INTEK M-60 PLUS Manuale del proprietario

Marca: INTEK

Modello: M-60 PLUS

Categoria: Microfoni

Tipo: Manuale del proprietario

MULTI STANDARD PROGRAMMABLE

27 MHz CB MOBILE TRANSCEIVER

M-60 PLUS

OWNER'S MANUAL

MANUALE DI ISTRUZIONI

SAFE DRIVE RADIO !

KEEP YOUR HANDS ON THE STEERING

WHEEL WHILE DRIVING !

0678

NOTICE !

It is recommended to carefully read this owner’s manual before using the product. This will also help the user to

prevent using the radio in violation of the regulations valid in the country where the product is used, as well as to

avoid any possible interferences with other services.

Declaration of Conformity

With the present declaration, we certify that the following products :

INTEK M-60 PLUS

comply with all the technical regulations applicable to the above mentioned products

in accordance with the EC Directives 2006/95/EC, 2004/108/EC, 99/5/EC.

Type of product : CB Transceiver

Details of applied standards : EN 300 433-1/-2, EN 300 135-1/-2

EN 301 489-1, EN 301 489-13

EN 60065

Manufacturer : INTEK S.R.L.

Via G. Marconi, 16

20090 Segrate, Italy

Tel. 39-02-26950451 / Fax. 39-02-26952185

E-mail : [email protected]

Notified Body : EMCCert Dr. Rasek

Boelwiese 5, 91320 Ebermannstadt

Germany

Identification Number : 0678

Contact Reference : Armando Zanni

Tel. 39-02-26950451 / Fax. 39-02-26952185

E-mail : [email protected]

Segrate, 24/02/2012 dr. Vittorio Zanetti

(General Manager)

DECLARATION OF CONFORMITY

EC Certificate of Conformity

(to EC Directive 2006/95, 2004/108, 99/5)

RoHS

2002/95/EC

Index - Introduction

- 1 -

Index - Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Unpacking and checking parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Controls, Indicators and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Frequency bands table - User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Frequency band selection / programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Table of restrictions on the use of CB transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table of restrictions on the use of CB transceivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I

PCB - Main Board & Front Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II-III

Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IV-V

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VI-VII

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VIII-IX

NOTICE !

Before using this transceiver, please check that the radio has been programmed on the frequency bands,

specifications and operating modes allowed by the regulations valid in the country where the product is used. If

not, please proceed to modify the frequency band programming, as it is described in this owner’s manual. This

transceiver is factory pre-programmed on the CE European frequency band (CEPT 40CH FM 4W).

Congratulations!

Congratulations for selecting and purchasing an INTEK quality product. This transceiver includes a number of advanced

functions and systems, therefore it is definitely necessary to carefully read this owner’s manual before using the radio.

With a correct use of the product in accordance with the operating method described in this manual, the product will offer

a trouble free use for many years. INTEK is constantly engaged to develop and provide quality products meeting the

customers requirements, however any suggestion or comment on this product that might help us to improve quality are

warmly welcome. INTEK M-60 PLUS is a CB transceiver using advanced hardware and software design, it includes a

special multi-standard programmable circuit, which allows to program the specifications of the radio (frequency

bands, operating modes, transmitter power) in compliance with the regulations valid in the various European

countries. Therefore this product can be used in any country of the European Community. The radio is delivered

factory pre-programmed on the CE European frequency band (CEPT 40CH FM 4W).

English

Unpacking and Checking Parts - Supplied Accessories

- 2 -

Unpacking and checking parts

Carefully unpack the product. Please identify all the parts listed below, before wasting the packaging. If any part is

missing or if the packaging shows any damage, please contact your dealer immediately.

Supplied accessories

DC power cord with fuse holder and fuse, integrated with the transceiver

Standard microphone with 4-pin connector

Car mounting bracket

Car mounting bracket accessories (hardware, knobs, etc.)

Microphone bracket

Owner’s manual

Microphone bracket Car mounting bracket Owner's manual

Hardware

DC power cord with fuse holder and

fuse, integrated with the transceiver

Standard microphone

English

- 3 -

Controls, Indicators and operation

FRONT PANEL

1. A/F Key

This key allows to select the AM or FM operating mode, in both TX and RX. The AM/FM operating mode selection is

possible only if it if allowed by the programmed frequency band, otherwise the AM/FM selection is not possible.

2. ANL Key

Press the ANL key (3) to enable the ANL (Automatic Noise Limiter) function, in order to reduce electric or

electromagnetic noise or interference on the used channel. The ANL icon (D) is lighted to confirm that the ANL

function is enabled. Press again the ANL key (2) to disable the function.

3. EMG key (Emergency Channels)

This key allows quick access to one of the two pre-programmed emergency channels (CH9 or CH19). Each time this

key is pressed, radio will select CH9, then CH19, then again the normal operating channel.

4. BUSY Indicator. This green color LED indicator is lighted when radio is receiving one communication and the

squelch is open (radio is not in the automatic mute mode).

5. LCD Display

Large size LCD display with blue color backlight function for best readability in darkness. It indicates the operating

channel number, the operating mode, all the programmed settings and all the enabled functions.

1 2 3 4 5 6

7911 812 10

English

- 4 -

Controls, Indicators and operation

A. AM Icon

The AM icon (A) is lighted when radio has is set to the AM (Amplitude Modulation) operating mode.

B. Channel Number

It indicates the operating channel number or the frequency band ID code.

C. S/RF Digital Meter

The digital 5-bar S/RF METER (C) indicates the strength of the received signal (from S0 to S9+30) in the receive mode

and the transmitter RF output power (0 to 4W) in the transmit mode.

D. ANL Icon. The ANL Icon (D) is lighted when the ANL (Automatic Noise Limiter) is enabled.

E. ATT Icon. Not available on this model.

F. H Icon

The H Icon (F) is lighted when the transmitter is in HIGH POWER mode (4W).

G. L Icon

The L Icon (G) is lighted when the transmitter is in LOW POWER mode (1W).

H. FM Icon

The FM icon (H) is lighted when radio is set to the FM (Frequency Modulation) operating mode.

LCD DISPLAY

English

- 5 -

6. Up Key. Press to select the operating channel upward. By keeping a key pressed, the quick channel selection

mode will be enabled.

7. Down Key. Press to select the operating channel downward. By keeping a key pressed, the quick channel

selection mode will be enabled.

8. REMOTE PTT Jack

Connect here the optional Remote PTT Control (RPT-1). Refer to the section “TRANSMITTING MODES” at page 8.

9. AS/SQL Control

SQUELCH CONTROL (SQUELCH manual adjustment)

The SQUELCH control allows to silent the receiver by cutting the background noise, when no signals are received. Turn

the knob clockwise until the background noise is cut. Turn the knob counter clockwise (SQUELCH opening) in order to

listen to the weakest signals.

AS CONTROL (SQUELCH fixed setting)

The AS function allows to automatically silent the receiver, avoding the SQUELCH manual adjustment. A fixed

SQUELCH threshold is factory pre-set. To enable the fixed SQUELCH function, turn the knob fully counter clockwise to

the AS position, until a click noise is heard.

10. OFF/VOL Control

Use this knob to switch radio ON and OFF, as well as to adjust the receiver volume to the desired level. To adjust the

receiver volume in case no signals are received on the operating channel, open the SQUELCH and then adjust the

receiver volume using the background noise as a reference.

11. EXT MIC Jack

Connect here the optional external microphone ESM-444. Refer to the sections “TRANSMITTING MODES” at page 8.

12. Microphone Connector

Connect the standard 4-pin microphone to this connector and turn the connector ring to lock it.

Controls, Indicators and operation

English

IMPORTANT !

Do never attempt to open the cabinet of the transceiver. No user serviceable parts inside. Internal modifications or

tampering may cause damage to the product, modify its technical specifications and will void warranty rights. If

service or repair are required, please go to an authorised service centre or specialized technician.

Controls, Indicators and operation

- 6 -

REAR PANEL

13. EXT (External Speaker) Jack

This jack is for connecting an external speaker (optional).

14. ANTENNA Connector

Antenna connector. Refer to the sections INSTALLATION OF THE ANTENNA.

15. 13.2VDC POWER CORD

13.2VDC power cord input.

English

ANT

EXT

13.2V

1413

- 7 -

Controls, Indicators and operation

MICROPHONE WITH 4-PIN CONNECTOR

English

16. PTT (Push-to-Talk) Key

Transmitter key. Press the PTT key (16) to transmit and release it to

return to the receive mode.

17. MICROPHONE Plug

4-pin microphone connector with locking ring. Connect it to the

microphone connector (12) on the front panel of the radio.

REMOTE PTT CONTROL RPT-1 (OPTIONAL)

18. PTT (Push-to-Talk) Key

Transmitter key. Press the PTT key (18) to transmit and

release it to return to the receive mode.

19. Remote PTT Jack

Connect this jack to the REMOTE PTT socket (8) on the

front panel of the radio.

20. Velcro Strap

Velcro strap for installing the remote PTT control in a

convenient location, such as on the speed shift lever or

on the steering wheel.

18 20 19

- 8 -

TRANSMITTING MODES

OPERATION IN PTT MODE WITH STANDARD MICROPHONE (supplied)

Connect the 4-pin standard microphone to the microphone connector (12). Press and hold the PTT button (16) to

transmit and speak into microphone. Release the PTT button (16) to return to receive mode.

OPERATION IN PTT MODE WITH EXTERNAL MICROPHONE (optional)

AND REMOTE PTT CONTROL BOX (optional)

The optional external microphone (ESM-444) and remote PTT control Box (RPT-1) allow operating the radio in total

comfort and safety, without using the standard microphone that may be disconnected from the radio and removed.

Connect the microphone jack (23) into the EXT MIC socket (11). Connect the remote PTT control jack (19) to the

REMOTE PTT socket (8). Install the remote PTT control in a convenient location, such as on the speed shift lever or on

the steering wheel, using the velcro strap (20), for your most comfortable operation during driving.

WARNING ! Pay the greatest attention to installation of the remote PTT control and its connecting cable, in order

for these not to interfere with your driving operation.

Press and hold the PTT button (18) to transmit and speak into microphone (22) with normal voice. Release the PTT

button (18) to return to receive mode.

Controls, Indicators and operation

English

EXTERNAL MICROPHONE ESM-444 (OPTIONAL)

21. Neck Bracket

22. Microphone

23. Microphone Jack

Connect this jack to the EXT MIC socket (11) on the front panel of the radio.

- 9 -

Installation

Before installing the main unit in the vehicle, check and select the most convenient location, in order that the radio will be

easy to reach and comfortable to operate, without disturbing or interfering with the vehicle drive. Use the supplied

bracket and hardware to install the radio. The bracket screws must be well tightened in order not to become loosen with

the vehicle vibrations. The car mounting bracket can be installed over or below the radio and the radio may be inclined

as desired according to the specific type of installation (under dashboard or track cabin roof installation).

Installation of the Main Unit

Before connecting the radio to the vehicle electric system, make sure that radio is switched off, with the OFF/VOL knob

(10) completely turned counter clockwise at OFF position. The DC power cable (15) of the radio is complete with a fuse

holder with fuse located on the red positive (+) wire. Connect the DC power cable to the vehicle electric system, with

special attention to respect correct polarity, even if the radio is protected against polarity inversion. Connect the red wire to

the positive (+) pole and the black wire to the negative (-) pole of the vehicle electric system. Make sure that the wires and

terminals are firmly and stably connected, in order to prevent cables from disconnecting or causing short circuits.

Installation of the Antenna

A specific mobile antenna adjusted for 27 MHz frequency range must be used. The antenna installation must be done by

a specialised technician or service centre. Please pay special attention to carefully install the antenna on the vehicle with

perfect connection to ground. Before connecting the antenna to the radio, it is necessary to check the correct operation

of the antenna with low standing wave ratio (S.W.R.), using adequate instruments. If not, the transmitter circuit of the

radio could be damaged. The antenna must be usually installed on the highest part of the vehicle, free from obstacles

and as far away as possible from any source of electric or electromagnetic noise. The RF antenna coaxial cable must

not be damaged or pressed on its way between antenna and the radio. The correct operation of the antenna and the low

standing wave ratio (S.W.R.) must be checked periodically. Connect the RF antenna coaxial cable to the antenna

connector (14), located on the rear side of the radio.

Checking Operation of the Radio

Once radio has been connected to the vehicle electric system and to the antenna, the correct operation of the system

may be checked. Please proceed as follows :

1) Check that the power cable (15) is correctly connected.

2) Check that the RF antenna coaxial cable is correctly connected.

3) Connect the standard 4-pin microphone to the connector (12), located on the front side of the radio.

4) Rotate the AS/SQL knob (9) counter clockwise.

5) Turn radio on using the OFF/VOL knob (10) and adjust volume to the desired level.

6) Select the desired channel, using the Up/Down Keys (6, 7).

7) Rotate the AS/SQL knob (9) clockwise, to cut the background noise.

8) Press the PTT key (16) to transmit and release it to receive.

English

Frequency bands table - User Information

- 10 -

Frequency Bands Table

The transceiver INTEK M-60 PLUS includes an advanced multi-standard programmable circuit, which allows to program

different frequency bands, specifications and operating modes, in conformity with the regulations in the country where

the product is used. 9 programmable frequency bands are available, as per the below table :

Attention ! This radio has been factory pre-programmed on the CE frequency band (CEPT 40CH FM 4W), since this

standard is currently accepted in all the European countries. Please refer to the information table at page I (Restrictions

on the use of CB transceivers).

User Information

in accordance with art. 13 of the Legislative Decree of 25th July 2005, no. 15 ”Implementation of Directives 2002/95/EC,

2002/96/EC and 2003/108/EC, relative to reduction of the use of hazardous substances in electrical and electronic

equipment, in addition to waste disposal”.

The crossed bin symbol shown on the equipment indicates that at the end of its working life the product must

be collected separately from other waste.

The user must therefore take the above equipment to the appropriate differentiated collection centres for

electronic and electro technical waste, or return it to the dealer when purchasing a new appliance of

equivalent type, in a ratio of one to one.

Appropriate differentiated waste collection for subsequent recycling, treatment and environment-friendly disposal of the

discarded equipment helps to prevent possible negative environmental and health effects and encourages recycling of

the component materials of the equipment.

Illegal disposal of the product by the user will be punished by application of the administrative fines provided for by the

legislative decree no. 22/1997 (article 50 and following of the legislative decree no. 22/1997).

FREQUENCY BAND

ID CODE

COUNTRY

SPECIFICATIONS

(Channels, Operating Modes, TX Power)

E1 ITALY/SPAIN

40CH AM / FM 4W

I2 ITALY

36CH AM / FM 4W

dE GERMANY

80CH FM 4W - 12CH AM 1W

d2 GERMANY

40CH FM 4W - 12CH AM 1W

EU EUROPE/FRANCE

40CH FM 4W - 40CH AM 1W

CE CEPT

40CH FM 4W

UUK

40CH FM 4W UK FREQUENCIES

40CH FM 4W CEPT FREQUENCIES

PL POLAND

POLAND

40CH AM / FM 4W POLISH FREQUENCIES

40CH AM 1W / FM 4W POLISH FREQUENCIES

English

Frequency band selection / programming

- 11 -

Frequency Band Selection / Programming

This two-way CB radio has to be programmed and exclusively used on a frequency band allowed in the country where

the product is used. When radio is switched ON, the current programmed frequency band code will be displayed

(blinking) for about 3 seconds. To program a different frequency band, proceed as follows :

1) Turn OFF the radio.

2) Press and keep pressed the UP key (6), then turn ON the radio using the OFF/VOL knob (10).

3) The current frequency band code (B) will blink on the LCD display (5).

4) Now select the new desired frequency band code by pressing the Up (6) or Down keys (7).

5) Wait for about 5 seconds to confirm and store the new selected frequency band code.

UK/CE CHANNELS SELECTION (FREQUENCY BAND "U")

The "U" band (UK/CE band) includes both UK and CE channels, this band is for use in the UK. All channels can be

scrolled using the Up (6) or Down (7) keys. If a UK channel is selected, the display (5) will show the channel number

(B) and the indication "U". If a CEPT channel is selected the display (5) will show the channel number (B) and the

indication "C".

Table of Restrictions on the Use of CB Transceivers (page I)

The following information are to be considered only just as an indication. They are believed to be correct at the time of

printing this operating manual. It is however the user’s responsibility to check that, in the country where radio is used, the

regulations for the use of CB transceivers have not been modified. User is therefore suggested to contact the local

dealer or local authority, in order to check the current regulations for the use of CB transceivers, before operating this

product. The manufacturer does not take any responsibility if the product is used in violation of the regulations of the

country where the product is used.

Addendum (Updated information on national restrictions)

BELGIUM, UK, SPAIN, SWITZERLAND

In order to use this transceiver in Belgium, UK, Spain and Switzerland, residence must have an individual licence. Users

coming from abroad may freely use the radio in FM mode, while in order to use it in AM mode they must hold a licence

released in their own country.

ITALY

Foreigners arriving in Italy must get an Italian authorization.

AUSTRIA

Austria does not allow using multi standard programmable CB radios. It is recommended

to carefully follow this directives and not to use the product in the Austrian territory.

GERMANY

Along some border areas in Germany, the radio can not be used as a base station from

channel 41 to channel 80. Refer to local authority (notification office) for details.

English

Specifications - Optional Accessories

- 12 -

Specifications

General

Channels 40 FM (refer to the frequency bands table at page 10)

Frequency range 27 MHz Citizen Band

Frequency control P.L.L.

Operatine temperature -10°/+55°C

DC input voltage 13.2Vdc ±15%

Size 115 (L) x 43 (H) x 165 (D) mm

Weight 600 gr.

Receiver

System Double conversion, CPU controlled super-heterodine

IF 1° 10.695 MHz / 2° 455 KHz

Sensitivity 0.5uV (FM)

0.5uV (AM)

Audio output 2.5W

Audio distorsion <8% at 1 KHz

Image rejection 65dB

Signal/noise ratio 45dB

Current drain 300mA (stand-by)

Transmitter

System CPU controlled P.L.L. systhesizer

Maximum RF power 4W at 13.2Vdc

Modulation 85% to 90% (AM)

1.8 KHz ±0.2 KHz (FM)

Impedance 50 ohm unbalanced

Current drain 1200mA (at no modulation)

Opzional Accessories

ESM-444 External microphone with adjustable flexible boom and neck support

RPT-1 Remote PTT Control Box with velcro strap and 2 mt cable with jack

RECOMMENDED BY INTEK !

LEADER IN CB 27 MHz

CAR & TRUCK MOBILE ANTENNAS

English

Indice - Introduzione

- 13 -

Indice - Introduzione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Disimballaggio e verifica delle parti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Accessori forniti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Descrizione dei comandi e funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-20

Installazione e collegamenti elettrici . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Tabella bande di frequenza - Avviso agli utenti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Selezione / programmazione della banda di frequenza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Tabella delle restrizioni all' uso dei ricetrasmettitori CB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Caratteristiche tecniche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Tabella delle restrizioni all' uso dei ricetrasmettitori CB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I

Circuito stampato Main Board e Front Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II-III

Schema elettrico . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IV-V

Schema a blocchi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VI-VII

Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VIII-IX

IMPORTANTE !

Prima di utilizzare la ricetrasmittente, verificare che la stessa sia programmata per operare sulle

bande di frequenza e nei modi previsti dalle norme di legge in vigore nel paese in cui la radio viene

utilizzata. Diversamente procedere alla modifica della programmazione, come indicato in questo

manuale di istruzioni. La radio è pre-programmata all' origine sulla banda di frequenza europea CE

(CEPT 40CH FM 4W).

Congratulazioni !

Congratulazioni per aver scelto ed acquistato un prodotto di qualità INTEK. Questo ricetrasmettitore dispone di numerose

funzioni avanzate e vari dispositivi, pertanto è assolutamente necessario leggere attentamente questo manuale di

istruzioni prima di utilizzare l' apparecchio. Con un uso corretto secondo quanto è indicato nel manuale di istruzioni, l'

apparecchio garantirà un servizio senza problemi per molti anni. Ci impegnamo costantemente a fornire prodotti di

qualità che rispondano alle vostre esigenze, ma siamo comunque sempre molto interessati a ricevere eventuali vostri

commenti o suggerimenti su questo prodotto, che ci aiutino nel continuo miglioramento della qualità. INTEK M-60

PLUS è un ricetrasmettitore con caratteristiche tecniche di hardware e software molto avanzate e dispone di un circuito

di tipo Multi Standard programmabile che consente di configurare i vari parametri dell' apparecchio (bande di

frequenza, modi operativi, potenza del trasmettitore) in modo conforme alle norme di legge in vigore nei vari paesi

della Comunità Europea. Pertanto questa ricetrasmittente può essere utilizzata in un qualsiasi paese della Comunità

Europea. L' apparecchio viene consegnato pre-programmato sulla banda CE (CEPT 40CH FM 4W).

Italiano

Disimballaggio e verifica delle parti - Accessori forniti

Disimballaggio e verifica delle parti

Disimballate accuratamente il ricetrasmettitore. Si raccomanda di identificare tutte le parti elencate nella tabella

seguente, prima di eliminare l’imballo. Se vi sono stati danni o mancanze durante la spedizione, contattate

immediatamente il vostro fornitore.

Accessori forniti

Cavetto di alimentazione DC con porta fusibile e fusibile integrato con il ricetrasmettitore

Microfono standard con connettore a 4 poli

Staffa di montaggio per veicolo

Accessori per montaggio staffa (viti, pomelli, ecc.)

Staffa di supporto per microfono

Manuale di istruzioni

Supporto per il microfono Staffa di montaggio Manuale di istruzioni

Viteria

Cavo di alimentazione

con porta fusibile e fusibile

integrato con il ricetrasmettitore

Microfono

- 14 -

Italiano

Descrizione dei comandi e funzionamento

- 15 -

1. Tasto A/F

Questo tasto consente di selezionare il modo operativo AM o FM, in TX e RX, se il modo scelto è abilitato dalla banda di

frequenza programmata.

2. Tasto ANL (Automatic Noise Limiter)

Premere il tasto ANL (2) per inserire il dispositivo ANL (Automatic Noise Limiter) che permette la riduzione dei disturbi

radio elettrici ed elettromagnetici sul canale in uso. L' icona ANL (D) sarà accesa a conferma dell' inserimento del

dispositivo. Ripremere il tasto ANL (2) per disattivare il dispositivo ANL.

3. Tasto EMG (Emergency Channels)

Questo tasto permette la selezione rapida di uno dei 2 canali di emergenza pre-programmati (CH9 o CH19). Ad ogni

pressione del tasto EMG (3), viene impostato il canale CH9, quindi il canale CH19, quindi nuovamente il normale

canale in uso.

4. Indicatore BUSY

Indicatore LED di colore verde, è acceso quando la radio sta ricevendo una comunicazione e lo Squelch è aperto (la

radio non si trova in modalità mute).

5. Display LCD

Ampio display LCD di tipo retroilluminato in colore blu, per la massima leggibilità. Il display indica il numero del canale in

uso, il modo operativo e tutte le funzioni e i dispositivi attivati.

1 2 3 4 5 6

7911 812 10

PANNELLO FRONTALE

Italiano

Descrizione dei comandi e funzionamento

- 16 -

A. Icona AM

L' icona AM (A) è accesa quando il ricetrasmettitore riceve e trasmette in modo AM (modulazione di ampiezza).

B. Indicazione del canale

Indica il numero del canale in uso o la banda di frequenza selezionata.

C. Strumento a barre S/RF Meter

Strumento digitale S/Meter a 5 barre, indica l' intensità del segnale ricevuto da S0 a S9+30 in ricezione e la potenza RF

di uscita da 0 a 4W in trasmissione.

D. Icona ANL

L' icona ANL (D) è accesa quando è abilitato il dispositivo ANL (Automatic Noise Limiter).

C. Icona TX

L’ icona TX (C) è accesa quando il ricetrasmettitore è in modalità trasmissione.

E. Icona ATT

Non disponibile in questo modello.

F. Icona H

L' icona H (F) è accesa quando il trasmettitore è in modalità alta potenza del trasmettitore (4W).

G. Icona L

L' icona L (G) è accesa quando il trasmettitore è in modalità bassa potenza del trasmettitore (1W).

H. Icona FM

L' icona FM (H) è accesa quando il ricetrasmettitore riceve e trasmette in modo FM (modulazione di frequenza).

DISPLAY LCD

Italiano

- 17 -

Descrizione dei comandi e funzionamento

6. Tasto Up

Premere per selezionare il canale operativo in modo crescente. Mantenendo premuto questo tasto, la selezione dei

canali avverrà in modo rapido.

7. Tasto Down

Premere per selezionare il canale operativo in modo decrescente. Mantenendo premuto questo tasto, la selezione dei

canali avverrà in modo rapido.

8. Presa REMOTE PTT

Presa per il collegamento del comando PTT remoto RPT-1 (opzionale).

Per il funzionamento fare riferimento al paragrafo "MODALITA' DI TRASMISSIONE" a pag. 20.

9. Manopola AS/SQUELCH

COMANDO SQUELCH (regolazione manuale SQUELCH)

Il comando SQUELCH permette di silenziare il ricevitore, eliminando il rumore (fruscio) di fondo in assenza di segnali.

Ruotare la manopola in senso orario sino a quando scompare il rumore di fondo. Ruotare la manopola in senso

antiorario (apertura dello SQUELCH) per ascoltare i segnali più deboli.

COMANDO AS (regolazione fissa SQUELCH)

E' disponibile la funzione AS per silenziare il ricevitore in modo automatico, senza eseguire la regolazione manuale dello

SQUELCH. Una regolazione fissa dello SQUELCH è pre-impostata in origine. Per impostare la funzione AS, ruotare la

manopola completamente in senso antiorario fino a farla scattare in posizione AS.

10. Manopola OFF/VOL

Manopola di accensione e spegnimento della radio. Permette la regolazione del volume di ascolto. In assenza di segnali

sul canale in uso, si consiglia di aprire lo SQUELCH e quindi di regolare il volume al livello desiderato utilizzando come

riferimento il rumore (fruscio) di fondo.

11. Presa EXT MIC

Presa per il collegamento del microfono esterno opzionale ESM-444. Per il funzionamento fare riferimento al

paragrafo "MODALITA' DI TRASMISSIONE" a pag. 20.

12. Presa per microfono

Collegare il microfono tradizionale a 4-poli in dotazione a questa presa, bloccandolo tramite l’ apposita ghiera.

Italiano

IMPORTANTE !

Non tentare mai di aprire il contenitore del ricetrasmettitore. All' interno dell' apparecchio non vi sono parti utili o

utilizzabili dall' utente. Interventi o manomissioni del circuito interno della radio possono causare danni alla stessa

o modificarne le caratteristiche tecniche ed inoltre violano e invalidano il diritto alla garanzia. In caso di interventi

tecnici, rivolgersi esclusivamente ad tecnico o ad un centro di assistenza autorizzato.

13. Presa EXT (External Speaker)

Presa per il collegamento di un altoparlante esterno (opzionale).

14. Connettore di antenna (SO-239)

Presa per il collegamento dell' antenna. Vedi capitoli "installazione e collegamenti elettrici".

15. Entrata POWER 13.2VDC

Entrata del cavetto di alimentazione DC in dotazione.

PANNELLO POSTERIORE

ANT

EXT

13.2V

1413

Descrizione dei comandi e funzionamento

- 18 -

Italiano

La pagina sta caricando ...

INTEK M-60 PLUS Manuale del proprietario

Marca: INTEK

Modello: M-60 PLUS

Categoria: Microfoni

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: INTEK M-60 PLUS Owner's manual

INTEK M-60 PLUS Manuale del proprietario

INTEK M-60 PLUS Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti