AEG HD955100NB Manuale utente

USER

MANUAL

EN User Manual 2

Hob

IT Istruzioni per l’uso 29

Piano cottura

HD955100NB

CONTENTS

1. SAFETY INFORMATION.............................................................................................2

2. SAFETY INSTRUCTIONS.............................................................................................5

3. INSTALLATION............................................................................................................ 7

4. PRODUCT DESCRIPTION.........................................................................................12

5. DAILY USE.................................................................................................................. 14

6. HINTS AND TIPS........................................................................................................19

7. CARE AND CLEANING.............................................................................................21

8. TROUBLESHOOTING............................................................................................... 22

9. TECHNICAL DATA.................................................................................................... 25

10. ENERGY EFFICIENCY.............................................................................................27

FOR PERFECT RESULTS

Thank you for choosing this AEG product. We have created it to give you

impeccable performance for many years, with innovative technologies that help

make life simpler – features you might not ﬁnd on ordinary appliances. Please

spend a few minutes reading to get the very best from it.

Visit our website for:

Get usage advice, brochures, trouble shooter, service and repair information:

www.aeg.com/support

Register your product for better service:

www.registeraeg.com

Buy Accessories, Consumables and Original spare parts for your appliance:

www.aeg.com/shop

CUSTOMER CARE AND SERVICE

Always use original spare parts.

When contacting our Authorised Service Centre, ensure that you have the

following data available: Model, PNC, Serial Number.

The information can be found on the rating plate.

Warning / Caution-Safety information

General information and tips

Environmental information

Subject to change without notice.

1.

SAFETY INFORMATION

Before the installation and use of the appliance,

carefully read the supplied instructions. The

manufacturer is not responsible for any injuries or

damages that are the result of incorrect installation or

www.aeg.com

2

usage. Always keep the instructions in a safe and

accessible location for future reference.

1.1 Children and vulnerable people safety

• This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning the use of the appliance in a

safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons

with very extensive and complex disabilities shall be

kept away unless continuously supervised.

• Children of less than 3 years of age should be kept

away unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of

it appropriately.

• Keep children and pets away from the appliance when

it operates or when it cools down. Accessible parts are

hot.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user

maintenance of the appliance without supervision.

1.2

General Safety

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements.

• Do not operate the appliance by means of an external

timer or separate remote-control system.

• WARNING: Unattended cooking on a hob with fat or

oil can be dangerous and may result in ﬁre.

• NEVER try to extinguish a ﬁre with water, but switch off

the appliance and then cover ﬂame e.g. with a lid or a

ﬁre blanket.

ENGLISH

3

• CAUTION: The cooking process has to be supervised.

A short term cooking process has to be supervised

continuously.

• WARNING: Danger of ﬁre: Do not store items on the

cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they

can get hot.

• Do not use a steam cleaner to clean the appliance.

• After use, switch off the hob element by its control

and do not rely on the pan detector.

• If the glass ceramic surface / glass surface is cracked,

switch off the appliance and unplug it from the mains.

In case the appliance is connected to the mains

directly using junction box, remove the fuse to

disconnect the appliance from power supply. In either

case contact the Authorised Service Centre.

• In case of hotplate glass breakage:

– shut immediately off all burners and any electrical

heating element and isolate the appliance from the

power supply,

– do not touch the appliance surface,

– do not use the appliance.

• If the supply cord is damaged, it must be replaced by

the manufacturer, an authorized Service or similarly

qualiﬁed persons in order to avoid a hazard.

• Where the appliance is directly connected to the

power supply, an all-pole isolating switch with a

contact gap is required. Complete disconnection in

compliance with the conditions speciﬁed in

overvoltage category III must be guaranteed. The

earth cable is excluded from this.

• When you route the mains cable, make sure that the

cable doesn't come into direct contact (for example

using insulating sleeving) with parts that can reach

temperatures of more than 50°C above room

temperature.

www.aeg.com

4

• WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by

the manufacturer of the appliance in the instructions

for use as suitable or hob guards incorporated in the

appliance. The use of inappropriate guards can cause

accidents.

2. SAFETY INSTRUCTIONS

This appliance is suitable for the

following markets: IT

2.1 Installation

WARNING!

Only a qualiﬁed person must

install this appliance.

WARNING!

Risk of injury or damage to

the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Keep the minimum distance from

other appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance adjacent

to a door or under a window. This

prevents hot cookware falling from

the appliance when the door or the

window is opened.

• If the appliance is installed above

drawers make sure that the space,

between the bottom of the appliance

and the upper drawer, is

sufﬁcient for

air circulation.

• The bottom of the appliance can get

hot. Make sure to install a non-

combustible separation panel under

the appliance to prevent access to the

bottom.

• Make sure that the ventilation space

of 2 mm, between the worktop and

the front of the below unit, is free. The

warranty does not cover damages

caused by the lack of an adequate

ventilation space.

2.2 Electrical Connection

WARNING!

Risk of ﬁre and electric

shock.

• All electrical connections should be

made by a qualiﬁed electrician.

• The appliance must be earthed.

• Before carrying out any operation

make sure that the appliance is

disconnected from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect

electricity mains cable or plug (if

applicable) can make the terminal

become too hot.

• Use the correct electricity mains

cable.

• Do not let the electricity mains cable

tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the

cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot

appliance or hot cookware, when you

connect the appliance to the near

sockets.

• Do not use multi-plug adapters and

extension cables.

ENGLISH

5

• Make sure not to cause damage to

the mains plug (if applicable) or to the

mains cable. Contact our Authorised

Service Centre or an electrician to

change a damaged mains cable.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have

an isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation

device must have a contact opening

width of minimum 3 mm.

2.3 Gas connection

• All gas connections should be made

by a qualiﬁed person.

• Before installation, make sure that the

local distribution conditions (nature of

the gas and gas pressure) and the

adjustment of the appliance are

compatible.

• Make sure that there is air circulation

around the appliance.

• The information about the gas supply

is on the rating plate.

• This appliance is not connected to a

device, which evacuates the products

of combustion. Make sure to connect

the appliance according to current

installation regulations. Pay attention

to requirements regarding adequate

ventilation.

2.4 Use

WARNING!

Risk of injury, burns and

electric shock.

• Remove all the packaging, labelling

and protective ﬁlm (if applicable)

before ﬁrst use.

• This appliance is for household use

only.

• Do not change the speciﬁcation of

this appliance.

• Make sure that the ventilation

openings are not blocked.

• Do not let the appliance stay

unattended during operation.

• Set the cooking zone to “off” after

each use.

• Do not rely on the pan detector.

• Do not put cutlery or saucepan lids on

the cooking zones. They can become

hot.

• Do not operate the appliance with

wet hands or when it has contact with

water.

• Do not use the appliance as a work

surface or as a storage surface.

• If the surface of the appliance is

cracked, disconnect immediately the

appliance from the power supply. This

to prevent an electrical shock.

• Users with a pacemaker must keep a

distance of minimum 30 cm from the

induction cooking zones when the

appliance is in operation.

• When you place food into hot oil, it

may splash.

WARNING!

Risk of ﬁre and explosion

• Fats and oil when heated can release

ﬂammable vapours. Keep ﬂames or

heated objects away from fats and oils

when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food

remnants, can cause ﬁre at a lower

temperature than oil used for the ﬁrst

time.

• Do not put ﬂammable products or

items that are wet with ﬂammable

products in, near or on the appliance.

WARNING!

Risk of damage to the

appliance.

• Do not keep hot cookware on the

control panel.

www.aeg.com

6

• Do not put a hot pan cover on the

glass surface of the hob.

• Do not let cookware to boil dry.

• Be careful not to let objects or

cookware fall on the appliance. The

surface can be damaged.

• Do not activate the cooking zones

with empty cookware or without

cookware.

• Do not put aluminium foil on the

appliance.

• Cookware made of cast iron,

aluminium or with a damaged bottom

can cause scratches on the glass /

glass ceramic. Always lift these

objects up when you have to move

them on the cooking surface.

• Use only stable cookware with the

correct shape and diameter larger

than the dimensions of the burners.

• Make sure cookware is centrally

positioned on the burners.

• Do not use large cookware that

overlap the edges of the appliance.

This can cause damage to the

worktop surface.

• Use only the accessories supplied

with the appliance.

• Do not install a ﬂame diffuser on the

burner.

• The use of a gas cooking appliance

results in the production of heat and

moisture. Provide good ventilation in

the room where the appliance is

installed.

• Prolonged intensive use of the

appliance may call for additional

ventilation, for example opening of a

window, or more effective ventilation,

for example increasing the level of

mechanical ventilation where present.

• This appliance is for cooking

purposes only. It must not be used for

other purposes, for example room

heating.

• Do not let acid liquids, for example

vinegar, lemon juice or limescale

remover, touch the hob. This can

cause matt patches.

• Discoloration of the enamel or

stainless steel has no effect on the

performance of the appliance.

2.5 Care and cleaning

WARNING!

Do not remove the buttons,

knobs or gaskets from the

control panel. Water may

get inside the appliance and

cause damage.

• Clean the appliance regularly to

prevent the deterioration of the

surface material.

• Deactivate the appliance and let it

cool down before you clean it.

• Disconnect the appliance from the

electrical supply before maintenance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use any abrasive products,

abrasive cleaning pads, solvents or

metal objects.

• Do not clean the burners in the

dishwasher.

2.6 Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

2.7 Disposal

WARNING!

Risk of injury or suffocation.

• Contact your municipal authority for

information on how to discard the

appliance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable

close to the appliance and dispose of

it.

• Flat the external gas pipes.

3.

INSTALLATION

WARNING!

Refer to Safety chapters.

ENGLISH 7

3.1 Before the installation

Before you install the hob, write down

the information bellow from the rating

plate. The rating plate is on the bottom

of the hob.

Model .......................................

PNC .........................................

Serial number ...........................

3.2 Built-in hobs

Only use the built-in hobs after you

assemble the hob into correct built-in

units and work surfaces that align to the

standards.

3.3 Gas Connection

WARNING!

The following instructions

about installation,

maintenance and ventilation

must be carried out by

qualiﬁed personnel in

compliance with the

regulation in force (UNI-CIG

7129 - 7131). Make sure that

the kitchen is well ventilated:

keep natural ventilation

holes open (at least 100 cm²)

or install a mechanical

extractor hood.

Choose ﬁxed connections or use a

ﬂexible pipe in stainless steel in

compliance with the regulation in force. If

you use ﬂexible metallic pipes, be careful

they do not come in touch with mobile

parts or they are not squeezed. Also be

careful when the hob is put together with

an oven.

Make sure that the gas

supply pressure of the

appliance obeys the

recommended values.

If the supplied pressure has not the

speciﬁed value, it is necessary to

assemble a proper pressure regulator in

compliance with the standard UNI EN 88.

For Liquid Gas (LPG) the use of pressure

regulator is allowed only if they are in

compliance with UNI EN 12864. The

adjustable connection is ﬁxed to the

comprehensive ramp by means of a

threaded nut G 1/2". Screw the parts

without force, adjust the connection in

the necessary direction and tighten

everything.

A

B

C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Rigid connection:

Carry out connection by using metal rigid

pipes (copper with mechanical end) (UNI-

CIG 7129).

Flexible connection:

Use a ﬂexible pipe in stainless steel (UNI-

CIG 9891) with a maximum length 2 m.

WARNING!

When installation is

complete, make sure that

the seal of each pipe ﬁtting

is correct. Use a soapy

solution, not a ﬂame!

3.4 Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in

"Technical Information" chapter).

www.aeg.com

8

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can ﬁnd

this plate in the package supplied

with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must ﬁt an applicable pressure

adjuster on the gas supply pipe.

3.5 Adjustment of minimum

level

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob.

4. With a thin screwdriver, adjust the

bypass screw position (A for external

crown and B for internal crown).

A

B

5. If you change:

• from natural gas G20 20 mbar to

liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20

20 mbar, undo the bypass screw

approximately 1/4 of a turn for

internal crown (B) and

approximately 1/3 of a turn for

external crown (A).

WARNING!

Make sure the ﬂame does

not go out when you quickly

turn the knob from the

maximum position to the

minimum position.

3.6 Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• Always use a correctly installed

shockproof socket.

• Make sure that there is an access to

the mains plug after the installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• There is a risk of ﬁre when the

appliance is in connection with an

extension cable, an adapter or a

multiple connection. Make sure that

the ground connection agrees with

the standards and regulations.

• Do not let the power cable to heat up

to a temperature higher than 90° C.

ENGLISH

9

Make sure that you connect

the blue neutral cable to the

terminal with a letter "N" on

it. Connect the brown (or

black) phase cable to the

terminal which has a letter

"L". Keep the phase cable

connected at all times.

To prevent contact between the cable

and the appliance below the hob use the

clamps which are on the side of the

cabinet.

A

A. Rigid copper pipe or ﬂexible pipe of

stainless steel

3.7 Connection cable

• The hob is supplied with the

connection cable.

• Replace the damaged mains cable

only with the spare parts cable. Speak

to your local Authorised Service

Center.

WARNING!

All electrical connections

must be made by a qualiﬁed

electrician.

CAUTION!

Do not drill or solder the

wire ends. This is strictly

forbidden!

CAUTION!

Do not connect the cable

without cable end sleeve.

Use only the special connection cable or

its equivalent. The cable type is:

H05V2V2-F T90.

Make sure that the cable section is

applicable to the voltage and the

working temperature. The yellow / green

earth wire must be approximately 2 cm

longer than the brown (or black) phase

wire.

Two-phase connection

1. Remove the cable end sleeve from

black and brown wires.

2. Remove an insulation of the brown

and black cable ends.

3. Apply a new wire end sleeve of 2.5

mm² on each cable end. (special tool

required).

Cable cross section

N

L

230V~

One-phase connection - 230 V~

Green - yellow

N Blue

L Black and brown

3.8 Attaching the seal - On-top

installation

1. Clean the worktop around the cut

out area.

2. Attach the supplied thinner seal

stripe to the lower edge of the hob

along the outer edge of the glass

ceramic. Do not extend it. Make sure

that the ends of the seal stripe are

located in the middle of one side of

the hob.

3. Add some mm when you cut the seal

stripe to the length.

4. Push the two ends of seal stripe

together.

www.aeg.com

10

3.9 Assembly

min.

450mm

min.

650mm

min.

2mm

min. 2 mm

A

B

min.20 mm

(max.150 mm)

A

12 mm

28 mm

38 mm

B

57 mm

41 mm

31 mm

min. 500 mm

min. 60 mm

D

C

C. Removable panel

D. Space for connections

R 5 mm

min.

55 mm

490

mm

830

mm

600 mm

min.

38 mm

min.

2 mm

CAUTION!

Install the appliance only on

a worktop with a ﬂat surface.

3.10 Possibilities for insertion

Kitchen unit with oven

The electrical connection of the hob and

the oven must be installed separately for

ENGLISH

11

safety reasons and to let easy remove

oven from the unit.

If you install the hob

asymmetrically rightward the

minimum distance between

left edge of the hob and left

support must be 72 mm.

min.

72 mm

CAUTION!

The bottom of the appliance

can get hot. If an oven isn't

installed beneath the hob, a

non-combustible separation

panel must be installed

under the appliance to

prevent access to the

bottom. The position of the

panel is described in the

"Installation" chapter.

4. PRODUCT DESCRIPTION

4.1 Cooking surface layout

145 mm

180 mm

210 mm

4 3

21

1

Dual burner

2

Induction cooking zones

3

Control panel

4

Control knob

4.2 Control knob

Symbol Description

no gas supply / off posi-

tion

ignition position / maxi-

mum gas supply

Symbol Description

minimum gas supply

internal crown

double crown

www.aeg.com12

4.3 Control panel layout

1 2 3

5

64

8 710

9

Use the sensor ﬁelds to operate the appliance. The displays, indicators and sounds tell

which functions operate.

Sensor

ﬁeld

Function Comment

1

ON / OFF To activate and deactivate the hob.

2

Lock / Child Safety De-

vice

To lock / unlock the control panel.

3

STOP+GO To activate and deactivate the function.

4

- Heat setting display To show the heat setting.

5

- Timer indicators of cook-

ing zones

To show for which zone you set the time.

6

- Timer display To show the time in minutes.

7

- To select the cooking zone.

8

/

- To increase or decrease the time.

9

PowerBoost To activate and deactivate the function.

10

- Control bar To set a heat setting.

4.4 Heat setting displays

Display Description

The cooking zone is deactivated.

-

The cooking zone operates.

STOP+GO operates.

Automatic Heat Up operates.

ENGLISH 13

Display Description

PowerBoost operates.

+ digit

There is a malfunction.

/ /

OptiHeat Control (3 step Residual heat indicator): continue cooking /

keep warm / residual heat.

Lock / Child Safety Device operates.

Incorrect or too small cookware or no cookware on the cooking zone.

Automatic Switch Off operates.

4.5 OptiHeat Control (3 step

Residual heat indicator)

WARNING!

/ / There is a risk of

burns from residual heat.

The indicators show the level

of the residual heat for the

cooking zones you are

currently using. The

indicators may also come on

for the neighbouring

cooking zones even if you

are not using them.

The induction cooking zones produce

the heat necessary for the cooking

process directly in the bottom of the

cookware. The glass ceramic is heated by

the heat of the cookware.

5. DAILY USE

WARNING!

Refer to Safety chapters.

5.1 Gas burners

Burner overview

A

B

C

D

A. Burner cap

B. Burner crown

C. Ignition candle

D. Thermocouple

Ignition of the burner

Always light the burner

before you put on the

cookware.

WARNING!

Be very careful when you use

open ﬁre in the kitchen

environment. The

manufacturer declines any

responsibility in case of the

ﬂame misuse.

1. Push the control knob down and turn

it counterclockwise to the maximum

gas supply position (

). The ﬂame

will switch on in the two burner

www.aeg.com

14

crowns of Dual burner. To light the

internal crown of the Dual burner

push down the control knob and turn

it clockwise to the maximum position

( ).

2. Keep the control knob pushed for

equal or less than 10 seconds. This

lets the thermocouple warm up. If

not, the gas supply is interrupted.

3. Adjust the ﬂame after it is regular.

If after some tries the burner

does not light, check if the

crown and its cap are in

correct positions.

WARNING!

Do not keep the control

knob pushed for more than

15 seconds. If the burner

does not light after 15

seconds, release the control

knob, turn it into off position

and try to light the burner

again after minimum 1

minute.

CAUTION!

In the absence of electricity

you can ignite the burner

without electrical device; in

this case approach the

burner with a ﬂame, turn the

control knob counter-

clockwise to maximum gas

supply position and push it

down. Keep the control

knob pushed for equal or

less than 10 seconds to let

the thermocouple warm up.

If the burner accidentally

goes out, turn the control

knob to the off position and

try to light the burner again

after minimum 1 minute.

The spark generator can

start automatically when you

switch on the mains, after

installation or a power cut. It

is normal.

Turning the burner off

To put the ﬂame out, turn the knob to

the off position .

WARNING!

Always turn the ﬂame down

or switch it off before you

remove the pans from the

burner.

Using the wok stand

The wok stand lets you use a round

bottomed wok on the hob. Use the wok

stand on the Dual burner only. When you

reﬁt the wok stand, make sure the

recesses on the frame ﬁt securely to the

bars of the pan supports.

The shape of pan supports can be

different in other models of the

appliance.

When you

reﬁt the grate of

the Dual burner, make sure

to match the hollow part of

the grate with the reference

located on the plate ﬁxed to

the glass.

5.2 Induction cooking zones

Activating and deactivating

Touch for 1 second to activate or

deactivate the hob.

Automatic Switch Off

The function deactivates the hob

automatically if:

• all cooking zones are deactivated,

• you do not set the heat setting after

you activate the hob,

• you spill something or put something

on the control panel for more than 10

seconds (a pan, a cloth, etc.). An

ENGLISH

15

acoustic signal sounds and the hob

deactivates. Remove the object or

clean the control panel.

• the hob gets too hot (e.g. when a

saucepan boils dry). Let the cooking

zone cool down before you use the

hob again.

• you use incorrect cookware. The

symbol comes on and the cooking

zone deactivates automatically after 2

minutes.

• you do not deactivate a cooking zone

or change the heat setting. After

some time comes on and the hob

deactivates.

The relation between the heat setting

and the time after which the hob

deactivates:

Heat setting The hob deacti-

vates after

, 1 - 3

6 hours

4 - 7 5 hours

8 - 9 4 hours

10 - 14 1.5 hour

The heat setting

To set or change the heat setting:

Touch the control bar at the correct heat

setting or move your

ﬁnger along the

control bar until you reach the correct

heat setting.

Automatic Heat Up

Activate this function to get a desired

heat setting in a shorter time. When it is

on, the zone operates on the highest

setting in the beginning and then

continues to cook at the desired heating

setting.

To activate the function the

cooking zone must be cold.

To activate the function for a cooking

zone: touch ( comes on).

Immediately touch a desired heat

setting. After 3 seconds

comes on.

To deactivate the function: change the

heat setting.

PowerBoost

This function makes more power

available to the induction cooking zones.

The function can be activated for the

induction cooking zone only for a limited

period of time. After this time the

induction cooking zone automatically

sets back to the highest heat setting.

To activate the function for a cooking

zone: touch

. comes on.

To deactivate the function: change the

heat setting.

Timer

Count Down Timer

You can use this function to set how long

the cooking zone should operate for a

single cooking session.

First set the heat setting for the cooking

zone then set the function.

To set the cooking zone: touch

again and again until the indicator of a

necessary cooking zone comes on.

To activate the function: touch of

the timer to set the time (00 - 99

minutes). When the indicator of the

cooking zone starts to ﬂash slowly the

time counts down.

To see the remaining time: set the

cooking zone with . The indicator of

the cooking zone starts to ﬂash quickly.

The display shows the remaining time.

To change the time: set the cooking

zone with . Touch or .

To deactivate the function: set the

cooking zone with and touch . The

www.aeg.com

16

remaining time counts back to 00. The

indicator of the cooking zone goes out.

When the time comes to an

end, the sound operates and

00 ﬂashes. The cooking zone

deactivates.

To stop the sound: touch .

CountUp Timer (The count up timer)

You can use this function to monitor how

long the cooking zone operates.

To set the cooking zone: touch

again and again until the indicator of a

necessary cooking zone comes on.

To activate the function: touch of

the timer. comes on. When the

indicator of the cooking zone starts to

ﬂash slowly the time counts up. The

display switches between and

counted time (minutes).

To see how long the cooking zone

operates: set the cooking zone with

.

The indicator of the cooking zone starts

to

ﬂash quickly. The display shows how

long the zone operates.

To deactivate the function: set the

cooking zone with and touch or

. The indicator of the cooking zone

goes out.

Minute Minder

You can use this function as a Minute

Minder when the hob is activated and

the cooking zones do not operate. The

heat setting display shows .

To activate the function: touch

.

Touch or of the timer to set the

time. When the time comes to an end,

the sound operates and 00 ﬂashes.

To stop the sound: touch .

The function has no effect

on the operation of the

cooking zones.

STOP+GO

This function sets all cooking zones that

operate to the lowest heat setting.

When the function operates, you cannot

change the heat setting.

To activate the function: touch

.

comes on.

To deactivate the function: touch .

The previous heat setting comes on.

Lock

You can lock the control panel while

cooking zones operate. It prevents an

accidental change of the heat setting.

Set the heat setting ﬁrst.

To activate the function: touch .

comes on for 4 seconds.

To deactivate the function: touch .

The previous heat setting comes on.

When you deactivate the

hob, you also deactivate this

function.

Child Safety Device

This function prevents an accidental

operation of the hob.

To activate the function: activate the

hob with . Do not set the heat setting.

Touch

for 4 seconds. comes on.

Deactivate the hob with .

To deactivate the function: activate the

hob with . Do not set the heat setting.

Touch

for 4 seconds. comes on.

Deactivate the hob with .

To override the function for only one

cooking time: activate the hob with .

comes on. Touch for 4 seconds.

Set the heat setting in 10 seconds. You

can operate the hob. When you

deactivate the hob with the function

operates again.

ENGLISH

17

OffSound Control

(Deactivating and activating

the sounds)

Deactivate the hob. Touch for 3

seconds. The display comes on and goes

out. Touch for 3 seconds. or

comes on. Touch of the timer to

choose one of the following:

• - the sounds are off

• - the sounds are on

To conﬁrm your selection wait until the

hob deactivates automatically.

When the function is set to you can

hear the sounds only when:

• you touch

• Minute Minder comes down

• Count Down Timer comes down

• you put something on the control

panel.

Power limitation

Originally the hob is at its highest

possible power level.

To decrease or increase the power

level:

1. Deactivate the hob.

2. Touch

for 3 seconds. The display

comes on and goes off.

3. Touch for 3 seconds. or

comes on.

4. Touch

. P0 comes on.

5. Touch / of the Timer to set the

power level.

6. Wait for the display to go off.

Power levels

Refer to “Technical data” chapter.

• P0 — 7200 W

• P1 — 1500 W

• P2 — 2000 W

• P3 — 2500 W

• P4 — 3000 W

• P5 — 3500 W

• P6 — 4000 W

• P7 — 4500 W

• P8 — 5000 W

• P9 — 6000 W

CAUTION!

Make sure that the selected

power ﬁts to the house

installation fuses.

Power management function

• Cooking zones are grouped

according to the location and number

of the phases in the hob. See the

illustration.

• Each phase has a maximum electricity

loading of 3700 W.

• The function divides the power

between cooking zones connected to

the same phase.

• The function activates when the total

electricity loading of the cooking

zones connected to a single phase

exceeds 3700 W.

• The function decreases the power to

the other cooking zones connected to

the same phase.

• The heat setting display of the

reduced zones alternates between the

chosen heat setting and the reduced

heat setting. After some time the heat

setting display of the reduced zones

stays on the reduced heat setting.

Power management function with

Power limitation function

When you set the Power limitation

function to 4.5 kW or less, power of the

hob is divided between all cooking

zones.

When you set the Power limitation

function to more than 4.5 kW, the

power of the hob is divided between its

left and right side.

www.aeg.com

18

6. HINTS AND TIPS

WARNING!

Refer to Safety chapters.

6.1 Cookware

Electric:

For induction cooking zones

a strong electro-magnetic

ﬁeld creates the heat in the

cookware very quickly.

Use the induction cooking

zones with suitable

cookware.

Cookware material

• correct: cast iron, steel, enamelled

steel, stainless steel, multi-layer

bottom (with a correct marking from a

manufacturer).

• not correct: aluminium, copper,

brass, glass, ceramic, porcelain.

Cookware is suitable for an induction

hob if:

• water boils very quickly on a zone set

to the highest heat setting.

• a magnet pulls on to the bottom of

the cookware.

The bottom of the cookware

must be as thick and ﬂat as

possible.

Ensure pan bases are clean

and dry before placing on

the hob surface.

Cookware dimensions

Induction cooking zones adapt to the

dimension of the bottom of the

cookware automatically.

The cooking zone efﬁciency is related to

the diameter of the cookware. The

cookware with a diameter smaller than

the minimum receives only a part of the

power generated by the cooking zone.

Refer to "Technical data".

CAUTION!

Do not use cast iron pans,

clay or earthenware pots,

grill or toaster plates.

Gas:

WARNING!

Do not put the same pan on

two burners.

WARNING!

Do not put unstable or

damaged pots on the burner

to prevent spills and injuries.

CAUTION!

Make sure that pot handles

are not above the front edge

of the cooktop.

CAUTION!

Make sure that the pots are

placed centrally on the

burner in order to get the

maximum stability and a

lower gas consumption.

ENGLISH 19

CAUTION!

Liquids spilt during cooking

can cause the glass to break.

6.2 Diameters of cookware

Use cookware with

diameters applicable to the

size of burners.

Burner Diameter of

cookware (mm)

Dual 220 - 300

6.3 Öko Timer (Eco Timer)

To save energy, the heater of the cooking

zone deactivates before the count down

timer sounds. The difference in the

operation time depends on the heat

setting level and the length of the

cooking operation.

6.4 The noises during

operation (for induction

cooking zones)

If you can hear:

• crack noise: cookware is made of

different materials (sandwich

construction).

• whistle sound: you the cooking zone

with high power level and the

cookware is made of different

materials (sandwich construction).

• humming: you use high power level.

• clicking: electric switching occurs.

• hissing, buzzing: the fan operates.

The noises are normal and do not refer

to hob malfunction.

6.5 Examples of cooking

applications (for induction

cooking zones)

The relation between the heat setting

and the cooking zone consumption of

power is not linear. When you increase

the heat setting, it is not proportional to

the increase of the cooking zone

consumption of power. It means that the

cooking zone with the medium heat

setting uses less than a half of its power.

The data in the table is for

guidance only.

Heat setting Use to: Time

(min)

Hints

- 1

Keep cooked food warm. as nec-

essary

Put a lid on the cookware.

1 - 3 Hollandaise sauce, melt: but-

ter, chocolate, gelatine.

5 - 25 Mix from time to time.

1 - 3 Solidify: ﬂuffy omelettes,

baked eggs.

10 - 40 Cook with a lid on.

3 - 5 Simmer rice and milkbased

dishes, heating up ready-

cooked meals.

25 - 50 Add the minimum twice as

much liquid as rice, mix milk

dishes part procedure

through.

5 - 7 Steam vegetables, ﬁsh, meat. 20 - 45 Add some tablespoons of liq-

uid.

7 - 9 Steam potatoes. 20 - 60 Use max. ¼ l water for 750 g of

potatoes.

www.aeg.com20

La pagina sta caricando ...

AEG HD955100NB Manuale utente

AEG HD955100NB Manuale utente

in altre lingue

Documenti correlati

Altri documenti