DoorBird D10x Guida d'installazione

VERSION ., MIN. HW .

Page 1-19

Installation Manual

IP Video Door Station

D10x Series

Seite 20-39

Installationsanleitung

IP Video Türstation

D10x Serie

Page 40-58

Manuel d´installation

Interphone vidéo IP

Série D10x

Página 59-77

Manual de Instalación

Videoportero IP

Serie D10x

Pagina 78-95

Manuale di installazione

Videocitofono IP

Serie D10x

D10X

2

INSTALLATION MANUAL

Read these instructions carefully before starting to use any components.

Keep the manual so you can refer to it at a later date if required. If you hand

over the device to other persons for use, please hand over the operating

manual as well.

You can always ﬁnd the most up-to-date version of the installation manual

on www.doorbird.com/support

To make things easier we use the term “device” for the product “IP Video

Door Station” and “mobile device” for a smartphone or tablet.

Liability

Every care has been taken in the preparation of this document.

Please inform Bird Home Automation GmbH of any inaccuracies or omissions.

Bird Home Automation GmbH cannot be held responsible for any technical

or typographical errors and reserves the right to make changes to the product

and manuals without prior notice. Bird Home Automation GmbH makes no

warranty of any kind with regard to the content of this document, including,

but not limited to, the implied warranties of merchantability and ﬁtness for

a particular purpose. Bird Home Automation GmbH shall neither be liable

nor responsible for incidental or consequential damages in connection with

the furnishing, performance or use of this material. This product is only to

be used for its intended purpose.

Equipment Modiﬁcations

This equipment must be installed and used in strict accordance with the

instructions given in the user documentation. This equipment contains no

components that require service by the user. Unauthorized equipment

changes or modiﬁcations will invalidate all applicable regulatory certiﬁcations

and approvals.

Symbols used

Caution: Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Danger: Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Warning: Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Notice: Indicates a situation which, if not avoided, could result

in damage to property.

NOTICE

3

ENGLISHENGLISH

Note: Indicates useful information which helps in getting the

most out of the product.

Hazard information

• Mounting, installation and servicing work on electrical devices may

only be performed by a qualiﬁed eletrician. Failure to observe this

regulation could result in the risk of serious damage to health or fatal

injury due to electric shocks.

• Devices with 110-240 V connection: The device may only be connected

to an easily accessible power socket outlet. The mains adapter must

be pulled out if a hazard occurs.

• For power supply, only use the original plug-in mains adapter

delivered with the device or a recommended PoE-Switch/PoE-Injector

as speciﬁed in this manual.

• Because of electrostatic charging, direct contact with the circuit board

can result in destruction of the device. Direct contact with the circuit

board must therefore be avoided at any time.

• Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.

• Do not use the device if there are signs of damage to the housing,

control elements or connecting sockets, for example, or if it

demonstrates a malfunction. If you have any doubts, please have

the device checked by an authorized expert.

• Do not open the device. This voids the warranty of the device. The

device does not contain any parts that can be maintained by the

user. In the event of an error, please have the device checked by an

authorized expert.

• For safety, approval and licensing reasons (CE/FCC/IC etc.),

unauthorized change and/or modiﬁcation of the device is not

permitted.

• The device is not a toy: do not allow babies and children to play with

it.

• To avoid the danger of suffocation, keep any packing materials away

from babies and children. Plastic ﬁlms/bags, pieces of polystyrene, etc.

are not a toy and can be dangerous in the hands of a child. Discard

WARNING

Important: Indicates signiﬁcant information which is essential

for the product to function correctly.

4

any packing materials immediately after removing the product. Do not

reuse packing materials.

• Always lay cables in such a way that they do not become a risk to

people and domestic animals.

• Voltage is applied to parts within the equipment. Do not touch any

parts that are not associated with the installation, wiring, or connection.

Electric shock could result.

• On devices which are not marked as weather-proof: Keep the device

away from water or any other liquid.

• Do not install or make any wire terminations while power supply is

plugged in. It can cause eletric shock or damage to the device.

• Before turning on power, make sure wires are not crossed or shorted. If

not, ﬁre or eletric shock could result.

• High voltage may be present internally. Do not open the device.

Electric shock could result.

• The device is not of explosion-proof. Do not install or use near gases or

ﬂammable materials. Fire or explosion could result.

• Do not install two power supplies in parallel to a single input. Fire or

damage to the device could result. Be sure to connect a single power

supply to the device.

• Do not connect any terminal on the device to an AC power line. Fire or

electric shock could result.

• Keep AC cord from being marred or crushed. If the AC cord is fractured,

ﬁre or electric shock could result.

• Do not plug or unplug with wet hands. Electric shock could result.

• Do not put any metal or ﬂammable material into the device. Fire,

electric shock, or device trouble could result.

• Existing wiring may contain high voltage AC electricity. Damage to the

device or electric shock could result. Wiring and installation must be

done by a qualiﬁed eletrician.

• When mounting the device on a wall or ceiling, install the device in a

convenient location, but not where it could be jarred or bumped. Injury

could result.

• On devices with ground terminals, connect to an earth ground.

Otherwise ﬁre or malfunction could result.

• On devices with plastic or real glass, do not put high pressure on the

glass. If fractured, injury could result.

WARNING

5

ENGLISHENGLISH

• On devices with LCD, if LCD is punctured, do not allow contact with the

liquid crystal inside. Injury could result. If necessary, gargle your mouth

and clean your eyes or skin with clear water for at least 15 minutes and

consult your doctor.

• Do not put anything on the device or cover the device with cloth,

silicone, glue, coating, separate covering etc. Fire or device issues could

result.

• Do not install the device in any of the following locations. Fire, electric

shock, or device trouble could result.

 Places under direct sunlight or places near heating equipment that

varies in temperature.

 Places subject to dust, oil, chemicals, hydrogen sulﬁde (hot spring).

 Places subject to moisture and humidity extremes, such as bathrooms,

cellars, greenhouses, etc.

 Places where the temperature is very low, such as inside a refrigerated

area or in front of an air conditioner.

 Places subject to steam or smoke (e.g. near heating or cooking surfaces).

 Where noise generating devices such as dimmer switches or inverter

electrical appliances are closeby.

 Locations subject to frequent vibration or impact.

• On devices with intercom, be sure to perform a call test with low audio

volume on both intercom devices. A sudden call etc. may arrive causing

for example damage to your ear.

• If the device does not operate properly, unplug the power supply.

• All devices which are not marked as weather-proof are designed for

indoor use only. Do not use outdoor.

• On devices which are marked weather-proof: Do not spray with high-

pressure water. Device issues could result.

• We do not assume any liability for damage to property or personal injury

caused by improper use or the failure to observe the

• hazard information. In such cases, any claim under warranty ceases. For

consequential damages, we assume no liability!

6

Safety instructions

• The device shall be used in compliance with local laws and regulations.

• Store the device in a dry and ventilated environment.

• Avoid exposing the device to shocks or heavy pressure.

• Do not install the device on unstable brackets, surfaces or walls. Make

sure the material is strong enough to support the weight of the device.

• Use only applicable tools when installing the device. Using excessive

force with tools could cause damage to the device.

• Do not use chemicals, caustic agents, or aerosol cleaners.

• Use a clean dry cloth for cleaning.

• Use only accessories that comply with technical speciﬁcation of the

device. These can be provided by Bird Home Automation GmbH.

• Use only spare parts provided by or recommended by Bird Home

Automation GmbH.

• Do not attempt to repair the device by yourself. Contact Bird Home

Automation GmbH for service matters.

• Keep the device more than 1 m (3.3‘) away from microwave, radio, TV,

wireless router and any other wireless devices.

• On devices with intercom or built-in speaker or built-in microphone or

signal transmission functions, keep the wires more than 30 cm (12‘‘)

away from AC 100-240 V wiring. AC induced noise and/or device

malfunction could result.

• Install the device in an area that will be accessible for future inspections,

repairs and maintenance.

• If the device is used close to a cellular phone, the device may malfunction.

• The device can be damaged if dropped. Handle with care.

• The device turns inoperative during power failure.

• On devices with intercom or built-in speaker or built-in microphone,

in areas where cellular or Radio / TV broadcasting station antennas are

closeby, the device may be affected by radio frequency interference.

• On devices with LCD screen, it must be noted in advance that the LCD

panel, though manufactured with very high precision techniques,

inevitably will have a very small portion of its picture elements always lit

or not lit at all. This is not considered a device malfunction.

NOTICE

7

ENGLISHENGLISH

• On devices with intercom, due to the environmental sound around

the device, it may hinder smooth communication, but this is not a

malfunction.

• On devices with Username/Password, the Username/Password to access

the device is the customer‘s responsibility. Make sure to use a password

that cannot be easily guessed by a third party. We recommend that

you change the Password on a regular basis.

• We will, under no circumstances, be liable for damage that occurs due

to failures in power supply, network equipment or terminal devices;

failures due to Internet providers and cellular network providers; failures

such as disconnected lines and other losses in communication, which

makes it impossible to provide this service as well as in any way delay

this service due to any other causes outside of our responsibility; or if an

error or missing data occurs during transmission.

Information on disposal for users of waste electrical & electronic

equipment (private household)

This symbol on the products and/or accompanying documents means that

used electrical and electronic products should not be mixed with general

household waste. For proper treatment, recovery and recycling, please take

these products to designated collection points, where they will be accepted

an a free of charge basis. Alternatively, in some countries you may be able to

return your products to your local retailer upon the purchase of an equivalent

new product. Disposing of this product correctly will help to save valuable

resources and prevent any potential negative effects on human health and

the environment which could otherwise arise from inappropriate waste

handling. Please contact your local authority for further details of your nearest

designated collection point. Penalties may be applicable for incorrect disposal

of this waste, in accordance with national legislation.

Information on disposal in other countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this

product, please contact your local authorities or dealer and ask for the correct

method of disposal.

8

COMPONENTS

Contents

 1x DoorBird Video Door Station

 1x Power supply unit (mains adaptor) with four country-speciﬁc adaptors

 1x Cable with plug for the power supply (black, red)

 1x Cable with plug and RJ45 jack for the network cable (white-orange,

orange, white-green, green)

 1x Cable with plug for the network cable (white-orange, orange,

white-green, green), alternatively to the cable with plug and RJ45 jack

 1x Cable with plug for the electric door opener (purple, purple)

 1x Cable with plug for the electric door chime (blue, blue)

 1x Cable with plug for the door-opening button (yellow, yellow)

 Several crimp connectors

 4x Phillips countersunk head screws for the wall mounting plate, long

 4x Phillips countersunk head screws for the wall mounting plate, short

 4x Dowels

 1x Safety screw

 1x Screwing-tool for the safety screw

 1x Wall mounting plate with sealing ring (installation on wall surface)

 1x Installation manual

 1x Quickstart guide

Warranty Information

For information about the device warranty, see www.doorbird.com/warranty

Transportation

When transporting the device, use the original packaging or

equivalent to prevent damage to the device.

NOTICE

9

ENGLISHENGLISH

VIDEOS

Need help with the installation? Be sure to watch our installation videos

which can be found on http://www.doorbird.com/support

Each individual step of the installation is clearly documented in the videos.

Video door station

1) Night vision

Extra bright infra-red LEDs, effective

during the hours of darkness

(infra-red light invisible to the

human eye, 850nm)

2) HDTV video

Ultra wide-angle hemispheric

lens, 180°

3) Loudspeaker

Large-sized and speech enhanced

broadband speaker

4) Motion sensor

180° Infrared motion sensor

for alarms

5) Stainless-Steel Button

With illuminated LED ring (at night),

also acts as Diagnostic-LED

6) Microphone

With active noise cancellation

7) Light sensor

For the night-vision mode

8) Locking positions

For the mounting plate

9) Connection terminal

For the power supply,

door chime, etc.

10) Screw opening

For the safety screw

Night vision

HDTV video

Loudspeaker

Motion sensor

Stainless-Steel

Button

Microphone

Light sensor

backfront

1 8

9

10

2

3

4

5

6

7

10

INSTALLATION

All steps below should be carried out carefully by a competent adult, taking

into consideration any applicable safety regulations. Should you have any

questions, please contact us or a competent specialist directly. Please ensure

that all wires used for the installation are undamaged along their entire

length and approved for this type of use.

Network speed and network components

Please ensure that the upload speed of your Internet connection is at least

0.5 Mbps. You can also carry out a speed test at any time via the DoorBird

app. The user experience is only as good as your network speed, network sta-

bility and quality of your network components, such as your Internet router

and WiFi access points or WiFi repeaters. Please also make sure that your net-

work components are no older than two years old, have been manufactured

by a well-known manufacturer, and have the latest firmware installed.

Should these requirements not be fulfilled, it may happen, for example that

the performance of audio and video is poor or push notifications are delayed

or do not arrive on your smartphone or tablet at all.

High-speed Internet (via landline): DSL, cable or optical fibre

Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP

STEP 1: SWITCHING OFF POWER

Switch off the power to all wires leading to the assembly location, i.e. the

door chime, electric door opener, power supply unit for the video door

station etc..

STEP 2: DISMANTLING THE EXISTING DOORBELL

Should there already be a doorbell on the exterior wall of the house, please

dismantle it.

STEP 3: DETERMINING THE ASSEMBLY LOCATION

The video door station uses an ultra wide-angle hemispheric lens so that

even when the person is a minimum distance of 50 cm (19.68 inches) away

from the video door station, a low installation height is sufficient. The lens is

therefore not mechanically adjustable. The camera lens should be located

at an altitude of at least 145 cm (57 inches). You may check this prior to the

final mounting. Press the mounting plate against the wall at the desired

installation site and mark the boreholes with a pencil. Remove the mounting

plate again. Ensure that no cables are to be found in the wall behind

the boreholes.

11

ENGLISHENGLISH

Do not expose the device to direct sunlight. The housing temperature

can exceed the maximum allowed temperature limit. This can result

in damage of electric and mechanic components of the device and

injuries especially when touching exterior parts of the device. White

and bright silver-colored front plates absorb less sunlight than dark

ones.

An image sensor must not be exposed to direct sunlight for an

extended period of time. Direct sunlight will “blind” the camera

and may permanently bleach the small color filters on the image

sensor chip.

Any defects caused by direct sunlight is not covered by warranty.

STEP 4: POWER SUPPLY

The video door station can be powered by two simple doorbell wires using

the power-supply unit (mains adaptor) supplied with it or via PoE (Power

over Ethernet) using a network cable. The video door station can alternatively

also be supplied with a DIN-rail power supply unit that you can obtain from

us directly.

The video door station does not use battery power. The use of a mains power

supply permits the transmission and display of on-demand live video at any

time and not only if a visitor has pressed the doorbell.

Power supply using the power-supply unit (mains adaptor)

Two insulated wires are required to power the video door station by plugging

it into the mains. These wires are normally already there and are freely

accessible once you have removed the previous doorbell. Only use the power

supply unit provided along with the video door station, or a DIN-rail power

supply unit that you can obtain from us separately, since this has been spe-

cially stabilized electrically and is equipped with an integrated audio interfe-

rence reduction device. Other power supply units may destroy the video door

station or cause poor transmission quality. The warranty automatically expi-

res if you use a different power supply unit. The power supply unit is plugged

into a wall socket inside your house, usually where the two wires from your

previous doorbell come out of the wall in the interior of the house.

Do not plug the power supply unit into the wall socket yet. Connect the po-

wer supply unit inside the house with the crimp connector provided and the

two wires that you would like to use to power the device.

NOTICE

12

STEP 5: FURTHER CONNECTIONS (OPTIONAL)

If desired, connect additional wires to the installation site of the video door

station. The wires or connection options mentioned in this section are optional.

Be sure to use

four insulated,

shielded and

twisted wires of

a network cable

in accordance

with the Cat.5

standard or

better.

Connecting the unit to a network

You can connect the video door station to your existing

network via WiFi, or alternatively use a network cable

(Ethernet). For reasons of network stability, we principally

recommend using a network cable, as WiFi is sensitive to

interference (range, house walls acting as shields, relia-

bility of performance, third party WiFi networks, wireless

transmitters causing interference in the area, etc.).

The video door station can be powered by PoE or using

the power supply unit provided. If you use PoE as a

source of power, the WiFi interface of the video door

station remains inactive.

Use only four wires (1, 2, 3 and 6) of a network cable that

meets the Cat.5 standard or a better one. The other four

wires of the network cable (4, 5, 7 and 8) are not required.

Connect the network cable in the house to your

Internet router or to your PoE switch or PoE injector

that is connected to your Internet router.

Be sure to use four insulated, shielded and twisted wires

of a network cable in accordance with the Cat.5 standard

or better.

6 (R-)

3 (R+)

2 (T-)

1 (T+)

Power supply via PoE (as an alternative)

To power the video door station via a PoE switch (e.g. D-Link DGS-1008P) or

PoE injector (e.g. TP-Link TL-PoE150S) in accordance with the PoE standard

IEEE 802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a

Cat.5 cable or better are to be used. A Cat.5 cable or better must be used as

network signals can only be transmitted over completely insulated, shielded

and twisted cables. If you use PoE as a source of power, the WiFi interface of

the video door station is automatically inactive, and the four wires for PoE

then simultaneously form the data link. The video door station won’t start

if your PoE Switch or PoE injector does not support the PoE Standard IEEE

802.3af Mode A (see Diagnostic-LED and Diagnostic-Sounds).

1. Disconnect the PoE switch or PoE injector from the power grid.

2. Place the network cable in the installation site of the video door station.

Do not combine the power supply from the power supply unit (mains adaptor)

with the power supply via PoE.

13

ENGLISHENGLISH

Electric door openers

The video door station has a zero-potential relay contact

for a standardised electric door, gate or garage opener

(two wires). There is the possibility of switching on all

electric door openers that work at a maximum power of

1A in the voltage range of up to 24V (AC/DC). The video

door station does not provide its own power supply for

the electric door opener. This is provided through the

separate power supply of the electric door opener. You can

learn more about the installation of the power supply

from the instruction manual or technical specifications of

your door opener. Should you have any questions about

this, please contact the manufacturer of your door opener.

You can find compatible electric door opener and a sample

wiring diagram at www.doorbird.com/support

Conventional electric door chime

If someone rings your video door station, you will imme-

diately receive a push notification with sound/vibration

on your smartphone or tablet. In addition the video door

station comes with a zero-potential relay contact for

connecting a conventional electric door chime inside

the building. The relay contact can be used to activate

the separate operating voltage of the door chime or the

door chime via its trigger input. If the operating voltage

of the door chime is activated, it should not be greater

than 24V (AC/DC). The power consumption should not

exceed 1A. The video door station does not provide its

own power supply for the door chime. This is provided

through the separate power supply of your conventional

door chime. Should you have any questions, please con-

tact the manufacturer of your door chime. You can find

compatible door chimes and a sample wiring diagram at

www.doorbird.com/support

Conventional door opener button

If an electric door opener is connected to the video door

station, the door opener can be opened by App and also

be directly controlled via a zero-potential button to be

found in the interior of the building, i.e. a door opening

button. In addition, the door opener button is to be

connected to the connection terminal provided. Please

make sure to add no extra voltage on that contact. You

can find compatible door opener buttons and a sample

wiring diagram on www.doorbird.com/support

Two insulated

wires.

Two insulated

wires.

Two insulated

wires.

14

STEP 6: DOWELS

If the exterior wall of the house is not made of wood, you should drill four

holes 5 mm in diameter in the wall and then place the dowels provided into

the boreholes. If the exterior wall of the house is made of wood, you will

usually not require any dowels. There are special dowels for assembling the

video door station on an insulating wall, e.g. Fischer insulating dowels. Please

check with your insulating material manufacturer regarding which dowels

they recommend.

STEP 7: ATTACH THE MOUNTING PLATE

Put the wires that you would like to connect to the video door station

through the opening in the mounting plate provided. Position the mounting

plate against the exterior wall of the house and use the screws provided to

position it in the dowels or on the wall. The mounting plate for the video

door station has been designed in such a way that it can also be installed on

uneven walls, so it is not completely flat. The partially greater clearances at

the back also serve to stabilize temperature and moisture levels.

STEP 8: PREPARING THE WIRES

Remove about 5 mm of insulation material at the end of the wires that you

would like to connect to the video door station.

STEP 9: CONNECTING THE WIRES

It is possible to connect the video door station conveniently and safely via a

connection terminal with jacks on the reverse of the video door station.

The individual contacts on the connection terminal are labelled on the reverse

of the casing. Some connectors on the connection terminal may come provided

by us with cable. Please use appropriate crimp connectors or terminal strips

to connect the supplied cables with your wires. The accompanying crimp

connectors are weatherproof and are equipped with heat-shrink tubing which

can be sealed after assembly by, for example, carefully using a heat gun.

Please remove any cables on the connection terminal that you do not need.

15

ENGLISHENGLISH

Please take care when connecting the wires. Connecting the wires the wrong

way may destroy the video door station.

CONNECTOR DESCRIPTION WIRE

T+ White and orange network cable wire

(Number 1, Transmit Data +) white-orange

T- Orange network cable wire

(Number 2, Transmit Data -) orange

R+ White and green network cable wire

(Number 3, Receive Data +) white-green

R- Green network cable wire

(Number 6, Receive Data -) green

O1 Electric door opener

(zero potential) purple

O2 Electric door opener

(zero potential) purple

C1 Electric door chime (zero potential) blue

C2 Electric door chime (zero potential) blue

B1 Door-opening button yellow

B2 Door-opening button yellow

V- Power supply, negative pole (-) black

V+ Power supply, positive pole (+) red

T+ T- R+ R- O1 O2 C1 C2 B1 B2 V- V+

max. 0-24 V DC/AC, 1 A

max. 0-24 V DC/AC, 1A

0 V, 0A

15 V DC, 1A

16

STEP 10: FINAL ASSEMBLY

Mount the video door station on the mounting plate. The video door station

will click into the locking positions intended for the mounting plate. Use the

accompanying safety screw with the appropriate tool to fix the video door

station to the underside of the mounting plate.

STEP 11: ACTIVATING THE VIDEO DOOR STATION

Switch on the power to the wires leading to the assembly location again.

You can see whether you have connected the power supply properly from the

Diagnostic LED (it lights up once the power has been connected correctly

for up to five minutes and continuously in night-vision mode). The video door

station is ready for operation (booting up process, any software updates, etc.)

once it has emitted a short diagnosis sound from the integrated loudspeaker.

This may last for up to 5 minutes. Should you not hear a beep, please check

the power supply. Please also check whether you have used a wall-plug

power-supply and not PoE and whether you have connected the positive

pole and negative pole to the video door station correctly.

STEP 12: DOWNLOADING AND INSTALLING THE APP

Download the „DoorBird“ app by Bird Home Automation onto your mobile

device from the Apple app store or Google Play store. You can always find the

most up-to-date version of the App manual on www.doorbird.com/support

If you use WiFi for connecting the video door station to your Internet router,

first go to „Settings > WiFi Setup“ and follow the instructions.

If you have finished the WiFi set-up or have connected the video door station

to your Internet router by means of a network cable, go to „Settings > Add

device“ and click on the QR code icon in the „User“ field. Scan the user QR

code found on the „Digital Passport“ that accompanies the video door station.

If you have problems adding the video door station to the App please check

if the video door station is online ( www.doorbird.com/checkonline ). If the

video door station is not online, please check the WiFi or network cable

connection again.

Since Apple uses very high quality microphones, loudspeakers and digital audio

components that are perfectly in tune with one another, the voice quality with

an iPhone or iPad is usually noticeably better than with an Android smartphone

or Android tablet.

DIAGNOSTIC-LED

This LED light is only lit up for five minutes after the video door station has

been supplied with power (and continuously at night). It lights up as soon as

the video door station is supplied with power.

 Illuminated: Device is powered

17

ENGLISHENGLISH

DIAGNOSTIC-SOUNDS

After around two to five minutes, the video door station emits brief diagno-

stic sounds after it has been connected to the power grid.

 1x diagnostic sound: The video door station is connected to the Internet

 2x diagnostic sounds: The video door station is able to communicate with

the router, but cannot access the Internet

 3x diagnostic sounds: The video door station has no connection to the network

TECHNICAL SPECIFICATIONS

GENERAL

Power supply:

15V DC (power 110-240 V AC) or

Power over Ethernet (PoE 802.3af

Mode-A)

Connectors:

Power, electric door opener/strike,

door chime, door opener button,

network

Weather-proof:

Yes, IP65

Approvals:

CE, IC, FCC, IP65

Operating conditions:

-20 to +40°C / -4 to 104°F

Humidity 10 to 85% RH

(non condensing)

Scope of delivery:

Video Door Station, mounting plate,

power supply unit (world-wide,

110-240V), DIN-rail power supply

sold separately, screw package,

quick start guide

Warranty:

see www.doorbird.com/warranty

CURRENT SYSTEM REQUIREMENTS

System requirements:

Mobile Device: Newest iOS on

iPhone/iPad, newest Android on

Smartphone/Tablet

Internet: High-Speed Landline

Broadband Internet connection, DSL,

Cable or ﬁber optic, no socks or Proxy

server

Network: 802.11 b/g/n 2.4GHz or

Ethernet Network, with DHCP

Recommended installation height:

Camera lens should be at a min.

height of 145 cm (57 in)

VIDEO

Camera:

HDTV 720p, dynamic (VGA – HDTV)

Lens:

High-end ultra wide-angle hemispheric

lens 180° horizontal, 90° vertical,

straightened, IR-capable

Night-vision:

Yes, light sensor, automatic IR-cut

ﬁlter, 12 IR-LEDs

18

AUDIO

Audio components:

Speaker and microphone, echo and

noise cancellation

Audio streaming:

Two-way duplex

NETWORK

WiFi:

802.11 b/g/n 2.4 GHz

Ethernet:

Connector, PoE 802.3af Mode-A

MOTION SENSOR

Type:

Passiv infrared sensor (PIR)

Detection angle:

180°

Range:

2-8 m (79-315 in)

depends on environment

INTEGRATED WIRELESS MODULES

WiFi:

2,4GHz, internal antenna

OPTIONAL ACCESSORIES

Sold separately:

see www.doorbird.com/buy

Errors and omissions excepted.

LEGAL NOTES

General remarks

1. DoorBird is a registered trademark of Bird

Home Automation GmbH.

2. Apple, the Apple logo, Mac, Mac OS,

Macintosh, iPad, Multi-Touch, iOS, iPhone

and iPod touch are trademarks of Apple Inc.

3. Google, Android and Google Play are

trademarks of Google, Inc.

4. The Bluetooth® word mark and logos are

registered trademarks of Bluetooth SIG, Inc.

5. All other company and product names may

be trademarks of the respective companies

with which they are associated.

6. We reserve the right to make changes to

our products in the interests of technical

advancement. The products shown may also

look different from the products supplied

based on ongoing enhancement.

7. Reproducing or using texts, illustrations and

photos from this instruction manual in any

media – even if only in the form of excerpts

– shall only be permitted with our express

written consent.

8. The design of this manual is subject to

copyright protection. We do not accept

any liability for any errors or any erroneous

content or printing errors (even in the case

of technical specifications or within graphics

and technical sketches).

9. Our products are in compliance with

all technical guidelines, electrical and

telecommunications regulations applicable

in Germany, the EU and the USA.

10. Our products and also the components

contained therein (ICs, software, etc.)

may only be used for civilian non-military

purposes.

Data privacy and data security

1. For maximum security, the device uses the

same encryption technologies as are used

in online banking. For your security, no port

forwarding or DynDNS is used either.

2. The data centre location for remote access

over the Internet by means of an App is

obligatory in the EU if the determined

Internet IP-Address location of the device is

within the EU. The data centre is operated

in line with the most stringent security

standards.

3. Video, audio and any other surveillance

methods can be regulated by laws that vary

from country to country. Check the laws in

your local region before installing and using

this device for surveillance purposes.

19

ENGLISHENGLISH

If the device is a door-, indoor station or camera:

• In many countries video and voice signal may

only be transmitted once a visitor has rung the

bell (data privacy, configurable in the App).

• Please carry out the mounting in such a

way that the detection range of the camera

limits the device exclusively to the immediate

entrance area.

• The device may come with a visitor history and

motion sensor. You can activate/deactivate

this function if required.

If necessary, indicate the presence of the device

in a suitable place and in a suitable form.

Please observe any relevant country-specific

statutory regulations concerning the use of

surveillance components and surveillance

cameras applicable at the installation site.

Check with the property owner and your house

community if you are allowed to install and use

this product. Bird Home Automation GmbH

cannot be held responsible for any miss-use or

miss-configuration of this product, including

the unauthorized opening of a door.

Bird Home Automation cannot be held

responsible for damages caused by improper

existing installations or improper installation.

Software and operating system’s updates

(so-called “firmware updates”) are generally

automatically installed on the products of

Bird Home Automation GmbH via Internet,

if technically possible. Automatic firmware

updates keep the products‘ software up to

date so that they always work reliably, safely

and efficiently. Through further development,

features can be added, extended or slightly

changed. Major changes or limitations to

existing features will generally occur if Bird

Home Automation GmbH deems it necessary

(e.g. for data protection, data security or

stability reasons, or to keep them up to date).

When a firmware update is available, Bird

Home Automation GmbH‘s servers generally

automatically distribute it to all compatible

products connected to the Internet or Bird

Home Automation GmbH‘s servers. This process

is gradual and can take several weeks. As soon

as a product receives a firmware update, the

system will be installed and will restart by itself.

Installed firmware updates cannot be undone.

Since the products and software of Bird Home

Automation GmbH are not explicitly customer-

specific products, a customer cannot deny an

automatic update if the product is connected

to the Internet or to the Bird Home Automation

GmbH’s server.

Publisher

Bird Home Automation GmbH

Uhlandstraße 165

10719 Berlin

Germany

Web: www.doorbird.com

Email: [email protected]

It is possible that these manual still contains

typographical errors or printing errors.The

information in this manual will be checked

regularly and corrections will be made in the

next version. We accept no liability for errors

of a technical or printing nature and their

consequences.

20

INSTALLATIONSANLEITUNG

Lesen Sie diese Anleitung sorgfältig, bevor Sie die Komponenten in Betrieb

nehmen. Bewahren Sie die Anleitung zum späteren Nachschlagen auf!

Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben

Sie auch diese Bedienungsanleitung.

Die stets aktuelle Version der Installationsanleitung ﬁnden Sie unter

www.doorbird.com/de/support

Zur Vereinfachung der Begriffe verwenden wir „Gerät“ für das Produkt

„IP Video Türstation“ sowie „mobiles Endgerät“ für ein Smartphone/Tablet.

Haftung

Die Erstellung dieses Dokuments wurde sorgfältig vorbereitet. Bitte infor-

mieren Sie Bird Home Automation GmbH über etwaige Ungenauigkeiten

oder Unterlassungen. Bird Home Automation GmbH kann nicht für tech-

nische oder typografische Fehler verantwortlich gemacht werden und behält

sich das Recht vor, Änderungen an dem Produkt und den Handbüchern

ohne vorherige Ankündigung vorzunehmen. Bird Home Automation GmbH

übernimmt keinerlei Garantie in Bezug auf das in diesem Dokument ent-

haltene Material, einschließlich, aber nicht beschränkt auf die implizierten

Garantien der Marktgängigkeit und Eignung für einen bestimmten Zweck.

Bird Home Automation GmbH haftet nicht für Neben- oder Folgeschäden im

Zusammenhang mit der Bereitstellung, Durchführung oder Verwendung dieses

Materials. Das Gerät darf nur für den vorgesehenen Zweck verwendet werden.

Gerätemodifikationen

Dieses Gerät muss in Übereinstimmung mit den Anweisungen in der

Installationsanleitung installiert und verwendet werden. Dieses Gerät ent-

hält keine vom Benutzer zu wartenden Komponenten. Durch unbefugte

Gerätemodifikationen oder Änderungen erlöschen alle anwendbaren

Zertifizierungen und Zulassungen.

Verwendete Symbole

Achtung: Weist auf eine gefährliche Situation hin, die, falls

nicht verhindert, zum Tod oder schweren Verletzungen führt.

Warnung: Weist auf eine gefährliche Situation hin, welche,

falls nicht verhindert, zum Tod oder schweren Verletzungen

führen kann.

La pagina sta caricando ...

DoorBird D10x Guida d'installazione

DoorBird D10x Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti