Asus RS520A-E12-RS24U Manuale utente

2U Rackmount Server

User Guide

RS520A-E12 Series

RS520A-E12-RS24U

ii

No part of this manual, including the products and software described in it, may be reproduced, transmitted,

transcribed, stored in a retrieval system, or translated into any language in any form or by any means,

except documentation kept by the purchaser for backup purposes, without the express written permission

of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not

limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no

event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental,

or consequential damages (including damages for loss of profits, loss of business, loss of use or data,

interruption of business and the like), even if ASUS has been advised of the possibility of such damages

arising from any defect or error in this manual or product.

Specifications and information contained in this manual are furnished for informational use only, and are

subject to change at any time without notice, and should not be construed as a commitment by ASUS.

ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,

including the products and software described in it.

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless

such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identification or explanation and to the

owners’ benefit, without intent to infringe.

E22232

Revised Edition V5

June 2023

iii

Contents

Safety information ..................................................................................................... vii

About this guide ......................................................................................................... xi

Chapter 1: Product Introduction

1.1 System package contents ......................................................................... 1-2

1.2 Serial number label .................................................................................... 1-3

1.3 System specifications ...............................................................................1-4

1.4 Front panel features ...................................................................................1-7

1.5 Rear panel features ....................................................................................1-8

1.6 Internal features .........................................................................................1-9

1.7 LED information .......................................................................................1-10

1.7.1 Front panel LEDs ...................................................................... 1-10

1.7.2 Storage device status LED........................................................ 1-11

1.7.3 LAN (RJ-45) LEDs .................................................................... 1-11

1.7.4 Rear panel LEDs ....................................................................... 1-12

1.7.5 Q-Code table ............................................................................. 1-13

Chapter 2: Hardware Information

2.1 Chassis cover .............................................................................................2-2

2.1.1 Removing the rear cover ............................................................. 2-2

2.1.2 Removing the mid cover ............................................................. 2-3

2.2 Air duct........................................................................................................2-4

2.2.1 Removing the air ducts ............................................................... 2-4

2.2.2 Installing the air ducts ................................................................. 2-5

2.3 Central Processing Unit (CPU) .................................................................2-7

2.3.1 Installing the CPU and heatsink .................................................. 2-7

2.4 System memory .......................................................................................2-11

2.4.1 Overview ................................................................................... 2-11

2.4.2 Memory Configurations ............................................................. 2-11

2.4.3 Installing a DIMM ...................................................................... 2-13

2.4.4 Removing a DIMM .................................................................... 2-13

2.5 (optional) Front bezel ...............................................................................2-14

2.5.1 Removing the front bezel .......................................................... 2-14

2.5.2 Installing the front bezel ............................................................ 2-16

iv

2.6 Storage devices........................................................................................2-19

2.6.1 Installing a 2.5” hot-swap SATA/SAS/NVMe storage device .... 2-20

2.6.2 Installing a 2.5” storage device to the rear bay ......................... 2-21

2.7 Expansion slot ..........................................................................................2-22

2.7.1 Installing an expansion card to the left PCIe riser card

bracket ...................................................................................... 2-23

2.7.2 Installing an expansion card to the right PCIe riser card

bracket ...................................................................................... 2-26

2.7.3 Installing an HBA/RAID card to the right PCIe riser card

bracket ...................................................................................... 2-30

2.7.4 Installing an OCP 3.0 card to the OCP 3.0 slot ......................... 2-32

2.7.5 Installing an M.2 (NGFF) card ................................................... 2-33

2.7.6 (optional) Installing the PFR module ......................................... 2-34

2.7.7 Configuring an expansion card ................................................. 2-35

2.8 Cable connections ...................................................................................2-36

2.9 Backplane cabling ...................................................................................2-37

2.10 Storage device configuration and cabling ............................................2-38

2.10.1 24 x NVMe storage device configuration and cabling .............. 2-39

2.10.2 16 x NVMe and 8 x SAS/SATA storage device configuration

and cabling ................................................................................ 2-40

2.11 Removable/optional components ...........................................................2-41

2.11.1 System fans .............................................................................. 2-41

2.11.2 Redundant power supply module.............................................. 2-43

2.12 Rail Kit Options ........................................................................................2-44

Chapter 3: Motherboard Information

3.1 Motherboard layout ....................................................................................3-2

3.2 Central Processing Unit (CPU) .................................................................3-5

3.3 Dual Inline Memory Module (DIMM) ..........................................................3-5

3.4 Jumpers ......................................................................................................3-6

3.5 Internal LEDs ............................................................................................ 3-11

3.6 Internal connectors ..................................................................................3-14

Chapter 4: BIOS Setup

4.1 Managing and updating your BIOS ..........................................................4-2

4.1.1 ASUS CrashFree BIOS 3 utility................................................... 4-2

4.1.2 ASUS EZ Flash Utility ................................................................. 4-3

4.1.3 BUPDATER utility ....................................................................... 4-4

4.2 BIOS setup program ..................................................................................4-6

4.2.1 BIOS menu screen ...................................................................... 4-7

4.2.2 Menu bar ..................................................................................... 4-7

v

4.2.3 Menu items..................................................................................4-8

4.2.4 Submenu items ........................................................................... 4-8

4.2.5 Navigation keys ........................................................................... 4-8

4.2.6 General help................................................................................4-8

4.2.7 Configuration fields ..................................................................... 4-8

4.2.8 Pop-up window............................................................................4-8

4.2.9 Scroll bar ..................................................................................... 4-8

4.3 Main menu ..................................................................................................4-9

4.4 Performance Tuning menu ......................................................................4-10

4.5 Advanced menu .......................................................................................4-12

4.5.1 Trusted Computing.................................................................... 4-12

4.5.2 Redfish Host Interface Settings................................................. 4-13

4.5.3 AMD CBS .................................................................................. 4-13

4.5.4 Onboard LAN Configuration ...................................................... 4-22

4.5.5 Serial Port Console Redirection ................................................ 4-23

4.5.6 CPU Configuration .................................................................... 4-25

4.5.7 PCI Subsystem Settings ........................................................... 4-26

4.5.8 USB Configuration .................................................................... 4-31

4.5.9 Network Stack Configuration..................................................... 4-32

4.5.10 NVMe Configuration .................................................................. 4-33

4.5.11 SATA Configuration .................................................................. 4-34

4.5.12 Offboard SATA Controller Configuration ................................... 4-34

4.5.13 APM Configuration .................................................................... 4-34

4.5.14 AMD Mem Configuration Status................................................ 4-35

4.5.15 T1s Auth .................................................................................... 4-36

4.5.16 Driver Health ............................................................................. 4-36

4.5.17 Third-party UEFI driver configurations ...................................... 4-37

4.6 Chipset menu ...........................................................................................4-38

4.7 Security menu ..........................................................................................4-39

4.8 Boot menu ................................................................................................4-43

4.9 Tool menu ................................................................................................. 4-44

4.10 Event Logs menu .....................................................................................4-45

4.10.1 Change Smbios Event Log Settings ......................................... 4-46

4.10.2 View Smbios Event Log ............................................................ 4-47

4.11 Server Mgmt menu ...................................................................................4-48

4.11.1 System Event Log ..................................................................... 4-49

4.11.2 BMC network configuration ....................................................... 4-50

4.11.3 View System Event Log ............................................................ 4-52

4.12 Exit menu .................................................................................................. 4-53

vi

Chapter 5: Driver Installation

5.1 Running the Support DVD .........................................................................5-2

Appendix

K14PA-U24 block diagram ..................................................................................... A-2

Notices .................................................................................................................... A-3

Service and Support ............................................................................................... A-7

vii

Safety information

Electrical Safety

• Before installing or removing signal cables, ensure that the power cables for the system

unit and all attached devices are unplugged.

• To prevent electrical shock hazard, disconnect the power cable from the electrical

outlet before relocating the system.

• When adding or removing any additional devices to or from the system, ensure that the

power cables for the devices are unplugged before the signal cables are connected.

If possible, disconnect all power cables from the existing system before you add a

device.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service

technician or your dealer.

Sécurité électrique

• Avant d’installer ou de retirer des câbles, assurez-vous que les câbles d’alimentation du

système et de tous les périphériques sont débranchés.

• Pour éviter tout risque de choc électrique, débranchez le câble d’alimentation de la prise

électrique avant de toucher au système.

• Lors de l’ajout ou du retrait de périphériques, vérifiez que les câbles d’alimentation sont

débranchés avant de brancher d’autres câbles. Si possible, déconnectez tous les câbles

d’alimentation du système avant d’y installer un périphérique.

• Si le bloc d’alimentation est endommagé, n’essayez pas de le réparer vous-même. Contactez

un technicien électrique qualifié ou votre revendeur.

viii

Operation Safety

• Any mechanical operation on this server must be conducted by certified or experienced

engineers.

• Before operating the server, carefully read all the manuals included with the server

package.

• Before using the server, ensure all cables are correctly connected and the power

cables are not damaged. If any damage is detected, contact your dealer as soon as

possible.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.

• If you encounter technical problems with the product, contact a qualified service

technician or your retailer.

This product is equipped with a three-wire power cable and plug for the user’s safety. Use

the power cable with a properly grounded electrical outlet to avoid electrical shock.

Sécurité de fonctionnement

• Toute opération mécanique sur ce serveur doit être effectuée par des ingénieurs certifiés ou

expérimentés.

• Avant d'utiliser le serveur, lisez attentivement tous les manuels fournis avec ce dernier.

• Avant d'utiliser le serveur, vérifiez que tous les câbles sont bien branchés et que les câbles

d'alimentation ne sont pas endommagés. Si des dommages sont détectés, contactez votre

revendeur dès que possible.

• Pour éviter les court-circuits, gardez les clips, les vis et les agrafes loin des connecteurs, des

slots, des interfaces de connexion et de la circuiterie.

• Évitez la poussière, l'humidité et les températures extrêmes. Placez le serveur sur une surface

stable.

• Si vous rencontrez des problèmes techniques avec votre produit, contactez un technicien

qualifié ou votre revendeur.

Ce produit est équipé d’un câble d’alimentation et d’une prise tripolaires pour la sécurité de

l’utilisateur. Utilisez le câble d’alimentation sur une prise électrique correctement reliée à la

terre pour éviter les chocs électriques.

ix

Heavy System

CAUTION! This server system is heavy. Ask for assistance when moving

or carrying the system.

Lithium-Ion Battery Warning

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

Restricted Access Location

This product is intended for installation only in a Computer Room where:

• Access can only be gained by SERVICE PERSONS or by USERS who have been

instructed about the reasons for the restrictions applied to the location and about any

precautions that shall be taken.

• Access is through the use of a TOOL, or other means of security, and is controlled by

the authority responsible for the location.

Emplacement d’accès restreint

Ce produit est destiné à être installé uniquement dans une salle informatique où :

• L’accès est uniquement accordé aux TECHNICIENS ou UTILISATEURS qui ont connaissance des

raisons de cette restriction et des précautions qui devraient être prises.

• L’accès se fait par le biais d’un OUTIL ou tout dispositif de sécurité, et est contrôlé par l’autorité

responsable de cet emplacement.

Système lourd

ATTENTION ! Ce serveur est un système lourd. Demandez de l'aide pour

déplacer ou transporter le système.

Avertissement sur les batteries Lithium-Ion

ATTENTION ! Danger d'explosion si la batterie n'est pas correctement

remplacée. Remplacer uniquement par une batterie de type identique ou

équivalent, comme recommandé par le fabricant. Jetez les batteries usagées

conformément aux instructions du fabricant.

x

To prevent exposure to the optical drive’s laser, do not attempt to disassemble or repair the

optical drive by yourself. For your safety, contact a professional technician for assistance.

CLASS 1 LASER PRODUCT

Optical Drive Safety Information

Laser Safety Information

Risque d'exposition dangereuse au laser. Ne tentez pas de démonter ou réparer le

lecteur de disque optique. Pour votre sécurité, faites réparer le lecteur de disque optique

uniquement par un prestataire de dépannage agréé.

Informations de sécurité concernant le lecteur optique

Informations de sécurité relatives au laser

PRODUIT LASER DE CLASSE 1

xi

About this guide

Audience

This user guide is intended for system integrators, and experienced users with at least basic

knowledge of configuring a server.

Contents

This guide contains the following parts:

1. Chapter 1: Product Introduction

This chapter describes the general features of the server, including sections on front

panel and rear panel specifications.

2. Chapter 2: Hardware Information

This chapter lists the hardware setup procedures that you have to perform when

installing or removing system components.

3. Chapter 3: Motherboard Information

This chapter gives information about the motherboard that comes with the server. This

chapter includes the motherboard layout, jumper settings, and connector locations.

4. Chapter 4: BIOS Setup

This chapter tells how to change system settings through the BIOS Setup menus and

describes the BIOS parameters.

5. Chapter 5: Driver Installation

This chapter provides instructions for installing the necessary drivers for different

system components.

xii

References

Refer to the following sources for additional information, and for product and software

updates.

1. ASUS Control Center (ACC) user guide

This manual tells how to set up and use the proprietary ASUS server management

utility. Visit asuscontrolcenter.asus.com for more information.

2. ASUS websites

The ASUS websites provide updated information for all ASUS hardware and software

products. Visit https://www.asus.com for more information.

Conventions

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this manual.

Typography

Bold text Indicates a menu or an item to select.

Italics

Used to emphasize a word or a phrase.

<Key> Keys enclosed in the less-than and greater-than sign

means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter

or Return key.

<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the

key names are linked with a plus sign (+).

Example: <Ctrl>+<Alt>+<Del>

Command Means that you must type the command exactly as

shown, then supply the required item or value enclosed in

brackets.

Example: At the DOS prompt, type the command line:

format A:/S

DANGER/WARNING: Information to prevent injury to yourself when trying to

complete a task.

CAUTION: Information to prevent damage to the components when

trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

This chapter describes the general features of the server. It

includes sections on front panel and rear panel specifications.

1

Product Introduction

Chapter 1: Product Introduction

1-2

If any of the above items is damaged or missing, contact your retailer.

1.1 System package contents

Check your system package for the following items.

Model Name RS520A-E12-RS24U

Chassis ASUS R2P-E 2U Rackmount Chassis

Motherboard ASUS K14PA-U24 Server Board

Component

24 x 2.5-inch Storage Device Trays or Dummy Trays

2 x 2.5-inch Storage Device Trays

4 x System Fans

Accessories 1 x CPU Heatsink

2 x AC Power Cable

Optional Items

1+1 Redundant 1200W/1600W 80PLUS Platinum Power Supply or

1+1 Redundant 1600W 80PLUS Titanium Power

2 x Riser card (16 NVMe configuration & 12 NVMe configuration)

1 x System redundant fan kit

1 x Friction Rail Kit or Ball-bearing rail kit

ASUS PIKE II 3008 card

ASUS RS520A-E12 Series 1-3

1.2 Serial number label

The product’s serial number contains 12 characters such as xxSxxxxxxxxx and printed on the

sticker at the server's front cover.

The correct serial number of the product is required if you need to request for support from

the ASUS Technical Support team.

xxSxxxxxxxxx

RS520A-E12-RS24U

1 2

3 4

RESET

Chapter 1: Product Introduction

1-4

1.3 System specifications

The ASUS RS520A-E12 Series features the ASUS K14PA-U24 server board. The server

supports AMD EPYC™ 9004 Series processors plus other latest technologies through the

chipsets onboard.

(continued on the next page)

Model Name RS520A-E12-RS24U

Motherboard K14PA-U24

Processor Support

1 x Socket SP5 (LGA 6096)

4th Genenration AMD EPYC™ processors with AMD 3D V-Cache

technology

AMD EPYC™ 9004 series (up to 400W)

Core Logic System on Chip (SoC)

Memory

Total Slots 24 (12-channel per CPU, 24 DIMM per CPU)

* May support to 2DPC, depends on AMD schedule

Capacity Maximum up to 6TB

Memory Type

DDR5 4800/4400/4000/3600 RDIMM / 3DS RDIMM

1 DPC up to 4800

2 DPC up to 4000 (1R+1R)

2 DPC up to 3600 (1R+2R)/(2R+2R)

* Please refer to www.asus.com for latest memory AVL update

Memory Size

256GB, 128GB, 64GB, 32GB RDIMM

256GB, 128GB, 64GB, 32GB 3DS RDIMM

* Refer to www.asus.com/support for more information

Expansion

Slots

Total PCI/PCIe/

PIKE Slots 5+1

Slot Type

Up to 5 PCIe Gen5 slots + 1 OCP3.0

2 x PCIe Gen5 x16, FHFL or 4 x PCIe Gen5 x8

1 x PCIe Gen5 x16, LP

1 x OCP Mezz. 3.0 Slot ( (PCIx`e Gen5 x16)

24x NVMe SKU

1 x PCIe Gen5 x8, LP + 1 x OCP3.0 (PCIe Gen5 x16)

(can’t support GPU)

16x NVMe SKU or 12x NVMe SKU

up to 5 PCIe Gen5 slots + 1 OCP3.0

2 x PCIe Gen5 x16, FHFL or 4 x PCIe Gen5 x8, FHFL

1 x PCIe Gen5 x8, LP

1 x OCP3.0 (PCIe Gen5 x16)

M.2 2 x M.2 (SATA signal or PCIe Gen5 x4 link) (Up to 22110)

microSD Card slot 1

Proprietary Slot 1 1 x PCIe x16 slot (Gen5 x8 link, for pike card only)

Proprietary Slot 2 -

ASUS RS520A-E12 Series 1-5

(continued on the next page)

Model Name RS520A-E12-RS24U

Storage

SATA Controller

CPU integrated

2 x M.2 connectors (support SATA3 6Gb/s or PCIe Gen5 x4 link)

1 x SATA controller (supports 2 x SATA3 6Gb/s)

SAS Controller

Optional kits:

ASUS PIKE II 3008 8-port SAS 12Gb/s HBA card

Broadcom MegaRAID 9560-16i

Storage

Bays

Storage Bay

Front bays:

24 x 2.5” hot-swap drive bays

- 24 x NVMe or

- 16 x NVMe + 8x SAS/SATA (from HBA/RAID card) or

- 12 x NVMe + 12x SAS/SATA

- 8 x NVMe + 16x SAS/SATA

Rear bays:

2 x 2.5-inch Storage Device Trays (SATA III)

* SAS support only from optional SAS HBA/RAID card

Backplane

connectors

12 x MCIO x2 (for NVMe)

6 x SlimSAS x4 (for SATA)

MB on-board

connectors

2 x M.2 connectors

8 x MCIO connectors

Default Cable Optional, in CPQ under the option “others”

NVMe upgrade

option

Support 24 x NVMe: 12 x NVMe cable

Support 16 x NVMe: 8 x NVMe cable

Support 12 x NVMe: 6 x NVMe cable

Networking

1 x Dual Port Intel I350-AM2 Gigabit LAN controller

1 x Management Port

Optional OCP Adapter:

Up to 100Gb/s Ethernet / InfiniBand Adapter

VGA BMC Integrated (Aspeed AST2600 256MB)

Graphic

4 x Single-wide GPU (FHFL) or

2 x Double-wide GPU (FHFL)

(Not supported in 24 x NVMe model)

Front I/O Ports 2 x USB 3.2 Gen 1 ports

1 x Power button

Rear I/O Ports

2 x USB 3.2 Gen 1 ports

1 x VGA port

1 x RJ-45 Mgmt LAN port

2 x RJ-45 1GbE LAN ports

Chapter 1: Product Introduction

1-6

*Specifications are subject to change without notice.

Model Name RS520A-E12-RS24U

Switch/LED

Front Switch/LED:

1 x Power Switch (w/LED)

1 x Reset Switch

1 x Location Switch (w/LED)

1 x HDD Access LED

1 x Message LED

LAN 1-2 LED

Rear Switch/LED:

1 x Port80 LED (Q-Code)

1 x Power Switch w/LED

1 x Location Switch w/LED

1 x Message LED

Security Options TPM-SPI Module (optional)

PFR Module (optional)

OS Support Please find the latest OS support from https://www.asus.com/.

Management

Solution

Software ASUS Control Center (Classic)

Out of Band

Remote

Management

On-Board ASMB11-iKVM for KVM-over-IP

Regulatory Compliance CE, RCM, FCC (Class A)

Dimension 840mm x 449mm x 88.1mm (2U)

33.07in x 17.68in x 3.47in

Net Weight Kg (CPU, DRAM &

HDD not included) 19.14Kg

Gross Weight Kg (CPU, DRAM

& HDD not included, Packing

include)

26.63Kg

Power Supply

(different configuration by region)

1+1 Redundant 1200W 80 PLUS Platinum Power Supply

Rating: 100-127/200-240Vac, 10A/8A (x2), 50/60Hz

1+1 Redundant 1600W 80 PLUS Platinum/Titanium Power

Supply

Rating: 100-127/200-240Vac, 12A/9.5A (x2), 50/60Hz

(240Vdc Only for China)

Environment

Operation temperature: 10°C ~ 35°C

Non operation temperature: -40°C ~ 60°C

Non operation humidity: 20% ~ 90% (Non condensing)

ASUS RS520A-E12 Series 1-7

1.4 Front panel features

The barebone server displays a simple yet stylish front panel with easily accessible features.

The power and reset buttons, LED indicators are located on the front panel.

Refer to section 1.7 LED information for the LED descriptions.

• Bay 1 to bay 24 supports NVMe for 24 NVMe configuration.

• Bay 5 to bay 20 supports NVMe; others support SATA/SAS* from HBA/RAID for 16

NVMe configuration.

• Bay 5 to bay 16 supports NVMe, others supports SATA/SAS* for 12 NVMe

configuration.

* SAS support only from HBA/RAID card.

24 x 2.5” Storage Bays

1 2

3 4

RESET

USB 3.2 Gen 1 ports Front panel LEDs & buttons

Handle

Bay 1 Bay 24

1 2

3 4

RESET

Front bezel

Bezel keylock

Bezel release latch

For extra security, a front bezel (purchased separately) can be installed to prevent

unauthorized physical access to the hard drives and power button.

Chapter 1: Product Introduction

1-8

• * This port is for ASUS ASMB11-iKVM only.

• The Q-Code LED provides the most probable cause of an error code as a starting point

for troubleshooting. The actual cause may vary from case to case.

• Refer to the Q-Code table for details.

1.5 Rear panel features

The rear panel includes the expansion slots, and system power sockets. The middle part

includes the I/O shield with openings for the rear panel connectors on the motherboard.

2 x 2.5” Storage Bays

VGA port

Lan port 1

Lan port 2

Location button

Power button

Management LAN port 1*

USB 3.2 Gen 1 ports

Redundant Power supply

and Power cord connector OCP 3.0 slot

Expansion slotsExpansion slots

Q-Code LED

Expansion slot

La pagina si sta caricando...

Asus RS520A-E12-RS24U Manuale utente

Asus RS520A-E12-RS24U Manuale utente

in altre lingue

Documenti correlati

Altri documenti