PHANTOM 3
SAFETY GUIDELINES
AND DISCLAIMER
2017.06V1.4
©
2017 DJI. All Rights Reserved.
3
Contents
Safety At a Glance
4
NOTICE
6
Glossary
6
Pre-ight Checklist
6
Disclaimer and Warning
7
Before You Begin
8
Individual Parts
8
Regarding Genuine and Functional Parts 8
Remote Controller 8
Camera 9
Gimbal 9
Compass 9
Propulsion Systems 10
App 11
Firmware 11
Product Care
12
Storage and Transportation 12
Maintenance and Upkeep 12
Flight Condition Requirements
13
Weather Conditions and Surrounding Environment 13
Interference with Flight Controller, Communications, and Positioning Systems 13
Operating the Aircraft Responsibly 13
Flight Modes, Functions and Warnings
14
Flight Modes 14
Failsafe and Return-to-Home 15
Low Battery 15
Vision Positioning System 15
Compliance with Regulations & No Fly Zones
16
Regulations 16
No Fly Zones 17
Compliance Information
18
4
©
2017 DJI. All Rights Reserved.
Safety At a Glance
1. Environmental Considerations
• Always y at locations that are clear of building and other
obstacles.
• DO NOT y above or near large crowds.
• Avoid ying at altitudes above 400 feet (120 m).
• Be very careful when ying 19,600 feet (6,000 m) or more
above sea level.
• Fly in moderate weather conditions with temperatures between
32° to 104° F (0° to 40° C).
2. Pre-ight Checklist
• Ensure the remote controller and aircraft batteries are fully charged.
• Ensure the propellers are in good condition and securely tightened.
• Ensure there is nothing obstructing the motors.
• Be sure to calibrate the compass at every new ight location or if the app prompts you.
• Check that the camera lens is clean and free of stains.
3. Operation
• Stay away from the rotating propellers and motors.
• Maintain line of sight of your aircraft at all times
• DO NOT perform the Combination Stick Command when the aircraft is airborne.
• DO NOT answer incoming calls during ight.
• DO NOT y under the inuence of alcohols or drugs.
• During the Return-to-Home procedure, you can adjust the altitude to avoid obstacles.
• DO NOT y closely above reective surfaces such as water or snow, as these terrain may affect
the performance of the Vision Positioning System.
• In the instance of a Low Battery Warning, land the aircraft at a safe location.
• After landing, rst turn off the Intelligent Flight Battery, then turn off the remote controller.
4. Maintenance and Upkeep
• DO NOT use aged, chipped or broken propellers.
• Recommended storage temperature: between 71° and 82° F (22° and 28° C).
• Refer to the
Phantom 3 Intelligent Flight Battery Safety Guidelines
for more information about the
safe use of the battery.
5. Observe Local Laws and Regulations
• DO NOT y in the No Fly Zones. You can nd a complete list of these areas at http://ysafe.dji.com/
• The DJI No Fly Zone is not a replacement for local government regulations or good judgment.
• Avoid ying in areas where rescue teams are actively using the airspace.
The Phantom 3 is
NOT a toy and is not
suitable for children
under the age of 18.
Note that ‘Safety at a Glance’ only
provides a quick overview of the
safety tips. Make sure you read
and understand the remaining
sections of the Phantom 3 Safety
Guidelines and Disclaimer.
©
2017 DJI. All Rights Reserved.
5
Fly in Open Areas Calibrate the Compass Maintain Line of Sight Fly Below
400 feet (120 m)
Avoid ying over or near obstacles, crowds, high voltage power lines, trees or bodies of water.
DO NOT y near strong electromagnetic sources such as power lines and base stations as it may affect the onboard
compass.
≥
10m/s
DO NOT use the aircraft in adverse weather conditions such as rain, snow, fog and
wind speeds exceeding 10 m/s or 22 mph.
Stay away from the rotating
propellers and motors.
No Fly
Zone
Learn more at:
http://ysafe.dji.com/no-y
6
©
2017 DJI. All Rights Reserved.
NOTICE
All instructions and other collateral documents are subject to change at the sole discretion of SZ DJI
TECHNOLOGY CO., LTD. For up-to-date product information, visit http://www.dji.com and click on the
Phantom 3 product page.
Glossary
The following terms are used throughout the product literature to indicate various levels of potential harm
when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property
damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property
damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage,
collateral damage, and serious injury OR create a high probability of supercial injury.
Read the ENTIRE user manual to become familiar with the features of
this product before operating. Failure to operate the product correctly
can result in damage to the product or personal property and cause serious injury.
This is a sophisticated product. It must be operated with caution and common sense and
requires some basic mechanical ability. Failure to operate this product in a safe and responsible
manner could result in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. DO NOT use with incompatible
components or alter this product in any way outside of the documents provided by SZ DJI
TECHNOLOGY CO., LTD. These Safety Guidelines contain instructions for safety, operation and
maintenance. It is essential to read and follow all of the instructions and warnings in the user
manual, prior to assembly, setup or use, in order to operate the product correctly and avoid
damage or serious injury.
Age Recommendation: Not for children under the age of 18. This is not a toy.
Pre-ight Checklist
1) Ensure that you are using only genuine parts and that all parts are in mint condition.
2) Ensure the remote controller, Intelligent Flight Battery, and mobile device are fully charged.
3) Ensure that there is no foreign object stuck to the camera lens, the Micro SD card has been inserted into
the camera, and the gimbal can rotate freely before powering it on.
4) Ensure the propellers are securely mounted onto the motors, and the motors can start and function normally.
5) Follow the on-screen instructions to calibrate the compass.
6) Ensure the app and aircraft's rmware have been upgraded to the latest version.
7) Ensure that your flight area is outside the No Fly Zones and flight conditions are suitable for flying the
aircraft.
8) Be sure that you are NOT ying under the inuence of alcohol, drugs or any substance that may impair
your cognitive abilities.
9) Be familiar with the selected ight mode and understand all safety functions and warnings.
10) Be sure to observe all local regulations, obtain appropriate authorizations, and understand the risks.
REMEMBER: It is solely your responsibility to comply with all ight regulations.
11) Ensure the DJI GO app is properly launched to assist your operation of the aircraft. Without the ight
data recorded by the DJI GO app, in certain situations (including the loss of your aircraft) DJI may not
be able to provide aftersales support to you or assume liability.
©
2017 DJI. All Rights Reserved.
7
Disclaimer and Warning
This product is NOT a toy and is not suitable for children under the age of 18. Adults should keep the Phantom
3 out of the reach of children and exercise caution when operating this aircraft in the presence of children.
This product is a ying camera that offers easy ight when in good working order as set forth below. Visit
http://www.dji.com for the most current instructions and warnings and http://knowbeforeyouy.org/ for more
information about ight safety and compliance.
The information in this document affects your safety and your legal rights and responsibilities. Read this entire
document carefully to ensure proper conguration before use. Failure to read and follow the instructions and
warnings in this document may result in product loss, serious injury to you, or damage to your aircraft.
By using this product, you hereby signify that you have read this disclaimer carefully and that you
understand and agree to abide by the terms and conditions herein. You agree that you are solely
responsible for your own conduct while using this product, and for any consequences thereof. You agree
to use this product only for purposes that are proper and in accordance with all applicable laws, rules, and
regulations, including international and domestic airspace regulations, and all terms, precautions, practices,
policies and guidelines DJI has made and may make available.
DJI accepts no liability for damage, injury or any legal responsibility incurred directly or indirectly from the
use of this product. The user shall observe safe and lawful practices including, but not limited to, those set
forth in these Safety Guidelines.
Data Storage and Usage
When you use our mobile app or our products or other software, data regarding the use and operation of
the product, such as ight telemetry data (e.g., speed, altitude, battery life, and information about the gimbal
and camera) and operations records, may be automatically or manually uploaded to and maintained on
a DJI-designated server. The internal storage device incorporated into the product stores various types of
data, including ight telemetry data. You may also provide ight telemetry data and other data to us when
you manually transmit that information from the internal storage device to us.
The information that is automatically uploaded or manually uploaded to us does not include personal data
(i.e., your name, address, email, or other information that specically identies you), but personal data, such
as your user name, may become associated with, used to identify, or tagged to such uploaded information
when we store it. We separately describe how we use your user name and other personal data on our
privacy policy at http://www.dji.com/policy. By using the product, the mobile app or other software we
distribute, or by manually providing data to us, you consent to the following:
• Our storage of any flight telemetry data and other data uploaded or provided to us, including in
combination with your user name;
• Our use of any such data uploaded or provided (including your user name) in connection providing
support and services to you and to improve our products;
• Our disclosure of such data uploaded or provided (including your user name) to our agents and/or
contractors who may use it on our behalf or in connection with their relationship with us; and
• Our disclosure of such uploaded or provided data (including your user name) as required by law, in a
matter of public safety or policy, as needed in connection with the transfer of our business assets, or if we
believe in good faith that sharing the data is necessary to protect our rights or property.
DJI reserves the right to update this disclaimer and the Safety Guidelines. Please visit www.dji.com and check your email
periodically for the latest version. This disclaimer is made in various language versions; in the event of divergence among
different versions, the English version shall prevail.
8
©
2017 DJI. All Rights Reserved.
Before You Begin
The following documents have been produced to help you safely operate and make full use of your
Phantom 3:
In the Box
Safety Guidelines and Disclaimer
Intelligent Flight Battery Safety Guidelines
Quick Start Guide
User Manual
Check all of the included parts listed in the
Phantom 3 In the Box
document and read the
Phantom 3 Safety
Guidelines
before ight. Then prepare for your rst ight by using the
Phantom 3 Quick Start Guide
and
watching all of the tutorial videos on DJI’s ofcial website (http://www.dji.com). If you have questions, refer
to the
Phantom 3 User Manual
in the app or on DJI’s ofcial website for more comprehensive information.
Make sure you fully understand the functionality of each individual part, the ight condition requirements, the
key contingency warning functions/systems, and all government regulations before each ight. If you have
any questions or problems during the assembly, maintenance or use of this product, please contact DJI or
a DJI authorized dealer.
Individual Parts
Regarding Genuine and Functional Parts
To avoid component malfunction, serious injury, and property damage, observe the following rules:
1)
Use only genuine DJI parts or parts certified by DJI. Unauthorized parts or parts from non-DJI
certied manufacturers may cause system malfunctions and compromise safety.
2)
Ensure there are no foreign objects (such as water, oil, soil, sand, etc.) inside of the aircraft or its
components.
3)
Ensure the aircraft and its components – including but not limited to the remote controller, camera,
gimbal, compass, propulsion system, and battery – are all in good working order, damage-free,
and functioning well. Refer to the remaining sections in this document for more details on how to
ensure the functionality of these components.
Remote Controller
1) Ensure the remote controller is fully charged before each ight.
2) If the remote controller is powered on and has NOT been used for 5 minutes, it will sound an alert. After 10
minutes it will automatically power off. Move the sticks or perform some other action to cancel the alert.
3) Adjust the clamp of the mobile device holder to allow a rm grip on your mobile device.
4) Ensure the mobile device holder is rmly in place and does not slip.
5) Ensure the antennas of the remote controller are unfolded and adjusted to the proper position to achieve
optimal transmission quality.
6) Repair or replace the remote controller if damaged. A damaged remote controller antenna will greatly
©
2017 DJI. All Rights Reserved.
9
decrease performance.
7) Linking is required if you wish to replace your remote controller or receiver or add a new remote controller.
Refer to the User Manual for details.
Camera
To avoid possible serious injury and property damage, observe the following rule:
1) DO NOT block any ventilation holes on the camera as the heat generated may hurt you and damage the
device.
1) Check camera settings before use to make sure you can adjust them to t your needs.
2) Test the camera by shooting a few test images and check that it is operating correctly before shooting
important pictures or videos.
3) DO NOT remove the Micro SD card from the camera when it is powered on.
4) Photos or videos cannot be transmitted or copied from the camera if the Intelligent Flight Battery is
powered off.
5) Be sure to power off the Intelligent Flight Battery correctly, otherwise your camera parameters will NOT
be saved and any recorded videos may be damaged. NOTE: Regardless of the reason, DJI will not be
responsible for any failure of an image or video to be recorded or having been recorded in a way that is
not machine readable.
Gimbal
1) Precision elements in the gimbal may be damaged in a collision or impact, which may cause the gimbal
to function abnormally.
2) DO NOT apply external force to the gimbal after the gimbal is powered on.
3) DO NOT add any payloads to the gimbal, as this may cause the gimbal to function abnormally or even
lead to motor damage.
4) Remove the gimbal clamp before powering on the gimbal. Re-install the gimbal clamp to secure the
gimbal’s position if you are going to store the aircraft for an extended period.
Compass
To avoid possible serious injury and property damage, observe the following rule:
1) Land immediately when severe drifting occurs in ight, i.e., the aircraft does NOT y in straight lines.
1) Ensure the compass is calibrated before every flight. Failure to calibrate may lead to poor flight
performance or a crash.
2) DO NOT attempt to calibrate your compass where there is a chance of strong magnetic interference.
10
©
2017 DJI. All Rights Reserved.
This includes areas where there are massive metal objects, parking structures, steel reinforcements
underground, or under bridges.
3) DO NOT carry ferromagnetic materials with you during calibration, such as keys or mobile phones.
4) The compass should always be calibrated when moving from indoor spaces to outdoor spaces.
5) If the rear LEDs show a solid red light, compass calibration has failed. Please recalibrate.
6) After successful calibration, the compass may become abnormal when you place the aircraft on the
ground. This may be because of underground magnetic interference. Move the aircraft to another location
and try again.
7) When to recalibrate
a) When compass data is abnormal, and the Aircraft Status Indicator is blinking red and yellow.
b) When ying in a new location, or a location that is different from your last ight.
c) When the mechanical structure of the aircraft has changed, i.e. new mounting position of the compass.
d) When severe drifting occurs in ight, i.e. the aircraft does NOT y in straight lines.
Propulsion Systems
To avoid serious injury to yourself or others, which may be caused by the rotating propellers and
motors, observe the following rules:
Propellers
1)
DO NOT use aged, chipped, or broken propellers.
2)
Always power off the aircraft before touching the propellers.
3)
Be aware of the sharp edges of the propellers when mounting or removing the propellers. Wear
gloves or take other protective measures when touching the propellers.
4)
Whenever necessary, use tools (e.g., wrench, screwdriver, pliers, etc.) to remove or install the
propellers.
5)
Ensure the propellers are securely mounted to prevent them from falling off the motors.
6)
DO NOT turn on the motors when propellers are mounted and there are other people or animals in
the immediate vicinity.
Motors
1)
Ensure the motors are securely mounted and rotating smoothly.
2)
DO NOT attempt to modify the structure of the motors.
3)
DO NOT touch or let your hands or body come in contact with the motors after ight as they may
be hot.
To avoid possible serious injury and property damage, observe the following rules
:
1) DO NOT block any of the ventilation holes on the motors.
2) DO NOT block any of the ventilation holes on the frame arm of the aircraft.
Motors
1) Keep the motors free of dust.
2) If a motor is stuck and unable to rotate freely, execute the CSC (Combination Stick Command) to stop the
motors immediately.
©
2017 DJI. All Rights Reserved.
11
Electronic Speed Controllers
1) Ensure the ESCs sound a normal tune when powered on.
App
1) Be sure to fully charge your tablet or mobile device before launching the app. A tablet is recommended
for a better user experience.
2) If you are using a phone as your mobile display device, be sure to continue ying safely when the phone
receives an incoming call. DO NOT accept phone calls during ight.
3) Read all prompted safety tips, warning messages, and disclaimers carefully. Be familiar with the related
regulations in your area. You are solely responsible for being aware of all relevant regulations and ying in
a way that is compliant.
a) Read and understand the warning messages before using the Auto-take off and Auto-landing features.
b) Read and understand the warning message and disclaimer before setting the altitude beyond the
default limit.
c) Read and understand the warning messages and disclaimer before switching between ight modes.
4) Land your aircraft immediately if there is an alert shown on the app.
5) Examine and check all warning messages on the checklist displayed in the app prior to each ight.
6) Use the in-app simulator to practice your ight skills if you have never operated the aircraft or if you do not
have sufcient experience to be comfortable operating the aircraft.
7) Beginner Mode is enabled by default when you launch the app for the rst time. The aircraft’s altitude and
ight distance is restricted when ying in Beginner Mode. We recommend you y in Beginner Mode to
perfect your ight skills. Operate the actual aircraft only after you are condent that you have mastered
adequate ight skills.
8) Cache the map data of the area where you intend to y the aircraft by connecting to the Internet before
each ight.
Firmware
To avoid serious injury to children and animals, observe the following rule:
1)
Keep children and animals at a safe distance during any rmware upgrade, system calibration, and
parameter setting procedures.
1) For safety, always update the rmware to the latest version when an upgrade notication is shown in the
app.
2) Firmware upgrade notifications will prompt you to proceed with an update immediately or to update
the rmware within three days. If you choose to ignore the current rmware update, you are required
to accept the prompted disclaimer. You further understand and agree that the data including but not
limited to ight telemetry data and user selection records may be uploaded to and maintained on a DJI-
designated server.
3) Be sure to download the rmware package le from the ofcial DJI website. Verify the rmware package
le’s integrity before upgrading.
4) Be sure to update the remote controller’s firmware to the latest version after you update the aircraft’s
12
©
2017 DJI. All Rights Reserved.
rmware.
5) The remote controller may become unlinked from the aircraft after updating. Re-link the remote controller
and aircraft.
6) Be sure to check all connections and remove the propellers from the motors before performing the
rmware update.
7) Ensure there is only one rmware package le stored on your SD card.
8) Only storage devices that are formatted for FAT32 and exFAT le systems are supported for aircraft and
remote controller rmware updates.
9) Delete any automatically generated
.txt
les on the SD card when updating multiple remote controllers.
Product Care
Storage and Transportation
To avoid serious injury to children and animals, observe the following rule:
1)
Small parts, such as cables and straps, are dangerous if swallowed. Keep all parts out of reach of
children and animals.
1) Store the Intelligent Flight Battery and remote controller in a cool, dry place away from direct sunlight
to ensure the built-in LiPo battery does NOT overheat. Recommended storage temperature: between
71° and 82° F (22° and 28° C) for storage periods of more than three months. Never store in environments
outside the temperature range of -68° to 113° F (-20° to 45° C).
2) DO NOT allow the camera to come into contact with, or become immersed in, water or other liquids. If it
gets wet, wipe dry with a soft, absorbent cloth. Turning on an aircraft that has fallen into water may cause
permanent component damage. DO NOT use substances containing alcohol, benzene, thinners or other
ammable substances to clean or maintain the camera. DO NOT store the camera in humid or dusty
areas.
3) DO NOT connect this product to any USB interface that is older than version 2.0. DO NOT connect this
product to any "power USB" or similar devices.
Maintenance and Upkeep
1) Check every part of the aircraft after any crash or violent impact. If you have any problems or questions,
please contact a DJI authorized dealer.
2) Regularly check the Battery Level Indicators to see the current battery level and overall battery life. When
the battery life reaches 0%, it can no longer be used.
©
2017 DJI. All Rights Reserved.
13
Flight Condition Requirements
Weather Conditions and Surrounding Environment
The aircraft is designed to operate in good to moderate weather conditions. To avoid collision, serious
injury and property damage, observe the following rules:
1)
DO NOT use the aircraft in severe weather conditions. These include wind speeds exceeding 10 m/s,
snow, rain, smog, heavy wind, hail, lightning, tornadoes or hurricanes.
2)
Keep the aircraft at least 10 meters (30 feet) away from obstacles, people, animals, buildings, public
infrastructure, trees, and bodies of water when in ight. Stay even further away from the above
objects as your altitude increases.
3)
Be EXTRA cautious when operating the aircraft indoors.
1) Aircraft and battery performance is subject to environmental factors such as air density and temperature.
a) Be very careful when ying 20,000 feet (6,000 meters) or more above sea level as battery and aircraft
performance may be reduced.
b) It is not recommend to operate the aircraft store in environments outside the temperature range of
-68° to 113° F (-20° to 45° C).
2) DO NOT use the aircraft near accidents, fire, explosions, floods, tsunamis, avalanches, landslides,
earthquakes, dust, or sandstorms.
Interference with Flight Controller, Communications, and Positioning Systems
1) Fly in open areas. Tall buildings or steel structures may affect the accuracy of the on-board compass and
block the GPS signal.
2) Avoid interference between the remote controller and other wireless equipment. Make sure to turn off the
Wi-Fi on your mobile device.
3) DO NOT y near areas with magnetic or radio interference. These include but are NOT limited to: high
voltage lines, large scale power transmission stations or mobile base stations and broadcasting towers.
Failing to do so may compromise the transmission quality of this product or cause remote controller and
video transmission errors which may affect flight orientation and location accuracy. The aircraft may
behave abnormally or go out of control in areas with too much interference.
Operating the Aircraft Responsibly
To avoid serious injury and property damage, observe the following rules:
1)
Make sure you are NOT drunk, taking drugs, under the inuence of anesthesia, or suffering from
dizziness, fatigue, nausea or any other conditions, whether physical or mental, that could impair
your ability to operate the aircraft safely.
14
©
2017 DJI. All Rights Reserved.
2)
DO NOT perform the Combination Stick Commands when aircraft is airborne, or else the motors
will stop.
3)
Upon landing, power off the aircraft rst, then switch off the remote controller.
4)
DO NOT drop, launch, re or otherwise project any dangerous payloads on or at any buildings,
persons or animals, or which could cause personal injury or property damage.
1) Make sure you have been sufficiently trained and are fully aware of any contingency plans before
accidents happen.
2) Make sure you have a ight plan and never y the aircraft recklessly.
3) Respect the privacy of others when using the camera. Make sure you comply with local privacy laws,
regulations, and moral standards.
4) DO NOT use this product for any reason other than general personal use. DO NOT use it for any illegal or
inappropriate purpose (such as spying, military operations, or unauthorized investigations).
5) DO NOT use this product to defame, abuse, harass, stalk, threaten or otherwise violate the legal rights (such
as the right of privacy and publicity) of others.
6) DO NOT trespass into private property of others.
Flight Modes, Functions and Warnings
Flight Modes
To avoid serious injury and property damage, observe the following rule:
1)
DO NOT switch from P-mode to either Atti mode or F-mode unless you are sufciently familiar with
the aircraft’s behavior for each ight mode, since disabling GPS may result in being unable to land
the aircraft safely.
P-mode is preferred for most ying scenarios. Users can switch to Atti mode where and when P-mode is
unavailable. Be aware that some features are NOT available for Atti mode, and therefore be EXTRA cautious
when ying in Atti mode.
1) P-mode (Positioning): P-mode works best when the GPS signal is strong. There are three different states
of P-mode, which will be automatically selected by the Phantom 3 depending on GPS signal strength and
Vision Positioning sensors:
a) P-GPS: GPS and Vision Positioning are both available, and the aircraft is using GPS for positioning.
b) P-OPTI*: If GPS is NOT available, the aircraft will use the Vision Positioning System to hover accurately.
Note that the Vision Positioning System may NOT work properly when the Phantom 3 is ying over
water, over surfaces without a clear pattern, or in a low light environment.
c) P-ATTI: When neither GPS nor Vision Positioning is available, the aircraft is using only its barometer for
positioning, so only altitude is controlled.
Note:*Only applicable to models with the Vision Positioning System.
2) Atti mode (Attitude): The GPS and Vision Positioning System are NOT used for positioning. The aircraft
©
2017 DJI. All Rights Reserved.
15
only uses its barometer to maintain altitude. If it is still receiving a GPS signal, the aircraft can automatically
return home if the Remote Controller signal is lost and if the Home Point has been recorded successfully.
3) F-mode (Function): Intelligent Orientation Control (IOC) is activated in this mode. Ensure you are familiar
with IOC functions before use.
If you intend to switch to modes that disable GPS assistance (e.g., Atti mode), you are required to accept
the prompted disclaimer to enable this function. If this function is enabled, you further understand and agree
that data including but not limited to ight telemetry data and function records could be uploaded to and
maintained on a DJI designated server.
Failsafe and Return-to-Home
1) The Return-to-Home feature will NOT work if the GPS signal is insufcient or if GPS is not active.
2) Press the RTH (Return-to-Home)Button or toggle the S2 switch on the remote controller to bring the aircraft
back to the Home Point instead of turning off the remote controller.
3) Tall buildings may adversely affect the Failsafe function. Please adjust the aircraft location, altitude and
speed while returning home to avoid obstacles.
4) Make sure to always y the aircraft within the transmission range of the remote controller.
5) Only use the Failsafe and Return-to-Home functions in case of emergency, as they may be affected by
the weather, the environment, or any nearby magnetic elds.
6) The aircraft cannot avoid obstacles during the Failsafe RTH; therefore it is important to set an appropriate
Failsafe altitude before each ight.
7) When ying indoors, the aircraft cannot perform precision hovering when ying above the surfaces that do
not have a clear pattern. Refer to the “Vision Positioning System” section for complete indoor ying criteria.
Low Battery
1) When the Critical Battery Level Warning activates and the aircraft is descending automatically, you may
push the throttle up to maintain the aircraft's altitude and navigate it to a more appropriate location for
landing.
2) When battery warnings are triggered, promptly bring the aircraft back to the Home Point or land to avoid
losing power during ight and causing damage to the aircraft, property, animals, and people.
Vision Positioning System
1) The Vision Positioning System cannot work properly over surfaces that do NOT have pattern variations.
The effective altitude for the Vision Positioning System to function correctly is less than 2.5 meters above
ground level (AGL).
2) The Vision Positioning System may NOT function properly when the aircraft is ying over water.
3) Keep your pets away from the aircraft when the Vision Positioning System is activated, as the sonar
sensors emit a high frequency sound that is only audible to some pets.
4) Note that the Vision Positioning System may NOT function properly when the aircraft is ying too fast
or too low.
16
©
2017 DJI. All Rights Reserved.
5) Operate the aircraft cautiously when in any of the following situations:
a) Flying over monochrome surfaces (e.g., pure black, pure white, pure red, pure green).
b) Flying over highly reective surfaces;
c) Flying at high speeds (over 8m/s at 2 meters or over 4m/s at 1 meter);
d) Flying over water or transparent surfaces;
e) Flying over moving surfaces or objects;
f ) Flying in an area where the lighting changes frequently or drastically;
g) Flying over extremely dark (< 10 lux) or bright (> 10,000 lux) surfaces;
h) Flying over surfaces that can absorb sound waves (e.g., thick carpet).
i ) Flying over surfaces without clear patterns or texture;
j ) Flying over surfaces with identical repeating patterns or textures (e.g. tiles with same design);
k) Flying over inclined surfaces that will deect sound waves away from the aircraft
6) In the event of loss of the remote controller’s signal, the aircraft will hover for 8 seconds and then auto-land
if it is in “P” mode.
Compliance with Regulations & No Fly Zones
Regulations
To avoid non-compliant behavior, serious injury and property damage, observe the following rules:
1)
DO NOT operate in the vicinity of manned aircraft, regardless of altitude. (Land immediately if
necessary)
2)
DO NOT y the aircraft in densely populated areas, including cities, sporting events, exhibitions,
performances, etc.
3)
DO NOT y the aircraft above the authorized altitude. Remain well clear of and do NOT interfere
with manned aircraft operations. Be aware of and avoid other aircraft and obstacles at all times.
To avoid non-compliant behavior, serious injury and property damage, observe the following rules:
1)
DO NOT y the aircraft near or inside no y zones specied by local laws and regulations. The no y zone
list includes: airports, borders between two sovereign countries or regions, major cities/regions, etc., and
is continuously updated.
2) DO NOT y the aircraft above the authorized altitude
3) ALWAYS keep your aircraft within visual line of sight (VLOS), and use an observer to assist if needed.
4) NEVER use the aircraft to carry illegal or dangerous goods/payloads.
1) Make sure you understand the nature/type of your ight operation (such as for recreation, for public use, or for
commercial use) and have obtained corresponding approval and clearance from the related government
agencies before flight. Consult with your local regulators for comprehensive definitions and specific
requirements. For users operating their aircraft in the United States, please first visit http://www.
knowbeforeyouy.org/ and take action appropriate to your circumstances.
2) Please note that remote controlled aircraft may be banned from conducting commercial activities in
certain countries and regions. Check and follow all local laws and ordinances before ying as those rules
©
2017 DJI. All Rights Reserved.
17
may differ from those stated here.
3) DO NOT y around sensitive infrastructure or property such as power stations, water treatment facilities,
correctional facilities, heavily traveled roadways, government facilities, military zones, etc.
4) Respect the privacy of others when using the camera. DO NOT conduct surveillance operations such
as image capture or video recording on any person, entity, event, performance, exhibition, and property
without authorization or where there is an expectation of privacy, even if the image or video is captured for
personal use.
5) Please be advised that in certain areas, the recording of images and videos from events, performances,
exhibitions, or commercial properties by means of a camera may contravene copyright or other legal
rights, even if the image or video was shot for personal use.
No Fly Zones
DJI always stresses safety during ight, and has therefore developed various aids to help users comply with
local rules and regulations while ying. We strongly recommend that you update the rmware to the latest
version to ensure the following features are fully updated:
No Fly Zones
1) No Fly Zones include but are not limited to major airports around world, borders between two sovereign
countries or regions, major cities/regions, etc.
2) The complete list of No Fly Zones is listed on the ofcial DJI website at http://ysafe.dji.com/no-y and is
subject to periodic updates in line with the latest regulatory requirements without prior notice.
3) Some No Fly Zones are comprised of several zones. Each zone features circles of various sizes. The
aircraft will NOT be able to take off in the inner most zone of the No Fly Zone, and will descend to the
specied altitude when it approaches the edge of the inner most zone. Ground station functionality is
disabled when the aircraft is within a No Fly Zone.
4) Users are NOT able to set up waypoints within No Fly Zones.
Altitude Limit
1) Fly NO higher than 120 meters (400 feet) above ground level and stay away from any surrounding
obstacles.
If you intend to y above the default altitude limit, you are required to accept the prompted disclaimer to
enable the new altitude limit. If a new altitude limit is set, you further understand and agree that data including
but not limited to ight telemetry data and altitude limit changes could be uploaded to and maintained on a
DJI-designated server.
18
©
2017 DJI. All Rights Reserved.
Compliance Information
FCC Compliance Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to
avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall
not be less than 20cm during normal operation.
IC RSS Warning
This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Any Changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
KCC Warning Message
“해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .”
“해당 무선설비는 운용 중 전파혼신 가능성이 있음”
NCC Warning Message
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應改善至無干擾時方
得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及
醫療用電波輻射性電機設備之干擾。
EU Compliance Statement:
SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device is in compliance
with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
©
2017 DJI. All Rights Reserved.
19
A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance
EU contact address: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Declaración de cumplimiento UE:
SZ DJI TECHNOLOGY CO., LTD. por la presente declara que este dispositivo
cumple los requisitos básicos y el resto de provisiones relevantes de la Directiva 2014/53/EU.
Hay disponible online una copia de la Declaración de conformidad UE en www.dji.com/euro-compliance
Dirección de contacto de la UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
EU-verklaring van overeenstemming:
SZ DJI TECHNOLOGY CO., LTD. verklaart hierbij dat dit apparaat voldoet
aan de essentiële vereisten en andere relevante bepalingen van Richtlijn 2014/53/EU.
De EU-verklaring van overeenstemming is online beschikbaar op www.dji.com/euro-compliance
Contactadres EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Declaração de conformidade da UE:
A SZ DJI TECHNOLOGY CO., LTD. declara, através deste documento,
que este dispositivo está em conformidade com os requisitos essenciais e outras disposições relevantes da
Diretiva 2014/53/EU.
Existe uma cópia da Declaração de conformidade da UE disponível online em www.dji.com/euro-compliance
Endereço de contacto na UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Dichiarazione di conformità UE:
SZ DJI TECHNOLOGY CO., LTD. dichiara che il presente dispositivo è
conforme ai requisiti essenziali e alle altre disposizioni rilevanti della direttiva 2014/53/EU.
Una copia della dichiarazione di conformità UE è disponibile online all'indirizzo Web www.dji.com/euro-
compliance
Indirizzo di contatto UE: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
Déclaration de conformité UE :
Par la présente, SZ DJI TECHNOLOGY CO., LTD déclare que cet appareil est
conforme aux principales exigences et autres clauses pertinentes de la directive européenne 2014/53/EU.
Une copie de la déclaration de conformité UE est disponible sur le site www.dji.com/euro-compliance
Adresse de contact pour l'UE : DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
EU-Compliance:
Hiermit erklärt SZ DJI TECHNOLOGY CO., LTD., dass dieses Gerät den wesentlichen
Anforderungen und anderen einschlägigen Bestimmungen der EU-Richtlinie 2014/53/EU entspricht.
Eine Kopie der EU-Konformitätserklärung nden Sie online auf www.dji.com/euro-compliance.
Kontaktadresse innerhalb der EU: DJI GmbH, Industriestrasse. 12, 97618, Niederlauer, Germany
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS
Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be
disposed of separately. The disposal at the communal collecting point via private persons is for free. The
owner of old appliances is responsible to bring the appliances to these collecting points or to similar
collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment
of toxic substances.
Thailand Warning message
เครื่องโทรคมนาคมและอุปกรณ์นี้ มีความสอดคล้องตามข้อกำาหนดของ กทช.
Mexico Warning message
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia,
incluyendo la que pueda causar su operación no deseada.”
Brazil Warning message
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial,
mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário
©
2017 DJI. All Rights Reserved.
This content is subject to change.
Download the latest version from
www.dji.com/support
If you have any questions about this document, please contact DJI by
sending a message to
.
YC.BZ.S00318.02
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
dji Go Guida utente
- Tipo
- Guida utente
- Questo manuale è adatto anche per
in altre lingue
- English: dji Go User guide