Pottinger RP 3500 LSC Istruzioni per l'uso

Operator's manual

+ INSTRUCTIONS FOR PRODUCT DELIVERY . . . Page 3

Nr. 99 8411.GB.80F.0

Round balers

Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.

GB

ROLLPROFI 3120

(Type 8411 : + . . 01001)

ROLLPROFI 3200

(Type 8412 : + . . 01001)

ROLLPROFI 3500

(Type 8414 : + . . 01001)

ALLG./BA SEITE 2 / 0000-GB

Important information concerning Product

Liability.

According to the laws governing product liability, the manufacturer and dealer are obliged to hand the

operating manual to the customer at the time of sale, and to instruct them in the recommended operating,

safety, and maintenance regulations. Conﬁrmation is necessary to prove that the machine and operating

manual have been handed over accordingly.

For this purpose,

- document A is to be signed and sent to Pöttinger,

- document B remains with the dealer supplying the machine,

- and the customer receives document C.

In accordance with the laws of product liability, every farmer is an entrepreneur.

According to the laws of product liability, property damage is damage caused by a machine and not to

it. An excess of Euro 500 is provided for such a liabilioty.

In accordance with the laws of product liability, entrepreneurial property damages are excluded from

the liability.

Attention! Should the customer resell the machine at a later date, the operating manual must be given

to the new owner who must then be instructed in the recommended regulations referred to herein.

GB Dear Farmer

You have just made an excellent choice. Naturally we are very happy

and wish to congratulate you for having chosen Pöttinger. As your

agricultural partner, we offer you quality and efﬁciency combined with

reliable servicing.

In order to assess the spare-parts demand for our agricultural machines

and to take these demands into consideration when developing new

machines, we would ask you to provide us with some details.

Furthermore, we will also be able to inform you of new developments.

Dokument D

GB-0600 Dokum D Anbaugeräte

PÖTTINGER Landtechnik GmbH

Industriegelände 1

A-4710 Grieskirchen

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

T Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating

devices at hand.

T Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.

T Tyres checked re. correct pressure.

T Wheel nuts checked re. tightness.

T Drive shaft cut to correct lenght.

T *VYYLJ[WV^LY[HRLVɈZWLLKPUKPJH[LK

T Fitting to tractor carried out: to three-point linkage

T Trial run carried out and no defects found.

T Functions explained during trial run.

T Pivoting in transporting and operating position explained.

T Information given re. optional extras.

T Absolute need to read the operating manual indicated.

Please check. X

According to the product liability please check the above mentioned items.

INSTRUCTIONS FOR

PRODUCT DELIVERY

GB

In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.

For this purpose please do the following:

- sign the document A and send it to the company Pöttinger or via the internet to www.poettinger.at

- document B stays with the specialist factory delivering the machine.

- document C stays with the customer.

- 4 -

0500_GB-INHALT_8411

¼ÈÇÍ¾ÇÍÌ

GB

SAFETY INFORMATION

General Safety Instructions .......................................5

General recommendations ........................................5

Hitching the machine to the tractor ...........................5

Machine operation .....................................................6

Road circulation .........................................................8

Handling bales ...........................................................8

Cardan shaft and PTO ...............................................9

Hydraulic system .....................................................10

Servicing the machine .............................................11

Adhesive safety plates .............................................11

Safety plates - location ............................................12

Noise level ...............................................................14

Product clogging removal........................................14

GENERAL INFORMATION

Purpose of the manual ............................................15

Attachments ............................................................15

Warranty ..................................................................15

Machine identification..............................................16

Enclosures ...............................................................16

TECHNICAL INFORMATION

Prescribed use and machine description ................17

Improper use ...........................................................17

Description of the main units ...................................18

Operation description ..............................................19

Technical characteristics .........................................20

Tractor requirements ................................................21

Admissible gradients ...............................................22

Safety devices .........................................................23

Area of danger .........................................................25

Night work ...............................................................25

INSTALLATION INSTRUCTIONS

Packing/ Unpacking ................................................26

Lifting .......................................................................26

Load/ Unload from transportation means ...............27

Hitching to the tractor ..............................................27

Coupling to the towing eye ......................................27

Cardan shaft - Installation .......................................28

Hydraulic system - Connection ...............................28

Electric connection of the automatic binder ............29

Binding Control Unit - Installation ...........................29

Electric connection of the lighting system ...............30

Releasing from the tractor .......................................30

Opening guards .......................................................31

Tests and checks .....................................................31

OPERATION ADJUSTMENTS -

ADJUSTMENTS AND INDICATORS

Bale weight choosing ..............................................32

Pick-up - Balancing .................................................32

Pick-up height - Adjustment ....................................33

Baffle plate - Adjustment .........................................33

Drive change (Mod. 3500) .......................................33

Feed chain - Adjustment .........................................34

Adjustment of hook closure .....................................34

Adjustment of the hook springs ..............................34

Binder control - Adjustments ...................................35

Slide holding chain path and stroke ........................35

Twine shuttle nose adjustment ................................35

OPERATING INSTRUCTIONS

Binding control unit - Instructions for use ...............36

Twine binding instructions .......................................38

Binder start position ................................................38

Twine installation and connection............................38

Twine splicing ..........................................................39

Clamp adjustment ...................................................39

Binding selection .....................................................39

Twine binder operation ............................................41

What to do in case of damage ................................42

Net wrapping instructions .......................................43

Net assembly and connection .................................43

Binder start position ................................................44

Selecting the number of bale wrappings .................45

Reel braking device .................................................45

Roller pressure adjustment ......................................45

Net binder operation ................................................46

Knife resetting tie rod ..............................................46

Adjusting end of stroke blocks and shock

absorbers .................................................................47

Mixed net/ twine binding instructions .....................48

Automatic running ...................................................48

Manual running ........................................................49

What to do in case of failur ......................................49

Product preparation .................................................49

Forward speed diagram ..........................................50

Picking up instructions ............................................51

Floating straw presser plate ....................................52

Bale unloading .........................................................53

Attachments ............................................................54

MAINTENANCE

General maintenance instructions ...........................57

Routine maintenance ...............................................58

Gear box - Lubrication.............................................59

Cardan shaft - Lubrication .......................................59

Drive chains - Adjustment .......................................59

Twine binder - Servicing ..........................................60

Net binder - Servicing ..............................................60

Centralised automatic lubrication ............................60

Lubrication chart ......................................................61

Table of lubricants ...................................................62

End of season checking in a work shop ..................62

TROUBLESHOOTING

Troubles: causes and remedies ...............................64

General troubles ......................................................64

Bale quality ..............................................................65

2-Twine binder .........................................................65

Net binder (Rotomec) ..............................................66

Clarification of “Section” table ................................66

REPAIR AND REPLACEMENTS OF PARTS

Tools ........................................................................67

Pick-up - Safety bolt replacement ...........................67

Ring gear release .....................................................68

Wheel wedges .........................................................69

Replace the feed chain bearings .............................69

SUPPLEMENT

Hydraulic diagram ..................................................70

Electric system ........................................................71

Electric system .......................................................72

Binding modes ........................................................73

Electrical lay-out .....................................................74

Electrical lay-out of Main cabling ............................76

Electrical lay-out of twine binding device cabling ...78

SUPPLEMENT

Recommendations for work safety .........................81

Driveshaft .................................................................82

Lubricants ................................................................ 84

Combination of tractor and mounted implement ....86

- 5 -

0500-GB SICHERHEIT_8411

GB

SAFETY INFORMATION

General Safety Instructions

It is of the utmost importance to comply with work safety

regulations issued by the competent authorities of each

country. The following precautions concerning the machine

operation must be duly observed.

General recommendations

Read carefully this manual before starting,

operating and servicing the machine.

• Read carefully safety decals stuck to the machine and

follow the instructions (see paragraph "ADHESIVE

SAFETY PLATES"). Should decals be damaged or

illegible, immediately replace them, applying to SPARE

PARTS DEPARTMENT.

• Before running the machine, the operator must be

informed about and trained to the machine use.

• Do not operate the machine if wearing clothes which

might entangle into running parts.

• Start working only if the machine is in perfect

conditions.

• Check the conditions of the various components

of the pick-up to ensure proper feed and prevent

jammings.

• Do not use the machine to pick up unsuitable products

and in case of bad weather conditions.

• To prevent rotation, the cardan shaft guard must always

be in perfect working order and fastened through the

relevant chains. Read carefully all instructions provided

by the manufacturer.

• Guards must always be in perfect working order.

• Before resuming work, make sure that all guards have

been properly fitted.

• Always keep a first aid kit within reach.

• A fire extinguisher should also be kept within reach.

Hitching the machine to the tractor

• Before hitching the machine to the tractor, make sure

that the latter is in good working order and that brakes

work correctly, particularly if the machine is to be used

on gradients.

• Furthermore, make sure that the hydraulic system of

the tractor suits the machine system.

• To avoid accidents or damages to the machine, make

sure that the cardan shaft is properly connected both

to the machine and to the tractor.

• Make sure that the tractor drawbar coupling pin is

locked, to prevent it from releasing.

• Make sure that the electric system and turn indicators

work properly.

- 6 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Machine operation

• Before starting the machine, make sure that all safety

guards are in perfect working order and correctly

fitted.

• Only the driver must operate the tractor; no passengers

are allowed on the baler.

• The baler can be operated from the driver’s seat

only.

• Do not walk or stand on the baler drawbar or on other

parts while it is running or when the PTO is engaged.

• Keep far from the pick-up area, belts and rollers of the

machine as well as from binding and running parts.

• People are not allowed to approach the machine during

running and in particular they must not stand in the rear

part of the machine during bale unloading phases.

• Do not stand between the tractor wheels and the

machine when the engine is on.

• Always remove the tractor ignition key and engage the

handbrake when the tractor is unattended.

• Before cleaning, greasing or adjusting the machine or

the PTO, stop the latter, stop the engine, remove the

ignition key and engage the parking brake.

In case of clogging, do not release the baler

while running and unload the bale.

Stop the PTO and the tractor engine before

cleaning the pick-up.

Do not remove from or introduce products

into the pick-up with hands or feet while

the baler is running.

Unload the bale.

- 7 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

In case of product clogging removal, do the

following:

- do not approach the pick-up when it is running;

- disengage the power take-off;

- stop the tractor;

- use a tool to remove the product clogged;

- if need be, open the tail gate and unload the bale

before cleaning the pick-up.

• Before opening the tail gate, make sure that the area

behind the baler is clear.

• Should the machine be operated with the tail gate

open, fit safety catches on both hydraulic jacks.

• Do not leave the baler unattended when the tail gate

is open.

• Do not leave the machine unattended when the tractor

is running.

• Never open gates or guards while the tractor is

running.

• Do not stand on the upper guard of the pick-up or on

running boards while the machine is running.

• Do not use controls or hoses as grips.

• Beware of curves and overturning on bumping soils

and steep gradients.

• Give the greatest attention when wheels are nearby

ditches or steep banks.

• To avoid exposure to dust and soil caused by picked-up

products, always wear glasses and mask when working

with tractors not supplied with cab.

• Always keep the machine in perfect working order and

perform routine maintenance periodically.

WARNING:

whoever stands

in the machine

working range is

in a dangerous

area, being

therefore an

„exposed

person“.

The operator must

prevent people

from standing in

dangerous areas

and must give the

greatest attention

when operating

the machine.

WARNING:

make sure that

there are no

children; make

sure they do

not approach

the machine

and the tractor.

Give a particular

attention

during reverse

- 8 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Road circulation

• During road transport, follow the regulations in force

and drive tractors with adequate towable weight only

(see the registration certificate of the tractor).

• Do not use the machine as a transportation means.

DANGER - WARNING: a wrong assembly

of tyres on rims and an inflation pressure

differing from the values shown by the table

"TRACTOR REQUIREMENTS", might cause

dangerous accidents, particularly during

road transportation. Apply to specialised

workshop, should a check be necessary.

• During road circulation, the cardan shaft must be

connected to the tractor PTO.

• Before towing the machine on the road, raise the pick-up

completely and close the valve on the hydraulic hose

(see paragraph installation "HYDRAULIC SYSTEM-

CONNECTION").

• Hook the pick-up to the chain supplied.

• Do not exceed the maximum speed permitted by the

highway code and, in any case, never exceed the speed

of 40 km/h or 25 mph.

• Periodically check the working order of the lighting and

signalling systems.

• The operator must always be aware of the machine

dimensions during manoeuvres.

Handling bales

• Give the greatest attention to the weight and barycenter

of the lifted bale if using front loaders.

• For covering short distances, bales can be transported

by equipping the tractor with front or rear fork, whereas

for greater distances normal or special trucks must be

used.

Keep to the current legislation during transport on

public roads.

• Never unload or store bales along gradients, since

bales might roll down.

• Make sure that bales are correctly fastened through

ropes or other suitable means.

DANGER OF FIRE: straw is highly

inflammable, it might cause fire. In case of

fire, immediately unload the bale and move

the machine away. If necessary, disconnect

the machine from the tractor.

• Fire risks can be avoided by keeping the machine

clean.

• It is advisable to keep a fire extinguisher within

reach.

- 9 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Cardan shaft and PTO

• The power take off of the tractor must turn at the speed

recommended by the manufacturer.

• The cardan shaft must be manufactured in compliance

with EN1152 standards and provided with CE

certificate.

• The cardan shaft must be supplied with guards.

• Make sure not to damage the cardan shaft guard during

transport or working cycle.

• All guards must be in good conditions.

• * Before cardan shaft is installed onto or taken off the

p.t.o., the p.t.o. must be switched off, the motor turned

off and ignition key removed

• The safety joint must be installed on the side of the

baler. The homocinetic joint joint must be installed on

the tractor side.

• Make sure that all rotating parts connected to the PTO

shaft are properly protected.

• In order to prevent crawling, assemble the cardan

shaft supplied with the machine between the tractor

PTO and the machine gear box, making sure that the

length does not exceed the min. distance between

the machine and the tractor. Should the cardan shaft

be shortened, cut both pipes and the relevant guards,

removing burs and greasing ends.

The shaft length must ensure a sufficient

overlap of the telescopic shafts; the tractor

must be perfectly aligned with the machine

and keep a minimum overlap of half.

• Ensure that all turning parts connected to the p.t.o.

cardan shaft are properly safeguarded

• Connect chains to prevent any protection devices from

rotating

• Before engaging the PTO, make sure that the selected

tractor PTO speed and the rotation direction match

with the baler rotation and speed values.

• Before engaging the PTO, make sure that nobody stands

in the baler working area or in dangerous areas.

• Never engage the PTO with the engine stopped.

• Make sure that nobody approaches the cardan shaft

during running.

• Disengage the PTO before sharp curves or when it is

not necessary.

• Before any operation, make sure that the machine and

the tractor engine are stopped and remove the ignition

key.

• Before cleaning, greasing or adjusting the machine

or the PTO, disengage the latter, stop the engine and

remove the ignition key.

• The cardan shaft, once disconnected from the tractor,

must be placed on the support at the drawbar end.

WARNING

• Keep to the

instructions of

the cardan shaft

operation manual.

WARNING:

should running

parts rotate after

the PTO has been

disengaged, keep

far from rotating

parts.

- 10 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Hydraulic system

• Before connecting or disconnecting the hydraulic

system pipes of the tractor, release pressure from the

tractor and machine systems.

• Give the greatest attention to hydraulic coupling

between the tractor and the machine: it is advisable to

mark male and female couplings to avoid manoeuvre

errors. Should hydraulic couplings be changed,

some functions might accordingly be changed (ex.

lift/lowering).

Danger of accidents!

• Periodically check hydraulic pipes and replace them

when damaged or worn-out. Replacing pipes must

have the same technical specifications as the original

pipes. Hoses must however be replaced after 5 years

from the date printed on the hose.

• When detecting leaks, use suitable protections.

Danger of accidents!

• The hydraulic pressurised oil might penetrate the skin,

thus causing serious damages. In such a case, consult

a doctor immediately.

Danger of serious infections!

• Before servicing the hydraulic system, lower the baler

tail gate, the pick up, release pressure and stop the

tractor engine.

• To prevent hydraulic couplings from getting dirty or

damaged, always fit the protection caps supplied after

use.

WARNING:

the hydraulic

system works

at high pressure

(min 100 bar /

max 190 bar).

CAUTION:

do not dispose of

hydraulic oil in the

environment.

- 11 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Servicing the machine

• Replace as soon as possible all worn or damaged parts

of the pick-up to prevent frequent jammings.

• Comply with scheduled maintenance intervals. From

time to time the machine requires minor servicing.

It should be reminded that a correct and regular

maintenance will increase the working life of the

machine.

• Always replace the belts when these are worn or

damaged.

• Before carrying out any operation over or under the

machine, make sure to insert wedges under wheels.

• When servicing the hydraulic system, make sure that

the system is not pressurised before disconnecting

any pipe.

• Leaks of pressurised oil might cause serious injuries.

When searching for oil leaks always wear protective

clothes, goggles and gloves.

• Before welding machine parts or before servicing the

electric system, release the baler from the tractor, to

protect the alternator and the battery of the latter.

• To avoid fire risks, always keep the machine clean.

• Belts and rollers must be cleaned at least once a day

or whenever used.

• Tyres must be serviced by skilled personnel and through

appropriate tools. A wrong assembly might cause

serious injuries or death. In case of doubts, apply to

qualified personnel.

• To avoid damages to mechanical parts, do not use

pressurised water jets to clean the machine.

Adhesive safety plates

It is of the utmost importance to give the greatest attention

to adhesive warning and/or precautions plates fitted on

the machine, when starting, repairing or simply standing

nearby it.

The user shall keep all plates legible, changing their location

should they fail to be seen and replacing them when

damaged. Damaged plates must be replaced by ordering

a complete set to SPARE PARTS DEPARTMENT.

- 12 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Safety plates - location

1 - General danger!

Read the manual before operating the

machine.

(Code 8889379)

2 - No standing!

Do not stand within the working range

of the machine.

(Code 8889286)

3 - General danger!

Stop the tractor and remove the ignition

key before servicing the machine.

(Code 8889378)

4 - Danger of body crushing!

Fasten the lifting jack through the locking

device before accessing the dangerous

area.

(Code 8889380)

5 - Danger of chest crushing!

Keep far from the baler tail gate while the

tractor engine is running.

(Code 8889381)

6 - Danger of arm entangling!

Do not approach the pick up area with

hands or feet while the tractor engine

is running.

(Code 8889390)

7 - Danger of chest crushing!

Bale out of control.

(Code 8889383)

8 - Danger of chest crushing!

Tail gate is closing.

(Code 8889382)

9 - Danger of arm entangling!

Do not open and remove safety guards

while the engine is running.

- 13 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

10 - Danger of arm entangling!

Do not open and remove safety guards

while the engine is running.

(Code 8889384)

11 - Danger of arm entangling!

Do not introduce hands into the auger while

the engine is running.

(Code 8889389)

12 - Danger of finger or hand cutting!

Do not approach the knife cutting area with

hands. Do not open and remove safety

guards while the engine is running.

(Code 8889377)

13 - Danger of chest crushing!

Keep far from the baler drawbar range while

the tractor engine is running.

(Code 8889394)

14 - Danger of chest crushing!

Keep far from the tractor range while the

engine is running.

(Code 8889393)

15 - Danger of contact with hydraulic

fluids!

Pressurised fluid leaks might penetrate the

skin causing serious injuries.Disconnect

the machine and stop the tractor before

servicing.

(Code 8889969)

16 - Danger of leg cutting or crushing!

Keep far from the machine range.

(Code 8889970)

17 - Danger of electric shock!

Give the greatest attention when operating

the machine nearby electric cables.

(Code 8889968)

18 - Safety devices!

(Code 8889726)

19 - Danger!

Wheels in transport position - before using

the machine turn around the wheels!

- 14 -

0500-GB SICHERHEIT_8411

SAFETY INFORMATION GB

Noise level

According to 86/188 EEC standards and to the current

national law, the following noise levels, detected during

work and measured in dBa, in accordance with ISO 5131

regulation should not be exceeded.

Noise level is measured with the engine and all systems

working, at a normal running speed, according to the

specific use, without product fed into the machine.

To measure the noise level of the tractor-machine unit, the

noise of the baler trailed by the tractor is measured at a

distance of 200 m from the rear window of a cabsupplied

tractor, suitable for trailing the baler.

As far as cab-supplied tractors are concerned, the noise

heard by the operator, keeping doors and windows closed,

will be less, depending on the cab acoustic insulation.

If the tractor is not supplied with cab or works with open

doors and windows, the noise level will exceed 85(dBa),

therefore it is advisable to wear protective headphones.

Since said regulation is in force in many countries, the

operator shall comply with the local current law.

Product clogging removal

DANGER - WARNING: In case of product

clogging removal, do the following:

- do not approach the pick-up when it is running;

- disengage the power take-off;

- stop the tractor;

- use a tool to remove the product clogged; if need be,

open the tail gate and unload the bale before cleaning

the pick-up.

CAUTION: Before starting work always

check the conditions of the components

of the pick up (tines, bars, bushes, cam,

clamps).

GB

GENERAL INFORMATION

- 15 -

0200-GB ALLGEMEINE INFO (8412)

Read this manual carefully before servicing

the machine. This manual must be perfectly

kept inside the plastic bag and put inside

the twine case.

Purpose of the manual

This manual has been drafted by the manufacturer and is

integral part of the machine (1).

Information contained herein is aimed at qualified and

skilled personnel (2) (operators).

Dealers of new or second-hand machines must provide

this manual, previously supplied with the machine.Should

the machine be sold, the purchaser must be supplied with

the operation and maintenance manual.

Should this manual be damaged or lost, order another

to SPARE PARTS DEPARTMENT, specifying its number,

or if missing, all data printed on the rating plate fitted to

the machine.

The manual defines the purpose for which the machine has

been manufactured as well as all information necessary

to ensure a safe and correct operation.

The compliance with the instructions contained herein

ensures both the operator’s and machine safety, running

economy and prolong the working life of the machine.

Particularly important paragraphs have been highlighted

in bold characters and preceded by the following

symbols.

WARNING: shows imwhich might cause

injuries, give it the greatest attention.

CAUTION: shows that it is necessary to

give particular attention to avoid accidents

or damages to things.

Shows particularly important technical

Pictures and figures are merely supplied as examples.

Should the machine owned differ from figures shown in

this manual, safety information is however ensured.

Some figures show the machine with open or removed

guards, to make features and adjustments clearer.

Never operate the machine under these

conditions.

For safety purposes, make sure that all safety guards are

closed or correctly fitted before starting the machine.

In pursuing a policy of constant development and updating

of the product, the manufacturer might introduce changes

or improvements to the machine whenever he deems it

possible, without introducing said changes to the machines

previously sold.

(1) The machine definition replaces the trade definition, object of this

manual (see the cover).

(2) Operators who have acquired a specific experience, technical skill and

knowledge of the current law, who are able to operate the machine and

avoid any danger when handling, installing, operating and servicing

the machine.

Attachments

The machine has been designed to work under different

conditions and products. However, additional attachments

might be required to improve the performance.

A list of optional attachments is shown in the chapter

”Attachments” of this manual.

Warranty

The machine is in compliance with the law in force in the

user’s country and the conditions agreed with the dealer.

The warranty shall be void should the machine be damaged

or changed, disregarding the instructions set forth in the

operation manual.

- 16 -

0500-GB ALLGEMEINE INFO_8411

GENERAL INFORMATION GB

Machine identification

The model is identified by the rating plate showing the

following data:

A - Commercial name of the machine

B - Serial number

C - Year of construction

D - Type of approval (in force in Italy)

E - Number of road approval (in force in Italy)

F - Max. PTO rpm

G - Total max. mass

H - Total max. mass on towing eye

L - Max. mass on axle

M - Manufacturer

Always indicate A - B - C when requesting

information, spare parts, etc.

Always use original spare parts if necessary.

Using non original spares or performing unauthorised

operations on the machine will void the warranty.

Enclosures

- EC Conformity Declaration

- Type approval certificate.

- Conformity declaration for type-approved vehicles

(Italy only).

These documents are to be kept safe and protected from

the weather for the entire life of the machine.

- 17 -

0200-GB TECHNISCHE INFO_8411

GB

TECHNICAL INFORMATION

Prescribed use and machine description

This machine is a pick-up baler, designed exclusively to

collect windrows of straw, hay and similar products, and

press such products into cylindrical bales.

This is a trailed machine and requires a suitable tractor unit

for pulling and powering the transmission drive.

The machine picks up and bales fodder, including mixed

gramineae and lucerne, for agricultural use on lands

under crop.

All picking up, binding and unloading operations are

controlled by the operator from the tractor cab.

This machine can be used to harvest different crops:

graminaceous crops, straw, hay, maize stalks, ensiled

produce, thanks to its combination of rollers and

chains.

The machine can be equipped with a wide pick-up, with

large-diameter side augers, for wide and bulky windrow

harvesting. The bale can be twine bound, net wrapped

or mixed bound.

As soon as binding is over, the bale is unloaded by opening

the tail gate.

The machine has been manufacturer to be used by a single

operator (tractor driver).

Comply with the accident prevention regulations in force

in the user’s country.

Use original spare parts only.

Improper use

• The machine cannot be used as a transport means for

people or things.

• Do not allow people to remain on the service running

board while the machine is running.

Always stop the power take off.

• Do not change, remove or assemble parts to the

machine. The manufacturer shall not be liable for

damages thus caused.

• Do not exceed the speed of 40 Km/h.

• The manufacturer shall not be liable for damages caused

by non-original spare parts and attachments.

- 18 -

0200-GB TECHNISCHE INFO_8411

TECHNICAL INFORMATION GB

Description of the main units

The ”Pöttinger” 3000 series is a versatile line: any standard machine can be completed by requesting optional assemblies

in order to meet any possible user’s requirements.

A - Cardan shaft transmission

(see enclosed literature).

B - Drawbar for coupling to tractor

C - Parking jack.

D - Gearbox.

E - Chain drive.

F - Feeding/pressure rollers.

G - Feed chain.

H - Baling chamber.

I - Standard/wide pick-up.

K - Bearing for Cardan shaft in rest position.

L - Wheels.

M - Pick-up wheel.

N - Feed baffle.

P - Floating straw-presser.

Q - Two-twine tying unit (Autolife).

R - Net tying unit (Rotomec).

S - Rear gate.

T - Gate opening hydraulic cylinders.

U - Bale kicker (OPT).

V - Tying unit remote control.

Y - Electric lighting system (OPT).

Z - Main pinion

- 19 -

0200-GB TECHNISCHE INFO_8411

TECHNICAL INFORMATION GB

Operation description

- All machine functions are directly controlled and

supervised from the tractor driver’s cab.

- The machine will move on along the windrow to allow

the crop to be harvested by the pick-up; the crop is

then fed to the baling chamber by the feeding rollers.

- The baffle will help product feeding to the chamber.

- The product is pressed into round bales inside the

chamber; when the required bale pressure is reached,

a sound signal will inform the operator that the tractor

should be stopped.

- The twine or net tying unit will begin automatic or

manual bale tying.

- A sound signal is operated when tying is completed.

- If the machine is not equipped with bale kickers, about

2 - 3 meters in reverse are necessary before the gate

can be opened.

- The operator should now opening the gate to allow

bale unloading on the ground.

- Move ahead of 2 to 3 metres.

- The gate is then fully closed again and the machine is

ready for another cycle.

- 20 -

0200-GB TECHNISCHE INFO_8411

TECHNICAL INFORMATION GB

Technical characteristics

3120 - 3200 3120L - 3200L 3150 - 3500 3150L - 3500L

Feeding

Chamber section mm ø 1200x1200 ø1200x1200 ø1500x1200 ø1500x1200

Pick-up

Pick-up width mm 1200 1680 1200 1680

Tines for row/ tines rows n 20/4 28/4 20/4 28/4

Distance between tines mm 60 60 60 60

Weights

Machine weight kg 2200 2320 2430 2550

Bale

Haybale weight kg 250/320 250/320 390/500 390/500

Straw bale weight kg 170/220 170/220 260/340 260/340

Silage bale weight kg 400/700 400/700 620/1000 620/1000

Bales hourly output n 15/30 18/35 15/30 18/35

Tyres

Tyre 10.0/75-15 10.0/75-15 10.0/75-15 10.0/75-15

Tyre pressure bar 3,7 3,7 3,7 3,7

Wheel for pick-up 16x6.50-8 6PR 16x6.50-8 6PR 16x6.50-8 6PR 16x6.50-8 6PR

Wheel pressure bar 2,5 2,5 2,5 2,5

Twine/Netting

Twine m/kg 500/800 500/800 500/800 500/800

strong mesh net gr/m 14/18 14/18 14/18 14/18

La pagina sta caricando ...

Pottinger RP 3500 LSC Istruzioni per l'uso

Questo manuale è adatto anche per

Pottinger RP 3500 LSC Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti