Sharp LL-T17A3 Manuale del proprietario

Marca: Sharp

Modello: LL-T17A3

Categoria: TV

Tipo: Manuale del proprietario

LCD Monitor

LCD Farbmonitor

Moniteur LCD

Monitor LCD

 !"=== = !

LL-T17A3

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EPLOI

MANUALE D’USO

MANUAL DE FUNCIONAMIENTO

 !"

Table of Contents / Inhaltsverzeichnis / Table des matières / Indice / Índice / 

Notice for Users in Europe ....................................................................................................................... 3

Notice for users in the UK ......................................................................................................................... 4

Notice for Users in the Australia ............................................................................................................... 4

Notice for Users in the USA ...................................................................................................................... 5

TCO 95 / 99 .......................................................................................................................................... 6

English .................................................................................................................................. 7

Deutsch ................................................................................................................................. 27

Français ................................................................................................................................. 47

Italiano ................................................................................................................................... 67

Español ................................................................................................................................. 87

 ........................................................................................................................................ 107

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended

by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit

Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées

par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata

dalla direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ

73/23/ΕΟΚ, óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por

medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras

av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/

68/EEC.

CAUTION :

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION :

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT :

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN

ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L’APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING :

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION :

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

PRECAUCION :

A FIN DE EVITAR DESCARGAS ELÉCTRICAS, DESCONECTE EL ENCHUFE DE LA RED ANTES DE

REALIZAR CUALQUIER OPERACIÓN DE SERVICIO.

ATTENZIONE:

PER EVITARE FOLGORAZIONI, SCOLLEGATE IL CAVO DI COLLEGAMENTO ALLA RETE IN

ALTERNATA PRIMA DI EFFETTUARE UN INTERVENTO DI SERVIZIO TECNICO.

ATTENZIONE:

PER UNO SCOLLEGAMENTO ELETTRICO COMPLETO, TIRATE FUORI LA SPINA PRINCIPALE.

01_LL-T17A3_notice.p65 9/12/2002, 6:01 PM3

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code :

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows. The wire which is coloured

GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E

or by the safety earth or coloured green or green-and-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N

or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter

L or coloured red.

Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified electri-

cian.

"WARNING :THIS APPARATUS MUST BE EARTHED"

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

01_LL-T17A3_notice.p65 9/12/2002, 6:01 PM4

EnglishDeutschFrançaisItalianoEspañolEnglish

Notice for Users in the USA

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B

computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T17A3

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undersized operation.

Responsible Party : SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL :1-800-BE-SHARP

* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.

Disposal of these materials may be regulated due to environmental considerations. For disposal or

recycling information, please contact your local authorities or the Electronics Industries

Alliance:www.eiae.org

01_LL-T17A3_notice.p65 9/12/2002, 6:01 PM5

LL-T17A3-B LL-T17A3-H

Congratulations!

You have just purchased a TCO’95 or TCO’99 approved and

labelled product! Your choice has provided you with a

product developed for professional use. Your purchase has

also contributed to reducing the burden on the environment

and also to the further development of environmentally

adapted electronics products.

This product meets the requirements for the TCO’95 or

TCO’99 scheme which provides for an international

environmental and quality labelling of personal computers.

The labelling scheme was developed as a joint effort by the

TCO (The Swedish Confederation of Professional Employ-

ees), Svenska Naturskyddsforeningen (The Swedish Society

for Nature Conservation), Statens Energimyndighet (The

Swedish National Energy Administration) and SEMKO AB.

The requirements cover a wide range of issues: environ-

ment, ergonomics, usability, reduction of electric and

magnetic fields, energy consumption and electrical safety.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an

established method for encouraging the adaptation of goods

and services to the environment. The main problem, as far

as computers and other electronics equipment are con-

cerned, is that environmentally harmful substances are

used both in the products and during their manufacture.

Since it is not so far possible to satisfactorily recycle the

majority of electronics equipment, most of these potentially

damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as

energy consumption levels, that are important from the

viewpoints of both the work (internal) and natural (external)

environments. Since all methods of electricity generation

have a negative effect on the environment (e.g. acidic and

climate-influencing emissions, radioactive waste), it is vital

to save energy. Electronics equipment in offices is often left

running continuously and thereby consumes a lot of energy.

What does the environmenal labelling involve?

The environmental demands has been developed by

Svenska Naturskyddsforeningen (The Swedish Society for

Nature Conservation). These demands impose restrictions

on the presence and use of heavy metals, brominated and

chlorinated flame retardants, CFCs (freons) and chlorinated

solvents, among other things. The product must be

prepared for recycling and the manufacturer is obliged to

have an environmental policy which must be adhered to in

each country where the company implements its opera-

tional policy.

The energy requirements include a demand that the

computer and/or display, after a certain period of inactivity,

shall reduce its power consumption to a lower level in one

or more stages. The length of time to reactivate the

computer shall be reasonable for the user.

Below you will find a brief summary of the environmental

requirements met by this product. The complete environ-

mental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): development@tco.se

Current information regarding TCO’99 approved and

labelled products may also be obtained via the Internet,

using the address: http://www.tco-info.com/

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards,

cables, wires, casings and housings. Their purpose is to

prevent, or at least to delay the spread of fire. Up to 30% of

the plastic in a computer casing can consist of flame

retardant substances. Most flame retardants contain

bromine or chloride, and those flame retardants are

chemically related to another group of environmental toxins,

PCBs. Both the flame retardants containing bromine or

chloride and the PCBs are suspected of giving rise to

severe health effects, including reproductive damage in fish-

eating birds and mammals, due to the bio-accumulative *

processes. Flame retardants have been found in human

blood and researchers fear that disturbances in foetus

development may occur. The relevant TCO´95 and TCO’99

demand require that plastic components weighing more

than 25 grams must not contain flame retardants with

organically bound bromine or chlorine. Flame retardants are

allowed in the printed circuit boards since no substitutes are

available.

Cadmium **

Cadmium is present in rechargeable batteries and in the

colour-generating layers of certain computer displays.

Cadmium damages the nervous system and is toxic in high

doses.

TCO’95 requirement states that batteries may not contain

more than 25 ppm (parts per million) of cadmium. The

colour-generating layers of display screens must not contain

any cadmium.

The relevant TCO’99 requirement states that batteries, the

colour-generating layers of display screens

and the electrical or electronics components must not

contain any cadmium.

Mercury **

Mercury is sometimes found in batteries, relays and

switches. It damages the nervous system and is

toxic in high doses.

TCO’95 requirement states that batteries may not contain

more than 25 ppm (parts per million) of mercury. The

relevant TCO’99 requirement states that batteries may not

contain any mercury.

Both TCO´95 and TCO´99 also demand that mercury is not

present in any of the electrical or electronics components

associated with the labelled unit. There is however one

exception. Mercury is, for the time being, permitted in the

back light system of flat panel monitors as there today is no

commercially available alternative. TCO aims on removing

this exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO’95 and TCO’99 requirement state that

neither CFCs nor HCFCs may be used during the manufac-

ture and assembly of the product. CFCs (freons) are

sometimes used for washing printed circuit boards. CFCs

break down ozone and thereby damage the ozone layer in

the stratosphere, causing increased reception on earth of

ultraviolet light with e.g. increased risks of skin cancer

(malignant melanoma) as a consequence.

Lead **

Lead can be found in picture tubes, display screens, solders

and capacitors. Lead damages the nervous system and in

higher doses, causes lead poisoning. The relevant TCO’95

and TCO´99 requirement permit the inclusion of lead since

no replacement has yet been developed.

* Bio-accumulative is defined as substances which

accumulate within living organisms

** Lead, Cadmium and Mercury are heavy metals which are

Bio-accumulative.

01_LL-T17A3_notice.p65 9/12/2002, 6:01 PM6

EnglishDeutschFrançaisItalianoEspañolEnglish

Tips and safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting the monitor and turning the monitor on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting the monitor to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting the monitor to a power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Turning the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Turning the power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing set-up information and the ICC profile (for Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Information about the ColorSync profile (for MacOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the screen display and speaker volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting the speaker volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Setting color mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Automatic screen adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Manual screen adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Monitor care and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Instructions for attaching a VESA compliant arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table of Contents

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM7

Tips and safety precautions

- The TFT color LCD panel used in this monitor is

made with the application of high precision

technology. However, there may be minute points

on the screen where pixels never light or are

permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or

brightness. Please note that these are not

malfunctions but common phenomena of LCDs

and will not affect the performance of the

monitor.

- Do not leave the screen displaying idly for long

periods of time, as this could cause afterimage to

remain.

- If the brightness is adjusted to the minimum

setting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using a

computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by

the customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be

upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is

high, or where the monitor may come into

contact with oil or steam, as this could lead to

fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric

shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the

monitor to come into contact with strong shocks

or vibrations. Causing the monitor to fall or topple

over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating equipment

or anywhere else where there is likelihood of

high temperature, as this may lead to generation

of excessive heat and outbreak of fire.

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or overly bend it. Also, do

not add extension cords. Damage to the cord

may result in fire or electric shock.

- Use only the AC adapter supplied with the

monitor. Using an AC adapter other than that

supplied may lead to fire.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating.

Monitor and accessory checklist

- Please check that the following items are

included in the package.

- LCD monitor (1)

- AC adapter (1)

(model name: NL-A64J)

- Analog signal cable (1)

(model name: 0NIT15V1-0056(LL-T17A3-H) /

0NIT17A3-0115(LL-T17A3-B) )

- Audio cable (1)

(model name: 0NIT17A3-0010(LL-T17A3-H) /

0NIT17A3-0116(LL-T17A3-B) )

- Utility Disk (For Windows/Macintosh) (1)

- Operation manual (1)

- Use only the cables supplied with the monitor.

Notes:

- You are advised to retain the carton in case the

monitor needs to be transported.

- Sharp Corporation holds authorship rights to the

Utility Disk program. Do not reproduce it without

permission.

- The shape of the supplied accessaries may not

be exactly same as shown in this booklet.

Use of AC adapter

- Do not use the AC adapter for other than the

specified equipment.

- Unplug the AC adapter if it is not used for long

time.

- Do not place any objects on the AC adapter.

- Do not use the AC adapter outdoors.

- Do not attempt to repair the AC adapter if it is

broken or malfunctioning. Refer the servicing to

the service representative.

- Do not try to open the AC adapter.

- Do not use water or wet cloth for cleaning the AC

adapter.

Manual Scope

- In this booklet, Microsoft Windows XP will be

referred to as [WindowsXP], Microsoft Windows

Millenium as [WindowsMe], Microsoft Windows

2000 as [Windows2000], Microsoft Windows 98

as [Windows98], Microsoft Windows 95 as

[Windows95], and Microsoft Windows Version 3.1

as [Windows3.1]. When there is no need to

distinguish between programs, the term

[Windows] will be used.

- Microsoft and Windows are registered

trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

02_LL-T17A3_gb.p65 10/3/2002, 12:01 PM8

EnglishDeutschFrançaisItalianoEspañolEnglish

Product description

8 9

1. MENU button ............................ This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

2. / MODE button ..................... When the OSD Menu is displayed:

This button is used to select menu options.

When the OSD Menu is not displayed:

This button is used to set COLOR MODE.

buttons ............................. When the OSD Menu is displayed:

These buttons are used to increase or decrease the value of a

selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness and speaker

volume.

4. Power button ............................ Pressing this button turns the power on. (After turning the power on, it

may take a little time before the screen displays.)

Press the button again to turn the power off.

5. Power LED ............................... This LED is lit green when in use and orange when in power-saving

mode.

6. Speakers .................................. Audio entering via the monitor and the external device connected to

the monitor can be heard.

7. Audio input terminal ................. A computer’s audio output terminal can be connected here. The audio

cable included should be used.

8. Power terminal ......................... The AC adapter is connected here.

9. Analog RGB input terminal ...... The analog signal cable is connected here.The analog signal cable

included should be used.

10. Security lock anchor ................ By connecting a security lock (commercially available) to the security

lock anchor, the monitor is fixed so that it cannot be transported.

The security slot works in conjunction with Kensington Micro Saver

Security Systems.

11. Ventilation openings ................ Note: Never block the ventilation openings as this may lead to

overheating inside the monitor and result in malfunction.

12. Lock disable button .................. This button is used when folding back the display section.

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM9

Product description

Standing up and adjusting the monitor

CAUTION!

- Pressure from hands on the LCD panel could

cause damage.

- Be careful not to allow your fingers to be

pinched.

- Be careful not to place any objects on the cables.

Doing so may result in disconnection or other

problems.

Standing up the monitor

Press down on the stand and lift up the top section

of the monitor.

Folding up the monitor

1.Remove the AC adapter and the cable.

2. If carrying out adjustments to the monitor, place

it upright.

3. While pressing the rear lock disable button (1),

gently fold back the monitor (2).

(1)

(2)

Angle adjustment

Adjust to an easy to view angle.

- Do not use the monitor when tilted back beyond

approximately 20º.The monitor may fall over

leading to injury or malfunction.

Prohibited range

approx.20°

approx.5°

approx.20°

approx.5°

approx.45°

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM10

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

CAUTION!

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to overly bend the cable or add

extension cords as this could lead to a

malfunction.

Connecting the monitor to a computer

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

If connecting to a D-sub 15 pin 2 row Apple Power

Macintosh, attach a Macintosh conversion adapter

(commercially available) to the analog signal cable.

Note:

- When connecting to a notebook, if the notebook

computer's screen is set so that it is displaying at

the same time, the MS-DOS screen may not be

able to display properly. In this case, change the

settings so that only the monitor is displaying.

Analog RGB terminal

(Mini D-Sub 15 pin, 3 row)

Analog signal cable

Macintosh conversion adapter

Connect the accessory audio cable

Connecting the monitor to a power source

1.Connect the AC adapter to the monitor's power

terminal.

2.Attach the power cord to the AC adapter and

place the power plug into the AC outlet.

AC adapter

Power terminal

Power cord

AC outlet

Audio input terminal

Audio cable

Audio output terminal

02_LL-T17A3_gb.p65 10/3/2002, 12:01 PM11

Turning the power on

1.Press the monitor's POWER button.

2.Turn on the computer.

The power LED will be lit green, and the screen

will display an image.

Notes:

- If using the monitor for the first time or after

having changed the system settings during use,

perform an automatic screen adjustment.

- Depending on the computer or OS, it may be

necessary to use the computer to install monitor

set-up information. If so, follow the steps below to

install the monitor set-up information.

Turning the power off

1. Turn the computer off.

2. Press the monitor's POWER button.

The Power LED will disappear.

OFF

If the monitor is not going to be used for a long

period of time, be sure to unplug it from the AC

outlet.

Connecting the monitor and turning the monitor on and off

Turn on the

computer

Press power button

Turn the

computer off

Installing set-up information and the

ICC profile (for Windows)

Depending on the computer or OS, it may be

necessary to use the computer to operate the

installation of monitor set-up information etc. If so,

follow the steps below to install the monitor set-up

information. (Depending on the type of computer or

OS, command names and methods may differ.

Please follow the computer’s own operation

manual while reading this.)

About the ICC profile

An ICC (International Color Consortium) profile

is a file that describes the color characteristics

of the LCD monitor. By using an application that

works together with an ICC profile, a high color

resolution can be realized.

- Windows98/2000/Me/XP all use the ICC profile.

- When installing Windows98/2000/Me/XP set-

up information (described below), the ICC

profile is also installed. If you would like to

install the ICC program only, please refer to

Installing the ICC profile on page 14.

- When using an ICC profile, set [COLOR

MODE] and [WHITE BALANCE] to [STD] .

Installing set-up information

For Windows95

Installing monitor set-up information into Win-

dows95.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy

manufacturer's files from:] is [A:] then click

[OK].

6. Confirm that the monitor details are selected,

and click [OK].

7. Check that the monitor details are displayed,

then click [Apply].

8. Click [OK], and close the window.

9. Remove the Utility Disk from the A drive.

02_LL-T17A3_gb.p65 9/13/2002, 2:37 PM12

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

For Windows98

Installing monitor set-up information into Win-

dows98, and setting the monitor's ICC profile as a

predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

If the "Add new Hardware Wizard" has appeared:

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Click [Next].

3. Check [Display a list of all the drivers in a

specific location, so you can select the driver

you want.], then click [Next].

4. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files

from:] is [A:], and click [OK].

5. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish]. If the "Add

New Hardware Wizard" appears, repeat the

installation commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not ap-

peared:

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Click [Next].

7. Click on [Display a list of all the drivers in a

specific location, so you can select the driver

you want.], then click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files

from:] is [A:], and click [OK].

9. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.

12. Remove the Utility Disk from the A drive.

For Windows2000

Installing monitor set-up information into Win-

dows2000, and setting the monitor's ICC profile as

a predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. Click on [Properties], [Driver] and [Update

Driver].

6. When [Upgrade Device Driver Wizard] appears,

click [Next].

7. Check [Display a list of the known drivers for

this device so that I can choose a specific

driver] and click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files

from:] is [A:], and click [OK].

9. Select the monitor from the list displayed and

click [Next].

10. Click [Next], confirm that the monitor's name

appears on the screen, and click [Finish]. If

[The Digital Signature Not Found] appears, click

[Yes].

11. Click on [Close].

12. Click [OK], and close the window.

13. Remove the Utility Disk from the A drive.

For WindowsMe

Installing monitor set-up information into

WindowsMe, and setting the monitor's ICC profile

as a predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

If the "Add new Hardware Wizard" has appeared:

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Check [Specify the location of the driver

[Advanced]] and click [Next].

3. Check [Display a list of all the drivers in a

specific location, so you can select the driver

you want.], then click [Next].

4. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files

from:] is [A:], and click [OK].

5. Select the monitor details from the list, then

click [Next], [Next], and [Finish]. If the "Add new

Hardware Wizard" appears, repeat the

installation commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM13

Connecting the monitor and turning the monitor on and off

If the "Add New Hardware Wizard" has not ap-

peared:

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Check [Specify the location of the driver

[Advanced]] and click [Next].

7. Check [Display a list of all the drivers in a

specific location, so you can select the driver

you want.] and click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files

from:] is [A:], and click [OK].

9. Select the monitor details, then click [Next],

[Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.

12. Remove the Utility Disk from the A drive.

For WindowsXP

Installing monitor set-up information into

WindowsXP, and setting the monitor's ICC profile

as a predetermined value.

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk in the computer's A drive.

2. Click on the [Start] button. Choose [Control

Panel].

3. Switch to "Classic View".

4. Double click on [Display].

5. Click on [Settings], [Advanced] and [Monitor].

6. Click on [Properties], [Driver] and [Update

Driver].

7. When [Hardware Update Wizard] appears,

check [Install from a list or specific location

[Advanced]] and click [Next].

8. Check [Don't search. I will choose the driver to

install.] and click [Next].

9. Click on [Have Disk], confirm that [Copy

manufacturer's files from:] is [A:], and click

[OK].

10. Select the monitor from the list displayed and

click [Next].

If [has not passed Windows Logo testing...]

appears, click [Continue Anyway].

11. Confirm that the monitor's name appears on the

screen.

12. Click on [Finish].

13. Click on [Close].

14. Click [OK], and close the window.

15. Remove the Utility Disk from the A drive.

Installing the ICC profile

Installing the monitor’s ICC profile. (If the set-up

information has already been installed, so too has

the profile, and there is no need to install it.)

This explanation assumes that the floppy disk drive

is "A drive".

1. Place the Utility Disk in the computer’s A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings] and [Advanced].

5. Click on [General] and from [Compatibility]

select [Apply the new display setting without

restarting], then click on [Color Management].

6. Click [Add], and select [3 ½ Floppy [A:]] as the

file location.

7. Choose the color profile that you would like to

install, and click on [Add].

8. Choose the profile and click on [Set As Default].

9. Click [OK], and close the window.

10. Remove the Utility Disk from the A drive.

- When using an ICC profile, set [COLOR MODE]

and [WHITE BALANCE] to [STD] .

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM14

EnglishDeutschFrançaisItalianoEspañolEnglish

Connecting the monitor and turning the monitor on and off

Information about the ColorSync

profile (for MacOS)

About the ColorSync profile

ColorSync is the Apple Corporation's color

management system and is a function that

enables color resolution to be realized when

used with a compatible application. A ColorSync

profile describes the color characteristics of the

LCD monitor.

Notes:

- This monitor's ColorSync profile works with

MacOS8.5 or above.

- When using the ColorSync profile, set

[COLOR MODE] and [WHITE BALANCE] to

[STD].

Setting up the ColorSync profile

Notes:

- A floppy disk drive is necessary. In addition, it is

necessary to have PC Exchange or File

Exchange installed in your system.

- Depending on the type of computer or OS,

command names and methods may differ. Please

follow the computer’s own operation manual

while reading this.

1.Place the Utility Disk (provided) into the

computer’s floppy disk drive.

2.Copy the profile to be used from the Mac folder

on the Utility Disk to the ColorSync profile folder

located within the system folder.

3.Using the ColorSync on the control panel,

choose the profile to be used.

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM15

Adjusting the screen display and speaker volume

Adjustment the backlight (right column)

Brightness of backlight can be adjusted.

Speaker volume adjustment (p. 17)

Speaker volume can be adjusted.

COLOR MODE setting (p. 17)

Color tone can be set.

Automatic screen adjustment (p.17)

The CLOCK, PHASE, H-POS (horizontal position-

ing) and V-POS (vertical positioning) functions can

be adjusted automatically.

Manual screen adjustment (p. 18)

Fine adjustments can be made using the On

Screen Display (OSD) Menu.

Note:

- All adjustments will be saved even after turning

the power off.

Resetting all adjustment values

All adjustment values can be returned to their

original ex-factory values in one command.

1. Turn off the monitor power.

2. Press the MENU button and the / MODE

button simultaneously, and while doing this press

the power button (i.e. turn the power on).

Continue to press the button until [ALL RESET]

appears on the screen. Reset is complete when

the displayed message disappears.

Notes:

- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

ADJUSTMENT menu reset

Settings of items in the ADJUSTMENT Menu

(CLOCK, PHASE, H-POS, V-POS) can be returned

to their original ex-factory values.

1. Turn on the monitor power.

2. Press the MENU button and the

button

simultaneously. When [RESET] appears on the

screen, the reset is complete.

Adjustment lock function

By disabling the control buttons (i.e. setting the

lock) any attempted changes to adjusted values will

be voided.

1. Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

[ADJUSTMENT LOCKED] will appear on

the screen, and the lock will be set.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Adjustment lock release

1. Turn off the monitor power.

2.While pressing the MENU button, press the

power button (i.e. turn the power on).

[ADJUSTMENT UNLOCKED] will appear

on the screen, and the lock will be

removed.

Adjusting the backlight

1. Without the OSD Menu being displayed, push the

or the button.

VOLUME 80

BRIGHT 31

SELECT

...

[ / MODE]

2.Check that "BRIGHT" is selected.

If it is not selected, press the / MODE button

and select "BRIGHT".

3. Adjust by pressing the

button (darker) or

button (lighter).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

02_LL-T17A3_gb.p65 9/13/2002, 2:37 PM16

EnglishDeutschFrançaisItalianoEspañolEnglish

Adjusting the speaker volume

1. Without the OSD Menu being displayed, push the

or the button.

VOLUME 80

BRIGHT 31

SELECT

...

[ / MODE]

2.Check that "VOLUME" is selected.

If it is not selected, press the / MODE button

and select "VOLUME".

3. Adjust by pressing the

button (decrease) or

button (increase).

Note:

- On Screen display for adjustment disappears

several seconds after the last operation.

Setting color mode

Color tone can be set as below.

STD

Displays image with the color tone results from

original scheme of liquid crystal panel.

sRGB

sRGB is international standard of color represen-

tation specified by IEC (International

Electrotechnical Commission).

Color conversion is made in taking account of

liquid crystal’s characteristics and represents

color tone close to it original image.

VIVID

Displays an image with dynamic and VIVID

primary colors.

- If COLOR MODE is set to [sRGB] or [VIVID],

[WHITE BALANCE] in the ADJUSTMENT Menu

is set to [STD].

How to set

Press the / MODE button when the ADJUST-

MENT Menu is not displayed.

Each time the button is pressed the next menu item

appears. (STD → sRGB → VIVID → STD)

On Screen display for adjustment disappears

several seconds after the last operation.

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be

adjusted automatically (CLOCK, PHASE, H-POS,

V-POS).

Note:

- When setting up this monitor for the first time or

after having changed an aspect of the current

system, perform an automatic screen adjustment

before use.

Automatic adjustment screen display

To perform an automatic adjustment, first display

an image that makes the entire screen very bright.

If you are using Windows, you can also use the

Adjustment Pattern on the accompanying Utility

Disk for Windows.

Displaying the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000/Me/XP,

and assumes that the floppy disk drive is [A drive].

Note:

- If the floppy disk drive of your computer is not

"A drive", please read the below substituting the

floppy disk drive you are using in place of

"A drive" or "A".

1. Place the Utility Disk (provided) into the

computer's A drive.

2. Open [My Computer] and select [3 ½ Floppy

(A:)]. If using Windows 3.1, open [File Manager]

and choose "A drive".

3. Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern will

appear.

Adjustment pattern

After completing the adjustment, press the

computer's [Esc] key to exit the Adjustment

Program.

Note:

- If your computer's display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the input signal

specification and is not a malfunction.)

Adjusting the screen display and speaker volume

02_LL-T17A3_gb.p65 9/13/2002, 2:37 PM17

Adjusting the screen automatically

1. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK

127

PHASE 16

POS

200

POS 29

1280X1024

V:60Hz H:64.0kHz

2. Press the button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3. Press the MENU button 4 times to make the On

Screen Display (OSD) Menu disappear.

Notes:

- In most cases automatic adjustment is sufficient.

- It may not be possible to achieve correct

adjustment with the first automatic adjustment. In

such a case, try repeating automatic adjustment

2 or 3 times.

- If necessary due to any of the following, manual

adjustments (right column) can be performed

after the automatic adjustment.

- When further fine adjustment is needed.

- When the computer’s video input signals are

Composite Sync or Sync On Green. (Automatic

adjustments may not be possible.)

- When [OUT OF ADJUST] is displayed. (When

the screen displays an entirely dark image, the

automatic screen adjustment may be disabled.

When making an automatic adjustment, be

sure to either use the Adjustment Pattern or try

displaying an image that makes the entire

screen very bright.)

- Automatic adjustment may not be achieved

correctly depending on what is displayed on the

screen - moving pictures or the MS-DOS prompt

etc.

Adjusting the screen display and speaker volume

Manual screen adjustment

Adjustments can be made using On Screen

Display (OSD) Menu provided.

1.Display an image that makes the entire screen

very bright. If using Windows, you can open and

use the Adjustment Pattern on the accompanying

Utility Disk. (p. 17)

2.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

ADJUSTMENT

MANUAL AUTO

CLOCK

127

PHASE 16

POS

200

POS 29

1280X1024

V:60Hz H:64.0kHz

At this point relevant menu options can be

adjusted.

Each time the MENU button is pressed the next

menu is selected. (ADJUSTMENT → GAIN

CONTROL → WHITE BALANCE → MODE

SELECT → OSD Menu disappears)

Notes:

- The OSD Menu automatically disappears

approximately 30 seconds after the last

command.

- This explanation is based on using the

Adjustment Pattern (for Windows) to make

adjustments.

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM18

EnglishDeutschFrançaisItalianoEspañolEnglish

ADJUSTMENT Menu

ADJUSTMENT

MANUAL AUTO

CLOCK

127

PHASE 16

POS

200

POS 29

1280X1024

V:60Hz H:64.0kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: / MODE button

- To go to the next menu: MENU button

CLOCK

The figure below demonstrates how to adjust so

that vertical flicker noise is not emitted. (

buttons)

PHASE

The figure below demonstrates how to adjust so

that horizontal flicker noise is not emitted. (

buttons)

Note:

- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS

(vertical positioning)

To center the screen image within the boundaries

of the screen, adjust the left-right (H-POS) values

and the up-down (V-POS) values. (

buttons)

Adjusting the screen display and speaker volume

Vertical flicker noise

Horizontal flicker noise

Screen frame

Adjustment

pattern

GAIN CONTROL Menu

GAIN

CONTROL

MANUAL AUTO

B L AC K

LEVEL

CONTRAST 66

1280X1024

V:60Hz H:64.0kHz

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted using the Auto Gain Control*

function.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option: / MODE button

- To go to the next menu: MENU button

* Auto Gain Control function

- The Auto Gain Control adjusts contrast and black

level based on the brightest color of the image

displayed. If you are not using the Adjustment

Pattern it is necessary to have an area of 5 mm x

5 mm of white displayed, and if not adjustments

may not be possible.

- If the signal coming from the computer is

composite sync or sync on green, automatic

adjustment cannot be performed. Please perform

manual adjustment instead.

- If [OUT OF ADJUST] is displayed, perform

manual adjustment.

- When using the Auto Gain Control function, set

[WHITE BALANCE] to other than [USER]. If

[USER] is set, the Auto Gain Control function

cannot be used.

BLACK LEVEL

Total screen brightness can be adjusted while

watching the color pattern. (

buttons)

CONTRAST

While watching the color pattern, adjustments can

be made so that all graduations appear. (

buttons)

Color pattern

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM19

WHITE BALANCE Menu

WHITE

BALANCE

COOL

STD

WARM

USER

CONTRAST

1280X1024

V:60Hz H:64.0kHz

Notes:

- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set

to [STD].

- If COLOR MODE is set to [sRGB] or [VIVID], no

other setting than [STD] can be selected.

- Use the

buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and [B-

CONTRAST], in order to make fine adjustments.

- Use the / MODE button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- To go to the next menu: MENU button

COOL ....... Color tone bluer than standard

• ............. Color tone slightly bluer than standard

STD .......... Color tone standard setting

• ............. Color tone slightly redder than standard

WARM ...... Color tone redder than standard

USER

R-CONTRAST .....

button for blue-green

button for red

G-CONTRAST .....

button for purple

button for green

B-CONTRAST .....

button for yellow

button for blue

Adjusting the screen display and speaker volume

MODE SELECT Menu

MODE

SELECT

OS D

POSITION

OS D

POSITION

SC AL I NG 3

INPUT VESA MAC

400

L I NES 640 720

L ANGUAGE

1280X1024

V:60Hz H:64.0kHz

Notes:

- Depending on the resolution of the input signal,

even if menu options can be selected, the display

may not change.

- To choose a menu option: / MODE button

- When adjustment complete: MENU button

OSD H-POSITION (OSD horizontal position)

The position of the OSD display can be moved to

the left and right. (

buttons)

OSD V-POSITION (OSD vertical position)

The position of the OSD display can be moved up

and down. (

buttons)

SCALING (Level of scaling)

The sharpness of the image can be adjusted. (

buttons)

Note:

- When the display mode is set to less than

1280 x 1024 pixels, the display is enlarged to

cover the whole screen (i.e. the side ratio of the

display may change).

INPUT

When connecting a Power Macintosh, set to [MAC].

(

buttons)

400 LINES (degree of resolution)

You can specify the horizontal resolution of a 400-

line screen when using US text, etc. (

buttons)

640: 640 X 400 dot mode

720: 720 X 400 dot mode (US text etc.)

Note:

- As the resolution input for other than 400 lines is

done automatically, there is no need to set it.

LANGUAGE

You can chose the language used in OSD Menu.

1. Press the

button.

The Language Selection Menu will be displayed

on the screen.

2. Use the / MODE button to choose a language.

3. Press the MENU button.

Language Selection Menu will disappear.

02_LL-T17A3_gb.p65 9/12/2002, 6:02 PM20

La pagina sta caricando ...

Sharp LL-T17A3 Manuale del proprietario

Marca: Sharp

Modello: LL-T17A3

Categoria: TV

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Sharp LL-T17A3 Owner's manual
français: Sharp LL-T17A3 Le manuel du propriétaire
español: Sharp LL-T17A3 El manual del propietario
Deutsch: Sharp LL-T17A3 Bedienungsanleitung

Sharp LL-T17A3 Manuale del proprietario

Sharp LL-T17A3 Manuale del proprietario

in altre lingue

Documenti correlati