Woods PRD8400E Manuale utente

OPERATOR'S MANUAL

PREMIER

REAR DISCHARGE

MOWERS

MAN1260

(4/09/2018)

PRD6000E

PRD7200E

PRD8400E

Gen’l CE Euro (Rev. 3/27/2017)

2 Introduction

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods

®

dealer. Read manual instructions

and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual

are completed before releasing equipment to the owner.

PRODUCT REGISTRATION:

The end user must complete the online Product Registration form at the Woods Website. End users can register all

Woods product at WoodsEquipment.eu under Warranty

.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and

safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become

acquainted with all the adjustment and operating procedures before attempting to operate. Replacement manuals can be

obtained from your dealer. To locate your nearest dealer, check the Dealer Locater at www.WoodsEquipment.eu, or call

+32 10 301111 in Belgium.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and

satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.

Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary

tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for

safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces

provided:

Model: _______________________________ Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment.

The terms CAUTION, WARNING and DANGER are used in conjunction with the Safety-Alert Symbol, (a triangle with

an exclamation mark), to indicate the degree of hazard for items of personal safety.

Introduction 3

MAN1260 (4/09/2018)

TABLE OF CONTENTS

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY DECALS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

DEALER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

DEALER CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

PRODUCT WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

REPLACEMENT PARTS WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

SPECIFICATIONS

GENERAL INFORMATION

 Some illustrations in this manual show the equipment with safety

shields removed to provide a better view. This equipment should never

be operated with any necessary safety shielding removed.

The purpose of this manual is to assist you in operating and maintaining your

mower. Read it carefully. It furnishes information and instructions that will help

you achieve years of dependable performance. These instructions have been

compiled from extensive field experience and engineering data. Some informa-

tion may be general in nature, due to unknown and varying operating condi-

tions. However, through experience and these instructions, you should be able

to develop procedures suitable to your particular situation.

The illustrations and data used in this manual were current at the time of print-

ing. However, due to possible inline production changes, your machine may

vary slightly in detail. We reserve the right to redesign and change the

machines as may be necessary without notification.

Throughout this manual, references are made to right and left directions. These

are determined by standing behind the tractor facing the direction of forward

travel.

PRD6000E

PRD7200E PRD8400E

3-Point Hitch Category 1 Category 1 Category 1

Cutting Width 1524 mm (1.5 m) (60") 1829 mm (1.8 m) (72") 2134 mm (2.1 m) (84")

Cutting Height Range 25.4 - 139.7 mm

(1" - 5-1/2")

25.4 - 139.7 mm

(1" - 5-1/2")

25.4 - 108.0 mm

(1" - 4-1/4")

Operating Weight with

Chain Shielding

296 kg (653 lbs) 326 kg (719 lbs) 376 kg (830 lbs)

Blade Speed (feet per minute) 5517 m/min (18,100) 5486 m/min (18,000) 5456 m/min (17,900)

Blade Speed (RPM) 3,295 2,748 2,329

Blade Spindles 3 3 3

Number of Blades 3 3 3

Universal Drive Series ASAE Cat. 3 ASAE Cat. 3 ASAE Cat. 3

Caster Wheels 101.6 x 254 mm

(4.00 x 10")

101.6 x 254 mm

(4.00 x 10")

101.6 x 254 mm

(4.00 x 10")

Tractor PTO Speed RPM 540 540 540

Recommended Maximum

Tractor Horsepower

60 60 60

Mower Frame Thickness 4.2 mm (8 ga) 4.2 mm (8 ga) 4.2 mm (8 ga)

4 Safety

RD 54/60/72E UK SR (1/15/2008)

TRAINING

 Safety instructions are important! Read all attachment and power unit

manuals; follow all safety rules and safety decal information. (Replacement

manuals and safety decals are available from your dealer. To locate your near-

est dealer, check the Dealer Locator at www.WoodsEquipment.eu, or call +32

10 301111 in Belgium.) Failure to follow instructions or safety rules can result in

serious injury or death.

 Know your controls and how to stop engine and attachment quickly in an

emergency.

 If you do not understand any part of this manual and need assistance, see

your dealer.

 Operators must be instructed in and be capable of the safe operation of

the equipment, its attachments, and all controls. Do not allow anyone to oper-

ate this equipment without proper instructions.

 Never allow children or untrained persons to operate equipment.

PREPARATION

 Check that all hardware is properly installed. Always tighten to torque chart

specifications unless instructed otherwise in this manual.

 Always wear relatively tight and belted clothing to avoid entanglement in

moving parts. Wear sturdy, rough-soled work shoes and protective equipment

for eyes, hair, hands, hearing, and head; and respirator or filter mask where

appropriate.

 Make sure attachment is properly secured, adjusted, and in good operat-

ing condition.

 Make sure spring-activated locking pin or collar slides freely and is seated

firmly in tractor PTO spline groove.

 Make sure driveline shield tether chains are attached to the tractor and

equipment as shown in this manual. Replace if damaged or broken. Check that

driveline guards rotate freely on driveline before putting equipment into service.

 Before starting power unit, check all equipment driveline guards for dam-

age. Replace any damaged guards. Make sure all guards rotate freely on all

drivelines. If guards do not rotate freely on drivelines, repair and replace bear-

ings before putting equipment into service.

 Power unit must be equipped with ROPS or ROPS cab and seat belt.

Keep seat belt securely fastened. Falling off power unit can result in death from

being run over or crushed. Keep foldable ROPS systems in “locked up” position

at all times.

 Remove accumulated debris from this equipment, power unit, and engine

to avoid fire hazard.

 Make sure all safety decals are installed. Replace if damaged. (See Safety

Decals section for location.)

 Make sure shields and guards are properly installed and in good condition.

Replace if damaged.

 A minimum 20% of tractor and equipment weight must be on the tractor

front wheels when attachments are in transport position. Without this weight,

tractor could tip over, causing personal injury or death. The weight may be

attained with front wheel weights, ballast in tires or front tractor weights. Weigh

the tractor and equipment. Do not estimate.

OPERATION



Inspect and clear area of stones, branches, or other hard objects that

might be thrown, causing injury or damage.

 Never direct discharge toward people, animals, or property.

 Keep bystanders away from equipment.

 Do not operate or transport equipment while under the influence of alcohol

or drugs.

 Operate only in daylight or good artificial light.

 Full chain shielding must be installed when operating in populated areas or

other areas where thrown objects could injure people or damage property.

• If this machine is not equipped with full chain shielding, operation must

be stopped when anyone comes within 300 feet (92 m).

• This shielding is designed to reduce the risk of thrown objects. The

mower deck and protective devices cannot prevent all objects from escap-

ing the blade enclosure in every mowing condition.

It is possible for objects

to ricochet and escape, traveling as much as 300 feet (92 m).

 Keep hands, feet, hair, and clothing away from equipment while engine is

running. Stay clear of all moving parts.

 Always comply with all state and local lighting and marking requirements.

 Never allow riders on power unit or attachment.

 Always sit in power unit seat when operating controls or starting engine.

Securely fasten seat belt, place transmission in neutral, engage brake, and

ensure all other controls are disengaged before starting power unit engine.

 Operate tractor PTO at 540 RPM. Do not exceed.

 Connect PTO driveline directly to power unit PTO shaft. Never use adapter

sleeves or adapter shafts. Adapters can cause driveline failures due to incor-

rect spline or incorrect operating length and can result in personal injury or

death.

 Look down and to the rear and make sure area is clear before operating in

reverse.

 Do not operate or transport on steep slopes.

 Do not stop, start, or change directions suddenly on slopes.

 Use extreme care and reduce ground speed on slopes and rough terrain.

 Watch for hidden hazards on the terrain during operation.

 Stop power unit and implement immediately upon striking an obstruction.

Dismount power unit, using proper procedure. Inspect and repair any damage

before resuming operation.

TRANSPORTATION

 Use additional caution and reduce speed when under adverse surface

conditions, turning, or on inclines.

 Do not operate PTO during transport.

 A minimum 20% of tractor and equipment weight must be on the tractor

front wheels when attachments are in transport position. Without this weight,

tractor could tip over, causing personal injury or death. The weight may be

attained with front wheel weights, ballast in tires or front tractor weights. Weigh

the tractor and equipment. Do not estimate.

 Do not operate or transport on steep slopes.

 Do not operate or transport equipment while under the influence of alcohol

or drugs.

 Always comply with all state and local lighting and marking requirements.

 Never allow riders on power unit or attachment.

MAINTENANCE

 Before working underneath, carefully read Operator’s Manual instructions,

disconnect driveline, raise mower, securely block up all corners with jack-

stands, and check stability. Secure blocking prevents equipment from dropping

due to hydraulic leak down, hydraulic system failures, or mechanical compo-

nent failures.

 Do not modify or alter or permit anyone else to modify or alter the equip-

ment or any of its components in any way.

 Always wear relatively tight and belted clothing to avoid entanglement in

moving parts. Wear sturdy, rough-soled work shoes and protective equipment

for eyes, hair, hands, hearing, and head; and respirator or filter mask where

appropriate.

 Never go underneath equipment (lowered to the ground or raised) unless

it is properly blocked and secured. Never place any part of the body under-

neath equipment or between moveable parts even when the engine has been

turned off. Hydraulic system leak down, hydraulic system failures, mechanical

failures, or movement of control levers can cause equipment to drop or rotate

unexpectedly and cause severe injury or death. Follow Operator's Manual

instructions for working underneath and blocking requirements or have work

done by a qualified dealer.

 Make sure attachment is properly secured, adjusted, and in good operat-

ing condition.

 Keep all persons away from operator control area while performing adjust-

ments, service, or maintenance.

 Make certain all movement of equipment components has stopped before

approaching for service.

 Frequently check blades. They should be sharp, free of nicks and cracks,

and securely fastened.

 Do not handle blades with bare hands. Careless or improper handling may

result in serious injury.

 Your dealer can supply genuine replacement blades. Substitute blades

may not meet original equipment specifications and may be dangerous.

 Tighten all bolts, nuts, and screws to torque chart specifications. Check

that all cotter pins are installed securely to ensure equipment is in a safe condi-

tion before putting unit into service.

 Make sure all safety decals are installed. Replace if damaged. (See Safety

Decals section for location.)

 Make sure shields and guards are properly installed and in good condition.

Replace if damaged.

 Wear gloves when installing belt. Be careful to prevent fingers from being

caught between belt and pulley.

 Use care when installing or removing belt from spring-loaded idler. Springs

store energy when extended and, if released suddenly, can cause personal

injury.

STORAGE

 Follow manual instructions for storage.

 Keep children and bystanders away from storage area.

Safety is a primary concern in the design and manufacture of our products.

Unfortunately, our efforts to provide safe equipment can be wiped out by

an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control

and accident prevention are dependent upon the awareness, concern,

judgement, and proper training of personnel involved in the operation,

transport, maintenance, and storage of equipment.

It has been said, “The best safety device is an informed, careful operator.”

We ask you to be that kind of operator.

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Safety 5

MAN1260 (4/09/2018)

1 - 15503 2 - 18867

3 - Serial Number Plate

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter

through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest

dealer, check the Dealer Locator at www. WoodsEquipment.eu, or call +32 10 301111 in Belgium.

11 - 57123 - 9" Red Rear Reflector

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

6 Safety

MAN1260 (4/09/2018)

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

7 - 18865

8 - 1004114

9 - 33347

5 - 18864

6 - 18877 10 - 1003751

4 - 18866

Declaration of Conformity 7

MAN1260 (4/09/2018)

Declaration of Conformity

8 Operation

MAN1260 (4/09/2018)

OPERATION

The operator is responsible for the safe operation of the mower. The operator

must be properly trained. Operators should be familiar with the mower, the trac-

tor, and all safety practices before starting operation. Read the safety rules and

safety decals on pages 4 to 6.

This mower is designed for lawn and grass mowing. It is not designed for rough

conditions or heavy weed mowing. It is equipped with suction type blades for

best results in lawn mowing.

Recommended mowing speed for most conditions is from 3.2 to 8.0 km/h (2 to

5 mph).

 Full chain or rubber shielding must be installed when operating in

populated areas or other areas where thrown objects could injure people

or damage property.

• If this machine is not equipped with full chain or rubber shielding,

operation must be stopped when anyone comes within 300 feet (92

m).

• This shielding is designed to reduce the risk of thrown objects.

The mower deck and protective devices cannot prevent all objects

from escaping the blade enclosure in every mowing condition.

It is

possible for objects to ricochet and escape, traveling as much as 300

feet (92 m).

 Never allow children or untrained persons to operate equipment.

 Keep bystanders away from equipment.

 Make sure spring-activated locking pin or collar slides freely and is

seated firmly in tractor PTO spline groove.

 Before working underneath, carefully read Operator’s Manual

instructions, disconnect driveline, raise mower, securely block up all cor-

ners with jackstands, and check stability. Secure blocking prevents

equipment from dropping due to hydraulic leak down, hydraulic system

failures, or mechanical component failures.

 Keep all persons away from operator control area while performing

adjustments, service, or maintenance.

 Stop power unit and implement immediately upon striking an

obstruction. Dismount power unit, using proper procedure. Inspect and

repair any damage before resuming operation.

 Always wear relatively tight and belted clothing to avoid getting

caught in moving parts. Wear sturdy, rough-soled work shoes and protec-

tive equipment for eyes, hair, hands, hearing, and head; and respirator or

filter mask where appropriate.

TRACTOR STABILITY

 A minimum 20% of tractor and equipment weight must be on the

tractor front wheels when attachments are in transport position. Without

this weight, tractor could tip over, causing personal injury or death. The

weight may be attained with front wheel weights, ballast in tires or front

tractor weights. Weigh the tractor and equipment. Do not estimate.

Figure 1.

Tractor Stability

ATTACHING MOWER TO TRACTOR

 Make sure spring-activated locking pin or collar slides freely and is

seated firmly in tractor PTO spline groove.

The standard 1-3/8" 6B-spline driveline with a QD yoke is used to connect the

mower to the tractor.

1.

Attach the mower hitch pins to the lower tractor lift arms and secure.

2.

Attach tractor top link (1), Figure 2, to mower top link bracket attachment

point A. Connect the driveline to the tractor PTO shaft.

Figure 2

. Attachment Points

1. Tractor top link

A. Mower top link attach-

ment point

Operation 9

MAN1260 (4/09/2018)

Figure 3

. Attaching Mower to Tractor

3.

Attach tether chain to tractor drawbar (Figure 3).

4.

Adjust the tractor lower 3-point arm anti-sway devices to prevent mower

from swinging side to side during transport.

CUTTING HEIGHT ADJUSTMENT

 Keep all persons away from operator control area while performing

adjustments, service, or maintenance.

NOTICE

■

Avoid low cutting heights. Striking the ground with blades pro-

duces one of the most damaging shock loads a mower can encounter.

Allowing blades to contact ground repeatedly will cause damage to

mower and drive.

1.

Level mower from side to side. Check by measuring from mower frame to

the ground at each deck rail.

2.

Verify that the same amount of spacers are under all caster arms.

3.

Loosen cap screws that attach caster arm assembly to deck.

4.

Set mower on the ground.

5.

Retighten cap screws. This equalizes the clearance in the bolt holes.

6.

Adjust front of mower level with or slightly lower than the rear to obtain

best mowing results.

7.

Control cutting height by adjusting front and rear caster wheels.

8.

To raise rear of mower, move caster adjustment spacers under rear

caster arms, .

9.

To raise front of mower, move spacers under front caster wheel arms.

Figure 4

. Cutting Height Adjustment

Remember, measurement at location A (Figure 4) should not be less than loca-

tion B and should not be over 12.7 mm (1/2") greater than location B.

Figure 5.

Height Adjustment with Caster Arm Spacers

TRACTOR TOP LINK ADJUSTMENT

When the cutting height is set, adjust tractor top link until mower top link attach-

ment point (A) is aligned vertically with mower hitch pin (B), Figure 6.

Adjust tractor top link so mower is level between caster wheel and ground

(dimension C), Figure 7. This will allow the mower to follow ground contour.

The mower has three lower hitch plate attachment points (D), Figure 6. It may

be necessary to change the mower hitch plate attachment point to obtain

proper tire clearance and/or lift height.

CM906

Tether Chain

Table 1: Cutting Height Chart

Spacers Required Under

Caster Arm Pivot Tube

Spacers

Cutting Height 12.7

mm

(1/2")

19.1

mm

(3/4")

25.4

mm

(1")

*31.8 mm (1-

1/4")

Spring

25.4 mm

(1")

38.1 mm

(1-1/2")

1-1/2”

1

50.8 mm

(2")

1

63.5 mm

(2-1/2")

11

76.5 mm

(3")

2

88.9 mm

(3-1/2")

12

101.6 mm

(4")

*111

108.0 mm

(4-1/4")

112 1

114.3 mm

(4-1/2")

*111 1

127 mm

(5")

*121

139.7 mm

(5-1/2")

*112 1

* PRD6000E and PRD7200E Only

10 Operation

MAN1260 (4/09/2018)

Figure 6.

Top Link Adjustment

Figure 7.

Caster Wheel Distance

FRONT CASTER ARM CONFIGURATION

For PRD6000E & PRD7200E only

The front casters can be set in two positions. Figure 8 shows the two possible

configurations for the PRD6000E and PRD7200E front caster arms.

●

The inner position allows the outside edge of the mower to be used for

trimming under shrubs or fences.

●

The outer position provides the most clearance for rear tractor tire inter-

ference.

To change configurations, remove the cap screws and nuts and move the arms

from one side of the wheel rail to the other. Secure with same hardware.

The rear caster arms should be mounted as shown.

NOTE: The PRD8400E front caster arms are fixed and cannot be changed.

Figure 8.

Front Caster Arm Configuration for PRD6000E & PRD7200E Only

FRONT CASTER WHEEL INTERFERENCE CHECK

NOTICE

■

Do not operate tractor and mower until this interference check

has been performed. If you change tractors, you must perform the check

for that mounting.

Figure 9

. Front Caster Wheel Interference Check

1. Tractor top link

A. Mower top link

attachment

point

B. Mower hitch pin

D. Lower hitch

plate attach-

ment point

E. Mower hitch

plate

Operation 11

MAN1260 (4/09/2018)

Perform this check with all of the spacers and springs above the caster wheel

arm. This will place the caster wheels in their highest position and provide the

lowest cutting height for the mower.

1.

Raise mower with tractor hydraulics to 406.4 mm (16") at dimension C or

maximum height of tractor lift, whichever is less.

2.

Pivot both front caster wheels forward and check that there is clearance

between caster wheels and tractor tires.

3.

If there is interference on models PRD6000E and PRD7200E, mount

front casters in the outer position. If interference continues, adjust mower

hitch plate (E) as shown in Figure 8.

NOTE: On model PRD8400E, caster wheel width is not adjustable; see tractor

operator's manual and adjust tractor wheels to narrower spacing.

FRONT ROLLER (OPTIONAL)

The caster wheels and side skids effectively reduce scalping in most cases.

However, you may encounter areas where the caster wheels and/or side skids

drop into depressions and allow center of the mower to contact ground and

scalp. An optional front roller may be installed to minimize scalping. See page

23.

OPERATING TECHNIQUE

 Stop power unit and implement immediately upon striking an

obstruction. Dismount power unit, using proper procedure. Inspect and

repair any damage before resuming operation.

Power for operating mower is supplied by tractor PTO. Operate PTO at 540

rpm. Know how to stop tractor and mower quickly in an emergency.

If mower becomes plugged causing belt to slip for over two seconds follow

these steps:

1.

Maneuver equipment into a previously cut area and allow mower to clear

accumulated material.

2.

Continue running at least two minutes, allowing pulleys to cool. Stopping

the mower in contact with a very hot pulley will bake and ruin belt.

Proper ground speed will depend upon the terrain, the height, and type and

density of material to be cut.

Normally, ground speed will range from 3.2 to 8 Km/h (2 to 5 mph). Tall dense

material should be cut at a low speed; thin medium-height material can be cut

at a faster ground speed.

Always operate tractor PTO at 540 rpm to maintain proper blade speed and

produce a clean cut.

Under certain conditions, tractor tires may roll some grass down and prevent it

from being cut at the same height as the surrounding area. When this occurs,

reduce your ground speed, but maintain PTO at 540 rpm. The lower ground

speed will permit grass to partially rebound.

In general, lower cutting heights give a more even cut and leave less tire

tracks. However, it is better to cut grass frequently rather than too short. Short

grass deteriorates rapidly in hot weather and invites weed growth during grow-

ing seasons. Follow local recommendations for the suitable cutting height in

your area.

Operating Tips

 Inspect and clear area of stones, branches, or other hard objects that

might be thrown, causing injury or damage.

Extremely tall material should be cut twice. Set mower at a higher cutting

height for the first pass. Then cut at desired height, 90 degrees to the first pass.

Remember, sharp blades produce cleaner cuts and require less power.

Analyze area to be cut to determine the best procedure. Consider height and

type of grass and terrain type: hilly, level, or rough.

Plan your mowing pattern to travel straight forward whenever possible. Mow

with uncut grass to the right. This will distribute the clippings over the cut area.

Operating on Uneven Terrain

 Do not operate or transport on steep slopes.

 Do not stop, start, or change directions suddenly on slopes.

 Use extreme care and reduce ground speed on slopes and rough ter-

rain.

 Watch for hidden hazards on the terrain during operation.

Pass diagonally through sharp dips and avoid sharp drops to prevent hanging

up tractor and mower.

Practice will improve your skills in maneuvering rough terrain.

MOWER REMOVAL & STORAGE

1.

Disengage tractor PTO and raise mower with the 3-point hitch.

2.

Disconnect mower driveshaft from tractor PTO.

3.

Collapse driveshaft as far as possible and store it in PTO hanger bracket

to prevent ground contact.

4.

Before extended storage, see page 14 for cleaning instructions.

5.

Place blocks under mower side skids. Lower mower onto blocks,

disconnect mower from tractor 3-point hitch, and carefully drive tractor

away from mower.

Figure 10

. Mower Storage Position

OWNER PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

___ Review and follow all safety rules and safety decal instructions on

pages 5 to 6.

___ Check that all safety decals are installed and in good condition.

Replace if damaged.

___ Check that all shields and guards are properly installed and in good

condition. Replace if damaged.

___ Check that chain shielding is in good condition and replace any dam-

aged chain links.

___ Check that all hardware and cotter pins are properly installed and

secured.

___ Check to ensure blades are sharp, in good condition, and installed cor-

rectly. Replace if damaged.

___ Check that equipment is properly and securely attached to tractor.

___ Make sure driveline spring-activated locking pin or collar slides freely

and is seated firmly in tractor PTO spline groove.

___ Make sure the driveline guards and tether chains are in good condition.

Guards must rotate freely on driveline. Fasten tether chains to the trac-

tor and the equipment as instructed.

___ Inspect area and remove stones, branches or other hard objects that

might be thrown, causing injury or damage.

___ Do not allow riders.

___ Check all lubrication points and grease as instructed in “Lubrication

Information” on page 12. Make sure the PTO slip joint is lubricated and

that the gearbox fluid levels are correct.

___ Set tractor PTO at 540 rpm.

___ Make sure tractor ROPS or ROPS cab and seat belt are in good condi-

tion. Keep seat belt securely fastened during operation.

___ Before starting engine, operator must be in tractor seat with seat belt

fastened. Place transmission in neutral or park, engage brake, and dis-

engage tractor PTO.

CM905A

12 Owner Service

MAN1260 (4/09/2018)

OWNER SERVICE

The information in this section is written for operators who possess basic

mechanical skills. If you need help, your dealer has trained service technicians

available. For your protection, read and follow the safety information in this

manual.

 Never allow children or untrained persons to operate equipment.

 Keep bystanders away from equipment.

 Before working underneath, carefully read Operator’s Manual

instructions, disconnect driveline, raise mower, securely block up all cor-

ners with jackstands, and check stability. Secure blocking prevents

equipment from dropping due to hydraulic leak down, hydraulic system

failures, or mechanical component failures.

 Keep all persons away from operator control area while performing

adjustments, service, or maintenance.

 Operate tractor PTO at 540 RPM. Do not exceed.

 Always wear relatively tight and belted clothing to avoid getting

caught in moving parts. Wear sturdy, rough-soled work shoes and protec-

tive equipment for eyes, hair, hands, hearing, and head; and respirator or

filter mask where appropriate.

BLOCKING METHOD

Do not work underneath mower unless it is properly attached to the tractor and

blocked securely. When properly attached, the unit will be anchored to mini-

mize front to rear movement.

Raise mower completely, set tractor brakes, turn engine off, remove key, block

tractor wheels front and rear, and disconnect mower driveline from tractor.

The only approved blocking device for this mower is a jackstand with a load rat-

ing of 454 kg (1000 lbs) or more. One jackstand under each corner of the

mower (four total) must be installed before working underneath.

When blocking, you must consider overall stability of the unit. Just blocking

under the unit will not ensure your safety. The working surface must be level

and solid to support the loaded weight of the jackstands. Test jackstands stabil-

ity before working under any portion of the mower.

Figure 11

. Blocking Method

LUBRICATION INFORMATION

Do not let excess grease collect on or around parts, particularly when operating

in sandy areas.

Figure 12 shows the lubrication points. The accompanying chart gives the fre-

quency of lubrication in operating hours, based on normal operating conditions.

Severe or unusual conditions may require more frequent lubrication. Some ref-

erence numbers have more than one location; be sure you lubricate all loca-

tions.

Use a lithium grease of #2 consistency with a MOLY (molybdenum disulfide)

additive for all locations. Be sure to clean fittings thoroughly before attaching

grease gun. When applied according to the lubrication chart, one good pump of

most guns is sufficient.

Fill blade spindles until grease purges out of the upper seal.

Use SAE 90W gear lube in the gearbox. Fill to plug on side of gearbox.

Check gearbox daily for evidence of leakage at both seals and the gasket

between the housing and cover. If leakage is noted, repair immediately. There

may be a small amount of lube emitted from the vent plug; this is not consid-

ered leakage.

Overfilling the gearbox will cause the excess gear lube to blow out vent plug

and ruin the belt.

Driveshaft Lubrication

Lubricate the driveshaft slip joint every 8 operating hours. Failure to maintain

proper lubrication could result in damage to U-joints, gearbox, and driveshaft.

1.

Lower mower to ground.

2.

Apply grease at three locations shown in Figure 12.

3.

Raise and lower mower several times to distribute grease.

Owner Service 13

MAN1260 (4/09/2018)

Figure 12

. Lubrication Points & Chart

BELT SERVICE

Belt Replacement

One of the major causes of belt failure is improper installation. Before installing

a new belt, check the following:

1.

Check pulley shafts and bearings for wear.

2.

Check pulley grooves for cleanliness.

3.

Make sure spindles turn freely and without wobble.

If grooves require cleaning, moisten a cloth with a non-flammable, non-toxic

degreasing agent or commercial detergent and water.

Avoid excessive force during installation. Do not use tools to pry belt into pulley

groove. Do not roll belt over pulleys to install. This can cause hidden damage

and premature belt failure.

Belt Installation

Figure 13.

Belt Routing

1.

Disconnect idler spring (H) from deck lug I.

2.

Slide belt under drive pulley A and over idler arm. Position belt around

drive pulley A.

3.

Loosen bolt holding belt guide G and swing it away from pulley B. Route

belt around pulley B, idler C and pulley D as shown.

4.

Make sure belt is on drive pulley A, route around idler F, and connect idler

spring to lug I on deck.

5.

Grasp belt between spindle pulley E, spring loaded idler F and spindle

pulley D. Pull spring loaded idler with belt to obtain enough belt length to

route it over pulley E. Make sure spring-loaded idler pivots freely with belt

installed.

NOTICE

■

Use care when installing or removing belt from spring-loaded

idler at step 5. Springs store energy when extended and, if released sud-

denly, can cause personal injury.

6.

Adjust belt guide G to provide 1.6 to 3.2 mm (1/16" to 1/8") clearance

from belt. Tighten bolt to 115 N-m (85 lbs-ft).

BLADE SERVICE

 Keep all persons away from operator control area while performing

adjustments, service, or maintenance.

REF

DESCRIPTION

FREQUENCY

1 Front U-Joint 8 Hours

2 Caster Wheel (Four wheels) 8 Hours

3 Caster Pivot (Four wheels) 8 Hours

4 Left Spindle (Access through hole) 24 Hours

5 Shield Bearings 8 Hours

6 Rear U-Joint 8 Hours

7 Gearbox (Fill to center of horizontal shaft with SAE 90W gear lube) Check Daily

8 Right Spindle (Access through hole) 24 Hours

9 Center Spindle (Access through hole) 24 Hours

10 Slip Joints 8 Hours

14 Owner Service

MAN1260 (4/09/2018)

Blade Installation

 Your dealer can supply genuine replacement blades. Substitute

blades may not meet original equipment specifications and may be dan-

gerous.

Figure 14

. Blade Assembly

1.

Place cap screws (3) through outer holes in blade and spindle shaft.

2.

Make sure blade cutting edge is positioned to lead in a clockwise

rotation, as viewed from top of mower.

3.

Place locknuts (4) on screws, torque to 114 N-m (84 lbs-ft).

Blade Sharpening

Figure 15.

Blade Sharpening

NOTICE

■

When sharpening blades, be sure to balance them. Unbalanced

blades will cause excessive vibration which can damage blade spindle

bearings. Vibration may also cause structural cracks in mower compo-

nents.

1.

Remove blades.

2.

Always sharpen both ends at the same time to maintain balance.

3.

Follow original sharpening pattern.

4.

Do not sharpen blade to a razor edge. Leave from .8 to 1.6 mm (1/32" to

1/16") blunt edge.

5.

Do not sharpen back side.

Chain Shielding

 Full chain or rubber shielding must be installed when operating in

populated areas or other areas where thrown objects could injure people

or damage property.

• If this machine is not equipped with full chain or rubber shielding,

operation must be stopped when anyone comes within 300 feet (92

m).

• This shielding is designed to reduce the risk of thrown objects.

The mower deck and protective devices cannot prevent all objects

from escaping the blade enclosure in every mowing condition.

It is

possible for objects to ricochet and escape, traveling as much as 300

feet (92 m).

Check that chain shielding is in good condition and replace any damaged chain

links.

CLEANING

After Each Use

●

Remove large debris such as clumps of dirt, grass, crop residue, etc.

from machine.

●

Inspect machine and replace worn or damaged parts.

●

Replace any safety decals that are missing or not readable.

Periodically or Before Extended Storage

●

Clean large debris such as clumps of dirt, grass, crop residue, etc. from

machine.

●

Remove the remainder using a low-pressure water spray.

1.

Be careful when spraying near scratched or torn safety decals or

near edges of decals as water spray can peel decal off surface.

2.

Be careful when spraying near chipped or scratched paint as water

spray can lift paint.

3.

If a pressure washer is used, follow the advice of the pressure

washer manufacturer.

●

Inspect machine and replace worn or damaged parts.

●

Sand down scratches and the edges of areas of missing paint and coat

with Woods spray paint of matching color (purchase from your Woods

dealer).

●

Replace any safety decals that are missing or not readable (supplied free

by your Woods dealer). See Safety Decals section for location drawing.

1. Spindle assembly

2. Blade

3. 1/2 NC x 1-1/2 HHCS

GR5

4. 1/2 NC Lock nut

Troubleshooting 15

MAN1260 (4/09/2018)

TROUBLE SHOOTING

MOWING CONDITIONS

BELT CONDITIONS

* Check belt for damage by laying it flat on the floor. A belt that does not lie flat (has humps or twists, indicating broken or stretched cords) must be replaced.

PROBLEM POSSIBLE CAUSE SOLUTION

Grass cut higher in center of swath than at

edge

Height of mower higher at front than at rear Adjust mower height and attitude so that mower rear

and front are within 12.7 mm (1/2") of same height.

See instructions on page 9.

Loose blade Check blade hardware.

Grass cut lower in center of swath than at

edge

Height of mower lower at front than at rear Adjust mower height and attitude so that mower rear

and front are within 12.7 mm (1/2") of same height.

See instructions on page 9.

Loose blade Check blade hardware

Streaking conditions in swath Conditions too wet for mowing Allow grass to dry before mowing.

Blades unable to cut that part of grass pressed

down by path of tractor tires

Slow ground speed of tractor but keep engine running

at full PTO rpm. Cutting lower will help. Adjust tractor

tire spacing if possible.

Dull blades Sharpen or replace blades.

Loose blade Check blade hardware.

Material discharges from mower unevenly;

bunches of material along swath

Material too high and too much material Reduce ground speed but maintain 540 rpm at tractor

PTO, or make two passes over material. Raise mower

for the first pass and lower for the second and cut at

90 degrees to first pass. Raise rear of mower high

enough to permit material to discharge, but not so high

that conditions listed above occur.

Grass wet Allow grass to dry before mowing. Slow ground speed

of tractor but keep engine running at full PTO rpm.

PROBLEM POSSIBLE CAUSE SOLUTION

Belt slippage Mower overloading; Material too tall or heavy Reduce tractor ground speed but maintain full PTO

rpm. Cut material twice, one high pass and then mow

at desired height. Cut at 90 degrees to first pass.

Oil on belt from over lubrication Be careful not to over lubricate. Clean lubricant from

belt and pulleys with clean rag. Replace oil-soaked

belt.

Belt hung up or rubbing Check belt position in pulleys and idlers. Check belt

for free travel in pulleys. Check under mower and

around blade spindle shaft for wire, rags, or other

foreign material. Clean all material from under mower.

Frayed edges on belt cover Belt misaligned Re-align belt. Be sure belt does not rub any other part

while running.

Pulley misaligned Inspect to ensure belt is running in center of backside

idler. Shim idler as necessary to align.

Belt rollover Pulley misaligned Re-align pulley.

Damaged belt Replace belt.*

Foreign object in pulley groove Inspect all pulley grooves for rust, paint, or weld spots

and remove.

Worn pulley groove Replace pulley.

Damaged belt Rollover, high shock loads or installation

damaged

Replace belt.*

Belt breakage High shock loads Avoid abusive mowing. Avoid hitting the ground or

large obstructions.

Belt came off drive Check pulleys for foreign material in grooves. Avoid

hitting solid objects or ground.

16 Dealer Service

MAN1260 (4/09/2018)

DEALER SERVICE

The information in this section is written for dealer service personnel. The

repair described here requires special skills and tools. If your shop is not prop-

erly equipped or your mechanics are not properly trained in this type of repair,

you may be time and money ahead to replace complete assemblies.

 Before working underneath, read manual instructions, securely

block up, and check stability. Secure blocking prevents equipment from

dropping due to hydraulic leak down, hydraulic system failure, or

mechanical component failure.

 Keep all persons away from operator control area while performing

adjustments, service, or maintenance.

 Always wear relatively tight and belted clothing to avoid getting

caught in moving parts. Wear sturdy, rough-soled work shoes and protec-

tive equipment for eyes, hair, hands, hearing, and head; and respirator or

filter mask where appropriate.

BLOCKING METHOD

See "Blocking Method" instructions on page 12.

BLADE SPINDLE SERVICE

Spindle repair requires special skills and tools. If your shop is not properly

equipped or your mechanics are not trained in this type of repair, you may be

time and money ahead to use a new spindle assembly.

For reference, the grease fitting is in the top of the spindle shaft.

Permatex

®

3D Aviation Form-A-Gasket or equivalent is recommended as a

sealant.

Spindle Removal

1.

Remove blade from spindle.

2.

Remove belt from pulleys.

3.

Remove jam nut (1) and washer (3) from top of spindle shaft, Figure 16.

4.

Disassemble split taper bushing (5) (located on top of pulley) by

removing the two bolts (2) and washers (4).

5.

Insert bolts (2) into the threaded holes of bushing flange.

6.

Tighten bolts alternately to remove split taper bushing.

7.

Remove pulley (6).

8.

Remove bolts (19) that attach spindle to mower frame and remove

spindle.

9.

Remove grease fitting (21) from top of shaft.

Figure 16.

Sheave and Blade Assembly

Spindle Disassembly

1.

Place spindle assembly in press and press shaft down through housing.

2.

Remove seals from housing.

Spindle Assembly

Refer to Figure 17.

Bearing cones and cups are designed to work together. It is important to posi-

tion them so bearing cone taper mates with cup taper.

1.

Lubricate new cups with a light oil. Place them in spindle housing so they

will mate with bearing cones. Cups and cones are a press fit to minimize

wear.

Seat cups securely with a press or place a large drift in the flat lip and

drive them into housing until cup seats against machined shoulder of

housing.

Remove bearing cups from housing by placing a punch in the slots

provided and driving them out. Alternate punch positions from side to

side. Take care to prevent housing damage.

2.

Place bottom bearing cone into spindle with taper positioned to mate with

cup.

Figure 17

. Spindle and Shaft Assembly

NOTICE

■

Improper positioning of seals can cause seal damage. An improp-

erly installed seal will leak and could cause bearing failure.

3.

Identify the open side of the seal containing the spring.

4.

Apply a thin coat of Permatex to the area of housing where seals seat.

5.

Install bottom seal with spring up toward center of housing.

6.

Place seal squarely on housing and select a piece of pipe or tubing with

an OD that will set on outside edge of seal. A tubing with an OD that is

too small will bow seal cage.

7.

Carefully press seal into housing, to prevent distortion to metal seal cage.

Bottom seal should seat firmly and squarely against machined shoulder

in housing.

8.

Make sure seal lip did not roll under. Distortion to seal cage or damage to

seal lip will cause seal to leak. Damaged seals must be replaced.

9.

Insert shaft and bearing through bottom of housing.

10.

Fill housing cavity with a medium grade grease.

11.

Install top bearing on shaft to mate with top cone.

12.

Apply a thin coat of Permatex to shaft area where sleeve will seat.

1. 7/8 NF Jam nut

2. 1/4 NC x 1 HHCS GR5

3. 23.6 x 42.2 mm

(.929 x 1.66) Lock washer

4. 1/4 Lock washer

5. Bushing, H 1 straight bore

w/key

6. Sheave, H 1 BK

19. 1/2 NF x 1-1/4

HHCS GR5

1. Grease fitting

2. Seal, 38.1 x 54.0 x 7.9 mm

(1.50 x 2.12 x .31")

3. Sleeve, 29.0 x 38.1 x 14.0

mm (1.14 x 1.50 x .55")

4. Bearing, cone

5. Bearing, cup

6. Spindle, housing

7. Shaft, blade spindle

Dealer Service 17

MAN1260 (4/09/2018)

13.

Install sleeve on shaft and press sleeve and bearing into housing until all

free play is removed and there is a very light drag on bearings (similar to

adjusting front wheel bearings on an automobile). Check by spinning

spindle. It should turn freely.

14.

Be careful not to over tighten bearings. Proper bearing adjustment is

essential to good bearing life.

15.

If you over tighten bearings, hold spindle housing and rap spindle shaft

with a lead hammer.

16.

Carefully press top seal in with spring up. Top seal should be flush with or

to within 1.6 mm (1/16") above the housing.

17.

Rotate housing on spindle shaft, checking for free movement.

18.

Install grease fitting in spindle shaft.

Spindle Installation

NOTICE

■

Pulley installation sequence is very important for bearing life. Fol-

low the sequence exactly.

1.

Install spindle through bottom of mower and secure with four mounting

bolts.

2.

Install pulley and split taper bushing with integral key on spindle shaft.

Make sure bushing is in contact with sleeve on spindle shaft.

3.

Alternately tighten split taper bushing cap screws to 12 lbs-ft.

4.

Install toothed lock washer and nut on spindle shaft. Tighten nut until

snug. Bend up edge of lock washer against a flat side on nut.

GEARBOX REPAIR

Read this entire section before starting any repair. Many steps are dependent

on each other.

Repair to this gearbox is limited to replacing bearings, seals, and gaskets.

Replacing gears, shafts, and a housing is not cost effective. It is more econom-

ical to purchase a complete gearbox if repair to anything other than replace-

ment of bearings, seals or gaskets is required.

Fill gearbox with SAE 80W or 90W gear lube until it runs out the side level plug.

Inspect gearbox for leakage and bad bearings.

Leakage is a very serious problem and must be corrected immediately.

Bearing failure is indicated by excessive noise and side to side or end play in

gear shafts.

Gearbox Removal from Mower

Figure 18.

Gearbox Stand Assembly

1.

Disconnect and remove the rear driveline from the gearbox.

2.

Remove vent plug (10) and siphon gear lube from housing through this

opening.

3.

Remove gearbox stand (2) from mower deck by removing four flanged

lock nuts (6).

4.

Remove drive shield from gearbox.

5.

Remove castle nut (13) and hardware from output shaft of gearbox.

6.

Remove sheave (1) from gearbox.

7.

Remove four bolts (8) that attach gearbox to gearbox stand and remove

gearbox.

Seal Replacement

Recommended sealant for gearbox repair is Permatex® Aviation 3D Form-A-

Gasket or equivalent.

Leakage can occur at the vertical or horizontal gaskets and shaft seals.

Leakage at the horizontal gasket or seal can be repaired without removing the

gearbox from the cutter.

Seal Installation

Figure 19

. Seal Installation

NOTE: Proper seal installation is important. An improperly installed

seal will leak.

1.

Clean area in housing where seal outer diameter (OD) seats.

Apply a thin coat of Permatex.

2.

Inspect area of shaft where seal seats. Remove any burrs or

nicks with an emery cloth.

3.

Lubricate gear shaft and seal lips.

4.

Place seal squarely on housing, spring-loaded lip toward

housing. Select a piece of pipe or tubing with an OD that will sit

on the outside edge of the seal but will clear the housing. Tubing

with an OD that is too small will bow seal cage and ruin seal.

5.

Carefully press seal into housing, avoiding distortion to the

metal seal cage.

Gearbox Disassembly (Figure 20)

1.

Remove top cover (22) from housing. Turn gearbox upside down and

pour out remaining gear oil from gearbox.

2.

Remove oil cap (20) (to be replaced).

3.

Remove snap ring (10) and shim (13) from input shaft (3).

4.

Support gearbox in hand press and push on input shaft (3) to remove

bearing (7).

5.

Remove gear (1) from inside housing.

1. Sheave, offset 13.25

2. Gearbox stand

6. Nut, flanged lock 1/2 NC

7. Nut, flanged lock 5/8 NC

8. Screw, HHCS 5/8 NC x 1-

3/4

10. Vent plug

1. Seal

2. Pipe or tube

3. Seal seat

4. Casting

Pipe or tube must

press at outer

edge of

seal

Incorrect

Installation

18 Dealer Service

MAN1260 (4/09/2018)

6.

Remove oil seal (19) from front of housing (to be replaced).

7.

Remove snap ring (10) and shim (13) from front of housing (2).

8.

Remove input bearing (7) by using a punch and hammer from outside of

housing.

9.

Support housing in vise in a horizontal position.

10.

The castle nut (15) and cotter pin (25) are already removed with the drive

sheave. Remove snap ring (21), washer (8), and seal (18).

11.

Remove cotter pin (9), castle nut (14), and washer (17) from output shaft

(4).

12.

Remove output shaft (4) by using a punch and hammer and tap on top to

drive down.

13.

Remove gear (5) and shim (16) from inside housing.

14.

Remove bearing (26) by using a punch and hammer from the top, outside

the housing.

15.

Support housing upside down (top cover surface) and remove bearing (6)

by using a punch and hammer from the bottom side of the housing.

16.

Inspect gears for broken teeth and wear. Some wear is normal and will

show on loaded side. Forged gear surfaces are rough when new. Check

that wear pattern is smooth.

17.

Inspect vertical and horizontal shafts for grooves, nicks, or bumps in the

areas where the seals seat. Resurface any damage with emery cloth.

18.

Inspect housing and caps for cracks or other damage.

.

Figure 20

. Gearbox Assembly

Vertical Shaft Seal Replacement

1.

Disconnect and remove the driveline from the gearbox.

2.

Remove vent plug (24). Figure 20, and siphon gear lube from housing

through this opening.

3.

Remove gearbox stand from mower deck.

4.

Remove gearbox and pulley from gearbox stand.

5.

Remove vertical shaft seal (18). Replace with new seal (see Seal

Replacement, page 17).

Vertical seal should be recessed in housing.

NOTE:

Distortion to seal cage or damage to seal lip will cause seal to

leak.

6.

Fill gearbox with SAE 80W or 90W gear lube until it runs out the level

plug.

7.

Assemble gearbox and pulley to gearbox stand. Attach gearbox stand to

mower deck.

Horizontal Shaft Seal Replacement

1.

Disconnect and remove the driveline from the gearbox.

2.

Remove vent plug (24), Figure 20, and siphon gear lube from housing

through this opening.

3.

If the leak occurred at either end of horizontal shaft, remove oil cap (20)

and/or oil seal (19). Replace with new one (see Seal Replacement, page

17).

Horizontal seal should be pressed flush with outside of housing.

4.

Fill gearbox with SAE 80W or 90W gear lube until it runs out the level

plug

Gearbox Reassembly

Refer to Figure 20.

NOTE: Repair to this gearbox is limited to replacing bearings, seals, and gas-

kets. Replacing gears, shafts, and a housing is not cost effective. Purchasing a

complete gearbox is more economical.

1.

Clean housing, paying specific attention to areas where gaskets will be

installed.

2.

Wash housing and all components thoroughly. Select a clean area for

gearbox assembly. Replace all seals, bearings, and gaskets. All parts

must be clean and lightly oiled before reassembling.

3.

Insert output bearings (6 & 26) in the housing, using a round tube of the

correct diameter and a hand press.

4.

Slide output shaft (4) through both bearings (6 & 26) until it rests against

bearing (6).

5.

Slide shim (16) over output shaft (4).

1. Crown gear

2. Gearbox housing

3. Input shaft

4. Output shaft

5. Gear pinion

6. Bearing

7. Bearing

8. Protective flat washer

9. Cotter pin

10. Snap ring

11. Snap ring

12. Spacer

13. Shim

14. Castle nut

15. Castle nut M24 x 2

16. Shim

17. Flat washer

18. Oil seal (40 x 80 x 12 mm)

19. Oil seal (35 x 72 x 10 mm)

20. Cap

21. Snap ring

22. Top cover

23. Bolt M8 x 14 mm

24. Breather level plug

25. Cotter pin

26. Bearing

27. Ball bearing

Dealer Service 19

MAN1260 (4/09/2018)

6.

Press gear (5) onto output shaft (4) and secure with washer (17), castle

nut (14), and cotter pin (9).

7.

Apply grease to lower seal lips (18) and press seal over output shaft (4),

using a tube of the correct diameter. Be sure not to damage the seal lip.

Press in housing so that seal is recessed.

8.

Insert protective washer (8) by hand. Install snap ring (21) and position it

together with dual lip seal (18) by pressing it into position. Verify that

snap ring is seated correctly.

9.

Press bearing (7) into the housing, using a round tube of the correct

diameter and a hand press. Secure with shim (13) and snap ring (10).

10.

Secure snap ring (11) on input shaft (3) if not already secure.

11.

Place gear (1) through top of housing and align gear (1) and gear (5) so

that gear teeth are a match.

12.

While holding gear (1) in place, slide input shaft (3) through gear (1) and

bearing (7). Align splines on shaft (3) and gear (1).

13.

Slide spacer (12) over input shaft (3) and press bearing onto input shaft

(3), using a round tube of the correct diameter and a hand press.

14.

Slide shim (13) over input shaft (3) and secure with snap ring (10).

15.

Check input shaft end float by moving the input shaft (3) by hand. If end

float is higher than .3 mm (0.012”), insert shim between input shaft (3)

and rear bearing (7). Repeat until end float is less than .3 mm (0.012”).

Check rotational torque by hand. The torque should be less than .25 N-m

(2.2 lbs-inch).

16.

Check that the gear backlash is between .15 mm (0.006”) and .41 mm

(0.016”). You should not have to adjust the backlash.

17.

Press in input oil seal (19), using tube of correct diameter. Be careful not

to damage seal lip.

18.

Press oil cap (20) on to cover the rear of housing, using a tube of the

correct diameter.

19.

Check gearbox housing for leaks by plugging all holes except one. Apply

27.6 kPa (4 psi) compressed air and immerse the gearbox in water to

verify that there are no leaks.

20.

Remove gearbox from water and dry off with compressed air. Add SAE

80W or 90W EP oil until it runs out of side level hole. Tighten all plugs.

Gearbox Installation

NOTE:

Gearbox is heavy: do not attempt to move without mechanical assis-

tance.

1.

Set gearbox on gearbox stand and fasten with bolts and nuts. Torque

bolts to 237 N-m (175 lbs-ft).

2.

Attach drive sheave to output shaft. Secure using castle nut and

hardware previously removed.

3.

Attach gearbox stand to mower using four flanged 1/2" lock nuts.

DRIVE SHEAVE INSTALLATION

1.

When gear stand is installed on mower, dimension A (from the top of the

mower deck to the center line of the drive pulley) must be 61.9 ±.8 mm

(2-7/16" ±1/32"). This is a critical dimension and must be carefully

adjusted for proper belt life. Add or subtract shim washers under idler

pulley (3) to align with drive pulley (4).

2.

Tighten gear stand hardware.

3.

Fill gearbox half full with SAE 90W gear lube.

4.

Check level after waiting five minutes to permit lube to work through

bearings. Add lube, if necessary, until gearbox is half full.

5.

Replace driveline shield. Attach driveline to gearbox.

Figure 21

. Drive Sheave Installation

UNIVERSAL JOINT REPAIR

Figure 22

. U-Joint Exploded View

U-Joint Disassembly

1.

Remove external snap rings from yokes in four locations as shown in

Figure 23.

1. Shim

2. Idler arm

3. Idler pulley

4. Drive sheave

5. Castle nut & cotter pin

6. Gearbox stand

1. Yoke

2. Cup and bearings

3. Snap ring

4. Journal cross

20 Dealer Service

MAN1260 (4/09/2018)

.

Figure 23

2.

With snap rings removed, support drive in vise, hold yoke in hand and tap

on yoke to drive cup up out of yoke. See Figure 24.

Figure 24

3.

Clamp cup in vise as shown in Figure 25 and tap on yoke to completely

remove cup from yoke. Repeat Step 2 and Step 3 for opposite cup.

Figure 25

4.

Place universal cross in vise as shown in Figure 26 and tap on yoke to

remove cup. Repeat Step 3 for final removal. Drive remaining cup out

with a drift and hammer.

Figure 26

U-Joint Assembly

1.

Place seals securely on bearing cups. Insert cup into yoke from outside

and press in with hand pressure as far as possible. Insert journal cross

into bearing cup with grease fitting away from shaft. Be careful not to

disturb needle bearings. Insert another bearing cup directly across from

first cup and press in as far as possible with hand pressure.

2.

Trap cups in vise and apply pressure. Be sure journal cross is started into

bearings and continue pressure with vise, squeezing in as far as

possible. Tapping the yoke will help.

3.

Seat cups by placing a drift or socket (slightly smaller than the cup) on

cup and rap with a hammer. See Figure 27. Install snap ring and repeat

on opposite cup.

4.

Repeat Step 1 & Step 2 to install remaining cups in remaining yoke.

5.

Move both yokes in all directions to check for free movement. If

movement is restricted, rap on yokes sharply with a hammer to relieve

any tension. Repeat until both yokes move in all directions without

restriction.

Figure 27

La pagina si sta caricando...

Woods PRD8400E Manuale utente

Questo manuale è adatto anche per

Woods PRD8400E Manuale utente

in altre lingue

Documenti correlati

Altri documenti