Megger ME-DLRO10A Manuale del proprietario

USER GUIDE

GUIDE DE L’UTILISATEUR

BEDIENUNGSANLEITUNG

GUIDA PER L’UTENTE

GUIA DEL USUARIO

M

DLRO®-10 & DLRO®-10X

Digital Low Resistance Ohmmeter

2

GSAFETY WARNINGS

n These safety warnings must be read and understood before the instrument is used.

n Whenever possible, circuits should be de-energised before testing.

If it is impossible to de-energise the circuit, (e.g. high voltage batteries cannot be switched off while their connections are tested) the user must

be aware of the dangers. The instrument terminals will become live when connected to the circuit. Therefore when used on hazardous voltages

custom Megger DH6, DH6-C test leads must be used.

n Testing inductive circuits can be hazardous:

After testing an inductive load there will be an amount of energy stored in the inductance. This energy is released in the form of a discharge

current. Disconnecting an inductive load while current is still flowing will cause a high voltage arc, which is a danger to both the user and the

item under test.

Although the DLRO 10 and DLRO 10X are not designed as transfromer ohmmeters the DLRO 10 is fitted with a DISCHARGE lamp, marked ‘I’,

which indicates that current is flowing in the C1-C2 loop. This lamp will flash at end of a test on an inductive load while a discharge current is

still flowing and will stop flashing when the current has decayed to less than 1mA. DLRO 10X uses a message on the display to achieve this.

For testing large inductive resistances the current carrying leads should be connected securely to the item under test before starting the test.

It is not recommended that duplex handspikes be used to carry out tests on inductive loads. If inadvertently using the DH4 handspikes on an

inductive load, the L1 lamp on the handspikes will flash amber while discharge current flows, thereby duplicating the function of the ‘I’ lamp on

the instrument. It is important to maintain contact until the L1 light stops flashing amber and turns green indicating the end of the test.

n This product is not intrinsically safe. Do not use in an explosive atmosphere.

n Please note. The neck strap is specifically designed to break if subjected to a strain of approximately 50 kg.

CAT II

Measurement category II: Equipment

connected between the electrical outlets and

the user’s equipment.

CAT III

Measurement category III: Equipment

connected between the distribution panel and

the electrical outlets.

CAT IV

Measurement category IV: Equipment connected

between the origin of the low-voltage mains

supply and the distribution panel.

Safety Warnings 2

General Description 4

General Operation - DLRO 10 5

Test Current Indicators 5

Noise Lamp 5

‘C’ & ‘P’ Indicators 5

‘V’ & ‘I’ Warning Indicators 5

General Operation - DLRO 10X 6

DLRO 10X Top Panel 6

DLRO 10X Main Menu Screen 6

Warning Messages 6

Noise 6

‘C’ & ‘P’ Indicators 6

External Voltage Warning 7

Discharge Current Warning 7

The Menuing System 7

Test Menu 7

Options Menu 7

Retrieve 7

Display 7

Download 8

Passbands 8

Set Clock 8

Delete Data 9

Storage 9

Range Menu 9

Entering Notes In The Memo Screen 10

Test Result Storage 10

Keypad Operation 11

Test Modes 12

Normal Mode 12

Automatic Mode 12

Continuous Mode 12

High Power Mode 12

Unidirectional Mode 13

Test Techniques & Applications 14

Testing Using DH4 Duplex Handspikes 14

Testing Using Handspikes Or Individual Leads. 14

Test Sequence 15

Test Lead Resistance 15

Overheating 15

Battery Module And Care 16

The Battery Module 16

Battery Charging 16

The Battery State Indicator 17

Standard Charging. 17

Slow Charging. 17

Standard Charging But At A Slow Rate. 17

There Is A Temperature Problem. 17

Input Voltage Too Low. 17

Battery Nearly Exhausted 17

Error: Reset 17

Overvoltage Problem 18

Specifications 19

Troubleshooting 21

Repair and Warranty 23

End of life disposal 24

Symbols used on the instrument

G Caution: Refer to accompanying notes

t Equipment protected throughout by Double or

reinforced Insulation (Class II)

c Equipment complies with current EU Directives

Do not dispose of in the normal waste stream

3

CONTENTS

The DUCTER DLRO 10 and DUCTER DLRO 10X make up a family of low resistance ohmmeters that measure resistances in the range from 0.1 µΩ to 2 kΩ.

Both instruments provide a maximum test current of 10 Amps d.c. which is automatically selected according to the value of resistance being tested. The

DLRO 10X allows you to override this automatic selection and select your own test current.

The measured value of resistance is output to the instrument display with indication of the units, µΩ, mΩ or Ω. The DLRO 10 uses a large LED display and

indicators to display the value and units respectively, while the DLRO 10X contains all the information on a clear backlit LCD display.

The use of a four terminal measurement technique removes the test lead resistance from the measured value and auto current reversal eliminates the

effect of standing voltages across the test sample. Additionally, before and during a test, test lead contact is monitored to further reduce the chance of

erroneous readings.

A resistance measurement takes approximately 2.5 seconds and comprises a measurement with forward current, reverse current and a display of the

average. On the DLRO 10X all three values are displayed, and optionally, the measurement may be limited to forward current only.

The instrument is powered by a rechargeable Nickel Metal Hydride (NiMH) battery, which permits one thousand 10 Amp tests to be completed on a

single charge. The battery module contains intelligent circuitry, which prevents damage to the battery from overcharging, and a battery state indicator. A

removable lid that is hinged at the back and held closed by magnetic catches covers the top panel. This lid may be removed if required by opening fully

and snapping out of its hinges.

Both instruments are protected against accidental connection to external voltages up to 600 V d.c. applied between any pair of the four terminals for up

to 10 seconds. Please note that applying 600 V to the potential terminals will cause some internal heating. Expect errors of up to 30 digits immediately

after the application of such voltage. Full accuracy will be restored within two to three minutes. Both instruments are supplied complete with a pair of

DH4 Duplex Handspikes with 1.2 m leads. Other lengths and terminations are available if required.

GENERAL DESCRIPTION

4

Press the On/Off switch to turn DLRO 10 on. All lamps will light, V and

I lamps will flash, the software version will be displayed and the Ω lamp

will light. If the test leads have not been connected to the test sample

the ‘C’ and ‘P’ lamps will also light. Press the On/Off button again to turn

the instrument off. If the instrument is not used for 5 minutes it will be

turned off automatically.

Adjust the brightness control to a comfortable level.

Select the Test mode by pressing the Mode button repeatedly. The

indicator lamps will cycle through the various Test modes in turn (see the

section on Test modes). Press the Test button to start a test.

Test Current Indicators

The test current is selected automatically by DLRO 10 and is indicated by

the lamps on the left of the panel. The measured value is displayed in the

main window and the units (µΩ, mΩ or Ω) are shown by the lamps to the

right of the window.

Noise Lamp

Noise in excess of 100 mV 50/60 Hz will light the ‘Noise’ lamp and

measurement accuracy cannot be relied upon.

‘C’ & ‘P’ Indicators

The ‘C’ lamp illuminates to indicate contact failure in the ‘C1-C2’ loop.

The ‘P’ lamp illuminates when there is a break in the P1-P2 loop.

‘V’ & ‘I’ Warning Indicators

If external voltage is applied to the terminals the ‘V’ lamp will flash. This is

a warning that the item under test is live and might be dangerous. A test

cannot be performed in this condition.

The ‘V’ lamp will light if more than 50 V. is applied between either

voltage terminal and a current terminal. If the voltage appears between

just the voltage terminals or just the current terminals the lamp will light

at 100 V peak or 5 V peak respectively.

Please note - The ‘V’ lamp will only indicate if a voltage appears

between terminals. The lamp will not operate if all terminals are at

the same high voltage. The lamp will not operate if the instrument

is turned off.

The ‘I’ lamp will light if a current greater than 1 mA is still flowing after

a test is completed. This suggests that an inductive load has been tested

and is still discharging. Do not disconnect the current loop until the ‘I’

lamp has gone out.

GENERAL OPERATION - DLRO 10

5

DLRO 10X Top Panel

All the controls needed to set up and operate DLRO 10X are located on

the top panel of the instrument.

To the left of the large LCD display are the controls for moving around the

display, controlling the menuing system and adjusting the display contrast

and backlight.

To the right of the display is the large Test button, Power On/Off button

and an alphanumeric keypad for entering notes relating to a test which

will be stored with the test results for later reference.

To turn your DLRO 10X on, press the On/Off button for approximately 1

second. Press again to turn the instrument off. If the instrument is not

used for 5 minutes it will be turned off automatically.

DLRO 10X Main Menu Screen

When first switched on DLRO 10X displays a copyright screen, followed by

the Main Menu screen.

This screen provides you with information such as percentage of battery

charge remaining, index number of the next test, number of tests already

stored and the current date and time.

This screen also provides access to the menuing system, through which

you set up your instrument and choose the desired test parameters.

Navigation of this menuing system is by means of the cursor control and

Enter key.

Warning Messages

The Main Menu screen will from time to time also contain certain warning

messages

Noise

Noise in excess of 100 mV 50/60 Hz will activate the message ‘Noise’

at the bottom of the display. Above this level accuracy cannot be relied

upon.

‘C’ & ‘P’ Indicators

A good measurement requires both the current carrying circuit and the

voltage detection circuit to be completed by the item under test. DLRO

10X checks for this continuity. If there is poor continuity in either circuit a

message will appear at the bottom of the display. This will read “P OPEN

CIRCUIT” if the voltage contacts are high resistance, “C OPEN CIRCUIT” if

6

GENERAL OPERATION - DLRO 10X

the current circuit is not made or “CP OPEN CIRCUIT” if both circuits are

inadequate. Check the contacts, since a measurement cannot be made if

any of these messages is visible on the display.

External Voltage Warning

If external voltage is applied to the terminals a message “EXT VOLTS” will

flash on the display. This is a warning that the item under test is live and

might be dangerous. A test cannot be performed in this condition.

The “EXT VOLTS” message will flash if more than 50 V. is applied

between either voltage terminal and a current terminal. If the voltage

appears between just the voltage terminals or just the current terminals

the message will appear at 100 V peak or 5 V peak respectively.

Please note - The message will only appear if a voltage appears BETWEEN

terminals. The message will not appear if all terminals are at the same

high voltage. The message will not operate if the instrument is turned off.

Discharge Current Warning

A message CURRENT FLOW will appear if a current greater than 1 mA is

still flowing after a test is completed. This suggests that an inductive load

has been tested and is still discharging. Do not disconnect the current

loop while the discharge warning is showing.

The Menuing System

Use the Left and Right arrows of the cursor control to highlight the menu

required. Press the Down cursor control to see the options available on

that menu. Select the required option using the cursor control and press

Enter to set that option. Depending on the menu item selected the display

will either present further options or will return to the main menu screen.

Test Menu

This sub-menu selects the test mode. Only one mode can be active at a

time and the active mode is displayed below the heading TEST. (See Test

Modes later in this manual for details of each mode.)

Options Menu

The Options menu has five options that are not related to each other, as

shown below.

Retrieve

allows the recall of stored results to the display or a PC.

Display

recalls each test, in sequence, to the instrument display

starting with the latest stored result.

Use the cursor

control Up

and Down

controls to step later or earlier respectively through the stored results.

Alternatively, if you know the index number of the test you wish to

display, type the number on the keypad and press Enter.

An asterisk (*) next to the word “MEMO” means that there are notes

attached to this result. Press the right cursor control to view the notes.

Download

GENERAL OPERATION - DLRO 10X

7

causes the entire contents of the data store to be output

to the RS232 port to the left of the display. A copy of

AVO Download Manager, which facilitates downloading

and formats the data, is supplied.

Downloading data does not cause the stored data to be

erased from memory. To clear data from memory see

“Delete Data” below.

Please note - DLRO 10X also makes data available via the RS232 Port in

real time and is suitable for printing on a self-powered serial printer.

The output has the following form:

TEST NUMBER

TEST TYPE

DD MM YY HH MM

01/01/00 00:33

FORWARD RESISTANCE

REVERSE RESISTANCE

AVERAGE RESISTANCE

SELECTED CURRENT

UPPER LIMIT

LOWER LIMIT

PASS/FAIL

The last three lines will only appear if passbands have been set

Passbands

This option allows you to set upper and lower limits between which the

test result average must fall if it is to be signalled as a Pass (a long tone

from the buzzer). Readings outside these limits will be signalled as a Fail (a

short tone from the buzzer).

Values are entered via the keypad complete with decimal points, where

applicable, and including µ or m (See section on the Alphanumeric

Keypad). It is not necessary to enter the Ω symbol. The upper limit must

be less than or equal to 2000.0 Ω and the lower limit must be less than

the upper limit.

After completing the upper limit press Enter. DLRO 10X will check that

valid numbers have been entered and will move to the lower limit.

Complete this limit and press Enter. DLRO 10X will check that valid

numbers have been entered and will display the option to ENABLE or

DISABLE the passbands.

Highlight your choice and press Enter. You will return to the Main Menu

screen.

Note: Passbands will remain enabled or disabled until you enter this

screen and change the selection. If all that is required is to change Pass-

bands from ENABLED to DISABLE or vice versa, enter the PASSBAND screen

and press Enter until the ENABLED / DISABLED choice is shown at which

time you may change the selection.

Set Clock

This option sets the real time clock date and time settings as well as

setting the date format. When you enter this screen the current date, time

and date format will be displayed.

Use the cursor control Up and Down arrows to adjust the highlighted

data. Step to the next item by using the Right cursor control arrow.

The row below DD MM YY HH MM contains respectively the date, the

GENERAL OPERATION - DLRO 10X

8

month, the two-digit year, the hour of the day in 24-hour notation and

the minute. These must be entered in this sequence regardless of the date

format you wish to use.

The lower DD/MM/YY shows the current date format. Pressing the cursor

control Up arrow will cycle through the available options DD/MM/YY, MM/

DD/YY or YY/MM/DD.

The bottom line shows the current setting of date and time. This is

updated when you press Enter to exit the Set Clock function. However,

tests already stored prior to changing the date format will retain the old

format.

Delete Data

Select Delete Data if you wish to clear DLRO 10X’s memory of stored data.

In case you have selected this Option by accident you will be asked to

confirm that you wish to delete the data; the default is NO. Change this

to YES and press Enter if you wish to delete all data.

Please note - ALL stored data will be deleted.

Storage

The Storage option sets the default for data storage. It may be set to

always store data or never to store data. Highlight the desired option at

the bottom of the screen and press Enter.

With the exception of tests carried out in Continuous mode, at the end of

each test you have the option to change the default by selecting STORE or

NO STORE at the bottom of the results screen.

At the end of a test, if memory is full this STORE / NO STORE message will

change to MEMORY FULL and no more tests will be stored.

Data is stored indefinitely if a charged battery pack is fitted. If the main

battery becomes exhausted or is removed, data is maintained for a period

of 4 days by an internal backup battery. When a charged battery pack is

refitted, the backup battery will recharge to full capacity within 1 week.

Range Menu

DLRO 10X uses a test current between 100 µA and 10 A to measure the

resistance of the item under test. If set to AUTO, DLRO 10X will select the

current according to the resistance it detects. (see Specifications, Ranges)

However, in some cases it may be desirable set a maximum test current.

If this is so, move the cursor to the desired current and press Enter.

Six test currents are available; 10 A, 1 A, 100 mA, 10 mA, 1 mA and 100

µA. Selecting the 10 A maximum will have the same effect as selecting

AUTO.

The Main Menu screen will show the active current range beneath the

RANGE heading.

ENTERING NOTES IN THE MEMO SCREEN

At the end of each test, (with the exception of a test in Continuous

mode), you can select the STORE or NO STORE option to store the test

results or not. Select the desired option using the cursor control. This

overrides the default setting under Options, Storage for one test only.

If you wish to add comments to the test results, instead of pressing Enter,

GENERAL OPERATION - DLRO 10X

9

TEST OPTIONS RANGE

NORM AUTO

DD MM YY HH MM

09/10/00 15.08

DD MM YY

09/10/00 12.02

briefly press one of the twelve keys on the keypad. You will enter a memo

screen that allows you to enter up to 200 characters of alphanumeric

information concerning the test. When you have entered all information

press Enter and the measurement and memo will be stored regardless of

whether STORE or NO STORE was selected.

If you do not wish to add notes and are happy to accept the default

STORE / NO STORE setting you may press the Test button and a new test

will be started.

TEST RESULT STORAGE

Each test is numbered, starting at test 1. This test number is incremented

automatically, as each result is stored. The test result memory can store a

maximum of 700 tests, each being identified by its test number, date and

time.

It is advisable to retrieve all data to a PC and then to delete all data before

the test number reaches this maximum. Deleting the data will reset the

test number to 1. This will save loss of data.

KEYPAD OPERATION

The 12 key keypad is similar to those used on mobile telephones in that

each key is capable of producing one of several characters depending on

the number of times the key is pressed.

The keypad is used to enter data into the Memo field.

Pressing the blue key

marked 9/A changes

the function of the keyboard between alpha and numeric modes.

In alpha mode a full height flashing vertical bar (|) indicates the cursor.

The keys 2 to 9 will produce the letter shown on the keys depending on

the number of presses. For example if the 2 key is pressed once an ‘A’ will

appear, twice and a ‘B’ will appear etc.

The 0 key produces a space.

The 1 key is a destructive backspace.

In numeric mode a half height flashing bar (‘) indicates the cursor. The

keys marked 1 - 9 and 0 produce that number when pressed. Press the

respective key briefly to enter the desired number. Pausing will cause the

cursor to move on to the next character. If a key is held down it will auto-

repeat.

The key at the bottom right hand corner of the keypad marked with a

dot is a special key that produces 20 special symbols. Each press will

sequentially produce the character shown on next page:

GENERAL OPERATION DLRO 10X

10

. Decimal point or full stop

Ω Ohms symbol

m lower case m (abbreviation for milli)

µ Symbol for micro

# Symbol known as hash or pound and commonly used as

shorthand for “number”

% Percent sign

( Left round bracket

) Right round bracket

- Hyphen, dash or minus sign

/ Slash

: Colon

@ “at” symbol;

√ Tick mark

! Exclamation mark

? Question mark

$ “Dollar” symbol

= “Equals” sign

< “Less than” symbol

> “Greater than” symbol

* Asterisk

GENERAL OPERATION DLRO 10X

11

TEST MODES

DLRO 10 has 4 test modes which are selected by repeated presses of the

Mode button. At the end of each test, DLRO 10 will display the average

of the values obtained with forward and reverse current.

DLRO 10X has 5 modes. On DLRO 10X these modes are selected from the

TEST menu using the cursor control and Enter key. At the end of a test,

DLRO 10X will show three resistance values; that obtained with forward

current, that obtained with reverse current and the average value.

Normal mode

Normal mode makes a single measurement of the resistance of the

sample using forward and reverse current

Please note that in this mode both the current and voltage leads

must be connected across the test sample before the Test button is

pressed. To make another measurement, ensure the test leads are

connected and press the test button.

Automatic mode

If Automatic mode is selected, your instrument will remain in a state of

readiness waiting for both the current AND voltage measuring leads to

be connected to the test piece. When this is done, a forward and reverse

current test will be started automatically.

To make another measurement simply break contact with the test sample

and remake contact.

For example, if measuring joints in a long bus bar, you may leave the

current circuit connected at opposite ends of the bus bar. Simply making

contact with voltage probes across the joint(s) you wish to measure will

then activate the measurement.

Continuous mode

Continuous mode requires the connections to be made before pressing

the Test button. Your instrument will then repeat its forward and reverse

measurements and display the results approximately every 3 seconds until

contact is broken or the Test button is pressed.

Inductive mode

DLRO 10 and DLRO 10X are able to make d.c. resistive measurements on

loads that exhibit an inductive component using the test mode indicated

by the inductor symbol on the DLRO 10, or by using the inductive mode

on the DLRO 10X.

When measuring inductive loads it is essential that the current

carrying leads are securely clamped to the item being tested and

that they are not removed before any stored charge has been

discharged at the end of the test. Failure to comply with these

instructions might result in an arc being produced, which might be

dangerous for the instrument and the operator.

Having selected inductive mode, connect all four leads to the item being

tested and press the Test button.

DLRO will check that all four leads are in adequate contact with the test

piece and will then apply a test current and try to find the correct range.

The display will show 1 - - followed by 1 - - - -. During this time you may

see the current range increasing or decreasing. On the DLRO 10 the “I”

lamp will flash and the message “Current Flowing” will appear on the

DLRO 10X display.

After a short time resistance readings will appear on the display, reducing

gradually over aperiod of time until eventually a stable reading will be

obtained.

TEST MODES

12

The time required for a stable reading may vary from a few seconds up

to several minutes depending on the inductance and resistance of the

test sample. There is no time limit for the inductive mode test, which will

continue until the operator presses the Test button.

When the test is terminated, the “I” lamp will remain illuminated on the

DLRO 10 or the message “Discharging” will appear on the DLRO 10X

display until any stored energy has discharged. When these messages are

extinguished it should be safe to disconnect the “C” leads.

However, the discharge indicator is an active electronic device and should

not be relied upon. You should observe your organisation’s operating

procedures.

At the end of the test both instruments will display the measured

resistance, the DLRO 10 will flash the relevant current lamp while the

DLRO 10X will display the test current used on the display.

Please note:- In inductive mode the 10A test current will not be

used.

Undirectional mode

On the DLRO 10X only, this mode makes the measurement as in

automatic mode but using forward current only.

This mode speeds up measurments on samples that are known to be free

of any standing voltages or thermal emfs. However the accuracy of the

reading may be degraded by any thermal emfs but should not be worse

than 0.2% ± 30 digits.

Since current is only applied in the forward direction, in this mode only a

single resistance value will be displayed.

A test may be repeated by breaking contact and reapplying the test

probes or by pressing the Test button.

Test Modes

13

TESTING USING DUPLEX TEST LEADS FITTED WITH INDICATOR

LAMPS

Each handspike is marked with the letter P. This indicates the potential

terminals. These should be the ‘inside’ contacts when making a

measurement (as shown in the next section ‘Testing Using Duplex

Handspikes or Individual Leads’).

One of the DH4 handspikes is fitted with two lamps marked L1 and L2

and an extra lead. This lead should be plugged into the 4 mm socket next

to the main terminals on the right hand side of the instrument. These

lamps provide information to the operator, which would otherwise only

be available on the instrument display. The meaning of these lamps is

described below.

For example, using the DH4 or DH4-C Duplex Handspikes or any

connecting test leads with indicator lights with the DLRO 10 in AUTO test

mode:

1. Press the TEST button on the instrument.

2. Lamp L1 will illuminate a continuous red to indicate contact

failure. See the instrument panel for details if required.

3. When all four contacts connect, L1 will extinguish.

4. No lamps will show during the test unless contact fails.

5. Lamp L2 will light a continuous green when current flow has

decayed to less than 1 mA to signal end of test.

6. Removing the probes will extinguish the green L2 (end of test) and

Light the red L1 (no contact).

Since your DLRO always ensures good contact before applying the full

test current, there will be no ‘splash’ to erode the contact tips. However,

should the tips become worn or blunted, they can be simply replaced by

pulling out the worn tips and inserting new ones.

TESTING USING DUPLEX HANDSPIKES OR INDIVIDUAL LEADS.

Connect the four leads as shown.

If using Duplex Handspikes ensure that the probe marked P is inside the

C probes.

Note: When used on hazardous voltages Megger DH6 test leads must

be used.

TEST TECHNIQUES & APPLICATIONS

14

C

CPP

DLRO 10 and DLRO 10X (no passbands)

Lamp L1 Lamp L2 Meaning

Red Off Inadequate contact at C

and/or P contacts

Flashes Red Off Voltage present between

contacts (DLRO10 Only)

Off Green Current less than 1 mA and

test complete.

DLRO10X ONLY if pass bands set

Off Green Measurement Pass

Off Red Measurement Fail

TEST SEQUENCE

Pressing the TEST button starts the test sequence.

Contact resistance is checked by passing 100 µA through the C1-C2

loop and checking that the voltage is less than 4 V. Then passing 80 µA

through the P1-P2 loop and checking that the voltage is less than 250

mV. If either value is exceeded the respective lamp or warning message

will be displayed.

When all faults have been rectified the test current is increased until

the voltage on P1-P2 is within the 2 mV to 20 mV range. This current

is then applied in a forward and then reverse direction to obtain two

measurements.

Both measurements are displayed by DLRO 10X along with the average,

while the DLRO 10 displays the average only.

If the combined resistance of the current leads and test sample is greater

than 100 mΩ, testing at 10 A will not be possible.

A 1.9 mΩ resistor will then be tested at the next lowest current

(1 A) and the result will be shown as 1.900 mΩ instead of

1.9000 mΩ.

TEST LEAD RESISTANCE

For testing at 10 A, the combined resistance of the current leads must

not exceed 100 mΩ. This will ensure that the voltage drop in the leads is

less than 1 volt and will enable 10 A testing under worst case conditions.

If you wish to limit test current to no more than 1 A, on DLRO 10 use

current leads with a resistance of about 1 Ω, or on DLRO 10X select 1A as

the maximum test current on the RANGE submenu.

OVERHEATING

When performing rapidly repeated tests at 10 A, using current leads with

a combined resistance of 100 mΩ, 10 W of heat will be dissipated in

the leads and 30 W within your instrument. If the ambient temperature

is high this will cause internal overheating and the message “hot” will

appear on the instrument display and testing will be halted.

After a few minutes to cool down, testing will be allowed to continue.

If this is a persistent problem, use current leads with a higher resistance

(e.g. 200 mΩ to 300 mΩ). This will reduce the generation of internal heat.

TEST TECHNIQUES & APPLICATIONS

15

BATTERY MODULE AND CARE

THE BATTERY MODULE

The battery module contains nickel-metal-hydride cells and has a built-

in battery-management system that controls charging and monitors

discharge. This provides a high capacity, low-weight battery system, which

can be recharged at any time. It is not possible for the user to over-charge

or over discharge the battery. For your own convenience it is best to

charge it regularly to keep it topped up, but leaving it in a discharged

state will do no harm.

On the front of the battery module are two buttons and a

10-segment LED display.

To find the amount of charge in your battery module, whether connected

to your DLRO or separate, press the Battery Condition Button. The Battery

State indicator will light between

1 and 10 segments signifying between 10% and 100% charge

respectively. After a few seconds this display will automatically go out.

BATTERY CHARGING

Please note - The battery should only be charged within the

temperature range 0°C to 45°C. Fast charging will not be allowed

if the temperature is below 10°C. Fast charging causes the

temperature of the battery to rise. If the temperature exceeds 45°C

the charging rate will be reduced automatically.

To charge the battery, your battery module must be removed from the

instrument. Remove the module by pressing on the raised circular area of

the retaining clips and pull the top of the clip away from the instrument

body. The module now unplugs from the base of the instrument.

Plug in the charger or connect to a 12 volt vehicle-type battery using

the ‘cigar lighter’ lead provided. The LED “Battery State” indicator will

light and show movement when the battery is charging. The battery

may be recharged before it has been fully discharged. It will normally be

recharged to 90% of capacity within 21/2 hours. Full charge may take

up to 4 hours before indicating that the battery is full depending on

the initial state of the battery. When charging is complete the battery

management circuitry will switch off so that over-charging is prevented.

Your battery module can be safely used in a partially charged state and

will not suffer if stored in a discharged state. However, you may wish

to have a spare battery that can be interchanged with the one in use to

provide continuous use of your DLRO.

As the battery ages, it may start to loose its capacity. In this case the

battery module has a slow charge facility which is activated by pressing

the Slow Charge button while switching on the charger supply until the

indicator bars start to move. This method of charging can take up to

48 hours and so is best reserved for a weekend or a period when the

instrument is not required to be used.

A fully charged battery, even if not used, will self discharge over a period

of several weeks (faster at higher temperatures). Always check the

“Battery State” indicator before starting work. A fully charged battery

will light all segments. A fully discharged battery will light no segments.

Slow Charge Battery Condition Battery State Indicator

16

Please note that all batteries suffer a reduced life if exposed to

constant high temperatures. A constant temperature of 30°C will

probably cause the battery to fail in less than 5 years. 40°C will

shorten its life to 2 years.

THE BATTERY STATE INDICATOR

The Battery State Indicator provides information on the amount of charge

in the battery, but is also used to signal other conditions as follows:

Standard Charging.

The battery module is charging at its

standard rate.

Slow Charging.

The battery module is charging at its slow

rate.

Standard charging but at a slow

rate.

The battery has been set to charge at its

standard rate but, because the battery has

become hot, it has switched charge rates

to a lower rate while the battery cools down. Wait for the temperature to

drop and/or move to a cooler location.

Not charging. There is a temperature problem.

The battery is too hot or too cold and

charging has therefore been interrupted

until the battery returns to a temperature

between 0°C and 45°C (32°F and 113°F)

Input Voltage Too Low.

The charger supply is not supplying sufficient

voltage to the battery module to charge the

batteries.

Battery nearly exhausted

The battery capacity is very low. Recharge

it.

Error: Reset

An error has occurred within the battery

module. The circuitry is resetting. Wait a

few moments and the fault should clear.

Overvoltage problem

The charging supply voltage is too high. Disconnect the charger and

rectify the fault.

BATTERY MODULE AND CARE

17

Fast

Slow

Flashing Slow

Flashing

Rapid

Flashing

WARNING

Connecting to greater than 15 volts can cause permanent

damage to the battery module.

The DLRO10 and DLRO10X can also be powered from

a mains / line power supply unit the DLRO10LPU. This

is available as an accessory, details can be found in the

Accessories section of this user guide

BATTERY MODULE AND CARE

18

Ranges

DLRO 10 DLRO 10X

Display Measurement 4

1/2 digit seven segment LED

Range and Safety LED Indication

Measurement Mode Manual, Auto, Continuous, Inductive Manual, Auto, Continuous,

Inductive, Unidirectional.

Control Fully Automatic Fully Automatic with manual

override of maximum current

Speed <3s for forward & reverse current and to display average

Test Method Single cycle reversing d.c. ratiometric measurements and average result calculated.

Test Current Accuracy 10%

Output Current Stability <10 ppm per second @ 10 mA

<100 ppm per second at higher currents

SPECIFICATIONS

19

Large backlit LCD

Full Scale Resolution Accuracy Full Scale Volts Test Current

Resistance ResistanceInduction Induction

1,9999 mΩ

19,999 mΩ

199,99 mΩ

1,9999 Ω

19,999 Ω

199,99 Ω

1999,9 Ω

0,1 µΩ

1 µΩ

10 µΩ

100 µΩ

1 mΩ

10 mΩ

100 mΩ

±0,2%±0,2 µΩ 20 mV

20 mV

200 mV

20 mV

200 mV

10 A

1 A

100 mA

10 mA

1 mA

100 µA

1 A

100 mA

10 mA

1 mA

100 µA

±0,2%±2 µΩ

±0,2%±20 µΩ

±0,2%±0,2 mΩ

±0,2%±2 mΩ

±0,2%±20 mΩ

±0.2%±0.2 Ω

SPECIFICATIONS

20

DLRO 10 DLRO 10X

Maximum Lead Resistance 100 mΩ total for 10A operation irrespective of battery condition.

Voltmeter Input Impedance > 200 kΩ

Hum Rejection Less than 1% ± 20 digits additional error

with 100 mV peak 50/60 Hz. on the potential leads.

Warning will show if hum or noise exceeds this level.

Data Transfer Real Time or from storage via RS232

Storage 700 tests

Memo Field Up to 200 characters per test via

integral alphanumeric keypad.

Battery Capacity 7 Ah NiMH rechargeable.

Life Typically 1000 x 10 A tests before recharge

Recharge Via External 90V - 260 V 50/60 Hz charger or from 12 to 15 V d.c. supply

Charging Time 2.5 hours to 90% capacity, 4 hrs for full charge

Temperature Operation +5°C to +45°C (41°F to 113°F) at full specification.

-10°C to +50°C (14°F to 122°F) at reduced accuracy

Storage -30°C to +70°C (-22°F to 158°F)

Calibration 20°C (68°F)

Coefficient <0.01% per oC from 5°C to 40°C (<0.006% per °F from 41°F to 104°F)

Standard charging 0°C to +45°C (32°F to 113°F)

Fast charging +10°C to +45°C (50°F to 113°F)

Humidity Max 90% RH @ 40°C (104°F) non-condensing

Altitude Max 2000m (6562 ft.) to full safety specifications

Safety In accordance with IEC61010-1 600 V Category III - only when DH6 leads are used

EMC In accordance with IEC61326-1

Operation inaccuracies Refer to www.megger.com

Dimensions 220 x 100 x 237 mm (8.6 x 4 x 9.5 in)

Weight 2.6 kg (5 3/4 lb.) including battery module

La pagina sta caricando ...

Megger ME-DLRO10A Manuale del proprietario

Questo manuale è adatto anche per

Megger ME-DLRO10A Manuale del proprietario

in altre lingue

Altri documenti