Sanyo CLT-A5832 Manuale utente

Marca: Sanyo

Modello: CLT-A5832

Categoria: Telefoni

Tipo: Manuale utente

Questo manuale è adatto anche per

5.8 GHz

Cordless Telephone

with Caller ID &

Visual Call Waiting

INSTRUCTION MANUAL

CLT-A5830

Dual Handset Models

CLT-A5822

CLT-A5832

Important

Charge the handset battery for 12 continuous hours prior to first

use.

The picture depicts dual handset model

SANYO Canada Inc.

www.sanyo.ca

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:521

INTRODUCTION ................................................................................................. 4

GETTING STARTED ......................................................................................... 5

Checking package contents ................................................................................ 5

Modular jack ................................................................................................... 5

Installation tips ............................................................................................... 5

Battery setup ................................................................................................. 6

Connecting the base unit and charging the handset ....................................... 6

Connecting the charger and charging the handset ...........................................

(For CLT-A5822 and CLT-A5832 ) .................................................................. 6

Telephone line connection .............................................................................. 7

Tone/pulse setting .......................................................................................... 7

To register the second handset (For CLT-A5822 and CLT-A5832 ) ................. 7

NAMES AND CONTROLS ................................................................................ 8

Handset ................................................................................................ 8

Base unit and Charger ...................................................................................9

INITIAL PROGRAMMING ................................................................................ 10

Language setting ......................................................................................... 10

Area code setting ........................................................................................ 10

Ringer tone .................................................................................................. 10

Tone/pulse setting ........................................................................................ 10

Resetting to default ...................................................................................... 11

BASICS ........................................................................................................... 11

Receiving a call ........................................................................................... 11

Making a call ................................................................................................ 12

Volume adjustment ....................................................................................... 12

Transferring a call (For CLT-A5822 and CLT-A5832) .................................... 12

Ringer switch .............................................................................................. 12

Pre-dialing ................................................................................................... 13

Changing the pre-dial number ...................................................................... 13

Redialing ...................................................................................................... 13

Fast redialing .............................................................................................. 13

FLASH key .................................................................................................. 13

CH (Channel)/DEL key .................................................................................. 13

* TONE key .................................................................................................. 14

Handset locator (paging function) ................................................................ 14

MUTE key ................................................................................................... 14

TABLE OF CONTENTS

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:522

Low battery warning ................................................................................... 14

Voice mail indicator ...................................................................................... 15

CALLER ID FEATURES ................................................................................. 15

Caller ID with Call Waiting ............................................................................. 15

Caller ID list .................................................................................................. 16

Reviewing Caller ID list ................................................................................. 16

Formatting Caller ID numbers ........................................................................ 16

Storing Caller ID entries in the directory ........................................................ 17

Dialing a Caller ID number ............................................................................. 17

Deleting entries from the Caller list ............................................................... 17

Deleting the displayed entry ......................................................................... 17

Deleting all entries ........................................................................................ 18

DIRECTORY ..................................................................................................... 18

Storing a number in the directory ................................................................. 18

Replacing a directory entry with a Caller ID entry.......................................... 19

Changing a stored number ........................................................................... 19

Making calls from the directory .................................................................... 19

Reviewing and deleting directory contents .................................................. 19

Chain dialing from the directory .................................................................... 20

CHANGING THE BATTERY ........................................................................... 20

RECYCLING NICKEL- METAL HYDRIDE BATTERIES .................................. 21

POWER FAILURE .......................................................................................... 21

HEADSET JACK AND BELT CLIP ................................................................ 22

LIGHT SIGNALS ............................................................................................. 22

LCD SCREEN MESSAGES ............................................................................ 23

SOUND SIGNALS ........................................................................................... 24

TROUBLESHOOTING ....................................................................................... 24

MAINTENANCE ............................................................................................... 28

MAXIMIZE BATTERY PERFORMANCE ......................................................... 29

TECHNICAL INFORMATION .......................................................................... 30

SANYO COMFORT WARRANTY .................................................................... 32

SOS HELP LINE ............................................................................................. 34

TABLE OF CONTENTS

The exclamation point within the triangle is a warning sign alerting

you of important instructions accompanying the product.

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:523

Congratulations on your purchase of this SANYO cordless telephone.

Your SANYO 5.8 GHz cordless telephone is a fine-quality home communications

product. It is carefully designed and produced by a world leader of consumer and

industrial electronic equipment. With proper maintenance and care, it will provide

you with years of enjoyment and convenience.

Main Features

5.8 GHz Technology

Superior Range – The use of 5.8 GHz frequency band for signal transmission

between base and handset means greater communication range compared to

conventional 43 - 49 MHz cordless telephones.

Ultra-Low Noise – The high frequency communication also has significantly

reduced noise level.

40-Channel Auto Scan – Your new telephone uses one of 40 channels in the

5.8-GHz frequency band. It automatically selects a clear channel every time you

receive or place a call on the handset.

Other features

IMPORTANT: To use all of the features of this telephone, you must subscribe to

either the standard Name/Number Caller ID Service or Caller ID with Call Waiting

Service from your telephone company. To know who is calling while you are on

the phone, you must subscribe to Caller ID with Call Waiting Service.

• Caller ID on handset

• Compatible with Caller ID and

Visual Call Waiting

• 40 name/number Caller ID list:

name/number, time and date

• 3-line trilingual display with backlight

LCD screen

• Dial back from Caller ID list

• 3 ringer tones

• 10 memory call log

• Tone & pulse dialing compatible

• Caller transfer (For CLT-A5822 and

CLT-A5832 only)

INTRODUCTION

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:524

Modular jack

You need an RJ11 type modular phone jack. If you do not have a modular jack, call

your local phone company to find out how to get one installed.

Checking package contents

Make sure your package includes the items shown here.

GETTING STARTED

Installation tips

Some cordless telephones operate at frequencies that may cause interference

to nearby TVs, microwave ovens, and VCRs. To minimize or prevent such

interference, the base of the cordless telephone should not be placed near or on

top of a TV, microwave oven, or VCR. If such interference continues, move the

cordless telephone farther away from these appliances.

Certain other communications devices may also use the 5.8 GHz frequency for

communication and if not set properly these devices may interfere with each

other and/or your new telephone. If you are concerned with interference, please

refer to the owner’s manual for these devices on how to properly set channels

to avoid interference. Typical devices that may use the 5.8 GHz frequency for

communication include wireless audio/video senders, wireless computer

networks, multi-handset cordless telephone systems, and some long-range

cordless telephone systems.

2 X AC Adaptors

(CLT-A5830 with

one adaptor)

For Base:

U090030D1201

For Charger:

U090020D12

Telephone

line cord

2 X Handsets

(CLT-A5830 with

one handset)

2 X Belt clips

(CLT-A5830 with

one belt clip)

Base unit

Charger

(For CLT-A5822

and CLT-A5832)

2 X batteries

(CLT-A5830 with

one battery)

Battery order

form

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:525

Battery setup

1. Remove the battery compartment cover on the handset, insert the battery,

plug the cord into the jack (inside the compartment) and replace the cover.

2. Set the handset RINGER switch to ON, and place handset in the base.

Slide down the

battery cover

Place the battery

in the slot

Plug the wire

into the jack

Slide up the

battery cover

Connecting the base unit and charging the handset

1. Plug the AC adaptor into the power DC 9V

jack on the back of the base. Plug the other

end into a wall outlet.

2. Set the base on a desk or tabletop and place

one handset in the base unit.

3. Make sure that the CHARGE/IN USE LED

illuminates.

Connecting the charger and charging the handset

(For CLT-A5822 and CLT-A5832)

1. Plug the AC adaptor into the power DC 9V jack

on the back of the charger. Plug the other end

into a wall outlet.

2. Place another handset in the charger and make

sure that the CHARGE LED illuminates.

Note: • Charge your handset at least 12

hours before plugging into the

phone line.

• Charge the handset for 12 continuous hours prior to first use. The

initial battery charge is important for best performance.

• It is normal for the handset and base to get warm when the

handset is charging in the base.

Caution: Use only the SANYO AC adaptor that is supplied with this

phone. Using another AC adaptor may damage the phone.

GETTING STARTED

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:526

Tone/pulse setting

1. If you have Pulse (rotary) service, you will need to set the dial mode to pulse.

If you have Touch-Tone service, do nothing as your phone has been set to

Tone prior to shipment. If you do not know which type of service you have,

contact your local telephone company.

2. To change to Pulse or Tone service, See Tone/pulse setting, page 10.

Telephone line connection

Once the handset battery is fully charged, connect the telephone line cord to the

TEL LINE jack on the back of the base. Plug the other end into a telephone outlet.

Your cordless phone uses a digital security system to provide protection

against false ringing, unauthorized access and charges to your phone

line. When you place the handset in the main base, the handset will

automatically register to the base.

To register the second handset for CLT-A5822 and CLT-A5832

The second handset (charge in the extra charging cradle) must also be registered

to the main base before use.

1. Be sure both handsets are fully charged.

2. Remove the handset from the charging cradle, and place it in the main base.

3. Wait for at least 5 seconds before removing the handset from the main base.

4. After both handsets are registered, it doesn’t matter which handset is placed

in the main base or the charger.

5. The charge/in use LED lights on the main base.

Note: • After a power failure occurs or battery replacement, both handsets will

need to be re-registered. To re-register, follow the same registration

process as above.

• If the handset’s battery becomes very low, the handset must be

recharged for 12 hours and re-registered to the main base unit.

GETTING STARTED

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:527

Handset

NAMES AND CONTROLS

1. Belt clip

2. REDIAL key

3. Headset jack

4. * TONE/EXIT key

5. MEM (memory) key

6. CH (channel)/DEL key

7. Charging contacts

8. Incoming call/in use LED

9. Earpiece

10. LCD screen

11. TALK key (also used to end a call)

12. MUTE/FORMAT key

(MUTE/FORMAT/TRANSFER key)

13. Ringer switch

14. CID/VOL (volume) up/down key

15. Keypad (0-9)

16. # PAUSE key

17. FLASH/PROG (program) key

18. Microphone

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:528

Base Unit

NAMES AND CONTROLS

Charger (For CLT-A5822 and CLT-A5832)

1. Handset Cradle

2. Page Key

3. Charge/In Use LED

4. Charge LED

5. Charging contacts

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:529

Before using this telephone, 4 initial settings must be completed on the handset:

Language, Area code (this is required to use Caller ID service from your tele-

phone company), Ringer tone, and Tone/Pulse setting.

Language setting

1. Make sure the phone is OFF (not in TALK mode).

2. Press FLASH/PROG until “ 1 ENG 2 FRA 3 ESP ” shows on screen.

3. Press CID/VOL

or , or the number keys (1 – 3) to select the desired

language.

4. Press FLASH/PROG to store selection. You will hear a confirmation tone.

Area code setting

For proper Caller ID operation, you must program your area code.

1. Make sure the phone is OFF (not in TALK mode).

2. Press FLASH/PROG repeatedly until “AREA CODE - - - ” shows on screen.

3. Enter your 3-digit area code using the number keys. To change a digit, press

CH/DEL and then re-enter the number.

4. Press FLASH/PROG to store selection. You will hear a confirmation tone.

Ringer tone

1. Make sure the phone is OFF (not in TALK mode).

2. Press FLASH/PROG repeatedly until “RINGER TONE 1” shows on screen.

3. Press CID/VOL

or , or press the number keys 1-3 to select the desired

ringer tone.

4. Press FLASH/PROG to store selection. You will hear a confirmation tone.

Tone/pulse setting

1. Make sure the phone is off (not in TALK mode).

2. Press FLASH/PROG repeatedly until “ 1TONE 2 PULSE ” shows on

screen.

3. Press CID/VOL

or , or press the number keys 1-2 to select TONE or

PULSE.

4. Press FLASH/PROG to store selection. You will hear a confirmation tone.

INITIAL PROGRAMMING

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5210

Resetting to default

You can reset the phone programming to the initial factory default settings. The

default settings are:

Language English

Area Code - - -

Ringer Tone 1

Tone/Pulse Setting Tone

1. Make sure the phone is OFF (not in TALK mode).

2. Press FLASH/PROG repeatedly until “DEFAULT 1 NO” shows on screen.

3. Press CID

or , or the 1 or 2 keys to select your choice between “1 NO”

and “2 YES” for Default Settings”

4. Press FLASH/PROG again to confirm. You will hear a confirmation tone.

Receiving a call

When receiving an incoming call, the LED on the handset flashes, and the handset

will show caller information. *

* Note: A subscription is required from your local phone company to receive

Caller ID information on your phone. See Caller ID Features, page 15.

1. Press TALK to answer the call.

Note: If handset is in the base cradle, remove it from base before pressing

the TALK key. Either handset 1 or handset 2 can answer the call at once.

(for CLT-A5822 and CLT-A5832)

2. Press TALK to end your call.

Note: If you replace the handset to the base cradle or charger cradle (for

CLT-A5822 and CLT-A5832), the handset automatically hangs up.

BASICS

INITIAL PROGRAMMING

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5211

Making a call

1. Press TALK.

Note: If handset is in the base cradle, remove it from base before pressing

the TALK key.

2. Dial the phone number.

3. Press TALK to end your call.

Volume adjustment

The VOLUME key adjusts the volume level of the earpiece. There are 4 volume

levels.

1. Make sure the phone is in TALK mode.

2. Press the CID/VOL

or key on the handset.

Transferring a call (For CLT-A5822 and CLT-A5832)

The current conversation can be transferred to another handset. Only one

handset can talk with an outside caller at a time. The second handset cannot

listen to the conversation or make an outgoing call while the other handset is in

use.

1. During a call, press and hold the MUTE/FORMAT key, until “TRANSFERRING”

shows on the screen and both handsets beep.

Note: To cancel the transfer and return to the caller, press TALK key on the

handset.

2. Press TALK on the other handset to get the call.

Note: During call transfer, if there is no further action within 2 minutes on both

handsets, the call will end.

Ringer switch

The RINGER switch must be on for the handset to ring during incoming calls.

Telephone Number

BASICS

Channel No.

Call Timer

Volume Level

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5212

Pre-dialing (up to 32 digits)

1. Make sure the phone is OFF (not in TALK mode).

2. Enter the telephone number. The number is displayed as you enter it.

3. Press TALK.

Note: Pressing *TONE will exit pre-dialing.

Changing the pre-dial number

1. Make sure the phone is OFF.

2. Enter the telephone number.

3. Press CH/DEL to delete digits one by one.

4. Re-enter the number.

Redialing

1. Make sure the phone is OFF.

2. Press TALK.

3. Press REDIAL to redial the last number (up to 32 digits).

Fast redialing

1. Press TALK, (if you are not already in TALK mode).

2. Enter the telephone number you want to dial.

3. If the line is busy, press REDIAL. The phone will drop the line for two

seconds and redial again.

FLASH key

Use the FLASH/PROG key to activate custom calling services such as Call

Waiting.

Tip: Do not use TALK to activate custom calling services such as Call Waiting,

or you will hang up the phone.

CH (Channel)/DEL key

While talking, you might need to manually change the channel to get rid of static.

Press the CH/DEL key to switch to a clear channel.

BASICS

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5213

* TONE key

This feature enables Pulse service phone users to access touch-tone services

offered by banks, credit card companies, etc.

1. Dial the desired number.

2. Press *TONE after your call is answered.

3. Follow the voice instructions to complete your desired action.

4. Hang up when finished. The phone returns to Pulse service.

Handset locator (Paging function)

This feature helps to locate a misplaced handset.

1. Press PAGE on the base, the screen shows “PAGING”. The handset beeps

continuously for about 2 minutes or until you press any key on the handset.

2. To stop the paging, do one of the following:

• Press PAGE on the base.

• Press TALK to enter talk mode.

• Press any button on the handset.

Note: You can still page the handset with the ringer off.

MUTE key

To have a private, off-line conversation, use the MUTE feature. The caller on the

other end of the line cannot hear you, but you can still hear them.

To mute the microphone:

1. Press MUTE/FORMAT in TALK mode. The screen shows “MUTE”.

2. Press MUTE/FORMAT again to return to your phone conversation.

Low battery warning

1. If the battery is low and the phone is in TALK mode, a warning tone

consisting of 2 short beeps will sound from the handset and the LED will

flash every 15 seconds. “LOW BATTERY” shows on screen.

2. If the battery is low and the phone is in STANDBY mode, the LED on handset

will flash every 15 seconds, and “LOW BATTERY” shows on screen.

BASICS

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5214

This phone receives and displays incoming call information transmitted by your

local phone company, provided you subscribe to Caller ID, and/or Call Waiting

services. This information can include the phone number and/or the name, date

and time. The phone can store up to 40 calls for later review.

Caller ID with Call Waiting

When you subscribe to Caller ID with Call Waiting (Visual Call Waiting

) service

from your phone company, you are able to see who is calling when you hear the

Call Waiting beep. Caller identification information appears on screen after you

hear the beep.

Press the FLASH/PROG key to put the current call on hold so that you can

answer the incoming call. The following information will display.

To return to the first call, press FLASH/PROG again.

IMPORTANT: To use these features you must subscribe to Caller ID with Call

Waiting Service.

CALLER ID FEATURES

Voice mail indicator

When you subscribe to a voice mail service offered by your phone company, the

phone alerts you when voice mail has been received. MESSAGE WAITING

appears on screen for 60 seconds when a voice mail is received. The LED on the

base flashes to indicate there is a voice mail waiting. After the voice mail has

been reviewed, MSG WAITING OFF appears on screen, and the indicator stops

flashing.

Note: The indicator does not work with your answering machine. The phone will

only work with an FSK type of VMWI System. It will not work with the Stutter Dial

Tone type of VMWI System.

BASICS

Call No.

Call Timer

Caller Name

Telephone Number

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5215

Caller ID list

The incoming caller information transmitted from the phone company is received

by your phone between the first and second ring and stored in the Caller ID list. If

you answer a call before the second ring the caller information may not be stored.

When the Caller ID list memory is full, a new call automatically replaces the oldest

call in memory. NEW appears on screen for calls received that have not been

reviewed.

Note: Check with your local phone company regarding name service

availability.

Reviewing Caller ID list

As calls are received and stored, the Caller ID list is updated to let you know how

many calls have been received.

1. Press CID/VOL

to scroll through the Caller ID list from the most recent to

the oldest.

2. Press CID/VOL

to scroll through the Caller ID list from the oldest to the

most recent.

3. Press TONE/EXIT to return to Standby Mode anytime.

Note: 1. If area code is programmed (for example 416), the whole number

(416-2225555) including area code will be shown on the screen during a call

coming from this area. When reviewed later, the area code will not be shown

(i.e. LCD shows 2225555 only). 2. You may also transfer Caller ID entries to

the directory.

See Storing caller ID entries in directory below.

Formatting Caller ID numbers

The MUTE/FORMAT key lets you select how many digits of the number are

displayed.

• Press MUTE/FORMAT once to add the area code (Note: The programmed

area code must match the Caller ID area code).

• Press MUTE/FORMAT again to add 1 plus the area code.

• Press MUTE/FORMAT a third time to go back to the 7-digit number.

CALLER ID FEATURES

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5216

Storing Caller ID entries in the directory

Before storing a caller ID number, make sure the number appears in proper digits

for your dialing area. If not, change it using the MUTE/FORMAT key. For example,

if the Caller ID number appears 1-416-222-5555 but it is not a long distance

number, press MUTE/FORMAT until it shows 416-222-5555 (without 1).

Note: If a specific memory entry is longer than 15 digits, the last 15 digits

show on the screen.

1. Use the CID/VOL

or key to select desired Caller ID entry.

2. Press MEM key, “MEMO # --” shows on the top right corner of screen.

3. Select the desired memory location by pressing the number keys (0-9).

4. If the memory location already contains name and number information,

“REPLACE MEMO?” will show on screen. Press MEM again if you want to

replace the information and save. Press *TONE/EXIT button to return unit to

standby mode without saving.

5. If the selected memory location is empty, you will hear a confirmation tone

when the new memory record is saved.

Note: If the selected CID record contains non-digit characters, or the number

is more than 24 digits, the unit will not store the record.

Dialing a Caller ID number

1. Make sure the phone is OFF (not in TALK mode).

2. Use CID

or to scroll to the desire Caller ID entry.

3. Use MUTE/FORMAT key to display the phone number in proper

digits if necessary.

4. Press TALK. The number dials automatically.

Deleting entries from the Caller list

Use CH/DEL to erase the entry currently shown on screen or all entries.

Deleting the displayed entry

1. Make sure the phone is OFF (not in TALK mode).

2. Use the CID/VOL

or keys to find the entry you want to delete.

3. While the entry is displayed, press CH/DEL. “DELETE?” shows on screen.

4. Press CH/DEL again to delete the entry. Confirmation tone sounds and LCD

shows “DELETED” for 2 seconds.

CALLER ID FEATURES

sy5822 10 april.p65 2006/5/12, ¤U¤È 02:5217

Deleting all entries

1. Make sure the phone is OFF (not in TALK mode).

2. Use the CID/VOL

or keys to display any entry.

3. Press and hold CH/DEL, until “DELETE ALL?” shows on screen.

4. Press CH/DEL again to confirm. “NO CALLS” shows on screen.

You can store up to 10 names (up to 15 characters) and numbers (up to 24 digits)

in the directory for quick dialing. If a number exceeds 24 digits, you can program

it in parts, and then chain dial the number.

Storing a number in the directory

To program a number to memory:

1. Make sure the phone is OFF (not in TALK Mode).

2. Press MEM key to start the Memory Programming Mode. “MEMO # --” shows

on the screen.

3. Select the desired memory location (0 – 9) or use the CID/VOL

keys to find an empty memory location.

4. Press the MEM key again. The screen shows “ENTER NAME”.

5. Use the digit keys to enter the name. The cursor advances 1 space after

each key press. Within 1 second, you can press the same key again to

select another character. If you make a mistake, press CH/DEL to delete

previous characters one by one.

Key Press 1 2 3 456789

– 5

press A D G J M P T W

– 6

press – BEHKNQUX

– 7

press * C F I L O R V Y

– 8

press ! ( ) $ ’ ; S ? Z

6. Press MEM again to save the name. “ENTER TEL NUMBR” shows on screen.

7. Use the digit keys to enter the desired telephone number. If you make a

mistake, press CH/DEL to delete previous digits one by one, then enter the

correct digits. If you wish to add a pause, press PAUSE two times at the

desired location. Be sure to press it twice, or you will enter a # (number sign)

Sanyo CLT-A5832 Manuale utente

Marca: Sanyo

Modello: CLT-A5832

Categoria: Telefoni

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Sanyo CLT-A5832 User manual

Documenti correlati

Sanyo CAS-A9000 Manuale utente

Sanyo CLT-A5832 Manuale utente

Questo manuale è adatto anche per

Sanyo CLT-A5832 Manuale utente

in altre lingue

Documenti correlati

Altri documenti