RCF TX 4016 Manuale del proprietario

Marca: RCF

Modello: TX 4016

Categoria: Microfoni

Tipo: Manuale del proprietario

OWNER MANUAL

MANUALE D’USO

TX 4016

PX 4116

- UHF DIVERSITY WIRELESS

MICROPHONES

- RADIOMICROFONI UHF

“DIVERSITY”

INDEX

INDICE

ENGLISH

SAFETY PRECAUTIONS

DESCRIPTION

RX 4016 RECEIVER RACK MOUNTING

RX 4016 FRONT PANEL

RX 4016 REAR PANEL

RX 4016 OPERATION

TX 4000 TRANSMITTER / HANDHELD DYNAMIC MICROPHONE

PX 4100 BODY PACK TRANSMITTER

TX 4000 / PX 4100 TRANSMITTER OPERATION

FREQUENCIES

SPECIFICATIONS

ITALIANO

AVVERTENZE PER LA SICUREZZA

DESCRIZIONE

INSTALLAZIONE A RACK (19”) DEI RICEVITORI RX 4016

RX 4016 – PANNELLO FRONTALE

RX 4016 - PANNELLO POSTERIORE

FUNZIONAMENTO DEL RICEVITORE RX 4016

TRASMETTITORE AD IMPUGNATURA TX 4000 CON MICROFONO DINAMICO

TRASMETTITORE PER CINTURA PX 4100

FUNZIONAMENTO DEI TRASMETTITORI TX 4000 / PX 4100

FREQUENZE

DATI TECNICI

ENGLISH

IMPORTANT NOTES

Before connecting and using this product, please read this instruction manual carefully and

keep it on hand for future reference. The manual is to be considered an integral part of

this product and must accompany it when it changes ownership as a reference for correct

installation and use as well as for the safety precautions.

RCF S.p.A. will not assume any responsibility for the incorrect installation and / or use of

this product.

WARNING: To prevent the risk of ﬁre or electric shock, never expose these products to

rain or humidity.

SAFETY PRECAUTIONS

1. All the precautions, in particular the safety ones, must be read with special attention, as

they provide important information.

2. Use the dedicated adapter only. Verify the mains voltage corresponds to the voltage shown

on the adapter rating plate and the adapter output voltage value and type (direct / alternating)

corresponds to the product input voltage. If not, please contact your RCF dealer.

Check also that the adapter has not been damaged due to possible clashes / hits or

overloads.

The mains voltage, which the adapter is connected to, is sufﬁciently high to involve a risk

of electrocution: pay attention during the connection (i.e. never do it with wet hands) and

never open the adapter.

Make sure that the adapter cable is not (or cannot be) stepped on or crushed by other

objects (pay particular attention to the cable part near the plug and the point where it

leads out from the adapter).

3. Make sure that no objects or liquids can get into these products, as this may cause a

short circuit.

All devices shall not be exposed to dripping or splashing. No objects ﬁlled with liquid (such

as vases) and no naked sources (such as lighted candles) shall be placed on receivers.

4. Never attempt to carry out any operations, modiﬁcations or repairs that are not expressly

described in this manual.

Contact your authorized service centre or qualiﬁed personnel should any of the following

occur:

-The product does not function (or functions in an anomalous way)

-The adapter or its power supply cable has been damaged

-Objects or liquids have got into the unit

-The product has been subject to a heavy impact.

5. If this product is not used for a long period, unplug the receiver adapter and remove all

batteries from the transmitter.

6. If a product begins emitting any strange odours or smoke, switch it off immediately,

unplug the receiver adapter and/or remove batteries from the transmitter.

7. Do not connect this product to any equipment or accessories not foreseen.

Check the suitability of the surface on which the receiver is placed, considering (for example)

the mechanical vibrations normally generated by transducers.

To prevent the risk of falling equipment, do not stack more receivers.

8. RCF S.p.A. strongly recommends this product is only installed by professional qualiﬁed

installers (or specialised ﬁrms) who can ensure correct installation and certify it according

to the regulations in force. The entire audio system must comply with the current standards

and regulations regarding electrical systems.

IMPORTANT NOTES

WARNING

SAFETY

PRECAUTIONS

ENGLISH

9. Supports and trolleys

The equipment should be only used on trolleys or supports, where necessary, that are

recommended by the manufacturer.

The equipment / support / trolley assembly must be moved with extreme caution.

Sudden stops, excessive pushing force and uneven ﬂoors may cause the assembly to

overturn.

10. There are numerous mechanical and electrical factors to be considered when installing

a professional audio system (in addition to those which are strictly acoustic, such as sound

pressure, angles of coverage, frequency response, etc.).

11. Hearing loss

Exposure to high sound levels can cause permanent hearing loss.

The acoustic pressure level that leads to hearing loss is different from person to person and

depends on the duration of exposure. To prevent potentially dangerous exposure to high

levels of acoustic pressure, anyone who is exposed to these levels should use adequate

protection devices.

When using a transducer capable of producing high sound levels, it is necessary to wear

ear plugs or protective earphones.

See the technical speciﬁcations in the instruction manual for the maximum sound pressure

loudspeakers are capable of producing.

12. To prevent the occurrence of noise on the cables that carry microphone signals or line

signals (for example, 0 dB), only use screened cables and avoid running them in the vicinity of:

-Equipment that produces high-intensity electromagnetic ﬁelds

-Mains cables

-Loudspeaker lines.

13. Do not point microphones at near loudspeakers (in order to avoid feedback).

14. Place the receiver far from any heat sources and always ensure adequate air

circulation.

15. Never force the control elements (keys, knobs, etc. ).

16. Do not use solvents, alcohol, benzene or other volatile substances for cleaning external

parts. Clean with a dry cloth only.

NOTES ABOUT BATTERIES

1. Use non-rechargeable AA type (1.5 V) batteries, better if alkaline and new.

2. Do NOT use old and new batteries at the same time.

3. Do NOT put together different models of batteries.

4. Do NOT attempt to charge non rechargeable batteries.

5. Verify the polarity of batteries is correct (inserted properly, following the indication on

the relevant compartment).

6. Remove batteries when empty or in the case the device will not be used for a

long time.

7. Do NOT short-circuit batteries (i.e. connecting the 2 opposite poles together with

metallic wires).

8. Throw empty batteries into dedicated garbage cans, according to your country laws

about ecology and environment protection.

9. Never dispose of batteries in the ﬁre or immerse in water.

NOTES ABOUT BATTERIES

ENGLISH

RCF S.P.A. THANKS YOU FOR PURCHASING THIS PRODUCT, WHICH HAS BEEN

DESIGNED TO GUARANTEE RELIABILITY AND HIGH PERFORMANCE.

DESCRIPTION

TX 4016 and PX 4116 are UHF wireless microphones.

Each receiver has 2 antennas for smart switching diversity control (the higher level

radio signal is automatically selected), greater reliability and coverage, reduced risks of

breakdowns and interferences.

The operating frequency of the transmitter can be automatically searched thanks to the

receiver auto-scan function.

Of course, it is possible to match the transmitter channel to the receiver one manually.

144 channels are available (12 groups, each with 12 different frequencies).

It is possible to use up to 16 channels simultaneously (when having 16 wireless

microphones).

TX 4016 kit consists of:

-a RX 4016 receiver (with AC / DC adapter, 2 antennas and a 1.5 m cable with 1/4”

jack plugs)

-a TX 4000 transmitter / handheld dynamic microphone

PX 4116 kit consists of:

-a RX 4016 receiver (with AC / DC adapter, 2 antennas and a 1.5 m cable with 1/4”

jack plugs)

-a PX 4100 body pack transmitter

-a LA 2004 ‘Lavalier’ (tie-clip) electret microphone

FEATURES

COMMON

-PLL (phase-locked loop) UHF

-Use of up to 16 channels / frequencies (out of 144) simultaneously

RX 4016 diversity receiver

-Friendly user interface with front panel LCD display

-Auto-scan function for easy operation

-RF signal switching ‘diversity’ control

-3 output level selection

-Squelch control

TX 4000 / PX 4100 transmitters

-Soft-touch painting for comfortable use

-3 RF output power level selection

-Mute function

-Lock function

FEATURES

ENGLISH

Each single RX 4016 receiver can be normally placed on a desk (or a table, on the rack

cabinet top, etc.).

The optional RCF AR 1620 rack mounting accessory allows to mount a single or a pair of

RX 4016 receivers into a 19” rack cabinet (1 unit).

RX 4016 RECEIVER RACK MOUNTING

RX 4016 FRONT PANEL

1 POWER switch to turn the RX 4016 receiver on/off.

2 UP key: it increases the value of the selected parameter

(chosen through the MENU key 4).

3 DOWN key: it decreases the value of the selected parameter

(chosen through the MENU key 4).

4 MENU key: press once or more times to select the parameter to edit.

5 MEM key

-Press once (and immediately release) to store the new settings (when editing).

-Press and hold (1 second) to start the auto-scan.

6 LCD Display

The LCD display shows both radio (RF) and audio (AF) signals, remaining battery life of

the transmitter, selected group – channel – frequency.

See the ‘RX 4016 operation’ manual section for detailed information.

3 6 1

ENGLISH

7 BALANCED AUDIO OUTPUT

XLR connector:

1 – ground

2 – audio signal (hot, +)

3 – audio signal (cold, –)

8 UNBALANCED AUDIO OUTPUT

6.3 mm (¼”) ‘TS’ jack connector:

9 POWER SUPPLY INPUT

Connect the output of the included power supply unit (15 V dc) to this input.

0 ANT-A, ANT-B antenna inputs

Inputs for the included antennas (or remote antennas, not included).

RX 4016 REAR PANEL

1 2

–

GND 3

UNBALANCED SIGNAL (TS JACK)

sleeve (gnd)tip

tip = signal

UHF RECEIVER +

AUDIO OUTPUT

BALANCED

Power Supply Input

12-18 V 300 mA

UN-BALANCED

POWER

Serial N°:

ANT-B ANT-A

RX4016

7 8 9

P P

ENGLISH

RX 4016 OPERATION

1 Selected frequency group (1 ÷ 12)

2 Selected channel (1 ÷ 12)

3 Mute function

4 Frequency (MHz) corresponding to the selected channel

5 Transmitter remaining battery life

6 AF: bar graph indicating the received audio level

7 RF: bar graph indicating the ﬁeld strength of the received radio signal

AUTO-SCAN

Press and hold the MEM 5 key for one second to start the auto-scan function, which

automatically searches the current transmitter carrier frequency in the entire band.

During the search, the display shows the channel sequence and the audio output

is muted. As soon as the transmitter frequency is found, the scan will be stopped

automatically and the current channel / frequency will be ﬂashing. At this point, press the

MEM key to store the new channel.

Note: in some cases, it may be necessary to select the channel manually

(see the next ‘manual channel selection’).

MANUAL CHANNEL SELECTION

Press the MENU 4 key: on display ‘GROUP’ is now flashing and it is possible to

select the group through the UP 2 / DOWN 3 keys.

When the group is set, press the MEM 5 key to store the new setting (or the MENU

4 key to cancel).

Then press the MENU 4 key twice (sequentially): on display ‘CHANNEL’ is now

flashing and it is possible to select the channel through the UP 2 / DOWN 3 keys.

When the channel is set, press the MEM 5 key to store the new setting (or the

MENU 4 key to cancel).

AUDIO OUTPUT LEVEL ADJUSTING (balanced audio output 7 only)

Press the MENU 4 key 3 times (sequentially): the display indicates ‘PL’ and a value.

Use the UP 2 / DOWN 3 keys to adjust the receiver (max.) audio output level:

-PL 0 500 mV

-PL 1 300 mV

-PL 2 150 mV

Press the MEM 5 key to store the new setting (or the MENU 4 key to cancel).

Note: this parameter only affects the balanced audio output

DISPLAY DISPLAY

AUTO-SCAN

MANUAL CHANNEL

SELECTION

AUDIO OUTPUT LEVEL

ADJUSTING

9 10

821.325 MHz

42 31

GROUP CHANNEL

PL 1

821.325 MHz

ENGLISH

MUTE FUNCTION

Press the MENU 4 key 4 times (sequentially): the display indicates the mute function

(the note in the centre is now ﬂashing).

Use the UP 2 / DOWN 3 keys to turn the mute function on / off and then press the

MEM 5 key to store the new setting (or the MENU 4 key to cancel).

If the mute function is on, the receiver audio output will be disabled.

Note: if the transmitter is muted, no audio signal will be sent out from the receiver!

SQUELCH CONTROL

The squelch can be useful to reduce audible noise during pauses, by muting the receiver

every time the audio level drops below a deﬁned threshold, which is set through the

squelch control.

A higher value means a higher squelch threshold.

Use the squelch control with care: if its threshold is too high, the squelch could also mute

quiet audio signals. A too high squelch threshold also decreases the usable range.

Press the MENU 4 key 5 times (sequentially): the display indicates 'Si' and a value.

Use the UP 2 / DOWN 3 keys to adjust the receiver squelch threshold:

Press the MEM 5 key to store the new setting (or the MENU 4 key to cancel).

VALUE

SQUELCH THRESHOLD LEVEL

- 95.0 dB

- 91.7 dB

- 88.3 dB

- 85.0 dB

- 81.7 dB

- 78.3 dB

- 75.0 dB

- 71.7 dB

- 68.3 dB

- 65.0 dB

SQUELCH CONTROL

MUTE FUNCTION

821.325 MHz

MUTE FUNCTION: OFF MUTE FUNCTION: ON

821.325 MHz

ENGLISH

Remove (unscrew) the microphone handle to access the battery compartment 5.

1 MIC. CAPSULE GRILLE

Extremely rugged spring steel mesh grille to protect the capsule underneath in live

performances.

2 LCD DISPLAY

See the ‘TX 4000 / PX 4100 transmitter operation’ manual section for detailed

information.

3 CH/ON key

Press and hold (for a few seconds) this key to turn the transmitter on / off.

When the transmitter is switched on, press once or more times to select the parameter to

edit:

- C H. channel selection

- G P. group selection

- P L. RF power level

- Unlock / Lock

Press once or more time the SELECT key 4 to change values.

After a few seconds since the last setting, the display will show the current selected

frequency [MHz] and the battery life.

4 SELECT key

Press once or more time to change values when editing parameters.

Press and hold (for a few seconds) to mute / unmute the microphone.

5 BATTERY COMPARTMENT

Use 2 non-rechargeable ‘AA’ type (1.5 V) batteries, better if alkaline and new.

Pay attention to the polarity when inserting the 2 batteries.

6 ANTENNA

The antenna is integrated in the transmitter, under the coloured plastic cap (that is

available in 7 different colours for easy identiﬁcation).

TX 4000 TRANSMITTER / HANDHELD

DYNAMIC MICROPHONE

124

ENGLISH

1 LCD DISPLAY

See the 'TX 4000 / PX 4100 transmitter operation' manual section for detailed

information.

2 CH/ON key

Press and hold (for a few seconds) this key to turn the transmitter on / off.

When the transmitter is switched on, press once or more times to select the parameter to

edit:

- C H. channel selection

- G P. group selection

- P L. RF power level

- Unlock / Lock

Press once or more time the SELECT key 3 to change values.

After a few seconds since the last setting, the display will show the current selected

frequency [MHz] and the battery life.

3 SELECT key

Press once or more time to change values when editing parameters.

Press and hold (for a few seconds) to mute / unmute the transmitter.

4 INPUT (mini 4P connector)

Input for the LA 2004 'Lavalier' (tie-clip) electret microphone.

1. ground

2. power supply for electret microphones

3. audio signal input for an electric guitar / bass

(a cable with jack - mini 4p connectors is needed, NOT included in RCF kits)

4. audio signal input for a microphone

5 BATTERY COMPARTMENT

Use 2 non-rechargeable ‘AA’ type (1.5 V) batteries, better if alkaline and new.

Pay attention to the polarity when inserting the 2 batteries.

6 BELT CLIP

7 FLEXIBLE ANTENNA

note: avoid covering the antenna with hands, clothes, etc.

143

PX 4100 BODY PACK TRANSMITTER

ENGLISH

TX 4000 / PX 4100

TRANSMITTER OPERATION

IMPORTANT INFORMATION

-When more wireless devices are used at the same time, each transmitter / receiver

pair shall be set to its own channel that must be different from all already used.

A channel (frequency) can be used for 1 transmitter only (2 or more transmitters

cannot be set to the same channel).

-It is possible to use up to 16 channels simultaneously.

For instance, the following 10 channels can be used simultaneously without any

interference:

-group 1, channel 1 798.125 MHz

-group 2, channel 1 798.325 MHz

-group 2, channel 2 800.725 MHz

-group 2, channel 5 807.925 MHz

-group 3, channel 4 805.725 MHz

-group 5, channel 1 798.125 MHz

-group 5, channel 8 815.725 MHz

-group 7, channel 1 799.325 MHz

-group 8, channel 6 811.525 MHz

-group 12, channel 2 802.725 MHz

-In case of interferences due to lighting equipments, computers, other radio transmitters,

etc. nearby, it is advisable to try different frequencies.

-Wireless microphones should be used in an open-space with no obstacles (especially

metallic objects) between transmitters and receivers.

-For the best performances, always use 2 new non-rechargeable alkaline ‘AA’ TYPE

batteries and keep transmitters as close as possible to receivers.

Press and hold (for a few seconds) the CH/ON key 2 to turn the transmitter on.

The current selected frequency [MHz] and the battery life are displayed.

OPERATION

When the transmitter is switched on, press once or more times the CH/ON key 2 to

select the parameter to edit:

- C H. channel selection

-G P. group selection

- P L. RF power level

- Unlock / Lock (setting protection)

Press once or more time the SELECT key 3 to change values.

the select key

cannot change channels, groups and rf power if the ‘unlock / lock’

parameter is set to ‘lock’.

After a few seconds since the last setting, the display will show the current selected

frequency and the battery life again.

IMPORTANT INFORMATION

OPERATION

798. 125

MHz

ENGLISH

CHANNEL SELECTION

The frequency range is in the UHF band (798 MHz ÷ 827 MHz).

Before setting a different channel, please see the table (groups, channels and respective

frequencies) in the 'Frequency' manual section.

For instance, to select the frequency preset of 821.325 MHz (group 9, channel 10), please

follow the following procedure:

-Turn the transmitter on ﬁrst.

-Press CH/ON key 2 once to edit the channel parameter, then press once or more times

the SELECT key 3 to specify the proper channel (example: no. 10).

-Press the CH/ON key 2 once again to edit the group parameter, then press once or

more times the SELECT key 3 to specify the proper group (example: no. 9).

After a few seconds, the last setting will be automatically stored and the display will

show the (new) selected frequency and the battery life again.

RF OUTPUT POWER SELECTION

Press CH/ON key 2 3 times to edit the RF output power, then press once or more time

the SELECT key 3 to change values.

SELECTION

PL 0

PL 1

PL 2

TX 4000 / PX 4100 RF OUTPUT POWER

1 mW

3 mW

10 mW

After a few seconds, the last setting will be automatically stored and the display will

show the selected frequency and the battery life again.

LOCK FUNCTION

Since the CH/ON and SELECT keys may be accidentally pressed, it is possible to protect

the current settings thanks to the 'lock' function.

When the transmitter is set to 'lock', it is still possible to use the CH/ON key to select

parameters, but only the 'Unlock / Lock' can be edited.

Press CH/ON key 2 4 times to edit the 'Unlock / Lock' parameter, then use the SELECT

key 3 to select.

After a few seconds, the last setting will be automatically stored and the display will

show the selected frequency and the battery life again.

CHANNEL SELECTION

C H. 10

G P. 9

P L. 2

LOCK FUNCTION

ENGLISH

MUTE

Press and hold (for a few seconds) the SELECT key 3 to mute the transmitter.

When the transmitter is muted, the audio signal is NOT transmitted (while the carrier

radio signal is still present).

Press and hold the SELECT key 3 again to unmute the transmitter.

Ch. 1

Ch. 2

Ch. 3

Ch. 4

Ch. 5

Ch. 6

Ch. 7

Ch. 8

Ch. 9

Ch.10

Ch.11

Ch.12

Group 1

798.125

800.525

802.925

805.325

807.725

810.125

812.525

814.925

817.325

819.725

822.125

824.525

Group 2

798.325

800.725

803.125

805.525

807.925

810.325

812.725

815.125

817.525

819.925

822.325

824.725

Group 3

798.525

800.925

803.325

805.725

808.125

810.525

812.925

815.325

817.725

820.125

822.525

824.925

Group 4

798.725

801.125

803.525

805.925

808.325

810.725

813.125

815.525

817.925

820.325

822.725

825.125

Group 5

798.925

801.325

803.725

806.125

808.525

810.925

813.325

815.725

818.125

820.525

822.925

825.325

Group 6

799.125

801.525

803.925

806.325

808.725

811.125

813.525

815.925

818.325

820.725

823.125

825.525

Group 7

799.325

801.725

804.125

806.525

808.925

811.325

813.725

816.125

818.525

820.925

823.325

825.725

Group 8

799.525

801.925

804.325

806.725

809.125

811.525

813.925

816.325

818.725

821.125

823.525

825.925

Group 9

799.725

802.125

804.525

806.925

809.325

811.725

814.125

816.525

818.925

821.325

823.725

826.125

Group 10

799.925

802.325

804.725

807.125

809.525

811.925

814.325

816.725

819.125

821.525

823.925

826.325

Group 11

800.125

802.525

804.925

807.325

809.725

812.125

814.525

816.925

819.325

821.725

824.125

826.525

Group 12

800.325

802.725

805.125

807.525

809.925

812.325

814.725

817.125

819.525

821.925

824.325

826.725

The following table shows all available frequencies [MHz] assigned to every

group / channel.

FREQUENCIES

MUTE

ENGLISH

SYSTEM

Channel

Type

Frequency band

Frequency response

Frequency stability

T.H.D.

Modulation mode

Dynamic

RX 4016 RECEIVER

Balanced audio output

Unbalanced audio output

S/N Ratio

RF sensitivity

Power supply

Dimensions

Net weight

TX 4000 TRANSMITTER / HANDHELD MICROPHONE

RF output power

Frequency response

Microphone capsule

Tone frequency

Max. deviation

Batteries

Dimensions

Net weight

PX 4100 BODY PACK TRANSMITTER

RF output power

Frequency response

LA 2004 mic. freq. resp.

Tone frequency

Max. deviation

Batteries

Dimensions

Net weight

Included microphone

single (out of 144 frequencies)

(PLL) UHF, ‘diversity’ receiver

UHF, 798 MHz ÷ 827 MHz

50 Hz ÷ 50 kHz (± 3 dB)

± 0.005 % (–10 ÷ 50°C)

< 0.8% (1 kHz)

FM (F3E)

> 100 dB

1 V, ± 35 kHz deviation

750 mV, ± 35 kHz deviation

> 90 dB

– 100 dBm / 30 dB SINAD

through external 15 V dc (0.5A) adapter

210 mm (w), 44 mm (h), 155 mm (d);

(8.2” x 1.7” x 6.1”)

0.99 kg

1 - 3 - 10 mW

90 Hz ÷ 12 kHz (± 3 dB)

dynamic, cardioid

30-33 kHz

± 35 kHz

2 x ‘AA’ type (1.5 V, non rechargeable)

277 mm (l), Ø 36.5 mm;

(10.9” x Ø 1.44”)

0.25 kg

1 - 3 - 10 mW

50 Hz ÷ 15 kHz (± 3 dB)

100 Hz ÷ 12 kHz (± 3 dB)

30-33 kHz

± 35 kHz

2 x ‘AA’ type (1.5 V, non rechargeable)

97 mm (w), 68 mm (h), 22 mm (d);

(3.82” x 2.68” x 0.87”)

0.01 kg

LA 2004 ‘Lavalier’ (tie-clip) electret

microphone

SPECIFICATIONS

ITALIANO

IMPORTANTE

Prima di collegare ed utilizzare questo prodotto, leggere attentamente le istruzioni

contenute in questo manuale, il quale è da conservare per riferimenti futuri.

Il presente manuale costituisce parte integrante del prodotto e deve accompagnare

quest’ultimo anche nei passaggi di proprietà, per permettere al nuovo proprietario di

conoscere le modalità d’installazione e d’utilizzo e le avvertenze per la sicurezza.

L’installazione e l’utilizzo errati del prodotto esimono la RCF S.p.A. da ogni responsabilità.

ATTENZIONE: Per prevenire i rischi di ﬁamme o scosse elettriche, non esporre mai

questo prodotto alla pioggia o all’umidità.

AVVERTENZE PER LA SICUREZZA

1. Tutte le avvertenze, in particolare quelle relative alla sicurezza, devono essere lette con

particolare attenzione, in quanto contengono importanti informazioni.

2. Alimentare il ricevitore utilizzando solo l’alimentatore dedicato; veriﬁcare che la

tensione della vostra rete corrisponda quella di targa dell’alimentatore e che il valore

ed il tipo (continua o alternata) di tensione d’uscita dello stesso corrisponda a quella

d’ingresso del ricevitore, in caso contrario rivolgersi ad un rivenditore RCF; veriﬁcare

inoltre che l’alimentatore non sia stato danneggiato da eventuali urti o sovraccarichi.

La tensione di rete, alla quale è connesso l’alimentatore, ha un valore sufﬁcientemente

alto da costituire un rischio di folgorazione per le persone: prestare attenzione durante

la connessione alla rete (es. non effettuarla con le mani bagnate) e non aprire mai

l’alimentatore. Accertarsi che il cavo dell’alimentatore non sia o possa essere schiacciato

da altri oggetti (prestando particolare attenzione alla parte del cavo vicino alla spina ed

al punto dove questo esce dall’alimentatore).

3. Impedire che oggetti o liquidi entrino all’interno dei prodotti, perché potrebbero

causare un corto circuito. Tutti gli apparecchi non devono essere esposti a stillicidio o a

spruzzi d’acqua; nessun oggetto pieno di liquido (es. vasi) e nessuna sorgente di ﬁamma

nuda (es. candele accese) deve essere posto sugli apparecchi.

4. Non eseguire sui prodotti interventi / modiﬁche / riparazioni se non quelle

espressamente descritte sul manuale istruzioni.

Contattare centri di assistenza autorizzati o personale altamente qualiﬁcato quando:

-l’apparecchio non funziona (o funziona in modo anomalo);

-l’alimentatore e/o il suo cavo sono danneggiati;

-oggetti o liquidi sono entrati nell’apparecchio;

-l’apparecchio ha subito forti urti.

5. Qualora questo prodotto non sia utilizzato per lunghi periodi, scollegare l’alimentatore

del ricevitore dalla rete elettrica e rimuovere le batterie dal trasmettitore.

6. Nel caso che da un prodotto provengano odori anomali o fumo, spegnerlo

immediatamente, scollegare l’alimentatore del ricevitore dalla rete elettrica e/o rimuovere

le batterie dal trasmettitore.

7. Non collegare a questo prodotto altri apparecchi e accessori non previsti.

Veriﬁcare l’idoneità della superﬁcie sulla quale il ricevitore è posizionato, considerando,

ad esempio, vibrazioni meccaniche normalmente generate da un trasduttore.

Per evitare il pericolo di cadute, non sovrapporre fra loro più ricevitori.

8. La RCF S.p.A. raccomanda vivamente che l’installazione di questo prodotto sia

eseguita solamente da installatori professionali qualiﬁcati (oppure da ditte specializzate)

in grado di farla correttamente e certiﬁcarla in accordo con le normative vigenti. Tutto

IMPORTANTE

ATTENZIONE

AVVERTENZE PER LA SICUREZZA

ITALIANO

il sistema audio dovrà essere in conformità con le norme e le leggi vigenti in materia di

impianti elettrici.

9. Sostegni e Carrelli

Se previsto, il prodotto va utilizzato solo su carrelli o sostegni consigliati dal produttore.

L’insieme apparecchio-sostegno / carrello va mosso con estrema cura. Arresti improvvisi,

spinte eccessive e superﬁci irregolari o inclinate possono provocare il ribaltamento

dell’assieme.

10. Vi sono numerosi fattori meccanici ed elettrici da considerare quando si installa un

sistema audio professionale (oltre a quelli prettamente acustici, come la pressione sonora,

gli angoli di copertura, la risposta in frequenza, ecc.).

11. Perdita dell’udito

L’esposizione ad elevati livelli sonori può provocare la perdita permanente dell’udito.

Il livello di pressione acustica pericolosa per l’udito varia sensibilmente da persona

a persona e dipende dalla durata dell’esposizione. Per evitare un’esposizione

potenzialmente pericolosa ad elevati livelli di pressione acustica, è necessario che

chiunque sia sottoposto a tali livelli utilizzi delle adeguate protezioni; quando si fa

funzionare un trasduttore in grado di produrre elevati livelli sonori è necessario indossare

dei tappi per orecchie o delle cufﬁe protettive.

Consultare i dati tecnici contenuti nei manuali istruzioni per conoscere le massime

pressioni sonore che i diffusori acustici sono in grado di produrre.

12. Per evitare fenomeni di rumorosità indotta sui cavi che trasportano segnali dai

microfoni o di linea (per esempio 0dB), usare solo cavi schermati ed evitare di posarli

nelle vicinanze di:

-apparecchiature che producono campi elettromagnetici di forte intensità;

-cavi della rete elettrica;

-linee che alimentano altoparlanti.

13. Non puntare microfoni verso altoparlanti vicini (in modo da evitare ﬁschi fastidiosi).

14. Collocare il prodotto lontano da fonti di calore e garantire la circolazione dell’aria

intorno.

15. Non forzare mai gli organi di comando (tasti, manopole ecc.).

16. Non usare solventi, alcool, benzina o altre sostanze volatili per la pulitura delle parti

esterne; usare un panno asciutto.

INFORMAZIONI SULLE PILE

1. Usare pile tipo AA (1,5 V) non ricaricabili, meglio se alcaline e possibilmente nuove.

2. Non utilizzare contemporaneamente pile vecchie e nuove.

3. Non utilizzare contemporaneamente tipi diversi di pile.

4. Non tentare di ricaricare pile non ricaricabili.

5. Veriﬁcare che sia rispettata la polarità delle pile, seguendo le indicazioni riportate sul

vano del trasmettitore.

6. Togliere le pile una volta esaurite o nel caso il radiomicrofono non sia utilizzato per un

lungo periodo.

7. Non cortocircuitare le pile (ad esempio collegando i 2 poli opposti con un ﬁlo di

metallo).

8. Smaltire le pile esaurite negli appositi contenitori, facendo riferimento alle norme di

legge vigenti (nel paese di utilizzo) in materia di ecologia e protezione dell’ambiente.

9. Non gettare mai le pile nel fuoco od immergerle nell’acqua.

INFORMAZIONI SULLE PILE

ITALIANO

RCF S.P.A. VI RINGRAZIA PER L’ACQUISTO DI QUESTO PRODOTTO, REALIZZATO

IN MODO DA GARANTIRNE L’AFFIDABILITÀ E PRESTAZIONI ELEVATE.

DESCRIZIONE

TX 4016 e PX 4116 sono radiomicrofoni UHF.

Ciascun ricevitore ha 2 antenne in modo da ottenere la funzione “diversity”

(è automaticamente selezionato il segnale radio con livello più alto ricevuto da una

delle 2 antenne), che comporta una migliore afﬁdabilità e copertura con meno rischi di

interruzioni ed interferenze.

La frequenza portante del trasmettitore può essere ricercata automaticamente grazie alla

funzione “auto-scan” del ricevitore.

È ovviamente possibile scegliere manualmente il canale sia nel trasmettitore sia nel

ricevitore.

Sono disponibili 144 canali (12 gruppi, ciascuno con 12 frequenze diverse).

È possibile utilizzare fino a 16 canali contemporaneamente (avendo a disposizione

16 radiomicrofoni).

Il kit TX 4016 include:

-un ricevitore RX 4016

(con alimentatore AC / DC, 2 antenne ed un cavo da 1,5 m con jack 6,3 mm);

-un trasmettitore ad impugnatura TX 4000 con microfono dinamico.

Il kit PX 4116 include:

-un ricevitore RX 4016

(con alimentatore AC / DC, 2 antenne ed un cavo da 1,5 m con jack 6,3 mm);

-un trasmettitore per cintura PX 4100;

-un microfono ad elettrete di tipo “Lavalier” LA 2004.

CARATTERISTICHE PRINCIPALI

COMUNI

-PLL (“phase-locked loop”: anello ad aggancio di fase), banda UHF.

-Utilizzo simultaneo di max. 16 canali / frequenze (su 144 disponibili).

RICEVITORE RX 4016 CON FUNZIONE “DIVERSITY”

-Interfaccia utente semplice con display LCD frontale.

-Ricerca automatica della frequenza portante del trasmettitore.

-Commutazione automatica dell’antenna ricevente il segnale radio (funzione “diversity”).

-Selezione di 3 livelli d’uscita.

-Controllo “Squelch”.

TRASMETTITORI TX 4000 / PX 4100

-Verniciatura “Soft touch” per un uso più confortevole.

-Selezione di 3 livelli di potenza del segnale radio in uscita.

-Disattivazione del microfono (funzione “Mute”).

-Protezione delle impostazioni da modiﬁche accidentali (funzione “Lock”).

CARATTERISTICHE

PRINCIPALI

La pagina sta caricando ...

RCF TX 4016 Manuale del proprietario

Marca: RCF

Modello: TX 4016

Categoria: Microfoni

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: RCF TX 4016 Owner's manual

RCF TX 4016 Manuale del proprietario

RCF TX 4016 Manuale del proprietario

in altre lingue

Altri documenti