®
FUSION
®
MS-RA70/MS-RA70N
Installation Instructions
Important Safety Information
WARNING
Failure to follow these warnings and cautions could result in
personal injury, damage to the vessel, or poor product
performance.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
This device must be installed according to these instructions.
Disconnect the vessel's power supply before beginning to install
this product.
Before applying power to this product, make sure it has been
correctly grounded, following the instructions in the guide.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation,
contact FUSION Product Support.
What's In the Box
• DIN mounting plate
• Four 8-gauge, self-tapping screws
• Power and speaker wiring harness
• Auxiliary-in, line-out, and subwoofer-out wiring harness
Tools Needed
• Phillips screwdriver
• Electric drill
• Drill bit (size varies based on surface material and screws
used)
• Rotary cutting tool or jigsaw
• Silicone-based marine sealant (optional)
Mounting Considerations
• The stereo can be mounted on a flat surface or in a single-
DIN opening as a replacement for an existing stereo.
• The stereo must be mounted in a location that allows open
airflow around the rear of the stereo for heat ventilation.
• If you are installing the stereo in a location that may be
exposed to water, it must be mounted within 45 degrees of
the horizontal plane.
•
If you are installing the stereo in a location that may be
exposed to water, the cable should have a drip loop to allow
water to drip down off the cable and avoid damage to the
stereo.
• If you need to mount the stereo outside a boat, it must be
mounted in a location far above the waterline, where it is not
submerged.
• If you need to mount the stereo outside a boat, it should be
mounted in a location where it cannot be damaged by docks,
pilings, or other pieces of equipment.
• To avoid interference with a magnetic compass, the stereo
should be installed at least 15 cm (5.9 in.) away from a
compass.
Mounting the Stereo in a New Location
NOTICE
Be careful when cutting the hole to mount the stereo. There is
only a small amount of clearance between the case and the
mounting holes, and cutting the hole too large could
compromise the stability of the stereo after it is mounted.
Before you can mount the stereo in a new location on the
mounting surface, you must select a location in accordance with
the mounting considerations.
1
Trim the template and make sure it fits at the mounting
location.
2
Adhere the template to the mounting surface.
3
Using a drill bit appropriate for the mounting surface, drill a
hole inside the corner of the dashed line on the template to
prepare the mounting surface for cutting.
4
Using a rotary-cutting tool, cut the mounting surface along
the inside of the dashed line on the template.
5
Place the stereo in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the stereo fits correctly in the cutout, ensure the
mounting holes on the stereo line up with the pilot holes on
the template.
8
If the mounting holes on the stereo do not line up, mark the
new pilot-hole locations.
9
Using an appropriately sized drill bit for the mounting surface
and screw type, drill the pilot holes.
10
Remove the template from the mounting surface.
11
Make the necessary wiring connections (Connection
Considerations, page 2).
12
Place the mounting gasket on the back of the stereo
À
.
July 2018
190-01946-02_0C
13
Place the stereo in the cutout.
14
Secure the stereo to the mounting surface using the included
screws
Á
.
15
Snap the screw covers in place
Â
.
Replacing an Existing Stereo
1
Remove and disconnect the existing stereo.
2
If necessary, remove the existing wiring harness or install a
vehicle- or vessel-specific wiring-harness adapter (not
included) to provide access to the power and speaker wiring.
3
Place the mounting gasket on the back of the stereo
À
.
4
Place the mounting bracket
Á
behind the mounting surface.
5
Make the necessary wiring connections (Connection
Considerations, page 2).
6
Place the stereo in the opening.
7
Secure the stereo to the mounting bracket using the included
screws
Â
.
NOTE: You might need to reach behind the mounting surface
to hold the bracket in place when securing the stereo to the
bracket.
8
Snap the screw covers in place
Ã
.
Connection Considerations
The stereo must be connected to power, to speakers, and to
media input sources to function correctly. You should carefully
plan the layout of the stereo, wired remote, speakers, optional
NMEA 2000
®
network, and your input sources before making
any connections.
Port Identification
Item Description
ANT Connects the stereo to a typical AM/FM antenna using an RF
coaxial connector.
If you are installing the stereo on a boat with a metal hull, you
must use a ground-dependent antenna, and if you are installing
the stereo on a boat with a non-metal hull, you must use a
ground-independent antenna. See the installation instructions
provided with your antenna for more information.
ACC Connects to a FUSION DAB module to receive DAB stations
where available (not included).
NMEA Connects the stereo to a NMEA 2000 network ("N" models
only) (NMEA 2000 System Wiring Diagram, page 4).
USB Connects the stereo to a USB source.
FUSE Contains the fuse for the device.
See the device specifications for replacement fuse information.
À
Connects the stereo to the power and speaker wiring harness.
Á
Connects the stereo to the auxiliary in and line/subwoofer out
wiring harness.
Â
Reserved for future use.
Wiring Harness Wire and Connector Identification
Wire Function Wire Color/
Number
Notes
Power (+) Red (yellow
on some wire
harnesses)
Connects to the positive terminal of
a 12 Vdc power source capable of
supplying 15 A.
Ground (-) Black Connects to the negative terminal of
a 12 Vdc power source capable of
supplying 15 A. This wire should be
connected before connecting the red
(or yellow) wire. All accessories
connected to the stereo must share
a common ground location.
Amplifier on Blue Connects to an optional external
amplifier to turn it on when the
stereo turns on.
2 FUSION MS-RA70/MS-RA70N Installation Instructions
Wire Function Wire Color/
Number
Notes
Mute Brown Activates when connected to
ground.
For example, when connected to a
compatible hands-free mobile kit, the
audio mutes or the input switches to
AUX when a call is received and the
kit connects this wire to ground. This
functionality can be configured from
the settings menu.
Dim Orange Connects to the boat's illumination
wire to dim the stereo screen when
the lights are on.
The gauge of the illumination wire
must be suitable for the fuse
supplying the circuit it is connected
to.
Speaker zone 1
left (+)
White
Speaker zone 1
left (-)
White/black
Speaker zone 1
right (+)
Gray
Speaker zone 1
right (-)
Gray/black
Speaker zone 2
left (+)
Green
Speaker zone 2
left (-)
Green/black
Speaker zone 2
right (+)
Purple
Speaker zone 2
right (-)
Purple/black
Auxiliary in left
Auxiliary in right
À
Provides a red and white RCA
stereo line input for audio sources,
such as a CD or MP3 player.
Zone 1 line out
(left)
Zone 1 line out
(right)
Á
Provides a full-range output to an
external amplifier, and is associated
with the volume control for zone 1.
Zone 2 line out
(left)
Zone 2 line out
(right)
Â
Provides a full-range output to an
external amplifier, and is associated
with the volume control for zone 2.
Subwoofer out
Ã
Each cable provides a single mono
output to a powered subwoofer or
subwoofer amplifier, and one or both
cables can be used, depending on
the connection requirements of the
subwoofer or amplifier.
A connected subwoofer is
associated with the volume control
for zone 1.
Connecting to Power
When connecting the stereo to power, you should connect it
through the ignition or another manual switch.
If it is necessary to extend the power and ground wires, use
14 AWG (2.08 mm
2
) wire. For extensions longer than 1 m (3 ft.),
use 12 AWG (3.31 mm
2
) wire.
1
Route the red power wire
À
to the ignition or another manual
switch
Á
, and route the black ground wire
Â
to the battery.
2
If necessary, route a wire
Ã
between the switch and the
battery .
3
Route the wiring-harness plug to the stereo.
Do not connect the wiring harness to the stereo until after all
of the bare wire connections have been made.
4
Connect the black wire to the negative (-) battery terminal.
5
Connect the red power wire to the ignition or another manual
switch, and connect the switch to the positive (+) battery
terminal if necessary.
6
Connect the wiring harness plug to the stereo.
Speaker Zones
You can group speakers in one area into speaker zones. This
enables you to control the audio level of the zones individually.
For example, you could make the audio quieter in the cabin and
louder on deck.
You can set the balance, volume limit, subwoofer level, and
name for each zone.
Single-Zone System Wiring Example
À
Speakers
Á
Water-tight connection
Complete System Wiring
FUSION MS-RA70/MS-RA70N Installation Instructions 3
Item Description
À
Zone 2 speakers
Á
Water-tight connection
Â
Powered amplifier
Ã
Zone 2 line out
Ä
Amplifier-on signal wire
Å
Zone 1 speakers
Æ
Zone 1 line out
Ç
Zone 1 subwoofer out
Each cable provides a single mono output to a powered
subwoofer or subwoofer amplifier, and one or both cables can be
used, depending on the connection requirements of the
subwoofer or amplifier.
È
Powered subwoofer
NMEA 2000 System Wiring Diagram
NOTE: NMEA 2000 is available on FUSION MS-RA70N models
only.
À
Stereo
Á
Supported chartplotter MFD or compatible FUSION NMEA 2000
remote control
Â
In-line switch
Ã
NMEA 2000 power cable
Ä
NMEA 2000 drop cable from the stereo, up to 6 m (20 ft.)
Å
NMEA 2000 drop cable from the chartplotter MFD or compatible
FUSION NMEA 2000 remote control
Æ
9 to 16 Vdc power supply
Ç
NMEA 2000 terminator or backbone cable
È
NMEA 2000 T-connector
É
NMEA 2000 terminator or backbone cable
Stereo Information
Specifications
General
Weight 556 g (19.6 oz.)
Water resistance IEC 60529 IPX7 (front), IEC 60529 IPX3
(rear)
Operating temperature range From 0 to 50°C (from 32 to 122°F)
Storage temperature range From -20 to 70°C (from -4 to 158°F)
Input voltage From 10.8 to 16 Vdc
Current (max.) 15 A
Current (muted) Less than 900 mA
Current (standby) FUSION MS-RA70: less than 5 mA
FUSION MS-RA70N: less than 15 mA
General
NMEA 2000 LEN 1 (50 mA)
ANT
®
wireless range Up to 3 m (10 ft.)
Compass-safe distance 15 cm (5.9 in.)
On-board, Class AB Amplifier
Output music power per channel 50 W max. x 4 channels at 4 ohm per
channel
Total output music power 200 W max.
Tuner Europe and
Australasia
USA Japan
FM radio
frequency range
87.5 to 108 MHz 87.5 to
107.9 MHz
76 to 95 MHz
FM frequency
step
50 kHz 200 kHz 50 kHz
AM radio
frequency range
522 to 1620 kHz 530 to
1710 kHz
522 to
1620 kHz
AM frequency
step
9 kHz 10 kHz 9 kHz
Stereo Dimension Drawings
Front Dimensions
À
188 mm (7.40 in.)
Á
60 mm (2.36 in.)
Side Dimensions
À
23.5 mm (0.93 in.)
Á
100 mm (3.94 in.)
Â
50 mm (1.97 in.)
Top Dimensions
4 FUSION MS-RA70/MS-RA70N Installation Instructions
À
161 mm (6.34 in.)
Á
23.5 mm (0.93 in.)
Â
12 mm (0.47 in.)
Registering Your FUSION MS-RA70/MS-RA70N
Help us better support you by completing our online registration
today.
• Go to www.fusionentertainment.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Software Updates
For best results, you should update the software in all FUSION
devices at the time of installation to ensure compatibility.
Go to www.fusionentertainment.com/marine to download the
latest software. Software updates and instructions are available
on your device product page.
© 2015–2018 Garmin Ltd. or its subsidiaries
Garmin
®
, the Garmin logo, FUSION
®
, and the Fusion logo are trademarks of Garmin Ltd.
or its subsidiaries, registered in the USA and other countries. These trademarks may not
be used without the express permission of Garmin.
Bluetooth
®
word mark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by Garmin is under license. NMEA
®
, NMEA 2000
®
, and the NMEA 2000 logo
are registered trademarks of the National Marine Electronics Association. Other
trademarks and trade names are those of their respective owners.
A02834 B02834
FUSION MS-RA70/MS-RA70N Installation Instructions 5
www.fusionentertainment.com
TA-2016/3299
-
1
-
2
-
3
-
4
-
5
-
6
Fusion MS-RA70 Guida d'installazione
- Tipo
- Guida d'installazione
- Questo manuale è adatto anche per
in altre lingue
- English: Fusion MS-RA70 Installation guide
Documenti correlati
-
Fusion Fusion Apollo RA770 Guida d'installazione
-
Fusion MS-RA70N Guida d'installazione
-
Fusion MS-UD650 Guida d'installazione
-
-
Fusion Marine Black Box Guida d'installazione
-
Fusion SG-DA61500 Manuale utente
-
Fusion SG-DA82000 Manuale utente
-
Fusion XS-S10CWB Guida d'installazione
-
-
Fusion MS-UD/AV750 Manuale del proprietario