EPOX EP-3VCA Manuale utente

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 1.0

December 20, 1999

EP-3VEP-3V

EP-3V

CACA

CA

A SocA Soc

A Soc

kk

k

et 370 Pret 370 Pr

et 370 Pr

ocessor based 4X ocessor based 4X

ocessor based 4X

AA

A

GPGP

GP

mainboard (133/100/66MHz)mainboard (133/100/66MHz)

mainboard (133/100/66MHz)

SupporSuppor

Suppor

ts PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Module

EP-3VCA

User Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language

in any form without the express written permission of EPoX Computer Company

(hereinafter referred to as EPoX) except for documentation kept by the purchaser

for backup purposes.

We provide this manual “as is” without warranty of any kind, either expressed or

implied, including but not limited to the implied warranties or conditions of

merchantability or fitness for a particular purpose. In no event shall EPoX be liable

for any loss of profits, loss of business, loss of use or data, interruption of busi-

ness or for indirect, special incidental, or consequential damages of any kind, even

if EPoX has been advised of the possibility of such damages arising from any

defect or error in the manual or product. EPoX may revise this manual from time

to time without notice. For updated BIOS, drivers, or product release information

you may visit our websites at http://www.epox.com or http://www.epox.com.tw.

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks

or copyrights of their respective companies. The product name and revision

number are both printed on the mainboard itself.

Handling Procedures

Static electricity can severely damage your equipment. Handle the EP-3VCA and

any other device in your system with extreme care and avoid unnecessary contact

with system components on the mainboard. Always work on an antistatic surface to

avoid possible damage to the mainboard from static discharge. Always have the

power supply unplugged and powered off when inserting and removing devices

within the computer chassis. EPoX assumes no responsibility for any damage to

the EP-3VCA mainboard that results from failure to follow instruction or failure to

observe safety precautions.

CAUTION

The EP-3VCA mainboard is subject to

damage by static electricity. Always

observe the handling procedures.

EP-3VCA

Technical Support Services

If you need additional information, help during installation or normal use of this

product, please contact your retailer. Your retailer will have the most current

information about your configuration. If your retailer cannot help, you may visit

our online technical support website and/or contact our support technicians at the

locations listed below.

Record your serial number before installing your EP-3VCA mainboard. (The serial

number is located near the ISA slots at the edge of the board.)

EP-3VCA serial number: ____________________________

Contacting Technical Support

EPoX technical support is working hard to answer all of your questions online.

From our website you can find answers to many common questions, drivers, BIOS

updates, tech notes, and important technical bulletins. If you are still unable to

locate the solution you are seeking, you always have the option to contact our

support technicians directly.

North American website (English language)

http://www.epox.com

[email protected]

European website (Multi-language)

http://www.epox.nl

[email protected]

Taiwan website (Chinese language)

http://www.epox.com.tw

[email protected]

Thank you for using EPoX mainboards!

EP-3VCA

Table of Contents

Section 1 Introduction

Components Checklist ........................................1-1

Overview

EP-3VCA Form-Factor ....................................... 1-2

I/O Shield Connector ..........................................1-3

Power-On/Off (Remote).....................................1-3

System Block Diagram........................................1-4

Section 2 Features

EP-3VCA Features ..............................................2-1

Section 3 Installation

EP-3VCA Detailed Layout..................................3-2

Easy Installation Procedure

CPU Insertion ...................................................... 3-3

Jumper Settings ...................................................3-5

System Memory Configuration .......................... 3-6

Device Connectors .............................................. 3-8

External Modem Ring-in Power ON and

Keyboard Power ON Function (KBPO) ............. 3-10

Section 4 Award BIOS Setup

BIOS Instructions ................................................ 4-1

Standard CMOS Setup .........................................4-2

BIOS Features Setup ........................................... 4-3

Chipset Features Setup........................................4-8

Power Management Setup...................................4-11

PNP/PCI Configuration ...................................... 4-14

Load Setup Defaults ............................................4-16

Integrated Peripherals .........................................4-16

Sensor and CPU Speed Setup..............................4-20

Change Supervisor or User Password.................4-22

IDE HDD Auto Detection ................................... 4-23

Page

EP-3VCA

Save & Exit Setup ................................................ 4-25

Exit Without Saving .............................................4-25

Appendix

Appendix A

Memory Map .......................................................A-1

I/O Map ................................................................A-1

Timer & DMA Channels Map .............................A-2

Interrupt Map ....................................................... A-2

RTC & CMOS RAM Map ....................................A-3

Appendix B

POST Codes.........................................................A-5

Unexpected Errors............................................... A-8

Appendix C

Load Setup Defaults ............................................A-9

Appendix D

GHOST 5.1 Quick User’s Guide.........................A-11

EP-3VCA

Page Left Blank

IntroductionEP-3VCA

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) EP-3VCA mainboard

üü

ü B. (1) EP-3VCA user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) ATA-66 Hard drive ribbon cable

E. (1) PS/2 to AT keyboard connector adapter (optional)

üü

ü F. (1) Driver and utility

A

E

B

USER’S

MANUAL

EP-3VCA

F

or

D

C

Introduction EP-3VCA

Page 1-2

EP-3VCA Form-Factor

The EP-3VCA is designed with ATX form factor - the new industry standard of

chassis. ATX form factor is essentially a Baby-AT baseboard rotated 90 degrees

within the chassis enclosure and a new mounting configuration for the power

supply. With these changes the processor is relocated away from the expansion

slots, allowing them all to hold full length add-in cards. ATX defines a double

height aperture to the rear of the chassis which can be used to host a wide range of

onboard I/O. Only the size and position of this aperture is defined, allowing PC

manufacturers to add new I/O features (e.g.; TV input, TV output, joystick, modem,

LAN, etc.) to systems. This will help systems integrators differentiate their

products in the marketplace, and better meet your needs.

• By integrating more I/O down onto the board and better positioning the hard

drive and floppy connectors material cost of cables and add-in cards is

reduced.

• By reducing the number of cables and components in the system, manufactur-

ing time and inventory holding costs are reduced and reliability will increase.

• By using an optimized power supply, it's possible to reduce cooling costs and

lower acoustical noise. An ATX power supply, which has a side-mounted fan,

allows direct cooling of the processor and add-in cards making a secondary

fan or active heatsink unnecessary in most system applications.

Full length

slots

Expandable I/O

5 1/4"

Bay

3 1/2"

Bay

Figure 2: Summary of ATX chassis features

CPU located near

Power Supply

Single chassis

fan for system

ATX

Power

Supply

ATX power connec-

tor

Floppy / IDE

connectors

close to

peripheral

bays

IntroductionEP-3VCA

Page 1-3

Power-On/Off (Remote)

The EP-3VCA has a single 20-pin connector for ATX power supplies. For ATX

power supplies that support the Remote On/Off feature, this should be connected

to the systems front panel for system Power On/Off button. The systems power

On/Off button should be a momentary button that is normally open.

The EP-3VCA has been designed with “Soft Off" functions. You can turn Off the

system from one of two sources: The first is the front panel Power On/Off

button, and the other is the "Soft Off" function (coming from the EP-3VCA’s

onboard circuit controller) that can be controlled by the operating system.

Windows 95/98 will control this when the user clicks that they are ready to

Shutdown the system.

Figure 4: Simple ATX Power ON/OFF Controller

J 3

ATX

POWER SUPPLY

Case (chassis) Power

ON/OFF button (J 3)

I/O Shield Connector

The EP-3VCA is equipped with an I/O back panel. Please use the appropriate I/O

shield (figure 3).

Figure 3: I/O back panel layout

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Joystick/Midi

Introduction EP-3VCA

Page 1-4

Figure 5: System Block Diagram

System Block Diagram

PAC

PCI Bridge

and memory

controller

VT82C69 4X

133/100 /66MHz

66MHz

Socket 37 0

P rocessor

VT82C686A

I/O Bridge

AC

97

USB 0,1 USB 2,3

AMR Slot

FeaturesEP-3VCA

Page 2-1

Section 2

FEATURES

EP-3VCA Features:

• EP-3VCA is based on the Socket 370 Processors including PCGA & FC-

PGA operating at 300 ~ 700MHz. The board is configured by an ESSJ

(Easy-Setting-Single-Jumper) to match your CPU clock speed.

• Designed with VIA Apollo Pro 133A PCIset.

• Supports up to 768MB of DRAM (minimum of 8 MB) on board (please

see Section 3-2).

• EP-3VCA will support Error Checking and Correcting (ECC) when using

parity SDRAM memory modules. This will detect multiple bit errors and

correct 1-bit memory errors.

• Supports (1) 16 bit ISA slots, (5) 32 bit PCI slots, (1) 4X AGP slot, (1) AMR

slot and provides (2) independent high performance PCI IDE interfaces

capable of supporting PIO Mode 3/4 and Ultra DMA 33/66 devices.

The EP-3VCA supports (5) PCI Bus Master slots and a jumperless PCI

INT# control scheme which reduces configuration confusion when plugging

in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with on chip Multi I/O: (1) floppy port, (1) parallel port (EPP,

ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.epox.com/

please visit our Technical Support section for the latest updates).

Features EP-3VCA

Page 2-2

• EP-3VCA utilizes a Lithium battery which provides environmental

protection and longer battery life.

• Supports the (4) Universal Serial Bus (USB) Ports. The onboard

VT82C686A chip provides the means for connecting PC peripherals such

as; keyboards, joysticks, telephones, and modems.

• Built-in ATX 20-pin power supply connector.

• Software power-down when using Windows

®

95/98.

• Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

• Resume by Alarm - Allows your system to turn on at a preselected time.

• Power Loss Recovery - In the event of a power outtage your system will

automatically turn itself back on without user intervention.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Keyboard power ON function (KBPO).

• Built-in WOL (Wake-up On Lan) Connector.

• Built-in WOM (Wake-up On Modem) Connector.

• Built-in AC97 PCI Audio.

InstallationEP-3VCA

Page 3-1

Section 3

INSTALLATION

EP-3VCA Mainboard

Installation EP-3VCA

Page 3-2

EP-3VCA Detailed Layout

Figure 1

InstallationEP-3VCA

Page 3-3

Easy Installation Procedure

The EP-3VCA is designed for all Socket 370 processors, such as Intel FC-PGA 370

CuMine (Coppermine) 128K/256K processors which are based on 0.18 micro

process technology and utilizing the AGTL+ bus architecture at 100 and 133MHz.

The EP-3VCA has the very few jumpers on board, making your installation faster

and easier. In despite of user friendly design, the EP-3VCA offers the flexible FSB

selection, being capable of running speedy FSB at 133MHz for Intel PIII CuMine

CPU & upcoming new Cyrix Socket 370 processors.

Before you get started, please read the following quick installation guide with

careful.

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. CPU Insertion

3-2. Jumper Settings

3-3. System memory Configuration

3-4. Device Connectors

3-5 External Modem Ring-in Power ON and Keyboard Power ON

Functions (KBPO)

Section 3-1

CPU Insertion

CPU Insertion: (use CuMine

TM

for reference)

Step 1

Open the socket by raising the actuation

lever.

Figure 2

Installation EP-3VCA

Page 3-4

Step 2

Insert the processor.

Ensure proper pin 1 orientation by

aligning the FC-PGA corner marking

with the socket corner closest to the

actuation arm tip. The pin field is keyed

to prevent mis-oriented insertion.

Don’t force processor into socket. If it does

not go in easily, check for mis-orientation

and debris.

Make sure the processor is fully inserted

into the socket on all sides.

Step 3

Close the socket by lowering and

locking the actuation lever.

Note: Intel’s reference design thermal solution is an active heatsink; an extruded alumi-

num heatsink based and a fan attached to the top on the fin array. (See Figure 5)

Figure 3

Figure 4

Figure 5

InstallationEP-3VCA

Page 3-5

1

2

34

ON

1WS)zHM(UPC

1234 oitaRzHM66zHM001zHM331

NONONOX3002003004

NONOX5.3332053764

NONONOX4662004335

NONOX5.4003054006

NONOX5333005766

NOX5.5663055337

NONONOX6004006008*

NONOX5.6334056*768*

NONOX7664007*

NOX5.7005057*

NONOX8335*008*

*reserved

JP1 Clear COMS

1-2 : Normal(default)

2-3 : Clear CMOS

JP4 Keyboard Power-ON Function Selection

1-2 : Disabled(default)

2-3 : Enabled

SW1

Section 3-2

Jumper Settings

SW1: CPU Mutiple Frequency Selection

JP3: CPU FSB Selection

Installation EP-3VCA

Page 3-6

Section 3-3

System Memory Configuration

Memory Layout

The EP-3VCA supports (3) PC133 168-pin DIMMs (Dual In-line Memory

Module). The DIMMs can be either EDO (Enhanced Data Out) or SDRAM

(Synchronized DRAM).

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

125MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 6 and Table 1 show several possible memory configurations using both

SIMM and DIMM.

* SDRAM only supports 8, 16, 32, 64, 128, 256MB DIMM modules.

* We recommend to use PC100 Memory Module for bus speed between 66MHz

and 100MHz and PC133 Memory for bus speed over 100MHz.

* Using non-compliant memory with higher bus speed (over clocking) may

severely compromise the integrity of the system.

DIMM 1

DIMM 2

Bank 0/1

Bank 2/3

DIMM 3

Bank 4/5

-Synchronous

-EDO

yromeMlatoT

1MMID

)1/0knaB(

2MMID

)3/2knaB(

3MMID

)5/4knaB(

BM652=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

enoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

enoN

BM867=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

Figure 6

Table 1

InstallationEP-3VCA

Page 3-7

DIMM Module Installation

Figure 7 displays the notch marks and what they should look like on your DIMM

memory module.

DIMMs have 168-pins and two notches that will match with the onboard DIMM

socket. DIMM modules are installed by placing the chip firmly into the socket at a

90 degree angle and pressing straight down (figure 8) until it fits tightly into the

DIMM socket (figure 9).

Figure 7

Figure 9

DIMM Module clip after installation

To remove the DIMM module simply press down both of the white clips on

either side and the module will be released from the socket.

Figure 8

DIMM Module clip before installation

CENTER KEY ZONE

(3.3 V DRAM)

LEFT KEY ZONE

(UNBUFFERED)

Installation EP-3VCA

Page 3-8

Section 3-4

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your connec-

tions (figure 10).

J2,J3: Chassis Panel Connector

• Power LED, Speaker, Reset, Turbo LED, HDD LED, IR Conn., Sleep/

Power_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL (Wake On Lan) Connector

J8: WOM (Wake On Modem) Connector

IDE1: Primary IDE Connector

IDE2: Secondary IDE Connector

FDD1: Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

CD1: CD Audio Connector

AUX1: AUX Audio Connector

MODEM1: Telephony Connector

• Pin1(Audio_in), Pin2/Pin3(GND), Pin4(Mic-out to Modem)

Figure 10

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Joystic/Midi port

La pagina sta caricando ...

EPOX EP-3VCA Manuale utente

EPOX EP-3VCA Manuale utente

in altre lingue

Documenti correlati

Altri documenti