Black & Decker STC1840P C Manuale utente

Categoria
Tagliaerba
Tipo
Manuale utente

Questo manuale è adatto anche per

www.blackanddecker.eu
STC1840P C
14
11
5
7
6
89 32
10
2
3
E
F
C
D
13
10
18
16
16
19
14
15
17
20
20
A
B
12
12
2
3
G
H
I
21
6
J
5˚-10˚
J1
J2
4
5
K
N
O
L M
60cm
J3
7
1 2
23
22
22
O1
O2
4
5
T
P
Q
R
S
24 25
O2
26
27
29
28
6
ENGLISH
(Original instructions)
Intended use
Your BLACK+DECKER STC1840P C trimmers have been
designed for trimming and nishing lawn edges and to cut
grass in conned spaces. This appliance is intended for
consumer use only.
Safety instructions
Warning! When using mains-powered
appliances, basic safety precautions,
including the following, should always be
followed to reduce the risk of re, electric
shock, personal injury and material
damage.
Warning! When using the machine the
safety rules must be followed. For your
own safety and bystanders please read
these instructions before operating the
machine. Please keep the instructions
safe for later use.
u Read all of this manual carefully before
operating the appliance.
u The intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
u Retain this manual for future
reference.
Using your appliance
Always take care when using the
appliance.
u Always use safety glasses or goggles.
u Never operate the machine while
people, especially children, or pets are
nearby.
u Do not allow children or animals to
come near the work area or to touch
the appliance.
u Close supervision is necessary when
the appliance is used near children.
u This appliance is not intended for use
by young or inrm persons without
supervision.
u This appliance is not to be used as a
toy.
u Only use the appliance in daylight or
good articial light.
u Use in a dry location only. Do not allow
the appliance to become wet.
u Avoid using the appliance in bad
weather conditions, especially when
there is a risk of lightning.
u Do not immerse the appliance in water.
u Do not open the body casing. There
are not user-serviceable parts inside.
u Do not operate the appliance in
explosive atmospheres, such as in the
presence of ammable liquids, gases
or dust.
uThe appliance is only to be used with
the power supply unit provided with the
appliance.
Safety of others
u This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
u Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
7
ENGLISH
(Original instructions)
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings.
These risks can arise from misuse,
prolonged use etc.
Even with the application of the
relevant safety regulations and the
implementation of safety devices, certain
residual risks can not be avoided. These
include:
uInjuries caused by touching any
rotating/moving parts.
uInjuries caused when changing any
parts, blades or accessories.
uInjuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
uImpairment of hearing.
uHealth hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
After use
uWhen not in use, the appliance should
be stored in a dry, well ventilated place
out of reach of children.
uChildren should not have access to
stored appliances.
uWhen the appliance is stored or
transported in a vehicle it should be
placed in the boot or restrained to
prevent movement following sudden
changes in speed or direction.
Inspection and repairs
uBefore use, check the appliance
for damaged or defective parts.
Check for breakage of parts and any
other conditions that may affect its
operation.
uDo not use the appliance if any part is
damaged or defective.
uHave any damaged or defective parts
repaired or replaced by an authorised
repair agent.
uNever attempt to remove or replace
any parts other than those specied in
this manual.
Vibration
The declared vibration emission values
stated in the technical data and the
declaration of conformity have been
measured in accordance with a standard
test method provided by EN50636 and
may be used for comparing one tool with
another. The declared vibration emission
value may also be used in a preliminary
assessment of exposure.
Warning! The vibration emission value
during actual use of the power tool can
differ from the declared value depending
on the ways in which the tool is used.
The vibration level may increase above
the level stated.
When assessing vibration exposure to
determine safety measures required by
2002/44/EC to protect persons regularly
using power tools in employment, an
estimation of vibration exposure should
consider, the actual conditions of use and
the way the tool is used, including taking
account of all parts of the operating
cycle such as the times when the tool is
switched off and when it is running idle in
addition to the trigger time.
8
ENGLISH
(Original instructions)
Additional safety instructions for
grass trimmers
Warning! Cutting elements continue to
rotate after the motor is switched off.
uBe familiar with the controls and the
proper use of the appliance.
uAlways remove the battery from the
appliance whenever the appliance
is unattended, before clearing a
blockage, before cleaning and
maintenance, after striking a foreign
object or whenever the appliance
starts vibrating abnormally.
uWear stout shoes or boots to protect
your feet.
uWear long trousers to protect your
legs.
uBefore using the appliance, check that
your cutting path is free from sticks,
stones, wire and any other obstacles.
uOnly use the appliance in the upright
position, with the cutting line near the
ground. Never switch the appliance on
in any other position.
uMove slowly when using the appliance.
Be aware that freshly cut grass is
damp and slippery.
uDo not work on steep slopes. Work
across the face of slopes, not up and
down.
uNever cross gravel paths or roads
while the appliance is running.
uNever touch the cutting line while the
appliance is running.
uDo not put the appliance down until the
cutting line has come to a complete
standstill.
uUse only the appropriate type of
cutting line. Never use metal cutting
line or shing line.
uBe careful not to touch the line
trimming blade.
uKeep hands and feet away from the
cutting line at all times, especially
when switching on the motor.
uBefore using the appliance and after
any impact, check for signs of wear or
damage and repair as necessary.
uNever operate the appliance with
damaged guards or without guards in
place.
uTake care against injury from any
device tted for trimming the lament
line length. After extending new cutter
line always return the machine to
its normal operating position before
switching on.
uAlways ensure that the ventilation slots
are kept clear of debris.
Additional safety instructions for
batteries and chargers
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the
temperature may exceed 40 °C.
uCharge only at ambient temperatures
between 10 °C and 40 °C.
uCharge only using the charger
provided with the tool.
uWhen disposing of batteries, follow
the instructions given in the section
"Protecting the environment".
Chargers
uUse your BLACK+DECKER charger
only to charge the battery in the tool
with which it was supplied. Other
9
ENGLISH
(Original instructions)
batteries could burst, causing personal
injury and damage.
uNever attempt to charge non-
rechargeable batteries.
uHave defective cords replaced
immediately.
uDo not expose the charger to water.
uDo not open the charger.
uDo not probe the charger.
$
The charger is intended for
indoor use only.
Read the instruction manual
before use.
Electrical safety
#
Your charger is double insulated;
therefore no earth wire is
required. Always check that the
mains voltage corresponds to the
voltage on the rating plate. Never
attempt to replace the charger
unit with a regular mains plug.
u If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Labels on appliance
The following pictograms are shown on
the tool along with the date code:
Read the manual prior to
operation.
Wear safety glasses or goggles
when operating this appliance.
Wear suitable ear protectors
when operating this appliance.
Always remove the battery from
the appliance before performing
any cleaning or maintenance.
Beware of ying objects. Keep
bystanders away from the
cutting area.
Do not expose the appliance to
rain or high humidity.
96
Directive 2000/14/EC
guaranteed sound power.
Features
This appliance includes some or all of the following features.
1. Trigger
2. Lock off button
3. Handle
4. Speed control switch
5. Auxiliary handle
6. Height adjust collar
7. Flip to edge collar
8. Trimmer head
9. Edge wheel
10. Guard
11. Spool housing
12. Battery
Charging the battery (Fig. A)
The battery needs to be charged before rst use and
whenever it fails to produce sufcient power on jobs that were
easily done before.
The battery may become warm while charging; this is normal
and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell temperature
warms up or cools down.
u Plug the charger into an appropriate outlet before inserting
the battery pack.
u Insert the battery pack into the charger.
10
ENGLISH
(Original instructions)
The green LED will ash indicating that the battery is being
charged.
The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged and
may be used at this time or left in the charger
Warning! Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished.
Charger diagnostics
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
are indicated by one LED ashing in different patterns.
Bad Battery
The charger can detect a weak or damaged battery. The
red LED ashes in the pattern indicated on the label. If you
see this bad battery blink pattern, do not continue to charge
the battery. Return it to a service centre or a collection site
for recycling
Hot/Cold Pack Delay
When the charger detects a battery that is excessively
hot or excessively cold, it automatically starts a Hot/Cold
Pack delay, suspending charging until the battery has
normalised. After this happens, the charger automatically
switches to the Pack Charging mode. This feature ensures
maximum battery life. The red LED ashes in the pattern
indicated on the label when the Hot/Cold pack delay is
detected.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indenitely. The charger will keep the battery
pack fresh and fully charged.
Important charging notes
u Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack .
u The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer
u If the battery pack does not charge properly:
u Check current at receptacle by plugging in a lamp or
other appliance
u Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
u Move charger and battery pack to a location where the
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
u If charging problems persist, take the appliance, battery
pack and charger to your local service center.
u The battery pack should be recharged when it fails to
produce sufcient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
u Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any buildup
of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply
when there is no battery pack in the cavity. Unplug charger
before attempting to clean.
u Do not freeze or immerse charger in water or any other
liquid.
Warning! Shock hazard. Do not allow any liquid to get inside
charger. Never attempt to open the battery pack for any
reason.
If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
Installing and removing the battery pack from the
appliance
Warning! Make certain the lock-off button is not engaged to
prevent switch actuation before removing or installing battery.
To install battery pack
Insert battery (12) into appliance until an audible click is
heard (Figure B). Ensure battery pack is fully seated and fully
latched into position.
To remove battery pack
Depress the battery release button (13) as shown in Figure C
and pull battery pack out of appliance.
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the battery has been removed.
11
ENGLISH
(Original instructions)
Assembly tools required (not supplied):
Phillips Screwdriver.
Fitting the guard (Fig. D, E)
Warning! Remove the battery from the appliance before
attempting to attach the guard, edge guide or handle. Never
operate appliance without guard rmly in place. The guard
must always be on the appliance to protect the user.
u Remove the screw from the guard.
u Turn the trimmer upside down so that you are looking
down at the spool cap (14).
u Turn the guard (10) upside down and slide it fully onto the
motor housing (15). Make sure the tabs (16) on the guard
engage the ribs (17) on the motor housing as shown.
u Continue to slide the guard on until you hear it “snap” into
place. The locking tab (18) should snap into the housing
slot (19).
u Using a phillips screwdriver, insert the guard screw and
tighten securely as shown in Figure E to complete the
guard assembly.
u Once the guard is installed, remove the covering from the
line cut-off blade, located on the edge of the guard
Warning! Never use the tool unless the guard is properly
tted.
Attaching the auxiliary handle (Fig. F, G, H)
u To attach the handle, press in on the buttons (20) on both
sides of the upper housing as shown in Figure F.
u Position the handle as shown in Figure G (with the
BLACK+DECKER logo facing upward). Partially push the
handle on so it will hold the buttons in when you release
them with your hand.
u Push the handle completely onto the housing and position
it slightly until it “snaps” into place.
u To adjust the handle up or down, press in on the button
(21) and raise or lower the handle (Figure H).
u The handle should be adjusted so that your front arm is
straight when the trimmer is in the working position.
Height adjustment (Fig. I, J–J3)
Warning! Adjust the length of the trimmer to obtain proper
working positions shown in Figures J - J3.
u The overall height of the trimmer can be adjusted by
loosening the height-adjust collar (6) by rotating it in the
direction of the arrow shown in Figure I.
u Move the upper housing straight up or down. When the
desired height is achieved, tighten the collar by rotating it
opposite of the direction shown in Figure I.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
u Remove the tape holding the cutting line to the spool
housing.
Operation
Warning! Always use proper eye protection.
Warning! Before you begin trimming, only use the appropriate
type of cutting line.
Note: Inspect area to be trimmed and remove any wire, cord,
or string-like objects which could become entangled in the
rotating line or spool. Be particularly careful to avoid any wire
which might be bent outwardly into the path of the appliance,
such as barbs at the base of a chain link fence.
Switching on and off
u To switch the appliance on, push the lock-off button (2),
and squeeze the trigger (1).
u To switch the appliance off, release the trigger.
Operating the trimmer (Fig. I, J–J3)
u With the unit on, angle unit and slowly swing the trimmer
side to side as shown in Figure J.
u Maintain a cutting angle of 5° to 10° as shown in
Figure J1. Do not exceed 10° (Figure J2). Cut with the tip
of the line. To keep distance from hard surfaces use edge
wheel (9).
u Maintain a minimum distance of 60 cm between the guard
and your feet as shown in Figure J3. To acheive this
distance adjust the overall height of the trimmer as shown
in Figure I.
Convert to edging mode (Fig. K, L)
Warning! The wheeled edge guide should only be used when
in the edging mode.
The trimmer can be used in trimming mode or edging mode to
trim overhanging grass along lawn edges and ower beds. For
edging, the trimmer head should be in the position shown in
Figure M. If it is not:
u Remove the battery from the trimmer.
u Grasp the ip-to-edge collar (7) and push down as
shown in part 1 of Figure L.
u Rotate the ip-to-edge collar 180° counterclockwise as
shown in part 2, until the handle snaps back into the
upper half of the trimmer.
u To return to trimming position, pull the ip-to-edge collar
down and rotate the head clockwise back to its original
position.
Note: You will experience faster than normal cutting line wear
if the trimmer line is positioned directly over the sidewalk or
abrasive surface.
Edging (Fig. L)
Warning! When being used as an Edger, stones, pieces of
metal and other objects can be thrown out at high speed by
the line. The trimmer and guard are designed to reduce the
danger. However, MAKE SURE that other persons and pets
12
ENGLISH
(Original instructions)
are at least 30 m away. Optimum cutting results are achieved
on edges deeper than 50 mm.
u Do not use this trimmer to create trenches.
u Using the edging wheel (9), guide the trimmer as shown in
Figure I.
u Position the edging wheel on the edge of the sidewalk or
abrasive surface so the cutting line is over the grass or dirt
area to be edged.
u To make a closer cut, slightly tilt the trimmer.
Speed control & runtime extension mode (Fig. M)
This string trimmer gives you the choice to operate at a
more efcient speed to extend the runtime for larger jobs, or
accelerate the trimmer speed for high-performance cutting
(Figure N).
u To extend runtime, pull the speed-control switch back
toward the battery (12) into position #1. This mode is best
for larger projects that require more time to complete.
u To accelerate the trimmer, push the speed-control switch
forward toward the trimmer head (8) into position #2.
This mode is best to cut through heavier growth and for
applications that need higher RPM.
Note: When in acceleration mode (#2), runtime will be
decreased as compared to when trimmer is in extended
runtime mode (#1).
Helpful cutting tips
u Use the tip of the string to do the cutting; do not force
string head into uncut grass. Use edge guide along
such things as fences, houses and ower beds for best
practices.
u Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may
wear string rapidly.
u Do not allow spool cap to drag on ground or other
surfaces.
u In long growth cut from the top down and do not exceed
300 mm high.
u Keep trimmer tilted toward the area being cut; this is the
best cutting area.
u The trimmer cuts when passing the unit from the right to
left. This will avoid throwing debris at the operator.
u Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Cutting line / line feeding
Your trimmer uses 1.65 mm diameter, Round nylon line.
During use, the tips of the nylon lines will become frayed and
worn and the special self feeding spool will automatically feed
and trim a fresh length of line. Cutting line will wear faster and
require more feeding if the cutting or edging is done along
sidewalks or other abrasive surfaces or heavier weeds are
being cut. The advanced automatic line feeding mechanism
senses when more cutting line is needed and feeds and
trims the correct length of line whenever it’s required. Do not
bump unit on ground in attempt to feed line or for any other
purposes.
Clearing jams and tangled line (Figures N, O, P)
Warning! Remove the battery from the trimmer before
making any assembly, adjustments or changing accessories.
Such preventive safety measures reduce the risk of starting
the appliance accidentally. From time to time, especially
when cutting thick or stalky weeds, the line feeding hub may
become clogged with sap or other material and the line will
become jammed as a result. To clear the jam, follow the steps
listed below.
u Remove the battery from the trimmer.
u Press the release tabs (22) on the line spool cap (23),
as shown in Figure O and remove the cap by pulling it
straight off.
u Pull the nylon line spool out and clear any broken line or
cutting debris from the spool area.
u Place spool and line into spool cap with line “parked” in
slots provided as shown in Figure P1.
u Insert the line end through the appropriate hole in the
spool housing. Pull slack line through until it pulls out of
the holding slots as shown in Figure P2.
u Press the spool down gently and rotate it until you feel it
drop into place and then push to snap into place. (When
in place, the spool will turn a few degrees left and right
freely).
u Take care to keep the line from becoming trapped under
the spool.
u Align the spool cap tabs with the slots on the spool
housing.
u Snap the spool cap back on as shown in Figure Q by
depressing lugs and pressing into spool housing.
Note: Make sure that cover is fully positioned, listen for two
audible clicks to ensure both lugs are correctly located. Power
the appliance on. In a few seconds or less you’ll hear the
nylon line being cut automatically to the proper length.
Warning! To avoid appliance damage, if the cutting line
protrudes beyond the trimming blade, cut it off so that it just
reaches the blade.
Note: Other replacement parts (guards, spool caps, etc.) are
available through BLACK+DECKER service centers. To nd
your local service location visit www.blackanddecker.com.
Warning! The use of any accessory not recommended by
BLACK+DECKER for use with this appliance could be
hazardous.
Replacing the spool (Fig. N, O, P, Q)
u Remove battery from appliance.
u Depress the tabs (20) and remove the spool cap (21) from
the spool housing (11) (Figure N).
13
ENGLISH
(Original instructions)
u Grasp empty spool with one hand and spool housing with
other hand and pull spool out.
u If lever (24) (Figure Q) in base of housing becomes
dislodged, replace in correct position before inserting new
spool into housing.
u Remove any dirt and grass from the spool and housing.
u Unfasten the end of the cutting line and guide the line into
the eyelet (O2) Figure O.
u Take the new spool and push it onto the boss (25) (Figure
Q) in the housing. Rotate the spool slightly until it is
seated. The line should protrude approximately 136mm
from the housing.
u Align the tabs on the spool cap with the slots in the
housing (Figure P).
u Push the cap onto the housing until it snaps securely into
place.
Rewinding spool from bulk line (Fig. R, S, T)
Bulk line is also available for purchase from your local retailer.
Note: Hand wound spools from bulk line are likely to become
tangled more frequently than BLACK+DECKER factory
wound spools. For best results, factory wound spools are
recommended. To install bulk line, follow the steps below:
u Remove battery from appliance.
u Remove the empty spool from the appliance as described
in “Replacing the spool.”
u Remove any remaining cutting line from the spool.
u Make a fold at the end of the cutting line at about 19 mm
(26). Feed the cutting line into one of the line anchoring
slots (27) as shown in Figure R.
u Insert the 19 mm end of the bulk line into the hole (30) in
the spool adjacent to the slot as shown in Figure S. Make
sure the line is pulled tight against the spool as shown in
Figure T.
u Wind the cutting line onto the spool in the direction of the
arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross (Figure T).
u When the wound cutting line reaches the recesses (29),
cut the line (Figure S).
u Fit the spool onto the appliance as described in “Replacing
the spool”.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
uRegularly clean the cutting line and spool using a soft
brush or dry cloth.
u Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Troubleshooting
Problem Solution
Appliance runs
slowly.
Remove battery from trimmer.
Check that the spool housing can rotate freely. Carefully
clean it if necessary.
Check that the cutting line does not protrude more than
approximately 122 mm from the spool. If it does, cut it off
so that it just reaches the line trimming blade
Automatic line
feed does not
feed line.
More line is fed when the line shortens to approximately
76 mm. To determine if the line is not feeding, let line
wear past this point.
Keep the tabs depressed and remove the spoolcap with
the spool from the spool housing in the trimmer head.
Ensure that the line is not crisscrossed on the spool as
detailed in (Fig. T). If it is unwind the cutting line and
rewind it neatly.
Inspect tracks at the bottom of spool for damage. If
damaged, replace spool.
Pull the cutting line until it protrudes approximately
122 mm from the spool. If insufcient cutting line is left
on the spool, install a new spool of cutting line.
Align the tabs on the spool cap with the cut outs in the
housing.
Push the spool cap onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade. If the automatic
line feed still does not work or the spool is jammed, try
the following suggestions:
Carefully clean the spool and housing.
Make sure you are using correct line size and diameter
(2.00 mm) - smaller and larger line sizes will affect the
functionality of the auto feed system.
Remove the spool and check if the lever in the spool
housing can move freely.
Remove the spool and unwind the cutting line, then wind
it on neatly again. Replace the spool into the housing.
Overfeeding Ensure you are cutting with the tip of the line 177 mm
from the spool. Use the edge guide if needed to ensure
proper space is maintained.
Ensure you are not exceeding a 10º angle as shown in
(Fig. M). Avoid contact of the line with hard surfaces such
as brick, concrete, wood etc. This will prevent excessive
wear and/or overfeed of line. Cut with the tip of the line
Line unravels
when cap or
spool is
removed
Make sure to park the lines in holding slots (Figure R)
before removing.
14
ENGLISH
(Original instructions)
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
STC1840P C H2
Input Voltage
V
AC
18V
No-Load Speed
min
-1
5500 - 7400
Weight
kg 2.55
Battery BL4018
Voltage
V
DC
18V
Capacity Ah
4.0
Type Li-Ion
Charger 906068**
Input Voltage
V
AC
230V
Output Voltage
V
DC
18V
Current mA 2000
Hand/arm weighted vibration value according to
EN50636-2-91:
= < 2.5 m/s
2
, uncertainty (K) = 1.5 m/s
2
.
L
PA
(sound pressure) 79 dB(A), uncertainty (K) = 3 dB(A)
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
STC1840P C
Cordless String Trimmer
Black & Decker declares that these products described under
"technical data" are in compliance with:
EN60335-1:2012+A11:2014 EN50636-2-91:2014
2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VI
DEKRA Certication B.V. Meander 1051 / P.O. Box 5185
6825 MJ ARNHEM / 6802 ED ARNHEM, Netherlands
Notied Body ID No.: 0344
Level of sound power according to 2000/14/EC
(Article 12, Annex III, L ≤ 50 cm):
L
WA
(measured sound power) 93 dB(A)
uncertainty (K) = 3 dB(A)
L
WA
(guaranteed sound power) 96 dB(A)
These products also comply with Directive
2006/42/EC, 2014/30/EU and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
le and makes this declaration on behalf of Black & Decker.
A. P. Smith
Technical Director
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
18/02/2019
Guarantee
Black & Decker is condent of the quality of its products
and offers consumers a 24 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Black & Decker Terms and Conditions and you will need
to submit proof of purchase to the seller or an authorised
repair agent. Terms and conditions of the Black & Decker 2
year guarantee and the location of your nearest authorised
repair agent can be obtained on the Internet at www.2helpU.
com, or by contacting your local Black & Decker ofce at the
address indicated in this manual.
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and receive updates on new
products and special offers.
15
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
Verwendungszweck
Ihr BLACK+DECKER Rasentrimmer STC1840P C wurde
für das Trimmen und Zuschneiden von Rasenkanten sowie
für das Schneiden von Gras in beengten Platzverhältnissen
entwickelt. Dieses Gerät ist nicht für den gewerblichen Einsatz
vorgesehen.
Sicherheitshinweise
Warnung! Beachten Sie beim Umgang
mit netzstrombetriebenen Geräten stets
die grundlegenden Sicherheitshinweise,
die im Folgenden beschrieben werden.
Dadurch verhindern Sie Brände,
Stromschläge sowie Sach- und
Personenschäden.
Warnung! Beachten Sie beim
Verwenden des Geräts unbedingt die
Sicherheitsregeln. Lesen Sie zu Ihrer
eigenen Sicherheit und zum Schutz
in der Nähe bendlicher Personen vor
Gebrauch des Geräts die folgende
Bedienungsanleitung. Heben Sie diese
Anleitung zur späteren Verwendung gut
auf.
uLesen Sie diese Anleitung vollständig
und aufmerksam durch, bevor Sie das
Gerät verwenden.
uDer vorgesehene Verwendungszweck
ist in dieser Anleitung beschrieben.
Bei Verwendung von Zubehör oder
Anbauteilen, die nicht in dieser
Anleitung empfohlen werden, sowie
bei der Verwendung des Geräts
in Abweichung von den in dieser
Anleitung beschriebenen Verfahren
besteht Verletzungsgefahr.
uBewahren Sie diese Anleitung auf.
Verwendung des Geräts
Verwenden Sie das Gerät stets mit
Umsicht.
uTragen Sie stets eine Schutzbrille.
uEs sollte stets ein Sicherheitsabstand
zu anderen Personen, insbesondere
Kindern, und Haustieren eingehalten
werden.
uAchten Sie darauf, dass sich im
Arbeitsbereich keine Kinder oder Tiere
aufhalten. Verhindern Sie, dass Kinder
das Gerät berühren.
uSeien Sie besonders vorsichtig, wenn
Sie das Gerät in der Nähe von Kindern
verwenden.
uDas Gerät ist nicht für die
unbeaufsichtigte Verwendung durch
Kinder oder gebrechliche Personen
vorgesehen.
uDas Gerät ist kein Spielzeug.
uBetreiben Sie das Gerät nur bei
Tageslicht oder bei ausreichender
Beleuchtung.
uVerwenden Sie das Gerät nur in
trockener Umgebung. Achten Sie
darauf, dass das Gerät nicht nass
wird.
uVermeiden Sie, das Gerät bei
schlechtem Wetter zu verwenden, vor
allem, wenn das Risiko von Gewitter
besteht.
uTauchen Sie das Gerät nicht in
Wasser.
uVersuchen Sie nicht, das Gehäuse zu
öffnen. Im Inneren benden sich keine
zu wartenden Teile.
uBetreiben Sie das Gerät nicht in
explosionsgefährdeter Umgebung,
in der sich brennbare Flüssigkeiten,
Gase oder Staub benden.
uDas Gerät darf nur mit dem im
Lieferumfang enthaltenen Netzteil
betrieben werden.
16
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
uSchwerhörigkeit.
uGesundheitsrisiken durch das
Einatmen von Staub beim Gebrauch
des Geräts (z. B. bei Holzarbeiten,
insbesondere Eiche, Buche und
Pressspan)
Nach dem Gebrauch
uBewahren Sie das Gerät bei
Nichtgebrauch an einem trockenen,
gut belüfteten Ort außerhalb der
Reichweite von Kindern auf.
uKinder sollten keinen Zugang zu
aufbewahrten Geräten haben.
uWenn das Gerät in einem Fahrzeug
transportiert oder gelagert wird,
bewahren Sie es im Kofferraum oder
einer geeigneten Ablage auf, damit
es bei plötzlichen Geschwindigkeits-
oder Richtungsänderungen nicht in
Bewegung geraten kann.
Inspektion und Reparaturen
uPrüfen Sie das Gerät vor der
Verwendung auf beschädigte
oder defekte Teile. Prüfen Sie, ob
Teile beschädigt sind oder andere
Bedingungen vorliegen, die die
Funktion beeinträchtigen können.
uBetreiben Sie das Gerät nicht, wenn
Teile beschädigt oder defekt sind.
uLassen Sie beschädigte oder defekte
Teile in einer Vertragswerkstatt
reparieren oder austauschen.
uErsetzen oder entfernen Sie keine
Teile, für die in dieser Anleitung
keine entsprechende Beschreibung
enthalten ist.
Sicherheit anderer Personen
u Dieses Gerät darf von Kindern
ab 8 Jahren und Personen mit
eingeschränkten körperlichen,
sensorischen oder geistigen
Fähigkeiten sowie mangelnder
Erfahrung und Wissen in Bezug auf
dessen Gebrauch bedient werden,
wenn sie bei der Verwendung des
Geräts beaufsichtigt oder angeleitet
werden und die möglichen Gefahren
verstehen.
u Kinder dürfen nicht mit dem
Gerät spielen. Reinigung und
Wartungsarbeiten dürfen von Kindern
nur unter Aufsicht durchgeführt
werden.
Restrisiken
Beim Gebrauch dieses Geräts
verbleiben zusätzliche Restrisiken,
die möglicherweise nicht in den
Sicherheitswarnungen genannt werden.
Diese Risiken bestehen beispielsweise
bei Missbrauch oder längerem Gebrauch.
Auch bei der Einhaltung der
entsprechenden Sicherheitsvorschriften
und der Verwendung aller
Sicherheitsgeräte bestehen weiterhin
bestimmte Restrisiken. Diese sind:
uVerletzungen, die durch das Berühren
von sich drehenden/bewegenden
Teilen verursacht werden.
uVerletzungen, die durch das
Austauschen von Teilen, Messern oder
Zubehör verursacht werden.
uVerletzungen, die durch längeren
Gebrauch eines Geräts verursacht
werden. Legen Sie bei längerem
Gebrauch regelmäßige Pausen ein.
17
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
Vibration
Die in den Abschnitten „Technische
Daten“ und „EU-Konformitätserklärung“
angegebenen Werte für die
Vibrationsemission wurden mit einer
Standard-Prüfmethode nach EN50636
ermittelt und können zum Vergleich
verschiedener Geräte herangezogen
werden. Außerdem kann mit Hilfe dieses
Werts die Belastung bei Verwendung des
Geräts schon im Voraus eingeschätzt
werden.
Warnung! Die bei Verwendung des
Geräts auftretende Vibrationsemission
hängt von der Art des Gerätegebrauchs
ab und kann dementsprechend von
dem angegebenen Wert abweichen.
Gegebenenfalls kann die Vibration über
dem angegebenen Wert liegen.
Für die Ermittlung der
Vibrationsbelastung müssen die
tatsächlichen Einsatzbedingungen
und Verwendungen des Geräts
während des gesamten Arbeitsgangs
berücksichtigt werden, einschließlich
der Zeiten, wenn das Gerät nicht
verwendet oder im Leerlauf betrieben
wird. Diese Werte werden benötigt, um
die gemäß 2002/44/EG erforderlichen
Sicherheitsmaßnahmen zum Schutz von
Personen festlegen zu können.
Zusätzliche Sicherheitshinweise
für Rasentrimmer
Warnung! Die Schneidevorrichtung
rotiert nach Abschalten des Geräts einige
Sekunden lang weiter.
uMachen Sie sich mit den
Bedienelementen und dem
ordnungsgemäßen Gebrauch des
Geräts vertraut.
uEntfernen Sie den Akku aus dem
Gerät, wenn es nicht beaufsichtigt
wird, bevor eine Blockierung
beseitigt wird, vor Reinigungs- und
Wartungsarbeiten sowie nachdem ein
Fremdkörper getroffen wurde oder
wenn das Gerät mit ungewöhnlichen
Vibrationen startet.
uTragen Sie stabile Schuhe oder Stiefel,
um Ihre Füße zu schützen.
uTragen Sie lange Hosen, um Ihre
Beine zu schützen.
uVergewissern Sie sich vor
Verwenden des Geräts, dass die zu
beschneidende Fläche frei von Ästen,
Steinen, Draht und anderen Objekten
ist.
uVerwenden Sie das Gerät
ausschließlich in aufrechter Stellung
und mit Schneidfaden in Bodennähe.
Schalten Sie das Gerät keinesfalls in
einer anderen Stellung ein.
uAchten Sie bei Verwendung des
Geräts auf langsame Bewegungen.
Achten Sie darauf, dass frisch
gemähtes Gras feucht und rutschig
sein kann.
uArbeiten Sie nie an steilen Hängen.
Schieben Sie das Gerät immer parallel
zum Hang, nie den Hang hinauf oder
hinunter.
uSchalten Sie das Gerät vor dem
Überqueren von Kieswegen und
Straßen aus.
uBerühren Sie niemals den
Schneidfaden, während sich das Gerät
in Betrieb bendet.
18
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
uWarten Sie stets, bis der Schneidfaden
vollständig zum Stillstand gekommen
ist, bevor Sie das Gerät absetzen.
uVerwenden Sie ausschließlich
geeignete Schneidfäden. Verwenden
Sie keinesfalls Schneidfäden aus
Metall oder Angelschnur.
uBerühren Sie auf keinen Fall das
Fadenschneidemesser.
uHalten Sie Hände und Füße stets vom
Schneidfaden fern, insbesondere beim
Einschalten des Geräts.
uÜberprüfen Sie das Gerät vor
Gebrauch und nach Stößen auf
Beschädigungen und Verschleiß,
und veranlassen Sie notwendige
Reparaturmaßnahmen.
uBetreiben Sie keinesfalls das Gerät,
wenn die Schutzvorrichtungen
beschädigt oder nicht ordnungsgemäß
angebracht sind.
uSchützen Sie sich vor Verletzungen
beim Verwenden von Geräten zum
Verkürzen des Schneidfadens.
Bringen Sie nach Herausziehen des
neuen Schneidfadens das Gerät
vor dem Einschalten in die normale
Betriebsposition.
uStellen Sie stets sicher, dass
die Lüftungsschlitze frei von
Verschmutzungen sind.
Zusätzliche Sicherheitshinweise
für Akkus und Ladegeräte
Akkus
uKeinesfalls versuchen, den Akku zu
öffnen.
uAchten Sie darauf, dass der Akku nicht
mit Wasser in Berührung kommt.
uNicht bei Temperaturen über 40 °C
lagern.
uLaden Sie den Akku ausschließlich bei
Umgebungstemperaturen zwischen 10
°C und 40 °C.
uVerwenden Sie ausschließlich das
mitgelieferte Ladegerät.
uBei der Entsorgung von Akkus oder
Batterien die Hinweise im Abschnitt
"Umweltschutz" beachten.
Ladegeräte
uVerwenden Sie das BLACK+DECKER
Ladegerät nur für den Akku des
Werkzeugs, mit dem es geliefert
wurde. Andere Akkus können platzen
und Sachschäden oder Verletzungen
verursachen.
uVersuchen Sie keinesfalls, nicht
auadbare Batterien zu laden.
uLassen Sie beschädigte Kabel sofort
austauschen.
uAchten Sie darauf, dass das Ladegerät
nicht mit Wasser in Berührung kommt.
uVersuchen Sie nicht, das Ladegerät zu
öffnen.
uNehmen Sie am Ladegerät keine
Veränderungen vor.
$
Das Ladegerät darf nur im
Innenbereich verwendet werden.
Vor Gebrauch die Anleitung
lesen.
19
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
Elektrische Sicherheit
#
Das Ladegerät ist schutzisoliert,
daher ist keine Erdleitung
erforderlich. Stellen Sie sicher,
dass die Netzspannung der auf
dem Typenschild des Geräts
angegebenen Spannung
entspricht. Ersetzen Sie das
Ladegerät keinesfalls durch ein
normales Netzkabel.
u Bei einer Beschädigung des
Netzkabels muss dieses durch den
Hersteller oder eine BLACK+DECKER
Vertragswerkstatt ausgetauscht
werden, um mögliche Gefahren zu
vermeiden.
Warnsymbole am Gerät
Am Gerät sind die folgenden
Piktogramme inkl. Datumscode
angebracht:
Lesen Sie vor Inbetriebnahme
die Bedienungsanleitung.
Tragen Sie eine Schutzbrille,
wenn Sie mit dem Gerät
arbeiten.
Tragen Sie einen geeigneten
Gehörschutz, wenn Sie mit dem
Gerät arbeiten.
Entfernen Sie den Akku aus dem
Gerät, bevor Reinigungs- oder
Wartungsarbeiten durchgeführt
werden.
Achten Sie auf Gegenstände,
die eventuell umhergeschleudert
werden. Halten Sie andere
Personen von der Schneidzone
fern.
Schützen Sie das Gerät vor
Feuchtigkeit und Regen.
96
Garantierter Schalldruckpegel,
gemessen nach Richtlinie
2000/14/EG.
Merkmale
Dieses Gerät verfügt über einige oder alle der folgenden
Merkmale.
1. Auslöser
2. Einschaltsperre
3. Griff
4. Geschwindigkeitsschalter
5. Zusatzgriff
6. Stellring für die Höhenanpassung
7. Stellring zum Umstellen der Schnittführung
8. Trimmerkopf
9. Kantenrad
10. Schutzhaube
11. Spulengehäuse
12. Akku
Laden des Akkus (Abb. A)
Der Akku muss vor der erstmaligen Benutzung sowie immer
dann aufgeladen werden, wenn das Gerät nicht mehr mit
voller Leistung arbeitet.
Der Akku kann sich während des Auadens erwärmen. Das ist
normal und deutet nicht auf ein Problem hin.
Warnung! Laden Sie den Akku nicht, wenn die
Umgebungstemperatur unter 10 °C oder über 40 °C liegt.
Empfohlene Ladetemperatur: ca. 24 °C.
Hinweis: Ein Akku, bei dem die Temperatur der Akkuzellen
unter ca. 10 °C oder über 40 °C liegt, wird vom Ladegerät
nicht geladen.
Lassen Sie in diesem Fall den Akku im Ladegerät. Das
Ladegerät beginnt automatisch mit dem Ladevorgang, sobald
sich die Zellen erwärmt bzw. abgekühlt haben.
u Setzen Sie das Ladegerät in eine geeignete Steckdose
ein, bevor Sie den Akku einsetzen.
u Setzen Sie den Akku in das Ladegerät ein.
Die grüne LED blinkt, wenn der Akku geladen wird.
20
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
Der Abschluss des Ladevorgangs wird dadurch
angezeigt, dass die grüne LED dauerhaft leuchtet. Der
Akku ist vollständig aufgeladen und kann jetzt verwendet
oder in der Ladestation gelassen werden.
Warnung! Laden Sie entladene Akkus so bald wie
möglich nach dem Gebrauch wieder auf, da sonst die
Batterielebensdauer stark verringert werden kann.
Diagnose des Ladegeräts
Das Ladegerät ist so konzipiert, dass es bestimmte Probleme
erkennen kann, die am Akku oder der Stromquelle auftreten
können. Probleme werden dadurch angezeigt, dass eine LED
in verschiedenen Sequenzen blinkt.
Defekter Akku
Das Ladegerät kann einen schwachen oder beschädigten
Akku erkennen. Die rote LED blinkt mit dem Muster, das
auf dem Etikett angegeben ist. Wenn das Blinkmuster für
einen defekten Akku zu sehen ist, laden Sie den Akku nicht
weiter auf. Bringen Sie ihn zu einem Kundendienstzentrum
oder einer Recycling-Sammelstelle.
Verzögerung heißer/kalter Akku
Wenn das Ladegerät erkennt, dass ein Akku übermäßig
heiß oder kalt ist, startet es automatisch eine „Verzögerung
heißer/kalter Akku“, bis sich der Akku normalisiert hat.
Danach schaltet das Ladegerät automatisch in den
Akku-Lademodus. Diese Funktion gewährleistet eine
maximale Lebensdauer des Akkus. Die rote LED blinkt mit
dem Muster, das auf dem Etikett angegeben ist, wenn die
„Verzögerung heißer/kalter Akku“ erkannt wird.
Belassen des Akkus im Ladegerät
Sie können den Akku auch im Ladegerät belassen. In diesem
Fall leuchtet die LED-Anzeige dauerhaft. Das Ladegerät hält
den Akku in einem vollständig geladenen Zustand.
Wichtige Hinweise zum Auaden
u Die längste Lebensdauer und beste Leistung wird
erhalten, wenn der Akku bei einer Lufttemperatur
zwischen 18°und 24°C aufgeladen wird. Laden Sie den
Akku NICHT bei einer Umgebungstemperatur unter
+4,5°C oder über +40,5°C auf. Dies ist wichtig und
verhindert schwere Schäden am Akku.
u Das Ladegerät und der Akku können sich während des
Ladevorgangs warm anfühlen. Dies ist ein normaler
Zustand und weist nicht auf ein Problem hin. Um das
Abkühlen des Akkus nach dem Gebrauch zu erleichtern,
platzieren Sie das Ladegerät und den Akku nicht in
einer warmen Umgebung, wie beispielsweise in einem
Metallschuppen oder einem nicht isolierten Wohnwagen.
u Wenn der Akku nicht richtig aufgeladen wird:
u Prüfen Sie, ob die Steckdose unter Spannung steht,
indem Sie eine Lampe oder ein anderes Gerät an die
Steckdose anschließen.
u Überprüfen Sie, ob die Steckdose mit einem
Lichtschalter verbunden ist, der auch das Gerät
ausschaltet, wenn das Licht ausgeschaltet wird.
u Bringen Sie Ladegerät und Akku an einen Ort, wo die
Umgebungstemperatur ca. 18°-24°C beträgt.
u Wenn die Ladeprobleme bestehen bleiben, bringen Sie
Gerät, Akku und Ladegerät zu Ihrer lokalen
Vertragswerkstatt.
u Der Akku sollte aufgeladen werden, wenn das Gerät
nicht mehr die volle Leistung bringt. Betreiben Sie das
Werkzeug in diesem Fall NICHT WEITER. Befolgen Sie
die Anweisungen bezüglich des Auadens. Sie können
auch jederzeit einen teilweise entleerten Akku auaden,
ohne dass dies nachteilige Auswirkungen auf den Akku
hat.
u Leitfähige Fremdmaterialien, z.B. unter anderem
Stahlwolle, Alufolie oder angesammelte Metallpartikel,
sollten von Hohlräumen des Ladegeräts ferngehalten
werden. Ziehen Sie den Netzstecker des Ladegerätes
immer aus der Steckdose, wenn kein Akku in der
Vertiefung steckt. Ziehen Sie den Netzstecker des
Ladegerätes vor dem Reinigen aus der Steckdose.
u Gerät keinem Spritzwasser aussetzen oder in Wasser
oder andere Flüssigkeiten tauchen.
Warnung! Stromschlaggefahr. Keine Flüssigkeiten in das
Ladegerät gelangen lassen. Keinesfalls versuchen, den Akku
zu öffnen.
Wenn das Kunststoffgehäuse des Akkus Brüche oder
Risse aufweist, bringen Sie es zum Recycling zu einer
Vertragswerkstatt.
Anbringen und Entfernen des Akkus
Warnung! Der Verriegelungsknopf muss eingerastet sein,
damit keine unbeabsichtigte Bedienung des Ein-/Aus-
Schalters vor dem Anbringen bzw. Entfernen des Akkus
erfolgen kann.
Anbringen des Akkus
Setzen Sie den Akku (12) in das Gerät ein, bis ein Klicken
zu hören ist (Abbildung B). Stellen Sie sicher, dass der Akku
vollständig eingesetzt und eingerastet ist.
1 / 1

Black & Decker STC1840P C Manuale utente

Categoria
Tagliaerba
Tipo
Manuale utente
Questo manuale è adatto anche per