Ruark Audio R3 Compact Music System Manuale utente

Tipo
Manuale utente
R3 Compact Music System
R3 Comapct Music System
User guide
EN
Important information about
the AC power adapter
Model DYS836-140285W-K
Input 100-240V~50/60Hz 1.0A MAX
Output 14.0V 2.85A
Class II, Efciency Level VI
• This AC adapter is for audio & video equipment use
only and complies with IEC 60065 safety standard.
• The supplied 3-pin plug adapter complies with
BS 1363-1 and the supplied 2-pin plug adapter
complies with EN 50075.
• Before using the AC adapter, ensure the mains voltage
is within the rated supply voltage range.
• The output power taken from this AC adapter must not
exceed its rated output power.
• DO NOT disassemble or modify the AC adapter.
• DO NOT drop or throw the AC adapter.
• The external exible cable cannot be replaced and if
the cord is damaged, the AC adapter must be replaced.
• DO NOT expose the AC adapter to dripping or
splashing water, and do not place objects lled with
liquids, such as vases, on or near the device.
• DO NOT leave the AC adapter in a hot location, such as
near re or under strong sunlight.
• Unplug the AC adapter during lightning storms or
when unused for long periods of time to prevent
damage.
• Ensure that the AC adapter is readily accessible when
plugged into the mains. If an abnormal condition occurs
while using it, immediately turn off the connected
device and disconnect the mains adapter from the
mains.
• DO NOT dispose this AC adapter as general household
waste or unsorted municipal waste. Dispose of it
according to local regulations.never cover ventilation
openings on the device.
Safety and regulatory
information
Read this user guide and follow all instructions, it will help you set up
and operate your product properly.
Heed all warnings and keep this user guide for future reference.
Do not attempt to use a damaged device as this could result in a
dangerous electric shock.
Do not open the unit or remove any panels to expose the electronics.
No user serviceable parts inside.
Refer all servicing to qualied service personnel. Servicing is required
when the device has been damaged in any way, such as when any
power cord, or power plug is damaged, liquid has been spilled or
objects have fallen into the device, the device has been exposed to
rain or moisture, does not operate normally, or has been dropped.
This device is intended to be operated ONLY from the AC voltages
listed on the back panel or included AC mains adapter. Operation from
voltages other than those indicated may cause irreversible damage to
the device and void the product warranty.
Ensure that the mains plug or mains connector into the unit is readily
accessible in case disconnection from the mains is required.
The AC mains adapter, mains plug, or mains connector must be
removed from the socket to completely disconnect the system from
AC mains power.
Do not place any naked ame sources, such as lighted candles, on or
near the device. Do not install near any heat sources such as radiators,
stoves, or other devices that produce heat.
Avoid exposure to extreme heat or cold.
Only use attachments/accessories specied for this device. Make no
modications to the system or accessories. Unauthorised alterations
may compromise safety, regulatory compliance, and system
performance.
Only use the supplied aerial or an approved replacement.
To reduce the risk of re or electrical shock, do not expose the device
to rain or moisture. Do not expose this device to dripping or splashing,
and do not place objects lled with liquids, such as vases, on or
near the device. As with any electronic products, use care not to spill
liquids into any part of the system. Liquids can cause a failure and/or
a re hazard.
Disconnect this device from AC mains power during lightning storms
or when unused for long periods of time to prevent damage to this
device.
To prevent risk of re or electric shock, avoid overloading AC mains
power outlets or extension cords.
Long-term exposure to loud music may cause hearing damage. It is
best to avoid extreme volume when using headphones, especially for
extended periods.
Do not install this device in a conned space. Always leave a space
of at least 10cm around the device for ventilation and ensure that
curtains or other objects never cover ventilation openings on the
device.
This device is labelled in accordance with European Directive
2012/19/EU concerning waste electrical and electronic
equipment. This symbol indicates that the product or
associated batteries should not be disposed of as general
household waste. As with any electrical equipment, please
dispose of it according to local regulations.
CE COMPLIANCE INFORMATION
This product conforms to all EU Directive requirements as applicable by
law. Hereby, Ruark Audio, declares that this device complies with the
essential requirements and other relevant provisions of the European
Radio Equipment Directive 2014/53/EU.
You can download the full CE Declaration of Conformity at
www.ruarkaudio.com/doc/R3doc.pdf
EN
Specifications
Amplifiers and drivers
2 × 75mm Ruark NS+ drivers
30W Class AB power amplier
Enhanced digital 3D audio processor
Tuner
DAB, DAB+ and FM Tuner with RDS
75 Ohm F-type DAB/FM aerial connector
CD player
CD, CD-ROM, CD-R/RW
MP3, WMA, AAC up to 320 kbit/s
Digital audio
Internet radio, Spotify Connect, Amazon Music, Deezer,
TIDAL, UPnP™ DLNA
Wi-Fi 802.11a/b/g/n supports WEP, WPA & WPA2 security
MP3, WMA, AAC, FLAC, WAV
Bluetooth: V4.0 SBC, AAC, A2DP, aptX
Inputs and outputs
Digital optical input (TOSLINK) 24-bit 192kHz
Line input (RCA) 2.3Vrms max
Line out (RCA) 2.0Vrms
Ethernet (RJ45)
USB 2.0, 5W (5V 1A)
3.5mm stereo jack headphone output
Power
AC mains adapter input: 100-240V AC 50/60Hz 1A
AC mains adapter output: 14V DC 2.85A
Nominal consumption: 5W
Standby consumption: 2W
Remote batteries: 2 x 1.5V AAA
Physical
H167 x W420 x D220mm (H6.6 x W16.5 x D8.7in)
5.3kg (11.7lbs)
Specication and design subject to modication without
notice.
Ruark Audio assumes no responsibility for any errors that
may appear in this manual and the information contained
in it may change without notice.
Troubleshooting
For help with your product, please refer to the FAQ
(Frequently Asked Questions) page in the support area of
our website.
For more information visit www.ruarkaudio.com/support.
What’s in the box
Ensure that all parts listed below are in
the box.
If any part is missing, do not use the R3
and contact us directly if purchased in
the UK, or your Ruark Audio dealer if
purchased outside the UK.
1. R3
2. Remote control
3. Remote batteries (2x 1.5V AAA)
4. Antenna spanner
5. Telescopic antenna
6. AC power adapter
7. Plug(s) for AC power adapter*
8. Quick start guide
If possible, please retain the carton and
all packaging materials.
1
3
4
5
6
8
72
* The number and type of plug adapters
supplied will vary according to region.
EN
Controls
9. STANDBY
10. CONTROL KNOB / SELECT
Rotate to adjust volume from a Now Playing screen
Rotate to browse menus, tracks or station lists*
Press to SELECT
11.
– press to skip to next station or track, press
and hold to fast forward. In standby, press to
increase display brightness.
12.
– press to skip to previous station or track,
press and hold to rewind. In standby, press to
decrease display brightness.
13. PRESET – press to recall a saved station or
playlist, press and hold for two seconds to save a
station or playlist
14. SOURCE – press to change audio source
15.
– press to play/pause a track or mute audio
inputs and radio
16. MENU – press to view the menu
17. BACK – press to return to the previous menu or list
screen
18. INDICATOR LIGHT
Indicates your music system is on and ashes
when Bluetooth is ready to pair or when using the
remote.
*You can also press
or to browse menus, tracks,
sources or station lists.
How long you press a key is important
Press = tap or press and immediately release
Press and hold = press and release after two seconds
9
11
12
13
14
10
16
17
15
18
Remote
19. STANDBY
20.
SOURCE – press to change audio source.
21. INCREASE VOLUME
22.
/ SELECT – press to play/pause a track,
mute/unmute radio or to select a menu item.
23.
– press to skip to previous station or
track, press and hold to rewind. In standby,
press to decrease display brightness.
24.
– press to skip to next station or track,
press and hold to fast forward. In standby,
press to increase display brightness.
25. DECREASE VOLUME
26.
BACK – press to return to the previous
menu or list screen.
27.
MENU – press to view the menu.
28.
PRESET – press to recall a saved station
or playlist, press and hold for two seconds to
save a station or playlist.
29. PRESET 1
30. PRESET 2
31. PRESET 3
+
-
+
-
21
25
19
26
29
31
30
23
20
22
27
24
28
EN
40
39 41
42
46
45
44
43
343332 35 36 3837
Overview
32. Remote receiver
33. Ambient light sensor
34. CD eject button
35. OLED display
36. Controls
37. CD loading slot
38. 75mm Ruark NS+ drivers
39. USB C (5V 1A)
40. Optical input
41. Ethernet
42. DAB-FM antenna
43. DC power input (14V 2.85A)
44. Line in (phono)
45. Line out (phono)
46. Headphone out (3.5mm jack)
Getting started
1 Insert batteries into remote control
2 Connect the aerial
Fit the telescopic aerial to the DAB/FM antenna socket
on the back of your R3 and gently tighten it using the
supplied spanner.
3 Connect to AC mains power
Fit the correct plug for your region to the mains adapter;
it will “click” into place. Connect the mains adapter to the
DC power socket on the back of your R3, then connect it
to the mains socket.
4 Switch on
Press to turn the R3 on.
5 Select language
Rotate the CONTROL KNOB until your preferred choice
is highlighted, then press SELECT.
6 Setup wizard
Follow the setup wizard to congure the clock and
connect to your network.
To start the setup wizard, rotate the CONTROL KNOB to
highlight YES and then press the knob to SELECT.
If you choose NO, your R3 will start without conguring
the time/date and network settings.
7 Select a source
When your setup is complete, your R3 will display
a menu with a list of the available sources. Use the
CONTROL KNOB to choose a source and press
SELECT.
8 Enjoy your music!
App control
You can also control your R3 using UNDOK. Find it on
the Apple/Android app store.
For more information visit www.ruarkaudio.com/app
EN
Common functions
Switch on and to standby
Press STANDBY to turn your music system on. Press
again to switch to standby.
Now Playing screens
Unless you’re adjusting a setting, the screen will look
similar to the example below with the clock above and
station/track/album/artist information below.
The on-screen icons below are shown when their
respective functions are active.
Alarm Sleep timer
Shufe Repeat
Menu screens
The menus enable you to set the various options
such as adjusting the bass and treble. To change a
setting, press MENU to display the list of available
options, rotate the CONTROL KNOB to highlight the one
you wish to change, then press the knob to conrm your
selection.
System
Audio
Network
Date and time
Brightness
Language
Browsing menus, track and station lists
To change settings – press MENU
To scroll through options – rotate CONTROL KNOB
To select option – press CONTROL KNOB
To exit menu – press MENU or wait for a few seconds
To return to the previous menu/list – press BACK
How long you press a key is important
Press = tap or press and immediately release
Press and hold = press and release after two seconds
Adjust volume
Rotate the CONTROL KNOB from any Now Playing
screen.
Speaker volume and headphone volume are adjusted
separately, so when headphones are plugged in the
volume is shown as Volume (HP).
NOTE: rotating the CONTROL KNOB when a menu or
track/station list is displayed will scroll through the menu
and not change the volume.
Change audio source
Press SOURCE to view the current source, rotate the
CONTROL KNOB to cycle through the list of sources,
then press the knob to select one currently displayed.
(You can also press SOURCE repeatedly to cycle through
the list of sources instead of rotating the knob.)
Pause track or mute audio
Press and then press again to resume listening.
Play next/previous track
Press to skip to the next track in the folder or album,
press to skip to the start of the current track, press
again to skip to the previous track.
Fast forward or rewind track
Press and hold or (may not work with Bluetooth).
Change FM radio station
Press or to seek the next or previous station.
Change DAB radio station
Press or to tune to the next or previous station.
You can also view the multiline station list by selecting
MENU > Station list.
Change station or track information
Change the station/track information displayed by
selecting one of the options from MENU > Info.
Save radio station preset
Press and hold PRESET until ‘Save preset’ is shown
then rotate the CONTROL KNOB to choose the preset
number and press the knob to save the current station.
Presets are either marked with the station name,
frequency or as ‘[Not set]’.
If you save a station over an existing preset, the new
station will replace it.
Recall radio station preset
Press PRESET, rotate the CONTROL KNOB to scroll
through the preset station list, then press the knob to
select a station.
To return to the previous menu level or station list,
press BACK
EN
Connect a Bluetooth device
When you change the source to Bluetooth, your R3 will
attempt to automatically connect to the last connected
device. If you have not yet paired your device or the
previous device is not available, your R3 will enter into
pairing mode.
To disconnect the current device and connect a new one,
select MENU > Connect device.
Headphones
Connect your headphones to the 3.5mm stereo jack
socket on the front of your R3.
Headphone volume is adjusted independently from
speaker volume, so when headphones are plugged in the
volume is shown as Volume (HP).
USB charging
The USB socket on your R3 is rated at 5W (5V 1A)
and will power most smart devices and USB powered
accessories.
Music streaming services
Spotify Connect
Use your phone, tablet or computer as a remote control
for Spotify. Go to spotify.com/connect to learn how.
Amazon Music
For more details, visit www.amazon.com
Deezer
For more details, visit dzr.fm/airable
TIDAL
For more details, visit tidal.com/try-now
The range of supported music services may change
without notice.
Please note that: MENU > System > Audio means
press MENU, select System and nally select Audio
System settings
Bass and treble
MENU > System > Audio > Bass or Treble level
Loudness
Loudness automatically boosts the treble and bass
frequencies at lower volumes.
MENU > System > Audio > Loudness
3D sound
3D widens the stereo sound stage and creates a more
immersive and involving sound.
MENU > System > Audio > 3D
Date and time
MENU > System > Date and time
The time and date are automatically synchronised with
national time signals broadcast over DAB, network
and FM (FM time synchronisation may not always be
available).
You can also set the time manually by turning auto
update off and change the time and date format.
Display brightness
MENU > System > Brightness
Independently adjust the brightness of the display when
your R3 is on and in standby.
When the brightness is set to 0 the display will
automatically switch off after a few seconds. The display
will then briey illuminate whenever any key is pressed.
You can also adjust the standby brightness when your R3
is in standby by pressing
or .
Language
MENU > System > Language
Change the menu language.
Software update
MENU > System > Software update
Your R3 is set to automatically check for software
updates. If one is available, you will be asked whether
you want to download and install it.
CAUTION: Disconnecting the power during a software
update could permanently damage your R3.
Factory reset
MENU > System > Factory reset
Resets all settings and clears presets.
EN
Currently saved settings are marked with an asterisk ( )
Setup wizard
MENU > System > Setup wizard
Runs the setup wizard to guide you through setting up
the clock and network.
Inactive standby
Your R3 is set to automatically switch itself to standby
if there is no audio for more than 20 minutes. To change
this select MENU > System > Inactive standby.
Network wizard
For a guided process to help you connect to a wired or
Wi-Fi network, select MENU > System > Network >
Network wizard.
Network profiles
Your R3 will automatically attempt to connect to any
network it has previously connected to.
To see the list of saved networks, select MENU >
System > Network > Network profile. To delete an
unwanted network, highlight it, press the CONTROL
KNOB and select YES.
Keep network connected
MENU > System > Network > Keep connected
Choose whether your R3 always remains connected to
your network, even in standby (default). We recommend
you set it to keep connected as it will ensure your R3
is always accessible using Spotify or DLNA music
streaming. We also recommend this if you have set your
clock to update from Network.
System information
Shows details of your R3 including the software version,
and unique radio ID code.
Advanced network settings
There are other advanced network settings for
experienced users for manual conguration or diagnosing
and xing network problems.
For more information visit
www.ruarkaudio.com/support.
FM radio
When listening to FM, your R3 displays the station name
and other RDS/RBDS* programme information when
available.
*Radio Data System/Radio Broadcast Data System
Change station
Press or to automatically tune to the next
available FM station. If RDS/RBDS is unavailable the
frequency is displayed instead.
Scan setting
You can change the scan setting to only stop at stations
with a strong signal by selecting Menu > Scan setting >
Strong stations only.
Programme information
Choose from radio text, programme type, frequency,
signal strength and date by selecting MENU > Info.
Manual tune
Select MENU > Manual tune then either rotate the
CONTROL KNOB or press or to change the
frequency.
Save preset
You can store 10 FM stations in your preset list. The
station name will be stored only when RDS/RBDS is
available. See ‘Common functions’ section.
Recall preset
See ‘Common functions’ section.
Mono
As an FM signal becomes weaker, the level of hiss will
increase. To reduce this, select Menu > Mono.
To further reduce hiss on weaker FM stations,
we recommend turning 3D sound OFF
EN
DAB radio
When listening to DAB/DAB+, your R3 displays the
station name and other DLS* programme information
when available.
The rst time you use your R3, or if the station list is
empty, it will automatically perform a full scan to identify
available stations.
*Dynamic Label Segment
Change station
Press or to tune to the next/previous station.
Station list
To view a list of available DAB stations select MENU >
Station list or press or . Highlight the station you
wish to listen to and press SELECT.
Programme information
Choose from radio text, programme type, signal
strength, signal format and date by selecting MENU >
Info.
Save preset
You can store 10 DAB stations in your preset list. See
‘Common functions’ section.
Recall preset
See ‘Common functions’ section.
Station order
The DAB station list can be ordered by Alphanumeric,
Ensemble or Valid. Alphanumeric puts the stations
in alphabetical order, Ensemble groups stations from
the same broadcaster together, Valid shows available
stations rst and places invalid stations (marked with ‘?’)
last.
To change station order, select Menu > Station order
and select Alphanumeric (default), Ensemble or Valid.
Invalid stations have ‘?’ in front of the station name
Station scan
If the station list is empty the radio will automatically
perform a full scan as soon as you switch to DAB.
In any case, we recommend you do a full scan from time
to time to update the station list because:
New stations sometimes become available
Stations close or may no longer be received
Reception was poor during the original scan (for
example the aerial wasn’t properly tted)
You move the radio to a different region
To do a full scan, select MENU > Scan.
Remove weak or invalid stations
Weak (burbling) or invalid stations have ‘?’ in front of the
station name and can be removed by selecting MENU >
Prune invalid.
Internet radio
Your R3 can play thousands of internet radio stations
and podcasts from all over the world (internet connection
required).
Main menu
The rst time you listen to internet radio you will see the
main menu for this mode.
If you have listened to internet radio stations on your R3
before, it will automatically play the last listened station.
Last listened
To access a list of recently listened to stations select
MENU > Last listened.
When you use your R3 for the rst time, the list will be
empty.
Station list
You can browse or search the extensive list of stations
by selecting MENU > Station list and selecting from the
various options, including genre, location and popularity.
Now playing information
The station name is shown along with additional
information like artist and track name. To change what
is displayed select MENU > Info and choose from radio
text, genre, signal quality, track name, location, and date.
EN
Search for a station
Search for a station by selecting MENU > Station list >
Stations > Search stations and then entering the name
of the station you’re looking for.
Podcasts
Many stations will have associated podcasts which
you can browse and search for just like internet radio
stations.
Mute
Press to mute and press again to resume listening.
Save a preset
You can store 10 Internet radio stations in your preset list.
See ‘Common functions’ section.
Recall a preset
See ‘Common functions’ section.
DLNA media streaming
You can also stream audio to your R3 from a Digital
Living Network Alliance (DLNA) compatible media
server. This is where you browse for music on the server
itself and play it through your R3. There are many apps
available for Mac, iOS, Linux, Android, Windows phone,
etc that will turn your smartphone, tablet or laptop into a
DLNA media server.
With DLNA media streaming, your R3 functions as a
Digital Media Renderer (DMR) so you browse for music
on your smartphone or laptop and then stream it to your
R3 over your network.
Your R3 will automatically change to DMR mode when
you select your R3 as your chosen player – DMR is not a
mode that can be selected using the SOURCE key.
Similarly, all the Now playing information will be
controlled by the server so there are no settings you can
change.
For more details refer to the documentation for your
device or app or visit www.ruarkaudio.com/support.
DLNA media streaming requires that your R3 is connected
to your network so we recommend that you set it to keep
network connected. See system settings section.
EN
Bluetooth
Your R3 supports aptX for CD quality streaming. It will
automatically connect to your bluetooth device using the
highest quality connection supported by your device.
Pairing your Bluetooth device
When you have changed the source to Bluetooth, wait
until Awaiting connection... is shown and the indicator
light on top ashes.
Use the Bluetooth setup on your smart device to pair and
connect it to your R3. It will appear in the list of paired
devices as Ruark R3. When connected, BT Connected +
your device name (eg Ozzie’s phone) is displayed.
If you do not connect within a few minutes, your R3 will
stop attempting to connect and show No connection. To
connect, select MENU > Connect device.
Connecting your Bluetooth device
As soon as you switch to Bluetooth, your R3 will display
Connecting as it attempts to connect to the last device it
was paired with.
If that device isn’t available, it displays Awaiting
connection... To connect to your R3, ensure the
Bluetooth function on your device is on and select Ruark
R3 from the paired devices list on your Bluetooth device.
Play audio
Once connected, audio from your Bluetooth device
will play through your R3. For more information on
playing audio from your Bluetooth device, refer to your
device’s documentation.
NOTE: you may need to select your Ruark R3 or
Bluetooth as your audio output on your device.
Pause track
Press and then press again to play.
Skip track
Press or to skip to the next or previous track
Adjust volume
We recommend that you adjust the volume on your
Bluetooth device so that the playback volume is about
the same as other sources. You can then use the volume
control on your R3 to adjust overall playback volume.
Now Playing information
Artist, album and track name will show if your Bluetooth
device and app support Bluetooth metadata. You can
also show the name of the connected device. Select
what is shown from MENU > Info.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340

Ruark Audio R3 Compact Music System Manuale utente

Tipo
Manuale utente