Sharp LL-T1803-H Manuale utente

Categoria
TV
Tipo
Manuale utente

Questo manuale è adatto anche per

LCD MONITOR
LCD FARBMONITOR
MONITEUR LCD
MONITOR LCD
MONITOR LCD
LL-T1803-H
LL-T1803-B
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE D’USO
MANUAL DE FUNCIONAMIENTO
Table of Contents / Inhaltsverzeichnis / Table des matières / Indice / Índice
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
2
3
English
Table of Contents
Notice for Users in the USA ............................................................................................................................ 4
TCO '95/ '99 ..................................................................................................................................................... 5
Notice for Users in Europe............................................................................................................................... 7
Notice for Users in the UK ............................................................................................................................... 8
Notice for Users in Australia ............................................................................................................................ 8
Tips and safety precautions ............................................................................................................................ 9
Product description .........................................................................................................................................10
Connecting the monitor and turning the monitor on and off ..............................................................................12
Connecting the monitor to a computer ........................................................................................................12
Connecting the monitor to a power source..................................................................................................12
Turning the power on ..................................................................................................................................13
Changing between input terminals ..............................................................................................................13
Turning the power off ..................................................................................................................................13
Adjusting the screen display ...........................................................................................................................14
Resetting all adjustment values .................................................................................................................14
Adjustment lock function............................................................................................................................14
Adjusting the backlight ...............................................................................................................................14
Adjusting the screen display (With analog connection) ...................................................................................15
Automatic screen adjustment.....................................................................................................................15
Manual screen adjustment .........................................................................................................................16
Adjusting the screen display (With digital connection) ....................................................................................19
Monitor care and repair ...................................................................................................................................21
Monitor care ...............................................................................................................................................21
Storage ......................................................................................................................................................21
Troubleshooting ..........................................................................................................................................21
Specifications .................................................................................................................................................22
Installing set-up information and the ICC profile (For Windows) ......................................................................25
Information about the ColorSync profile (For MacOS).....................................................................................28
Instructions for attaching a VESA compliant arm ...........................................................................................29
4
Notice for Users in the USA
FCC Statement
WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user's authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B
computing equipment.
Declaration of Conformity
SHARP LCD Color Monitor LL-T1803-H/LL-T1803-B
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undersized operation.
Responsible Party : SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
TEL :1-800-BE-SHARP
* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal
of these materials may be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities or the Electronics Industries Alliance:www.eiae.org
5
English
Congratulations!
You have just purchased a TCO’95 or TCO’99 approved and labelled product! Your choice has provided you
with a product developed for professional use. Your purchase has also contributed to reducing the burden on
the environment and also to the further development of environmentally adapted electronics products.
This product meets the requirements for the TCO’95 or TCO’99 scheme which provides for an international
environmental and quality labelling of personal computers. The labelling scheme was developed as a joint
effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation), Statens Energimyndighet (The Swedish National Energy
Administration) and SEMKO AB.
The requirements cover a wide range of issues: environment, ergonomics, usability, reduction of electric and
magnetic fields, energy consumption and electrical safety.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation
of goods and services to the environment. The main problem, as far as computers and other electronics
equipment are concerned, is that environmentally harmful substances are used both in the products and during
their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment,
most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important from
the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity
generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioac-
tive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and
thereby consumes a lot of energy.
What does the environmenal labelling involve?
The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish Society
for Nature Conservation). These demands impose restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The
product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which
must be adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of inactivity,
shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the
computer shall be reasonable for the user.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO’99 approved and labelled products may also be obtained via the Internet,
using the address: http://www.tco-info.com/
LL-T1803-B LL-T1803-H
6
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to
prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of
flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are
chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing
bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive
damage in fish-eating birds and mammals, due to the bio-accumulative * processes. Flame retardants have
been found in human blood and researchers fear that disturbances in foetus development may occur. The
relevant TCO´95 and TCO’99 demand require that plastic components weighing more than 25 grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed
circuit boards since no substitutes are available.
Cadmium **
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays.
Cadmium damages the nervous system and is toxic in high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium.
The colour-generating layers of display screens must not contain any cadmium.
The relevant TCO’99 requirement states that batteries, the colour-generating layers of display screens
and the electrical or electronics components must not contain any cadmium.
Mercury **
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is
toxic in high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of mercury. The
relevant TCO’99 requirement states that batteries may not contain any mercury.
Both TCO´95 and TCO´99 also demand that mercury is not present in any of the electrical or electronics
components associated with the labelled unit. There is however one exception. Mercury is, for the time being,
permitted in the back light system of flat panel monitors as there today is no commercially available alterna-
tive. TCO aims on removing this exception when a mercury free alternative is available.
CFCs (freons)
The relevant TCO’95 and TCO’99 requirement state that neither CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit
boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased
reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a
consequence.
Lead **
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO’95 and TCO´99 requirement permit the
inclusion of lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
7
English
Notice for Users in Europe
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by
93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung
93/68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par
la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/
EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla
direttiva 93/68/EEC.
Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ,
óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão
corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio
de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av
93/68/EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/
EEC.
CAUTION :
TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.
CAUTION :
FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.
VORSICHT :
UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN
ENTFERNEN.
ATTENTION :
POUR UN ARRET TOTAL DE L’APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.
VARNING :
FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.
PRECAUCION :
PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.
8
Notice for Users in the UK
FOR CUSTOMERS IN U.K.
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code :
GREEN-AND-YELLOW : Earth
BLUE : Neutral
BROWN : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows. The wire which is coloured GREEN-
AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the
safety earth or coloured green or green-and-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N
or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter
L or coloured red.
Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified
electrician.
"WARNING :THIS APPARATUS MUST BE EARTHED"
Notice for Users in Australia
Service Inquiries
Please contact your dealer for service if required or contact Sharp Corporation of Australia on
1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.
9
English
- Under certain display conditions, minute specks
or spots may be noticeable. This is common for
liquid crystal monitors and is not a malfunction.
- The LCD panel has been manufactured using
highly elaborate technology. Properly working
pixels comprise 99.99% of total pixels. However,
please understand that 0.01% or less of pixels
may be missing or be brighter than usual.
- Do not leave the screen displaying idly for long
periods of time, as this could cause afterimage to
remain.
- If the brightness is adjusted to the minimum
setting it may be difficult to see the screen.
- The quality of the computer signal may influence
the quality of the display. We recommend using a
computer able to emit high quality video signals.
- Never rub or tap the monitor with hard objects.
- Please understand that Sharp Corporation bears
no responsibility for errors made during use by
the customer or a third party, nor for any other
malfunctions or damage to this product arising
during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be
upgraded without advance notice.
Location
- Do not use the monitor where ventilation is poor,
where there is a lot of dust, where humidity is
high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into
contact with water or other fluids. Ensure that no
objects such as paper clips or pins enter the
monitor as this could lead to fire or electric
shock.
- Do not place the monitor on top of unstable
objects or in unsafe places. Do not allow the
monitor to come into contact with strong shocks
or vibrations. Causing the monitor to fall or topple
over may damage it.
- Do not use in places where the monitor will be
subject to direct sunlight, near heating equipment
or anywhere else where there is likelihood of high
temperature, as this may lead to generation of
excessive heat and outbreak of fire.
The Power Cord
- Do not damage the power cord nor place heavy
objects on it, stretch it or overly bend it. Also, do
not add extension cords. Damage to the cord may
result in fire or electric shock.
- Use only the AC adapter supplied with the
monitor. Using an AC adapter other than that
supplied may lead to fire.
- Insert the power plug directly into the AC outlet.
Adding an extension cord may lead to fire as a
result of overheating.
Monitor and accessory checklist
- Please check that the following items are
included in the package.
- LCD monitor (1)
- AC adapter (1)
(model name: NL-A61J)
- Analog signal cable (1)
(model name: 0LTGD15180001)
- Utility Disk (For Windows/Macintosh) (1)
- Operation manual (1)
Notes:
- The digital signal cable (DVI-D24 pin – DVI-D24
pin) is to be purchased separately. (model name:
NL-C01E)
- You are advised to retain the carton in case the
monitor needs to be transported.
- Sharp Corporation holds authorship rights to the
Utility Disk program. Do not reproduce it without
permission.
Use of AC adapter
- Do not use the AC adapter for other than the
specified equipment.
- Unplug the AC adapter if it is not used for long
time.
- Do not place any objects on the AC adapter.
- Do not use the AC adapter outdoors.
- Do not attempt to repair the AC adapter if it is
broken or malfunctioning. Refer the servicing to
the service representative.
- Do not try to open the AC adapter.
- Do not use water or wet cloth for cleaning the AC
adapter.
Manual Scope
- In this booklet, Microsoft Windows XP will be
referred to as [WindowsXP], Microsoft Windows
Millenium as [WindowsMe], Microsoft Windows
2000 as [Windows2000], Microsoft Windows 98
as [Windows98], Microsoft Windows 95 as
[Windows95], and Microsoft Windows Version 3.1
as [Windows3.1]. When there is no need to
distinguish between programs, the term
[Windows] will be used.
- Microsoft and Windows are registered
trademarks of Microsoft Corporation.
- Macintosh is a registered trademark of Apple
Computer, Inc.
Tips and safety precautions
10
Product description
654
32
1
78
11
11
11
10
9
1. INPUT button ............................ To switch between the signals input terminals. (Analog signal input
terminal
DVI-D input terminal)
2. MENU button ............................ This button is used to pop-up, select and close the OSD (On Screen
Display) Menu.
3. SELECT button ........................ This button is used to select menu options when the OSD Menu is dis-
played.
4.
buttons .............................. When the OSD Menu is displayed:
These buttons are used to increase or decrease the value of a selected
option.
When the OSD Menu is not displayed:
These buttons are used to adjust backlight brightness .
5. Power LED ................................ This LED is lit green when in use and orange when in power-saving mode.
6. Power button
7. Power terminal
8. Analog signal input terminal ...... Use this when connecting to the computers analog RGB output terminal.
9. DVI-D input terminal .................. Use this when connecting to the computers digital RGB output terminal.
It can be connected to a computer with a DVI-compatible output terminal
(DVI-D24 pin or DVI-I29 pin) and which has SXGA output ability.
(Depending on the computer to be connected, correct display may or may
not be possible.)
In order to connect, it is necessary to purchase a Digital signal
cable.(Model name: NL-C01E)
10.Security lock anchor ................. By connecting a security lock (purchased separately) to the security lock
anchor, the monitor is fixed so that it cannot be transported.
The security slot works in conjunction with Kensington Micro Saver
Security Systems.
11.Ventilation openings .................. Note: Never block the ventilation openings as this may lead to overheat-
ing inside the monitor and result in malfunction.
11
English
Standing up and adjusting the monitor
CAUTION!
- Pressure from hands on the LCD panel could
cause damage.
- Be careful not to allow your fingers to be pinched.
Standing up the monitor
Press down on the stand and lift up the top section
of the monitor.
Folding up the monitor
1. Remove the AC adapter and the RGB signal
cable.
2. If carrying out adjustments to the monitor, place it
upright.
3. While pressing the rear lock disable button (1),
gently fold back the monitor (2).
(2)
(1)
Angle adjustment
Adjust to an easy to view angle.
45
45
15
Product description
12
CAUTION!
- When connecting, ensure that both the monitor
and computer are switched off.
- Be careful not to overly bend the cable or add
extension cords as this could lead to a
malfunction.
Connecting the monitor to a computer
Analog RGB connection
Connect this devices analog signal cable to the
computer.
- Paying attention to connector direction, firmly
insert the signal cable to terminal, and then
tighten the screws at both sides.
If connecting to a D-sub 15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter
(to be purchased separately) to the analog signal
cable.
Connecting the monitor and turning
the monitor on and off
Analog RGB terminal
(Mini D-Sub 15 pin, 3 row)
Analog signal cable
Macintosh conversion adapter
Digital RGB connection
Connecting the monitor to a computer via a Digital
signal cable. (to be purchased separately)
- For digital RGB connection, the monitor has an
input for connecting to a computer with a DVI-
compatible output connector (DVI-D 24 pin or DVI-
I 29 pin) and SXGA output capability. (Depending
on the type of computer to be connected, the
display may not work correctly.)
- Paying attention to connector direction, firmly
insert the signal cable to terminal, and then
tighten the screws at both sides.
Connecting the monitor to a power source
1. Connect the AC adapter to the monitor's power
terminal
2. Attach the power cord to the AC adapter and
place the power plug into the AC outlet.
Digital signal cable
Digital RGB output
terminal (DVI-D 24
pin or DVI-I 29 pin)
DVI-D input terminal
(DVI-D24 pin)
AC adapter
Power terminal
Power cord
AC outlet
13
English
Connecting the monitor and turning the monitor on and off
CAUTION!
- After unplugging the AC adaptor or power cord, be
sure to wait at least 10 seconds before plugging
in again. If you put the plug back in immediately
after unplugging, damage may be caused and the
screen malfunction or not display.
Turning the power on
1. Press the monitor's POWER button.
2. Turn on the computer.
The power LED will be lit green, and the screen
will display an image.
ON
Notes: (when using an analog signal)
- If using the monitor for the first time or after
having changed the system settings during use,
perform an automatic screen adjustment (p. 15).
- When connecting to a notebook, if the notebook
computer's screen is set so that it is displaying at
the same time, the MS-DOS screen may not be
able to display properly. In this case, change the
settings so that only the monitor is displaying.
Changing between input terminals
Use the INPUT button to switch between signal input
terminals.
Analog RGB signal Digital RGB signal
INPUT
INPUT
INPUT-2(DIGITAL)
INPUT-1(ANALOG)
Turn on the
computer
Press power button
Turning the power off
1. Turn the computer off.
2. Press the monitor's POWER button.
The Power LED will disappear.
OFF
If the monitor is not going to be used for a long
period of time, be sure to unplug it from the AC
outlet.
Press power button
Turn the
computer off
14
Adjusting the screen display
For analog signal
1. First perform an automatic adjustment. (p. 15)
2. Perform manual adjustment where necessary.
(p. 16)
For digital signal
The monitor can generally be used without
adjustment. If necessary perform manual
adjustment. (p. 19)
Note:
- All adjustments will be saved even after turning
the power off.
Resetting all adjustment values
All adjustment values can be returned to their origi-
nal ex-factory values in one command.
1. Turn off the monitor power.
2. Press the MENU button and the SELECT button
simultaneously, and while doing this press the
power button (i.e. turn the power on). When [ALL
RESET] appears on the screen, the reset is
complete.
Note:
- While ALL RESET is displayed, the control
buttons are disabled.
- It is not possible to reset values when the
adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.
Adjustment lock function
By disabling the control buttons (i.e. setting the lock)
any attempted changes to adjusted values will be
voided.
1. Turn off the monitor power.
2. While pressing the MENU button, press the
power button (i.e. turn the power on).
Continue to press the button until the message
appears on the screen.
When the menu is unlocked:
[ADJUSTMENT LOCKED] will appear on
the screen, and the lock will be set.
When the menu is locked:
[ADJUSTMENT UNLOCKED] will appear
on the screen, and the lock will be
removed.
Note:
- When the lock is in place, all buttons other than
the power button are disabled.
Adjusting the backlight
The backlight brightness can be adjusted.
Carry out the commands without the On Screen
Display (OSD) Menu displayed. If the OSD Menu is
displayed, press the MENU button (several times
may be required) and begin when the OSD Menu has
disappeared.
1. Without the OSD Menu being displayed, push the
or the button. At the bottom of the screen
the BRIGHT bar will appear.
2. Adjust by pressing the button (darker) or
button (lighter).
The BRIGHT bar automatically disappears several
seconds after the last command.
15
English
Adjusting the screen display (With analog connection)
Automatic screen adjustment
Options in the ADJUSTMENT Menu can be adjusted
automatically (CLOCK, PHASE, H-POS V-POS).
Note:
- When setting up this monitor for the first time or
after having changed an aspect of the current
system, perform an automatic screen adjustment
before use.
On Screen Display for the automatic
adjustment
First display an image that makes the entire screen
light.
If you are using Windows, you can use Adjustment
Pattern on the accompanying Utility Disk.
Opening the Adjustment Pattern (for Windows)
This explanation is for Windows 95/98/2000/Me/XP,
and assumes that the floppy disk drive is "A drive".
1. Place the Utility Disk (provided) into the
computers A drive.
2. Open [My Computer] and select [3 ½ Floppy
[A:]]. If using Windows 3.1, open [File Manager]
and choose A drive.
3. Double click on [Adj_uty.exe] to run the
Adjustment Program. The Adjustment Pattern will
appear.
Adjustment pattern
Notes:
- After completing the adjustments, press the
computers [Esc] key to exit the Adjustment
Program.
- If your computers display mode is set to 65K
colors, you may see the different color levels in
each color pattern or the gray scale may look
colored. (This is due to the specification of the
input signal and is not a malfunction.)
How to Adjust
1. Press the MENU button.
The ADJUSTMENT Menu will be displayed.
2. Press the button.
The screen will become dark and [ADJUSTING]
will be displayed. After a few seconds the
ADJUSTMENT Menu will return. (The automatic
adjustment is now complete.)
3. Press the MENU button 4 times to make the
OSD Menu disappear.
Notes:
- In most cases automatic adjustment is sufficient.
- If necessary due to any of the following, manual
adjustments (p. 16) can be performed after the
automatic adjustment.
- When further fine adjustment is needed.
- When the computers video input signals are
Composite Sync or Sync On Green.
(Automatic adjustments may not be possible.)
- When [OUT OF ADJUST] is displayed.
(When the screen displays an entirely dark
image, the automatic screen adjustment may
be disabled. When making an automatic
adjustment, be sure to either use the
Adjustment Pattern or try displaying an image
that makes the entire screen very bright.)
16
Manual screen adjustment
Adjustments can be made using On Screen Display
(OSD) Menu provided.
On Screen Display for adjustment
If you are using Windows, open the Adjustment
Pattern on the accompanying Utility Disk. (p. 15).
If your system is not Windows, you can not use the
Adjustment Pattern. Therefore display an image that
makes the entire screen light and adjust it through
checking visually its actual tone.
This chapter provides the procedure how to adjust
the screen by using Adjustment Pattern (for Win-
dows)
How to adjust
1. Press the MENU button.
The ADJUSTMENT Menu will be displayed.
At this point relevant menu options can be
adjusted.
Each time the MENU button is pressed the next
menu is selected. (ADJUSTMENT GAIN
CONTROL WHITE BALANCE MODE
SELECT OSD Menu disappears)
Notes:
- The OSD Menu automatically disappears several
seconds after the last command.
ADJUSTMENT Menu
MANUAL: Individual menu options are manually
adjusted.
AUTO: Every menu option is automatically
adjusted.
Notes:
- Press the
button to select [AUTO].
- To choose a menu option:SELECT button
- To go to the next menu: MENU button
CLOCK
The figure below demonstrates how to adjust so that
vertical flicker noise is not emitted. (
buttons)
PHASE
The figure below demonstrates how to adjust so that
horizontal flicker noise is not emitted. (
buttons)
Note:
- Adjustments to PHASE should be made only
after CLOCK has been correctly set.
H-POS (horizontal positioning) and V-POS
(vertical positioning)
To center the screen image within the boundaries of
the screen, adjust the left-right (H-POS) values and
the up-down (V-POS) values. (
buttons)
Adjusting the screen display (With analog connection)
Vertical flicker noise
Horizontal flicker noise
Screen frame
17
English
WHITE BALANCE Menu
Notes:
- On settings other than [STD] not all graduations
can be displayed. To display all graduations, set
to [STD].
- Use the
buttons to select [COOL], [·], [STD],
[·], [WARM] or [USER].
- Selecting USER will display the setting values for
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST], in order to make fine
adjustments.
- Use the SELECT button to select
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].
- To go to the next menu: MENU button
COOL ... Color tone bluer than standard
......... Color tone slightly bluer than standard
STD ...... Color tone standard setting
......... Color tone slightly redder than standard
WARM .. Color tone redder than standard
USER
R-CONTRAST ....
button for blue-green
button for red
G-CONTRAST ....
button for purple
button for green
B-CONTRAST ....
button for yellow
button for blue
GAIN CONTROL Menu
MANUAL: Individual menu options are manually
adjusted.
AUTO: Every menu option is automatically
adjusted using the Auto Gain Control*
function.
Notes:
- Press the
button to select [AUTO].
- To choose a menu option:SELECT button
- To go to the next menu: MENU button
* Auto Gain Control function
- The Auto Gain Control adjusts contrast and black
level based on the brightest color of the image
displayed. If you are not using the Adjustment
Pattern it is necessary to have an area of 5 mm x
5 mm of white displayed, and if not adjustments
may not be possible. (In such case, [OUT OF
ADJUST] will appear and setting values remain
unchanged.)
- If the signal coming from the computer is
composite sync or sync on green, automatic
adjustment cannot be performed. Please perform
manual adjustment instead.
BLACK LEVEL
Total screen brightness can be adjusted while
watching the color pattern. (
buttons)
CONTRAST
While watching the color pattern, adjustments can be
made so that all graduations appear. (
buttons)
Adjusting the screen display (With analog connection)
Color pattern
18
MODE SELECT Menu
Notes:
- Depending on the resolution of the input signal,
even if menu options can be selected, the display
may not change.
- To choose a menu option: SELECT button
- When adjustment complete: MENU button
OSD H-POSITION (OSD horizontal position)
The position of the OSD display can be moved to the
left and right. (
buttons)
OSD V-POSITION (OSD vertical position)
The position of the OSD display can be moved up
and down. (
buttons)
INPUT (Input mode)
The input mode can be set. (
buttons)
VESA: VESA mode
MAC: Power Macintosh mode
400 LINES (degree of resolution)
You can specify the horizontal resolution of a 400-
line screen when using US text, etc. (
buttons)
640: 640 X 400 dot mode
720: 720 X 400 dot mode (US text etc.)
Note:
- As the resolution input for other than 400 lines is
done automatically, there is no need to set it.
SCALING (Level of scaling)
Adjusts the image to optimum sharpness when
Screen expansion is taken. (
buttons)
LANGUAGE
You can chose the language used in OSD Menu.
1. Press the
button.
Language Selection Menu (LANGUAGE) will
appear.
2. Chose the desired language by SELECT button.
3. Press MENU button or the
button, and
Language Selection Menu will disappear.
Adjusting the screen display (With analog connection)
19
English
Adjusting the screen display (With digital connection)
Adjustments can be made using On Screen Display
(OSD) Menu provided.
On Screen Display for adjustment
If you are using Windows, open the Test Pattern on
the accompanying Utility Disk. (p. 15)
If your system is not Windows, you can not use the
Adjustment Pattern. Therefore display an image that
makes the entire screen light and adjust it through
checking visually its actual tone.
How to adjust
1. Press the MENU button.
The WHITE BALANCE Menu will be displayed.
At this point relevant menu options can be
adjusted.
Each time the MENU button is pressed the next
menu is selected. (WHITE BALANCE MODE
SELECT OSD Menu disappears)
Notes:
- The OSD Menu automatically disappears several
seconds after the last command.
WHITE BALANCE Menu
Notes:
- On settings other than [STD] not all graduations
can be displayed. To display all graduations, set
to [STD].
- Use the
buttons to select [COOL], [·], [STD],
[·], [WARM] or [USER].
- Selecting USER will display the setting values for
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST], in order to make fine
adjustments.
- Use the SELECT button to select
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].
- To go to the next menu: MENU button
COOL ... Color tone bluer than standard
......... Color tone slightly bluer than standard
STD ...... Color tone standard setting
......... Color tone slightly redder than standard
WARM .. Color tone redder than standard
USER
R-CONTRAST ....
button for blue-green
button for red
G-CONTRAST ....
button for purple
button for green
B-CONTRAST ....
button for yellow
button for blue
20
Adjusting the screen display (With digital connection)
MODE SELECT Menu
Notes:
- Depending on the resolution of the input signal,
even if menu options can be selected, the display
may not change.
- To choose a menu option: SELECT button
- When adjustment complete: MENU button
OSD H-POSITION (OSD horizontal position)
The position of the OSD display can be moved to the
left and right. (
buttons)
OSD V-POSITION (OSD vertical position)
The position of the OSD display can be moved up
and down. (
buttons)
SCALING (Level of scaling)
Adjusts the image to optimum sharpness when
Screen expansion is taken. (
buttons)
LANGUAGE
You can chose the language used in OSD Menu.
1. Press the
button.
Language Selection Menu (LANGUAGE) will
appear.
2. Chose the desired language by SELECT button.
3. Press MENU button or the
button, and
Language Selection Menu will disappear.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144

Sharp LL-T1803-H Manuale utente

Categoria
TV
Tipo
Manuale utente
Questo manuale è adatto anche per