dji GO 4 Guida utente

Marca: dji

Modello: GO 4

Tipo: Guida utente

SPARK

DISCLAIMER AND SAFETY

GUIDELINES

2017.10

V1.2

Contents

Safety at a Glance

NOTICE

Glossary

Pre-ight Checklist

Disclaimer and Warning

Before You Begin

Individual Parts

Regarding Genuine and Functional Parts 7

Camera 7

Gimbal 8

Compass 8

Propulsion Systems 8

DJI GO 4 App 9

Firmware 10

Product Care

Storage and Transportation 11

Maintenance and Upkeep 11

Flight Condition Requirements

Weather Conditions and Surrounding Environment 11

Interference with Communications 12

Operating the Aircraft Responsibly 12

Flight Modes, Functions and Warnings

Flight Modes 13

Return-to-Home 14

Low Battery 14

Vision System and 3D Sensing System 14

TapFly 15

ActiveTrack 15

Gesture Control 16

QuickShot 16

Compliance with Regulations & No Fly Zones

Regulations 17

No Fly Zones 18

Compliance Information

Safety at a Glance

1. Environmental Consideration

•

Always y at locations that are

clear

of magnetic or radio interference,

building and other obstacles

• DO NOT fly above or near large

crowds

•

Avoid ying at altitudes above

400

feet (120 m).*

•

Be very careful when ying

13,123

feet (4,000 m)

or more above sea

level.

•

Fly in moderate weather

conditions with temperatures between

32° to 104° F (0° to 40° C)

•

Please take additional caution while flying indoors because the aircraft

stabilization features may be interfered with.

•

DO NOT y when the wind speeds exceeding 10 m/s or 22 mph.

2. Pre-ight Checklist

•

Ensure the stickers on the camera, Vision System and 3D Sensing System are

removed before use.

•

Ensure the remote control device and aircraft batteries are

fully charged

•

Ensure the propellers are in

good condition

and

securely tightened

before each ight.

•

Ensure there is

nothing obstructing the motors

•

Only calibrate the compass when the DJI GO™ 4 app or the status indicator

prompt you to do so.

•

Check that the camera lens is

clean

and

free of stains

•

Altering or modifying the aircraft may impact its stability.

3. Operation

•

DO NOT touch the battery buckles while holding the aircraft to avoid it dropping off.

• Stay away

from the

rotating propellers and motors

•

Maintain

visual line of sight

of your aircraft at all times. .

• DO NOT

pull the left and right stick to the bottom inside corner at the same time

when the aircraft is airborne unless in an emergency situation.

• DO NOT answer incoming calls, text messages or do anything that may distract

you from operating your smart device to control the aircraft during ight.

• DO NOT

y under the inuence of

alcohols

drugs

• DO NOT

y closely above

reective surfaces

such as

water

snow

, as these

terrain may affect the performance of the Vision System.

•

In the instance of a

Low Battery Warning

, land the aircraft at a

safe location

•

After landing, rst stop the

motor

, then turn off the

Intelligent Flight Battery

, and

then turn off the

remote control device

•

When using TapFly

or ActiveTrack

features, be prepared to take control of the

aircraft by pushing the sticks. Please note that the aircraft will continue performing

the TapFly or ActiveTrack functions after you pushed the sticks. Press the STOP

button on the screen to exit such on-going functions completely.

•

While with advanced technology, the pilot’s sound discretion is required during

the ight. Safety and ight assistance features such as obstacle avoidance and

precise landing are designed to assist your operation, not to replace it.

•

Environmental conditions including lighting and obstacle’s texture may impact

the performance of the Vision System.

* The ight altitude restriction varies in different nations. DO NOT y above the maximum

altitudes set forth in your local laws and regulations.

The DJI

SPARK

is NOT

a toy and is NOT suitable

for children under the age

of 15.

Note that ‘Safety at a Glance’ only

provides a quick overview of the

safety tips. Make sure you read and

understand the remaining sections

of the Spark Disclaimer and Safety

Guidelines.

Fly in Open Areas Strong GPS Signal Maintain Line of Sight Fly Below 400 feet (120 m)

Avoid ying over or near obstacles, crowds, high voltage power lines, trees or bodies of water.

DO NOT

y near strong electromagnetic sources such as power lines and base stations since

it may affect the onboard compass.

Stay away from the rotating propellers and motors.

DO NOT use the aircraft in adverse weather conditions such as rain, snow, fog and wind

speeds exceeding 10 m/s or 22 mph.

•

The Vision System and 3D sensing system are disabled in certain situations.

Please refer to the User Manual for more information.

•

Please set the Return-to-Home Altitude higher than surrounding obstacles in the

DJI GO 4 app.

•

The RTH (Return-to-Home) feature does not enable the aircraft to automatically

return to a moving home point.

4. Maintenance and Upkeep

• DO NOT

use aged, chipped or broken propellers

•

Recommended storage temperature:

between 71° and 82° F (22° and 28° C)

•

Refer to the

Spark Intelligent Flight Battery Safety Guidelines

for more information

about the safe use of the battery.

5. Observe Local Laws and Regulations

• DO NOT

y in the No Fly Zones. You can nd relevant information on these areas at

http://www.dji.com/ysafe.

Please check with local aviation authorities for complete

lists and regulations of No Fly Zones.

•

The DJI No Fly Zone is not a replacement for

local government regulations

good judgment

. DO NOT y above the maximum altitudes set forth in your local

laws and regulations.

• Avoid ying in areas where rescue teams are actively using the airspace

≥

10m/s

No Fly Zone

Learn more at:

http://ysafe.dji.com/no-y

NOTICE

All instructions and other collateral documents are subject to change at the sole

discretion of SZ DJI TECHNOLOGY CO., LTD ("DJI"). For up-to-date product

information, visit http://www.dji.com and check on the product page.

Glossary

The following terms are used throughout this document to indicate various levels of

potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of

physical property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability

of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of

property damage, collateral damage, and serious injury OR create a high probability of

serious injury.

Read the ENTIRE user manual to become familiar with the

features of this product before operation. Failure to operate

the product correctly can result in damage to the product

or personal property and cause serious injury.

This is a sophisticated product. It must be operated with caution and common sense

and requires some basic mechanical ability. Failure to operate this product in a safe and

responsible manner could result in injury or damage to the product or other property.

This product is not intended for use by children. DO NOT use incompatible components

or alter this product in any way unless otherwise allowed by relevant documents

provided by SZ DJI TECHNOLOGY CO., LTD. These Safety Guidelines contain

instructions for safety, operation and maintenance. It is essential to read and follow all

of the instructions and warnings in the user manual, prior to assembly, setup or use, in

order to operate the product correctly and avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER THE AGE OF 15. THIS IS NOT A TOY.

Pre-ight Checklist

1. Ensure that you are using only genuine parts and that all parts are in mint

condition.

2. Ensure the remote control device and Intelligent Flight Battery are fully charged.

3. Ensure that there is no foreign object stuck to the camera lens, the Micro SD

card has been inserted into the aircraft, and the gimbal can rotate freely before

powering it on.

4. Keep the sensors of the Vision System and 3D Sensing System clean at all times.

5. Ensure the propellers are securely mounted and tightened onto the motors, and

the motors can start and function normally.

6. Follow the on-screen instructions to calibrate the compass.

7. Ensure the DJI GO 4 App and aircraft's rmware have been upgraded to the

latest version.

8. Ensure that your ight area is outside the No Fly Zones and ight conditions are

suitable for ying the aircraft.

9. Be sure that you are NOT ying under the inuence of alcohol, drugs or any

substance that may impair your cognitive abilities.

10. Be familiar with the selected ight mode and understand all safety functions and

warnings.

11. Be sure to observe all local regulations, obtain appropriate authorizations, and

understand the risks. REMEMBER: It is solely your responsibility to comply with

all ight regulations.

12. Please MAINTAIN VISUAL LINE OF SIGHT (WITH YOUR EYES) OF YOUR

AIRCRAFT AT ALL TIMES . Please do not only rely on rst person view camera

to control your aircraft.

13. Ensure the DJI GO 4 app is properly launched to assist your operation of the

aircraft. WITHOUT THE FLIGHT DATA RECORDED BY THE DJI GO 4 App, IN

CERTAIN SITUATIONS (INCLUDING THE LOSS OF YOUR AIRCRAFT) DJI MAY

NOT BE ABLE TO PROVIDE AFTERSALES SUPPORT TO YOU OR ASSUME

LIABILITY.

Disclaimer and Warning

This product is NOT a toy and is not suitable for children under the age of 15. Adults

should keep the aircraft out of the reach of children and exercise caution when

operating this aircraft in the presence of children.

While the product adopts advanced technology, inappropriate use of the product

could result in personal injury or property damages. Please read the materials

associated with the product before your rst use of the product. These documents

are included in the product package and are also available online on the DJI

product page at http://www.dji.com.

This product is a ying camera that offers easy ight when in good working order as set

forth below. Visit http://www.dji.com for the most current instructions and warnings and

http://knowbeforeyouy.org/ for more information about ight safety and compliance.

The information in this document affects your safety and your legal rights and

responsibilities. Read this entire document carefully to ensure proper conguration

before use. Failure to read and follow the instructions and warnings in this document

may result in product loss, serious injury to you, or damage to your aircraft.

By using this product, you hereby signify that you have read this disclaimer carefully

and that you understand and agree to abide by the terms and conditions herein.

EXCEPT AS EXPRESSLY PROVIDED IN DJI AFTER-SALES SERVICE POLICIES

AVAILABLE AT (HTTP://WWW.DJI.COM/SERVICE), THE PRODUCT AND ALL

MATERIALS, AND CONTENT AVAILABLE THROUGH THE PRODUCT ARE

PROVIDED “AS IS” AND ON AN “AS AVAILABLE” BASIS, WITHOUT WARRANTY OR

CONDITION OF ANY KIND, EITHER EXPRESS OR IMPLIED. DJI DISCLAIMS ALL

WARRANTIES OF ANY KIND, EXCEPT AS EXPRESSLY PROVIDED IN DJI AFTER-

SALES SERVICE POLICIES, WHETHER EXPRESS OR IMPLIED, RELATING TO THE

PRODUCT, PRODUCT ACCESSORIES, AND ALL MATERIALS, INCLUDING: (A)

ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, TITLE, QUIET ENJOYMENT, OR NON-INFRINGEMENT; AND (B) ANY

WARRANTY ARISING OUT OF COURSE OF DEALING, USAGE, OR TRADE. DJI

DOES NOT WARRANT, EXCEPT AS EXPRESSLY PROVIDED IN DJI LIMITED

WARRANTY, THAT THE PRODUCT, PRODUCT ACCESSORIES, OR ANY PORTION

OF THE PRODUCT, OR ANY MATERIALS, WILL BE UNINTERRUPTED, SECURE, OR

FREE OF ERRORS, VIRUSES, OR OTHER HARMFUL COMPONENTS, AND DO NOT

WARRANT THAT ANY OF THOSE ISSUES WILL BE CORRECTED.

DJI reserves the right to update this disclaimer and the safety guidelines. Please visit www.dji.

com and check your email periodically for the latest version. This disclaimer is made in various

language versions; in the event of divergence among different versions, the English version

shall prevail.

NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN, OBTAINED BY

YOU FROM THE PRODUCT, PRODUCT ACCESSORIES, OR ANY MATERIALS

WILL CREATE ANY WARRANTY REGARDING DJI OR THE PRODUCT THAT IS

NOT EXPRESSLY STATED IN THESE TERMS. YOU ASSUME ALL RISKS FOR

ANY DAMAGE THAT MAY RESULT FROM YOUR USE OF OR ACCESS TO THE

PRODUCT, PRODUCT ACCESSORIES, AND ANY MATERIALS. YOU UNDERSTAND

AND AGREE THAT YOU USE THE PRODUCT AT YOUR OWN DISCRETION AND

RISK, AND THAT YOU ARE SOLELY RESPONSIBLE FOR ANY PERSONAL INJURY,

DEATH, DAMAGE TO YOUR PROPERTY (INCLUDING YOUR COMPUTER SYSTEM

OR MOBILE DEVICE OR DJI HARDWARE USED IN CONNECTION WITH THE

PRODUCT) OR THIRD PARTY PROPERTY, OR THE LOSS OF DATA THAT RESULTS

FROM YOUR USE OF OR INABILITY TO USE THE PRODUCT.

SOME JURISDICTIONS MAY PROHIBIT A DISCLAIMER OF WARRANTIES AND YOU

MAY HAVE OTHER RIGHTS THAT VARY FROM JURISDICTION TO JURISDICTION.

DJI accepts no liability for damage, injury or any legal responsibility incurred directly

or indirectly from the use of this product. The user shall observe safe and lawful

practices including, but not limited to, those set forth in these Safety Guidelines.

Data Storage and Usage

When you use our mobile apps or our products or other software, you may provide

DJI with data regarding the use and operation of the product, such as ight telemetry

data (e.g., speed, altitude, battery life, and information about the gimbal and camera)

and operations record. Please refer to DJI Privacy Policy (available at dji.com/policy)

for more information.

Before You Begin

The following documents have been produced to help you safely operate and make

full use of your aircraft:

In the Box

Disclaimer and Safety Guidelines

Intelligent Flight Battery Safety Guidelines

Quick Start Guide

User Manual

Check all of the included parts listed in the

In the Box

and read the

Disclaimer and

Safety Guidelines

before ight. Then prepare for your rst ight by using the

Quick

Start Guide

and watching all of the tutorial videos on DJI’s ofcial website (http://

www.dji.com). If you have questions, refer to the

User Manual

in the app or on DJI’s

ofcial website for more comprehensive information. Make sure you fully understand

the functionality of each individual part, the ight condition requirements, the key

contingency warning functions/systems, and all government regulations before each

ight. If you have any questions or problems during the assembly, maintenance or

use of this product, please contact DJI or a DJI authorized dealer.

Individual Parts

Regarding Genuine and Functional Parts

To avoid component malfunction, serious injury, and property damage,

observe the following rules:

1. Use only genuine DJI parts or parts certied by DJI. Unauthorized parts or

parts from non-DJI certied manufacturers may cause system malfunctions

and compromise safety.

2. Ensure there are no foreign objects (such as water, oil, soil, sand, etc.) inside

of the aircraft or its components.

3. Ensure the aircraft and its components – including but not limited to the

camera, gimbal, compass, propulsion system, and battery – are all in good

working order, damage-free, and functioning well. Refer to the remaining

sections in this document for more details on how to ensure the functionality

of these components.

4. DO NOT modify or alter the aircraft, its components, and parts. Unauthorized

modication may cause malfunctions and affect the aircraft’s functionality

and safety.

Camera

To avoid possible serious injury and property damage, observe the following rule:

1. DO NOT block any ventilation holes on the camera as the heat generated may

hurt you and damage the device.

1. Check camera settings before use to make sure you can adjust them to t your

needs.

2. Test the camera by shooting a few test images and check that it is operating

correctly before shooting important pictures or videos.

3. DO NOT remove the Micro SD card from the aircraft when it is powered on.

4. Photos or videos cannot be transmitted or copied from the camera if the

Intelligent Flight Battery is powered off.

5. Be sure to power off the Intelligent Flight Battery correctly, otherwise your camera

parameters will NOT be saved and any recorded videos may be damaged.

NOTE: Regardless of the reason, DJI will not be responsible for any failure of

an image or video to be recorded or having been recorded in a way that is not

machine readable.

Gimbal

1. Precision elements in the gimbal may be damaged in a collision or impact, which

may cause the gimbal to function abnormally.

2. DO NOT apply external force to the gimbal after the gimbal is powered on.

3. DO NOT add any payloads to the gimbal, as this may cause the gimbal to

function abnormally or even lead to motor damage.

Compass

To avoid possible serious injury and property damage, observe the following rule:

1. Land immediately when obvious drifting occurs in ight, i.e., the aircraft does

NOT y in straight lines.

Only calibrate the compass when the DJI GO 4 app or the status indicator prompt you

to do so. Observe the following rules when calibrating your compass:

1. DO NOT calibrate your compass where there is magnetic interference, such as

interference by magnetite, parking structures, or steel reinforcements underground.

2. DO NOT carry ferromagnetic materials with you during calibration such as

cellular phones.

3. The DJI GO 4 app will prompt you to resolve the compass issue if the compass is

affected by strong interference after calibration is complete. Follow the prompted

instructions to resolve the compass issue.

Propulsion Systems

To avoid serious injury to yourself or others, which may be caused by the

rotating propellers and motors, observe the following rules:

Propellers

1. DO NOT use aged, chipped, or broken propellers.

2. Always power off the aircraft before touching the propellers.

3. Be aware of the sharp edges of the propellers when mounting or removing

the propellers. Wear gloves or take other protective measures when

touching the propellers.

4. Whenever necessary, use tools (e.g., wrench, screwdriver, pliers, etc.) to

remove or install the propellers.

5. Ensure the propellers are securely mounted and tightened to prevent them

from falling off the motors.

6. DO NOT turn on the motors when propellers are mounted and there are other

people or animals in the immediate vicinity.

7. Using third-party propellers may compromise the aerodynamics of the aircraft.

For a better and safer ight experience, we recommend you to use original DJI

propellers only.

Motors

1. Ensure the motors are securely mounted and rotating smoothly.

2. DO NOT attempt to modify the structure of the motors.

3. DO NOT touch or let your hands or body come in contact with the motors after

ight as they may be hot.

To avoid possible serious injury and property damage, observe the following rules:

1. DO NOT block any of the ventilation holes on the motors.

2. DO NOT block any of the ventilation holes on the body of the aircraft.

Motors

1. Keep the motors free of dust.

2. If a motor is stuck and unable to rotate freely, execute the landing command

immediately.

Electronic Speed Controllers

1. Ensure the ESCs sound normal when powered on.

DJI GO 4 App

1. Be sure to fully charge your tablet or mobile device before launching the DJI GO

4 App.

2. Mobile cellular data is required when using the DJI GO 4 app. Please contact

your wireless carrier for data charges.

3. If you are using a phone as your mobile display device, be sure to continue ying

safely when the phone receives an incoming call. DO NOT accept phone calls or

use the texting features during ight.

4. Read all prompted safety tips, warning messages, and disclaimers carefully. Be

familiar with the related regulations in your area. You are solely responsible for

being aware of all relevant regulations and ying in a way that is compliant.

a. Read and understand the warning messages before using the Auto-take off

and Auto-landing features.

b. Read and understand the warning messages and disclaimer before setting

the altitude beyond the default limit.

c. Read and understand the warning messages and disclaimer before switching

between ight modes.

d. Read and understand the warning messages and disclaimer prompts near or

inside the no y zone.

5. Land your aircraft immediately at a safe location if there is an alert shown on the

app.

6. Examine and check all warning messages on the checklist displayed in the app

prior to each ight.

7. Use the in-app simulator to practice your ight skills if you have never operated

the aircraft or if you do not have sufcient experience to be comfortable operating

the aircraft.

8. Beginner Mode is enabled by default when you launch the app for the rst time. The

aircraft’s altitude and ight distance is restricted when ying in Beginner Mode. We

recommend you y in Beginner Mode to perfect your ight skills. Operate the actual

aircraft only after you are condent that you have mastered adequate ight skills.

9. Cache the map data of the area where you intend to y the aircraft by connecting

to the Internet before each ight.

10. The app is designed to assist your operation. Please use your sound discretion

and DO NOT rely on the app to control your aircraft.

11. Your use of the app is subject to the DJI GO 4 app Terms of Use and DJI

Firmware

To avoid serious injury to children and animals, observe the following rule:

1. Keep children and animals at a safe distance during any rmware upgrade,

system calibration, and parameter setting procedures.

1. For safety, always update the rmware to the latest version when an upgrade

notication is shown in the DJI GO 4 app.

2. Firmware upgrade notifications will prompt you to proceed with an update

immediately or to update the rmware within three days. If you choose to ignore the

current rmware update, you are required to accept the prompted disclaimer. You

further understand and agree that the data including but not limited to user selection

records may be uploaded to and maintained on a DJI-designated server.

3. Be sure to download the rmware package le from the DJI ASSISTANT

Verify the rmware package le’s integrity before upgrading.

4. The remote control device may become unlinked from the aircraft after updating.

Re-link the remote control device and aircraft.

5. Be sure to check all connections and remove the propellers from the motors

before performing the rmware update.

Product Care

Storage and Transportation

To avoid serious injury to children and animals, observe the following rule:

1. Small parts, such as cables and straps, are dangerous if swallowed. Keep all

parts out of reach of children and animals.

1. Store the Intelligent Flight Battery and remote control device in a cool, dry place

away from direct sunlight to ensure the built-in LiPo battery does NOT overheat.

Recommended storage temperature: between 71° and 82° F (22° and 28° C) for

storage periods of more than three months. Never store in environments outside

the temperature range of 32° to 113° F (0° to 45° C).

2. DO NOT allow the camera to come into contact with, or become immersed

in, water or other liquids. If it gets wet, wipe dry with a soft, absorbent cloth.

Turning on an aircraft that has fallen into water may cause permanent component

damage. DO NOT use substances containing alcohol, benzene, thinners or

other ammable substances to clean or maintain the camera. DO NOT store the

camera in humid or dusty areas.

3. DO NOT connect this product to any USB interface that is older than version 2.0.

DO NOT connect this product to any "power USB" or similar devices.

Maintenance and Upkeep

1. Check every part of the aircraft after any crash or violent impact. If you have any

problems or questions, please contact a DJI authorized dealer.

Flight Condition Requirements

Weather Conditions and Surrounding Environment

The aircraft is designed to operate in good to moderate weather conditions. To

avoid collision, serious injury and property damage, observe the following rules:

1. DO NOT use the aircraft in severe weather conditions. These include wind

speeds exceeding 10 m/s (22.4 mph) , snow, rain, smog, heavy wind, hail,

lightning, tornadoes or hurricanes.

2. Keep the aircraft at least 10 meters (30 feet) away from obstacles, people,

animals, buildings, public infrastructure, trees, and bodies of water when in

ight. As the aircraft’s altitude increases, keep an even further distance away

from the aforementioned objects or obstacles.

3. Be EXTRA cautious when operating the aircraft indoors. Some features of the

aircraft, especially the stabilization feature, may be impacted.

4. DO NOT operate the aircraft where there is obvious change in the ground

level (e.g. ight from inside the building to outside) and when the GPS signal

is weak, in case the positioning function is interfered and thus impacts ight

safety.

1. Aircraft and battery performance is subject to environmental factors such as air

density and temperature.

a. Be very careful when ying 13,123 feet (4,000 m) or more above sea level

since battery and aircraft performance may be reduced.

2. DO NOT use the aircraft near accidents, fire, explosions, floods, tsunamis,

avalanches, landslides, earthquakes, dust, or sandstorms.

Interference with Communications

1. Fly in open areas. Tall buildings, steel structures, mountains, rocks or even trees

may affect the accuracy of the on-board compass and block the GPS signal.

2. DO NOT y near areas with magnetic or radio interference. These include but are

NOT limited to: Wi-Fi hotspot, router, Bluetooth device, high voltage lines, large

scale power transmission stations or mobile base stations and broadcasting

towers. Failing to do so may compromise the transmission quality of this product

or cause remote control device and video transmission errors which may affect

ight orientation and location accuracy. The aircraft may behave abnormally or

go out of control in areas with too much interference.

Operating the Aircraft Responsibly

To avoid serious injury and property damage, observe the following rules:

1. Make sure you are NOT under the inuence of anesthesia, alcohol, drugs or

suffering from dizziness, fatigue, nausea or any other conditions, whether

physical or mental, that could impair your ability to operate the aircraft safely.

2. Pulling the left and right stick to the bottom inside corner at the same time

will stop the motor when the aircraft is airborne. The landing function of the

aircraft will not be triggered. DO NOT perform the aforementioned combination

command unless in an emergency situation.

3. Upon landing, power off the aircraft rst, then switch off the remote control

device.

4. DO NOT drop, launch, re or otherwise project any dangerous payloads on or

at any buildings, persons or animals, or which could cause personal injury or

property damage.

5. DO NOT use the aircraft that has been crashed or accidently hit, or the aircraft

that is not in good condition.

1. Make sure you have been sufciently trained and have contingency plans for

emergency situations or for when accidents occur.

2. Make sure you have a ight plan and never y the aircraft recklessly.

3. Respect the privacy of others when using the camera. Make sure you comply

with local privacy laws, regulations, and moral standards.

4. DO NOT use this product for any reason other than general personal use. DO

NOT use it for any illegal or inappropriate purpose (such as spying, military

operations, or unauthorized investigations).

5. DO NOT use this product to defame, abuse, harass, stalk, threaten or otherwise

violate the legal rights (such as the right of privacy and publicity) of others.

6. DO NOT trespass onto private property of others.

Flight Modes, Functions and Warnings

Flight Modes

The aircraft will y in P-mode by default, and the ight mode will switch to A-mode

automatically if P-mode is unavailable. When flying in A-mode, take EXTRA

precautions because some features are NOT available in A-mode.

1. P-mode (Positioning): P-mode works best when the GPS signal is strong. The

aircraft utilizes the GPS and Vision System to automatically stabilize itself,

navigate between obstacles or track a moving object. Advanced features such

as TapFly and ActiveTrack are enabled in this mode.

2. A-mode (Attitude): When neither the GPS nor the Vision System is available, the

aircraft will only use its barometer for positioning to control the altitude.

3. S-mode (Sports): Only can be enabled by remote controller, S-mode is identical

to P-mode in terms of ight controller settings, except that the handling gain

values of the aircraft are adjusted in order to enhance the maneuverability of the

aircraft. The maximum ight speed of the aircraft is increased in this mode.

If you intend to switch to modes that disable GPS assistance (e.g., Atti mode),

you are required to accept the prompted disclaimer to enable this function. If

this function is enabled, you further understand and agree that data including

but not limited to function records could be uploaded to and maintained on a DJI

designated server.

The aircraft will revert to A-mode when GPS signal is weak, or when the compass

experiences interference where the Vision System is unavailable. In A-mode, the

aircraft is easily affected by its surroundings, which may result in horizontal shifting.

In A-mode, the Vision System and some advanced features are disabled. Therefore,

the aircraft cannot position or auto-brake in this mode. Please land in a safe place

as soon as possible to avoid hazards. Avoid ying in areas where GPS signal is

weak, or in conned spaces. The aircraft will otherwise be forced to enter A-mode,

leading to a potential ight hazard.

Return-to-Home

1. The Return-to-Home feature will NOT work if the GPS signal is insufcient or if

GPS is not active.

2. Obstacles may adversely affect the Return-to-Home function. Please adjust the

aircraft location, altitude and speed while returning home to avoid obstacles.

3. Make sure to always operate the aircraft within the transmission range of the

remote control device.

4. Only use the Failsafe and Return-to-Home functions in emergency cases. Such

functions may be affected by the weather, the environment, or any nearby

magnetic elds.

5. The aircraft can only avoid obstacles in close range (within 100m from the Home

Point) during the RTH process. The obstacle avoidance function is disabled

when lighting conditions are not ideal or when the Vision System is otherwise

disabled. DO NOT rely on the 3D Sensing System. The pilot’s sound discretion

is required during the ight. You can use the remote control device to control the

aircraft to avoid obstacles or to cancel the RTH process.

Low Battery

1. When the Critical Battery Level Warning activates and the aircraft is descending

automatically, you may push the throttle up to maintain the aircraft's altitude and

navigate it to a more appropriate location for landing.

2. When battery warnings are triggered, promptly bring the aircraft back to the

Home Point or land the aircraft to avoid losing power during ight and causing

damage to the aircraft, property, animals, and people.

Vision System and 3D Sensing System

1. The Vision System cannot work properly over surfaces that do NOT have clear

pattern variations. The Vision System is only effective when the aircraft is at

altitudes of 0.3 to 30 meters. If the aircraft is above the Attitude Range (8 meters),

the Vision Positioning function may be affected, y with caution.

2. The Vision System may NOT function properly when the aircraft is ying over

water or snow-covered areas.

3. Note that the Vision System may NOT function properly when the aircraft is ying

too fast or too low.

4. Operate the aircraft cautiously when in any of the following situations:

a. Flying over monochrome surfaces (e.g., pure black, pure white, pure red, pure

green).

b. Flying over highly reective surfaces;

c. Flying at high speeds (over 10m/s (32.8 feet/s) at 2 meters (6.6 feet) or over 5m/

s (16.4 feet) at 1 meter (3.3 feet);

d. Flying over water or transparent surfaces;

e. Flying over moving surfaces or objects;

f. Flying in an area where the lighting changes frequently or drastically;

g. Flying over extremely dark (< 10 lux) or bright (> 10,000 lux) surfaces;

h. Flying over surfaces that strongly reect or absorb infrared waves (e.g. mirror);

i. Flying over surfaces without clear patterns or texture;

j. Flying over surfaces with identical repeating patterns or textures (e.g. tiles with

same design);

k. Flying over obstacles with surfaces that are too small to reect infrared waves.

5. Keep the sensors clean at all times. DO NOT temper with the sensors.

6. The Vision System may not be able to recognize patterns on the ground in low

light conditions (less than 100 lux).

7. The Vision System and 3D Sensing System are not able to brake and stop the aircraft

at a safe distance from an obstacle if the aircraft speed exceeds 3.5 m/s (7.8 mph).

TapFly

To prevent serious injury or property damage, observe the following guidelines:

1. DO NOT instruct the aircraft to fly towards people, animals, small and fine

objects (e.g. tree branches and power lines) or transparent objects (e.g. glass

and water).

2. Watch out for potential obstacles in your surrounding area (especially on the rear,

left, and right sides of the aircraft) and stay clear of them to avoid accidents.

3. Be prepared to take control of the aircraft by pressing the STOP button on the

screen to exit TapFly in case of an emergency.

1. There may be deviations between the expected and actual paths for your TapFly

selection.

2. The selectable range on the screen is limited. You cannot make TapFly selections

near the upper or lower edges of the screen.

3. The TapFly mode may NOT function properly when the aircraft is flying over

water or snow-covered areas.

ActiveTrack

To prevent serious injury and property damage, observe the following guidelines:

1. Ensure there are no people, animals, small and ne objects (e.g. tree branches

and power lines) or transparent objects (e.g. glass and water) along the desired

tracking path.

2. Watch out for potential obstacles in your surrounding area (especially on the rear,

left, and right sides of the aircraft) and stay clear of them to avoid accidents.

3. Be prepared to take control of the aircraft by pressing the STOP button on the

screen to exit ActiveTrack in case of an emergency.

4. Ensure there are no obstacles behind the aircraft when it performs ActiveTrack in

the reverse or lateral direction.

1. Be extra cautious when using ActiveTrack in any of the following situations:

a. The movement of the tracked subject is not on a level plane;

b. The tracked subject changes shape drastically while moving;

c. The tracked subject could be blocked or out of sight for a long time;

d. When the tracked object is in a snow-covered area;

e. The lighting is extremely low (< 300 lux) or high (> 10,000 lux);

f . The tracked subject has a similar color or pattern as the surrounding

environment.

2. You must follow local privacy laws and regulations when using ActiveTrack.

Gesture Control

1. Ensure to hold the aircraft when take-off or landing in a windless environment,

avoiding the aircraft from approaching human or other obstacles, and always

keep your ngers lower than the propeller’s rotation radius.

2. Always keep away from propellers. Be sure to use the Propeller Guard during

ight.

3. Keep your body at least 50 cm away from from any walls or pillars so that the

sensor can recognize the gesture correctly.

4. When using the gesture to control the aircraft, make sure that your hands are not

moving too fast and there is no human, animals or other obstacles on the ight path.

5. Always pay attention on the aircraft to make sure it follows the movement of your

hands. Put your hands down or close to the chest quickly to exit gesture control

in case of emergency.

1. Be extra cautious when using gesture control in any of the following situations:

a. The lighting is extremely low (< 300 lux) or high (> 10,000 lux);

b. In crowded places;

c. When the wind speed exceeds beaufort scale 3;

d. Places where they are too many items or objects nearby or there are obvious

height differences (e.g. ofces, dwellings, balconies or cliffs);

e. When the aircraft is in low battery level.

QuickShot

1. Please use this function at locations that are clear of buildings and other obstacles.

Make sure that there is no human, animals or other obstacles on the ight path.

2. Always pay attention to objects around the aircraft and use the remote control

device to avoid accidents (such as collisions) or occlusion with the aircraft.

1. Be extra cautious when using QuickShot in any of the following situations:

a. When the shoot subject is blocked for a long time or outside the line of sight;

b. When the shoot subject is more than 50 m away from the aircraft;

c. When the shoot subject is similar in color or patterns with the surrounding;

d. When the shoot subject is in the air;

e. When the shoot subject moves fast;

f. The lighting is extremely low (< 300 lux) or high (> 10,000 lux).

2. DO NOT use QuickShot in places that are close to buildings or the GPS signal is

weak, to avoid unstable ight path.

3. You must follow local privacy laws and regulations when using QuickShot.

Compliance with Regulations & No Fly Zones

Regulations

To avoid serious injury and property damage, observe the following rules:

1. DO NOT operate in the vicinity of manned aircraft, regardless of altitude. (Land

immediately if necessary)

2. DO NOT y the aircraft in densely populated areas, including cities, sporting

events, exhibitions, performances, etc.

3. DO NOT y the aircraft above the authorized altitude. Remain well clear of

and DO NOT interfere with manned aircraft operations. Be aware of and avoid

other aircrafts and obstacles at all times.

To avoid serious injury and property damage, observe the following rules:

1. DO NOT y the aircraft near or inside no y zones specied by local laws and

regulations. The no y zone list includes: airports, borders between two sovereign

countries or regions, major cities/regions, etc., and is continuously updated. DO

NOT y around sensitive infrastructure or property such as power stations, water

treatment facilities, correctional facilities, heavily traveled roadways, government

facilities, military zones, etc.

2. DO NOT y the aircraft above the authorized altitude

3. ALWAYS keep your aircraft within visual line of sight (VLOS), and use an observer

to assist if needed.

4. NEVER use the aircraft to carry illegal or dangerous goods/payloads.

1. Make sure you understand the nature/type of your flight operation (such

as for recreation, for public use, or for commercial use) and have obtained

corresponding approval and clearance from the related government agencies

before ight. Consult with your local regulators for comprehensive denitions

and specic requirements. For users operating their aircraft in the United States,

please rst visit http://www.knowbeforeyouy.org/ and take the most appropriate

action that suits your circumstances.

2. Please note that remote-controlled aircraft may be banned from conducting

commercial activities in certain countries and regions. Check and follow all local

laws and ordinances before ying as those rules may differ from those stated here.

3. Respect the privacy of others when using the camera. DO NOT conduct

surveillance operations such as image capture or video recording on any person,

entity, event, performance, exhibition, and property without authorization or

where there is an expectation of privacy, even if the image or video is captured

for personal use.

4. Please be advised that in certain areas, the recording of images and videos

from events, performances, exhibitions, or commercial properties by means of

a camera may contravene copyright or other legal rights, even if the image or

video is shot for personal use.

No Fly Zones

You shall be solely responsible for all your behaviors when ying with DJI

aircraft.

DJI takes ight safety seriously, and has therefore developed various aids

to help users comply with local rules and regulations while ying.

However, the

aids are not able to help you avoid penalty or punishment if you violate local

laws or regulations.

We strongly recommend that you update the rmware to the

latest version to ensure the following features are fully updated:

No Fly Zones

1. No Fly Zones include but are not limited to major airports around world, borders

between two sovereign countries or regions, major cities/regions, etc.

2. The relevant information of No Fly Zones is listed on the ofcial DJI website at

http://www.dji.com/ysafe/no-y and is subject to periodic updates in line with the

latest regulatory requirements without prior notice.

3. Some No Fly Zones are comprised of several zones. Each zone features circles

of various sizes. The aircraft will NOT be able to take off in the inner most zone of

the No Fly Zone, and will descend to the specied altitude when it approaches

the edge of the inner most zone. Ground station functionality is disabled when

the aircraft is within a No Fly Zone.

4. Users are NOT able to set up waypoints within No Fly Zones.

Altitude Limit

1. Fly NO higher than 120 meters (400 feet) above ground level and stay away from

any surrounding obstacles.

2. If you intend to fly above the default altitude limit, you are required to accept

the prompted disclaimer to enable the new altitude limit. If a new altitude limit is

set, you further understand and agree that data including but not limited to ight

telemetry data and altitude limit changes could be uploaded to and maintained on

a DJI-designated server.

Compliance Information

FCC Compliance Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the FCC

radio frequency exposure limits, human proximity to the antenna shall not be less

than 20cm during normal operation.

IC RSS Warning

This device complies with Industry Canada licence-exempt RSS standard (s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le fonctionnement.

IC Radiation Exposure Statement:

This equipment complies with IC RF radiation exposure limits set forth for an

uncontrolled environment. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

This equipment should be installed and operated with minimum distance 20cm

between the radiator& your body.

Any Changes or modications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

KCC Warning Message

“해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는

할 수 없습니다 .”

“해당 무선설비는 운용 중 전파혼신 가능성이 있음”

La pagina sta caricando ...

dji GO 4 Guida utente

Marca: dji

Modello: GO 4

Tipo: Guida utente

Scarica il pdf

rapporto

in altre lingue

English: dji GO 4 User guide

dji GO 4 Guida utente

dji GO 4 Guida utente

in altre lingue

Documenti correlati