NEC MultiSync® LCD1560NX (Black) Manuale utente

MultiSync LCD1560NX

User’s Manual

UÏivatelská pﬁíruãka

Bedienerhandbuch

δηγίες ρήσης

Manual del usuario

Manuel Utilisateur

Manuale utente

Gebruikershandleiding

Podr´cznik u˝ytkownika

Руководство пользователя

Kullan∂c∂ Klavuzu

00Cover_all.p65 18/11/02, 11:35 am1

For the Customer to use in U.S.A. or Canada

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 950.

Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 950.

FCC Information

1. Use the attached specified cables with the MultiSync LCD1560NX colour monitor so as not to interfere with radio and

television reception.

(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,

and meet the following condition.

Power supply cord Non shield type, 3-conductor

Length 2.0 m

Plug shape

U.S.A

(2) Shielded video signal cable. Use of other cables and adapters may cause interference with radio and television

reception.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional

suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:

“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government

Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

00Cover_all.p65 18/11/02, 11:35 am2

Congratulations! You have just purchased a

TCO’99 approved and labeled product! Your choice

has provided you with a product developed for

professional use. Your purchase has also

contributed to reducing the burden on the

environment and also to the further development of

environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an

established method for encouraging the adaptation of goods and

services to the environment. The main problem, as far as

computers and other electronics equipment are concerned, is that

environmentally harmful substances are used both in the products

and during the manufacturing. Since it has not been possible for

the majority of electronics equipment to be recycled in a

satisfactory way, most of these potentially damaging substances

sooner or later enter Nature.

There are also other characteristics of a computer, such as energy

consumption levels, that are important from the viewpoints of both

the work (Internal) and natural (external) environments. Since all

methods of conventional electricity generation have a negative

effect on the environment (acidic and climate-influencing

emissions, radioactive waste, etc.), it is vital to conserve energy.

Electronics equipment in offices consume an enormous amount of

energy since they are often left running continuously.

What does labelling involve?

This product meets the requirements for the TCO’99 scheme

which provides for international and environmental labelling of

personal computers. The labelling scheme was developed as a

joint effort by the TCO (The Swedish Confederation of Professional

Employees), Svenska Naturskyddsforeningen (The Swedish

Society for Nature Conservation) and Statens Energimyndighet

(The Swedish National Energy Administration).

The requirements cover a wide range of issues: environment,

ergonomics, usability, emission of electrical and magnetic fields,

energy consumption and electrical and fire safety.

The environmental demands concern restrictions on the presence

and use of heavy metals, brominated and chlorinated flame

retardants, CFCs (freons) and chlorinated solvents, among other

things. The product must be prepared for recycling and the

manufacturer is obliged to have an environmental plan which must

be adhered to in each country where the company implements its

operational policy. The energy requirements include a demand that

the computer and/or display, after a certain period of inactivity,

shall reduce its power consumption to a lower level in one or more

stages. The length of time to reactivate the computer shall be

reasonable for the user.

Labelled products must meet strict environmental demands, for

example, in respect of the reduction of electric and magnetic fields,

physical and visual ergonomics and good usability.

Environmental Requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables,

wires, casings and housings. In turn, they delay the spread of fire.

Up to thirty percent of the plastic in a computer casing can consist

of flame retardant substances. Most flame retardants contain

bromine or chloride and these are related to another group of

environmental toxins, PCBs, which are suspected to give rise to

severe health effects, including reproductive damage in fisheating

birds and mammals, due to the bioaccumulative* processes. Flame

retardants have been found in human blood and researchers fear

that disturbances in foetus development may occur.

TCO’99 demand requires that plastic components weighing more

than 25 grams must not contain flame retardants with organically

bound chlorine and bromine. Flame retardants are allowed in the

printed circuit boards since no substitutes are available.

Lead**

Lead can be found in picture tubes, display screens, solders and

capacitors. Lead damages the nervous system and in higher

doses, causes lead poisoning.

TCO’99 requirement permits the inclusion of lead since no

replacement has yet been developed.

Cadmium**

Cadmium is present in rechargeable batteries and in the

colourgenerating layers of certain computer displays. Cadmium

damages the nervous system and is toxic in high doses.

TCO’99 requirement states that batteries, the colourgenerating

layers of display screens and the electrical or electronics

components must not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and switches,

Mercury damages the nervous system and is toxic in high

doses.

TCO’99 requirement states that batteries may not contain any

Mercury. It also demands that no mercury is present in any of

the electrical or electronics components associated with the

display unit.

CFCs (freons)

CFCs (freons) are sometimes used for washing printed circuit

boards. CFCs break down ozone and thereby damage the ozone

layer in the stratosphere, causing increased reception on Earth

of ultraviolet light with consequent increased risks of skin cancer

(malignant melanoma).

The relevant TCO’99 requirement; Neither CFCs nor HCFCs

may be used during the manufacturing and assembly of the

product or its packaging.

*Bio-accumulative is defined as substances which accumulate

within living organisms.

**Lead, Cadmium and Mercury are heavy metals which are

Bio-accumulative.

To obtain complete information on the environmental criteria

document, order from:

TCO Development Unit

SE-114 94 Stockholm

SWEDEN

FAX Number: +46 8 782 92 07

E-mail (Internet): [email protected]

You may also obtain current information on TCO’99 approved

and labelled products by visiting their website at:

http://www.tcodevelopment.com

TCO’99

00Cover_all.p65 18/11/02, 11:35 am3

Index

Warning, Caution ............................... English-1

Declaration......................................... English-1

Contents............................................. English-2

Quick Start ......................................... English-2

Controls.............................................. English-7

Recommended use............................ English-9

Varování, Upozornûní........................... âesky-1

Prohlá‰ení ............................................ âesky-1

Obsah .................................................. âesky-2

Rychl˘ start ........................................... âesky-2

Ovládací prvky ..................................... âesky-7

Provozní pokyny ................................... âesky-9

Warnung, Vorsicht .............................Deutsch-1

Erklärung...........................................Deutsch-1

Inhalt .................................................Deutsch-2

Kurzanleitung ....................................Deutsch-2

Bedienelemente ................................Deutsch-7

Einsatzempfehlungen........................Deutsch-9

ΠΡΕΙ∆ΠΙΗΣΗ, ΠΡΣΗ ..... Ελληνικά-1

∆ήλωση ......................................... Ελληνικά-1

Περιεµενα ................................. Ελληνικά-2

Γρήγρη Εκκίνηση ....................... Ελληνικά-2

Πλήκτρα Ελέγυ ........................ Ελληνικά-7

Πρτεινµενη ρήση .................. Ελληνικά-9

Advertencia, Peligro .......................... Español-1

Declaración .......................................Español-1

Contenido..........................................Español-2

Inicio rápido....................................... Español-2

Controles........................................... Español-7

Uso recomendado............................. Español-9

Avertissement, Attention .................. Français-1

Déclaration....................................... Français-1

Sommaire......................................... Français-2

Mise en marche rapide .................... Français-2

Commandes..................................... Français-7

Conseils d’utilisation ........................ Français-9

Avviso, Attenzione.............................. Italiano-1

Dichiarazione ..................................... Italiano-1

Contenuto .......................................... Italiano-2

Guida rapida ...................................... Italiano-2

Controlli.............................................. Italiano-7

Uso consigliato................................... Italiano-9

Waarschuwing, Let op!................ Nederlands-1

Kennisgeving............................... Nederlands-1

Inhoud ......................................... Nederlands-2

Snel aan de slag ..........................Nederlands-2

Besturingselementen .................. Nederlands-7

Aanbevolen gebruik .................... Nederlands-9

Uwagi dotyczàce zasilania monitora .... Polski-1

Ostrze˝enie, Uwaga ............................. Polski-2

Deklaracja ............................................ Polski-2

ZawartoÊç opakowania ........................ Polski-3

Pod∏àczenie monitora .......................... Polski-3

Przyciski ............................................... Polski-8

Zalecenia eksploatacyjne................... Polski-11

Предупреждение, Внимание ......... Русский-1

Заявление ....................................... Русский-1

Содержимое ................................... Русский-2

Краткое руководство по

началу работы ................................ Русский-2

Органы управления........................ Русский-7

Рекомендации по эксплуатации.... Русский-9

D∂kkat, Uyari ....................................... Türkçe-1

Bildirim ................................................ Türkçe-1

∑çindekiler ............................................ Türkçe-2

H∂zl∂ Baµlama ...................................... Türkçe-2

Kontroller ............................................. Türkçe-7

Tavsiye Edilen Kullan∂m ...................... Türkçe-9

00Cover_all.p65 18/11/02, 11:35 am4

English

âesky

Deutsch

Ελληνικά

Español

Français

Italiano

Nederlands

Polski

Русский

Türkçe

01b_XChapterOpener 18/11/02, 11:35 am1

01b_XChapterOpener 18/11/02, 11:35 am2

English

English-1

Declaration

Declaration of the Manufacturer

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS

THE PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

RISK OF ELECTRIC SHOCK • DO NOT OPEN

As an ENERGY STAR

®

Partner, NEC-Mitsubishi Electronics Display of America, Inc. has determined that this product meets the

ENERGY STAR guidelines for energy efficiency. ENERGY STA R is a U.S. registered mark.

IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A and XGA are registered trademarks of International Business Machines

Corporation.

Apple and Macintosh are registered trademarks of Apple Computer Inc.

Microsoft and Windows are registered trademarks of the Microsoft Corporation.

NEC is a registered trademark of NEC Corporation.

ErgoDesign is a registered trademark of NEC-Mitsubuishi Electric Visual Systems Corporation in Austria, Benelux, Denmark,

France, Germany, Italy, Norway, Spain, Sweden, U.K.

NaViSet is a trademark of NEC-Mitsubishi Eletronics Display Europe GmbH in the countries of the EU and Switzerland.

All other trademarks or registered trademarks are property of their respective owners.

We hereby certify that the colour monitor

MultiSync LCD1560NX (NL2501) is in

compliance with

Council Directive 73/23/EEC:

– EN 60950

Council Directive 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

and marked with

NEC-Mitsubishi Electric Visual

Systems, Corp.

MS Shibaura Bldg., 13-23,

Shibaura 4-chome,

Minato-Ku, Tokyo 108-0023, Japan

Caution:

When operating the MultiSync LCD1560NX with a 220-240V AC power source in Europe, use the power cord provided with

the monitor.

In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment.

If a power cord is not supplied with this equipment please contact your supplier.

When operating the MultiSync LCD1560NX with a 220-240V AC power source in Australia, use the power cord provided with

the monitor. If a power cord is not supplied with this equipment please contact your supplier.

For all other cases, use a power cord that matches the AC voltage of the power outlet and has been approved by and

complies with the safety standard of your particular country.

01_English 18/11/02, 11:35 am1

English-2

Quick Start

To attach the MultiSync LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display

card in your system (Figure A.1). Tighten all screws.

For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your

system (Figure A.2). Tighten all screws.

For the MAC: Connect the MultiSync Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal

cable to the MultiSync Macintosh cable adapter (Figure B.1). Tighten all screws.

NOTE: Some Macintosh systems do not require a Macintosh cable adapter.

3. Remove cable cover. Connect the 15-pin mini D-SUB of the video signal cable and DVI signal cable (not included) to the

appropriate connector on the back of the monitor (Figure C.1).

4. Connect one end of the power cord to the monitor and the other end to the power outlet.

Collect cables and keep them at backside of the stand (Figure C.2). And cover the cables by the optional Cable

management Cover (Figure C.3).

Please check Tilt, Rise and Lower monitor screen when you manage cables.

NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.

5. The Vacation Switch on the right side of the monitor must be turned on (Figure D.1). Turn on the monitor with the Power

Button and the computer.

NOTE: The Vacation Switch is a true on/off switch. If this switch is on the OFF position, the monitor cannot be turned on

using the front button. DO NOT switch on/off repeatedly.

6. Analog input only: No-touch auto adjust automatically adjusts the monitor to optimal settings upon initial setup for most

timings. For further adjustments, use the following OSM controls:

• Auto Adjust Contrast

• Auto Adjust

Refer to the Controls section of this User’s Manual for a full description of these OSM controls.

NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.

Contents

Your new NEC MultiSync LCD monitor box* should contain the following:

• MultiSync LCD1560NX monitor with tilt base

• Power Cord

•Video Signal Cable

• User’s Manual

• CD ROM (includes complete User’s Manual in PDF format).

To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.

*

Remember to save your original box and packing material to transport or ship the monitor.

User’s Manual CD ROMVideo Signal CablePower Cord

01_English 18/11/02, 11:35 am2

English

English-3

Figure C.1

Input2 (DVI)

Input1 (D-Sub)

Input2 (DVI)

Input1 (D-Sub)

Cable cover

Figure A.1 Figure B.1

Macintosh

Cable Adapter

(not included)

Figure A.2

Figure C.2

Figure C.3

01_English 18/11/02, 11:35 am3

English-4

Raise and Lower Monitor Screen

The monitor may be raised or lowered.

To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1).

Tilt

Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1).

Remove Monitor Stand for Mounting

To prepare the monitor for alternate mounting purposes:

1. Disconnect all cables.

2. Place hands on each side of the monitor and lift up to the highest position.

3. Place monitor face down on a non-abrasive surface (Figure S.1).

Vacation Switch

Power Button

Figure D.1

Figure TS.1

Figure RL.1

Figure S.1

01_English 18/11/02, 11:35 am4

English

English-5

4. Remove the hinge cover (Figure R.1 and Figure R.2).

5. Remove the 4 screws connecting the monitor to the stand and lift off the stand assembly (Figure R.3) the monitor is now

ready for mounting in an alternate manner.

6. Connect the AC cord, signal cable and audio cable to the back of the monitor (Figure R.4).

7. Reverse this process to reattach stand.

NOTE: Use only VESA-compatible alternative mounting method.

Handle with care when removing stand.

Figure R.3

Figure R.1

Figure R.2

01_English 18/11/02, 11:35 am5

English-6

NOTE: This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) when mounting.

To meet the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability

under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g.

GS mark).

4 SCREWS

(MAX depth: 8.5 mm)

If use other screw,

check depth of hole.

Weight of LCD assembly: 2.8kg (MAX)

Replace screws

Tighten all screws

Thickness of bracket (arm)

2.0 ~ 3.2 mm

75 mm

Figure R.4

01_English 18/11/02, 11:35 am6

English

English-7

Controls

OSM (On-Screen-Manager) Controls

The OSM controls on the front of the monitor function as follows:

To access OSM press any of the control buttons (<, >, -, +, EXIT).

To change signal input, press the SELECT button.

NOTE: OSM must be closed in order to change signal input.

NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the

RESET function by pressing the EXIT button.

Brightness/Contrast Controls

BRIGHTNESS

Adjusts the overall image and background screen brightness.

CONTRAST

Adjusts the image brightness in relation to the background.

AUTO ADJUST (Analog input only)

Adjusts the image displayed for non-standard video inputs.

Auto Adjust (Analog input only)

Automatically adjusts the Image Position, the H. Size and Fine setting.

Position Controls (Analog input only)

LEFT/RIGHT

Controls Horizontal Image Position within the display area of the LCD.

DOWN/UP

Controls Vertical Image Position within the display area of the LCD.

H. SIZE

Adjusts the horizontal size by increasing or decreasing this setting.

Should the “AUTO Adjust function” do not give you a satisfactory picture setting, a further tuning can be

performed using the “H.Size” function (dot clock). For this a Moiré test pattern could be used. This function

may alter the width of the picture. Use Left/Right Menu to center the image on the screen. If the H.Size is

wrongly calibrated, the result would look like on the left drawing. The image should be homogeneous.

Menu

Exits the OSM controls.

Exits to the OSM main menu.

Moves the highlighted area left/right to select control menus.

Moves the highlighted area up/down to select one of the controls.

Moves the bar left/right to increase or decrease the adjustment.

Active Auto Adjust function. Enter the OSM controls. Enter the OSM sub menu.

Resets the highlighted control menu to the factory setting.

Control

EXIT

< / >

- / +

SELECT

RESET

When H.SIZE value is

wrong.

When H.SIZE value is

improved.

When H.SIZE value is

correct.

01_English 18/11/02, 11:36 am7

English-8

FINE

Improves focus, clarity and image stability by increasing or decreasing this setting.

Should the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, a

fine tuning can be performed using the “Fine” function. It improves focus, clearity and image stability by

increasing or decreasing this setting.

For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like

on the left drawing. The image should be homogeneous.

Colour Control Systems

Six colour presets select the desired colour setting (NATIVE colour presets are standard and cannot be

changed).

R, G, B

Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour

will appear on screen and the direction (increase or decrease) will be shown by the bars.

NATIVE

Original colour presented by the LCD panel that is unadjustable.

Tools

LANGUAGE

OSM control menus are available in seven languages.

OSM POSITION

You can choose where you would like the OSM control image to appear on your screen. Selecting OSM

Location allows you to manually adjust the position of the OSM control menu left, right, down or up.

OSM TURN OFF

The OSM control menu will stay on as long as it is use. In the OSM Turn Off submenu, you can select how

long the monitor waits after the last touch of a button to shut off the OSM control menu. The preset choices

are 10, 20, 30, 45, 60 and 120 seconds.

OSM LOCK OUT

This control completely locks out access to all OSM control functions without Brightness and Contrast.

When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the

OSM controls are locked out. To activate the OSM Lock Out function, press SELECT, then “+” key and hold

down simultaneously. To de-activate the OSM Lock Out, press SELECT, then “+” key and hold down

simultaneously.

RESOLUTION NOTIFIER

This optimal resolution is 1024 x 768. If ON is selected, a message will appear on the screen after

30 seconds, notifying you that the resolution is not at 1024 x 768.

HOT KEY

You can adjust the brightness and contrast directly. When this function is set to ON, you can adjust the

brightness with < or >, contrast with + or - key, while the OSM menu is off. The standard OSM menu can

be accessed with the EXIT button.

OFF TIMER

Monitor will automatically power-down when the end user has selected a pre-determined amount of time.

FACTORY PRESET

Selecting Factory Preset allows you to reset all OSM control settings back to the factory settings. The

RESET button will need to be held down for several seconds to take effect. Individual settings can be reset

by highlighting the control to be reset and pressing the RESET button.

When FINE value is

wrong.

When FINE value is

correct.

01_English 18/11/02, 11:36 am8

English

English-9

Recommended use

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE

THE FOLLOWING WHEN SETTING UP AND

USING THE MULTISYNC LCD COLOUR MONITOR:

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose

you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful

or fatal or may cause electric shock, fire or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to

the monitor.

• Do not place any objects onto the monitor and do not use the monitor outdoors.

• The inside of the fluorescent tube located within the LCD monitor contains mercury. Please follow the bylaws or rules of

your municipality to dispose of the tube properly.

Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following

conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

• Do not bend power cord.

• Do not use monitor in high temperatured, humid, dusty, or oily areas.

• Do not cover vent on monitor.

• If monitor is broken, do not come in contact with the liquid crystal.

• If glass is broken. Handle with care.

• Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated

openings or place the monitor near a radiator or other heat sources. Do not put anything on top of

monitor.

• The power cable connector is the primary means of detaching the system from the power supply. The

monitor should be installed close to a power outlet which is easily accessible.

• Handle with care when transporting. Save packaging for transporting.

CAUTION

Information

DISPLAY MODE

Indicates the current display resolution and frequency setting of the monitor.

MONITOR INFO.

Indicates the model and serial numbers of your monitor.

OSM Warning

OSM Warning menus disappear with Exit button.

NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or

when there is a change of input signal or video is inactive, the No Signal window will appear.

RESOLUTION NOTIFIER: This function gives a warning of use with optimized resolution. After power is

turned on or when there is a change of input signal or the video signal doesn’t have proper resolution, the

Resolution Notifier window will open. This function can be disabled in the TOOL menu.

OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After

the power is turned on or there is a change of input signal or the video signal doesn’t have proper timing,

the Out Of Range menu will appear.

01_English 18/11/02, 11:36 am9

English-10

• Image Persistence: Image persistence is when a residual or “ghost” image of a previous image remains visible on the

screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for

a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an

image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to

erase the image.

NOTE: As with all personal display devices, NEC-Mitsubishi Electronics Display-Europe recommends using a moving

screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN

REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

• For optimum performance, allow 20 minutes for warm-up.

• Adjust the monitor height so that the top of the screen is at or slightly below eye level.

Your eyes should look slightly downward when viewing the middle of the screen.

• Position your monitor no closer than 40 cm and no further away than 70 cm from your

eyes. The optimal distance is 50 cm.

• Rest your eyes periodically by focusing on an object at least 6 m away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to minimize glare

and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.

• If reflected light makes it hard for you to see your screen, use an antiglare filter.

• Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any

cleaning solution or glass cleaner!

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize

turning your head while you are typing.

•Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image effects).

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Use the preset Size and Position controls with standard signals.

• Use the preset Colour Setting.

• Use non-interlaced signals with a vertical refresh rate between 60-75 Hz.

• Do not use primary colour blue on a dark background, as it is difficult to see and may produce eye fatigue to insufficient

contrast.

01_English 18/11/02, 11:36 am10

âesky

âesky-1

Prohlá‰ení

Prohlá‰ení v˘robce

CHRA≈TE ZA¤ÍZENÍ P¤ED DE·TùM A VLHKEM. ZABRÁNÍTE TAK NEBEZPEâÍ POÎÁRU NEBO ÚRAZU

ELEKTRICK¯M PROUDEM. POLARIZOVANOU ZÁSTRâKU JEDNOTKY NEPOUÎÍVEJTE VE SPOJENÍ SE ZÁSUVKOU

PRODLUÎOVACÍ ·≈ÒRY NEBO JIN¯MI ZÁSUVKAMI, POKUD KOLÍKY NELZE ZCELA ZASUNOUT.

UVNIT¤ ZA¤ÍZENÍ SE NACHÁZÍ VYSOKONAPùËOVÉ KOMPONENTY, PROTO SK¤Í≈ NEOTEVÍREJTE. SERVIS

SVù¤TE KVALIFIKOVANÉ OSOBù.

VAROVÁNÍ

UPOZORNùNÍ

UPOZORNùNÍ: Z DÒVODU SNÍÎENÍ RIZIK ÚRAZU ELEKTRICK¯M PROUDEM NEODNÍMEJTE KRYT (NEBO ZADNÍ

âÁST). UVNIT¤ SE NENACHÁZEJÍ DÍLY, DO KTER¯CH UÎIVATEL MÒÎE ZASAHOVAT. SERVIS SVù¤TE

KVALIFIKOVANÉ OSOBù.

Tento symbol upozorÀuje uÏivatele na neizolované napûtí v rámci jednotky, jehoÏ intenzita mÛÏe b˘t

dostateãnû vysoká, aby zpÛsobila úraz elektrick˘m proudem. Jak˘koli kontakt s libovoln˘m dílem uvnitﬁ

jednotky je proto nebezpeãn˘.

Tento symbol upozorÀuje uÏivatele na dÛleÏitou literaturu t˘kající provozu aúdrÏby jednotky dodanou

spoleãnû s tímto zaﬁízením. Chcete-li pﬁedejít problémÛm, doporuãujeme peãlivé proãtení pﬁíslu‰n˘ch

materiálÛ.

RIZIKO ÚRAZU ELEKTRICK¯M PROUDEM • NEOTVÍRAT

Spoleãnost NEC-Mitsubishi Electronics Display of America Inc. jako partner ENERGYSTAR

®

urãila, Ïe tento produkt splÀuje

poÏadavky smûrnic ENERGYSTAR pro efektivní vyuÏití energie. ENERGYSTA R je v USA registrovaná známka.

IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A a XGA jsou registrované obchodní znaãky spoleãnosti International Business

Machines Corporation.

Apple a Macintosh jsou registrované ochranné známky spoleãnosti Apple Computer Inc.

Microsoft a Windows jsou registrované ochranné známky spoleãnosti Microsoft Corporation.

NEC je registrovaná ochranná známka spoleãnosti NEC Corporation.

ErgoDesign je registrovaná ochranná známka spoleãnosti NEC Mitsubishi Electric Visual Systems Corporation v Rakousku,

Beneluxu, Dánsku, Francii, Nûmecku, Itálii, Norsku, ·panûlsku, ·védsku a Spojeném království.

NaViSet je ochranná a známka spoleãnosti NEC-Mitsubishi Electronics Display Europe GmbH v zemích Evropské Unie a ve

·v˘carsku.

V‰echny ostatní ochranné známky nebo registrované ochranné známky jsou majetkem pﬁíslu‰n˘ch vlastníkÛ.

Tímto potvrzujeme, Ïe barevn˘ monitor

MultiSync LCD1560NX (NL2501) splÀuje

smûrnice 73/23/EEC:

– EN 60950

smûrnice 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

a je opatﬁen oznaãením

NEC-Mitsubishi Electric Visual

Systems, Corp.

MS Shibaura Bldg., 13-23,

Shibaura 4-chome,

Minato-Ku, Tokyo 108-0023, Japan

Upozornûní:

Pﬁi provozu monitoru MultiSync LCD1560NX v síti s napûtím 220-240V v Evropû pouÏívejte síÈovou ‰ÀÛru dodávanou s

monitorem.

Ve Spojeném království se smí pouÏívat k tomuto monitoru jen schválená ‰ÀÛra BS se zalitou zástrãkou a s ãernou pojistkou

(5A). Není-li napájecí ‰ÀÛra souãástí zaﬁízení, spojte se s dodavatelem.

Pﬁi provozu monitoru MultiSync LCD1560NX v síti s napûtím 220-240V v Austrálii pouÏívejte síÈovou ‰ÀÛru dodávanou s

monitorem. Není-li napájecí ‰ÀÛra souãástí zaﬁízení, spojte se s dodavatelem.

Ve v‰ech ostatních pﬁípadech pouÏívejte napájecí ‰ÀÛru, která se shoduje se stﬁídav˘m napûtím zásuvky a která vyhovuje

bezpeãnostním pﬁedpisÛm dané zemû.

02_Czech 18/11/02, 11:36 am1

âesky-2

Obsah

Dodávka nového monitoru LCD NEC MultiSync* by mûla obsahovat následující poloÏky:

• monitor MultiSync LCD1560NX s otoãnou základnou,

• napájecí ‰ÀÛra,

• kabel pro video signál,

• uÏivatelská pﬁíruãka,

• CD-ROM (zahrnuje kompletní uÏivatelskou pﬁíruãku ve formátu PDF). Pro zobrazení

uÏivatelské pﬁíruãky musíte mít na poãítaãi nainstalovanou aplikaci Acrobat Reader 4.0.

* PÛvodní krabici a balicí materiál uschovejte pro pﬁípadnou pﬁepravu nebo odeslání monitoru.

Rychl˘ start

Monitor MultiSync LCD pﬁipojíte k poãítaãi následujícím zpÛsobem:

1. Vypnûte poãítaã.

2. Pro poãítaã PC nebo Macintosh s digitálním v˘stupem DVI: Pﬁipojte jeden konec signálního kabelu DVI (není souãástí

dodávky) ke konektoru grafické karty poãítaãe (Obr. A.1). Dotáhnûte v‰echny ‰rouby.

Poãítaã PC s analogov˘m v˘stupem: V poãítaãi pﬁipojte 15kolíkovou minizástrãku D-SUB signálního kabelu ke konektoru

grafické karty (Obr. A.2). Dotáhnûte v‰echny ‰rouby.

Poãítaãe Macintosh: Pﬁipojte k poãítaãi adaptér Multisync Macintosh a k adaptéru pﬁipojte 15kolíkov˘ konektor signálního

kabelu D-SUB (Obr. B.1). Dotáhnûte v‰echny ‰rouby.

POZNÁMKA: U nûkter˘ch poãítaãÛ Macintosh není nutné pouÏívat tento kabelov˘ adaptér.

3. Sundejte kryt kabelu. V poãítaãi pﬁipojte 15kolíkovou mini-zástrãku D-SUB kabelu pro video signál a kabelu DVI (není

souãástí dodávky) k odpovídajícímu konektoru na zadní stranû monitorur (Obr. C.1).

4. Pﬁipojte napájecí ‰ÀÛru k monitoru a druh˘ konec zapojte do elektrické zásuvky.

Pﬁipojte kabely a veìte po boãní stranû podstavc (Obr. C.2). Zakryjte kabely doplÀkov˘m krytem kabelÛ (Obr. C.3).

Pﬁi manipulaci s kabely zkontrolujte náklon monitoru v boãním a pﬁedozadním smûru.

POZNÁMKA: V ãásti Upozornûní této pﬁíruãky najdete pokyny k v˘bûru správné napájecí ‰ÀÛry.

5. Hlavní vypínaã na pravé stranû monitoru musí b˘t zapnut˘ (Obr. D.1). Zapnûte pomocí hlavního vypínaãe monitor a poãítaã.

POZNÁMKA: Hlavní vypínaã pﬁedstavuje skuteãn˘ vypínaã. Pokud je tento vypínaã v poloze vypnuto, monitor nelze zapnout

pﬁedním tlaãítkem. NEP¤EPÍNEJTE vypínaã opakovanû.

6. Pouze analogov˘ vstup: Funkce bezdotykového automatického seﬁízení automaticky nastaví monitor pﬁi poãáteãní instalaci

pro vût‰inu ãasování. K dal‰ímu seﬁízení pouÏijte následující ovladaãe OSM:

• automatické upravení kontrastu,

• automatické seﬁízení.

Úpln˘ popis tûchto ovladaãÛ OSM je uveden v kapitole Ovládací prvky v této uÏivatelské pﬁíruãce.

POZNÁMKA: Vyskytnou-li se potíÏe, proãtûte si kapitolu OdstraÀování problémÛ dále v této pﬁíruãce.

UÏivatelská pﬁíruãka CD-ROMKabel pro video signálNapájecí ‰ÀÛra

02_Czech 18/11/02, 11:36 am2

âesky

âesky-3

Obrázek C.1

Vstup2 (DVI)

Vstup1 (D-Sub)

Vstup2 (DVI)

Vstup1 (D-Sub)

Kryt kabelu

Obrázek A.1 Obrázek B.1

Adaptér kabelu

Macintosh (není

souãástí v˘bavy)

Obrázek A.2

Obrázek C.2

Obrázek C.3

02_Czech 18/11/02, 11:36 am3

âesky-4

Hlavní vypínaã

Tlaãítko napájení

Nastavení v˘‰ky monitoru

Monitor lze zvednout nebo sníÏit.

Chcete-li obrazovku posunout nahoru nebo dolÛ, uchopte monitor na obou stranách a zvednûte jej nebo spusÈte do poÏadované

v˘‰ky (Obr. RL.1).

Sklon monitoru

Uchopte obû strany obrazovky monitoru a upravte sklon podle poÏadavkÛ (Obr. TS.1).

Odebrání podstavce pﬁi pﬁemístûní monitoru

Pﬁíprava monitoru na pﬁemístûní:

1. Odpojte v‰echny kabely.

2. Uchopte monitor za obû strany a zvednûte jej do nejvy‰‰í polohy.

3. PoloÏte monitor obrazovkou dolÛ na hladk˘ povrch (Obr. S.1).

Obrázek D.1

Obrázek TS.1

Obrázek RL.1

Obrázek S.1

02_Czech 18/11/02, 11:36 am4

La pagina sta caricando ...

NEC MultiSync® LCD1560NX (Black) Manuale utente

Questo manuale è adatto anche per

NEC MultiSync® LCD1560NX (Black) Manuale utente

in altre lingue

Documenti correlati