54
08. Secure head with one hand, rotate the
blue fastening ring at the base of the
head clockwise until tight.
09. Grasp the OtoClear Tip (as shown)
and twist onto the luer lock fitting
of the adapter until it stops.
Bionix SprayWash Bottle Use Instructions:
01. Assure that the temperature gauge reads “OK” before continuing.
02. This is to indicate that the water is approximately body temperature.
03. DO NOT use cold or hot water as it may cause dizziness in
some patients.
04. Prime the unit by discharging into a sink.
05. Insert the OtoClear tip fully into the ear canal. The flared design of
the OtoClear Tip protects against over-insertion. Tip: Fully inserting
the OtoClear Tip will help eliminate backsplash.
06. Place a basin beneath the outer ear to capture draining effluent.
Note: The OtoClear Tip directs water towards the walls of the ear
canal creating a turbulent lavage that effectively dislodges cerumen.
The Exit portals control backsplash and deliver the effluent into the basin.
07. Reexamine the ear canal. Repeat the irrigation procedure as needed.
Sometimes a large plug of wax will not exit through the portal. In these cases,
we recommend the use of a Safe Ear Curette™ or Lighted Ear Curette™ to
extract any remaining cerumen.
08. Remove any remaining water in the ear canal with an absorbent sponge.
When procedure is complete, remove and dispose of the single-use OtoClear Tip.
WARNING: Failure to remove the OtoClear Tip runs the risk of
cross contamination between patients. The tip is designed to be a sin-
gle-use product.
Cleaning the Bionix OtoClear SprayWash Bottle:
It is recommended to clean the Bionix SprayWash bottle daily following the proce-
dure below.
01. Prepare a solution of dishwashing liquid and water.
02. Ensure the SprayWash bottle and spray head are completely drained of water.
03. Wash the outside of the bottle and spray head with the dishwashing solution.
04. Fill the bottle with the dishwashing solution and reattach the spray head.
05. Shake the SprayWash bottle and pump until soapy water discharges.
06. Rinse the outside of the SprayWash bottle with water until all suds is removed.
07. Remove the spray head from the bottle and empty the dishwashing solution
from the bottle.
08. Rinse and refill the bottle with water, repeat until no suds is visible in the bot-
tle’s rinse water.
09. Refill the bottle with water and reattach the spray head.
10. Pump the spray head until no suds is evident in the discharged rinse water.
11. Remove the spray head from the bottle.
12. Pump the spray head until all water is discharged.
13. Drain all water from the bottle.
14. Dry the outer surfaces of the bottle & spray head and leave them separated to
allow complete drying.
15. Clean the ear basin using the same solution. Rinse thoroughly and dry.
High Level Disinfection of the Bionix OtoClear SprayWash Bottle:
It is recommended to high level disinfect the Bionix SprayWash Bottle after any
use where there was contact with blood, infectious material, or non-intact skin.
01. Use one of the following high level disinfecting (HLD) solutions that are com-
patible with the Bionix SprayWash Bottle:
• Ortho-Phthalaldehyde Solution (0.55% maximum)
• Accelerated Hydrogen Peroxide Solution (2% maximum)
• Glutaraldehyde Solution (3.0% maximum)
02. Prepare the HLD solution per the manufacturer’s instructions.
03. Remove the spray head from the bottle.
04. Ensure all water has been drained from the bottle and the spray head.
05. Fill the SprayWash bottle with the HLD solution and reattach the spray head.
06. Pump the SprayWash bottle until HLD solution discharges.
07. Remove the spray head and completely fill the bottle with HLD solution.
08. Reattach the spray head.
09. Allow the HLD solution to soak in the Bionix SprayWash Bottle per the HLD
manufacturer’s instructions for use.
10. After the manufacturer’s recommended soak, remove the spray head from the
bottle and empty the HLD solution from the bottle.
11. Thoroughly rinse the outer surfaces of the bottle and spray head with water.
12. Fill the bottle with clean rinse water and reattach the spray head.
13. Pump until half of the bottle is discharged.
14. Repeat steps 11 – 13 until the bottle has been rinsed three times.
15. Remove the spray head from the bottle.
16. Drain all water from the bottle.
17. Pump the spray head until all water is discharged.
18. Dry the outer surfaces of the bottle and spray head and leave them separated
to allow complete drying.
19. To high level disinfect the ear basin, repeat steps 1 & 2 and follow the
manufacturer’s instructions.