Thermex HRW Multicom Guida d'installazione

COD. 5571.084.855 08/07/2021

Libretto istruzioni

Instructions Booklet

Livret d’istructions

Betriebsanleitung

Manual de instrucciones

说明手册

Navod na použivanie

Brugervejledning

VORT HRW 30 MONO EVO WiFi

VORT HRW 30 MONO EVO HCS WiFi

VORT HRW 40 MONO EVO WiFi

VORT HRW 40 MONO EVO HCS WiFi

Read the instructions contained

in this booklet carefully before using

the appliance. VORTICE cannot assume

any responsibility for damage to

property or personal injury resulting

from failure to abide by the instructions

given in this booklet. Following these

instructions will ensure a long service

life and overall electrical and

mechanical reliability. Keep this

instruction booklet in a safe place.

Index EN

Description and use . . . . . . . . . . . . . . . . . . . . . . .28

Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Structure and equipment . . . . . . . . . . . . . . . . . . . .30

VORT HRW 30 MONO EVO WiFi installation . . . .31

VORT HRW 40 MONO EVO WiFi installation . . . .34

Use (fig. 25) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Parameters programming sequences . . . . . . . . . . . . .41

IR Remote Control (HCS models only) . . . . . . . . . . .45

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Maintenance and cleaning . . . . . . . . . . . . . . . . . . . . . . .50

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Før produktet installeres og tilsluttes

bør disse anvisninger læses grundigt.

VORTICE kan ikke betragtes som

ansvarlig for eventuelle skader på

personer eller ting forårsaget af at disse

anvisninger ikke følges. Følg alle

instruktionerne for dermed at sikre

holdbarheden og den elektriske og

mekaniske pålidelighed. Gem derfor

altid denne brugsanvisning.

Indeks DA

Beskrivelse og anvendelse . . . . . . . . . . . . . . . . .172

Overensstemmelse med brugen . . . . . . . . . . . . .172

Bemćrk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173

Struktur og udstyr . . . . . . . . . . . . . . . . . . . . . . . .174

Installation af VORT HRW 30 MONO EVO WiFi .175

Installation af VORT HRW 40 MONO EVO WiFi .178

Anvendelse (fig. 25) . . . . . . . . . . . . . . . . . . . . . . .181

Parameterprogrammeringssekvenser . . . . . . . . . . . .185

IR-fjernbetjening (kun HCS-modeller) . . . . . . . . . . .189

Tekniske specifikationer . . . . . . . . . . . . . . . . . . . . . . . .192

Vedligeholdelse og rengøring . . . . . . . . . . . . . . . . . . .194

Husholdningsapparater . . . . . . . . . . . . . . . . . . . . . . . . .195

Description and use

VORT HRW MONO EVO WiFi (hereinafter 'the device') is a decentralised heat recovery ventilation system with

an integrated WiFi module for synchronisation with several units. The device can be wall-mounted in perimeter

walls between 260 mm (283 mm for VORT HRW 40 MONO EVO WiFi) and 700 mm thick.

The device is available in four versions:

- Installation inside holes with a nominal diameter of 100 mm and a maximum air flow rate (in boost mode) of

38 m3/h:

• VORT HRW 30 MONO EVO WiFi with on-board machine controls.

• VORT HRW 30 MONO EVO HCS WiFi with remote control and relative humidity, temperature and

ambient light sensors.

- Installation inside holes with a nominal diameter of 160 mm and a maximum air flow rate (in boost mode) of

40 m3/h:

• VORT HRW 40 MONO EVO WiFi with on-board machine controls.

• VORT HRW 40 MONO EVO HCS WiFi with remote control and relative humidity, temperature and

ambient light sensors.

Humidity, temperature and ambient light sensors. integrated in HCS versions, allow the automatic operation of

the device (“Auto HR%”, “Auto Comfort”, “Auto night” functions).

- Maximum absorbed power VORT HRW 30 MONO EVO WiFi: 5W.

- Maximum absorbed power VORT HRW 40 MONO EVO WiFi: 6W.

Common features for all models:

- WiFi module for Mesh network.

- Buttons with LED indicators.

- 5 speeds corresponding to 5 airflows.

- 1 input suitable for remote connection with cable compatible with external modules "VORTICE C TEMP"

(temperature sensor) and "VORTICE C HCS" (humidity sensor) or equivalent. Cable length30m.

- 1 direct output for fan control.

- Long-term timer (3/6/12 months) with daily increase for filter clogging control.

- Insulation class: II.

- Power supply: 220-240V ~ 50-60Hz.

Compliance

•This appliance can be used by children no less than 8 years of age

and by individuals with limited physical, sensory or mental capacities,

or by inexperienced or untrained individuals, provided that they are

supervised or have been instructed in safe use of the appliance and

understand the associated risks. Children must not play with the

appliance. Cleaning and maintenance procedures that can be

undertaken by the user must not be entrusted to children, unless

under supervision.

•These appliances are designed for use in residential and commercial

properties.

•The appliance must be installed by a professionally qualified

electrician.

•The electrical system to which the product is connected must be in

compliance with applicable regulations.

•An omnipolar switch with a contact opening distance of 3 mm or

higher should be provided for installation, enabling complete

disconnection under overvoltage category III conditions.

•Products equipped with single-phase wiring (M) engines ALWAYS

require connection to 220-240V (or only 230V where required) single-

ENGLISH

28

phase lines. Any kind of modification shall be considered as product

tampering and shall nullify the relative warranty.

•Precautions must be taken to prevent gas coming from the gas flue

pipe or from other fuel combustion units from entering into the room.

•Fans have been designed to be mounted on external walls.

Safety

• Follow the safety instructions to prevent any harm to the user.

• Do not use this appliance for purposes other than those described in this manual.

• Having removed the appliance from its packaging, make certain that it is intact and undamaged. If in doubt,

consult a professional or contact an authorized VORTICE Service Centre.

• Do not leave packaging within reach of children or individuals with disabilities.

• Certain basic rules must always be observed when using any electrical appliance: never touch the appliance

with wet or damp hands; never touch the appliance when barefoot.

• Do not operate the appliance in the presence of flammable substances or vapours, such as alcohol, insecticides,

petrol, etc.

• If the appliance is to be disconnected from the power supply and no longer used, store it out of reach of children

and individuals with disabilities.

• Do not make modifications of any kind to this appliance.

• The maintenance instructions must be followed to ensure the appliance does not suffer damage and/or excessive

wear.

• Do not expose this appliance to the elements (rain, sun, etc.).

• Do not stand objects on the appliance.

• The inside of the appliance must be cleaned only by a skilled professional.

• Inspect the appliance periodically for visible defects. If the appliance is defective in any way, do not use it; contact

a VORTICE authorized Technical Support Centre without delay.

• If the appliance does not function correctly or develops a fault, contact a VORTICE authorized Technical Support

Centre without delay. Ensure that only genuine original VORTICE spares are used for any repairs.

• Should the appliance be dropped or suffer heavy impact, have it checked without delay by a VORTICE authorized

Technical Support Centre.

• The appliance must be installed in such a way as to ensure that under normal operating conditions, no one can

come into contact with any moving parts or live electrical components.

• In the event of: dismantling the appliance with the appropriate tools, removing the heat exchanger for cleaning

recommended: every six months)or removing the motor module, the appliance must first be switched off and

disconnected from the electrical power supply.

• Connect the appliance to the electrical power supply/socket only if the rated power of the supply is compatible

with the maximum rated power of the appliance. If not, contact a professional electrician without delay.

• Turn off the appliance at the main switch: if the appliance does not function correctly, before cleaning the outside

of the appliance, or if the appliance is not going to be used for any length of time.

• The flow of extracted air must be clean (i.e. free of grease, soot, chemical and corrosive agents and explosive or

flammable mixtures).

• Keep the air intake and outlet ports of the appliance free of obstructions, to ensure optimum air flow.

• Operating temperature range: -20 ÷ 50°C.

• Specifications for the power supply must correspond to the electrical data on the

plate (A).

ENGLISH

Warning:

this symbol indicates that care must be taken to avoid injury to the user.

!

A

Caution:

this symbol indicates that care must

be taken to avoid damaging the appliance

!

29

Structure and equipment

Components common to all models

The main components of the device are:

• main body (1) already assembled which includes:

- Body with pre-assembled plug-in terminal block, frontal grille and aesthetic panel in polycarbonate (PC) tested

according to standard UNI EN ISO 11925-2:2010 and resulted in class E for reaction to fire (according to the

EN 13501-1 standard).

- Motor holder and push-button panel in ABS material.

- 5-speed reversible EC fan.

- Integrated electronic board.

- Closing device (disk) sealing the front panel to prevent temperature changes in the winter months and the entry

of pollutants and odors from the outside.

- Washable internal filter with frame.

• Flange (2) wall mountable with pre-assembled terminal block.

• Terminal block cover with screw and cable gland (3).

• PVC pipe for installation inside walls with thickness from 260 mm (283 mm VORT HRW 40 MONO EVO WiFi)

to 700 mm (optional).

VORT HRW 30 MONO EVO WiFi

• Storage type heat exchanger, made of ceramic material with external filter already assembled (4A)

• External ventilation grille (d.100 T10 RB) in plastic material, externally mountable. Grid equipped with anti-insect

net (5A).

VORT HRW 40 MONO EVO WiFi

• Storage type heat exchanger, made of ceramic material supplied with two expanded polyproylene (EPP)

housings and it is complete with a central gasket to prevent air infiltration (4B).

• Outer rubber grille (5B), which can be mounted externally with plugs or inserted internally through the hole in

the wall with no need for external scaffolding.

• Washable external filter with holder grids (x2) (6)

• Insect grid (7)

VORT HRW 30 MONO EVO HCS WiFi / VORT HRW 40 MONO EVO HCS WiFi

• Remote control (8).

ENGLISH

VORT HRW 30 MONO EVO WiFi VORT HRW 40 MONO EVO WiFi

(HCS models)

(1)

(3) (4A)

(5A)

(6)

(5B)

(4B)

(8)

(HCS models)

(8)

(3)

(2)

(7)

(1)

30

ENGLISH

VORT HRW 30 MONO EVO WiFi installation

Fig 1 ÷ 11

NOTE: before proceeding with the installation, remove the internal protective packaging in the appliance.

NOTE: before carrying out installation, remove the spacers inside the PVC installation pipe (provided as

accessory) and cut the pipe according to the wall thickness.

It is mandatory to install VORT HRW 30 MONO EVO WiFi within a perimeter wall with a thickness of at least 260

mm.

1

IN OUT

mm 102

ø

≥260 mm

2°÷3°

2

31

ENGLISH

3

4

Drill the two holes for the power cables

and PCB signal cables inside the dotted

area.

4

5

6

TERMINAL BLOCK

MAIN BIPOLAR SWITCH

1

2

LN

GND

IN

L

N

1

2

MAINS

220-240V~50-60Hz

LOW VOLTAGE

Remote Unit Sync Bus

L, N

UNIT #1

L, N

UNIT #2

220-240V~50-60Hz 220-240V~50-60Hz

7

IR

REMOTE

CONTROL

IR

REMOTE

CONTROL

WiFi

Mesh

Network

32

ENGLISH

8

9

10

11

CLACK!

33

VORT HRW 40 MONO EVO WiFi installation

Fig 12 ÷ 24

NOTE: before proceeding with the installation, remove the internal protective packaging in the

appliance.

NOTE: before carrying out installation, remove the spacers inside the PVC installation pipe (provided as

accessory) and cut the pipe according to the wall thickness.

It is mandatory to install VORT HRW 40 MONO EVO WiFi within a perimeter wall with a thickness of at least

283 mm.

ENGLISH

IN OUT

mm 162

ø

12

≥283 mm

2°÷3°

13

GLUE

UP

123

4 5 6

VORT HRW 40 MONO EVO WiFi - GRILLE MOUNTING - FROM INSIDE

34

ENGLISH

VORT HRW 40 MONO EVO WiFi - GRILLE MOUNTING - FROM OUTSIDE

14

1 2

3 4

15

16

Drill the two holes for the power cables

and PCB signal cables inside

the dotted area.

35

17

ENGLISH

TERMINAL BLOCK /

MAIN BIPOLAR SWITCH /

1

2

L N

GND

IN

L

N

1

2

MAINS

220-240V~50-60Hz

LOW VOLTAGE

Remote dry contact

18

18A18A

L, N

UNIT #1 UNIT #2

REMOTE CONTROL

IR

REMOTE CONTROL

IR

220-240V~50-60Hz

WiFi

Mesh

19

20

INSERTING METALLIC MESH FILTER

!

2121 VORT HRW 40 MONO EVO WiFi - INSERTING THE EXTERNAL FILTER

36

ENGLISH

22

23

2424

CLACK!

Use (fig. 25)

To use the appliance, make sure the lever of the closing disk is in the open position, by rotating the lever to position

2.

1

2

25

37

ENGLISH

DESCRIPTION OF THE UNIT COMMANDS

Warning (fig. 26A):

The control panel is accessible by inserting the hand in the space between the cover and the

front grille (1) or by lifting up the cover (2).

!

26A

12

The device is controlled by means of on-board buttons (Fig. 26B).

PULSANTE

VELOCITÀ

PULSANTE

MODALITÀ

PULSANTE

FUNZIONE

LED 1

LED 2

LED 3

LED 4

LED

RECUPERO/AUTO NIGHT

LED

IMMISSIONE/AUTO HR%

LED

ESTRAZIONE/AUTO COMFORT

LED 5

A

D

C

B

/ Night

/ Quiet

/ Boost

/ Performance

/ High

Performance

26B

A: SPEED KEY: 5 position selector (Night / Quiet / Performance / High performance / Boost).

LED 1- LED 5: speed / air flow from min to max. Press the button cyclically to select the desired value. The

white LEDs from 1 to 5 will light up to indicate the speed from 1 to 5.

B: MODE KEY: three position selector. Press repeatedly to cycle through the different modes: recovery, intake,

extraction, natural ventilation (intake and extraction LEDs switch on simultaneously).

The respective LEDs will light up steadily:

•RECOVERY heat recovery (the system works like an heat recovery unit, with cyclic inversion of the direction

of rotation).

•INTAKE the system operates as a fan, with room air intake.

•EXTRACTION the system works as a fan, with air extraction from the room.

•NATURAL VENTILATION If the device is connected to one or more units via a WiFi network, the NATURAL

VENTILATION mode can be set: if set as an even unit the device will operate in extraction mode, if set as an

odd unit the device will operate in intake mode, creating an air current in the environment.

Note 1: In the HCS versions, natural ventilation can be selected automatically via the external IR remote

38

control (see fig. 30).

Note 2: The WiFi module allows to balance the air flow rates of intake and extracted air, provided that the

total number of installed units is equal to an even number. For example, 4 units can be connected

to the WiFi network, setting two units as “even” and two units as “odd”. Air flow balancing will

not occur if an odd number of units is installed.

Note 3: To see how to set the device as an even or an odd unit, refer to the section "parameter

programming sequences".

Note 4: The backlighting of the keys on the device remains active for one minute from the last press of

any key.

Note 5:The backlighting of the keys on the remote control of HCS versions remains active for 15 seconds

from the last press of any key.

C: FUNCTION KEY to activate or deactivate the 3 different AUTO functions available and activate or deactivate

the stand-by mode.

To activate or deactivate the stand-by mode:

If the device is switched on and the FUNCTION key is pressed (stand-by / on-off function), the fan stops and the

LEDs of the SPEED column turn off. If the appliance is off and you press the FUNCTION button, the appliance

starts at the speed and mode previously set.

The available functions are:

• Auto night (only for HCS models)

The ambient light sensor detects the presence or absence of ambient light and, depending on whether the

measurement is higher or lower than the threshold value set via SW (fixed value that cannot be changed

by the user) it allows or prevents both the switch to a speed higher than the minimum both the transition

to boost speed via remote input or HR% sensor.

Therefore, at night when the presence of daylight is not detected, the appliance switches to minimum

speed preventing the switch to a speed higher than the minimum one.

When the presence of daylight is detected again, the appliance returns to operate at the previously set

speed, and it is allowed the switch to higher speeds or boost via remote input or HR% sensor.

• Auto HR%

In case of presence of humidity beyond the alarm threshold (60%, 75% or 90% - the default value is

75%), it is automatically selected the extraction mode at maximum speed.

•Auto comfort

In heat recovery mode, the period that determines the inversion of rotation of the fans is fixed based on

the temperature of the air introduced into the room: if too cold, the cycle time is reduced.

ENGLISH

To enable a function (fig. 27):

1) press the FUNCTION button for more than 2 seconds.

2) press the SPEED button to select one of the three LEDs

(LED 1, LED 2, LED 3) corresponding to the

AUTONIGHT / AUTO HR% / AUTO COMFORT

functions.

3) press the MODE button to enable the function -> the

chosen LED in the mode column blinks.

4) to SAVE the settings, press the FUNCTION button for

more than 2 seconds.

All SPEED LEDs blink 4 TIMES to indicate correct

storage.

5) to CANCEL and exit the setting procedure, press the

FUNCTION key once. All SPEED LEDs blink ONLY

ONCE WITHOUT SAVING any changes made.

6) to CHECK which function is assigned to the appliance,

press the FUNCTION button for more than 2 seconds:

the LED corresponding to the set function blinks for

about 20 seconds, then all the speed LEDs flash and

the device returns to standard display.

Note: The user can enable all the three functions

simultaneously.

SPEED

BUTTON

LED 1

LED 2

LED 3

LED 4

LED

RECOVERY

FUNCTION

BUTTON

/AUTO NIGHT

LED

INTAKE /AUTO HR%

LED

EXTRACTION/AUTO COMFORT

LED 5

1 23

27

MODE

BUTTON

39

ENGLISH

To disable a function (fig. 28):

1) press the FUNCTION button for more than 2 seconds.

2) press the SPEED button to select one of the three LEDs

(LED 1, LED 2, LED 3) corresponding to the

AUTONIGHT / AUTO HR% / AUTO COMFORT function

to be disabled.

3) press the MODE button to disable the function.

4) to SAVE the settings, press the FUNCTION button for

more than 2 seconds. All SPEED LEDs blink 4 TIMES to

indicate correct storage.

5) to CANCEL and exit the setting procedure, press the

FUNCTION key once. All SPEED LEDs blink ONLY

ONCE WITHOUT SAVING any changes made.

6) to CHECK which function is assigned to the appliance,

press the FUNCTION button for more than 2 seconds: :

the LED corresponding to the set function blinks for about

20 seconds, then all the speed LEDs flash and the device

returns to standard display.

2828

LED 1

LED 2

LED 3

LED 4

LED 5

1 23

LED

EXTRACTION/AUTO COMFORT

LED

INTAKE /AUTO HR%

LED

RECOVERY/AUTO NIGHT

FUNCTION

BUTTON

MODE

BUTTON

SPEED

BUTTON

D: FILTER LED

One led (D - fig. 26B) shows the status of the filters:

• LED OFF: filters are clean

• LED ON: filters to be cleaned or replaced (for each day of operation, a counter in the memory is increased

and when the maximum preset time is reached (90/180/365 days), the signalling LED lights up).

Refer to section “maintenance and cleaning”.

CLOSING OF THE DEVICE

To avoid air to come inside the room, set the device in stand-by mode by pressing the FUNCTION key (LEDs in

the SPEED column switch off) and turn the lever to close position (fig. 29).

2

1

29

40

ENGLISH

Parameters programming sequences

By means of appropriate actions on the keyboard buttons, it is possible to reset the clogged filter counter, or

program the unit's operating parameters, as specified below:

To entry in programming mode:

• Press simoultaneously all the three buttons (SPEED - MODE - FUNCTION).

• LED 5 turns on white.

• Press the buttons in the following sequence: SPEED - SPEED - MODE - FUNCTION - FUNCTION – MODE.

To set the relative humidity threshold:

• Press the SPEED button.

• The currently set threshold is displayed by lighting one of the white LEDs 1, 2 or 3 depending on whether the

value is 60%, 75% or 90% (the default value is 75%).

• Press SPEED button to modify the threshold value.

• Press the FUNCTION button to confirm.

• All the speed LEDs from 1 to 5 will blink briefly to indicate that the value has been stored and the device will

return to normal operation.

• If you do not press the FUNCTION button within 20 sec, the device will return to normal operation without

storing.

To select cycle time:

• Press MODE button.

• The currently set time is displayed by lighting one of the white LEDs in position 1, 2 or 3 depending on whether

the time is 50, 60 or 90s. (Default value = 60s).

• Press the SPEED button to change the value.

• Press the FUNCTION button to confirm.

• All the speed LEDs from 1 to 5 will flash briefly to indicate successful storage and the device will return to

normal operation.

• If the FUNCTION button is not pressed within 20 sec, the device will return to normal operation without

memorizing.

NOTE: Cycle time programming can only be carried out on the unit set as master.

To select the clogged filter alarm interval:

• Press the FUNCTION button.

• The time currently set is displayed by lighting one of the white LEDs in position 1, 2 or 3 depending on whether

the interval is equal to 90, 180 or 365 days.

• Press the SPEED button to modify the value.

• Press the FUNCTION button to confirm.

• All the speed LEDs from 1 to 5 will blink briefly to indicate that the storage has taken place and the equipment

will return to normal operation.

• If the FUNCTION key is not pressed within 20 sec, the device will return to normal operation without

memorizing.

To reset the clogged filter counter:

• Press the SPEED - MODE - FUNCTION buttons simultaneously.

• Press the buttons in the following sequence: MODE - MODE - SPEED - SPEED - MODE - MODE.

• Press the Function key within 20 sec.

• All the speed LEDs from 1 to 5 will blink briefly to indicate that the reset has taken place and the device will

return to normal operation.

• If the FUNCTION button is not pressed within 20 sec, the device will return to normal operation without having

reset the filter timer.

Note: for regular operation between multiple devices, it is necessary to set the type of unit

(Master / Slave and Even / Odd)

!

To set the device as "WiFi Mesh" Master:

• Press simultaneously the SPEED - MODE - FUNCTION buttons.

• Press in sequence the following buttons: MODE - MODE - SPEED - SPEED - FUNCTION - FUNCTION.

• Press the Mode button within 20 sec.

• All speed LEDs from 1 to 5 will blink briefly to indicate that the device has been set as master unit.

• If you do not press the MODE button within 20 sec, the device will return to normal operation without making

any changes to the settings.

41

To set the device as “WiFi Mesh" Slave:

• Press simultaneously the SPEED - MODE - FUNCTION buttons.

• Press in sequence the following buttons: MODE - MODE - SPEED - SPEED - FUNCTION - FUNCTION.

• Press the SPEED button within 20 sec.

• All speed LEDs from 1 to 5 will blink briefly to indicate that the device has been set as Slave.

• If the SPEED button is not pressed within 20 sec, the device will return to normal operation without making any

changes to the settings.

To set the device as "Even Unit":

• Press simultaneously the buttons: SPEED - MODE - FUNCTION

• Press in sequence the buttons: SPEED - SPEED - FUNCTION - FUNCTION - MODE - MODE.

• Press the SPEED button within 20 sec.

• All speed LEDs from 1 to 5 will blink briefly to indicate that the device has been set as an even numbered unit.

• If the SPEED button is not pressed within 20 sec, the device will return to normal operation without making any

changes to the settings.

To set the device as an "Odd Unit":

• Press simultaneously the SPEED - MODE - FUNCTION buttons.

• Press in sequence the buttons SPEED - SPEED - FUNCTION - FUNCTION - MODE - MODE.

• Press the FUNCTION key within 20 sec.

• All speed LEDs from 1 to 5 will blink briefly to indicate that the device has been set as an odd-numbered unit.

• If the Function button is not pressed within 20 sec, the device will return to normal operation without making

any changes to the settings.

ENGLISH

Note: only one unit must be set as MASTER in a specific network . The other units must be set as

SLAVE

!

WiFi Mesh Network

The WiFi module creates a mesh wifi network to synchronize the units. The mesh network is identified by a particular

SSID (Service Set Identifier), which will be generic by default during installation and will become unique for each

particular network once installation is completed.

To set the SSID (Service Set Identifier) of the WiFi mesh network

• Press the SPEED - MODE - FUNCTION buttons on the MASTER unit at the same time.

• Press the MODE - MODE - SPEED - SPEED - MODE - MODE buttons in sequence.

• Press the SPEED button within 20 seconds

• All speed LEDs from 1 through 5 will briefly blink to indicate that SSID = VOR_XXXXXXXX has been set on

EACH SINGLE UNIT IN THE NETWORK

• If the SPEED button is not pressed within 20 seconds, all SPEED LEDs from 1 to 5 will light up for 1 second

without blinking to indicate that the appliance will return to normal operation without resetting the network

SSID.

!The machines are set as SLAVE by factory default. You must therefore set a unit as MASTER by

pressing the MODE - MODE - SPEED- SPEED - FUNCTION – FUNCTION buttons in sequence and

then the MODE button.

!Note: The change from the default network SSID "VORTICE_HRW" to a unique network SSID is

mandatory in order to prevent interference between different devices belonging to different

networks (for example, in the case of two independent flats separated by a wall, etc.).

!Note: you must have a smartphone or network detection device handy to view the names of the

assigned networks.

42

ENGLISH

To set the SSID in the case of two installed networks (for example two networks on two different

floors) follow these steps:

1) Switch off the units that are not part of the network on which you want to operate (for

example those on the upper floor if you want to set the network on the lower floor) to prevent

them not to be assigned the same SSID.

2) Then, from the MASTER unit, assign the unique network identifier (SSID) by pressing the

MODE - MODE - SPEED - SPEED - MODE – MODE buttons in sequence and then the SPEED

button.

3) To set up another network (the upper floor in the example), you do not need to turn off the

units of the other set up network as they already have a unique SSID.

!

To reset the mesh WiFi network (global / all network units) SSID:

• Press the SPEED - MODE - FUNCTION buttons at the same time.

• Press the MODE - SPEED - FUNCTION - MODE - SPEED- FUNCTION buttons in sequence.

• Press the MODE button within 20 second

• All the speed LEDs from 1 to 5 will flash briefly to indicate execution of the command:

- Reset the SSID = VORTICE_HRW (default) FOR ALL UNITS ON THE NETWORK.

• If the MODE button is not pressed within 20 seconds, all speed LEDs 1 to 5 will light up for 1 second without

flashing, indicating that the machine will return to normal operation without resetting the network SSID.

To reset the WiFi mesh network (local / single unit on the network) SSID:

• Press the SPEED - MODE - FUNCTION buttons set as SLAVE at the same time.

• Press the MODE - MODE - SPEED - SPEED - MODE - MODE buttons in sequence..

• Press the SPEED button within 20 seconds

• All the SPEED LEDs from 1 to 5 will blink briefly to indicate that SSID = VORTICE_HRW (default) has been

reset FOR THE SINGLE UNIT ONLY.

• If the SPEED button is not pressed within 20 seconds, all SPEED LEDs from 1 to 5 will light up for 1 second

without blinking to indicate that the appliance will return to normal operation without resetting the network

SSID.

MAC Address and SSID

The MAC Address is assigned by the manufacturer of the WiFi module itself and it is unique.

The last 4 hexadecimal digits of the MAC Address (UAA = Unique Address Assignment) of the master unit are

used to generate the unique SSID of the network:

VOR_XXXXXXXX (e.g. VOR_34F5E4E7)

Each digit consists of two hex characters ranging from 0 to 255 (0x00-0xFF).

The default SSID is instead VORTICE_HRW with default password = "12345678" which cannot be changed.

Adding one or more new units to an existing mesh network

1. Go into programming mode by pressing simultaneously the SPEED - MODE - FUNCTION buttons.

2. From any unit of this network, reset all the network identifiers (SSID) of each unit in the existing network by

pressing the MODE - SPEED - FUNCTION - MODE - SPEED - FUNCTION buttons in sequence and then the

MODE button.

3. Or, if there are units with unknown SSIDs or which are different from the network SSID, set each unit to SLAVE

mode by pressing the MODE - MODE - SPEED - SPEED - FUNCTION - FUNCTION buttons in sequence and

then the SPEED button. Afterwards set the default identification (SSID) on each unit by pressing in sequence

the buttons MODE - MODE - SPEED - SPEED - MODE - MODE and then the SPEED button.

4. If a MASTER unit has not yet been defined, a network unit must be set as MASTER by pressing the MODE -

MODE - SPEED - SPEED - FUNCTION - FUNCTION buttons in sequence and then the MODE key..

5. Finally assign the unique network identification (SSID) from the MASTER unit by pressing the MODE - MODE

- SPEED - SPEED - MODE - MODE buttons in sequence and then the SPEED button.

43

Remote I/O

The connected device can be remotely controlled via clean contacts on remote input 1. If the remote input is active,

the keyboard on the machine is disabled.

• Remote input # 1:

- With input contact 1 closed, all the connected fans work in extraction at maximum speed.

- If 20 seconds since the last key press have not elapsed:

• The white EXTRACTION LED lights up.

• The white 1,2,3,4,5 LEDs light up.

EVEN

ODD

EVEN

ODD

SPEED

BUTTON

MODE

BUTTON

FUNCTION

BUTTON

LED 1

LED 2

LED 3

LED 4

LED

RECOVERY/AUTO NIGHT

LED

INTAKE /AUTO HR%

LED

EXTRAXTION /AUTO COMFORT

LED 5

/ Night

/ Quiet

/ Boost

/ Performance

/ High

Performance

1’÷2’

EVEN ODD

SSID = VOR_2

FLOOR 2

1’÷2’

AB ABAB

1’÷2’

EVEN ODD

SSID = VOR_1

FLOOR 1 RECOVERY MODE

1’÷2’

ABAB

AB

ABB

A

EXAMPLE 1 EXAMPLE 2

ENGLISH

44

La pagina sta caricando ...

Thermex HRW Multicom Guida d'installazione

Thermex HRW Multicom Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti