Lenovo T560 Manuale utente

ENGLISH

English

ii

First Edition (August / 2001)

This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information

herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or

program(s) at any time.

It is possible that this publication may contain reference to, or information about, IBM products (machines and programs),

programming, or services that are not announced in your country.

Requests for copies of this publication and for technical information about IBM products should be made to your IBM Authorized

Dealer or IBM Retailer.

No part of this publication may be reproduced or distributed in any form or by any means without prior permission in writing from

the International Business Machines Corporation.

Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to

restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

Notices

References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all

countries in which IBM operates. Any reference to an IBM product, program or service is not intended to state or imply that only

IBM¡¯s product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe

any of IBM¡¯s intellectual property rights or other legally protectable rights may be used instead of the IBM product, program, or

service. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly

designated by IBM, are the user¡¯s responsibility.

IBM may have patents or pending patent applications covering subject matter in this document. The furnishing of this document

does not give you any license to these patents.

Trademarks

The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States, other

countries, or both:

HelpCenter IBM

ENERGY STAR is a U.S. Govt. registered trademark.

Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in the United States, other countries, or both.

Other company, product, and service names may be trademarks or service marks of others.

ENGLISH

1

Setup............................................................................................................................2

Hardware Requirements......................................................................................2

Desktop Use ........................................................................................................2

VESA Mount Use.................................................................................................2

Handling Instructions ...........................................................................................2

Monitor Installation ....................................................................................................3

Connecting your Monitor......................................................................................3

Switching on your Monitor....................................................................................3

Monitor Driver Installation.........................................................................................4

Driver installation for Windows95 or Windows98.................................................4

Driver installation for Windows 2000 or Windows Me.................................................5

Image Setup for Analog Input ..................................................................................6

Auto Setup...........................................................................................................6

Auto Setup for Windows3.1, 95 or Windows2000, Windows Me or Windows NT

.........

7

Image Setup for DOS...........................................................................................9

Manual Image Setup ..................................................................................................10

Ergonomic Considerations......................................................................................11

Workplace preparation.......................................................................................11

Working Practices ..............................................................................................11

Adjusting the Monitor Position ...............................................................................12

VESA wall mounting ..........................................................................................13

Pivot® software..................................................................................................13

Caring for your Monitor......................................................................................13

Adjusting Your LCD Monitor ...................................................................................14

User controls......................................................................................................14

On-screen display (OSD) controls.....................................................................16

Further Information ..................................................................................................19

Display modes ...................................................................................................19

Power Management...........................................................................................20

VESA Wall Mounting ................................................................................................21

Troubleshooting .......................................................................................................22

Further Help.......................................................................................................24

Specifications ...........................................................................................................25

Warranty ....................................................................................................................28

Compliances ...............................................................................see at rear of manual

Service Information....................................................................see at rear of manual

Contents

2

Hardware Requirements

This monitor requires a computer with a suitable on-board sub-system or

Video Adapter card that can support XGA 1024 x 768, SVGA 800 x 600, or

VGA 640 x 480 at 60Hz.

Setup

Do not support the monitor

within the screen area. The

Liquid Crystal Display is glass

and can be damaged by rough

handling or excessive

pressure.

Handling InstructionsHandling Instructions

DESKTOP USE

- REMOVE CLIP

VESA MOUNT USE

- Do Not Remove Clip

1. Lift the monitor by placing both hands under the lower part of the cover.

2. Before using your monitor for the first time, remove the clear protective

film from the front of the screen.

3

2

1

2

1

3

1. Turn off your computer and all attached devices.

2.

Connect the signal cable.

The AC adapter and the analog signal cable are already connected to your

monitor

When connecting the analog

signal cable (

Figure A)

Connect free end of the attached signal cable to the Dsub connector on the computer

and tighten the screws.

When connecting the DVI signal cable

(Figure B)

Connect one end of the monitor signal cable to the DVI connector on the rear panel of

the monitor. Connect the other end to the DVI port on the rear panel of the computer

and tighten the screws.

3. Connect the power cord to the power adapter and then plug the power

cord into a properly grounded outlet.

1. Switch on the power source to your monitor.

2. Switch on your monitor by pushing and releasing the power switch

marked [ ].

[To switch off your monitor, push and release the power switch again.]

3. Switch on your computer.

4. Run AUTO SETUP by following the instructions in the Auto Setup

section on page 6.

Connecting your Monitor

Switching on your Monitor

(Figure A)

(Figure B)

Monitor Installation

ENGLISH

4

To use the Plug and Play feature in Microsoft

®

Windows

®

95 or Windows

98, files should be loaded from the IBM Monitor Installation diskette.

1. Turn off the computer and all attached devices.

2. Ensure that the monitor is connected correctly.

3. Turn on the monitor and then the system unit. Allow the system to boot

into Windows95 or Windows98.

Your computer’s Plug and Play code may warn you that your system

hardware has changed. This means that it has detected your new

monitor for the first time.

4. Open the

DISPLAY PROPERTIES window by clicking START, SETTINGS,

CONTROL PANEL and then double - clicking on the DISPLAY icon.

5. Click the SETTINGS tab.

• In case of Windows 95 :

6 -

1. Click the CHANGE DISPLAY TYPE button.

2.Click the CHANGE MONITOR TYPE button.

• In case of Windows 98 :

6 -

1.Click the

ADVANCED button.

2.Click the MONITOR tab.

3. Open the UPGRADE DEVICE DRIVER WIZARD window by clicking on

CHANGE button and then select the NEXT button.

4. Click the “Display a list of the known drivers for this device so that

I can choose a specific driver” and then select the NEXT button.

7. Insert the Setup diskette into the diskette driver: and click the

HAVE DISK

button.

8. Click OK.

9. Encure that the floppy disk drive letter is selected.

10.Choose IBM T560 monitor and Click OK. The files will be copied from

the diskette to your hard disk drive.

11.Close all open windows and remove the diskette.

12.Restart the system.

The system will automatically select the maximum refresh rate and

corresponding Color Matching Profiles.

Monitor Driver Installation

Driver installation for Windows 95 or Windows 98

This section must be

completed before

continuing with the

Windows95 or Windows98

Auto Setup on page 7.

i

On LCD monitors, unlike

CRTs, a faster refresh rate

does not improve display

quality. IBM recommends

using either 1024 x 768 at a

refresh rate of 60Hz or 640 x

480 at a refresh rate of 60Hz.

ENGLISH

5

To use the Plug and Play feature in Microsoft Windows 2000 or Microsoft

Windows Millennium Edition(Me) files should be loaded from the IBM

Monitor Installation diskette.

1. Turn off the computer and all attached devices.

2. Ensure that the monitor is connected correctly.

3. Turn on the monitor and then the system unit. Allow the system to boot

into Windows 2000 or Windows Me.

4. Open the DISPLAY PROPERTIES window by clicking START, SETTINGS,

CONTROL PANEL and then double-clicking the DISPLAY icon.

5. Click the

SETTINGS tab.

6. Click the ADVANCED button.

7. Click the

MONITOR tab.

8. Click the PROPERTIES button.

9. Click the

DRIVER tab.

10.Open the

UPGRADE DEVICE DRIVER WIZARD window by clicking on UPDATE

DRIVER and then Click the NEXT button.

11.Select the “Display a list of the known drivers for this device so that I can

choose a specific driver” and then Click the NEXT button.

12.Insert the Setup diskette into the diskette drive : and click the

HAVE DISK

button.

13.Click OK.

14.Ensure that the floppy disk drive letter is selected.

15.Choose IBM T560 monitor and Click OK. The files will be copied from

the diskette to your hard disk drive.

16.Close all open windows and remove the diskette.

17.Reboot the system.

The system will automatically select the maximum refresh rate and

corresponding Color Matching Profiles.

Driver Installation for Windows 2000 or Windows Me

This section must be

completed before

continuing with the

Windows2000 ,Windows Me

Auto Setup on page 7.

i

On LCD monitors, unlike

CRTs, a faster refresh rate

does not improve display

quality. IBM recommends

using either 1024 x 768 at a

refresh rate of 60Hz or 640 x

480 at a refresh rate of 60Hz.

6

For digital input, setup is not required.

When you first use your monitor you must perform Auto Setup. This procedure

set up your monitor to process the video signals from your computer without

image discoloration or smearing. After you perform Auto Setup, the settings are

stored and used each time you turn on the monitor.

In order to optimise the displayed image a set-up utility is provided on the

IBM Monitor Installation Diskette. Operation of this utility is dependent on the

operating system on your computer. You may choose to run AUTO SETUP for

each operating system that you use. This means that if you sometimes use

your monitor while running any version of Windows and sometimes also use it

from within DOS (not a DOS window), you must run AUTO SETUP for both

Windows and DOS. You may run versions of AUTO SETUP in any order.

Before you begin AUTO SETUP for your computer:

1. Make a backup copy of the setup diskettes supplied with the monitor.

2. Make sure the computer video mode is set in the range of the

supported screen resolution shown in the table on page18.

You should perform AUTO SETUP for each screen mode you use.

Image Setup for analog input

Auto Setup

Before carrying out this

section, it is very important

that the correct monitor

drivers have been

installed.(See pages 4 and 5)

i

The Setup Utility included

on the setup diskette

displays a test pattern of dots.

It does not replace or modify

the display drivers.

i

The Auto Setup

instructions require the

monitor to be warmed up for 15

minutes. This is not required

for normal operation.

i

If your computer does not

run with the setup

diskettes shipped with the

monitor, refer to Manual Setup

on page 10

i

The AUTO SETUP process

only applies to the current

screen mode. When a new

mode is selected, repeat this

section to reset the monitor.

ENGLISH

7

1. Turn on the monitor first; then the computer.

If the message CHECK SIGNAL CABLE is displayed, or if nothing is

displayed check:

• that the video interface cable is not connected properly.

• the correct video adapter card is not installed.

2. Wait approximately 15 minutes, until the monitor warms up.

3. Ensure that the icon bar and tool bar, if displayed are at the bottom of

the screen.

4. Insert the diskette labelled ‘IBM Monitor Installation Disk’ into the

diskette drive.

5. Check the operating system installed on your computer and follow the

instructions from the table below.

6. When the test pattern appears, press the OSD Enter button at the

bottom of the monitor to display the initial OSD menu.

7. Use an Arrow button ( or ), to select the IMAGE SET-UP icon

and press the OSD Enter button to access the function.

8. Using an Arrow button ( or ), select AUTO and press the OSD

Enter button . This activates the AUTO SETUP procedure, which will

optimize the display settings with the provided test pattern. The image

may be affected during this procedure and you may notice small

changes to the test pattern.

To abort the AUTO SETUP function, press the ESC key.

9. When finished, the OSD main menu returns. Press the Exit button

once to exit from the OSD.

i

If the monitor is in standby

mode (STANDBY ON), it

may automatically turn off while

you are waiting for it to warm up.

i

The size and diversity of the

dot pattern varies with the

screen resolution.

i

Position the mouse pointer

at the bottom center of the

screen. This allows AUTO

SETUP to run properly

Step1

Open

PROGRAM

Manager

Select

START

Select RUN

Select

RUN

Type

‘A:\TESTPAT’

and press

ENTER

Step2 Step3

Windows 3.1

Windows 95

Windows 98

Windows 2000

Microsoft Windows NT®4.0

Windows Me

Operating

System

Auto Setup for Windows 3.1, 95 or Windows 2000, Windows®Me or

Windows NT

8

10. Press the ESC key on your keyboard to return to Windows.

You have completed the monitor setup for Windows. If you use other operat-

ing systems, perform the appropriate AUTO SETUP for those systems, also: see

Image Setup for DOS on page 9.

9

1. Turn on the monitor first; then the computer.

If the message CHECK SIGNAL CABLE is displayed, or if nothing is

displayed check:

• that the video interface cable is not connected properly.

• the correct video adapter card is not installed.

2. Wait approximately 15 minutes, until the monitor warms up.

3. Insert the diskette labelled ‘IBM Monitor Installation Disk’ into the

diskette drive.

4. Display the command prompt screen of the DOS full-screen display.

5. At the command prompt, type ‘A:’ and press ENTER.

6. Type ‘TESTPATD’ and press ENTER.

7. Select from the screen the number for the color or text mode you want

to setup.

8. Select from the screen the number for the video mode you want to

setup.

You may repeat this process for as many of the color and video modes

as you need.

9. When the dot pattern appears, press the OSD Enter button at the

bottom of the monitor to display the initial OSD menu.

10. Use an Arrow button ( or ), to select the IMAGE SET-UP icon

and press the OSD Enter button to access the function.

11. Using an Arrow button ( or ), select AUTO and press the OSD

Enter button . This activates the AUTO SETUP procedure, which will

optimize the display settings with the provided dot patterns.

The image may be affected during this procedure and you may notice

small changes to the test pattern.

12. When finished, the OSD main menu returns.

Press the Exit button to exit from the OSD.

13. Press the ESCAPE key to exit the test pattern program.

14. Type ‘Exit’ at the command prompt to return to Windows.

If you use other operating systems, perform the appropriate Image Setup

for those systems, also: see

Image Setup Windows 3.1, Windows 95, Windows 98, Windows 2000,

Windows Me or Windows NT® 4.0 workstation on page 7.

Image Setup for DOS

i

If the monitor is in standby

mode (STANDBY ON), it

may automatically turn off while

you are waiting for it to warm

up. If this happens, switch off

the monitor and switch it on

again after a few seconds.

i

If you are using PC-DOS/V,

change to U.S. mode by

typing ‘CHEV US’ and pressing

ENTER at the command

prompt.

You must use when you run

DOS Auto Setup.

i

The size and diversity of

the dot pattern varies with

the screen resolution.

i

If the screen flickers,

repeat the setup several

times until the flicker is

minimised, or adjust it manually

by following refer to

Manual Setup on page 10.

ENGLISH

10

Normally, you can complete the setup procedure using Image S

ETUP,

however, if your screen image is still distorted after you perform Image SETUP

or the setup diskette does not run on your system, perform MANUAL SETUP.

1. Have your monitor turned on for about 15 minutes, until the monitor

warms up.

2. Display the image you most frequently use on the screen.

3. Press the OSD Enter button at the botton of the monitor to display

the initial OSD menu.

4. Use an Arrow button ( or ) to select the IMAGE SET-UP icon

and press the OSD Enter button to access the function.

5. Using an Arrow button ( or ), select MANUAL, press and then

press once to select COARSE. Left and right arrow adjustment

indicators become illuminated (see page17).

6. Use the Arrow buttons to manually adjust to correct (as much as

possible) for for jitter or noise in the image, then press to save the

changes.

7. Use an Arrow button to select FINE and press the button.

8. Use the Arrow buttons again to tune the image to your liking.

9. When finished, press the Exit button four times to exit from the

OSD.

You have completed the monitor setup.

Manual Image Setup

i

If the monitor is in standby

mode (STANDBY ON), it

might automatically turn off

while you are waiting for it to

warm up.

ENGLISH

11

i

This section gives advice

on how you can work

comfortably and reduce

fatigue.

Rest

Take regular breaks. Vary your posture, stand up and stretch occasionally

as prolonged use of computer workstations can be tiring.

Back

Sit back in your chair and use the backrest.

Hands

Use a light touch on the keyboard, keeping your hands and fingers relaxed.

Allow a space in front of the keyboard to rest your wrists when not typing.

Consider using a wristpad.

Eyesight

Working with monitors, in common with any prolonged close work, can be

visually demanding. Look away from the screen periodically and have your

eyesight checked regularly.

Screen settings

Set the screen brightness and contrast to a comfortable level. You may

have to adjust this as the lighting changes during the day. Many application

programs let you select color combinations which can help you to view in

comfort. See the User controls section on page 14 for more information.

Working Practices

i

This section gives advice

on what you should

consider before you set up

your monitor.

Workplace Preparation

Height

Position the monitor directly the top of the screen is slightly below your eye

level when you sit at your workstation.

Orientation

- Choose a position that gives the least reflection from lights and windows,

usually at a right angle to any windows.

- Positon the monitor directly in front of you so that you do not have to twist

your body to use it.

- Tilt the monitor to a comfortable viewing angle.

Ergonomic Considerations

12

Tilt Range :-37 ~145

You can tilt the screen backward and forward as shown below(Figure A).

Height Range

You can adjust height of the screen(Figure B).

Landscape & Portrait

This monitor offers the ability to rotate between landscape and portrait

modes(Figure C). The monitor rotates from Landscape to Portrait through

90°clockwise and from Portrait to Landscape through 90°anti-clockwise.

i

With the IBM Flat Panel

Monitor, you can adjust

its position in various ways

for maximum comfort.

Adjusting the Monitor Position

(Figure A)

-37

+145

(Figure B)

Maximum:

4.87 inch(123.8 mm)

(Figure C)

ENGLISH

13

Be sure to turn off the power before you perform any maintenance on the

monitor. Clean your monitor as follows:

• Gently wipe the covers and the screen with a soft cloth.

• Remove finger marks and grease with a damp cloth and mild detergent.

• Never use flammable cleaning materials to clean your IBM monitor or

any other electrical apparatus.

Pivot software has been provided with your new monitor.

This allows the image to be rotated through either 90˚, allowing the image

to be viewed in landscape or portrait mode, see Figure C. Or rotated

through 180˚, allowing a person opposite the user to view the image when

tilted fully backwards in a landscape orientation, see Figure A. Or rotated

through 270˚, allowing a person opposite the user to view the image when

tilted fully backwards in a portrait orientation.

Caring for your Monitor

Pivot Software

VESA wall mounting (See page 21 for the details)

14

Adjusting Your LCD Monitor

User controls

User control features

Icon Direct Access Functions

i

The image is already

optimized for many display

modes, however the user

controls can be used to adjust

the image to your liking.

i

The settings are saved

after adjustment and

when exiting the OSD and

will be effective thereafter.

Switches the monitors on and off

Bring up Contrast adjustment

Bring up Brightness adjustment

Lock controls when held for 10 seconds

switch between input signals.

Icon Monitor controls

and

Display main OSD menu and selects highligted menu item.

Moved the cursor to highlight icons or make adjustments.

Exits from current OSD menu.

ENGLISH

15

CONTROLS LOCK / UNLOCK

This feature allows you to secure the current control settings, while allowing

the user to adjust Brightness or Contrast, so that they cannot be

inadvertently changed. Push and hold the enter button[ ] for 10 seconds;

the message “Controls Locked” appears.

You can unlock the OSD controls at any time by pushing the enter button[ ]

for 10 seconds; the message “Controls Unlocked” will appear.

16

The settings adjustable with the user controls are viewed through the On -

Screen Display (OSD). Press the enter button [ ] to display the main OSD

menu.

Initial appearance of OSD

main menu;

On-screen display (OSD) controls

i

The LCD monitor needs

time to become thermally

stable the first time you turn it

on each day. Thus, to achieve

more accurate adjustments for

parameters, allow the LCD

monitor to warm up (be On) for

at least 15 minutes before

making any screen adjustment.

MAIN MENU

Digital Input

BRIGHTNESS

MAIN MENU

Analog Input

BRIGHTNESS

75

OSD functions

OSD Icon Description

sub-menu(s)

Auto

If AUTO is selected the

image will automatically

adjust

Control and

Adjustments

Adjusts brightness

Adjusts contrast

The IMAGE SET-UP function is used

to adjust the level of noise in the video

signal which causes horizontal lines or

areas on the screen where the image

appears to be unstable and jitters or

shimmers. This can be done

automatically or manually.

It is not availible when the digital

input

BRIGHTNESS

CONTRAST

IMAGE SET-UP

sub menu;

When the Analog Signal input

When the Digital Signal input

ENGLISH

17

OSD Icon

Select the Color Mode you find most

comfortable and then fine tune the

colors using the User Color Mode

menu, if necessary.

Description Sub-menu(s)

Manual SET-

UP

• Fine

• Coarse

Preset 1

(Warm White)

Preset 2

(Normal White)

Preset 3

(Cool White)

Increases or decreases

redness

Increases or decreases

greenness

Increases or decreases

blueness

COLOR MODE

USER COLOR

MODE-

•

Red

•

Green

•

Blue

To adjust the focus of the

display. This item allows

you to remove any

horizontal noise and clear

or sharpen the image of

characters.

Fine adjustments should

be can done after

adjusting the Coarse .

If manual is selected, the user will go

to the manual adjustment screen.

Controls and

Adjustments

Changes the position of the OSD on the

screen.

OSD Position

H-POSITION

V-POSITION

COLOR

IMAGE SET-UP

CONT

18

OSD Icon

Sub-menu(S)

• YES

• NO

Controls and

Adjustments

Description

RESET

OSD SIZE

Language

To select OSD size

The language chosen affects only the language of the OSD.

Select one of the five language to use for the OSD.

It has no effect on any software running on the computer.

• ENGLISH

• FRANCAIS

• DEUTSCH

• ITALIANO

• ESPANOL

• SMALL

• MID

• BIG

• INFORMATION

• PRESET MODES

• USER MODES

Use the and

buttons to move between

information screens.

Information

Display model name, serial number, year of manufacture

and microcode level.

Display all preset modes stored in the monitor.

Display all user modes stored in the monitor.

The current display mode will be shown at the base of all

information screens.

OSD time

To select OSD display duration time.

(5 - 60 seconds)

H-POSITION

V-POSITION

Reset should return all available functions

(apart from language which should not

change unless adjusted via the

LANGUAGE menu) fo their factory

presets.

Moves the screen left and right .

Is not availible with a digital input

Moves the screen up and down.

Is not availible with a digital input

La pagina sta caricando ...

Lenovo T560 Manuale utente

Lenovo T560 Manuale utente

in altre lingue

Documenti correlati

Altri documenti