ABB PowerValue 11 RT G2 Istruzioni per l'uso

—

QUICK GUIDE

PowerValue 11 RT G2

6-10 kVA

2 P OW ER VA L U E 11 R T G 2 6 -1 0 K VA Q UI C K GU I D E

ocument information

4NWP103183R0001_ABB_QIG_PVA11 6-10kVA-RT_ML_REV-B

PowerValue 11 RT G2 6-10 kVA

06.04.201

8

Product Marketin g

R&D

After Sale s

4NWP103183R000 1

4NWD003879

B

Article number :

Document number :

Revision :

PLEASE FULLY READ THIS QUICK GUIDE BEFORE READING THE USER MANUAL AND

OPERATING ON THE UNIT.

File name

UPS model

Date of issue

Issued by

Checked by

:

—

D

DOCUMENT INFORMATION 3

—

01

—

02

4

—

03

—

04

DOCUMENT INFORMATION 5

10 11 12

2 4 5 6 7 8 91 3

14 1115

13

—

05

—

06

—

07

6

CONTENTS 7

—

QUICK GUIDE

PowerValue 11 RT G2

6-10 kVA

DEUTSCH

PORTUGUÊS

Р У́ С С К И Й

FRANÇAIS

SUOMI

POLSKI

DANSK

ΕΛΛΗΝΙΚΆ

ITALIANO

SVENSKA

中文

ČEŠTINA

DUTCH

ENGLISH

ESPAÑOL

Quick guide 9

Kurzanleitung 23

Guide de référence rapide 39

Guida rapida 55

Guía rápida 71

Guia de Consulta Rápida 87

Pikaopas 103

Kort handledning 119

Kvikguide 133

Rychlý průvodce 147

Краткое руководство 161

Skrócony podręcznik 177

速成指南 193

Σύντομος οδηγός 207

Beknopte installatiehandleiding 223

8

—

QUICK GUIDE

PowerValue 11 RT G2

6-10 kVA

Important safety instructions 10

Installation 15

Operation 17

Troubleshooting 19

ENGLISH

10 POWERVALUE 11 RT G2 6-10 KVA QUICK GUIDE

—

Important safety instructions

READ THIS IMPORTANT SAFETY INSTRUCTION CHAPTER BEFORE

READING THE OPERATING MANUAL

Always follow the precautions and

instructions described in this

manual. Any deviations from the

instructions may result in electrical

shock or cause accidental load loss.

ABB DOES NOT TAKE ANY

RESPONSIBILITY FOR DAMAGES

CAUSED THROUGH INCORRECT

MANIPULATIONS OF THE UPS

SYSTEM.

The following symbols are used in this manual, the list below explains

each symbol.

THIS SYMBOL IN CONJUNCTION WITH THE SIGNAL WORD “DANGER”

INDICATES AN IMMINENT ELECTRICAL HAZARD. FAILURE TO OBSERVE THE

RELATED SAFETY NOTE MAY CAUSE INJURY, DEATH OR EQUIPMENT

DAMAGE.

THIS SYMBOL IN CONJUNCTION WITH THE SIGNAL WORD “WARNING”

INDICATES A POTENTIALLY DANGEROUS SITUATION. FAILURE TO OBSERVE MAY

CAUSE INJURY, DEATH OR EQUIPMENT DAMAGE.

THIS SYMBOL IN CONJUNCTION WITH THE SIGNAL WORD “NOTE”

INDICATES OPERATOR TIPS OR PARTICULARLY USEFUL OR IMPORTANT

INFORMATION FOR THE USE OF THE PRODUCT. THIS SYMBOL AND

WORDING DOES NOT INDICATE A DANGEROUS SITUATION.

THIS SYMBOL INDICATES THAT READING THE INSTRUCTION MANUAL/

BOOKLET BEFORE STARTING WORK OR BEFORE OPERATING EQUIPMENT OR

MACHINERY IS COMPULSORY.

—

Operator precautions

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS 11

BATTERIES

DANGER

COMPONENTS INSIDE THE UPS ARE CONNECTED TO THE BATTERY EVEN

WHEN THE UPS IS DISCONNECTED FROM THE MAINS POWER SUPPLY.

DANGER

DISCONNECT THE BATTERIES BEFORE CARRYING OUT ANY KIND OF SERVICE

AND/OR MAINTENANCE. VERIFY THAT NO CURRENT IS PRESENT AND NO

HAZARDOUS VOLTAGE EXISTS IN THE CAPACITOR OR BUS CAPACITOR

TERMINALS.

DANGER

A BATTERY CAN PRESENT A RISK OF ELECTRICAL SHOCK AND HIGH SHORT

CIRCUIT CURRENT. THE FOLLOWING PRECAUTIONS MUST BE OBSERVED

WHEN WORKING ON BATTERIES:

• REMOVE WATCHES, RINGS OR OTHER METAL OBJECTS

• MAKE USE OF PROPER PPE (PERSONAL PROTECTION EQUIPMENT) AS PER

LOCAL POLICIES AND RULES

- WEAR FLAME/ARC RESISTANT WHOLE BODY CLOTHING

- WEAR SUITABLE VOLTAGE RATED GLOVES

- USE SAFETY DIELECTRIC FOOTWEAR

- WEAR ARC FLASH FACE SHIELD

- USE VOLTAGE RATED TOOLS

• DO NOT LAY TOOLS OR METAL PARTS ON TOP OF BATTERIES

• DISCONNECT THE CHARGING SOURCE PRIOR TO CONNECTING OR

DISCONNECTING BATTERY TERMINALS.

DANGER

THE BATTERY CIRCUIT IS NOT ISOLATED FROM THE INPUT VOLTAGE.

HAZARDOUS VOLTAGES MAY OCCUR BETWEEN THE BATTERY TERMINALS

AND THE GROUND. VERIFY THAT NO VOLTAGE IS PRESENT BEFORE

SERVICING.

WARNING

NEVER DISPOSE BATTERIES ON FIRE AS THEY MAY EXPLODE.

WARNING

DO NOT OPEN OR DAMAGE THE BATTERIES.

ENGLISH

12 POWERVALUE 11 RT G2 6-10 KVA QUICK GUIDE

WARNING

RELEASED ELECTROLYTE IS HARMFUL TO THE SKIN AND EYES.

WARNING

REPLACE BATTERIES WITH THE SAME NUMBER AND SAME TYPE OF

BATTERIES.

INSTALLATION

DANGER

DISPLAY A WARNING LABEL ON ALL PRIMARY POWER ISOLATORS INSTALLED

REMOTE FROM THE UPS AREA TO WARN ELECTRICAL MAINTENANCE

PERSONNELS THAT THE CIRCUIT FEEDS A UPS.

MAKE SURE THAT WARNING LABEL CONTAINS THE FOLLOWING TEXT OR

EQUIVALENT: “ISOLATE THE UPS (UNINTERRUPTIBLE POWER SUPPLY)

BEFORE WORKING ON THIS CIRCUIT”.

DANGER

HIGH FAULT CURRENTS (LEAKAGE CURRENTS). BEFORE CONNECTING THE

MAINS ENSURE THAT THE UPS IS GROUNDED!

DANGER

DO NOT REMOVE ANY SCREWS FROM THE UPS SYSTEM OR FROM THE

BATTERY CABINET: DANGER OF ELECTRICAL SHOCK.

DANGER

WHEN OPENING OR REMOVING THE UPS-COVERS YOU ARE EXPOSED TO

DANGEROUS VOLTAGES.

DANGER

RISK OF BACKFEED VOLTAGE, ISOLATE THE UPS INSTALLING AN EXTERNAL

ISOLATING DEVICE BETWEEN MAINS INPUT AND UPS; BEFORE OPERATING

ON THIS CIRCUIT, CHECK FOR HAZARDOUS VOLTAGE.

DANGER

TO REDUCE THE RISK OF FIRE, THE UNIT SHOULD ONLY CONNECT TO A

CIRCUIT PROVIDED WITH BRANCH CIRCUIT OVERCURRENT PROTECTION FOR:

• D CURVE 63A RATING (UPSTREAM CIRCUIT), FOR 6KVA MODELS,

• D CURVE 80A RATING (UPSTREAM CIRCUIT), FOR 10KVA MODELS.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS 13

DANGER

HIGH LEAKAGE CURRENT:

MAKE SURE THAT THE EARTH WIRE IS CONNECTED.

COMMON INPUT/OUTPUT SOURCES CONNECTION

WARNING

BEFORE CARRING OUT ANY CONNECTION, CHECK THAT THE UPSTREAM

PROTECTION DEVICES (NORMAL AC SOURCE AND BYPASS AC SOURCES) ARE

OPEN “0” (OFF).

WARNING

WATER CONDENSING MAY OCCUR IF THE UPS IS UNPACKED IN A VERY LOW

TEMPERATURE. IN THIS CASE IT IS NECESSARY TO WAIT UNTIL THE UPS IS

FULLY DRIED INSIDE OUT BEFORE PROCEEDING INSTALLATION AND USE TO

AVOID HAZARDS AND ELECTRIC SHOCK, WAIT UNTIL THE UPS IS FULLY DRY

BOTH INSIDE AND OUTSIDE BEFORE INSTALLING.

WARNING

INDUCTIVE LOADS (FOR EXAMPLE MONITORS AND LASER PRINTERS) HAVE A

VERY HIGH POWER CONSUMPTION AT START-UP. IF CONNECTED TO THE

UPS, THE START-UP POWER OF SUCH LOADS MUST BE TAKEN INTO

CONSIDERATION WHEN CALCULATING THE CAPACITY OF THE UPS TO

PREVENT THE UPS FROM BEING OVERLOADED AND TURNED OFF.

NOTE

TO REDUCE THE RISK OF FIRE, CONNECT THE UPS TO A CIRCUIT PROVIDED

WITH BRANCH CIRCUIT OVERCURRENT PROTECTION WITH AN AMPERE

RATING IN ACCORDANCE WITH THE IEC/EN 60934 STANDARD OR YOUR

LOCAL ELECTRICAL CODE.

SEE TECHNICAL SPECIFICATIONS FOR RECOMMENDATIONS.

OPERATION

WARNING

DO NOT OPERATE IN CASE OF PRESENCE OF WATER OR MOISTURE.

WARNING

DO NOT DISCONNECT THE MAINS CABLE FROM THE UPS OR THE BUILDING

WIRING SOCKET DURING OPERATION AS THIS REMOVES THE GROUND FROM

THE UPS AND ALL CONNECTED LOADS.

WARNING

SWITCH OFF THE CONNECTED LOADS BEFORE TURNING ON THE UPS. THEN

SWITCH ON THE LOADS ONE BY ONE AFTER THE UPS IS TURNED ON. SWITCH

OFF ALL OF THE CONNECTED LOADS BEFORE TURNING OFF THE UPS.

ENGLISH

14 POWERVALUE 11 RT G2 6-10 KVA QUICK GUIDE

WARNING

REPLACE FUSES ONLY BY DEVICES OF THE SAME TYPE AND OF THE SAME

AMPERAGE TO AVOID FIRE HAZARDS.

NOTE

PRESS THE OFF BUTTON TO FULLY DISCONNECT THE UPS. WAIT UNTIL THE

UPS IS ON BYPASS OR ON STAND-BY MODE BEFORE DISCONNECTING IT

FROM THE MAINS.

NOTE

INDISCRIMINATE OPERATION OF SWITCHES MAY CAUSE OUTPUT LOSS OR

DAMAGE TO EQUIPMENT.

ENGLISH

INSTALLATION 15

—

Installation

Planning before the installation

To ensure a long service life, install

the unit in a position where any

danger to the UPS is minimized:

• Install the UPS indoors.

• Leave 50 cm of space on each side

of the cabinet to allow cooling

airflow and ensure that the

circulation of air to the ventilation

slits is not obstructed.

• Avoid excessively high

temperatures and excessive

moisture.

• Make sure that the surface is solid

and flat.

Rack mount installation – requires

rack mounting kit, to be purchased

separately

This procedure is suitable for

19-inch rack cabinet installation

with a minimum depth of 800 mm.

Identify the final position and keep

2U spacing for this installation.

Note that you already installed a rail

kit to the rack cabinet for this

operation, and 1U is recommended

for this job:

1. Install the ear bracket onto the

unit using the M4 flathead

screws (figure 1).

2. Slide the unit into the rail kit and

make sure to tighten the rack-

mounting screw (figure 2).

3. If installing additional UPS units,

repeat the steps above for each

cabinet

Tower installation

UPS:

To install the UPS in a vertical

(tower) position:

1. Rotate the LCD model to tower

direction. (figure 3).

2. Set up the stabilizer bracket then

put the unit into the stabilizer

bracket. (figure 4)

External battery modules:

To install the external battery

module in a vertical (tower)

position:

1. Set up the extension plate as

below and install it on the UPS

stabilizer bracket. (figure5)

2. Install the UPS and EBM

individually into the stabilizer

bracket. (figure 5)

3. Connect to the UPS with the

battery power cable (refer to rack

position installation).

Note: It is recommended that this

unit be installed to UPS’s righthand

side. If installing an additional unit,

ENGLISH

16 POWERVALUE 11 RT G2 6-10 KVA QUICK GUIDE

place it next to the previous unit.

Electrical connections

• PowerValue 11 RT G2 6-10 kVA

(see figure 6)

Legend:

1 Dry IN/OUT

2 SNMP/ AS400 slot

3 RJ11 (PDU connection)

4 Parallel card

5 Output breaker

6 Output socket

7 Input/Output terminals

8 Input breaker

9 EBM connector

10 USB

11 RS232

12 EPO

• External battery module

(see figure 7)

Legend:

13 EBM terminal

14

Fuse board cover (to replace

EBM fuse)

15 EBM connector

ENGLISH

OPERATION 17

—

Operation

You can operate the UPS through

the user-friendly display

(see chapter 4 of the user manual

for a full list of possible operations).

ESC

Battery Load

20

Min

100

%

Output

230 50

V

Hz

Selection keys

LED’s

Battery mode Bypass mode

FaultOnline mode

Escape Up Down Enter On/Off

LCD display

UPS start-up

To start up the UPS with mains

supply:

1. Check that all cables are securely

and correctly connected.

2. Keep the power button pressed

for longer than 1 s. The fans will

activate and the UPS will load for

a few seconds.

3. The UPS will perform a self-test

and the LCD will show the default

UPS status screen.

To start up the UPS without mains

supply (cold start):

1. Check that all cables are securely

and correctly connected.

2. Keep the power button pressed

for longer than 1 s. The UPS will

power on, the fans will activate

and the LCD will turn on. The UPS

will perform a self-test and show

the default UPS status screen.

3. Keep the power button pressed

for longer than 1 s. The alarm

buzzer will sound for 1 s and the

UPS will start up.

ENGLISH

18 POWERVALUE 11 RT G2 6-10 KVA QUICK GUIDE

4. After a few seconds, the UPS

transfers to battery mode. When

the UPS is supplied with power

from the mains, the UPS

transfers to online mode without

interrupting the UPS power

output.

UPS Shutdown

To shut down the UPS with mains

supply:

1. If the UPS is working in bypass

mode, go to step 3.

2. If the UPS is in online mode, keep

the power button pressed for

more than 3 seconds. The alarm

buzzer will sound and the UPS

will transfer to bypass mode.

3. Disconnect the mains power

supply. The display will shut

down and the output voltage will

be removed from the UPS output

terminal.

4. If the bypass has been disabled

via the Settings menu, keep the

power button pressed for longer

than 3 seconds to shut down the

UPS. The unit will transfer from

online to standby mode.

Disconnect the input power

cable and the display will shut

down.

To shut down the UPS without

mains supply:

1. To power off the UPS, keep the

power on/off button pressed for

more than 3 seconds. The alarm

buzzer will sound for 3 s and the

output power will be immediately

cut off.

2. The display will shut down and

the output voltage will be

removed from the UPS output

terminal.

ENGLISH

TROUBLESHOOTING 19

—

Troubleshooting

Alarm and events indicate warnings

and notify of errors or potential

failures in the system. The output of

the UPS is not necessarily affected

in case of an alarm but taking the

correct actions may prevent loss of

power to the load. If the UPS system

does not operate correctly, attempt

to solve the problem using the

table below.

Alarm or Event Possible cause Remedy

Battery mode

Battery (Orange) LED is on.

1 beep every 4 seconds.

Code: E062

A utility failure has occurred

and the UPS is in battery

mode.

The UPS is powering the

equipment with battery

power. Prepare your

equipment for shutdown.

Battery low

Battery(Orange) LED is On.

1 beep every 1 second.

Code: A012

The UPS is in battery mode

and the battery is running

low.

This warning is approximate,

and the actual time to

shutdown may vary

significantly.

Depending on the UPS load

and number of extended

battery modules (EBMs), the

“Battery Low” warning may

occur before the batteries

reach 20 percent capacity.

No battery

Fault (Red) LED is Flash

1beep every 1 second

Code: A011

The batteries are

disconnected.

Verify that all batteries are

properly connected. If the

condition persists, contact

your service representative.

Bypass mode

Bypass (Orange) LED is on.

Code: E060

An overload or a fault has

occurred, or a command has

been received and the UPS is

in bypass mode.

Equipment is powered but

not protected by the UPS.

Check for one of the

following alarms: over

temperature, overload or UPS

failure.

Power overload

Fault (Red) LED is Flash

2beep every 1 second

Code: A041

Power requirements exceed

the UPS capacity.

Remove some of the

equipment from the UPS. The

UPS continues to operate,

but may switch to bypass

mode or shut down if the

load increases.

The alarm resets when the

condition becomes inactive.

ENGLISH

20 POWERVALUE 11 RT G2 6-10 KVA QUICK GUIDE

Alarm or Event Possible cause Remedy

UPS over temperature

Fault (Red) LED is On.

Beep continuous.

Code: F081

The UPS internal heat sink

temperature is too high, or a

fan has failed. At the warning

level, the UPS generates the

alarm but remains in the

current operating state. If

the temperature rises

another 2°C, the UPS

transfers to bypass mode or

standby mode.

Clear vents and remove any

heat sources. Allow the UPS

to cool. Ensure the airflow

around the UPS is not

restricted.

Restart the UPS. If the

condition persists, contact

your service representative.

ON Maintenance Bypass

Bypass (Orange) LED is on.

Code: A072

UPS was manually

commanded to switch to

bypass and will remain in

bypass until commanded out

of bypass.

Check the maintenance

bypass switch status.

In HE Mode

Line(green) LED is on.

Code: E063

The UPS is on bypass while

operating on the high

efficiency setting.

The equipment transferred

to bypass utility power as a

normal function of high

efficiency operation. Battery

mode is available and your

equipment is protected.

Site Wiring Fault

Fault (Red) LED is flash

1beep every 1 second

Code: A004

Site fault detection is

supported on all models any

time there is a grounding

neutral connection. Alarm

triggers when the difference

between ground and neutral

voltage is >15 V.

Site fault detection should be

enabled by default. It can still

be enabled / disabled from

the LCD settings menu.

Reconnect all input wires.

Back feed

Fault (Red) LED is On.

Beep continuous.

Code: F093

UPS has an unexpected

bypass current on battery

mode.

Transfer to maintenance

bypass and call service.

Inv Overload Fault

Fault (Red) LED is On

Beep continuous.

Code: F042

UPS has transferred to

bypass or fault mode

because of overload in

inverter mode.

The UPS transfers to battery

mode if supporting the load.

Remove some of the

equipment from the UPS.

Byp Overload Fault

Fault (Red) LED is On.

Beep continuous.

Code: F043

UPS has cut off the output

and transferred to fault

mode because of overload in

bypass mode or HE mode.

Remove some of the

equipment from the UPS.

Output Short Circuit

Fault (Red) LED is On.

Beep continuous.

Code: F031

Indicates that the UPS has

detected abnormally low

impedance placed on its

output and considers it a

short circuit.

Remove all the loads. Turn off

the UPS. Check if UPS output

and load has short circuit.

Ensure short circuit is

removed before turning on

again.

Fan Failure

Fault (Red) LED is flash

1 beep every 1 second

Code: A085

Indicates that the fan could

not work normally.

Check fans of UPS.

ENGLISH

La pagina sta caricando ...

ABB PowerValue 11 RT G2 Istruzioni per l'uso

Questo manuale è adatto anche per

ABB PowerValue 11 RT G2 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti