Juki MO-734DE Manuale del proprietario

Marca: Juki

Modello: MO-734DE

Tipo: Manuale del proprietario

Instruction Manual

Manual de instrucciones

Manuel d’instructions

Manuale d'istruzioni

MO-734DE

2-Needle, 2/3/4-Thread Overlock Sewing Machine

Maquina de coser Sobreorilladora de 2 Agujas, 2/3/4 Hilos

Surjeteuse-Raseuse 2 Aiguilles, 2/3/4 Fils

Macchina per cucire surfilatrice 2 aghi, 2/3/4 fili

IMPORTANTE:

Prima della messa in servizio, leggere e seguire con

attenzione tutte le regole per la sicurezza.

Conservare e consultare questo manuale per ogni

riferimento futuro.

IMPORTANTE:

Lea cuidadosamente todas las recomendaciones

con respecto a la seguridad y comprendalas

perfectamente antes de usar su maquina.

Guarde este libro de instrucciones para referencias

futuras.

IMPORTANT:

Read all safety regulations carefully and understand

them before using your sewing machine.

Retain this instruction manual for future reference.

IMPORTANT:

Avant de mettre la machine en marche, lire

attentivement et assimiler les regles de securite de

ce manuel.

Conserver le manuel afin de pouvoir le consulter ul

terieurement.

“IMPORTANT SAFETY INSTRUCTIONS”

When using an electrical appliance, basic safety precautions should always be followed, including the following: Read all instructions before using

this overlock sewing machine.

“DANGER_____To reduce the risk of electric shock:”

1. The appliance should never be left unattended when plugged in.

2. Always unplug this appliance from the electric outlet immediately after using and before cleaning.

3. Always unplug before re-lamping. Replace bulb with same type rated max. 12V / 5W for model MO-734DE.

“WARNING_____To reduce the risk of burns, fire, electric shock, or injury to persons:”

1. Do not allow this appliance to be used as a toy. Close attention is necessary when this appliance is used by or near children and infirm

persons.

2. Use this appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as

contained in this manual.

3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped

into water. Return the appliance to the nearest authorized dealer or service center for examination, repair, electrical or mechanical

adjustment.

4. Never operate the appliance with any air openings blocked. Keep ventilation openings of the sewing machine and foot control free from

the accumulation of lint, dust, and loose cloth.

5. Keep fingers away from all moving parts. Special care is required around the sewing machine needle and knife.

6. Always use the proper stitch plate. The wrong plate can cause the needle to break.

7. Do not use bent needles.

8. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

9. Switch the sewing machine off ''O'' when making any adjustments in the needle area, such as threading needle, changing needle,

threading looper, or changing presser foot and the like.

10. Always unplug the machine from the electrical outlet when removing covers, when covers are opened to raise the knife or thread the

loopers, when lubricating or when making any other user servicing adjustments mentioned in the instruction manual.

11. Never drop or insert any object into any opening.

12. Do not use outdoors.

13. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

14. To disconnect, turn all controls to the off ''O'' position, then remove plug from outlet.

15. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

16. Basically, the machine should be disconnected from the electricity supply when not in use.

17. If the power cord of this appliance is damaged, it must be replaced with a special cord by your nearest authorized dealer or service

center.

18. This appliance is provided with double insulation. (except USA/CAN)

Use only identical replacement parts. See instructions for servicing double insulated appliances.

19. If oil gets in eyes, immediately, rinse the oil out with water. If you swallow oil by mistake, immediately consult a medical doctor.

“SERVICING DOUBLE-INSULATED PRODUCTS

(USA and Canada version excepted)”

In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated

product nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and knowledge

of the system and should only be done by qualified service personnel. Replacement parts for a double-insulated product must be identical to those

parts in the product. A double-insulated product is marked with the words DOUBLE INSULATION or DOUBLE INSULATED.

The symbol may also be marked on the product.

“SAVE THESE INSTRUCTIONS”

''This overlock sewing machine is intended for household use only.''

“NORMAS DE SEGURIDAD IMPORTANTES”

Cuando se usa un aparato eléctrico deben respetarse las siguientes normas de seguridad:

“PELIGRO_____para reducir el riesgo de electrochoque:”

1. No dejar nunca la máquina de punto cadeneta y cobertura sin vigilancia si ella está enchufada.

2. Después de coser y antes de los trabajos de mantenimiento, la máquina debe desconectarse quitando el enchufe de la red eléctrica.

3. Antes de cambiar la bombilla, desenchufar la máquina. Usar solamente bombillas de 12 voltios, 5 vatios.

“ADVERTENCIA_____para reducir el riesgo de quemaduras, fuego, electrochoque o el riesgo

de herir personas:”

1. La máquina de punto cadeneta y cobertura no es ningún juguete. Tener mayor cuidado si la máquina la usan los niños o si se usa cerca

de ellos.

2. Usar esta máquina para los fines descritos en esta guía. Usar únicamente los accesorios recomendados por el fabricante.

3. No trabajar con esta máquina si el cable o el enchufe están dañados, ella no funciona bien o está estropeada, si se ha dejado caer al

suelo o dentro del agua. Llevar inmediatamente la máquina al próximo representante Bernina o al especialista correspondiente par

controlarla y/o arreglarla.

4. No bloquear las aperturas de refrigeración durante el uso de la máquina. Mantener estas aperturas abiertas, sin residuos o restos de

ropa.

5. No acercar nunca los dedos a las partes móviles, sobre todo cerca de la aguja.

6. Usar siempre una placa-aguja original. Una placa-aguja falsa puede romper la aguja.

7. No usar agujas torcidas.

8. Durante la costura, ni tirar de la ropa ni empujarla. Esto podría romper la aguja.

9. Las manipulaciones en la zona de la aguja, por ejemplo, enhebrar, cambiar la aguja o un pie prensatelas, etc. siempre deben hacerse

con el interruptor principal a "O".

10. Antes de los trabajos de mantenimiento descritos en la guía, como p.ej. limpieza, enhebrado de la lanzadera, cambio de bombillas, etc.

debe desconectarse la máquina quitando el enchufe de la red eléctrica.

11. No meter ningunos objetos dentro de las aperturas de la máquina.

12. No usar la máquina al aire libre.

13. No usar la máquina en sitios donde se utilizan productos con gas propelentes (sprays) u oxígeno.

14. Para desconectar la máquina, colocar el interruptor principal a "O" y quitar el enchufe de la red.

15. Desenchufar de la red tirando siempre del enchufe y no del cable.

16. Generalmente, cuando la máquina no se usa tiene que desconectarse quitando el enchufe de la red eléctrica.

17. Si el cable eléctrico está dañado, entonces hay que cambiarlo por uno nuevo original. Consultar el representante más cercano o el

centro de servicio para que lo cambien.

18. Si le entra aceite en los ojos,lávese inmediatamente con agua hasta que salga todo el aceite.el aceite. Si traga aceite por descuido,

consulte inmediatamente con un médecin.

“MANTENIMIENTO DE PRODUCTOS DE ISOLACION

DOBLE”

Un producto de aislamiento doble tiene dos unidades de aislamiento en vez de una toma de tierra. En un producto de aislamiento doble no hay una

toma de tierra, y tampoco debe incluirse una. El mantenimiento de un producto de aislamiento doble requiere mucha atención y conocimiento del

sistema. Pos eso sólo un especialista puede hacer este trabajo de mantenimiento. Usar únicamente piezas de recambio originales. Un producto de

aislamiento doble está marcado con: "Doble isolación" o "Isolación doble".

El símbolo puede también indicar semejante producto.

¡GUARDE BIEN ESTAS NORMAS DE SEGURIDAD!

Esta máquina de punto cadeneta y cobertura está solamente destinada para el uso doméstico.

“PRESCRIPTIONS DE SECURITE IMPORTANTES”

L’emploi d’un appareil électrique exige d’observer les mesures de sécurité suivantes:

“DANGER_____Pour la protection contre tout choc électrique:”

1. Ne pas laisser la surjeteuse sans surveillance tant qu’elle est raccordée au réseau.

2. Après usage et avant un nettoyage, séparer toujours la machine du réseau.

3. Retirer la fiche du réseau pour changer une ampoule. Employer des ampoules pour modèle MO-734DE: max. 12V / 5W.

“ATTENTION_____Pour éviter des brûlures, un feu, un choc électrique ou des blessures de

personnes:”

1. Ne pas prendre la surjeteuse pour un jouet. La plus grande prudence est de mise quand la machine est utilisée par des enfants ou se

trouve à leur proximité.

2. Utiliser la surjeteuse seulement dans le but d’accomplir les travaux décrits dans ce mode d’emploi. N’employer que les accessoires

recommandés par le fabricant.

3. Ne pas employer la surjeteuse, si les cordons ou les prises sont abîmés, si elle ne fonctionne pas sans problèmes, si elle est tombée par

terre ou dans l’eau, ou bien a été endommagée. Apporter votre surjeteuse pour réparation ou vérification auprès de l’agent le plus

proche ou du spécialiste correspondant.

4. Durant l’emploi de la surjeteuse, ne pas boucher les fentes d’aération ainsi que la pédale par des bouts de fil, de la poussière et des

déchets de tissu.

5. Eloigner les doigts de toute pièce en mouvement. Une prudence toute particulière s’impose à proximité des aiguilles et des couteaux

de la surjeteuse.

6. Utiliser toujours la plaque à aiguille originale de la surjeteuse. Une plaque erronée peut provoquer la cassure de l’aiguille.

7. Ne pas utiliser d’aiguilles courbées.

8. Durant la couture, ne pas tirer sur le tissu, ni le pousser, cela peut provoquer la cassure de l’aiguille.

9. Placer l’interrupteur principal sur «O» lors de toute activité à proximité des aiguilles, par ex. pour enfiler, changer d’aiguille ou de

pied-de-biche, etc.

10. Prière de toujours retirer la prise du réseau lorsque vous effectuez, sur la surjeteuse ouverte, des travaux d’entretien mentionnés dans

le mode d’emploi, comme l’enfilage des boucleurs, le relèvement du couteau, l’huilage, le changement des ampoules, etc.

11. Ne pas introduire d’objets dans les ouvertures de la machine.

12. Ne pas employer la surjeteuse en plein air.

13. Ne pas employer la surjeteuse dans un local où l’on utilise des produits avec gaz propulseur (spray) ou de l’oxygène.

14. Pour la mise hors service, placer le commutateur principal sur «O» et retirer la fiche du réseau.

15. Débrancher en tirant sur la fiche et non sur le cordon.

16. En cas de non utilisation, l’appareil doit, en principe, être séparé du réseau en retirant la prise.

17. Si le câble électrique est endommagé, il doit être remplacé par un câble original chez l’agent le plus proche ou dans un centre du service

après-vente.

18. Si de I’huile vient en cntact avec les yeux, les rincer immëdiatement avec de I’eau. En cas d’absorption accidentelle d’huile,

consulter immëdiatement un mëdecin.

“ENTRETIEN DES PRODUITS A DOUBLE ISOLATION ”

Un produit à double isolation est équipé de deux isolations au lieu d’une mise à la terre. La mise à la terre n’est pas prévue sur un produit à double

isolation et ne devrait donc pas être employée. L’entretien d’un produit à double isolation qui exige de grands soins et des connaissances poussées

sur le système, doit donc être réalisé seulement par du personnel qualifié. N’employer que des pièces de rechange originales pour l’entretien et la

réparation. Un produit à double isolation est désigné de la manière suivante: “Isolation double” ou “A double isolement”.

Le symbole peut également caractériser un tel produit.

“PRIERE DE CONSERVER SOIGNEUSEMENT LES

PRESCRIPTIONS DE SECURITE”

Cette surjeteuse est destinée seulement à un usage familial.

“ISTRUZIONI IMPORTANTI RIGUARDO LA SICUREZZA”

Usando una apparecchiatura elettrica bisogna osservare le seguenti prescrizioni di sicurezza di base:

“PERICOLO_____Per ridurre il rischio di scosse elettriche:”

1. Non lasciare mai la macchina tagliacuce incustodita, finche e collegata alla corrente elettrica.

2. Al termine del lavoro e prima di pulirla, staccare sempre la spina dalla presa di corrente.

3. Prima della sostituzione della lampadina staccare la spina dalla presa di corrente.Usare solo le lampadine : MO-734DE (massimo 10W , 220V)

“AVVERTIMENTI_____Per evitare incidenti come bruciature, fuoco, scosse elettriche e ferite,

osservare i seguenti punti:”

1. Non usare la macchina tagliacuci come giocattolo. E' richiesta una prudenza maggiore se la macchina viene usata nelle vicinanze di bambini,

oppure da bambini stessi.

2. Usare la macchina tagiacuce solamente come mezzo per ottenere lo scopo spiegato in questo libretto d'istruzioni. Usare solo gli accessori

originali raccomandati dal produttore.

3. Non usare la macchina tagliacuce, se il cavo o la spina sono difettosi, se la macchina cuce con problemi, se la macchina è caduta o danneggiata

oppure se la macchina è caduta in acqua. Portare la macchina tagliacuci dal rivenditore JUKI o dallo specialista per farla revisionare oppure

riparare.

4. Fare attenzione di non bloccare le fessure della ventilazione e proteggerle da laniccio, polvere e residui di stoffa.

5. Tenere lontano le mani da tutti i pezzi in movimento. Prestare particolare prudenza nelle vicinanze degli aghi e dei coltelli della taglaicuci.

6. Usare sempre una placca d'ago originale per tagliacuci JUKI. Una placca d'ago sbagliata può provocare la rottura degli aghi.

7. Non usare aghi storti o curvati.

8. Durante la cucitura non tirare ne spingere la stoffa, questo può provocare la rottura degli aghi.

9. Durante le operazioni manuali nella zona di movimento aghi, quali infilatura degli aghi e sostituzione aghi o piedino, disinserire la macchina.

10. Durante le operazioni di manutenzione spiegate in questo libretto d'istruzionicome per es. la lubrificazione o la sostituzione delle lampadine ecc.,

staccare sempre la macchina tagliacuci dalla rete elettrica, estarendo la spina dalla presa elettrica.

11. Non introdurre degli oggetti nelle aperture della macchina.

12. Non usare la macchina tagliacuce all'aria aperta.

13. Non usare la macchina tagliacuce in un locale dove vengono usati dei prodotti contenenti del gas (per es. bombolette spry) o dell'ossigeno.

14. Per disinserire la macchina tagliacuci mettere l'interruttore principale su "0" e togliere la spina dalla presa di corrente.

15. Per staccare la macchina dalla corrente, tirare sempre la spina, mai il cavo.

16. Se la macchina non viene usata, staccarla sempre dalla rete elettrica, estraendo la spina dalla presa elettrica.

17. Se il cavo elettrico è difettoso, deve essere sostituito con un cavo originale, che è disponibile dal vostro rivenditore JUKI.

18. Questa macchina è provvista di un doppio isolamento. Sostituire le parti solamente con uguali ricambi originali.

19. Se l'olio raggiunge per errore gli occhi, lavare gli stessi abbondantemente con acqua. Nel caso l'olio venisse ingerito per errore, consultare

immediatamente un medico.

“MANUTENZIONE DI PRODOTTI CON DOPPIO

ISOLAMENTO”

Un prodotto con doppio isolamento è dotato di due unità di isolamento invece di una presa di terra. Il prodotto con doppio isolamento richiede una

manutenzione precisa ed una buona conoscenza del sistema. Per questo motivo la manutenzione di questi prodotti deve essere effettuata

unicamente da personale qualificato. Per servizio e riparazione usare solo pezzi di ricambio originali. Un prodotto con doppio isolamento è

contrassegnato con la scritta :"Isolamento doppio".

Il prodotto può portare anche il simbolo:

“SI PREGA DI CONSERVARE CON CURA QUESTE

PRESCRIZIONI DI SICUREZZA”

Questa macchina tagliacuce e destinata al solo uso domestico.

Contents / Indice

Safety regulations ·························································· 1

Contents ········································································ 5

Details of the machine ··················································· 7,8

• Accessories ······························································· 8

Preparing the machine ··················································· 9

• Attaching the foot control ············································· 9

• Thread stand ······························································ 10

• Thread, cones, spools ················································ 11

Using the machine

• Main Power/ light switch ············································ 12

• Raising the upper knife ·············································· 12

• Changing the presser foot ·········································· 13

• Looper cover ······························································ 14

• Cloth plate ································································· 14

• Handwheel ································································· 14

• Inserting needles / Needles and Threads ················· 15-17

Adjustments and settings

• Stitch length ······························································ 18

• Cutting width ······························································ 18

• Differential feed ··························································· 19

• Gathering ··································································· 20

• Upper looper converter ················································ 21

• Roll hemming ····························································· 21

• Presser foot pressure ················································· 22

• Sewing in tape ··························································· 22

Setting/ Practical sewing

• Thread breakage ························································· 23

• Unpicking seams ······················································· 23

• Preparation/Tips ·························································· 24

Stitch chart ···································································· 25

Threading 4/3 Thread OL

• Upper looper ······························································ 29

• Lower looper ······························································ 30

• Right needle ······························································· 31

• Left needle ································································· 32

Trial sewing, thread tension ······································ 33-35

Practical Sewing-Overlock ··········································· 36,37

Maintenance

• Changing the upper knife ············································ 38

• Changing the lower knife ············································ 38

• Replacing the bulb ····················································· 39

• Cleaning and lubricating ············································· 39

Trouble shooting guide ··················································· 40

Technical data ································································ 40

Optional accessories ······················································ 44

Reglas de seguridad ······················································ 2

Indice ············································································· 5

Detalles de la máquina ·················································· 7,8

• Accesorios ································································· 8

Preparación de la máquina / puesta en servicio ················· 9

• Conexión del pedal de mando ······································ 9

• Guía-hilo ····································································· 10

• Colocación de bobinas ··············································· 11

Puesta en servicio

• Interruptor principal y de la luz ···································· 12

• Subir / bajar la cuchilla superior ·································· 12

• Cambio del prensatelas ·············································· 13

• Tapa de la lanzadera ·················································· 14

• Tapa de la mesa de trabajo ········································ 14

• Volante ······································································· 14

• Colocar agujas / Agujas / Hilo ································ 15-17

Regulación y manejo

• Largo del punto··························································· 18

• Posición de la cuchilla ··············································· 18

• Transporte diferencial ·················································· 19

• Fruncido ····································································· 20

• Transformador lanzadera ciega superior ······················ 21

• Dobladillo enrollado ····················································· 21

• Presión del prensatelas: ············································· 22

• Coser cinta ································································ 22

Manejo, costura práctica

• El hilo se rompe durante la costura ····························· 23

• Deshacer puntos: ······················································· 23

• Preparación del enhebrado / consejos ························ 24

Tabla de puntos ····························································· 26

Enhebrado de overlock de 4/3 hilos

• Hilo de la lanzadera superior ······································ 29

• Hilo de la lanzadera superior ······································ 30

• Aguja derecha ···························································· 31

• Aguja izquierda ··························································· 32

Costura de prueba, Tensión del hilo ··························· 33-35

Costura práctica: overlock ··········································· 36,37

Mantenimiento

• Atención! Observar las normas de seguridad ··············· 38

• Cambio de la cuchilla inferior ······································ 38

• Cambio de la bombilla ··············································· 39

• Limpieza y engrase ···················································· 39

Ayuda en caso de averías ············································· 41

Especificónes ································································· 41

Accesorios opcionales ··················································· 44

Table des matières / Indice

Uso, Cucito pratico

• Rottura del filo durante la cucitura ································ 23

• Disfare i punti ····························································· 23

• Preparazione dell'infilatura / Consigli ···························· 24

Tabella dei punti / Selezione ·········································· 28

Infilatura punto overlock a 3/4 fili

• Filo del crochet superiore ············································ 29

• Filo del crochet inferiore ·············································· 30

• Ago destro ·································································· 31

• Ago sinistro ································································· 32

Prova di cucito/Regolazione tensione del filo ·············· 33-35

Prova di cucito overlock ················································ 36,37

Manutenzione

• Attenzione:Osservare attentamente le prescr.di

sicurezza ····································································· 38

• Sostituzione del coltello superiore ······························· 38

• Sostituzione del coltello inferiore ·································· 38

• Sostit. della lampadina/Pulizia e lubrificazione ·············· 39

Eliminazione dei difetti ··················································· 43

Dati tecnici ···································································· 43

Accessori opzionali ························································ 44

Couture pratique

• Cassure du fil durant la couture ·································· 23

• Découdre une couture ················································ 23

• Préparer l’enfilage / conseils ······································· 24

Récapitulation des points ··············································· 27

Enfilage du point de surjet à 4/3 fils

• Fil de boucleur supérieur ············································ 29

• Fil de boucleur inférieur ············································· 30

• Aiguille de droite ························································ 31

• Aiguille de gauche ······················································ 32

Essai de couture, tension de fil ································· 33-35

Couture practique avec surjet ······································ 36,37

Maintenance

• Attention: respecter les prescriptions de sécurité ········· 38

• Remplacement du couteau inférieur ···························· 38

• Remplacement de l’ampoule ······································· 39

• Nettoyage et huilage ·················································· 39

Comment éliminer soi-même les pannes ························ 42

Caractéristiques ····························································· 42

Accessoires spéciaux ···················································· 44

Consignes de sécurité ··················································· 3

Table des matières ························································ 6

Détails de la machine ···················································· 7,8

• Accessoires ······························································· 8

Préparation de la machine / mise en service ····················· 9

• Raccordement de la pédale ········································· 9

• Guide-fil ······································································ 10

• Mise en place des bobines de fil ································· 11

Mise en service

• Commutateur principal et interrupteur de lumière ········· 12

• Remplacement du pied-de-biche ································· 13

• Couvercle du boucleur ················································ 14

• Plateau de travail ······················································· 14

• Volant ········································································ 14

• Relever et abaisser le couteau supérieur ····················· 12

• Mettre les aiguilles en place / Aiguilles / Fill ············· 15-17

Réglage et utilisation

• Longueur de point ······················································ 18

• Position du couteau ··················································· 18

• Entraînement différentiel ·············································· 19

• Fronçage ···································································· 20

• Recouvrement du boucleur supérieur ·························· 21

• Ourlets roulés ···························································· 21

• Pression du pied-de-biche ·········································· 22

• Pose de ruban ··························································· 22

Prescrizioni di sicurezza ················································ 4

Indice ············································································· 6

Dettagli della macchina ·················································· 7,8

• Accessori ···································································· 8

Preparazione della macchina/messa in servizio ················ 9

• Collegamento del reostato ············································ 9

• Asta guidafilo ······························································ 10

• Spolette normali ·························································· 11

Uso della macchina

• Interruttore principale e illuminazione/alzare coltello sup. 12

• Sostituzione del piedino ·············································· 13

• Coperchio del crochet ················································· 14

• Piano appoggia stoffa ·················································· 14

• Volantino ····································································· 14

• Int. principale/luce-alzare il coltello superiore ················ 12

• Sostituzione degli aghi / ago / filo ···························· 15-17

Regolazione ed uso

• Lunghezza del punto ··················································· 18

• Larghezza del taglio ···················································· 18

• Trasporto differenziale ·················································· 19

• Arricciatura ·································································· 20

• Copertura del crochet superiore ··································· 21

• Orlo arrotolato ····························································· 21

• Pressione del piedino ·················································· 22

• Cucire un nastro ························································· 22

Details of the machine / Detalles de la máquina

Détails de la machine / Dettagli della macchina

Details of the machine

1. Looper cover with built in knife guard

2. Looper cover opening indent

3. Cloth plate

4. Sewing light

5. Thread take-up cover

6. Presser foot pressure regulating knob

7. Left needle thread tension dial

8. Right needle thread tension dial

9. Upper looper thread tension dial

10. Lower looper thread tension dial

11. Retractable support rod

12. Thread guide support

13. Open thread guide

14. Spool holder pin

15. Foam pad

16. Anti - vibration cone

17. Thread stand

18. Stitch length adjustment dial

19. Differential feed adjustment dial

20. Handwheel

21. Side cover

22. Matching up marks

23. Machine socket

24. Main Power/Light switch

25. Light switch

26. Positioning lever (L or R)

Detalles de la máquina

1. Tapa de la lanzadera con protección de

la cuchilla integrada

2. Guía para abrir la tapa de la lanzadera

3. Tapa de la mesa de trabajo

4. Luz de trabajo

5. Protección tensor del hilo

6. Botón regulador de la presión del pie

prensatelas

7. Tensión del hilo de la aguja izquierda

8. Tensión del hilo de la aguja derecha

9. Tensión del hilo de la lanzadera superior

10. Tensión del hilo de la lanzadera inferior

11. Soporte telescópico del guía-hilo

12. Guía-hilo

13. Guía-hilo abierto

14. Espigas para las bobinas de hilo

15. Base de material esponjoso

16. Antivibradores

17. Porta-bobinas

18. Botón regulador del largo del punto

19. Botón regulador del transporte

diferencial

20. Volante

21. Tapa lateral

22. Marcas en el volante y tapa lateral

23. Enchufe para la red eléctrica

24. Interruptor principal y de la luz

25. Interruptor de la luz

26. Posicionamiento de palanca

(L (izquierda) o R (derecha))

Details of the machine

1. Thread cutter

2. Automatic needle threader

3. Presser foot lifter

4. Stitch plate

5. Presser foot

6. Upper knife

7. Needle clamp

Détails de la machine

1. Couvercle des boucleurs avec

recouvrement du couteau intégré

2. Guide pour ouvrir le couvercle des

boucleurs

3. Plateau de travail

4. Eclairage / ampoule

5. Couvercle du tendeur de fil

6. Bouton de réglage de la pression du pied

7. Tension du fil d’aiguille de gauche

8. Tension du fil d’aiguille de droite

9. Tension supérieure du fil de boucleur

10. Tension inférieure du fil de boucleur

11. Support de guide-fil télescopique

12. Garniture de guidage

13. Guide-fil ouvert

14. Broche

15. Socle en mousse

16. Antivibreurs

17. Support de broches à bobines

18. Sélecteur pour longueur de point

19. Sélecteur pour entraînement différentiel

20. Volant

21. Capot latéral

22. Repères sur le volant et le capot latéral

23. Prise de la machine

24. Commutateur principal et interrupteur

de lumière

25. Interrupteur de lumière

26. Levier de positionnement (L (gauche)

ou R (droite))

Deattagli della macchina

1. Coperchio del crochet con copertura

del coltello integrata

2. Sede per aprire il coperchio del crochet

3. Coperchio appoggia stoffa

4. Illuminazione

5. Copertura leva tendi filo

6. Regolazione pressione del piedino

7. Tensione del filo ago sinistro

8. Tensione del filo ago destro

9. Tensione del filo crochet superiore

10. Tensione del filo crochet inferiore

11. Asta guidafilo telescopica

12. Supporto guidafilo

13. Guide aperte

14. Perni portaspolette

15. Protezione in gomma

16. Coni antivibrazioni

17. Porta spolette

18. Regolazione lunghezza del punto

19. Regolazione trasporto differenziale

20. Volantino

21. Coperchio laterale

22. Marcatura sul volantino e coperchio

laterale

23. Presa corrente

24. Interruttore principale

25. Interruttore illuminazione

26. Leva posizione (sinistra o destra)

Detalles de la máquina

1. Corta-hilos

2. Enhebrador automático

3. Palanca alza-prensatelas

4. Placa-aguja

5. Prensatelas

6. Cuchilla superior

7. Sujeta-agujas

Dettagli della macchina

1. Taglia filo

2. Infila ago automatico

3. Leva alza piedino

4. Placca ago

5. Piedino

6. Coltello superiore

7. Morsetto degli aghi

Détails de la machine

1. Coupe-fil

2. L’enfileur automatique

3. Levier du pied-de-biche

4. Plaque à aiguille

5. Pied-de-biche

6. Couteau supérieur

7. Porte-aiguille

Accessories

1. Needle set 130/705H (SCHMETZ)

2. Small screwdriver

3. Tweezers

4. Upper looper converter

5. Brush/needle inserter

6. Electronic foot control

7. Oiler

8. Nets

9. Lower knife

10. Spool caps

11. Accessory bag

12. Dust cover

13. Large screwdriver

14. Bulb holder

15. Waste collector

View with looper cover open

1. Selection lever for overlocking or roll

hemming

2. Lower knife

3. Cutting width adjusting dial

4. Lower looper auto threader

5. Lower knife setscrew

6. Lower looper

7. Upper looper

8. Threading diagram

9. Slit type looper threading system

Vista con la tapa de la lanzadera

abierta

1. Palanca selectora para overlock o

dobladillo enrollado

2. Cuchilla inferior

3. Botón regulador para la posición de la

cuchilla

4. Enhebrador automático de la lanzadera

inferior

5. Tornillo de fijación de la cuchilla inferior

6. Lanzadera inferior

7. Lanzadera superior

8. Esquema de enhebrado

9. Guías abiertas

Vista con il coperchio del crochet

aperto

1. Levetta selezione overlock o orlino

arrotolato

2. Coltello inferiore

3. Manopola regolazione del coltello

4. Infilatore automatico del crochet inferiore

5. Vite di arresto del coltello inferiore

6. Crochet inferiore

7. Crochet superiore

8. Schema di infilatura

9. Guida passafilo crochet

Accesorios

1. Juego de agujas 130/705H (SCHMETZ)

2. Destornillador pequeño

3. Pinzas

4. Transformador lanzadera ciega

superior

5. Pincel / coloca-agujas

6. Pedal de mando electrónico

7. Aceitera

8. Redes

9. Cuchilla inferior

10. Arandelas guía-hilo

11. Bolsa para los accesorios

12. Funda contra el polvo

13. Destornillador grande

14. Soporte para la bombilla

15. Recipiente para retales

Accessori

1. Aghi 130/705H (SCHMETZ)

2. Cacciavite piccolo

3. Pinzetta

4. Copertura del crochet superiore

5. Pennello / aiuta cambia-ago

6. Reostato

7. Olio

8. Reti salvafilo

9.Coltello inferiore

10. Dischi svolgi filo

11. Borsetta accessori

12. Fodera antipolvere

13. Cacciavite grande

14. Lampadina

15. Contenitore per ritagli di stoffa

Details of the machine / Detalles de la máquina

Détails de la machine / Dettagli della macchina

Vue, le couvercle du boucleur

ouvert

1. Levier sélecteur pour point de surjet ou

ourlets roulés

2. Couteau inférieur

3. Sélecteur pour la position du couteau

4. Enfilage automatique du boucleur

inférieur

5. Vis de réglage pour le couteau inférieur

6. Crochet inférieur

7. Crochet supérieur

8. Répertoire d’enfilage

9. Guide

Accessoires

1. Jeu d’aiguilles 130/705H (SCHMETZ)

2. Petit tournevis

3. Pincette

4. Recouvrement du boucleur supérieur

5. Pinceau / pose-aiguille

6. Pédale électronique

7. Huileur

8. Réseaux

9. Couteau inférieur

10. Rondelles de maintien

11. Pochette d’accessoires

12. Housse de protection

13. Grand tournevis

14. Outil spécial pour ampoule

15. Récupérateur de chutes

Polarized plug

(for USA, Canada only)

Polarized main socket

Attaching the foot control

Plug foot control into the machine socket (A) and then into main socket (B). The foot

control regulates the sewing speed. The sewing speed can be adjusted by increasing

or decreasing the pressure on the foot control.

“WARNING’’

This appliance has a polarized plug (one blade wider than the other).

To reduce the risk of electric shock, this plug is intended to fit in a polarized main socket

only one way.

If the plug does not fit fully in the polarized main socket, reverse the plug. If it still does not

fit, contact a qualified electrician to install the proper polarized main socket. Do not modify

the plug in any way.(for USA, Canada only)

* For MO-734DE use only the foot control model YC-482(USA,CANADA),

YC-483N(220-240V)

Conexión del pedal de mando

Enchufar el pedal de mando en el enchufe de la máquina overlock (A) y seguidamente

enchufar el enchufe en la red eléctrica (B). Apretando más o menos el pedal de mando

se regula a progresión continua la velocidad de la costura.

Raccordement de la pédale

Introduire la fiche de la pédale dans la prise de la surjeteuse (A), puis relier la prise

secteur (B) au réseau. Une pression plus ou moins grande sur la surface d’appui de la

pédale permet de modifier progressivement la vitesse de la machine.

Collegamento del reostato

Inserire la spina del reostato nella presa della macchina (A). Poi collegare la spina di rete

con la presa di rete(B). Premendo più o meno sulla pedana del reostato si può regolare

la velocità di cucito, progressivamente.

Preparing the machine / Using the machine

Preparación de la máquina / puesta en servicio

Préparation de la machine / mise en service

Preparazione della macchina / messa in servizio

Waste collector

Clip the waste collector into the opening on the looper cover. It catches the cut-off fabric

as you sew, keeping your working area neat and tidy.

Recipiente para retales

Enganchar el recipiente para retales en la muesca de la tapa de la lanzadera. El recipiente

recoge todos los retales cortados durante la costura. El campo de trabajo queda limpio

y ordenado.

Récupérateur de chutes

Suspendre le récupérateur de chutes dans l’évidement du couvercle du boucleur. Le

récipient récupère les déchets après la coupe du tissu. Le poste de travail reste propre

et bien ordonné.

Contenitore per ritagli di stoffa

Agganciare il contenitore nell’apertura del coperchio del crochet. Il recipiente raccoglie i

resti di stoffa subito dopo il taglio. Il posto di lavoro resta pulito e ordinato.

Thread stand

Push the support rod firmly into the socket on the back of the machine.

Raise the support rod (C) fully, turning slightly until the position catches engage. Position

the thread guide (D) on the thread stand so that the arrow is to the front.

Guía-hilo

Estirar completamente el soporte telescópico del guía-hilo y girarlo hasta que se enganche

en la posición correspondiente (C). Inserir el guía-hilo (D) de manera que la flecha

indique hacia adelante.

Guide-fil

Sortir le support de guide-fil jusqu’à la butée, le tourner jusqu’à ce qu’il s’encliquette (C)

dans les positions correspondantes. Introduire le guide-fil (D) sur le support de guide-fil

de sorte que la flèche soit orientée vers l’avant.

Asta guidafilo

Estrarre l’asta telescopica completamente, girarla leggermente finchè si innesta nelle

rispettive posizioni (C) Montare il supporto guidafili (D) con la freccia in avanti.

Preparing the machine / Using the machine

Preparación de la máquina / puesta en servicio

Préparation de la machine / mise en service

Preparazione della macchina / messa in servizio

Thread / cones / spools

The anti-vibration cone should be used with the wider edge at the bottom on the spool holder

pin when sewing with cones.

Colocación de bobinas

Para conos normales colocar los antivibradores en las espigas con la parte ancha hacia

abajo.

Mise en place des bobines de fil

Lors de l’emploi de cônes de fil normaux, placer les antivibreurs sur les broches en tournant

le côté le plus large vers le bas.

Spolette normali

Per spolette coniche normali usare gli antivibratori con la parte larga rivolta verso il basso.

Thread net

If the threads slip and get twisted, cover the looper spools with the net supplied in the

accessory bag.

Redes

Para hilos finos, que se deshilan fácilmente del cono, cubrir las bobinas con las redes que se

encuentran en la bolsa de accesorios.

Résille pour fil

Pour les fils fins qui tombent facilement du cône, recouvrir les bobines avec la résille rangée

dans la pochette d’accessoires.

Rete salvafilo

Usando fili molto sottili, che cadono facilmente dal cono, proteggere le spolette con le reti che

si trovano nella borsa accessori.

Household spools

Remove the anti-vibration cones. Place spools on spool holder pins and push the spool caps

on with the rounded side downwards.

Bobinas corrientes

Para las bobinas corrientes quitar los antivibradores.

Colocar las bobinas. Seguidamente poner las arandelas guía-hilo en las espigas, el borde

redondeado mirando hacia abajo.

Bobines familiales

Pour les bobines familiales, enlever les antivibreurs, placer les bobines de fil. Ensuite, introduire

les rondelles de maintien sur les broches avec l’arrondi du bord extérieur tourné vers le bas.

Spolette per uso domestico

Usando spolette per uso domestico, togliere i coni antivibrazioni. Infilare le spolette direttamente

sui perni, fissarle poi con i dischi svolgi-filo, messi con i bordi arrotondati rivolti in giù.

Large spools

If large industrial spools are used, position the anti-vibration cone upside down on the spool

holder pin, i .e. with the wider edge at the top.

Bobinas grandes

Para bobinas industriales grandes, poner los antivibradores al revés, es decir con la parte

ancha hacia arriba.

Grandes bobines

Si vous vous servez de grandes bobines industrielles, installez les antivibreurs à l’envers,

c’est-à-dire sur les broches en tournant le côté le plus large vers le haut.

Spole grosse industriali

Per le spole grandi industriali usare gli antivibratori nel senso inverso, cioè con la loro parte

larga verso l’alto.

Preparing the machine / Using the machine

Preparación de la máquina / puesta en servicio

Préparation de la machine / mise en service

Preparazione della macchina / messa in servizio

Main Power/light switch

The main power/light switch is conveniently placed

on the handwheel side of the machine in front of the

socket.

0 = Off

I = On with light

Commutateur principal et interrupteur

de lumière

Le commutateur principal / interrupteur de lumière

est disposé visiblement du côte du volant devant la

prise de la machine.

0 = arrêt

I = marche

Raising the upper knife

Switch the machine off (power switch”O")

• Turn the handwheel towards you until the needles

are fully raised.

• Open the looper cover.

Press the upper knife holder (E) to the right. Turn the

knob clockwise (F) until the knife is in the position

illustrated (G).

Subir / bajar la cuchilla superior

Desconectar la máquina, interruptor

principal a „O“.

• Girar el volante hacia adelante hasta que las agujas

estén en su posición más alta.

• Abrir la tapa de la lanzadera.

Apretar el soporte de la cuchilla superior (E) hacia

la derecha y girar el botón (F) en el sentido de las

agujas del reloj hasta que la cuchilla se encaje como

en la ilustración (G).

Relever et abaisser le couteau

supérieur

Couper le circuit de la machine en mettant le

commutateur principal sur „O“.

• Tourner le volant en avant et amener les aiguilles

à leur position la plus élevée.

• Ouvrir le couvercle du boucleur.

Presser le support supérieur du couteau (E) tout à

fait à droite, puis tourner le bouton rotatif dans le

sens des aiguilles d’une montre (F) jusqu’à ce que

le couteau s’encliquette, comme le montre l’illustration

(G).

Alzare il coltello superiore

Spegnere la macchina mettendo

l’interruttore principale su „O“ disinserito.

• Portare gli aghi alla loro massima altezza, girando

il volantino in avanti. La freccia del volantino e quella

del coperchio laterale combaciano.

Aprire il coperchio del crochet. Spingere il porta

coltello superiore (E) verso destra e girare il bottone

nel senso orario (F) come illustrato, finchè il coltello

s’innesta (G).

Using the machine / Puesta en servicio

Mise en service / Uso della macchina

Light switch

The light switch is placed on the rear left side of the

machine, above the presser foot lifter.

E = on

F = off

Interrupteur de lumière

L’interrupteur de lumière est situé à l’arrière de la

machine, au-dessus du levier du pied-de-biche.

E = marche

F = arrêt

Interruptor de la luz

El interruptor se encuentra en la parte posterior de

la máquina, encima de la palanca alza-prensatelas.

E = luz encendida

F = luz apagada

Interruttore illuminazione

L’interruttore di illuminazione si trova sull’estremo

lato sinistro della macchina, sopra la leva alzapiedino.

E = inserito

F = disinserito

Interruptor principal y de la luz

El interruptor principal y de la luz se encuentra bien

visible en la parte del volante, delante del enchufe

de la máquina.

0 = off (desconectada)

I = on (conectada)

Interruttore principale e illuminazione

L’interruttore principale si trova sulla parte destra

della macchina sotto il volantino

0 = disinserito

I = inserito

Two step presser foot lifter with

integrated front foot lift

To raise the presser foot, lift the presser foot

lever on the rear of the machine, until it engages

(A). It can be raised again to the maximum height

and held in this position to provide more space

between presser foot and stitch plate (B).

When the foot is raised (A and B), the front of

the foot is automatically lifted.

Note: When the presser foot is raised, all the

tensions are released making it easier to thread

the machine.

Palanca alza-prensatelas con dos

escalas y alza-punta-prensatelas

integrado.

Para levantar el prensatelas subir la palanca alza-

prensatelas hacia arriba hasta que se encaje

(A). Si se empuja la palanca alza-prensatelas

hasta arriba del todo entonces aumenta la

separación entre la placa-aguja y el prensatelas

(B). Cuando el prensatelas está arriba (A+B)

entonces también está levantada la punta del

prensatelas.

Indicación: Cuando el prensatelas está elevado,

todas las tensiones de los hilos están aflojadas

para facilitar el enhebrado.

Changing the presser foot

• Switch the machine off (power

switch”0")

• Raise the presser foot.

• Turn handwheel towards you until needles

are fully raised. Match the matching up marks on

handwheel and side cover.

Press the catch (C) to release the presser foot

from the clamp. Raise the presser foot shank to

the highest position (B) and remove the presser

foot to the left. To attach the presser foot, place

it under the shaft. The groove in the shaft should

line up exactly with the presser foot pin (D).

Lower the shank and the presser foot will en-

gage automatically.

Cambio del prensatelas

• Desconectar la máquina, interruptor

principal a „O“.

• Subir el prensatelas.

• Girar el volante hacia adelante y colocar las

agujas en su posición más alta. Marcas en el

volante y tapa lateral están lado a lado.

Apretar la palanca (C). El prensatelas se

desengancha de su sujeción. Apretar la palanca

alza-prensatelas hasta arriba del todo (B) y sacar

el prensatelas por la parte izquierda.

Para enganchar el prensatelas, situarlo debajo

del vástago. La ranura del vástago tiene que

estar exactamente sobre el perno del pie (D).

Bajar el vástago, el pie se engancha.

Levier du pied-de-biche à deux

positions avec releveur intégré des

pointes du pied-de-biche.

Pour relever le pied-de-biche, déplacer le levier

du pied-de-biche vers le haut, jusqu’à ce qu’il

bute (A). Si le levier est pressé tout à fait en

haut, l’écart entre la plaque à aiguille et le pied-

de-biche (B) est agrandi. Si le pied-de-biche est

en haut (A+B), la pointe du pied-de-biche est

aussi relevée.

Indication: si le pied-de-biche est relevé, toutes

les tensions de fil sont libérées. De cette manière,

l’enfilage devient plus facile.

Leva alzapiedino a due posizioni

con alza punta integrato.

Per alzare il piedino spingere la leva alza piedino

in alto fino al suo arresto (A). Spingendo la leva

ancora più in alto si ottiene la massima distanza

possibile tra piedino e placca d’ago (B) Se il

piedino si trova in alto (A+B), è alzata anche la

punta del piedino.

Indicazione: Con il piedino alzato tutte le tensioni

del filo sono aperte per facilitare l’infilatura.

Remplacement du pied-de-biche

• Couper le circuit de la machine en

mettant le commutateur principal sur „O“.

• Relever le pied-de-biche.

• Tourner le volant en avant et amener les aigu-

illes à leur position la plus élevée. Placer, côte à

côte, les flèches de repère du volant et du capot

latéral.

Presser le levier de libération (C). Le pied-de-

biche se libère de son support. Presser le levier

du pied-de-biche tout à fait en haut (B), puis

retirer le pied-de-biche par la gauche.

Pour fixer le pied-de-biche, le poser sous la tige.

Pour cela, la rainure de la tige doit être exactement

au-dessus de la tige du pied-de-biche (D).

Abaisser la tige, le pied-de-biche s’encliquette.

Sostituzione del piedino

• Spegnere la macchina, l’interruttore

principale su „O“ disinserito.

• Alzare il piedino.

• Girare il volantino in avanti per portare gli aghi

nella loro posizione più alta. La freccia del volantino

e quella del coperchio laterale devono

combaciare.

Premere la leva di disinnesto (C). Il piedino si

stacca dal gambo. Alzare del tutto la leva

alzapiedino (B) e togliere poi il piedino tirandolo

verso sinistra. Per montare il piedino posizionarlo

sotto il gambo.L’incavo nel gambo deve trovarsi

esattamente sopra il perno nel piedino (D).

Abbassare il gambo, il piedino si innesta

automaticamente.

Using the machine / Puesta en servicio

Mise en service / Uso della macchina

Looper cover

To open, press to the right with your thumb in the indent provided and tilt the cover towards

you. To close push it up and press lightly to the right.

The cover engages automatically.

Safety switch: The machine does not run when the looper cover is opened.

Tapa de la lanzadera

Para abrir la tapa de la lanzadera hay que empujarla con el pulgar hacia la derecha y abrirla

hacia sí mismo. Para cerrarla, levantarla y empujarla ligeramente hacia la derecha hasta

que se encaje.

Interruptor de seguridad: La máquina no cose cuando la tapa de la lanzadera está abierta.

Couvercle du boucleur

Pour ouvrir le couvercle du boucleur, pousser à droite, sur l’échancrure, avec le pouce,

puis faire basculer le couvercle vers l’avant. Pour refermer, relever le couvercle, puis le

presser légèrement à droite jusqu’à ce qu’il s’encliquette.

Commutateur de sécurité: la machine ne coud pas si le couvercle du boucleur est ouvert.

Coperchio del crochet

Spingere il coperchio con il pollice nell’incavo verso destra e farlo ribaltare in avanti.

Per chiuderlo alzare il coperchio e premerlo poi leggermente verso destra. Il coperchio si

innesta automaticamente.

Cloth plate

Opening and closing the cloth plate:

Opening: Push the cloth plate to the left.

Closing: Push the cloth plate to the right.

Safety switch: The machine does not run when the cloth plate is opened.

Tapa de la mesa de trabajo

Abrir y cerrar la tapa de la mesa de trabajo:

Abrir: Deslizar la tapa hacia la izquierda.

Cerrar: Deslizar la tapa hacia la derecha.

Interruptor de seguridad: La máquina no cose cuando la tapa de la mesa de trabajo está

abierta.

Plateau de travail

Ouverture et fermeture du plateau de travail:

Ouverture: déplacer le plateau de travail à gauche.

Fermeture: déplacer le plateau de travail à droite.

Commutateur de sécurité: la machine ne coud pas si le couvercle du plateau de travail est

ouvert.

Coperchio appoggia-stoffa

Apertura e chiusura del coperchio appoggia stoffa

Aprire:Premere il coperchio appoggia-stoffa verso sinistra.

Chiudere: Premere il coperchio appoggia-stoffa verso destra.

Dispositivo di sicurezza: La macchina non cuce se il coperchio appoggia-stoffa è aperto.

Handwheel

The handwheel turns forward, i.e. in the same direction as on a household sewing

machine.

Volante

El volante se gira en sentido contrario de las agujas del reloj, igual como en una máquina

de coser.

Volant

Le volant tourne dans le sens inverse des aiguilles d’une montre, comme sur la machine à

coudre familiale.

Volantino

Il volantino gira in senso antiorario, come il volantino per le macchine per cucire.

Using the machine / Puesta en servicio

Mise en service / Uso della macchina

Inserting the needles

Needles can be inserted quickly and easily with the practical needle inserter (A).

Switch the machine off (Power switch to “0”)

Disconnect machine from electricity supply.

Turn handwheel towards you until needles are fully raised. Match the matching up

marks on handwheel and side cover.

Lower the presser foot.

Using the small screwdriver, loosen the needle setscrews and remove the needles (B).

Place the right-hand needle, flat side towards the back, into the hole of the needle

inserter and insert the needle as far as possible into the needle clamp. Tighten the

setscrew lightly and then insert the left-hand needle in the same way and tighten both

setscrews (C).

Colocar agujas

Con el coloca-agujas en el mango del pincel se pueden colocar las agujas fácil y

rápidamente (A).

Desconectar la máquina, interruptor principal a „O“.

Girar el volante hacia adelante hasta que las agujas estén en su posición más alta.

Marcas en el volante y tapa lateral están lado a lado.

Bajar el prensatelas.

Aflojar los tornillos de sujeción con el destornillador pequeño. Sacar las agujas (B).

Según el punto escogido, colocar la aguja derecha o izquierda.

Colocar la aguja, con la parte plana mirando hacia atrás, en el agujero del pincel e

introducir las agujas en el sujeta-agujas, hasta llegar al tope.

Apretar los tornillos de sujeción (C).

Mettre les aiguilles en place

Le guide d’aiguille situé dans le manchon du pinceau permet la mise en place facile et

rapide des aiguilles (A).

Couper le circuit de la machine en mettant le commutateur principal sur „O“.

Tourner le volant en avant et amener les aiguilles à leur position la plus élevée. Placer,

côte à côte, les flèches de repère du volant et du capot latéral.

Abaisser le pied-de-biche.

Desserrer la vis de fixation de l’aiguille avec le petit tournevis. Enlever les aiguilles (B).

Selon le point choisi, introduire l’aiguille à droite ou à gauche.

Placer les aiguilles avec le côté plat à l’arrière dans le guide situé sur le manchon du

pinceau, puis introduire les aiguilles dans le porte-aiguille jusqu’à ce qu’elles butent en

haut. Resserrer les vis de fixation des aiguilles (C).

Sostituzione degli aghi

Il piccolo foro del pennello regge l’ago e facilita la sostituzione (A):

Spegnere la macchina, l’interruttore principale su “O”

Portare gli aghi alla loro massima altezza girando il volantino in avanti. La freccia del

volantino e quella del coperchio laterale combaciano.

Abbassare il piedino.

Svitare le viti degli aghi con il cacciavite piccolo. Togliere gli aghi (B). Inserire l’ago destro

o sinistro, secondo la selezione del punto.

Inserire l’ago nuovo nel foro del pennellino.

Poi introdurre l’ago con la parte piatta rivolta indietro nel morsetto degli aghi, spingendolo

bene in alto fino al suo arresto.

Stringere le viti di fissaggio (C).

Using the machine

Puesta en servicio / enhebrado

Mise en service / enfilage

Uso della macchina / infilatura

Needle and thread / Aguja e hilo

Aiguille et fil / Ago e filo

Needles

Needles must be in perfect condition. Problems can occur if needles:

A are bent.

B are damaged or blunt.

C have hooked points.

Agujas

Las agujas deben estar impecables. Aparecen dificultades en los siguientes casos:

A Aguja torcida

B Aguja despuntada, estropeada

C punta de aguja con barbas

Aiguille

Les aiguilles doivent être en bon état. Des difficultés apparaîtront dans les cas suivants:

A Aiguille tordue.

B Aiguille émoussée ou endommagée.

C Pointe de l’aiguille avec des bardes.

Ago

L’ago deve essere sempre perfetto. I problemi sono causati da:

A Ago storto

B Ago spuntato, danneggiato

C Punta danneggiata

Needle and thread

The needle size used depends on the thread. The needles should be in accordance with

thread used.

When sewing, the thread is fed through the long groove in the needle. If the needle is too

fine, the thread does not fit into the groove and stitches will be skipped.

Use needles No. 70 - 90.

* It is recommended to use JLx2 needle, especially when sewing thick materials, over-

lapped section, etc, with overlock machine.

Aguja e hilo

El grosor se la aguja depende del hilo escogido, es decir la aguja tiene que ser adecuada

para el hilo.

Durante la costura, el hilo entra en la ranura delantera de la aguja. Si la aguja es

demasiado fina el hilo no cabe en la ranura y salen puntos defectuosos.

Utilizar agujas No. 70 – 90.

* Se recomienda usar aguja JLx2, especialmente para coser materiales pesados,

secciones superpuestas, etc. con máquina sobreorilladora.

Aiguille et fil

La grosseur de l’aiguille dépend du fil choisi. L’aiguille doit concorder avec le fil.

Lorsque l’on pique, le fil se place dans la longue rainure de l’aiguille. Si cette dernière est

trop fine, le fil ne peut entrer dans la rainure, ce qui empêche les points de se former

correctement.

Employer des aiguilles no. 70-90.

* Il est recommandé d’utiliser l’aiguille JLx2, tout particulièrement lors de la couture de

tissus épais, de parties se chevauchant, etc., avec une surjeteuse.

Ago e filo

Lo spessore dell’ago dipende sempre dalla scelta del filo e l’ago deve essere adatto al

filo. Il filo passa durante il cucito nella lunga scanalatura sul davanti dell’ago. Se l’ago è

troppo sottile, il filo non trova abbastanza spazio nella scanalatura ed il risultato sono

punti saltati o difettosi.

Usare sempre aghi n°70-90.

* E’ raccomandato l’uso dell’ago JLx2, specialmente per cucire materiale pesante tessuti

sovrapposti, ecc, per macchine tagliacuci.

Needle and thread / Aguja e hilo

Aiguille et fil / Ago e filo

Thread/decorative threads

Sewing and special overlock threads are manufactured in a wide variety

of types, weights and combination of fibres. It is worth investing in good

quality threads for perfect sewing results. Decorative threads specially

made for overlockers (available on cones) are also becoming widely avail-

able. We recommend following the basic guidelines when using special

threads on your overlocker:

- Purchase threads on cones or spools which are produced exclusively

for overlocking.

- When using normal spools, use the spool caps (in accessory bag).

- Only use decorative threads in the loopers. The thread must move easily

and without resistance through the thread guides and looper eyes.

- The thicker the thread, the longer the stitch length (3-4).

- The thicker the thread, the looser the tensions

- Sew slowly when using decorative threads. Pull the thread chain gently

to the rear when starting to sew.

Always test sew decorative threads before starting to sew your work.

Hilo, hilo decorativo

Hay una multitud de hilos para coser y para overlock en diversas calidades.

Para obtener un resultado perfecto vale la pena utilizar hilos de alta calidad.

Además de los hilos normales, hoy día también se encuentran hilos

decorativos para overlock (en conos).

Observar las siguientes reglas básicas para el uso de hilos especiales:

- Escoger hilos que estén en bobinas o conos para overlock.

- Si se utilizan bobinas normales, poner las arandelas guía-hilo (se encuentran

en la bolsa de accesorios).

- Utilizar los hilos decorativos únicamente en las lanzaderas. El tamaño del

ojete indica el grosor máximo del hilo decorativo. Los hilos decorativos

tienen que enhebrarse sin sentir ninguna resistencia.

- Más grueso es el hilo, más largo es el punto (largo del punto 3-4).

- Más grueso es el hilo, más baja es la tensión del hilo.

- Coser despacio cuando se utiliza hilo decorativo. Al inicio de la costura

tirar ligeramente la cadena de hilo hacia atrás.

Antes de empezar a coser con hilos decorativos, hacer una costura de

prueba.

Fils, fils décoratifs

Les fils à coudre et les fils pour surjeteuse sont disponibles dans de nombreuses

qualités et épaisseurs. Préférez toujours des fils à coudre de très bonne qualité

pour obtenir du travail parfait. En plus des fils à coudre courants, on trouve

également des fils décoratifs pour surjeteuse (sur cônes). Prière d’observer

les règles de base suivantes lors de l’emploi de fils spéciaux: choisir des fils

dont la présentation sur bobines ou cônes correspond aux surjeteuses.

Poser les disques de déviation du fil qui se trouvent dans la pochette d’accessoires

lorsqu’on emploie des bobines normales.

Les fils décoratifs seront utilisés uniquement dans les boucleurs. L’importance

du chas des boucleurs détermine l’épaisseur maximale du fil. L’enfilage des fils

décoratifs doit s’effectuer sans se heurter à une résistance.

Plus le fil est épais, plus la longueur de point doit être élevée (longueur de point

3-4mm)

Plus le fil est épais, plus la tension de fil doit être faible!

L’emploi de fils décoratifs demande de réduire la vitesse de couture. Toujours

tirer la chaînette de fil en arrière avant de commencer la couture.

Effectuer toujours un essai avant de travailler avec les fils décoratifs.

Filo, filo decorativo

Filati per cucire e per overlock sono disponibili in tante qualita’ e spessori

Per ottenere un risultato perfetto si consiglia di adoperare sempre filati di

qualità. Oggi esistono anche per la tagliacuce (su cono) una vasta scelta di

fili decorativi. Osservare le seguenti regole per l’uso di questi filati:

-Scegliere confezioni adatte per tagliacuce (per es. su cono).

-Adoperare sempre i dischi svolgi-filo con le spolette normali.

-Usare fili decorativi solo nei crochet; lo spessore massimo dipende dalla

cruna del crochet; il filo deve passare senza difficoltà attraverso la cruna.

-Più pesante è il filo,più lungo deve essere il punto (lunghezza 3-4)

-Più pesante è il filo, più bassa deve essere la tensione del filo.

-Cucire lentamente con il filo decorativo; all’inizio della cucitura tirare la

catenella leggermente indietro.

Fare sempre una prova di cucitura con filati decorativi.

Thread, needle, application table

Tabla de hilos, agujas, tejidos Tabella di Filo, Ago, Applicazione

Thread

All purpose overlock

thread 120/2 (polyester)

Spun Polyester

Needles Where Application

Needles and

looper threads

70-90 For all overlock.

Loopers onlyPolyester-continuous

filaments

Neatening edges

Woolly nylon Loopers only Soft seams in knits,

rolled hems.

80-90 Needles, and

looper threads

70-90

Embroidery/darning and

decorative threads

Neatening edges,

rolled hems.

Seams in all fabrics.

Loopers only

Hilo

Cosetodo overlock

(poliéster)

Hilo de coser

poliéster

Aguja Enhebrado Aplicación

Hilo de aguja y

lanzadera

70-90 Para todos los

trabajos overlock

Sólo adecuado como

hilo de la lanzadera

Hilo de poliéster

(sinfín)

Sobrehilado de los

bordes cortados

Hilo de fibra Sólo adecuado

como hilo de la

lanzadera

Costuras finas en

tejidos de punto,

dobladillo enrollado

80-90 Hilo de aguja y

lanzadera

70-90Hilo de bordar y

de zurcir

Sobrehilado de los

bordes cortados,

dobladillo enrollado.

Costuras en toda

clase de tejidos

Sólo adecuado

como hilo de la

lanzadera

Tableau des aiguilles, fils et tissus

Fil

Fil surjet universel

(polyester)

Fil à coudre en

polyester

Aiguille Destination Application

Fil d’aiguille et fil

de boucleur

70-90

Convient pour tous les travaux

avec le point de surjet et le

pointenveloppant

Convient seulement

comme fil de boucleur

Fil invisible en

polyester

Surfilage des bords

Fil texturé

Convient seulement

comme fil de boucleur

Coutures souples dans des

tissus à mailles, ourlets roulés

80-90 Fil d’aiguille et fil

de boucleur

70-90Fil à broder, fil à

repriser et fil

décoratif

Surfilage des bords,

ourlets roulés

Couture sur tous tissus

Fil d’aiguille et fil

de boucleur

Filo

Filo overlock stan-

dard (Poliestere)

Filo per cucire

pol.

Ago Utilizzo Applicazione

Filo dell'ago

Filo del crochet

70-90 Per qualsiasi

lavorazione

Solo come filo del

crochet

Filo invisibile

poliestere

Rifinitura dei margini

Filanca Solo come filo del

crochet

Cuciture morbide per

maglieria. Orli arrotolati

80-90 Filo dell'ago

Filo del crochet

70-90Filo per ricamo

rammendo/

decorativo

Rifinitura margini

Orli arrotolati e punto di

copertura

Cuciture su tutti i materiali

Solo come filo del

crochet

Adjustments and settings / Regulación y manejo

Réglage et utilisation / Regolazione ed uso

Stitch length

It can be adjusted while sewing.

The stitch length is infinitely variable from

1-4mm. Most overlock work is done with a

basic setting of 2.5mm.

Largo del punto

El largo del punto puede regularse durante

la costura, y a progresión continua, entre

1 mm y 4 mm.

La mayoría de los trabajos overlock se

cosen con un largo del punto de 2.5 mm.

Longueur de point

La longueur de point peut être réglée

progressivement, même pendant la cou-

ture. La longueur de point est réglable

progressivement dans la zone comprise

entre 1 et 4 mm. La plupart des travaux

avec la surjeteuse sont cousus avec une

longueur de point fixée à 2,5 mm.

Lunghezza del punto

La lunghezza del punto può essere

regolata in cucitura. E’ regolabile

progressivamente tra 1-4 mm. anche du-

rante la cucitura. La maggior parte di

lavorazione overlock sono cucite con una

lunghezza di 2.5 mm.

Cutting width

Switch the machine off (Power

switch to “0”)

Disconnect machine from electricity

supply.

• Raise the upper knife.

• Turn cutting width adjustment dial in

the desired direction.

• Lower upper knife.

1 = 4–6 mm seam width

2 = 5–7 mm seam width

3 = 6–8 mm seam width

4 = 7–9 mm seam width

5 = 8–10 mm seam width

The position of the lower knife determines

the width of the seam.

Reduce the cutting width if the edges of

fine fabric curl up when being sewn (A).

Increase the cutting width if the loops seem

to be too loose (B).

Posición de la cuchilla

Desconectar la máquina, interruptor

principal a „O“.

• Subir la cuchilla.

• Girar el botón regulador de la posición

de la cuchilla en la dirección deseada.

• Bajar la cuchilla.

Posición de la cuchilla

1 = ancho de la costura de 4–6 mm

2 = ancho de la costura de 5–7 mm

3 = ancho de la costura de 6–8 mm

4 = ancho de la costura de 7–9 mm

5 = ancho de la costura de 8–10 mm

Si el tejido se enrolla durante la costura,

reducir el ancho de la costura girando el

botón regulador de la posición de la cuchilla

hacia 1 (A).

Si el enlace de los hilos parece demasiado

flojo, aumentar el ancho de la costura

girando el botón regulador de la posición

de la cuchilla hacia 5 (B).

Position du couteau

Couper le circuit de la machine en

mettant le commutateur principal sur

„O“.

• Relever le couteau.

• Tourner le sélecteur de position du

couteau dans la direction souhaitée.

• Abaisser le couteau.

Position du couteau

1 = largeur de couture 4-6 mm

2 = largeur de couture 5-7 mm

3 = largeur de couture 6-8 mm

4= largeur de couture 7-9 mm

5= largeur de couture 8-10 mm

Réduire la largeur de couture, si le tissu

s’enroule pendant la couture. Tourner alors

le sélecteur de position du couteau vers 1

(A).

Augmenter la largeur de couture, si le

nouage apparaît lâche. Tourner alors le

sélecteur de position du couteau vers 5

(B).

Larghezza del taglio

Spegnere la macchina, l’interruttore

principale su “0”. Scollegare la

macchina

• Alzare il coltello superiore.

• Girare la manopola per la regolazione del

coltello nella direzione desiderata.

• Abbassare il coltello superiore.

Posizione del coltello

1 = Larghezza cucitura tra 4-6 mm

2 = Larghezza cucitura tra 5-7 mm

3 = Larghezza cucitura tra 6-8 mm

4 = Larghezza cucitura tra 7-9 mm

5 = Larghezza cucitura tra 8-10 mm

Ridurre la largheza del taglio, se il margine

della stoffa si arrotola durante il cucito.

Girare la regolazione del coltello verso 1

(A).

Aumentare la larghezza del taglio se la

formazione del punto è troppo lenta

(vuota). Girare la regolazione del coltello

verso 5 (B).

Adjustments and settings / Regulación y manejo

Réglage et utilisation / Regolazione ed uso

Differential feed

There are two feed dogs one front (C) and one rear (D). The two feed dogs move

independently and the distance each feed dog travels during one complete movement can be

adjusted. The differential feed prevents fluting or waving in knitted or stretch fabrics and

movements between the layers of fabric.

It also ensures pucker-free seams in smooth fabric such as nylon or closely woven fabric.

Perfectly flat seams in knits or stretch fabrics.

The distance travelled by the front feed dog should be greater than that of the rear feed dog.

The front feed dog, therefore, feeds an amount of fabric which the rear feed dog can take

up behind the needle without stretching the fabric. (E)

Pucker - free seams in nylon or closely woven fabrics.

The distance travelled by the rear feed dog should be greater than that of the front feed dog.

The front feed dog, therefore, holds the fabric back so that the rear feed dog can take it up

behind the needle without any puckering. (F)

Adjusting the differential feed

The differential feed can be adjusted by simply turning the differential feed adjustment dial in

the direction desired. Always make a trial run. The differential feed is infinitely variable and

can be adjusted while sewing.

Transporte diferencial

El transporte diferencial está compuesto de dos partes, un transporte delantero (C) y uno trasero

(D). En un movimiento completo cada transporte puede tener un largo de transporte diferente. El

transporte diferencial hace posible la realización de costuras absolutamente rectas y sin

ondulaciones en tejidos de punto, lana, sin que las capas se desplacen. También evita de que las

telas finas como tricot de nilón o tejidos tupidos se fruncen (E).

Costura sin ondulaciones en tricot o tejidos de punto

El arrastre del transporte delantero tiene que ser mayor que del transporte trasero. El

transporte delantero transporta la cantidad de tejido que el transporte trasero es capaz de

tomar detrás de la aguja sin estirarlo.

Ninguna costura fruncida en tejidos tupidos o en tricots de nilón

El arrastre del transporte trasero tiene que ser mayor que el transporte delantero. El transporte

delantero retiene una cantidad de la tela para que el transporte trasero pueda tomar la tela

detrás de la aguja (F).

Regulación del transporte diferencial

El transporte diferencial se regula girando el botón regulador del transporte diferencial.

Hacer siempre una costura de prueba. El transporte diferencial puede regularse a progresión

continua y ajustarse durante la costura.

Entraînement différentiel

La griffe d’entraînement est composée de deux parties, une partie avant (C) et une partie arrière

(D). Lors d’un cycle complet de la griffe d’entraînement, ces deux griffes peuvent avoir des

déplacements de longueur différente. L’entraînement différentiel vous permet d’effectuer des

coutures absolument plates et sans ondulations dans des tissus à mailles, sans décalage des

couches de tissu. Il permet également que les tissus lisses comme le nylon-les tricots ou les

matériels résistants et tissés ne rétrécissent pas durant la couture (E).

Tricot ou lainage sans ondulations

L’avance de la griffe avant doit être plus grande que celle de la griffe arrière. La griffe avant

déplace autant de matériel que la griffe arrière est en mesure d’entraîner derrière l’aiguille.

Aucune couture ne rétrécit sur des étoffes tissées ou des tricots en nylon

L’avance de la griffe arrière doit être plus grande que celle de la griffe avant. La griffe avant retient

alors autant de matériel que la griffe arrière est en mesure d’entraîner derrière l’aiguille (F).

Réglage de l’entraînement différentiel

L’entraînement différentiel se règle en tournant le sélecteur de l’entraînement différentiel.

Prière d’effectuer toujours un essai de couture. L’entraînement différentiel peut se régler

progressivement même pendant la couture.

Trasporto differenziale

La griffa della tagliacuce è composta da una parte anteriore (C) ed una parte posteriore (D).

Le due componenti si muovono indipendentemente e possono avere lunghezze di trasporto

diverse durante un completo movimento della griffa. Il trasporto differenziale permette di

realizzare cuciture assolutamente diritte e senza ondulazioni su materiali elastici.

Il differenziale impedisce inoltre l’effetto arricciato su materiali lisci, come nylon e tricot oppure

stoffe a tessitura compatta (E).

Lavorazione di maglia

La lunghezza di trasporto della griffa anteriore deve essere più grande di quella posteriore.

Così la griffa anteriore mette a disposizione della griffa posteriore tanto materiale quanto

quest’ultima riesce a trasportare senza estendere il materiale.

Stoffe a tessitura compatta, stoffe leggere o maglia di nylon senza effetto

arricciato

La lunghezza di trasporto della griffa posteriore deve essere più grande di quella anteriore.

La quantità di materiale trattenuta dalla griffa anteriore, corrisponde alla quantità che la griffa

riesce a trasportare (F).

Regolazione del trasporto differenziale

La regolazione si effettua girando la manopola del trasporto differenziale. Eseguire sempre

una prova di cucito.

Il trasporto differenziale è regolabile in modo progressivo anche durante la cucitura.

La pagina sta caricando ...

Juki MO-734DE Manuale del proprietario

Marca: Juki

Modello: MO-734DE

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Juki MO-734DE Owner's manual
français: Juki MO-734DE Le manuel du propriétaire
español: Juki MO-734DE El manual del propietario

Juki MO-734DE Manuale del proprietario

Juki MO-734DE Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti