USER MANUAL
DEUTSCH
ENGLISH
NEDERLANDS
FRANCAIS
TABLE OF CONTENTS
Thank you very much for choosing the iiyama LCD monitor.
We recommend that you take a few minutes to read carefully through this brief but
comprehensive manual before installing and switching on the monitor. Please keep this
manual in a safe place for your future reference.
FOR YOUR SAFETY .............................................................................. 1
SAFETY PRECAUTIONS ................................................................. 1
SPECIAL NOTES ON LCD MONITORS ............................................. 3
CUSTOMER SERVICE ...................................................................... 3
CLEANING ....................................................................................... 3
BEFORE YOU OPERATE THE MONITOR ................................................ 4
FEATURES ....................................................................................... 4
CHECKING THE CONTENTS OF THE PACKAGE ............................. 4
CONTROLS AND CONNECTORS .................................................... 5
CONNECTING YOUR MONITOR ...................................................... 6
COMPUTER SETTING ....................................................................... 7
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE .................... 8
PANEL ROTATION ............................................................................ 8
OPERATING THE MONITOR ................................................................... 9
ADJUSTMENT MENU CONTENTS .................................................... 10
SCREEN ADJUSTMENTS ................................................................. 13
POWER MANAGEMENT FEATURE .................................................. 16
TROUBLE SHOOTING ............................................................................ 17
APPENDIX .............................................................................................. 18
SPECIFICATIONS ............................................................................. 18
COMPLIANT TIMING ......................................................................... 19
CONNECTOR PIN ASSIGNMENT ...................................................... 20
SVENSKA
AX3835UT
AX3835UT BK
ITALIANO
ENGLISH
Congratulations!
You have just purchased a TCO’99 approved and labelled
product! Your choice has provided you with a product developed
for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation
of goods and services to the environment. The main problem, as far as computers and other electronics
equipment are concerned, is that environmentally harmful substances are used both in the products and during
their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment,
most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions,
radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously
and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which provides for international and environmental
labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish
Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature
Conservation) and Statens Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric
and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must
be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be
adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO’99 approved and labelled products may also be
obtained via the Internet, using the address: http://www.tco-info.com/
ENGLISH
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to
prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of
flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are
chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing
bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive
damage in fish-eating birds and mammals, due to the bio-accumulative
*
processes. Flame retardants have
been found in human blood and researchers fear that disturbances in foetus development may occur.
The relevant TCO’99 demand requires that plastic components weighing more than 25 grams must not contain
flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit
boards since no substitutes are available.
Cadmium
**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays.
Cadmium damages the nervous system and is toxic in high doses. The relevant TCO’99 requirement states
that batteries, the colour-generating layers of display screens and the electrical or electronics components
must not contain any cadmium.
Mercury
**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic
in high doses. The relevant TCO’99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components associated with the
labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during the manufacture
and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs
break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on
earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.
Lead
**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TCO’99 requirement permits the inclusion of
lead since no replacement has yet been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
ENGLISH
Congratulations!
You have just purchased a TCO’95 approved and labelled
product! Your choice has provided you with a product developed
for professional use. Your purchase has also contributed to
reducing the burden on the environment and also to the further
development of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation
of goods and services to the environment. The main problem, as far as computers and other electronics
equipment are concerned, is that environmentally harmful substances are used both in the products and during
their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment,
most of these potentially damaging substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are important
from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions,
radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously
and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’95 scheme which provides for international and environmental
labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish
Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature
Conservation) and Statens Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric
and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals, brominated and
chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must
be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be
adhered to in each country where the company implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to
reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual ergonomics and good usability.
Below you will find a brief summary of the environmental requirements met by this product. The complete
environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): [email protected]
Current information regarding TCO’95 approved and labelled products may also be obtained via the Internet,
using the address: http://www.tco-info.com/
ENGLISH
Environmental Requirements
Brominated flame retardants
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In
turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of
flame retardant substances. These are related to another group of environmental toxins, PCBs, which are
suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals,
due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers
fear that disturbances in foetus development may occur.
TCO’95 demand requires that plastic components weighing more than 25 grams must not contain
organically bound chlorine and bromine.
Lead
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning.
TCO’95 requirement permits the inclusion of lead since no replacement has yet been developed.*
Cadmium
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
cadmium. The colour-generating layers of display screens must not contain any cadmium.*
Mercury
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and
is toxic in high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of
mercury. It also demands that no mercury is present in any of the electrical or electronics components
concerned with the display unit.*
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded
foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere,
causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer
(malignant melanoma).
The relevant TCO’95 requirement: Neither CFCs nor HCFCs may be used during the manufacturing of
the product or its packaging.
* Bio-accumulative is defined as substances which accumulate within living organisms.
ENGLISH
FCC DECLARATION OF CONFORMITY
Model Number: AX3835UT / AX3835UT BK
Trade Name: iiyama
Responsible party: IIYAMA NORTH AMERICA, INC.
Address: 1560 Brookhollow Drive, Suite 208, Santa Ana, CA 92705 U.S.A.
Telephone number: 714-437-5111
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for Class B Personal Computers and
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a residential environment. This device generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If you determine the device does cause harmful interference to radio
or television reception (this may be determined by monitoring the interference while turning the device off and
on), you are encouraged to try to correct the interference by one of the following measures:
n Reorient or relocate the receiving antenna.
n Increase the separation between the device and receiver.
n Connect the device into an outlet on a circuit different from that to which the receiver
is connected.
n Consult the dealer or an experienced radio or TV technician for help.
To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.
CAUTION Changes or modifications not expressly approved by iiyama could void the users authority
to operate the device under FCC compliance regulations.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterised by their connection to the public low voltage power supply system.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the radio interference regulation of the Canadian department of communications.
CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE
STATEMENT
n We reserve the right to change specifications without notice.
n All trademarks used in this user manual are the property of their respective owners.
n As an ENERGY STAR
®
Partner, iiyama has determined that this product meets the ENERGY STAR
®
guidelines for
energy efficiency.
ENGLISH
FOR YOUR SAFETY
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer or iiyama service center immediately. Further use may be dangerous and
can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
SAFETY PRECAUTIONS
FOR YOUR SAFETY 1
ENGLISH
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For
optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
OTHERS
2 FOR YOUR SAFETY
ENGLISH
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to its correct position.
n
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours.
n
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
n
SPECIAL NOTES ON LCD MONITORS
FOR YOUR SAFETY 3
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
n
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
n
NOTE
The fluorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama
service center.
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
n
n
WARNING
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
n
CAUTION
For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
n
NOTE To protect the LCD panel, do not scratch or rub the screen with a hard object.
n
Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
n
Thinner
Benzine
Abrasive cleaner
Spray-type cleaner
Wax
Acid or Alkaline solvent
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
n
CABINET
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
LCD
SCREEN
Periodic cleaning with a soft dry cloth is recommended.
Don't use tissue paper etc. because these will damage the LCD screen.
CUSTOMER SERVICE
CLEANING
ENGLISH
4 BEFORE YOU OPERATE THE MONITOR
FEATURES
The following accessories are included in your package. Check to see if they are enclosed with the monitor.
If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama office.
n Power Cable* n D-Sub Signal Cable n DVI-D Signal Cable
n USB Cable n User Manual
n Sample: Pivot
®
software (CD)
This software enables to rotate the orientation of the screen to display in portrait or landscape
mode. Consult the user manual for CD-ROM or Engman.rtf in CD-ROM for installation, etc.
CAUTION
* TO USERS IN 120V AREA
The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a
power supply higher than this
rating, then a power cable with a rating of 10A/250V
must be used.
K 38cm (15.0") TFT Color LCD Monitor
K Supports Resolutions up to 1024 × 768
K Super Wide Viewing Angle and High Contrast
K Digital Character Smoothing
K Automatic Set-up
K Plug & Play VESA DDC1/2B Compliant, Windows
®
95/98/2000/Me/XP Compliant
K Power Management (E
NERGY STAR
®
and VESA DPMS Compliant)
K Ergonomic Design
AX3835UT: TCO ’99 and MPR 3 Approved
AX3835UT BK*: TCO ’95 and MPR 3 Approved
*Cabinet color is black.
K Digital Input (DVI-I) for Clear Display
K USB Hub Function
K 90° Panel Rotation Design
K VESA Standard Compliant for Arm or Wall Mounting
CHECKING THE CONTENTS OF THE PACKAGE
Optional parts as below are available for your LCD monitor. Please contact your local iiyama dealer
or regional iiyama office for them. The Speaker is attached to the monitor to output a sound from the
computer or the audio equipment. The Protection Sheet is attached to LCD panel surface to protect
it from stains or scratches.
n Speaker
AX3835UT: OSP1-1 (Bottom, Monoral) AX3835UT BK: OSP1-1B (Bottom, Monoral)
n Protection Sheet (Parts No. 832Z001-03)
BEFORE YOU OPERATE THE MONITOR
The monitor functions as a hub when connected to a USB compliant computer and USB peripherals.
However, with older operating systems and/or BIOS settings in your computer, the USB hub may not
operate. In this case, please contact your computer dealer first for advice.
ENGLISH
CONTROLS AND CONNECTORS
A
Power Indicator
Green: Normal operation
Orange: Power Management
The monitor enters into power management mode which reduces the power
consumption to less than 5W when receiving no horizontal and/or vertical
sync signal.
B
Power Switch
C
Auto Button (Auto Set-up)
Adjust Clock, Phase, H-Position and V-Position automatically.
n The Auto Set-up needs to display the Test.bmp in order for it to work correctly.
(See page 13 for SCREEN ADJUSTMENTS.)
n The screen becomes dark for approximately five seconds during the adjustment.
D
+ / Brightness Button
E
– / Contrast Button
F
Menu Button
G
Input Button
Select either INPUT 1 or 2 for the signal input when both of the signal inputs are connected to a
signal source. Switch INPUT 1 and 2 whenever pressing the Input Button.
The signal input is not selected automatically. Press the Input Button once when the
Power Indicator turns orange irrespective of connecting only one signal input to the
signal source.
H Main Power Switch
I
AC Connector (AC IN)
J
USB-UP
Connect with a USB compliant computer by the USB Cable attached to the monitor.
K
USB-DOWN
Connect any cables from USB compliant peripherals such as mouse, keyboard, etc.
L
D-Sub mini 15pin Connector (INPUT 2)
M
DVI-I 29pin Connector (INPUT 1)
N
Optional Speaker Connector (DC OUT)
<Front> <Back>
NOTE
NOTE
NOTE
BEFORE YOU OPERATE THE MONITOR 5
ENGLISH
6 BEFORE YOU OPERATE THE MONITOR
CONNECTING YOUR MONITOR
[Example of Connection]
A
Ensure that both the computer and the monitor are switched off.
B
Connect the computer to the monitor with the signal cable. (See page 20 for CONNECTOR PIN
ASSIGNMENT.)
C
Connect the monitor to the USB compliant computer with the USB Cable when using the USB hub
features.
D
Connect the Power Cable to the monitor first and then to the power supply.
NOTE n The signal cables used for connecting the computer and monitor vary by the type of computer
used. An incorrect connection may cause serious damage to both the monitor and the
computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector. If a
special cable is required please contact your local iiyama dealer or regional iiyama office.
n For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
n Make sure you tighten the finger screws at each end of the signal cable.
n Cables are connected easily by rotating the panel 90 degrees. (See page 8 for PANEL
ROTATION.)
n Cables can be bundled together inside the cover at the back of the stand. See next page
for cable wiring.
USB Cable (Accessory)
Printer
Keyboard
Mouse
Power Cable (Accessory)
to D-Sub connector
of computer
Computer
to DVI connector
of computer
< Back >
D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable
(Accessory)
ENGLISH
BEFORE YOU OPERATE THE MONITOR 7
[Cable Wiring]
A
Remove the cover at the back of the stand by
sliding it upward.
B
Collect cables at the back of the stand.
C
Replace the cover by inserting the tabs into guide
holes and then sliding the cover downward.
COMPUTER SETTING
n Signal Timing
When you connect the monitor to the computer for the first time, set the signal timing of the
computer to VGA before connection. Change to the desired signal timings listed on page 19 in
COMPLIANT TIMING, after you confirm that the picture appears normally at VGA.
n Windows 95/98/2000/Me/XP Plug & Play
The iiyama LCD monitor complies with DDC1/2B of VESA standard. The Plug & Play function runs
on Windows 95/98/2000/Me/XP by connecting the monitor to DDC1/2B compliant computer with
the Signal Cable supplied. Windows 95/98/2000/Me/XP Monitor Information File for iiyama monitors
may be necessary for your computer and obtained via the Internet, using the address:
http://www.iiyama.com (U.S.A.)
http://www.iiyama.co.uk (U.K.)
NOTE
n For additional information on how to download the driver for your monitor, please
access one of the internet sites noted above.
n Monitor Drivers are not required in most cases for Macintosh or Unix operating systems.
For further information, please contact your computer dealer first for advice.
ENGLISH
ADJUSTING THE HEIGHT AND THE VIEWING ANGLE
8 BEFORE YOU OPERATE THE MONITOR
85mm
35˚
30˚30˚
n For optimal viewing it is recommended to look at
the full face of the monitor, then adjust the monitor’s
height and angle to your own preference.
n Hold the panel so that the monitor does not topple
when you change the monitor’s height or angle.
n You are able to adjust the monitor’s height up to 85
mm, angle up to 30 degrees right and left, 35
degrees upward.
NOTE n Do not touch the LCD screen when you
change the height or the angle. It may
cause damage or break the LCD screen.
n Careful attention is required not to catch
your fingers or hands when you change
the height or the angle.
PANEL ROTATION
A
Adjust the monitor’s height to the maximum.
B
Rotate the panel 90 degrees.
Portrait: Turn clockwise.
Landscape: Turn counter clockwise.
NOTE n Attempting to rotate without fully
extending upward may cause
damage to stand.
n Please use attached Pivot
®
software for rotating the image
on the screen.
C
Adjust the monitor’s angle to your
preference.
90˚
ENGLISH
The On Screen Display disappears several seconds after you stop pressing the buttons while
performing an adjustment. Any changes are automatically saved in the memory when the On
Screen Display
disappears. Turning off the power should be avoided while using the Menu.
n
NOTE
Adjustments for Clock, Phase and Position are saved for each signal timing. Except for these
adjustments, all other adjustments have only one setting which applies to all signal timings.
n
OPERATING THE MONITOR 9
Adjustment icon
Current horizontal frequency,
vertical refresh rate
and resolution
Page no.
800 × 600
Menu:1
H:46.8K V:75.0
OPERATING THE MONITOR
(
Press the Menu Button to start the On Screen Display feature. There are
two Menu pages which can be switched by using the +/– Buttons.
B
Select the Menu page which contains the adjustment icon relating to the
adjustment you want to make. Press the Menu Button again. Then, use the
+/– Buttons to highlight the desired adjustment icon. Press the Menu Button
again.
An adjustment bar appears after you press the Menu Button. Use the +/– Buttons to change the
vertical position settings. The vertical position of the overall display should be changing accordingly
while you are doing this.
C
Use the +/– Buttons to make the appropriate adjustment or setting.
For example, to correct for vertical position, select Menu page number 1 and then press the Menu
Button. Then, select (V-Position) by using the +/– Buttons.
Menu:1
V-Position
V-Position
The bar shows
the progress of the
adjustment being made.
+
–
To create the best picture, your iiyama LCD monitor has been preset at the factory
with the COMPLIANT
TIMING shown on page 19. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 13 for SCREEN ADJUSTMENTS.
ENGLISH
10 OPERATING THE MONITOR
ADJUSTMENT MENU CONTENTS
D-Sub Input
Adjustment Item Problem / Option Button to Press
Too dull
Too intense
Contrast
Brightness*
1
Too dark
Too bright
To correct flickering text or lines
Clock*
2
Phase*
2
H-Position
Too far to the left
Too far to the right
V-Position
Too low
Too high
Return to Menu Highlight “Menu : 1” again.
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
l Contrast: Press the Contrast Button when the Menu is not displayed.
l Brightness: Press the Brightness Button when the Menu is not displayed.
SWITCHING CONTRAST / BRIGHTNESS ADJUSTMENT
To switch between Contrast and Brightness adjustments, press the Menu Button within 10
seconds after pressing the Contrast Button or the Brightness Button during the direct
adjustments above.
To correct flickering text or lines
*
1
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
*
2
See page 13 for SCREEN ADJUSTMENTS.
Direct
Direct
Direct
800 × 600
Menu:1
H:46.8K V:75.0
NOTE
Menu : 1
(D-Sub)
ENGLISH
OPERATING THE MONITOR 11
Adjustment Item
Color Temp.
Auto Balance
Return to Menu.
Adjust the Red, Green and Blue to suitable colors
automatically.
NOTE
n
The screen becomes dark for approximately ten seconds during the adjustment.
n
The Auto Balance needs more than 5 cm around white area in order to work correctly.
The Auto Balance may not work correctly due to your computer system, resolution or
displayed pattern. In this case, select “Reset” and restore factory-preset data.
n
Reddish white
Bluish white
Problem / Option Button to Press
Menu:2
800 × 600
H:46.8K V:75.0
SVENSKA Swedish
Return to Menu
Highlight “Menu : 2” again.
Language
ENGLISH
DEUTSCH
English
German
FRANÇAIS
NEDERLANDS
French
Dutch
Reset
Return to Menu.
Factory-preset data is restored.
OSD Position
You can move the OSD display to any one of the
above 5 positions within the overall display.
Press the + Button to move the OSD in numerical order.
Press the – Button to move the OSD in reverse
numerical order.
Auto Set-up*
1
Return to Menu.
Adjust Clock, Phase, H-Position and V-Position
automatically.
No
Yes
Direct
No
Yes
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
l Auto Set-up: Press the Auto Button.
Direct
No
Yes
*
1
See page 13 for SCREEN ADJUSTMENTS.
Menu : 2
(D-Sub)
ENGLISH
12 OPERATING THE MONITOR
*
1
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
DVI Input
Adjustment Item Problem / Option Button to Press
Too dull
Too intense
Contrast
Brightness*
1
Too dark
Too bright
Direct
Direct
Color Temp.
Reddish white
Bluish white
OSD Position
You can move the OSD display to any one of the
above 5 positions within the overall display.
Press the + Button to move the OSD in numerical
order.
Press the – Button to move the OSD in reverse
numerical order.
SVENSKA Swedish
Language
ENGLISH
DEUTSCH
English
German
FRANÇAIS
NEDERLANDS
French
Dutch
Reset
Return to Menu.
Factory-preset data is restored.
No
Yes
800 × 600
Menu
H:46.8K V:75.0
You can skip the Menu pages and display an adjustment scale directly by using the
following button operations.
l Contrast: Press the Contrast Button when the Menu is not displayed.
l Brightness: Press the Brightness Button when the Menu is not displayed.
SWITCHING CONTRAST / BRIGHTNESS ADJUSTMENT
To switch between Contrast and Brightness adjustments, press the Menu Button within 10
seconds after pressing the Contrast Button or the Brightness Button during the direct
adjustments above.
Direct
NOTE
ENGLISH
n The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use. They are unlike the adjustments you would make
on a CRT monitor.
n The monitor is designed to provide the best performance at resolution of 1024 × 768, but can not
provide the best at resolutions of less than 1024 × 768 because the picture is automatically stretched
to fit the full screen. It is recommended to operate at resolution of 1024 × 768 in normal use.
n Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
n It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
n Perform adjustments after a warm-up period of at least thirty minutes.
n Additional adjustments may be required after the Auto Set-up depending on the resolution or signal
timing.
n The Auto Set-up may not work correctly when displaying the picture other than the Test.bmp
(screen adjustment pattern). In this case, manual adjustments are required.
SCREEN ADJUSTMENTS
Adjust the image by following the procedure below to get the desired picture when selecting D-Sub input.
OPERATING THE MONITOR 13
There are two ways to adjust the screen. One way is automatic adjustment for Clock, Phase and
Position. Another way is performing each adjustment manually.
Perform the Auto Set-up first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Set-up, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the iiyama web site (http://
www.iiyama.com or http://www.iiyama.co.uk).
This manual explains adjustment under Windows 95/98/2000/Me/XP.
A
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE n Consult the appropriate documentation for doing this.
n Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the
wallpaper setting dialogue box surely. If you use Microsoft
®
PLUS! 95/98 cancel the
setting of “Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Zebra pattern
This is the image displayed at 1024 × 768.
Color bar
Picture frame
ENGLISH
14 OPERATING THE MONITOR
+
–
+
–
+
–
B
Press the Auto Button. (Direct adjustment)
Or perform the Auto Set-up.
C
Adjust the image manually by following procedure below when the screen has a
flicker or blur, or the picture does not fit in the display area after performing the Auto
Set-up.
D
Adjust the V-Position so that the top and bottom of the picture frame will fit to the
display area.
E
1) Adjust the H-Position so that the left side of the picture frame will move to the left
edge of the display area.
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Clock.
NOTE n When the left side of the picture frame moves apart from the left edge of the display
area during the Clock adjustment, adjust steps 1) and 2).
n Another way to make the Clock adjustment is to correct the vertical wavy lines in the
zebra pattern.
n The picture may flicker during the Clock, H-Position and V-Position adjustment.
NOTE n In case that you have to make adjustments at resolutions of less than 1024 × 768,
adjust the vertical position of the screen adjustment pattern to center.
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
in altre lingue
- français: iiyama AX3835UTBK Manuel utilisateur
- Deutsch: iiyama AX3835UTBK Benutzerhandbuch
- Nederlands: iiyama AX3835UTBK Handleiding
Documenti correlati
Altri documenti
-
NEC MultiSync® LCD1525MBK Manuale del proprietario
-
Sony SDM-X95F Manuale utente
-
Sony SDM-S53 Istruzioni per l'uso
-
Sony SDM-S204E Manuale utente
-
Lenovo T560 Manuale utente
-
-
-
Sharp LL-T2010W Istruzioni per l'uso
-
Logic Controls LE1000, LE1015, LE1017, LE2000 Manuale utente
-
Vision Techsplitter Manuale del proprietario