Gigabyte B550 VISION D-P Manuale del proprietario

Marca: Gigabyte

Modello: B550 VISION D-P

Categoria: Schede madri

Tipo: Manuale del proprietario

To reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

For more product details, please visit GIGABYTE's website.

B550 VISION D-P

User's Manual

Rev. 1001

12ME-B55VSDP-1001R

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of

documentations:

For quick set-up of the product, read the Quick Installation Guide included with the product.

For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before updating

motherboard BIOS, drivers, or when looking for technical information.

Example:

- 3 -

Table of Contents

B550 VISION D-P Motherboard Layout ........................................................................... 4

Chapter 1 Hardware Installation .....................................................................................5

1-1 Installation Precautions .................................................................................... 5

1-2 ProductSpecications ...................................................................................... 6

1-3 Installing the CPU .......................................................................................... 10

1-4 Installing the Memory ..................................................................................... 10

1-5 Installing an Expansion Card ......................................................................... 11

1-6 Back Panel Connectors .................................................................................. 11

1-7 Internal Connectors ........................................................................................ 14

Chapter 2 BIOS Setup ..................................................................................................24

2-1 Startup Screen ............................................................................................... 24

2-2 The Main Menu .............................................................................................. 25

2-3 Favorites (F11) ............................................................................................... 26

2-4 Tweaker .......................................................................................................... 27

2-5 Settings .......................................................................................................... 30

2-6 System Info. ................................................................................................... 36

2-7 Boot ................................................................................................................ 37

2-8 Save & Exit ..................................................................................................... 40

Chapter 3 Appendix ......................................................................................................41

3-1 ConguringaRAIDSet .................................................................................. 41

3-2 Drivers Installation .......................................................................................... 43

3-3 Debug LED Codes ......................................................................................... 44

RegulatoryNotices .................................................................................................... 48

Contact Us ................................................................................................................ 52

- 4 -

B550 VISION D-P Motherboard Layout

Box Contents

5B550 VISION D-P motherboard 5One antenna

5Motherboard driver disc 5Four SATA cables

5User's Manual 5Two thermistor cables

5Quick Installation Guide 5One G Connector

5OneRGBLEDstripextensioncable

* The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

CPU DRAM

VGA BOOT

USB 2.0 Hub (Note 2)

KB_MS_USB

DP_HDMI

U32_LAN

TYPEC_1

U32_2

TYPEC_2

QFLED QFLASH_PLUS

U32G2_LAN

ATX

DB_PORT (Note 1)

AUDIO

DDR4_A1

DDR4_A2

DDR4_B1

DDR4_B2

ATX_12V

AMD B550

CLR_CMOS

M_BIOS

PCIEX8

PCIEX4

PCIEX16

SYS_FAN5_PUMPSYS_FAN4

SYS_FAN2

EC_TEMP1

F_U32C

CODEC

B550 VISION D-P

F_PANEL

F_USB1

SATA_DOM0

EC_TEMP2 SYS_FAN6_PUMP

F_USB2SYS_FAN3

USB 2.0 Hub

D_LED2

D_LED1

LED_C2

LED_C1

F_AUDIO

F_U32

SYS_FAN1

LED_CPU

M2_WIFI

COM

CPU_OPT

iTE®

Super I/O

M2A_CPU

426080110

M2B_SB

426080110

SATA3

0 1

BAT

Intel® 2.5GbE LAN

Intel® Thunderbolt™ 3

Controller

Realtek® 2.5GbE LAN

TPM

Socket AM4

CPU_FAN

(Note 1) For debug code information, please refer to Chapter 3.

(Note 2) The chip is located on the back of the motherboard.

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature or wet environment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 5 -

1-2 ProductSpecications

- 6 -

CPU AMD Socket AM4, support for:

3rdGenerationAMDRyzen™ processors/

3rdGenerationAMDRyzen™withRadeon™ Graphics processors

(Go to GIGABYTE's website for the latest CPU support list.)

Chipset AMD B550

Memory 4xDDR4DIMMsocketssupportingupto128GB(32GBsingleDIMMcapacity)

of system memory

SupportforDDR43200/2933/2667/2400/2133MHzmemorymodules

Dual channel memory architecture

SupportforECCUn-bufferedDIMM1Rx8/2Rx8memorymodules

Supportfornon-ECCUn-bufferedDIMM1Rx8/2Rx8/1Rx16memorymodules

SupportforExtremeMemoryProle(XMP)memorymodules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integratedinthe3rdGenerationAMDRyzen™withRadeon™ Graphics processors+

Intel® Thunderbolt™ 3 Controller:

- 2 x Intel® Thunderbolt™ 3 connectors (USB Type-C™ ports), supporting

DisplayPort and Thunderbolt™ video outputs and a maximum resolution of

5120x2880@60Hzwith24bpp

* Because of the limited I/O resources of the PC architecture, the number of

Thunderbolt™ devices that can be used is dependent on the number of the PCI

Expressdevicesbeinginstalled.(RefertoChapter1-6,"BackPanelConnectors,"

for more information.)

* SupportforDisplayPort1.4version,HDCP2.3,andHDR.

Integratedinthe3rdGenerationAMDRyzen™withRadeon™ Graphics processors:

- 1xHDMIport,supportingamaximumresolutionof4096x2160@60Hz

* SupportforHDMI2.1version,HDCP2.3,andHDR.

Maximum shared memory of 16 GB

Audio Realtek® ALC1220-VB codec

* The back panel line out jack supports DSD audio.

Support for DTS:X® Ultra

HighDenitionAudio

2/4/5.1/7.1-channel

Support for S/PDIF Out

LAN Intel® 2.5GbE LAN chip (2.5 Gbit/1000 Mbit/100 Mbit) (LAN1)

Realtek® 2.5GbE LAN chip (2.5 Gbit/1000 Mbit/100 Mbit) (LAN2)

Wireless

Communication

Module

Intel® Wi-Fi 6 AX200

- WIFIa,b,g,n,acwithwave2features,ax,supporting2.4/5GHzDual-Band

- BLUETOOTH 5

- Supportfor11ax160MHzwirelessstandardandupto2.4Gbpsdatarate

* Actual data rate may vary depending on environment and equipment.

Expansion Slots 1 x PCI Express x16 slot (PCIEX16), integrated in the CPU:

- 3rdGenerationAMDRyzen™ processors support PCIe 4.0 x16 mode

- 3rdGenerationAMDRyzen™withRadeon™ Graphics processors support

PCIe 3.0 x16 mode

* For optimum performance, if only one PCI Express graphics card is to be installed,

be sure to install it in the PCIEX16 slot.

1 x PCI Express x16 slot (PCIEX8), integrated in the CPU:

- 3rdGenerationAMDRyzen™ processors support PCIe 4.0 x8 mode

- 3rdGenerationAMDRyzen™withRadeon™ Graphics processors support

PCIe 3.0 x8 mode

* The PCIEX8 slot shares bandwidth with the PCIEX16 slot. When the PCIEX8 slot is

populated, the PCIEX16 slot operates at up to x8 mode.

1 x PCI Express x16 slot (PCIEX4), integrated in the Chipset:

- Supporting PCIe 3.0 x4 mode

* The PCIEX4 slot shares bandwidth with the M2B_SB connector. The PCIEX4 slot

becomes unavailable when a device is installed in the M2B_SB connector.

Multi-Graphics

Technology Support for AMD Quad-GPU CrossFire™ and 2-Way AMD CrossFire™ technologies

Storage Interface  1 x M.2 connector (M2A_CPU), integrated in the CPU, supporting Socket 3,

M key, type 2242/2260/2280/22110 SSDs:

- 3rdGenerationAMDRyzen™ processors support SATA and PCIe 4.0 x4/x2

SSDs

- 3rdGenerationAMDRyzen™withRadeon™ Graphics processors support

SATA and PCIe 3.0 x4/x2 SSDs

 1 x M.2 connector (M2B_SB), integrated in the Chipset, supporting Socket 3,

M key, type 2242/2260/2280/22110 SSDs:

- Supporting SATA and PCIe 3.0 x4/x2 SSDs

4 x SATA 6Gb/s connectors, integrated in the Chipset:

- SupportforRAID0,RAID1,andRAID10

USB Integrated in the CPU:

- 3 x USB 3.2 Gen 1 ports on the back panel

- 1 x USB 3.2 Gen 2 Type-A port (red) on the back panel

Chipset+Intel® Thunderbolt™ 3 Controller:

- 2 x USB Type-C™ ports on the back panel, with USB 3.2 Gen 2 support

Chipset:

- 1 x USB Type-C™ port with USB 3.2 Gen 1 support, available through the

internal USB header

- 1 x USB 3.2 Gen 2 Type-A port (red) on the back panel

- 2 x USB 3.2 Gen 1 ports available through the internal USB header

- 1 x USB 2.0/1.1 port on the back panel

Chipset+2 USB 2.0 Hubs:

- 5 x USB 2.0/1.1 ports (1 port on the back panel, 4 ports available through

the internal USB headers)

- 7 -

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 8-pin ATX 12V power connector

1 x CPU fan header

1 x water cooling CPU fan header

4 x system fan headers

2 x system fan/water cooling pump headers

2 x addressable LED strip headers

2xRGBLEDstripheaders

1xCPUcoolerLEDstrip/RGBLEDstripheader

2 x M.2 Socket 3 connectors

4 x SATA 6Gb/s connectors

1 x SATA DOM power connector

1 x front panel header

1 x front panel audio header

1 x USB Type-C™ port, with USB 3.2 Gen 1 support

1 x USB 3.2 Gen 1 header

2 x USB 2.0/1.1 headers

 1 x Trusted Platform Module (TPM) header (2x6 pin, for the GC-TPM2.0_S

module only)

1 x serial port header

1 x Clear CMOS jumper

2 x temperature sensor headers

1 x Q-Flash Plus button

Back Panel

Connectors

1 x PS/2 keyboard/mouse port

1 x DisplayPort In port

1 x HDMI port

2xSMAantennaconnectors(2T2R)

2 x USB 3.2 Gen 2 Type-A ports (red)

2 x Thunderbolt™ 3 connectors (USB Type-C™ port, with USB 3.2 Gen 2 support)

3 x USB 3.2 Gen 1 ports

2 x USB 2.0/1.1 ports

2xRJ-45ports

1 x optical S/PDIF Out connector

5 x audio jacks

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Watercoolingowratedetection

Overheating warning

Fan fail warning

Fan speed control

* Whether the fan (pump) speed control function is supported will depend on the fan

(pump) you install.

- 8 -

BIOS 1x256Mbitash

Use of licensed AMI UEFI BIOS

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functionsofeachapplicationmayalsovarydependingonmotherboardspecications.

- @BIOS

- EasyTune

- Fast Boot

- Game Boost

- ON/OFF Charge

- RGBFusion

- Smart Backup

- System Information Viewer

Support for Q-Flash Plus

Support for Q-Flash

Support for Xpress Install

Bundled

Software

Norton® Internet Security (OEM version)

cFosSpeed

Operating

System Support for Windows 10 64-bit

Form Factor ATX Form Factor; 30.5cm x 24.4cm

* GIGABYTEreservestherighttomakeanychangestotheproductspecicationsandproduct-relatedinformationwithout

prior notice.

Please visit GIGABYTE's website

for support lists of CPU, memory

modules, SSDs, and M.2 devices.

Please visit the Support\Utility List

page on GIGABYTE's website to

download the latest version of apps.

-9-

1-3 Installing the CPU

Please visit GIGABYTE's website for details on hardware installation.

DualChannelMemoryConguration

This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.EnablingDual

Channel memory mode will double the original memory bandwidth.

The four memory sockets are divided into two channels and each channel has two memory sockets as following:

ChannelA:DDR4_A1,DDR4_A2

ChannelB:DDR4_B1,DDR4_B2

ReadthefollowingguidelinesbeforeyoubegintoinstalltheCPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly.

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur.

•SettheCPUhostfrequencyinaccordancewiththeCPUspecications.Itisnotrecommended

thatthesystembusfrequencybesetbeyondhardwarespecicationssinceitdoesnotmeetthe

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications,pleasedosoaccordingtoyourhardwarespecicationsincludingtheCPU,graphics

card, memory, hard drive, etc.

Installing the CPU

Completely lift up the CPU socket locking lever. Locate the pin one (denoted by a small triangle) of the CPU

socketandtheCPU.OncetheCPUispositionedintoitssocket,placeonengerdownonthemiddleofthe

CPU, lowering the locking lever and latching it into the fully locked position.

AM4 Socket

A Small Triangle

Marking Denotes Pin

One of the Socket AM4 CPU

A Small Triangle

Marking Denotes CPU

Pin One

1-4 Installing the Memory

Readthefollowingguidelinesbeforeyoubegintoinstallthememory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

- 10 -

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one memory module is installed.

2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory

of the same capacity, brand, speed, and chips be used.

1-5 Installing an Expansion Card

Readthefollowingguidelinesbeforeyoubegintoinstallanexpansioncard:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

RecommandedDualChannelMemoryConguration:

DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

2 Modules - - DS/SS - - DS/SS

4 Modules DS/SS DS/SS DS/SS DS/SS

(SS=Single-Sided,DS=Double-Sided,"--"=NoMemory)

1-6 Back Panel Connectors

USB 2.0/1.1 Port

TheUSBportsupportstheUSB2.0/1.1specication.UsethisportforUSBdevices.

USB 2.0/1.1 Port (Q-Flash Plus Port)

TheUSBportsupportstheUSB2.0/1.1specication.UsethisportforUSBdevices.BeforeusingQ-Flash

Plus (Note 1),makesuretoinserttheUSBashdriveintothisportrst.

PS/2 Keyboard and PS/2 Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

DisplayPort In port

TheDisplayPortInportoffersvideooutputstothemotherboard.RefertotheThunderbolt™ 3 Connector

for more information.

HDMI Port (Note 2)

The HDMI port is HDCP 2.3 compliant and supports Dolby TrueHD and DTS

HDMasterAudioformats. Italsosupportsupto192KHz/24bit7.1-channel

LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum

supportedresolutionis4096x2160@60Hz,buttheactualresolutionssupportedaredependentonthe

monitor being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The

item name may differ depending on your operating system.)

•Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

- 11 -

(Note1) ToenabletheQ-FlashPlusfunctionpleasevisitthe "UniqueFeatures"webpageof GIGABYTE's

website.

(Note2) For3rdGenerationAMDRyzen™withRadeon™ Graphics processors only.

SMA Antenna Connectors (2T2R)

Use this connector to connect an antenna.

Tighten the antennas to the antenna connectors and then aim the antennas correctly for better

signal reception.

Activity LED

Connection/

Speed LED

LAN Port

Connection/Speed LED:

State Description

Green 2.5 Gbps data rate

Orange 1 Gbps data rate

Off 100 Mbps data rate

Activity LED:

State Description

Blinking Data transmission or receiving is occurring

On No data transmission or receiving is occurring

USB 3.2 Gen 1 Port

TheUSB3.2Gen1portsupportstheUSB3.2Gen1specicationandiscompatibletotheUSB2.0

specication.UsethisportforUSBdevices.

Thunderbolt™ 3 Connector (USB Type-C™ Port, with USB 3.2 Gen 2 support)

The connector supports standard DisplayPort and Thunderbolt™ video outputs. You can connect a standard

DisplayPort/Thunderbolt™ monitor to this connector with an adapter. The Thunderbolt™ connector can daisy

chain up to six Thunderbolt™ devices. Because of the limited I/O resources of the PC architecture, the

number of Thunderbolt™ devices that can be used is dependent on the number of the PCI Express devices

being installed. You can adjust the Thunderbolt™settingsunderSettings\ThunderboltCongurationinBIOS

Setup.Themaximumsupportedresolutionis5120x2880@60Hzwith24bppwhenusingaDisplayPort

monitor, but the actual resolutions supported are dependent on the monitor being used. Also, the connector

isreversibleandsupportstheUSB3.2Gen2specicationandiscompatibletotheUSB3.2Gen1and

USB2.0specication.YoucanusethisportforUSBdevices,too.

RJ-45 LAN Port (LAN1)

The Gigabit Ethernet LAN port provides Internet connection at up to 2.5 Gbps data rate. The following

describes the states of the LAN port LEDs.

Follow the steps below to install the DisplayPort or Thunderbolt™ devices:

Step 1:

Connect your DisplayPort cable or Mini-DisplayPort

cable (purchased separately) from the graphics

card to the DisplayPort In port on the back panel.

Step 2:

Then connect the DisplayPort or Thunderbolt™

devices to Thunderbolt™ 3 connector to complete.

- 12 -

PleasevisitGIGABYTE'swebsitefordetailsonconguringtheaudiosoftware.

•If you want to install a Side Speaker, you need to retask either the Line in or Mic in jack to be

Side Speaker out through the audio driver.

•ToenableorconguretheaudioamplifyingfunctionfortheLineoutjack,pleaseaccessthe

HD Audio Manager application.

AudioJackCongurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

Center/Subwoofer Speaker Out a a

RearSpeakerOut a a a

Line In/Side Speaker Out a

Line Out/Front Speaker Out a a a a

Mic In/Side Speaker Out a

USB 3.2 Gen 2 Type-A Port (Red)

TheUSB3.2Gen2portsupportstheUSB3.2Gen2specicationandiscompatibletotheUSB3.2Gen1

andUSB2.0specication.UsethisportforUSBdevices.

Center/Subwoofer Speaker Out

Use this audio jack to connect center/subwoofer speakers.

Rear Speaker Out

Use this audio jack to connect rear speakers.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio.

Before using this feature, ensure that your audio system provides an optical digital audio in connector.

Line In/Side Speaker Out

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out

The line out jack. This jack supports audio amplifying function. For better sound quality, it is recommended

that you connect your headphone/speaker to this jack (actual effects may vary by the device being used).

Mic In/Side Speaker Out

The Mic in jack.

RJ-45 LAN Port (LAN2)

The Gigabit Ethernet LAN port provides Internet connection at up to 2.5 Gbps data rate. The following

describes the states of the LAN port LEDs.

Activity LED

Connection/

Speed LED

LAN Port

Connection/Speed LED:

State Description

Orange 2.5 Gbps data rate

Green 1 Gbps data rate

Off 100 Mbps data rate

Activity LED:

State Description

Blinking Data transmission or receiving is occurring

Off No data transmission or receiving is occurring

- 13 -

1-7 Internal Connectors

Readthefollowingguidelinesbeforeconnectingexternaldevices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN1/2/3/4

5) SYS_FAN5_PUMP/SYS_FAN6_PUMP

6) CPU_OPT

7) EC_TEMP1/EC_TEMP2

8) D_LED1/D_LED2

9) LED_CPU

10) LED_C1/LED_C2

11) SATA3 0/1/2

12) SATA3 3

13) SATA_DOM0

14) M2A_CPU/M2B_SB

15) F_ PANEL

16) F_ AUDIO

17) F_U32

18) F_USB1/F_USB2

19) COM

20) TPM

21) CLR_CMOS

22) BAT

23) CPU/DRAM/VGA/BOOT

24) Q-FLASH_PLUS

25) F_U32C

1254

18 15 1317 211016

208

3 8 106

- 14 -

DEBUG

PORT

G.QBOFM

131

ATX

1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON (soft On/Off)

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 NC

95VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V (Only for 2x12-pin

ATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND (Only for 2x12-pin

ATX)

ATX_12V:

Pin No. Denition Pin No. Denition

1 GND (Only for 2x4-pin 12V) 5 +12V (Only for 2x4-pin

12V)

2 GND (Only for 2x4-pin 12V) 6 +12V (Only for 2x4-pin

12V)

3 GND 7 +12V

4 GND 8 +12V

DEBUG

PORT

G.QBOFM

ATX_12V

- 15 -

NOTE: Before connecting the 12V power

connector, make sure to remove the CPU

power connector cover as indicated on the

left. Gently press the front portion of the CPU

power connector cover to release and pull it

up to remove it.

5) SYS_FAN5_PUMP/SYS_FAN6_PUMP (System Fan/Water Cooling Pump Headers)

The fan/pump headers are 4-pin. Most fan headers possess a foolproof insertion design. When connecting

a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The

speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation,

it is recommended that a system fan be installed inside the chassis. The header also provides speed control

forawatercoolingpump,refertoChapter2,"BIOSSetup,""Settings\SmartFan5,"formoreinformation.

6) CPU_OPT (Water Cooling CPU Fan Header)

The fan header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a foolproof

insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black

connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control

design.

DEBUG

PORT

G.QBOFM

Pin No. Denition

1 GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

Pin No. Denition

1 GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

3/4) CPU_FAN/SYS_FAN1/2/3/4 (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•Thesefanheadersarenotcongurationjumperblocks.Donotplaceajumpercapontheheaders.

CPU_FAN SYS_FAN3SYS_FAN1/SYS_FAN2/

SYS_FAN4

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SYS_FAN6_PUMP

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SYS_FAN5_PUMP

DEBUG

PORT

G.QBOFM

Pin No. Denition

1 GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

- 16 -

8) D_LED1/D_LED2 (Addressable LED Strip Headers)

The headers can be used to connect a standard 5050 addressable LED strip, with maximum power rating

of 5A (5V) and maximum number of 1000 LEDs.

Pin No. Denition

1 V (5V)

2 Data

3 No Pin

4 GND

1 1

Connect your addressable LED strip to the header. The power pin

(marked with a triangle on the plug) of the LED strip must be connected

to Pin 1 of the addressable LED strip header. Incorrect connection may

lead to the damage of the LED strip.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

D_LED1 D_LED2

7) EC_TEMP1/EC_TEMP2 (Temperature Sensor Headers)

Connect the thermistor cables to the headers for temperature detection.

Pin No. Denition

1SENSORIN

2 GND

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

9) LED_CPU (CPU Cooler LED Strip/RGB LED Strip Header)

 TheheadercanbeusedtoconnectaCPUcoolerLEDstriporastandard5050RGBLEDstrip(12V/G/R/B),

with maximum power rating of 2A (12V) and maximum length of 2m.

Pin No. Denition

1 12V

2 G

4 B

ConnecttheCPUcoolerLEDstrip/RGBLEDstriptotheheader.The

power pin (marked with a triangle on the plug) of the LED strip must

be connected to Pin 1 (12V) of this header. Incorrect connection may

lead to the damage of the LED strip.

Forhowtoturnon/offthelightsoftheLEDstrippleasevisitthe"UniqueFeatures"webpageof

GIGABYTE's website.

RGBLED

Strip

12V

DEBUG

PORT

G.QBOFM

Addressable LED

Strip

- 17 -

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

10) LED_C1/LED_C2 (RGB LED Strip Headers)

 Theheaderscanbeusedtoconnectastandard5050RGBLEDstrip(12V/G/R/B),withmaximumpower

rating of 2A (12V) and maximum length of 2m.

Pin No. Denition

1 12V

2 G

4 B

ConnectoneendoftheRGBLEDstripextensioncabletotheheader

andtheotherendtoyourRGBLEDstrip.Theblackwire(markedwith

a triangle on the plug) of the extension cable must be connected to

Pin 1 (12V) of this header. The 12V pin (marked with an arrow) on the

other end of the extension cable must be lined up with the 12V of the

LED strip. Be careful with the connection orientation of the LED strip;

incorrect connection may lead to the damage of the LED strip.

Forhowtoturnon/offthelightsoftheLEDstrippleasevisitthe"UniqueFeatures"webpageof

GIGABYTE's website.

LED_C2

LED_C1

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

12VRGB

BG12VR

12V

RGBLED

Strip

12VRGB

BG12VR

11) SATA3 0/1/2 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device. The SATA connectors support

RAID0,RAID1,andRAID10.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguring

aRAIDarray.

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5RXN

6RXP

7 GND

SATA3 0

DEBUG

PORT

G.QBOFM

SATA3

DEBUG

PORT

G.QBOFM

- 18 -

14) M2A_CPU/M2B_SB (M.2 Socket 3 Connectors)

 TheM.2connectorssupportM.2SATASSDsorM.2PCIeSSDsandsupportRAIDconguration.Please

notethatanM.2PCIeSSDcannotbeusedtocreateaRAIDseteitherwithanM.2SATASSDoraSATA

harddrive.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguringaRAIDarray.

Follow the steps below to correctly install an M.2 SSD in the M.2 connector.

Step 1:

Locate the M.2 connector where you will install the M.2 SSD, use a screwdriver to unfasten the screw on

the heatsink and then remove the heatsink.

Step 2:

Locate the proper mounting hole based on the length of your M.2 SSD drive. If needed, move the standoff

to the desired mounting hole. Insert the M.2 SSD into the M.2 connector at an angle.

Step 3:

PresstheM.2SSDdownandthensecureitwiththescrew.Replacetheheatsinkandsecureittotheoriginal

hole.Makesuretoremovetheprotectivelmfromthebottomoftheheatsinkbeforereplacingtheheatsink.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

80110 60 42

M2A_CPU

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

80110 60 42

M2B_SB (Note)

(Note) The PCIEX4 slot shares bandwidth with the M2B_SB connector. The PCIEX4 slot becomes unavailable

when a device is installed in the M2B_SB connector.

12) SATA3 3 (SATA 6Gb/s Connector)

The SATA connector supports SATA DOM device. The SATA connectors conform to SATA 6Gb/s standard

and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single

SATAdevice.TheSATAconnectorsupportsRAID0,RAID1,andRAID10.RefertoChapter3,"Conguring

aRAIDSet,"forinstructionsonconguringaRAIDarray.

Pin No. Denition Pin No. Denition

1 GND 6 RXP

2 TXP 7 GND

3 TXN 8 +5V

4 GND 9GND

5RXN

SATA3

DEBUG

PORT

G.QBOFM

13) SATA_DOM0 (SATA DOM Power Header)

The header can provide power to SATA DOM devices.

Pin No. Denition

1 +5V

2 GND

3 NC

-19-

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has

different wire assignments, please contact the chassis manufacturer.

15) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

on the chassis to this header according to the pin assignments below. Note the positive and negative pins

before connecting the cables.

System Status LED

S0 On

S3/S4/S5 Off

•PW (Power Switch):

Connects to the power switch on the chassis front panel. You may

congure the way to turn off your system using thepower switch

(refertoChapter2,"BIOSSetup,""Settings\PlatformPower,"formore

information).

•SPEAK (Speaker):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•PLED/PWR_LED (Power LED):

Connects to the power status indicator

on the chassis front panel. The LED is on

when the system is operating. The LED is

off when the system is in S3/S4 sleep state

or powered off (S5).

•HD (Hard Drive Activity LED):

Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive

is reading or writing data.

•RES (ResetSwitch):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

ifthecomputerfreezesandfailstoperformanormalrestart.

•CI (Chassis Intrusion Header):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has

been removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC: No connection.

Power LED

DEBUG

PORT

G.QBOFM

CI-

CI+

PWR_LED-

PWR_LED+

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

Power LED

HD-

RES+

HD+

RES-

Hard Drive

Activity LED

Reset

Switch Chassis Intrusion

Header

Power Switch Speaker

PWR_LED-

16) F_AUDIO (Front Panel Audio Header)

 ThefrontpanelaudioheadersupportsHighDenitionaudio(HD).Youmayconnectyourchassisfront

panel audio module to this header. Make sure the wire assignments of the module connector match the

pin assignments of the motherboard header. Incorrect connection between the module connector and the

motherboard header will make the device unable to work or even damage it.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

10 2

Pin No. Denition Pin No. Denition

1 MIC2_L 6 Sense

2 GND 7 FAUDIO_JD

3MIC2_R 8 No Pin

4 NC 9LINE2_L

5LINE2_R 10 Sense

- 20 -

La pagina sta caricando ...

Gigabyte B550 VISION D-P Manuale del proprietario

Marca: Gigabyte

Modello: B550 VISION D-P

Categoria: Schede madri

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Gigabyte B550 VISION D-P Owner's manual

Gigabyte B550 VISION D-P Manuale del proprietario

Gigabyte B550 VISION D-P Manuale del proprietario

in altre lingue

Documenti correlati