SLX 27780R Manuale utente

Marca: SLX

Modello: 27780R

Tipo: Manuale utente

Product Contents:

• Outdoor amplied digital aerial

• 3m Flylead (F-Type to Coax)

• Power adaptor

• Wall bracket/stand and ttings

• Power inserter

• Rubber boot

Outdoor Compact Digital TV Aerial

USER GUIDE

Introduction

Operating Instructions

overleaf

Part No.

27780R

The SLx Outdoor Compact Digital TV Aerial is

suitable for digital terrestrial television reception

(also known as DVB, DTT and Freeview™) in strong

signal areas and comes with a complete wall

mounting kit. It has been specically designed for

use with digital television receivers and has an

in-line amplier for a better performance.

Before you go any further, please check that you

are in a suitable digital signal area by visiting

www.digitaluk.co.uk or www.dtg.org.uk.

If you are in a weak or medium digital signal area

you may require a suitable high gain outdoor

TV aerial.

Page 1

Installing the aerial wall bracket

Wall

bracket

Universal joint

(adjustable)

Drill Holes

Wall plug

Screw

Page 2

1. Hold the wall bracket up to the wall and

carefully mark the positions of the centre of the

four holes. When xing to masonry walls screws

and wall plugs should be xed into bricks/stone

not into mortar courses.

2. Carefully drill 4 holes using a 6mm drill bit to a

depth of 30mm (or if you are using your own

wall plugs, use a suitable drill size and drill to

required width and depth).

3. Push the 4 wall plugs into the 4 holes.

4. Line up the 4 holes in the Aerial Stand with

the 4 holes you have just drilled in the wall.

Then screw each screw rmly into the lined

up holes.

5. Screw the Aerial on to the Universal Joint.

Then screw the Universal Joint on to the

Aerial Stand.

Before you permanently install the Aerial, it is

advisable to check that the proposed installation

location is suitable for receiving digital TV signals.

To check connect the Aerial to your equipment

as described oposite and hold the Aerial in the

intended position, switch on and scan for Digital TV

Stations on your TV/Set Top Box.

If Digital TV Stations can be received, the Aerial can

be permanently installed.

3m Fly-Lead

cable

(F-Type to

Coax)

(rear)

DTT Receiver

(rear)

Power

Adaptor

SLx Outdoor

Compact Digital

TV Aerial

(back view)

Power

Inserter

Plug directly into DTT Receiver.

If receiver is to far, use Male to Female Coax Lead (Not supplied)

Aerial in

▲ ▲

TV out

SCART

out

Antenna DC in

Receiver

(not supplied)

SCART Lead

Aerial in SCART in

▲

RF Aerial Flylead

(only use if

analogue signal

required*)

Connecting the Aerial

1. Place the Rubber Boot over the F-Plug on the

end of the supplied 3m Fly-Lead Cable. (see Fig 1.)

2. Connect the F-Plug on the end of the supplied

cable to the F-Socket on the back of the Aerial.

3. Connect the Coax plug on the other end of the

supplied cable into the Coax Socket marked

Antenna on the Power Inserter.

4. Insert the 3.5mm Jack Plug on the Power

Adaptor into the socket marked DC on the

Power Inserter, then plug the Power Adaptor

into a convenient Mains Socket.

5. Connect the Coax Plug marked Receiver on the

Power Inserter into the Antenna Input Socket on

your DTT (Freeview) Receiver. If your DTT

receiver is too far away, you may need to t a

male to Female Coax Lead (not supplied)

between the Receiver plug on the Power

Inserter and the Antenna Input Socket on your

DTT Receiver, switch on the Mains Supply.

6. Find the best reception position for the Aerial.

See www.digitaluk.co.uk for reception advice

for your area.

7. Switch on your TV/Set Top Box and re-scan for

Digital TV Stations.

8. The Universal Joint allows the Aerial position

to be adjusted. You may need to adjust the

Aerial position several times and re-scan for

Digital TV Stations to nd the optimum position.

Page 3

Rubber Boot

F-Connector

Aerial

Fly-Lead

Fig 1. F-Plug Connection

Problem Cause Action

No Picture Poor connections. Check all connections, make sure the

power inserter is properly

connected.

No power. Check that the power adaptor is

plugged in and that the Mains

supply socket is switched on.

Poor Picture or Digital signal

breaking up (Pixelated)

Poor connections. Check all connections, make sure the

power inserter is properly

connected.

Aerial is not aligned to the

transmitter or it is receiving a

reected signal from nearby

structures.

Check

www.digitaluk.co.uk

for reception advice or point the aerial

in the same direction as neighbouring

houses

The Aerials position has low

signal levels.

If the Aerial has been loft mounted or

mounted beneath guttering/eaves, try

mounting in an unobstructed outside

position.

Excess cable or low grade coax

cable has been used.

Make sure new digital coax cable has

been used throughout and ithat there

are no tight bends in the cabling.

Signal level uctuates or is

seasonally reduced (Tree foliage

growth in Spring/Summer).

Check that the signal is not obstructed

by buildings, nearby trees or satellite

dishes.

Distorted or Lines (Cross Chan-

nel Interference) across an

analogue picture, High Signal

level and Low Signal Quality

(Digital Bit Error Rate High).

In a strong signal area the signal

strength may need to be reduced by

tting an attenuator.

TECHNICAL SPECIFICATIONS

Frequency Range 47-230MHz and

470-862MHz

Ampliﬁer Gain 20+3dB

Power Supply 5V DC 40mA

Dimensions 160 x 200 x 40mm

Aerial & Bracket Weight 372g

For further information or any queries please contact

Technical Support: www.philex.com/support

Customer Care Line

Waste electrical and electronic products must

not be disposed of with household waste.

Please recycle where facilities exist. Check with

your Local Authority for recycling advice.

Reception hints and troubleshooting

Page 4

SLX 27780R Manuale utente

Marca: SLX

Modello: 27780R

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: SLX 27780R User manual

SLX 27780R Manuale utente

SLX 27780R Manuale utente

in altre lingue

Altri documenti