Apollo TI6VGA Manuale utente

TI6VGA

Pentium II Apollo Pro

ATX Motherboard

User's Manual

Version 1.0A

ii TI6VGA User’s Manual

Copyright Notice

This publication is protected by copyright and all rights are reserved. No

part of it may be reproduced or transmitted by any means or in any form,

without prior consent of the original manufacturer.

The information in this document has been carefully checked and is

believed to be accurate. However, the original manufacturer assumes no

responsibility for any inaccuracies that may appear in this manual. In no

event will the original manufacturer be liable for direct, indirect, special,

exemplary, incidental, incidental or consequential damages resulting

from any defect or omission in this manual, even if advised of possibility

of such damages. The material contained herein is for informational

purposes only.

Acknowledgments

Award is a registered trademark of Award Software International, Inc.

IBM, PS/2 are trademarks of International Business Machines

Corporation.

Intel and Pentium are registered trademarks of Intel Corporation.

Apollo Pro is a trademark of VIA Technologies.

Microsoft Windows is a registered trademark of Microsoft Corporation.

All other product names or trademarks are properties of their respective

owners.

Contents

TI6VGA User’s Manual iii

Contents

Chapter 1 Introduction....................................................1

Chapter 2 Specifications..................................................2

Chapter 3 Hardware Description ...................................4

3.1 Processor...................................................................................6

3.2 L2 Cache ...................................................................................6

3.3 Main Memory............................................................................6

3.4 BIOS..........................................................................................8

3.5 Onboard AGP Slot.....................................................................8

3.6 Winbond W83781D Hardware Monitoring IC..........................8

3.7 Onboard Multi-I/O ....................................................................8

3.8 Interrupt Request (IRQ) Lines...................................................9

3.9 Onboard PCI-IDE......................................................................9

3.10 DMA Channels........................................................................9

3.11 I/O Port Address Map............................................................10

3.12 Onboard Audio......................................................................10

Chapter 4 Configuring the Motherboard ....................11

4.1 CPU Frequency Setting...........................................................13

4.2 Clear CMOS Select: JP6 .........................................................13

4.3 JP2(7-8): SDRAM Clock Select..............................................14

4.4 CPU Host Frequency Force Selector: JP4...............................14

Chapter 5 Installation....................................................15

5.1 I/O Connectors ........................................................................17

5.2 J1: PS/2 Keyboard and PS/2 Mouse Connectors.....................17

5.3 J2: ATX Power Supply Connector..........................................18

5.4 J3: Floppy Drive Connector ....................................................18

5.5 IDE1, IDE2: EIDE Connectors...............................................19

5.6 J4, J6: Serial Ports...................................................................20

5.7 J5: Parallel Port Connector......................................................20

5.8 J7: Game Port, Mic In/Line In/Line Out..................................21

5.9 J13, J14: CD-ROM Audio In Connectors................................21

5.10 J11, J18: CPU and Chassis Fan Power Connectors...............21

5.11 J12: IrDA Connector.............................................................22

5.12 USB1: USB Connector..........................................................22

Contents

iv

TI6VGA User’s Manual

5.13 J17: Wake on LAN Connector...............................................22

5.14 J20: Front Bezel Connectors..................................................23

Chapter 6 BIOS Configuration.....................................25

6.1 BIOS Introduction ...................................................................28

6.2 BIOS Setup..............................................................................28

6.3 Standard CMOS Setup.............................................................30

6.4 BIOS Features Setup................................................................33

6.5 Chipset Features Setup.............................................................36

6.6 Power Management Setup .......................................................39

6.7 PNP/PCI Configuration...........................................................42

6.8 Load BIOS Defaults ................................................................44

6.9 Load Setup Defaults.................................................................44

6.10 Integrated Peripherals............................................................45

6.11 Supervisor / User Password...................................................47

6.12 IDE HDD Auto Detection......................................................48

6.13 Save & Exit Setup..................................................................49

6.14 Exit Without Saving...............................................................49

Chapter 7 Audio Driver Installation Guide.................51

Chapter 8 System Monitor Utility ................................62

Appendix..........................................................................69

A. Slot 1 Retention Mechanism.....................................................69

B. Additions & Errata....................................................................70

Chapter 1 Introduction

TI6VGA User’s Manual 1

Chapter 1 Introduction

This manual is designed to give you information on the TI6VGA

motherboard. It is divided into the following sections:

•

••

•

Introduction

•

••

•

Specifications

•

••

•

Hardware Description

•

••

•

Configuring the Motherboard

•

••

•

Installation

•

••

•

BIOS Configuration

•

••

•

Audio Driver Installation Guide

•

••

•

System Monitor Utility

Checklist

Please check that your package is complete and contains the items below.

If you discover damaged or missing items, please contact your dealer.

 The TI6VGA Motherboard

 1 IDE ribbon cable

 1 floppy ribbon cable

 1 CD containing a system monitoring utility, 82596 Bus Master

IDE driver and utilities.

Chapter 2 Specifications

2 TI6VGA User’s Manual

Chapter 2 Specifications

The TI6VGA is a high-performance ATX Apollo Pro motherboard with

a Slot 1 connector for Pentium



II processors. It offers flexibility in terms

of CPU frequency and main memory type and size. The main features of

the motherboard consist of the following:

CPU Socket

Slot 1

Processor

Intel Pentium II 233/266/300MHz (66MHz / Klamath)

Intel Pentium II 333MHz (66MHz / Deschutes)

Intel Pentium II 300/350/400/450MHz (100MHz / Deschutes)

Intel Celeron 266/300/300A/333MHz (66MHz)

L2 Cache

CPU integrated L2 cache

Main Memory

Three 168-pin DIMM sockets

or Two 168-pin DIMM sockets and

64MB SDRAM on board

Memory types: Extended Data Output (EDO) DRAM, SDRAM

(Synchronous DRAM)

Memory size: 8MB, 16MB, 32MB, 64MB, 128MB

Chipset

VIA’s Apollo Pro chipset with built-in PCI-IDE

Super I/O

Onboard super I/O is a Winbond 83877TF that supports:

z

Two 16550 UART compatible serial ports

z

One parallel port (ECP/EPP compatible)

z

One floppy controller (2.88MB compatible)

z

One IrDA port

PCI Bus Master IDE Controller (Ultra DMA/33)

Onboard PCI Bus Master IDE (Ultra DMA/33) controller with two

connectors for up to four IDE devices in two channels, supporting

faster data transfer rates, enhanced IDE devices such as Tape Backup

and CD-ROM drives, PIO Mode 3/4 and Bus Mastering Ultra

DMA/33 (You have to install the Bus Master IDE driver to enable this

feature.)

Chapter 2 Specifications

TI6VGA User’s Manual 3

BIOS

Award BIOS with ISA Plug and Play (PnP) extension, DMI, bootable

CD-ROM and power-management features. The BIOS is Y2K (Year

2000) compliant.

Mouse Connector

PS/2 type

Keyboard Connector

PS/2 type

USB Connector

2 ports on board

Win95-shut-off

Allows shut-off control from within Windows 95

Onboard Audio

The onboard audio consists of the Creative ES1373 Chip + AC97.

With a PCI Bus Mastering interface with DOS compatibility, it

supports 32 voices wavetable, surround sound, 3D audio, and audio

effects such as reverb and chorus. Creative ES1373 uses single,

shareable PCI interrupt and is PC97 compliant.

Onboard AGP Slot

The AGP (Accelerated Graphics Port) slot supports AGP compliant

VGA cards to achieve rich 3D and video graphics display. AGP is a

platform bus specification that enables 3D graphics capabilities

including support for z-buffering, alpha blending and faster texture

mapping.

Expansion Slots

Four 32-bit PCI slots

Three 16-bit ISA slots

One AGP slot

Form Factor

ATX, 12” x 7.87 (30.5cm x 20cm)

Chapter 3 Hardware Description

4 TI6VGA User’s Manual

Chapter 3 Hardware Description

This chapter briefly describes each of the major features of the TI6VGA

motherboard. The layout of the board in Figure 1 shows the location of

the key components. The topics covered in this chapter are as follows:

3.1 Processor....................................................................................6

3.2 L2 Cache....................................................................................6

3.3 Main Memory............................................................................6

3.4 BIOS..........................................................................................8

3.5 Onboard AGP Slot.....................................................................8

3.6 Winbond W83781D Hardware Monitoring IC..........................8

3.7 Onboard Multi-I/O.....................................................................8

3.8 Interrupt Request (IRQ) Lines...................................................9

3.9 Onboard PCI-IDE......................................................................9

3.10 DMA Channels........................................................................9

3.11 I/O Port Address Map............................................................10

3.12 Onboard Audio ......................................................................10

Chapter 3 Hardware Description

TI6VGA User’s Manual 5

Figure 1: Layout of the TI6VGA Motherboard

Remarks: The TI6VGA comes with 3 DIMM sockets or 2 DIMM

sockets with 64MB SDRAM on board.

Chapter 3 Hardware Description

6

TI6VGA User’s Manual

3.1 Processor

The TI6VGA motherboard is designed to take an Intel Pentium II

processor running 233/266/300/333/350/400/450MHz or an Intel

Celeron processor running 266/300/333MHz with its Slot 1 processor

connector.

3.2 L2 Cache

The L2 cache is integrated in the Pentium II processor.

3.3 Main Memory

The TI6VGA motherboard supports three 168-pin DIMM (Dual In-line

Memory Module) sockets to form a memory configuration from 8MB to

384MB.

It can also come with two DIMM sockets and 64MB SDRAM

on board.

DIMM modules can be 8MB, 16MB, 32MB, 64M and128MB

in SDRAM. In populating the DIMM sockets, any socket can be

populated first. Refer to the following table on how to do the memory

configuration.

NOTE

: Use SDRAM modules with PC100 specification when running

100MHz CPU bus speed. With 66MHz CPU bus speed, SDRAM

modules with PC66 or PC100 specification can be used.

(DIMM1) (DIMM2) (DIMM3) Total Memory

8MB ----- ----- 8MB

16MB ----- ----- 16MB

32MB ----- ----- 32MB

64MB ----- ----- 64MB

128MB ----- ----- 128MB

8MB 8MB ----- 16MB

16MB 8MB ----- 24MB

32MB 8MB ----- 40MB

64MB 8MB ----- 72MB

128MB 8MB ----- 136MB

8MB 8MB 8MB 24MB

16MB 8MB 8MB 32MB

32MB 8MB 8MB 48MB

64MB 8MB 8MB 80MB

128MB 8MB 8MB 144MB

16MB 16MB ----- 32MB

32MB 16MB ----- 48MB

Chapter 3 Hardware Description

TI6VGA User’s Manual 7

64MB 16MB ----- 80MB

128MB 16MB ----- 144MB

16MB 16MB 8MB 40MB

32MB 16MB 8MB 56MB

64MB 16MB 8MB 88MB

128MB 16MB 8MB 152MB

16MB 16MB 16MB 48MB

32MB 16MB 16MB 64MB

64MB 16MB 16MB 96MB

128MB 16MB 16MB 160MB

32MB 32MB ----- 64MB

64MB 32MB ----- 96MB

128MB 32MB ----- 160MB

32MB 32MB 8MB 72MB

64MB 32MB 8MB 104MB

128MB 32MB 8MB 168MB

32MB 32MB 16MB 80MB

64MB 32MB 16MB 112MB

128MB 32MB 16MB 176MB

32MB 32MB 32MB 96MB

64MB 32MB 32MB 128MB

128MB 32MB 32MB 192MB

64MB 64MB ----- 128MB

128MB 64MB ----- 192MB

64MB 64MB 8MB 136MB

128MB 64MB 8MB 200MB

64MB 64MB 16MB 144MB

128MB 64MB 16MB 208MB

64MB 64MB 32MB 160MB

128MB 64MB 32MB 224MB

64MB 64MB 64MB 192MB

128MB 64MB 64MB 256MB

128MB 128MB 128MB 384MB

Chapter 3 Hardware Description

8

TI6VGA User’s Manual

3.4 BIOS

The BIOS on the TI6VGA motherboard provides the standard BIOS

functions plus the following additional features:

1. ISA Plug and Play (PnP) Extension

Unlike PCI cards that are Plug and Play, ISA cards require setting

jumpers to resolve hardware conflicts. To make a computer system

PnP, an ISA PnP standard is established and supported by new

operating systems, such as Windows 95. Under Windows 95, the

motherboard BIOS must have an ISA PnP extension to support new

ISA PnP cards.

2. Power Management

The power management feature provides power savings by slowing

down the CPU clock, turning off the monitor screen and stopping the

HDD spindle motor. The BIOS fully conforms to ACPI (Advanced

Configuration and Power Interface) specification.

3.5 Onboard AGP Slot

The AGP (Accelerated Graphics Port) slot supports AGP compliant

VGA cards to achieve rich 3D and video graphics display. AGP is a

platform bus specification that enables 3D graphics capabilities including

support for z-buffering, alpha blending and faster texture mapping.

3.6 Winbond W83781D Hardware Monitoring IC

The W83781D is a hardware status monitoring IC that is used to monitor

several hardware parameters including power supply voltages, fan

speeds, and temperatures, which are very important for a high-end

computer system to work stable and properly. The 48-pin LQFP-package

IC is fully software compatible with the Intel LANDesk Client Manager.

3.7 Onboard Multi-I/O

The onboard multi-I/O chip, Winbond 83877TF, supports a keyboard

controller, two serial ports, one parallel port, one floppy controller and

one IrDA port. The serial ports are 16550 UART compatible. The

parallel port features high-speed EPP/ECP mode. The floppy controller

supports up to 2.88MB format.

Chapter 3 Hardware Description

TI6VGA User’s Manual 9

3.8 Interrupt Request (IRQ) Lines

There is a total of 15 IRQ lines available on the motherboard. Peripheral

devices use an interrupt request to notify the CPU for the service

required. The following table shows the IRQ lines used by the devices on

the motherboard:

Level Function

IRQ0 System Timer Output

IRQ1 Keyboard

IRQ2 Interrupt Cascade

IRQ8 Real Time Clock

IRQ9 Software Redirected to Int 0Ah

IRQ10 Reserved

IRQ11 Reserved

IRQ12 Reserved

IRQ13 Co-Processor

IRQ14 Primary IDE

IRQ15 Secondary IDE

IRQ3 INTERRUPT

IRQ4 Serial Port #1

IRQ5 INTERRUPT

IRQ6 Floppy Disk Controller

IRQ7 Parallel Port #1

3.9 Onboard PCI-IDE

The PCI-IDE controller, 82596 chip, supports PIO mode 3/4 and bus

mastering Ultra DMA/33. The peak transfer rate of PIO mode 3/4 can be

as high as 17MB/sec. Using HDDs that support Ultra DMA/33, the peak

transfer rate can reach 33MB/sec. There are two IDE connectors -

primary IDE and secondary IDE. With two devices per connector, up to

four IDE devices can be supported.

3.10 DMA Channels

There are seven DMA channels available on the motherboard; only

DMA2 is used by the floppy controller. In the case that ECP mode on the

parallel port is utilized, DMA1 or DMA3 will be used.

Chapter 3 Hardware Description

10

TI6VGA User’s Manual

3.11 I/O Port Address Map

Each peripheral device in the system is assigned a set of I/O port

addresses which also becomes the identity of the device. There is a total

of 1K port address space available. The following table lists the I/O port

addresses used on the motherboard.

Address Device Description

000h - 01Fh DMA Controller #1

020h - 03Fh Interrupt Controller #1

040h - 05Fh Timer

060h - 06Fh Keyboard Controller

070h - 07Fh Real Time Clock,, NMI

080h - 09Fh DMA Page Register

0A0h - 0BFh Interrupt Controller #2

0C0h - 0DFh DMA Controller #2

0F0h Clear Math Coprocessor Busy Signal

0F1h Reset Math Coprocessor

1F0h - 1F7h IDE Interface

2F8h - 2FFh Serial Port #2(COM2)

378h - 3FFh Parallel Port #1(LPT1)

3F0h - 3F7h Floppy Disk Controller

3F8h - 3FFh Serial Port #1(COM1)

3.12 Onboard Audio

The onboard audio consists of the Creative Labs ES1373 Chip + AC97.

With a PCI Bus Mastering interface with DOS compatibility, it supports

32 voices wavetable, surround sound, 3D audio, and audio effects such as

reverb and chorus. Creative Labs ES1373 uses single, shareable PCI

interrupt and is PC97 compliant.

Chapter 4 Configuring the Motherboard

TI6VGA User’s Manual 11

Chapter 4 Configuring the Motherboard

The following sections describe the necessary procedures and proper

jumper settings to configure the TI6VGA motherboard. For the locations

of the jumpers, refer to Figure 2.

4.1 CPU Frequency Setting...........................................................13

4.2 Clear CMOS Select: JP6 .........................................................13

4.3 JP2(7-8): SDRAM Clock Select..............................................14

4.4 CPU Host Frequency Force Selector: JP4...............................14

The following examples show the conventions used in this chapter.

Jumper Open

Jumper Closed/Short

Chapter 4 Configuring the Motherboard

12

TI6VGA User’s Manual

Figure 2: Jumper Location on the TI6VGA

Remarks: The TI6VGA comes with 3 DIMM sockets or 2 DIMM

sockets with 64MB SDRAM on board.

Chapter 4 Configuring the Motherboard

TI6VGA User’s Manual 13

4.1 CPU Frequency Setting

The TI6VGA uses jumper-free technology in configuring the processor

on the motherboard. The system automatically detects the CPU bus

speed, 66MHz or 100MHz and sets the multiplier, or ratio, to 3X. The

BIOS (under Chipset Feature Setup) allows users to change the CPU

multiplier (3X, 3.5X, 4X, 4.5X, 5X) to set the correct or desired CPU

frequency.

IMPORTANT NOTE:

It is possible that the system will not

boot if the CPU has been changed. When this happens, turn off

the computer by pressing the power button and turn it on again

by pressing the

Insert

key and the power button

simultaneously. (Note to press the

Insert

key until an image

appears on the screen.) When the system is turned on, press the

Delete

key to enter BIOS Setup and configure the CPU speed.

4.2 Clear CMOS Select: JP6

Use JP6, a 3-pin header, to clear the contents of the CMOS RAM.

Do not clear the CMOS RAM unless it is absolutely necessary. You

will lose your password, etc.

JP6 Jumper Setting Function

1 2 3

pin 1-2: short Normal

1 2 3

pin 2-3: short Clear CMOS

NOTE

:

To clear CMOS, the ATX-power connector should be

disconnected from the motherboard.

Chapter 4 Configuring the Motherboard

14

TI6VGA User’s Manual

4.3 JP2(7-8): SDRAM Clock Select

Use JP2(7-8) to set the SDRAM clock. If the SDRAM on board is

PC-66 compatible (instead of PC-100), while your CPU bus speed

is 100MHz, you have to short JP2(7-8). Failing to do so could lead

to an unstable system.

JP2(7-8) Setting Function

Open Run CPU Clock

Short Run AGP Clock

4.4 CPU Host Frequency Force Selector: JP4

The TI6VGA is able to detect the host frequency (66MHz or 100MHz) of

the installed CPU. The JP4 jumper, however, can be set to

OPEN

to

override the detection and force the host frequency to run at 100MHz.

JP4 Function JP4 Function

SHORT

Host Frequency

Auto-detect

(default)

OPEN

Host Frequency

set to

100MHz

Chapter 5 Installation

TI6VGA User’s Manual 15

Chapter 5 Installation

This chapter describes the interface that the TI6VGA provides for

creating a working system. Refer to Figure 3 for the location of the

connectors.

The following items are covered in this chapter: