Settings of items in the ADJUSTMENT Menu

(CLOCK, PHASE, H-POS, V-POS) can be returned

to their original ex-factory values.

1.Turn on the monitor power.

2.Press the MENU button and the button

simultaneously. When [RESET] appears on the

screen, the reset is complete.

Notes:

- While [RESET] is displayed, the control buttons

are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

Adjustment lock function

By disabling the control buttons (i.e. setting the

lock) any attempted changes to adjusted values

will be voided.

1.Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

[ADJUSTMENT LOCKED] will appear on the

screen, and the lock will be set.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Adjustment lock release

1.Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

[ADJUSTMENT UNLOCKED] will appear on the

screen, and the lock will be removed.

Adjusting the backlight

1.Without the OSD Menu being displayed, press

the or the button.

2.Check that [BRIGHT] is selected.

If it is not selected, press the / MODE button

and select [BRIGHT].

BRIGHT

VOLUME

SELECT

3.Adjust by pressing the button (darker) or

button (lighter).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

Untitled-40 2003/09/10, 15:4114

15

EnglishDeutschFrançaisItalianoEspañolEnglish

Adjusting the speaker volume

1.Without the OSD Menu being displayed, press

the or the button.

2.Check that [VOLUME] is selected.

If it is not selected, press the / MODE button

and select [VOLUME].

BRIGHT

VOLUME

SELECT

3.Adjust by pressing the button (decrease) or

button (increase).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

Adjusting the screen display and speaker volume

Setting display mode

Color tone or brightness can be changed with one

command.

STD

Displays image with the color tone results from

original scheme of liquid crystal panel.

OFFICE

Display brightness is lowered. (This mode saves

power.)

sRGB

sRGB is international standard of color

representation specified by IEC (International

Electrotechnical Commission).

Color conversion is made in taking account of

liquid crystal's characteristics and represents

color tone close to its original image.

VIVID

Displays an image with dynamic and vivid

primary colors.

- If [DISPLAY MODE] is set to [sRGB] or [VIVID],

[WHITE BALANCE] is set to [STD].

How to set

Press the / MODE button when the OSD Menu is

not displayed.

Each time the button is pressed the next menu

item appears. (STD → OFFICE →sRGB → VIVID

→ STD)

On Screen display for adjustment disappears

several seconds after the last operation.

Untitled-40 2003/09/10, 15:4115

16

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be

adjusted automatically (CLOCK, PHASE, H-POS,

V-POS).

Note:

- When setting up this monitor for the first time or

after having changed an aspect of the current

system, perform an automatic screen adjustment

before use.

Automatic adjustment screen display

To perform an automatic adjustment, first display

an image that makes the entire screen very bright.

If you are using Windows, you can use the

Adjustment Pattern on the accompanying Utility

Disk.

Opening the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000/Me/

XP, and assumes that the CD-ROM drive is "D"

drive.

1.Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2.Open [My Computer] and select CD-ROM. If

using Windows 3.1, open [File Manager] and

choose "D" drive.

3.Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern

will appear.

Adjustment Pattern

After completing the adjustment, press the

computer's [Esc] key to exit the Adjustment

Program.

Note:

- If your computer's display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the input signal

specification and is not a malfunction.)

Adjusting the screen display (When using an analog signal)

Adjusting the screen automatically

1.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 30

H-POS 200

V-POS 29

1024x768 ANALOG

V:60Hz H:48.4kHz

2.Press the button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3.Press the MENU button 4 times to make the OSD

(On Screen Display) Menu disappear.

Notes:

- In most cases automatic adjustment is sufficient.

- It may not be possible to achieve correct

adjustment with the first automatic adjustment. In

such a case, try repeating the automatic

adjustment 2 or 3 times.

- If necessary due to any of the following, manual

adjustments (p.17) can be performed after the

automatic adjustment.

- When further fine adjustment is needed.

- When [OUT OF ADJUST] is displayed. (When

the screen displays an entirely dark image, the

automatic screen adjustment may be disabled.

When making an automatic adjustment, be

sure to either use the Adjustment Pattern or try

displaying an image that makes the entire

screen very bright.)

- When the computer

's video input signals are

Composite Sync or Sync on Green. (Automatic

adjustments may not be possible.)

- Automatic adjustment may not be achieved

correctly depending on what is displayed on the

screen - moving pictures or the MS-DOS prompt

etc.

Untitled-40 2003/09/10, 15:4116

17

EnglishDeutschFrançaisItalianoEspañolEnglish

Adjusting the screen display (When using an analog signal)

Manual screen adjustment

Adjustments can be made using OSD (On Screen

Display) Menu provided.

1.Display an image that makes the entire screen

very bright. If using Windows, you can open and

use the Adjustment Pattern on the

accompanying Utility Disk. (p.16)

2.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 30

H-POS 200

V-POS 29

1024x768 ANALOG

V:60Hz H:48.4kHz

At this point relevant menu options can be

adjusted.

Each time the MENU button is pressed the next

menu is selected. (ADJUSTMENT → GAIN

CONTROL → WHITE BALANCE → MODE

SELECT → OSD Menu disappears)

Notes:

- The OSD Menu automatically disappears

approximately 30 seconds after the last

command.

- This explanation is based on using the

Adjustment Pattern (for Windows) to make

adjustments.

ADJUSTMENT Menu

ADJUSTMENT

MANUAL AUTO

CLOCK 127

PHASE 30

H-POS 200

V-POS 29

1024x768 ANALOG

V:60Hz H:48.4kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: / MODE button

- To go to the next menu: MENU button

CLOCK

The figure below demonstrates how to adjust so that

vertical flicker noise is not emitted. ( buttons)

PHASE

The figure below demonstrates how to adjust so

that horizontal flicker noise is not emitted.

( buttons)

Note:

- Adjustments to [PHASE] should be made only

after [CLOCK] has been correctly set.

H-POS (horizontal positioning) and V-POS

(vertical positioning)

To center the Adjustment Pattern within the

boundaries of the screen, adjust the left-right (H-

POS) values and the up-down (V-POS) values.

( buttons)

Vertical flicker noise

Horizontal flicker noise

Adjustment

Pattern

Screen frame

Untitled-40 2003/09/10, 15:4117

18

GAIN CONTROL Menu

GAIN CONTROL

MANUAL AUTO

BLACK LEVEL 32

CONTRAST 50

1024x768 ANALOG

V:60Hz H:48.4kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted using the Auto Gain Control*

function.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: / MODE button

- To go to the next menu: MENU button

* Auto Gain Control function

- The Auto Gain Control adjusts contrast and

black level based on the brightest and darkest

colors of the image displayed. If you are not

using the Adjustment Pattern it is necessary to

have black area and white area of at least 5 mm

x 5 mm on the screen. Adjustment may not be

possible without those areas.

- If the signal coming from the computer is

Composite Sync or Sync on Green, automatic

adjustment cannot be performed. Please

perform manual adjustment instead.

- If [OUT OF ADJUST] is displayed, perform

manual adjustment.

- When using the Auto Gain Control function, set

[WHITE BALANCE] to other than [USER]. If

[USER] is set, the Auto Gain Control function

cannot be used.

BLACK LEVEL

Total screen brightness can be adjusted while

watching the color pattern. ( buttons)

CONTRAST

While watching the color pattern, adjustments can

be made so that all gradations appear.

( buttons)

Color pattern

Adjusting the screen display (When using an analog signal)

WHITE BALANCE Menu

WHITE BALANCE

COOL STD WARM USER

R-CONTRAST

G-CONTRAST

B-CONTRAST

1024x768 ANALOG

V:60Hz H:48.4kHz

Notes:

- On settings other than [STD] not all gradations

can be displayed. To display all gradations, set

to [STD].

- If [DISPLAY MODE] is set to [sRGB] or [VIVID],

no other setting than [STD] can be selected.

- Use the buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting [USER] will display the setting values for

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST], in order to make fine adjustments.

- Use the / MODE button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- To go to the next menu: MENU button

COOL ....... Color tone bluer than standard

• ............. Color tone slightly bluer than standard

STD .......... Color tone standard setting

• ............. Color tone slightly redder than standard

WARM ..... Color tone redder than standard

USER

R-CONTRAST.....

button for blue-green

button for red

G-CONTRAST..... button for purple

button for green

B-CONTRAST ..... button for yellow

button for blue

Untitled-40 2003/09/10, 15:4118

19

EnglishDeutschFrançaisItalianoEspañolEnglish

MODE SELECT Menu

MODE SELECT

OSD H-POSITION

OSD V-POSITION

SCALING 3

COLORS 260K 16M

LANGUAGE

1024x768 ANALOG

V:60Hz H:48.4kHz

Notes:

- Depending on the resolution of the input signal,

even if menu options can be selected, the

display may not change.

- To choose a menu option: / MODE button

- To complete adjustment: MENU button

OSD H-POSITION (OSD horizontal position)

The position of the OSD Menu can be moved to

the left and right. ( buttons)

OSD V-POSITION (OSD vertical position)

The position of the OSD Menu can be moved up

and down. ( buttons)

SCALING (Level of scaling)

When the display is enlarged, the sharpness of the

image can be set. ( buttons)

Note:

- When the display mode is set to less than

1024 x 768 pixels, the display is enlarged to

cover the whole screen (i.e. the side ratio of the

display may change).

COLORS

Maximum display colors can be set. (

buttons)

260K (approx. 260,000)

16M (approx. 16.19 million)

LANGUAGE

You can choose the language used in OSD Menu.

1.Press the button.

The Language Selection Menu will be displayed

on the screen.

2.Use the / MODE button to choose a language.

3.Press the MENU button.

Language Selection Menu will disappear.

Adjusting the screen display (When using an analog signal)

Untitled-40 2003/09/10, 15:4119

20

Adjusting the screen display (When using a digital signal)

Adjustments can be made using OSD (On Screen

Display) Menu provided.

1.Display an image that makes the entire screen

very bright. If using Windows, you can open and

use the Adjustment Pattern on the accompanying

Utility Disk. (p.16)

2.Press the MENU button 3 times.

The WHITE BALANCE Menu will be displayed.

WHITE BALANCE

COOL STD WARM USER

R-CONTRAST

G-CONTRAST

B-CONTRAST

1024x768 DIGITAL

V:60Hz H:48.4kHz

At this point relevant menu options can be

adjusted.

Each time the MENU button is pressed the next

menu is selected. (WHITE BALANCE → MODE

SELECT → OSD Menu disappears)

Notes:

- Like when making an analog connection, the

ADJUSTMENT Menu and the GAIN CONTROL

Menu are displayed. However, you don't need to

adjust these items.

- The OSD Menu automatically disappears

approximately 30 seconds after the last

command.

WHITE BALANCE Menu

WHITE BALANCE

COOL STD WARM USER

R-CONTRAST

G-CONTRAST

B-CONTRAST

1024x768 DIGITAL

V:60Hz H:48.4kHz

Notes:

- On settings other than [STD] not all gradations

can be displayed. To display all gradations, set

to [STD].

- If [DISPLAY MODE] is set to [sRGB] or [VIVID],

no other setting than [STD] can be selected.

- Use the buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting [USER] will display the setting values

for [R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST], in order to make fine

adjustments.

- Use the / MODE button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- To go to the next menu: MENU button

COOL ....... Color tone bluer than standard

• ............. Color tone slightly bluer than standard

STD .......... Color tone standard setting

• ............. Color tone slightly redder than standard

WARM ..... Color tone redder than standard

USER

R-CONTRAST.....

button for blue-green

button for red

G-CONTRAST..... button for purple

button for green

B-CONTRAST ..... button for yellow

button for blue

Untitled-40 2003/09/10, 15:4120

La pagina sta caricando ...

Sharp LL-T15G4 Manuale del proprietario

Sharp LL-T15G4 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti