Wolf ICBSRT364C-LP Manuale utente

SEALED BURNER RANGETOPS

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

33

ENGLISH 4

ESPÃNOL 18

FRANÇAIS 32

ITALIANO 46

DEUTSCH 60

As you follow these instruc tions, you will

noticeWARNING and CAUTION symbols. This

blocked information is impor tant for the safe

and efficient installation of Wolf equipment.

There are two types of potential hazards that

may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

5

WOLF SEALED BURNER RANGETOP

INSTALLATION REQUIREMENTS

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your

building.

Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

If you cannot reach your gas

supplier, call the fire department.

IMPORTANT NOTE:

Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

Do not store or use gasoline or

other flammable vapors and liquids

in the vicinity of this or any other

appliance.

The use of a gas cooking appliance

results in the production of heat and

moisture in the room in which it is

installed. Ensure that the kitchen is

well ventilated; keep natural ventila-

tion holes open or install a mechani-

cal ventilation device (mechanical

extractor hood)

Prolonged intensive use of the appli-

ance may for additional ventilation,

for example opening of a window,

or more effective ventilation, for

example increasing the level of

mechanical ventilation where

present.

This appliance shall be installed

in accordance with the regula-

tions in force and only used in a

well ventilated space. Read the

instructions before installing or

using this appliance.

6

WOLF SEALED BURNER RANGETOP

RATING PLATE

INFORMATION

Model Number

Serial Number

INSTALLATION REQUIREMENTS

IMPORTANT NOTE: This installation must

be completed by a qualified installer,

service agency or gas supplier.

IMPORTANT NOTE:

Save these Installation

Instructions for the local inspector’s use.

Please read the entire Installation Instruc-

tions prior to installation.

Installer:

please retain these instructions

for local inspector’s reference, then leave

them with the homeowner.

Homeowner:

please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

IMPORTANT NOTE:

This appliance must be

installed in accordance with local codes. The

correct voltage, frequency and amperage must

be supplied to the appliance from a dedicated,

grounded circuit which is protected by a

properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and

amperage ratings are listed on the product

rating plate.

Record the model and serial numbers before

installing the sealed rangetop. Both numbers

are listed on the rating plate, located on the

underside of the sealed rangetop. Refer to the

illustration below.

BEFORE YOU START

Proper installation is your responsibility.

Have a qualified technician install this

sealed rangetop. You must also assure that

electrical installation is adequate and in

compliance with all local codes and ordi-

nances.

Prior to installation, ensure that the local

distribution conditions (nature of the gas

and gas pressure) and the adjustment of

the appliance are compatible.

Proper gas supply connection must be

available; refer to Gas Supply Requirements

on page 12. Electrical ground is required;

see Electrical Requirements on page 15.

The adjustment conditions for this appli-

ance are stated on the label (or rating

plate). The data plate can be found on the

underside of the sealed rangetop.

Rating plate location

Location of rating plate

under control panel

7

INSTALLATION INSTRUCTIONS

BEFORE YOU START

Check the location where the rangetop will

be installed. The location should be away

from strong draft areas, such as windows,

doors and strong heating vents or fans. Do

not obstruct the flow of air. The area in

which you are installing this appliance must

have an adequate supply of fresh air to

ensure proper combustion and ventilation.

This appliance is not connected to a

combustion products evacuation device.

It shall be installed and connected in accor-

dance with current installation regulations.

Particular attention shall be given to the

relevant requirements regarding ventilation.

All openings in the wall where the rangetop

is to be installed must be sealed.

INSTALLATION SPECIFICATIONS

Wolf sealed burner rangetops come in

762 mm, 914 mm and 1219 mm widths. Illus-

trations on pages 9–11 provide the overall

dimensions and installation specifications for

each width of sealed burner rangetop.

Each rangetop is designed to fit between

cabinets set at the distance specified by the

unit. For example, a 914 mm rangetop will fit a

914 mm opening.

IMPORTANT NOTE:

Cabinet opening dimen-

sions shown in the Installation Specifications

illustrations must be used. These dimensions

provide for required clearances.

IMPORTANT NOTE:

Locate the electrical

supply within dimensions shown in the

Installation Specifications illustrations.

Refer to the Installation Specifications illustra-

tion for your model on pages 9–11 for the

exact rough opening dimensions and location

of the gas and electrical supply.

ISLAND | PENINSULA INSTALLATIONS

Minimum clearances to combustible

surfaces:

Island Installations: Minimum 305 mm

clearance to rear wall that rises above the

countertop.

Peninsula Installations: Minimum 152 mm

clearance to side walls and minimum

305 mm clearance to rear wall that rises

above the countertop.

Refer to the Installation Specifications

illustration for your model on pages 9–11

for the exact rough opening dimensions.

8

WOLF SEALED BURNER RANGETOP

MINIMUM CLEARANCES

IMPORTANT NOTE:

Caution must be used

in planning the proper installation of the Wolf

sealed burner rangetop to avoid fire or

damage to adjacent cabinetry or kitchen

equipment. Be sure to follow the minimum

clearances established in the finished rough

opening dimensions.

Refer to the Installation Specifications

illustration for your model on pages 9–11

for the exact rough opening dimensions.

WALL INSTALLATIONS

Minimum clearances to combustible

surfaces:

Minimum 457 mm clearance from bottom

of upper cabinet to countertop, within

152 mm minimum side clearance.

Minimum spacing between overhead side

cabinets must be greater than or equal to

the nominal width of the rangetop. The

maximum depth of overhead and side

cabinets is 330 mm, within 152 mm side

clearance.

0 mm clearance for adjacent combustible

materials below the countertop, both sides

and rear.

Bottom of ventilation hood must be

762 mm minimum to 914 mm maximum

from countertop.

Minimum clearances for sealed burner

rangetops without a ventilation hood:

Model ICBSRT304: 762 mm minimum

vertical distance from countertop to

combustible materials above the rangetop.

All Other Sealed Burner Rangetops:

Surface Burners or Griddle (G) Models:

914 mm minimum vertical distance from

countertop to combustible materials above

the rangetop.

Charbroiler (C) Models: 1118 mm minimum

vertical distance from countertop to

combustible materials above the rangetop.

Failure to locate the rangetop without

the proper clearances will result in a fire

hazard.

RISER REQUIREMENTS

Installations against a combustible surface:

Model ICBSRT304: No riser requirements.

914 mm Sealed Burner Rangetops: A

minimum 254 mm riser is required for all

charbroiler (C) or griddle (G) models

installed against a combustible surface.

1219 mm Sealed Burner Rangetops: A

minimum 254 mm riser is required for all

charbroiler (C) or griddle (G) models

installed against a combustible surface.

9

INSTALLATION INSTRUCTIONS

VENTILATION

HOOD

762 mm

OPENING WIDTH

762 mm min

TO

914 mm max

TO BOTTOM OF

VENTILATION HOOD

762 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

19 mm

PLATFORM

TOP VIEW

OF PLATFORM

E

G

406 mm

102 mm

BACK

WALL

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

914 mm

457 mm min

TO COUNTERTOP

19 mm

PLATFORM

216

mm

COOKING

SURFACE

191 mm

610 mm

330 mm

max

152 mm min

TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

759 mm

OVERALL WIDTH

616 mm

318

mm

WITH

127 mm

RISER

445

mm

WITH

254 mm

RISER

699

mm

WITH

508 mm

RISER

724 mm

OVERALL DEPTH

216 mm

OVERALL

HEIGHT

COOKING

SURFACE

191

mm

235

mm

INSTALLATION SPECIFICATIONS

OVERALL DIMENSIONS

Overall Width 759 mm

Overall Height

(to cooking surface) 216 mm

Overall Depth 724 mm

Opening Width 762 mm

Dimensions may vary to

±

3 mm.

762 mm SEALED BURNER RANGETOP

10

WOLF SEALED BURNER RANGETOP

VENTILATION HOOD

914 mm

FINISHED ROUGH OPENING WIDTH

762 mm min TO

914 mm max

TO BOTTOM OF

VENTILATION HOOD

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

1118 mm min

FOR CHARBROILER

19 mm

PLATFORM

TOP VIEW

OF PLATFORM

E

G

406 mm

102 mm

BACK

WALL

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

914 mm

457 mm min

TO COUNTERTOP

19 mm

PLATFORM

216

mm

COOKING

SURFACE

191 mm

610 mm

330 mm

max

152 mm min

TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

911 mm

OVERALL WIDTH

616 mm

724 mm

OVERALL DEPTH

216 mm

OVERALL

HEIGHT

COOKING

SURFACE

191

mm

235

mm

445

mm

WITH

254 mm

RISER

699

mm

WITH

508 mm

RISER

INSTALLATION SPECIFICATIONS

OVERALL DIMENSIONS

Overall Width 911 mm

Overall Height

(to cooking surface) 216 mm

Overall Depth 724 mm

Opening Width 914 mm

Dimensions may vary to

±

3 mm.

914 mm SEALED BURNER RANGETOP

IMPORTANT NOTE:

A minimum 254 mm

riser is required for

all charbroiler (C) or

griddle (G) models

installed against a

combustible surface.

11

INSTALLATION INSTRUCTIONS

VENTILATION HOOD

1219 mm

FINISHED ROUGH OPENING WIDTH

762 mm min TO

914 mm max

TO BOTTOM OF

VENTILATION HOOD

914 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

1118 mm min

FOR CHARBROILER

LOCATION OF GAS AND

ELECTRICAL SUPPLY CUT-OUT

WITHIN SHADED AREA

THROUGH BOTTOM OF

PLATFORM

19 mm PLATFORM

TOP VIEW

OF PLATFORM

E

G

406 mm

102 mm

BACK

WALL

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGETOP TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

914 mm

457 mm min

TO COUNTERTOP

19 mm

PLATFORM

216

mm

COOKING

SURFACE

191 mm

610 mm

330 mm

max

152 mm min

TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

1216 mm

OVERALL WIDTH

616 mm

724 mm

OVERALL DEPTH

216 mm

OVERALL

HEIGHT

COOKING

SURFACE

191

mm

235

mm

318

mm

WITH

127 mm

RISER

445

mm

WITH

254 mm

RISER

699

mm

WITH

508 mm

RISER

INSTALLATION SPECIFICATIONS

OVERALL DIMENSIONS

Overall Width 1216 mm

Overall Height

(to cooking surface) 216 mm

Overall Depth 724 mm

Opening Width 1219 mm

Dimensions may vary to

±

3 mm.

1219 mm SEALED BURNER RANGETOP

IMPORTANT NOTE:

For 1219 mm sealed

burner rangetops,

a minimum 254 mm

riser is required for

all charbroiler (C) or

griddle (G) models

installed against a

combustible surface.

12

WOLF SEALED BURNER RANGETOP

IMPORTANT

NOTE

This installation

must conform with

local codes and

ordinances.

INSTALL THE RANGETOP

Prepare the finished rough opening for the

rangetop according to the Installation Specifi-

cations illustration for your model on pages

9–11. The platform must be 19 mm thick and

include a cut-out at the right rear for gas

supply and electrical connections.

IMPORTANT NOTE:

The platform must be

level to ensure that the cooking surface is

level.

Remove and discard all packing materials,

including cardboard and tape on the outside of

the rangetop. Remove the burner grates and

styrofoam off the top cooking surface. Be

sure to remove the burner caps packaged in

styrofoam below the burner grates.

If your installation requires a riser, it must be

attached to the rangetop before installation.

Refer to the installation instructions packaged

with the riser.

Position the rangetop on the platform. Gas

supply and electrical connections should be

made before the rangetop is placed in its final

position.

IMPORTANT NOTE:

The sealed rangetop must

be connected to a regulated gas supply.

IMPORTANT NOTE:

This installation must

conform with local codes and ordinances.

The rating plate, located on the underside of

the burner box, has information on the type of

gas that should be used. If this information

does not agree with the type of gas available,

check with the local gas supplier.

An ISO 7-1 gas inlet thread is provided on all

units. Please contact your local Wolf dealer if

an ISO 228-1 or other gas inlet thread is

required. Pipe joint compounds, suitable for

use with LP gas should be used. LP gas suppli-

ers usually determine the size and materials

used on the system.

If local codes permit, a flexible metal appliance

connector is recommended for connecting this

sealed rangetop to the gas supply line. Do not

kink or damage the flexible connector when

moving the sealed rangetop. You will need to

determine the fittings required, depending on

the size of your gas supply line, flexible metal

connector and shut-off valve.

If rigid pipe is used as a gas supply line, a

combination of pipe fittings must be used to

obtain an in-line connection to the sealed

rangetop. All strains must be removed from

the supply and gas lines so the sealed

rangetop will be level and in line.

EXPLOSION HAZARD—

Securely tighten all external gas

connections.

Failure to do so can result in explosion,

fire or death.

GAS SUPPLY REQUIREMENTS

13

INSTALLATION INSTRUCTIONS

GAS RATING

Total Heat Electrical Types and

Output Gas Rating Appliance Pressures

Model # (Gas) Units (Amps) Category (mbar) Country of Destination

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT304 16.6 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT304-LP 1037 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT364C 22.4 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT364C-LP 1415 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT364G 22.1 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT364G-LP 1373 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT486C 31.6 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT486C-LP 1987 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT486G 31.3 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT486G-LP 1945 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT484CG 27.9 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT484CG-LP 1751 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

I2H G20 at 20

AT, DK, EE, FI, GR, IE, IT, LT,

ICBSRT484F 21.2 kW 0.17

NO, PT, ES, SE, SI, SK, GB, CH

I2E G20 at 20 DE, PL

I2E+ G20 at 20/25 BE, FR

ICBSRT484F-LP 1323 g/h 0.17 I3P G31 at 37

BE, CZ, FR, GR, IE, NL, NO,

PT, ES, GB, CH

GAS SUPPLY REQUIREMENTS

GAS LEAK TESTING

Use a brush and liquid detergent to test all gas

connections for leaks. Bubbles around connec-

tions will indicate a leak. If a leak appears, shut

off the gas valve and adjust connections. Then

check connections again. Clean all the deter-

gent solution from the rangetop.

14

WOLF SEALED BURNER RANGETOP

Never test for a gas leak with a match or

other flame.

15

INSTALLATION INSTRUCTIONS

ELECTRICAL REQUIREMENTS

ELECTRICAL SHOCK HAZARD—

Plug into a grounded 3-prong adapter.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can

result in electric shock, fire or death.

RECOMMENDED GROUND METHOD

IMPORTANT NOTE:

For your personal safety,

this sealed rangetop must be grounded. This

sealed rangetop is equipped with a 3-prong

ground plug. To minimize possible shock

hazard, the cord must be plugged into a

mating 3-prong ground-type outlet, grounded

in conformance with all local codes and ordi-

nances. If a mating outlet is not available, it is

the obligation of the customer to have a

properly grounded, 3-prong outlet installed by

a qualified electrician.

IMPORTANT NOTE:

If product is connected to

a GFCI protected outlet, nuisance tripping of

power supply may occur, resulting in loss of

product operation.

WIRING DIAGRAM

The wiring diagram covering the electrical

circuit is located on the inside left wall of the

rangetop.

IMPORTANT NOTE:

If codes permit and a

separate ground wire is used, it is recom-

mended that a qualified electrician determine

that the ground path is adequate.

IMPORTANT NOTE:

Check with a qualified

electrician if you are not sure whether the

sealed rangetop is properly grounded.

IMPORTANT NOTE:

Do not ground to a gas

pipe.

A 220-240 VAC, 50/60 Hz, fused electrical

supply is required. A time-delay fuse or circuit

breaker is recommended. It is recommended

that a separate circuit serving only this appli-

ance be provided.

Electronic ignition systems operate within

wide voltage limits, but proper ground and

polarity are necessary. In addition to checking

that the outlet provides 220-240 VAC power

and is correctly grounded, the outlet must be

checked by a qualified electrician to see if it is

wired with correct polarity.

This appliance, when installed, must be electri-

cally grounded in accordance with local codes.

16

WOLF SEALED BURNER RANGETOP

SURFACE BURNERS

INITIAL LIGHTING

The surface burners use electronic igniters in

place of standing pilots. When the sealed

rangetop control knob is pushed in and turned

to the position, the system creates a spark

to light the burner. This sparking continues

until the electronic ignition senses a flame. If

the burner fails to ignite after 10 seconds,

return the knob to the position and attempt

to ignite by turning the knob back to the

position.

Be sure to place the burner heads and caps on

each burner base and position the burner

grates over the burner bases and heads before

lighting.

To check operation of the surface burners,

push in and turn each control knob to the

position. The flame should light within four

seconds.

If the burners do not light properly, turn

control knob to the position. Check that the

burner heads and caps are in the proper

position. Check that the power supply cord is

plugged in and that the circuit breaker or

house fuse has not blown. Check operation

again, if the burners do not light properly at

this point, contact a Wolf authorized service

center.

IMPORTANT NOTE:

Initial lighting of the

surface burners may take slightly longer, as air

in the system must be purged before gas can

be supplied to the burner.

SEALED RANGETOP REMOVAL

If it is necessary to remove the sealed

rangetop for cleaning or service, shut off the

gas supply. Disconnect the gas and electric

supply. Remove the mounting brackets on the

right and left side of the burner box and

remove the sealed rangetop. Reinstall in the

reverse order and check the gas connection for

leaks.

TROUBLESHOOTING

IMPORTANT NOTE:

If the sealed rangetop

does not operate properly, follow these trou-

bleshooting steps:

Verify that power is being supplied to the

sealed rangetop.

Check that gas valves are turned to the ON

position.

Check the gas supply and electrical

connections to ensure that the installation

has been completed correctly.

Follow troubleshooting procedures as

described in the Wolf Sealed Burner

Rangetops Use & Care Information.

If the sealed rangetop still does not work,

contact a Wolf authorized service center. Do

not attempt to repair the sealed rangetop

yourself. Wolf is not responsible for service

required to correct a faulty installation.

17

CONTACT

INFORMATION

Website:

wolfappliance.com

IF YOU NEED SERVICE

For service in your area, contact either your

Wolf dealer or visit the Showroom Locator

section of our website, wolfappliance.com

to find the regional distributor by country.

When calling for service, you will need the

sealed rangetop model and serial numbers.

Both numbers are listed on the rating plate,

located on the underside of the sealed

rangetop. Refer to the illustration on page 6

for location of the rating plate.

INSTALLATION INSTRUCTIONS

The information and images in this book are the

copyright property of Wolf Appliance, Inc., an

affiliate of Sub-Zero, Inc. Neither this book nor any

information or images contained herein may be

copied or used in whole or in part without the

express written permission of Wolf Appliance,

Inc.,an affiliate of Sub-Zero, Inc.

Cuando consulte las instrucciones que aparecen

en esta guía, encontrará símbolos de ADVER-

TENCIA y PRECAUCIÓN. Esta información en

recuadros es importante para instalar el equipo

de Wolf de forma segura y eficaz. Existen dos

tipos de posibles riesgos que pueden producirse

durante una instalación.

Otro tipo de anotación que es importante

resaltar es la que se incluye en NOTA

IMPORTANTE: En esta nota se resalta la

información que resulta especialmente

importante para que la instalación se

realice sin problemas.

PRECAUCIÓN

indica una situación en la que se pueden sufrir

heridas leves o provocar daños secundarios al

producto si no se siguen las instrucciones.

indica peligro de que se produzcan heridas

personales graves o incluso puede provocar

la muerte si no se siguen las precauciones

especificadas.

WOLF

®

es una marca comercial registrada de Wolf Appliance, Inc.

INFORMACIÓN

DE CONTACTO

Página Web:

www.sub-zero.eu.com

19

ENCIMERA DE COCCIÓN A GAS CON QUEMADORES HERMÉTICOS DE WOLF

REQUISITOS DE

INSTALACIÓN

QUÉ SE DEBE HACER SI HUELE A GAS:

No encienda ningún aparato.

No toque ningún interruptor

eléctrico.

No utilice ningún teléfono dentro

del edificio.

Llame inmediatamente a su

proveedor de gas desde el teléfono

de un vecino. Siga las instrucciones

que le proporcione el proveedor

de gas.

Si no le es posible ponerse en

contacto con el proveedor de

gas, llame a los bomberos.

NOTA IMPORTANTE:

La instalación y el mantenimiento

deben ser realizados por un instalador

cualificado, por un centro de asisten-

cia técnica o por el proveedor de gas.

No almacene ni utilice gasolina ni

otros vapores ni líquidos inflamables

cerca de éste o de otros aparatos.

La utilización de un aparato de

cocción de gas produce calor y vaho

en la habitación en la que está instal-

ado. Asegúrese que la cocina está

bien ventilada; mantenga despejados

los agujeros de ventilación natural o

instale un dispositivo de ventilación

mecánico (campana extractora

mecánica).

Si utiliza mucho el aparato y lo hace

de manera prolongada, es posible que

necesite ventilación adicional, por

ejemplo, puede abrir una ventana,

o si quiere que la ventilación sea

más eficaz, aumente el nivel de la

ventilación mecánica, si dispone

de ella.

Este aparato debe instalarse de

acuerdo con las normativas vigentes

y sólo puede ser utilizado en un lugar

que esté bien ventilado. Lea las

instrucciones antes de instalar

o utilizar este aparato.

20

ENCIMERA DE COCCIÓN A GAS CON QUEMADORES HERMÉTICOS DE WOLF

INFORMACIÓN

DE LA PLACA

DE DATOS

Referencia del

modelo

Número de serie

REQUISITOS DE INSTALACIÓN

NOTA IMPORTANTE: Esta instalación debe ser

realizada por un por un instalador cualificado,

por un centro de asistencia técnica o por el

proveedor de gas.

NOTA IMPORTANTE: Guarde estas instrucciones

de instalación para que el inspector local pueda

utilizarlas.

Lea las instrucciones de instalación antes

de llevar a cabo la instalación.

Instalador: guarde estas instrucciones para

que el inspector local pueda utilizarlas como

referencia y, a continuación, entréguelas al

propietario del aparato.

Propietario: lea y guarde estas instrucciones

para que pueda utilizarlas como referencia en

el futuro y asegúrese de leer la guía de uso

y mantenimiento antes de utilizar el aparato.

NOTA IMPORTANTE: Este aparato debe instalarse

siguiendo las normativas nacionales

correspondientes. Se debe aplicar al aparato

el voltaje, la frecuencia y el amperaje adecuados

desde una instalación eléctrica resistente con

toma de tierra protegida por un fusible de

retardo. El voltaje, la frecuencia y el amperaje

se muestran en la placa de datos del producto.

Apunte la referencia del modelo y el número de

serie antes de instalar la encimera de cocción con

quemadores herméticos. Esta información se

muestra en la placa de datos del producto situada

en la parte inferior de la encimera de cocción con

quemadores herméticos. Observe la siguiente

ilustración.

ANTES DE COMENZAR

Es responsabilidad del propietario asegurarse

de que la instalación se realiza de manera

correcta. Esta encimera de cocción con

quemadores herméticos debe ser instalada

por un técnico cualificado. Debe asegurarse

de que la instalación eléctrica es la correcta

y que cumple todos los códigos y normativas

nacionales.

Antes de llevar a cabo la instalación,

asegúrese de que las condiciones de

distribución locales (tipo y presión del gas)

y el ajuste del aparato son compatibles.

Debe disponer de una entrada de suministro

de gas; consulte la sección Requisitos del

suministro de gas en la página 26. También

debe disponer de una conexión eléctrica a

tierra; consulte la sección Requisitos eléctricos

en la página 29.

Las condiciones de ajuste de este aparato se

especifican en la etiqueta (o en la placa de

datos del producto). La placa de datos está

ubicada en la parte inferior de la encimera

de cocción con quemadores herméticos.

Ubicación de la placa de datos

Ubicación de la placa de

datos del panel de mandos

La pagina sta caricando ...

Wolf ICBSRT364C-LP Manuale utente

Wolf ICBSRT364C-LP Manuale utente

in altre lingue

Documenti correlati

Altri documenti