Colorado XT
The
Pontoon Boat
OWNER'S MANUAL
CLASSIC ACCESSORIES, LLC
22640 68th AVENUE SOUTH
KENT, WA 98032, USA
©
2016
classicaccessories.com
Colorado XT
Le
Bateau ponton
MANUEL DE L'UTILISATEUR
2
TABLE OF CONTENTS
INTRODUCTION 3
PRODUCT SPECIFICATIONS & CAPACITY 4
SAFETY INFORMATION AND SYMBOLS 5
RESPONSIBILITIES OF THE OPERATOR(S) 6
CERTIFICATE OF ORIGIN AND HIN NUMBERS 7
INFLATION 8
ELECTRIC MOTOR AND BATTERY USE 9
PARTS LIST 10
ASSEMBLY AND USE 11-17
REPAIR AND TROUBLESHOOTING 18-19
CARE AND STORAGE 20
COLORADO XT PONTOON BOAT OWNER’S MANUAL
3
INTRODUCTION
Congratulations on your purchase of a Colorado XT pontoon boat.
This manual has been compiled to help you assemble your boat correctly and
operate it safely. It contains specific details of the boat, including its parts and
equipment, and information on its safe operation, proper care, maintenance and
repair. Please read it carefully, and familiarize yourself with your boat before
using it.
If this is your first pontoon boat, or if you are changing to this type of boat for
the first time, for your own comfort and safety, please ensure that you obtain
handling and operating experience before serious use. Doing so will assure
many years of trouble free use and enjoyment.
PLEASE KEEP THESE INSTRUCTIONS IN A SECURE PLACE, AND TRANSFER THEM
TO THE NEW OWNER IF YOU SELL THE CRAFT.
MODIFICATIONS
Because of possible interference with the factory design and integrity of the
boat, owner modifications to the boat, any of its parts, equipment or systems
are not recommended.
Classic does not recommend that owners modify the boat or any of its parts,
equipment or systems. Such modifications could compromise the design and
integrity of the boat, prevent safe operation, and void warranty coverage.
COLORADO XT PONTOON BOAT OWNER’S MANUAL
Questions, problems, missing parts? Before returning to your retailer, call Classic
Accessories customer service at 1-800-854-2315, 8 a.m. - 4 p.m., PST, Monday-Friday.
Email: customerservice@classicaccessories.com
4
The person/load capacity is partly
dependent on proper seating and load
distribution. Make sure that your load
is distributed evenly and the seating
position is such that, when afloat, the
boat rides level in the water.
WARNING - DO NOT EXCEED THE
MAXIMUM CAPACITY OF THIS BOAT
UNDER ANY CIRCUMSTANCES.
PRODUCT SPECIFICATIONS & CAPACITY
BOAT SPECIFICATIONS
Product Name: COLORADO XT Pontoon Boat
Dimensions: 108 inch L x 56 inch W x 26 inch H
274 cm L x 142 cm W x 66 cm H (top of the seat)
Dry Weight: 77 lbs (35 kg)
Maximum Persons Capacity: 1 person or up to 275 lbs (125 kg)
Maximum Persons & Gear Capacity: 400 lbs (181 kg)
Recommended Inflation Pressure: 2.5 psi (0.17 BAR)
Maximum Motor Thrust: 30 lbs (13.6 kg)
Maximum Motor Shaft Length: 36 inch (91 cm)
BOAT CAPACITY
COLORADO XT PONTOON BOAT OWNER’S MANUAL
August 3, 2016
Classic Accessories, LLC
Maximum Capacity Label - 400 Lbs Max.
Label Size: 5 inch L x 5.7 inch H
Job Number: 16cF55_19397
Black White 20%
black
5 inch
127 mm
5.7
inch
145
mm
0,17 bar (chambres à air principales)
2.5 psi (main chambers)
MANUFACTURER: CLASSIC ACCESSORIES, LLC
KENT, WA 98032, USA • CLASSICACCESSORIES.COM
125 kg
275 lbs
181 kg
400 lbs
13,6 kg
30 lbs
de poussée
thrust
COMPLIANCE NOTICE
MAXIMUM CAPACITIES
AVIS DE CONFORMITÉ
CAPACITÉS MAXIMALES
5
SAFETY INFORMATION AND SYMBOLS
The symbol to the left is the Safety Alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
Indicates a potentially hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in
property damage.
This manual lists certain recommended practices and provides some basic
precautions. However, this list of precautions is not all-inclusive. Users
must follow all applicable laws, rules, and regulations and should exercise
appropriate caution in the safe operation of this pontoon boat.
REMEMBER - always use common sense when using your pontoon boat.
COLORADO XT PONTOON BOAT OWNER’S MANUAL
6
RESPONSIBILITIES OF THE OPERATOR(S)
COLORADO XT PONTOON BOAT OWNER’S MANUAL
IMPORTANT SAFETY AND CARE INFORMATION
SAFETY
• Read this owner’s manual carefully before using
your pontoon boat.
• This product is not to be used by children under
16 years of age or by any child
without adult supervision. This pontoon boat is
not a toy. Check the laws in your state.
• Not for use by children or as pool toy.
• This is not a life saving device.
• You MUST wear an approved personal flotation
device (PFD).
• All safety equipment & PFDs must properly fit the
user, be in good condition and suitable
for your body weight.
• Know and follow all local water safety rules and
boating regulations.
• Do not exceed 400 lbs (181 kg) total cargo weight.
(The weight of you and all of your gear
should not exceed 400 lbs (181 kg).
• Inspect your pontoon boat for wear or damage
before and after each use.
• Class 1 river rating: not for use in rough water,
white water, rapids or open ocean.
• Always use a Coast Guard approved personal
flotation device.
• Never float alone.
• Never use this boat in bad weather.
• Keep sharp objects (knives, fish hooks, etc.) away
from the pontoons.
• Do not use under the influence of drugs or
alcohol.
• Do not tow this pontoon boat.
• Use only in water free from debris and
obstructions.
• Do not use in high wind, rapid currents, open
water or dangerous tides.
• Seek shelter from water if there is threat of
lightning.
• Do not stand on this product while in use.
• Never jump into or dive from this boat.
• Inflate with cold air only.
• Do not over inflate.
• Follow the inflation sequence listed in this
instruction manual.
• Recommended working pressure is 2.5 psi (0.17
bar). DO NOT EXCEED 2.5 PSI.
• Check for leaks before using.
• Remember that air pressure changes with
temperature and elevation so always check
your air pressure before use.
• Partially deflate if leaving boat in direct sunlight
or within a vehicle in sunlight.
• Check all fasteners,screws and wing nuts before
each use.
CARE
• Clean with warm water and a mild detergent.
• To avoid mildew be sure your boat is dry before
storing it.
• Deflate pontoons slightly between uses to extend
the life of your boat.
DO NOT stand on
your boat while
on the water
WARNING
October 07, 2013
Classic Accessories, Inc.
PONTOON TUBE WARNING LABEL - Updated to include the warning ‘Do not tow this pontoon boat’
Label Size: 6.8 inch H x 4.64 inch L
Colors: Black, White and Orange PMS 021C (note: Orange color MUST be Colorfast)
For: all CA and WSL pontoon boats
Job Number: 13cF55_16270
4.64 INCH
6.8 INCH
WARNING
•Notalifesavingdevice
•Notatoy
•Nottobeusedbychildren
underage16
•Donottowthispontoonboat
•Donotoverload
•Alwayswearanapproved
personalotationdevice(life
preserver)
•Checkforleaksbeforeusing
•Useonlyinwaterawayfrom
debrisandobstructions
•Donotoverinate
•Neverdiveintoorfromthisboat
•Neverleaveboatinwaterwhen
notinuse
•Donotuseinhighwind, rapid
currents,openwateror
dangeroustides
•Knowandfollowlocalwater
safetyrulesandboating
regulations
•Followtheinationsequence
listedintheinstructionmanual
•Partiallydeateifleavingin
thesun
•Cecin’estpasunappareilde
sauvetage
•N’estpasjouet
•Nedoitpasêtreutilisépardes
enfantsdemoinsde16ans
•Nepasremorquercebateau
ponton.
•Nepassurcharger
•Veilleràtoujourporterungilet
desauvetageapprouvé
•Vérierqu’iln’yapasdefuites
avanttouteutilisation
•Utiliseruniquementcette
embarcationdansdeseaux
sansdébrisniobstacles
•Veilleràbienconnaîtrel’endroit
denavigation
•Nejamaisplongersurnidepuis
cebateau
•Nepasutiliserlorsdevents
forts,decourantsrapides,en
hautemeroulorsdemarées
dangereuses
•Nejamaislaisserlebateaudans
l’eaulorsqu’iln’estpasutilisé
•Connaîtreetsuivrelesrègles
localesdesécuritéetde
navigation
•Nepastropgoner
•Suivrel’ordredegonageindiqué
danslemanuel
•Dégonerunpeusilaisséau
soleil
AVERTISSEMENT
7
COLORADO XT PONTOON BOAT OWNER’S MANUAL
CERTIFICATE OF ORIGIN
A separate Certificate of Origin form has been included with this pontoon boat. If your state requires
registration of your pontoon boat, you will need to include the HIN number on the form. Check your state's
boating regulations to see if your pontoon boat requires registration.
LOCATING THE HIN (HULL IDENTIFICATION NUMBER)
The HIN Number or "Hull Identification Number" is required for every pontoon boat. Each pontoon boat has
a unique number assigned to it, specific to that pontoon boat only. The assigned number appears on three
locations of the pontoon boat (two locations on the pontoon boat and one location on the frame).
The HIN is located on both pontoon boat skins. they are located to the rear, towards the inside of the boat.
XXQ00001L708
Example of HIN number
CERTIFICATE OF ORIGIN AND HIN NUMBERS
HIN located on the
mounting plate on the
rear platform frame.
Page 53 of 56
11/26/2008
PRODUCT SPECIFICATIONS
Article Code: PB-200
Article Name: FRAME FOR 9-FOOT PONTOON BOAT, WITH WHEEL
HIN DETAILS ON FRAME:
IMPORTANT!! The numbers on the frame pieces and retail package must all match!!
USCG MIC Code
(These letters do not change)
MODEL YEAR (This number changes for
each Model Year. Indicates the year
delivered to Classic.)
Manufacturers Serial Number (reset
counter on January 1st every year)
Month & Year of Certifi cation or
Manufacture *
XXQ00001L708
USCG Mandatory
12 digit HIN
A - January
B - February
C - March
D - April
E - May
F - June
G - July
H - August
I - September
J - October
K - November
L - December
*
HIN font size:
1cm height
Stamp HIN on both motor
mount plates that are
welded to the rear frame.
HIN is located on the
side PVC panel,
towards the inside
of the boat
8
PROPER INFLATION
During final inflation, inflate until most of the wrinkles in the fabric are gone and
it feels firm to the touch, but DO NOT exceed 2.5 psi (0.17 bar) in the main air
chambers.
CAUTION - DO NOT OVER INFLATE YOUR PONTOON BOAT
Water temperature and weather affect the air pressure in the boat. In cold
weather your pontoon boat will lose some pressure because the air will
contract. If this occurs, you may want to add more air.
In hot weather, the air will expand. You must let out some air to prevent the
pontoons from failing from over pressure. Avoid exposing your pontoon boat to
extreme temperatures (hot or cold).
CAUTION
On warm sunny days, keep the pontoon boat either in water or in shade (if kept
inflated on land). This will decrease the risk of overexpansion of the pontoon
chambers posed by rising temperatures, which can result in seam tears,
delamination and pinholes.
Avoid asphalt, sand, pebbles or concrete in direct sunlight as they radiate high
ground heat.
Also understand that changes in altitude will cause the air in the bladders
to expand or contract. If traveling to higher elevation with the pontoon boat
inflated, frequently check the pressure in the pontoons to avoid over pressure.
If traveling to lower elevation you may have to add more air to maintain proper
pressure in the pontoons.
WARNING - ALWAYS CHECK THE AIR PRESSURE IN THE PONTOONS BEFORE
AND DURING EACH USE.
INFLATION
COLORADO XT PONTOON BOAT OWNER’S MANUAL
9
ELECTRIC MOTOR AND BATTERY USE
USING A MOTOR WITH YOUR PONTOON BOAT
Clamp your motor to the motor mount provided on the rear of your boat and
carefully follow the setup and safety instructions provided with your motor.
Using a motor and battery will affect the weight distribution on your boat.
Before using your boat for the first time with a motor check and adjust your seat
position and cargo so your boat rides level in the water.
WARNING - THIS PONTOON BOAT IS NOT RATED FOR USE WITH GASOLINE
OR DIESEL OUTBOARD MOTORS.
WARNING - MAKE SURE TO FOLLOW ALL SAFETY INSTRUCTIONS AND
PROCEDURES THAT CAME WITH YOUR ELECTRIC MOTOR.
IMPORTANT - A MAXIMUM ELECTRIC MOTOR SHAFT LENGTH OF 36 INCH (91 cm)
WITH A MAXIMUM THRUST OF 30 LBS (14 kg) IS RECOMMENDED.
USING A BATTERY WITH YOUR PONTOON BOAT
Be sure to secure your battery to the rear wire platform so that it will not move
or tip during operation. For the best weight distribution we recommend placing
the battery as close to the seat back (center of the boat) as possible.
WARNING - BATTERIES CAN LEAK POISONOUS GASES OR LIQUIDS OR
EXPLODE. USE EXTREME CARE AND FOLLOW ALL SAFETY INSTRUCTIONS AND
PROCEDURES THAT CAME WITH YOUR BATTERY.
WARNING - MAKE SURE THAT YOUR MOTOR AND BATTERY ARE SECURELY
FASTENED TO YOUR PONTOON BOAT BEFORE AND DURING EACH USE.
WARNING - MAKE SURE THAT YOUR PROPELLER IS PLACED AWAY FROM
PONTOONS TO AVOID RUPTURING PONTOON BLADDER.
WARNING - ONLY USE AN APPROVED MARINE BATTERY. USE PROPER
SHIELDING TO PREVENT SHORT CIRCUITS.
COLORADO XT PONTOON BOAT OWNER’S MANUAL
10
Before you begin please unpack the carton and
check that you have all your parts.
IMPORTANT: All small parts are located inside
the center pocket of one of the pontoon storage
bags marked by a tag for easy identification.
Tools Needed: Rubber Mallet
2 Pontoon Frames
(left and right)
1 Seat Frame
1 Clevis Pin
(attached to frame)
1 Seat
(folding with screws
and wingnuts installed)
2 Foot Pegs (left and right)
1 Rear Platform Frame
1 Rear Cargo Platform
1 Rod Holder
with Clevis Pin
2 Bungee Cords with
Plastic Hooks
2 Pontoons
2 Valves (installed)
2 Bladders (installed)
1 Under Seat Apron
1 Stripping Basket
1 Anchor Bag with Cord
2 Detachable
Center Storage Bags
1 Shoulder strap
2 Foam Fly Patches
2 Pontoon Bladder Patches
(Two 60mm self-adhesive patches)
1 Inflation Adapter
1 Inflation Valve
Wrench
1 Retention Cord
1 Allen Wrench Set
(4mm and 6mm ball end)
1 Knob
2 Wire Basket Attachment
Straps
1 Velcro Strap
2 Oar Locks
2 Oar Lock Cotter Pins
8 Frame Clevis Pins
Small Parts (Small parts bag located in pontoon pocket)
Soft Parts
Metal Frame Parts
COLORADO XT PONTOON BOAT PARTS LIST
PTBADAPTOR
PTPATCHKIT
PTBWRENCH
PRT-30-256
PRT-30-073
PRT-30-069
PRT-30-071
PRT-30-074
PRT-30-259
PRT-30-258
PRT-30-076
PRT-30-257
PRT-30-115 / PRT-30-116
PRT-30-023
PRT-30-024
PRT-30-025 / PRT-30-026
PRT-30-027
PRT-30-028
PRT-30-037
PRT-30-167
PRT-30-075
PRT-30-009
PTBVALVE
Sage: PRT-30-032
Pumpkin: PRT-30-035
Sage: PRT-30-033
Pumpkin: PRT-30-036
Sage: PRT-30-030
Pumpkin: PRT-30-031
Sage: PRT-30-033
Pumpkin: PRT-30-036
1 Wheel Fork
1 Wheel
1 Axle, 2 Axle Washers
1 Axle Cotter Pin
Wheel Assembly Parts
Sage: PRT-30-013
Pumpkin: PRT-30-014
2 Oars
(4 pieces or 2 per oar)
PRT-30-068
Oar Parts
11
COLORADO XT PONTOON BOAT OWNER’S MANUAL
ASSEMBLY AND USE
Right hand
pontoon and
frame
Press and
turn on
center
button
Inflation Valve
Inflation
adapter
Insert
into
valve
and
twist to
inflate
It is important to follow these instructions to successfully and safely assemble
your Colorado XT Pontoon Boat.
Please pay particular attention to the bold faced instructions and any
information which has this
symbol next to it.
FRONT
A
B C
D E
1. Confirm that all the parts are present.
(See the parts list on page 10).
2. Identify the right and left pontoons.
You can identify the right and left pontoons by the “R” (right) and “L” (left) labels sewn on the inside
of the rear pocket on top of each.
3. Inflate the air bladders.
The valve is located on the top of the pontoons in front
of the main pocket.
The valve has a center button that opens and closes
the valve by simply pushing down, and turning a
quarter turn. The valve is open when the center button
is down, and closed when it is up. BEFORE INFLATING,
MAKE SURE THE VALVE IS IN THE CLOSED POSITION.
Unscrew the valve cap, make sure the valve is closed
and insert the inflation adapter into the valve and
twist to secure. Inflate using a foot pump or air
compressor with a cone-type nozzle fitting.
Tighten valve using inflation valve wrench, making
sure valve is snug. DO NOT OVERTIGHTEN.
Inflate to approximately 2.5 psi (0.17 BAR).
Inflate until firm but not hard. DO NOT over inflate.
4. Attach the pontoons to the frames.
Each pontoon attaches to a metal pontoon frame with
four webbing attachment straps.
Locate the left and right pontoon frames.
On the front of each pontoon frame (where the front of the
boat will be) there is a “L" (left) or “R” (right) label indicating
left or right.
Place the right pontoon frame on top of the right pontoon
as shown. There is a “L” (left) or “R” (right) label inside the
pocket of each pontoon. The longest straight tube of each
frame should be on the same side of the pontoon as the
pontoon zipper.
Turn
clockwise
to tighten
12
5. Determine the seat placement.
The seat placement determines the center of gravity of the boat. Where you attach the seat to
the frame depends on your size and whether you will be using a motor and battery or carry cargo
on the boat.
Use the following information about seat placement as a guide to
help you setup your boat for optimum balance in the water. After
setup, load your boat with the gear you would use fishing, and try
your boat in shallow water to determine if further seat position
adjustment is necessary for optimum weight distribution.
• If you are up to 5 ft 6 inch (168 cm) in height, place the forward
seat screws (underside of seat) into the front
1/3 of the seat frame bars.
• If you are up to 6 ft (183 cm) in height, place the forward seat
screws (underside of seat) into the middle section of the seat
frame bars.
• If you are over 6 ft (+183 cm) in height, place the forward seat
screws (underside of seat) into the rear 1/3 of the seat frame bars.
• If you use a motor and battery or load the cargo basket with any
heavy items, you will need to adjust the seat forward to offset the load and keep your boat
balanced. The amount you will need to move the seat forward depends on the weight of the
cargo and will necessitate that you try out the new position in shallow water before setting out.
• Try making adjustments for cargo weight by moving seat forward in 1 inch (3 cm) increments.
Seat Frame
1.
2.
3.
4.
5.
COLORADO XT PONTOON BOAT OWNER’S MANUAL
Now attach the two inside and two outside webbing straps
on the pontoon to the pontoon frame. Thread the straps as follows:
1. Through the metal rectangle on the frame…
2. Back to the buckle…
3. Through the buckle threading path…
4. Match the rip-and-grip to each other.
5. Fold the remaining webbing. Back it through the metal rectangle
and trap it between the pontoon and webbing. Repeat for the remaining three straps.
Repeat the procedure with the other pontoon.
6. Attach the seat to the seat frame.
Locate the four 2 inch (5 cm) studs coming out of the bottom
of the seat. Unscrew the wing nuts and remove the washers.
Place the seat with screws facing downwards into the two
bars on the seat frame and position the seat in the place that
is best for your height and weight (see above). Once the seat
placement has been determined, attach the washers and wing
nuts onto the screws and tighten to hold the seat into place.
13
COLORADO XT PONTOON BOAT OWNER’S MANUAL
Note: The anchor bracket can be placed
on EITHER side of the rear platform frame.
Insert the included ball-end wrench into
the bottom of the anchor stud while
holding the nut on top of the stud with
a wrench
to loosen.
1
Attach this
end of anchor
line to the
anchor bag
Note: Seat and p0ntoons
removed for clarity
Front anchor
cord pulley
7. Attach the seat frame to the pontoon frames.
Insert the seat platform tubes onto the pontoon frame posts with the seat
facing the front. The front of the pontoon frames are the ends labeled
“L” (left) and “R” (right). (You may need to LIGHTLY tap the frames with a
rubber mallet to fit).
Align the holes and secure with four clevis pins.
You MUST lock the security retainers on all four clevis pins to insure that
the frame stays together.
Insert clevis pins on the frame side not in between the bladder and
frame to avoid abrasion of the pontoon.
8. Thread the anchor bag cord.
The anchor bag can be attached for
either right or left hand operation. Start
by feeding the cord into the front anchor
cord pulley located on the side of either
pontoon frame. Continue by threading
the cord through the cord guides and
under all frame tubes.
Next, insert the cord through
the rear cord tube guide [1] on the rear
platform frame. Finish by threading the
cord through the pulley mounted on the
rear platform frame and attaching the
cord to the anchor bag.
9. Attach the anchor system.
The anchor system consists of a mesh weight bag and the
length of cord threaded through the frame (step 9).
The bag is filled with rocks or metal weights (not included).
Placing 6 to 8 lbs. (2.7 to 3.6 kg) will keep you anchored in a
light breeze but the weight needed will vary depending on your
weight, your cargo weight, currents and wind.
There are cleats on the inside of each pontoon frame behind
the front anchor cord pulley. Thread the cord around the front
anchor cord pulley and back to the cleat. Thread the cord in
the front and out the back of each cleat. To cleat the cord while
anchoring, simply pull the cord into the jaws of the cleat. Pull up and away from the cleat jaws to release.
If the anchor cord pulleys ever loosen, use the included 4mm allen wrench to tighten.
Front anchor
cord pulley
Anchor cord cleat
10. Attach the rear platform frame.
In order to attach the rear platform frame
you must first partially attach the wire
cargo deck. Start by sliding the bent wire
tabs into the slots welded on to the rear
of each pontoon frame.
Next, push the rear platform frame tubes
into the open tubes on the rear of each
pontoon frame. Make sure to insert the
wire guides on the rear of the wire cargo deck into the corresponding holes on the rear platform frame as you push the
tubes together. Also make sure not to pinch the threaded anchor cord.
Attach the rear corners with two clevis pins. These secure the wire cargo deck and the rear platform frame to the pontoon
frames. Be sure to insert each pin through the cargo deck, the rear platform frame and through the pontoon frames. Lock
both clevis pins.
Motor mount can
be mounted to
either side
14
Thread the tabs
through the loops.
Wrap the strip around
the oarlock upright
COLORADO XT PONTOON BOAT OWNER’S MANUAL
A B
12. Insert the foot pegs.
Insert the foot pegs into the pontoon frame as shown. Starting
with a position in the middle of the adjustment range, align
the holes and secure with two clevis pins. Sitting in the seat
comfortably with your feet on the foot pegs, your legs should
be bent slightly at the knee. Adjust foot pegs again if needed
and secure with the two clevis pins.
11. Insert the oar locks.
Insert an oar lock into the top of both oar lock brackets on the pontoon frames. There
are three oar lock positions; we suggest starting with the forward most position. If
you have the seat set back you may prefer the middle or back position. Secure each
oar lock with an oar lock clevis pin.
13. Attach the under seat apron.
The under seat apron has a rip-and-grip tab
opening on one side. This allows for installation.
Install with this tab facing up and to the rear of
the boat.
Start by opening the tab and slipping the apron
under the seat and around the seat mounting
bolts. Reattach the tab once it's in position.
Next, attach the sides of the apron to the sides
of each pontoon, matching up the corresponding
rip-and-grip sections.
Attach rip-and-grip tab
to close the opening
Attach rip-and-grip
edges to the sides
of the pontoons
Seat shown lifted off
seat frame for clarity
14. Mount the stripping basket.
The stripping basket is a sturdy and efficient way of
containing your fishing line while fly casting. Mount it to
the top of either pontoon float, or across your lap.
OPTION A: To attach, orient the basket so the long side
of the basket with the three loops sewn into its bottom
faces outboard, or away from the seat. Next, find the
three rip-and-grip tabs sewn to the outboard side of the
pontoon. Thread these through the corresponding loops
on the bottom of the basket.
Finish by attaching the rip-and-grip strap on the
outboard top edge of the basket to an upright of the
oarlock bracket. See drawing A a right.
OPTION B: Place your stripping basket across your lap
by using the 2 bungee hooks to the sides of the basket
and attaching to the pontoon frame. See drawing B at
right.
15
15. Attach the center storage bags.
To mount the bags to the pontoon float first find the three
sets of plastic loops sewn into each long side of the bag
bottom. These mate up with rip-and-grip straps along the
tops of both pontoons.
Orient the storage bag on either pontoon so that the flap
of the top bag pocket, when open, folds away from the
operator. Match up rip-and-grip tape on the bottom of the
bag to the rip-and-grip strips on the top of the pontoon
float and press together. Then thread the rip-and-grip
straps through the hoops on the bottom of the bag to fully
secure.
You can use both the bags on the boat at the same time
or only use one when using the stripping basket mounted
to the top of the pontoon. You can secure the other half
of the bag in the wire cargo deck, using the wire basket
attachment straps.
To use the bag as a shoulder tote, match up the sections
of rip-and-grip tape sewn on the back of each bag. Next,
find the rip-and-grip straps on the end of one bag and
thread through the corresponding loops on the end of the
other bag. Repeat with the other end. Finish by attaching
the shoulder strap to both ends of the completed bag.
Note: Boat
shown without
frame for clarity
Match up rip-
and-grip strips
to attach
Bottom of
the bag shown
Loop the rip-and-grip straps
through hoops to make the two
storage bags into a shoulder tote
Close up view - loop the
rip-and-grip straps through
hoops to attach to pontoon
COLORADO XT PONTOON BOAT OWNER’S MANUAL
16. Set up the oars and oar stops.
First, assemble the two piece oars. Align the holes so that
the button pops through the oar handle.
To set an oar in an oar lock, drop the blade of the oar into the
oar lock. Slide the oar until the oar stop rests against the oar
lock. The oar stops are adjustable if desired.
*Helpful Hint : Oars do not need to be taken apart in order to place in the oar locks.
oar stop
17. Attach the rod holder.
The rod holder may be placed in three different positions on
either the left or right pontoon frame. You can hold your rod to
the back (1), out to the side (2) or to the front (3). The rod holder
attaches with the clevis frame pins as in step 8.
To use the rod holder first unwrap the rip-and-grip strap on the
end. Put your rod in the holder butt end first then turn it to drop
the reel handle into the cutout on the side of the rod holder.
Keeping one hand on your rod use your other hand to wrap the
strap around the front of the reel to secure your rod in place in
the holder.
You can purchase extra rod holders directly from
Classic Accessories customer service.
Hoops along both sides
Loop straps through hoops
To make the shoulder tote
ATTENTION
To Prevent Failure: Check and retighten all screws on both oarlocks before each
use with a Phillips screwdriver.
retighten all screws (2)
oar
oar lock
16
COLORADO XT PONTOON BOAT OWNER’S MANUAL
Bottom view
of boat
Off center line
receiver tube
(UP position)
Center line
receiver tube
(DOWN position)
Screw knob
19. Attach the wheel.
Turn your pontoon boat on its side. You will notice under the
seat that there are two square receiver tubes. The one that
is mounted on center line is used when the wheel is in the
DOWN position, when moving your pontoon boat. The other
is angled off center line, and is used when the wheel is in the
UP position, for storing your boat and during fishing.
To secure the wheel in the DOWN position, slide the square
wheel support tube with the wheel facing down into the
center line mounted square receiver tube. Line up the holes
in both the support tube and the receiver tube and insert the
clevis pin attached to the seat frame. Insert and tighten the
screw knob to keep the frame snug.
To secure the wheel in the UP position, rotate the wheel
assembly 90 degrees so the wheel axle is facing the wire
cargo deck, slide the wheel support tube into the
off center line mounted square receiver tube. Line up the
holes in both tubes and insert the clevis pin.
Wheel shown in
the UP position
18. Assemble the wheel and frame.
Slide the wheel between the forks of the wheel frame. Slide one
washer on the axle, insert the axle through both the forks and the
wheel hub. Slip the other washer over the end of the axle and secure
with the cotter pin.
It may be necessary to apply side force to the forks in order to secure
the cotter pin into the hole in the axle.
Applying a small amount of waterproof grease to the axle regularly will
keep it rolling smoothly.
17
20. Moving your pontoon boat.
To move your boat using the wheel, you must first have the wheel
installed in the down position.
To move your boat, grasp the ends of the front of each pontoon and
pull up to raise the front of the boat off the ground. You may also use
the foot pegs as handles.
Make sure not to overload your boat with cargo when moving as it
could damage the wheel and frame.
21. Attach the retention cord.
Locate the retention cord. This keeps your boat from floating away
when you stand in shallow water to fish.
To attach, simply clip the carabiners at each end of the cord to the D-rings at the front of each pontoon float.
22. The bladder repair kit.
Included with your boat are self-adhesive tube patches to repair any tears or holes in the pontoon bladders.
We recommend storing these in one of the pockets to keep them available for repairs.
23. Do the final fitting and adjustments.
Sit in the boat on dry land and adjust the foot pegs, seat position and oar lock placement to your leg length
and preference.
Float your pontoon boat in shallow water. Push off, get seated comfortably, place your feet on the foot pegs and check to
see if you are level in the water. (This is easier with a another person on shore).
WARNING - The goal is to find your balance point. When you are floating in the boat it should be level in the water.
WARNING - Using a motor and battery or placing heavy cargo in the wire cargo deck may necessitate moving the
seat forward.
WARNING - If you need to adjust the seat or foot pegs bring the boat back to shore and make the
needed adjustments.
WARNING - DO NOT STAND UP IN YOUR BOAT WHILE ON THE WATER.
YOU COULD LOSE YOUR BALANCE AND FALL OVERBOARD.
WARNING - THIS BOAT IS NOT RECOMMENDED FOR USE IN SALTWATER.
Practice going forward and backward a bit to get comfortable. Then catch some fish and enjoy your boat!
COLORADO XT PONTOON BOAT OWNER’S MANUAL
18
COLORADO XT PONTOON BOAT OWNER’S MANUAL
REPAIR & TROUBLESHOOTING
1. Start by giving the pontoon skins a visual inspection.
Is the pontoon skin ripped or torn? Are there any major scuff marks?
If so, it might be an indication of a bladder tear or leak.
2. Check if you can hear air escaping the bladder in any suspected areas. You can apply
soapy water to any suspected areas as well. A leak will produce bubbles. If you find a
hole, fix it using the methods listed on the following page.
If you don't find a leak using these methods, check the inflation valves:
3. Give them a visual inspection, making sure the valve is closing properly and the valve
cap closes securely.
4. Check if you can hear air escaping. You may also use soapy water around the valve. If you find that a valve is leaking
air around its edge, the valve may be loose.
If your boat appears to be losing air, it might not be because of a leak. Changes in air temperature,
elevation and use on cold water (which can cool the air inside the pontoon bladders) can all have an
effect on the air inside the bladders. If none of these factors have changed, you may need to look for
a leak. Follow the steps listed below.
Checking For A Leaking Valve
The inflation valve consists of a two-part assembly. There
is the inflation valve itself
and the inflation valve cage.
The inflation valve cage
protects the inflation valve
from damage and is bonded
into the pontoon bladder.
To tighten a loose valve,
inflate pontoon until firm,
insert the Inflation Valve
Wrench into the valve and
twist clockwise. Be careful
not to overtighten valve.
If the valve is difficult to turn, remove the valve completely
and add a small amount of silicon grease to the valve
O-ring and reassemble.
If the valve is not leaking around its edge, you may have
a defective
valve.
Please visit
contact
Classic
Accessories
customer
service to
order a new
valve.
If you must
remove the
pontoon bladder from the pontoon skin to make a repair,
you must completely unscrew the inflation valve from the
inflation valve cage. When installing bladder, make sure
to align the valves in the bladder with the valve openings
in the skin. Since the pontoon skin is captive in between
the inflation valve cage and the inflation valve, care must
be taken not to tear, rip or stress either the bladder or the
skin by over-tightening the valve.
Inflation Valve Cage
(bonded to pontoon bladder)
Inflation Valve
Valve O-ring
Check valve edge
for leaks
Turn counter-clockwise to loosen
Turn
clockwise
to tighten
Inflation
Valve
Wrench
Inflation
Valve Wrench
19
COLORADO XT PONTOON BOAT OWNER’S MANUAL
Repairing Tears and Holes in Pontoon Bladders
If your pontoon bladder becomes torn or punctured, use the enclosed patches to fix
it. It may be necessary to take the pontoon bladder out of the pontoon skin. Look in
the Troubleshooting section on the previous page
for this procedure. To fix a hole or tear, follow the
steps listed below.
1. For best results, it is important to apply patch
to a clean, dry surface and that the surface
temperature is 50° F (10° C) or warmer.
2. Use an alcohol prep pad to clean the surface to
be repaired. If you do not have an alcohol prep
pad, use a 50/50 mixture of isopropyl alcohol
and water. After cleaning, allow the surface to
dry completely.
3. Cut a patch to the correct size with scissors.
Allow for the patch size to extend 1 inch (2.5 cm) beyond all edges of the tear. Cut
the patch with rounded corners. This will make it difficult for the corners to peel up
after it is attached.
4. Peel back 1/8 inch - 1/4 inch (0.3 cm - 0.6 cm) of paper backing and position and
anchor the exposed patch edge, allowing the patch to extend 1 inch (2.5cm) beyond
all edges of the tear.
5. Slowly peel the paper backing while carefully applying the patch over the tear. Take
care to avoid air bubbles.
6. Rub the patch firmly for proper adhesion and allow to cure for 4 hours before use.
Extend patch
one inch (2.5 cm)
beyond tear
REPAIR & TROUBLESHOOTING
20
CARE & STORAGE
COLORADO XT PONTOON BOAT OWNER’S MANUAL
TRANSPORTING YOUR PONTOON BOAT
The pontoon boat can be transported partially or fully assembled or inflated. Due to
size constraints, many customers will keep their frame fully intact and simply inflate
and attach their pontoons once they reach their destination. Various methods such as
a pickup truck bed, trailer, or roof rack can be used to transport your boat. If you are
carrying a partially or fully assembled and or inflated boat, please consult with your
vehicle, trailer, or roof rack manufacturer.
CARE FOR YOUR BOAT
The pontoon boat can be cleaned with soap and water then rinsed.
Use a soft rag for hard to clean areas.
SEASONAL STORAGE OF YOUR BOAT
Remove pontoons from the frame, empty pockets of any sharp objects that may
puncture the skin. Deflate completely and fold for storage. Store pontoons away from
sharp objects, heat or abrasive wear. Dismantle frame and boat parts and store in box.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Classic Accessories 69770 Istruzioni per l'uso
- Tipo
- Istruzioni per l'uso
- Questo manuale è adatto anche per
in altre lingue
Documenti correlati
Altri documenti
-
Sevylor SV270S-HF Manuale del proprietario
-
Regal 29 OBX Manuale del proprietario
-
Bayliner 1999 5788 Pilothouse Manuale del proprietario
-
-
-
Boston Whaler 250 Outrage Manuale del proprietario
-
-
-
Edgewater Networks 318CC Owner Assistance Manual
-
Sea Ray 2004 290 BOW RIDER Supplement Manuale del proprietario