ZENOAH KOMATSU BC2001 Manuale utente

Categoria
Tagliaerba
Tipo
Manuale utente

Questo manuale è adatto anche per

BC2001
TR2000
GB
GB
F
D
I
E
F
D
I
E
T3338-93110 (209)
OPERATOR’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’ISTRUZIONI
MANUAL DE INSTRUCCIONES
BRUSHCUTTERS
DEBROUSSAILLEUSE
FREISCHNEIDER
DECESPUGLIATORE
DESBROZADOR
English
Français Deutsch
Italiano
Español
ATENCION!!!
RIESGO DE DAÑO AUDITIVO
EN NORMALES CONDICIONES DE UTILIZACIÓN, ESTA MAQUINA PUEDE
TOLERAR, PARA EL OPERADOR ENCARGADO, UN NIVEL DE EXPOSICÍON
DIARIO A RUIDO EQUIVALENTE O SUPERIOR A
85 dB(A)
WARNING!!!
RISK OF DAMAGING HEARING
IN NORMAL CONDITIONS OF USE, THIS MACHINE
MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE
FOR THE OPERATOR EQUAL TO OR GREATER THAN
85 dB(A)
ATTENTION!!!
DANGER D'ATTEINTE A L'OUIE
L'OPERATEUR UTILISANT NORMALEMENT CETTE MACHINE
PEUTS S'EXPOSER QUOTIDIENNEMENT
A UN BRUIT EGAL OU DEPASSANT
85 dB(A)
ACHTUNG!!!
HÖRSCHADEN - RISIKO
UNTER NORMALEN ANWENDUNGSBEDIGUNGEN
KANN DIESES GERÄT DIE BEDIENUNGSPERSON
EINEM TÄGLICHEN GERÄUSCHPEGEL VON
85 dB(A)
ODER MEHR AUSSETZEN
ATTENZIONE!!!
RISCHIO DI DANNO UDITIVO
NELLE NORMALI CONDIZIONI DI UTILIZZO, QUESTA MACCHINA PUÒ
COMPORTARE PER L'OPERATORE ADDETTO, UN LIVELLO DI ESPOSIZIONE
PERSONALE E GIORNALIERO A RUMORE PARI O SUPERIORE A
85 dB(A)
MODEL SOUND LEVEL VIBRATION LEVEL
MODELE NIVEAU SONORE NIVEAU DE VIBRATION
MODELLE KLANGPEGEL VIBRATIONSPEGEL
MODELLO LIVELLO DEL SUONO LIVELLO DI VIBRAZIONE
MODELO NIVEL DE SONIDO NIVEL DE VIBRACION
EN27917 ISO 10884 ISO 7916
LwA
guaranteed
22.5 cm
3
96.6dB(A) 108dB(A) 2.7m/s
2
3.9m/s
2
LpA idling racing
English Français
SAFETY FIRST
Instructions contained in warnings
within this manual marked with a
symbol concern critical points which
must be taken into consideration to
prevent possible serious bodily injury,
and for this reason you are requested
to read all such instructions carefully
and follow them without fail.
WARNINGS IN THE MANUAL
This mark indicates instructions which
must be followed in order to prevent
accidents which could lead to serious
bodily injury or death.
This mark indicates instructions which
must be followed, or it leads to mechanical
failure, breakdown, or damage.
This mark indicates hints or directions
useful in the use of the product.
NOTE
IMPORTANT
WARNING
SECURITE
Les instructions contenues dans les
mises en garde de ce mode d’emploi
portant le symbole concernent les
points critiques qui doivent être pris en
considération pour éviter les blessures
corporelles graves, c’est pourquoi ces
précautions doivent être
rigoureusement suivies.
DIFFERENTS TYPES
D’AVERTISSEMENT DE CE MODE
D’EMPLOI
Les instructions repérées par ce symbole
doivent être rigoureusement suivies afin
d’éviter tout accident pouvant entraîner
des blessures corporelles graves ou la
mort.
Les instructions repérées par ce symbole
doivent être suivies afin d’éviter tout
incident mécanique, panne ou
endommagement de la débroussailleuse.
Remarques utilisées dans des instructions
ou conseils supplémentaires pour
l’utilisation de cette débroussailleuse.
REMARQUE
IMPORTANT
AVERTISSEMENT
Contents Tables des matieres
6
1. Parts location...............................................8
2. Specifications ............................................10
3. Warning labels on the machine................12
4. Symbols on the machine ..........................12
5. For safe operation .....................................14
6. Set up..........................................................26
7. Fuel .............................................................28
8. Operation....................................................32
9. Maintenance...............................................38
10. Storage .......................................................46
11. Troubleshooting guide..............................48
1. Emplacement des pieces............................8
2. Fiche technique ........................................10
3.
Etiquettes d’avertissement sur la machine
.......12
4. Symboles utilises sur la machine............12
5. Consignes de securite ..............................14
6. Assemblage ...............................................26
7. Carburant ...................................................28
8. Fonctionnement.........................................32
9. Entretien.....................................................38
10. Rangement.................................................46
11.
Guide de localisation des pannes
.................48
EspañolDeutsch Italiano
SICHERHEIT HAT VORRANG
Die Hinweise in den Warnungen dieser
Anleitung bzw. auf den mit einem -
Symbol gekennzeichneten
Warnplaketten sind von größter
Bedeutung für die Betriebssicherheit.
Deshalb sollten Sie diese Warnungen
sorgfältig durchlesen und strikt
beachten, um das Risiko von schweren
Verletzungen zu vermeiden.
WARNHINWEISE IN DER
ANLEITUNG
Dieses Symbol bedeutet, daß diese
Instruktionen befolgt werden müssen,
damit Unfälle mit folgenschweren
Verletzungen, die u.a. zum Tode führen
können, vermieden werden.
Dieses Symbol bedeutet, daß diese
Instruktionen befolgt werden müssen oder
es kommt zu mechanischen Defekten,
Versagen des Gerätes oder Schäden.
Dieses Symbol zeigt Tips oder Ratschläge
für den Gerätebetrieb an.
HINWEIS
WICHTIG
WARNUNG
LA SICUREZZA INNANZI TUTTO
Le istruzioni contenute nelle sezioni di
avvertimento precedute dal simbolo
riguardano dei punti critici che
devono essere osservate per prevenire
potenziali lesioni personali gravi. Per
questo motivo, dovete leggere tutte
queste istruzioni attentamente ed
osservarne il contenuto in ogni
momento.
SEGNALAZIONI USATE NEL
MANUALE
Questo marchio rappresenta delle
istruzioni che devono essere osservate
per prevenire eventuali incidenti che
possono causare lesioni gravi o addirittura
mortali.
Questo marchio indica delle istruzioni che
devono essere seguite per evitare
malfunzionamenti meccanici, guasti o
danni.
Questo marchio indica dei suggerimenti o
indicazioni utili per l’utilizzo del prodotto.
NOTA
IMPORTANTE
AVVERTIMENTO
LA SEGURIDAD PRIMERO
Las instrucciones que aparecen en
este manual bajo las advertencias
marcadas con el símbolo hacen
referencia a puntos críticos que deben
tomarse en consideración para evitar
posibles lesiones físicas; por esta
razón, le solicitamos que lea
detenidamente todas estas
instrucciones y que las siga
estrictamente.
ADVERTENCIAS CONTENIDAS EN
EL MANUAL
Bajo este símbolo aparecen instrucciones
que se deben seguir a fin de evitar
accidentes que pueden causar serias
lesiones físicas o la muerte.
Bajo este símbolo aparecen instrucciones
importantes que se deben seguir; ignorar
estas instrucciones puede ocasionar fallos
mecánicos, desperfectos o daños.
Este símbolo hace referencia a consejos o
indicaciones que son de utilidad para el
uso del producto.
NOTA
IMPORTANTE
ADVERTENCIA
Inhalt ContenidoIndice
7
1. Ubicazione dei componenti........................9
2. Dati tecnici .................................................11
3.
Etichetta di avvertimento sull’apparecchio
.......13
4. Simboli sulla macchina.............................13
5. Per un funzionamento sicuro...................15
6. Impostazione..............................................27
7. Carburante .................................................29
8. Funzionamento..........................................33
9. Manutenzione.............................................39
10. Immagazzinaggio.......................................47
11. Localizzazione dei guasti..........................49
1. Situación de las piezas ...............................9
2. Especificaciohes .......................................11
3.
Etiqueta de advertencia en la máquina
..........13
4.
Símbolos presentes en la máquina
...............13
5. Instrucciones de seguridad......................15
6. Montaje.......................................................27
7. Combustible...............................................29
8. Uso..............................................................33
9. Mantenimiento ...........................................39
10. Almacenamiento........................................47
11. Guía de localización y solución de
problemas ..................................................49
1. Anordnung der bauteile..............................9
2. Technische daten ......................................11
3. Warnaufkleber auf der Maschine .............13
4. Symbole auf der maschine.......................13
5. Sicherer betrieb .........................................15
6. Zusammenbau ...........................................27
7. Kraftstoff ....................................................29
8. Betrieb ........................................................33
9. Wartung......................................................39
10. Lagerung ....................................................47
11. Fehlersuche ...............................................49
English Français
1. Parts location 1. Emplacement des pieces
8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
[BC2001]
[TR2000]
(1) Primer pump
(2) Air cleaner cover
(3) Choke lever
(4) Fuel tank
(5) Starter knob
(6) Line head
(7) Gear case
(8) Debris guard
(9) Loop handle
(10) Drive shaft housing
(11) Sholder strap hanger
(12) Throttle lever
(13) Ignition switch
(14) Throttle cable
(1) Pompe d’amorçage
(2) Capot du filtre à air
(3) Levier de starter
(4) Réservoir de carburant
(5) Poignée de démarrage
(6) Tete de coupe a fil
(7) Boîtier du renvoi d’angle
(8) Cache de protection
(9) Poignée
(10) Tube de l’arbre d’entraînement
(11) Fixation du harnais
(12) Levier d’accélération
(13) Bouton d’allumage
(14) Câble d’accélérateur
EspañolDeutsch Italiano
1. Anordnung der bauteile 1. Ubicazione dei componenti 1. Situación de las piezas
9
(1) Anlaßeinspritzpumpe
(2) Luftfilterabdeckung
(3) Chokehebel
(4) Kraftstofftank
(5) Startknopf
(6) Schnurkopfes
(7) Winkelgetriebe
(8) Abfallschutz
(9) Schleifengriff
(10) Antriebswelle
(11) Schultergurtklammer
(12) Drosselklappenhebel
(13) Zündschalter
(14) Drosselklappenkabel
(1) Pompa del cicchetto
(2) Coperchio del filtro dell’aria
(3) Leva del dispositivo di
avviamento a freddo
(4) Serbatoio del carburante
(5)
Manopola del motorino di avviamento
(6) Strumento da taglio a corda
(7) Scatola degli ingranaggi
(8) Protezione contro i detriti
(9) Maniglia ergonomica
(10) Albero motore
(11) Occhiello per tracolla
(12) Leva del gas
(13) Interruttore di accensione
(14) Cavo del gas
(1) Cebador
(2) Cubierta del filtro de aire
(3) Palanca del estrangulador
(4) Tanque de combustible
(5) Arrancador
(6) Cabezal de línea
(7) Caja de engranajes
(8) Protector contra desechos
(9) Mango
(10) Eje de accionamiento
(11) Colgador de correa para hombro
(12) Palanca del acelerador
(13) Interruptor de encendido
(14) Cable del acelerador
English
2. Specifications
10
Français
2. Fiche technique
BC2001/TR2000
Overall size (L x W x H) ················································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm
Dry weight ····················································································································································································· 4.1 / 4.7 kg
Engine Type ··················································································································································· Air-cooled 2-stroke gasoline
Model······································································································································································ Zenoah G20LS
Displacement ····································································································································································· 21.7cm
3
Fuel ···················································································································································· Mixture (Gasoline 25 : Oil 1)
Carburetor ····························································································································································· Diaphragm type
Ignition system········································································································································································ C.D.I
Spark plug ································································································································································NGK BPMR7A
Fuel tank capacity ···················································································································································································0.5
Starter ························································································································································································ Recoil starter
Clutch····················································································································································································· Centrifugal type
Reduction ratio······················································································································································································· 1.462
Cutting head rotating direction·················································································································· Counter-clockwise(Operator view)
Specifications are subject to change without notice.
BC2001/TR2000
Dimensions totales (L x L x H)······································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm
Poids à vide····················································································································································································4,1 / 4,7 kg
Moteur Type ·········································································································································· 2 temps à essence refroidi par air
Modèle···································································································································································· Zenoah G20LS
Cylindrée············································································································································································21,7 cm
3
Carburant······································································································································· Mélange (essence 25 : huile 1)
Carburateur ····················································································································································· Typa à Diaphragme
Système d’allumage ······························································································································································· C.D.I
Bougie d’allumage··················································································································································· NGK BPMR7A
Contenance du réservoir de carburant··················································································································································· 0,5
Starter··················································································································································································· Starter à détente
Embrayage············································································································································································· Type centrifuge
Rapport de réduction·············································································································································································· 1,462
Sens de rotation de la tête de coupe············································································································ Anti-horaire (vue de l’opérateur)
Ces spécifications peuvent être modifiées sans préavis.
Deutsch
11
2. Technische Daten
Italiano
2. Dati tecnici
Español
2. Especificaciohes
BC2001/TR2000
Tamaño global (Long x Anch x Alt)································································································ 1795 x 230 x 303 / 1795 x 340 x 303 mm
Peso en seco················································································································································································ 4,1 / 4,7 kg.
Motor Tipo··························································································································· Refrigerado por aire / gasolina de 2 tiempos
Modelo ··································································································································································· Zenoah G20LS
Desplazamiento ································································································································································ 21,7 cm
3
Combustible ································································································································· Mezcla (Gasolina 25: Aceite 1)
Carburador ····························································································································································· Tipo diafragma
Sistema de encendido ···························································································································································· C.D.I
Bujía ······································································································································································· NGK BPMR7A
Capacidad del depósito de combustible ················································································································································ 0,5
Arrancador······························································································································································· De cuerda con retroceso
Embrague················································································································································································ Tipo centrífugo
Relación de reducción·············································································································································································1,462
Dirección de rotación de cabeza cortador················································· Sentido contrario a las agujas del reloj (vista desde el operador)
Especificaciones sujetas a cambios sin previo aviso.
BC2001/TR2000
Abmessungen (L x B x H)·············································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm
Trockengewicht ············································································································································································· 4,1 / 4,7 kg
MotorTyp ···································································································································· luftgekühlter 2-Takt-Benzinmotor
Modell····································································································································································· Zenoah G20LS
Hubraum ··········································································································································································· 21,7 cm
3
Kraftstoff ······································································································································ Gemisch(Benzin 25, Öl 1 Anteil)
Vergaser ····································································································································································· Membrantyp
Zündsystem ············································································································································································ C.D.I
Zündkerze ······························································································································································· NGK BPMR7A
Tankkapazität························································································································································································· 0,5
Starter ····················································································································································································· Rückzugstarter
Kupplung············································································································································································ Fliehkraftkupplung
Untersetzungsverhältnis········································································································································································· 1,462
Schneidekopf-Drehrichtung·················································································································· gegen Uhrzeigersinn (vom Bediener)
Technischen Daten können ohne Vorankündigung geändert werden.
BC2001/TR2000
Dimensioni (L x P x H) ··················································································································· 1795 x 230 x 303 / 1795 x 340 x 303 mm
Peso a vuoto ················································································································································································· 4,1 / 4,7 kg
Motore Tipo ········································································································· Motore a benzina a 2 tempi con raffreddamento ad aria
Modello··································································································································································· Zenoah G20LS
Cilindrata··········································································································································································· 21,7 cm
3
Carburante ·········································································································································· Miscela (benzina 25/ olio 1)
Carburatore···························································································································································· Tipo diaframma
Sistema di accensione···························································································································································· C.D.I
Candela··································································································································································· NGK BPMR7A
Capacità del serbatoio del carburante·················································································································································· 0,5 litri
Avviamento············································································································································································ Starter a rinculo
Frizione················································································································································································· Tipo centrifugale
Rapporto di riduzione············································································································································································· 1,462
Direzione di rotazione della testa di taglio····················································································· Nel senso antiorario (visto dall’operatore)
Le specifiche sono soggette a modifiche senza preavviso.
English Français
3. Warning labels on the
machine
3. Etiquettes d’avertissement
sur la machine
12
(1) Read owner's manual before
operating this machine.
(2) Wear head, eye and ear protection.
(3) Warning/Attention
(4) Keep all children, bystanders and
helpers 15 meters away from the
brushcutter
If warning labels peel off or become soiled
and impossible to read, you should
contact the dealer from which you
purchased the product to order new labels
and affix them in the required location(s).
Never remodel your brushcutter.
We won't warrant the machine, if you use
the remodeled brushcutter or you don't
observe the proper usage written in the
manual.
WARNING
IMPORTANT
(1) Lire le mode d’emploi avant
d’utiliser cette machine.
(2) Porter un casque de sécurité, des
lunettes de sécurité et un casque
antibruit.
(3) Avertissement/Attention
(4) Interdire aux enfants ou à toute
personne de s’approcher dans un
rayon de 15 mètres de la
débroussailleuse.
Si les étiquettes d’avertissement se
décollent, deviennent sales ou impossible
à lire, commander de nouvelles étiquettes
auprès du revendeur pour les remplacer.
Ne pas modifier la débroussailleuse.
La garantie sera annulée si la
débroussailleuse a été modifiée ou
utilisée de manière non conforme aux
instructions de ce mode d’emploi.
AVERTISSEMENT
IMPORTANT
4. Symbols on the machine
4. Symboles utilises sur la
machine
For safe operation and maintenance,
symbols are carved in relief on the
machine. According to these indications,
please be careful not to take a mistake.
(a) The port to refuel the "MIX GASOLINE"
Position:
FUEL TANK CAP
(b) The direction to close the choke
Position:
AIR CLEANER COVER
(c) The direction to open the choke
Position:
AIR CLEANER COVER
Des symboles en relief ont été placés sur
la machine pour assurer la sécurité à
l’usage et faciliter l’entretien. Prendre soin
d’observer les indications suivantes afin
d’éviter les erreurs.
(a) Emplacement de remplissage du
“MELANGE”
Emplacement:
BOUCHON DU RESERVOIR DE
CARBURANT
(b) Position fermée du starter
Emplacement:
CAPOT DU FILTRE A AIR
(c) Position ouverte du starter
Emplacement:
CAPOT DU FILTRE A AIR
EspañolDeutsch Italiano
3. Warnaufkleber auf der
Maschine
3. Etichetta di avvertimento
sull’apparecchio
3. Etiqueta de advertencia en
la máquina
13
(1) Vor dem Betrieb dieser Maschine,
die Bedienungsanleitung lesen.
(2) Kopf-, Augen und Ohrenschutz
tragen.
(3) Warnung/Achtung
(4) Kinder, Zuschauer und Helfer 15
Meter vom Freischneider entfernt
halten.
Wenn Warnplaketten sich lösen oder
schmutzig und nicht mehr lesbar sind,
verständigen Sie Ihren Händler bei dem
Sie das Produkt gekauft haben, um neue
Plaketten zu bestellen und diese an den
erforderlichen Positionen zu befestigen.
Ihren Freischneider niemals
modifizieren.
Die Garantie erlischt, wenn Sie einen
modifizierten Freischneider verwenden
oder Sie nicht den in der
Bedienungsanleitung beschriebenen
Betrieb beachten.
WARNUNG
WICHTIG
(1) Leggete il manuale d’istruzioni
prima di usare questa macchina.
(2) Indossate il casco, gli occhiali di
protezione e le cuffie.
(3) Avvertimento/Attenzione
(4) Tenete i bambini, eventuali
spettatori ed aiutanti ad una
distanza di 15 metri dal
decespugliatore.
Se un’etichetta di avvertimento si stacca o
si sporca e diventa così illeggibile,
contattate il rivenditore presso il quale
avete acquistato il prodotto per ordinare
delle nuove etichette. Poi fissate le nuove
etichette negli appositi luoghi.
Non modificate mai il decespugliatore.
Se modificate il decespugliatore
oppure non seguite le istruzioni fornite
in questo manuale, la garanzia sarà
nulla.
IMPORTANTE
(1) Lea el manual de instrucciones
antes de usar esta máquina.
(2) Use protección para la cabeza, ojos
y oídos.
(3) Advertencia/Atención
(4) Mantenga a niños, espectadores y
ayudantes a una distancia de 15
metros del desbrozador.
Si las etiquetas de advertencia se
desprenden o se manchan y se vuelven
ilegibles, contacte al distribuidor donde
adquirió el producto y solicite nuevas
etiquetas. Fije las nuevas etiquetas en las
posiciones correspondientes.
Nunca haga ningún tipo de
modificación al desbrozador.
No podemos garantizar la máquina si
usted utiliza el desbrozador
remodelado o si no sigue las
instrucciones de uso contenidas en
este manual.
ADVERTENCIA
IMPORTANTE
4. Symbole auf der Maschine 4. Simboli sulla macchina
4. Símbolos presentes en la
máquina
Für einen sicheren Betrieb und eine
sichere Wartung sind Symbole als
Hilfestellung auf die Maschine eingeprägt.
Gehen Sie gemäß diesen Anzeigen
vorsichtig vor und machen Sie keinen
Fehler.
(a) Die Öffnung zum Nachfüllen des
“BENZINGEMISCHS”
Position:
KRAFTSTOFFTANKDECKEL
(b) Die Richtung zum Schließen der
Drossel
Position:
LUFTFILTERABDECKUNG
(c) Die Richtung zum Öffnen der Drossel
Position:
LUFTFILTERABDECKUNG
Per un funzionamento e una
manutenzione sicura, i simboli sono stati
incisi in rilievo sull’apparecchio. Seguite
queste indicazioni per evitare eventuali
errori.
(a) Porta per riempire la miscela “MIX
GASOLINE”,
Posizione:
COPERCHIO DEL SERBATOIO DEL
CARBURANTE.
(b) Direzione di chiusura dell’aria
Posizione:
COPERCHIO DEL FILTRO DELL’ARIA
(c) Direzione di apertura dell’aria
Posizione:
COPERCHIO DEL FILTRO DELL’ARIA
Para el uso y mantenimiento seguro del
producto, los símbolos han sido
estampados en relieve en la máquina.
Siga siempre estas indicaciones, y tenga
cuidado de no cometer un error.
(a) Orificio de llenado de “MEZCLA DE
GASOLINA”
Posición:
TAPÓN DEL TANQUE DE
COMBUSTIBLE
(b) Dirección de cierre del estrangulador
Posición:
CUBIERTA DEL FILTRO DE AIRE
(c) Dirección de apertura del
estrangulador
Posición:
CUBIERTA DEL FILTRO DE AIRE
English Français
5. For safe operation
14
1. Read this manual carefully until you
completely understand and follow all
safety and operating instructions.
2. Keep this manual handy so that you
may refer to it later whenever any
questions arise. Also note, if you have
any questions which cannot be
answered herein, contact the dealer
from whom you purchased the
product.
3. Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this
product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual to use
the machine.
WORKING CONDITION
1. When using the product, you should
wear proper clothing and protective
equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools and files
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area
(rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jewelry,
short trousers, sandals, or go barefoot.
Do not wear anything which might be
caught by a moving part of the unit.
Secure hair so it is above shoulder
length.
WORKING CIRCUMSTANCE
1. Never start the engine inside a closed
room or building. Exhaust gases
contain dangerous carbon monoxide.
2. Never use the product:
a. when the ground is slippery or when
you can’t maintain a steady posture.
b. At night, at times of heavy fog, or at
any other times when your field of
vision might be limited and it would
1. Lire ce manuel attentivement jusqu’à
une compréhension totale et suivre
toutes les instructions de sécurité et
d’utilisation.
2. Conserver ce mode d’emploi à portée
de la main pour le consulter au
moindre doute. Si une question reste
sans réponse, contacter le revendeur.
3. Ne pas oublier de donner le manuel
avec la machine en cas de revente ou
de prêt.
4. Ne pas laisser des enfants ou toute
personne incapable de comprendre
les instructions, utiliser cette machine.
CONDITIONS DE TRAVAIL
1. Lors de l’utilisation de cette machine, il
est nécessaire de porter des vêtements
appropriés et des équipements de
sécurité.
(1) Casque
(2) Casque antibruit
(3) Lunettes ou masque de protection
(4) Gants de travail épais
(5) Chaussures de sécurité à semelle
antidérapante
2. Les objets suivants doivent être
emportés sur le lieu de travail :
(1) Les outils fournis avec la machine et
des limes
(2) Une réserve de carburant
(3) Une lame de rechange
(4) Matériel pour délimiter la zone de
travail
(5) Un sifflet (pour collaborateur ou en
cas d’urgence)
(6) Une hache ou une scie (pour
enlever les obstacles)
3. Ne pas porter des vêtements lâches, de
short, de bijou, de sandales ou travailler
pieds nus. Ne pas porter quoi que ce
soit pouvant être happé par les pièces
en mouvement de la machine. Porter
les cheveux longs noués au-dessus des
épaules.
CONDITIONS DE TRAVAIL
1. Ne jamais mettre la machine en marche
à l’intérieur d’une pièce ou d’un
bâtiment. Les gaz d’échappement
contiennent du monoxide de carbone
dangereux.
2. Ne jamais utiliser la machine dans les
conditions suivantes:
a. Lorsque le sol est glissant ou lorsqu’il
est impossible de se maintenir dans
5. Consignes de securite
EspañolDeutsch Italiano
15
1. Lesen Sie sich diese Anleitung
sorgfältig durch, bis Sie alle
Sicherheits- und Bedienungshinweise
verstehen und befolgen.
2. Diese Anleitung greifbereit haben, um
sie im Zweifelsfall schnell zur Hand zu
haben. Bei Fragen zum Gerät, die
nicht in dieser Anleitung behandelt
werden, bitte an den Händler wenden,
der Ihnen das Produkt verkauft hat.
3. Bei Verkauf, Verleih oder Weitergabe
stets diese Anleitung zusammen mit
dem Gerät übergeben.
4. Niemals Kinder oder Personen, die
die Anweisungen in dieser Anleitung
nicht vollständig verstehen, die
Maschine betreiben lassen.
ARBEITSBEDINGUNG
1. Wenn das Produkt benutzt wird, sollten
Sie stets richtige Kleidung und
Schutzausrüstung tragen.
(1) Helm
(2) Ohrenschutz
(3) Schutzbrille oder Schutzmaske
(4) Dicke Schutzhandschuhe
(5) Rutschfeste Arbeitsschuhe
2. Und Sie sollten folgende Dinge bei sich
tragen.
(1) Mitgelieferte Werkzeuge und Feilen
(2) Reservekraftstoff
(3) Ersatzschneidblatt
(4) Gegenstände, die Ihren
Arbeitsbereich kennzeichnen (Seil,
Warnzeichen)
(5) Pfeife (für Zusammenarbeit oder
Notfall)
(6) Beil oder Säge (zum Entfernen von
Hindernissen)
3. Keine lockere Kleidung, Schmuck,
kurze Hosen oder Sandalen tragen und
nicht barfuß gehen. Nichts tragen, daß
von den beweglichen Teilen des
Gerätes erfaßt werden kann. Haare
über Schulterhöhe zusammenbinden.
ARBEITSUMSTAND
1. Den Motor niemals in geschlossenen
Räumen oder Gebäuden starten.
Abgase enthalten gefährliches
Kohlenmonoxid.
2. Niemals das Produkt benutzen:
a. wenn der Untergrund glitschig ist
oder ein stabiler Stand beeinträchtigt
ist.
b. Nachts, bei dichtem Nebel oder
1. Leggete questo manuale
attentamente per capire
completamente ed osservare tutte le
norme di sicurezza ed istruzioni per
l’uso.
2. Tenete questo manuale in un luogo
accessibile per poter fare riferimento
all stesso in un momento successivo,
in caso di dubbi. Inoltre, se avete
delle domande alle quali non trovate
la risposta nel manuale, rivolgetevi al
vostro rivenditore da cui avete
acquistato questo prodotto.
3. Assicuratevi di allegare questo
manuale se vendete o prestate l’unità
oppure se la stessa cambia
proprietario in altri modi.
4. Non lasciate mai che bambini o
persone non consapevoli delle
istruzioni fornite nel manuale
d’istruzioni utilizzino l’apparecchio.
CONDIZIONI LAVORATIVE
1. Quando usate il prodotto, dovete
indossare i vestiti e le protezioni
appropriate.
(1) Casco
(2) Cuffie di protezione
(3) Occhiali di protezione o visiera
(4) Spessi guanti di lavoro
(5) Scarponi di lavoro con la suola
antiscivolo
2. Inoltre, portate i seguenti oggetti con
voi:
(1) Gli utensili e le lime in dotazione
(2) Il carburante custodito in modo
appropriato
(3) Una lama di riserva
(4) Oggetti per delimitare l’area di
lavoro (una corda, delle insegne di
avvertimento)
(5) Un fischietto (per collaborazione o
per situazioni di emergenza)
(6) Accetta o sega (per rimuovere degli
ostacoli)
3. Non indossate dei vestiti lenti, gioielli,
pantaloncini, sandali, né camminate
scalzo. Non indossate nessun oggetto
che possa rimanere inceppato nelle
parti mobili dell’unità. Legate i capelli in
modo tale che sia al di sopra
dell’altezza delle spalle.
CIRCOSTANZE LAVORATIVE
1. Non accendete mai il motore all’interno
di una stanza chiusa o in un edificio. I
gasi di scarico contengono il monossido
di carbonio che è molto pericoloso.
2. Non usate mai il prodotto nelle seguenti
situazioni:
a. Quando il terreno è scivoloso o
quando non potete mantenere una
posizione stabile.
1. Lea detenidamente este manual
hasta comprender cabalmente todas
las instrucciones de seguridad y uso.
2. Mantenga este manual a mano para
que pueda consultarlo cuando tenga
alguna duda. Si tiene cualquier duda
que no esté cubierta en este manual,
consulte en la tienda donde adquirió
el producto.
3. Asegúrese de incluir siempre este
manual al vender, prestar o transferir
la propiedad de este producto.
4. Nunca permita que niños u otras
personas que no sean capaces de
comprender cabalmente las
instrucciones que se dan en el
manual utilicen la máquina.
CONDICIONES DE TRABAJO
1. Al utilizar el producto, asegúrese de
usar la vestimenta y el equipo de
protección adecuados.
(1) Casco
(2) Protectores para los oídos
(3) Gafas protectoras o protector facial
(4) Guantes de trabajo gruesos
(5) Botas de trabajo con suela
antideslizante
2 Asegúrese de llevar con usted los
siguientes elementos:
(1) Herramientas y limas incluidas
(2) Combustible de reserva
(3) Hoja de repuesto
(4) Elementos para marcar su área de
trabajo (cuerdas, letreros de
advertencia)
(5) Silbato (para colaboración o
situaciones de emergencia)
(6) Hacha pequeña o sierra (para quitar
obstáculos)
3. No use ropa suelta, joyas, pantalones
cortos ni sandalias, y no trabaje
descalzo. No use nada que pueda ser
atrapado por las piezas móviles de la
unidad. Recójase el pelo,
asegurándose de que quede por
encima de sus hombros.
PRECAUCIONES
1. Nunca arranque el motor dentro de una
habitación cerrada o edificio. Los gases
de escape contienen monóxido de
carbono peligroso.
2. Nunca use el producto en los siguientes
casos:
a. Cuando el suelo sea resbaloso o
cuando usted no pueda mantener
una posición estable.
5. Sicherer Betrieb
5. Per un funzionamento sicuro
5. Instrucciones de seguridad
English Français
16
be difficult to gain a clear view of the
working area.
c. During rain storms, during lightning
storms, at times of strong or gale-
force winds, or at any other times
when weather conditions might make
it unsafe to use the product.
WORKING PLAN
1. You should never use the product when
under the influence of alcohol, when
suffering from exhaustion or lack of
sleep, when suffering from drowsiness
as a result of having taken cold
medicine or at any other time when a
possibility exists that your judgment
might be impaired or that you might not
be able to operate the product properly
and in a safe manner.
2. When planning your work schedule,
allow plenty of time to rest. Limit the
amount of time over which the product
is to be used continuously to
somewhere around 30–40 minutes per
session, and take 10–20 minutes of rest
between work sessions. Also try to
keep the total amount of work
performed in a single day under 2 hours
or less.
1. If you don’t observe the working
time, or working manner (See
USING THE PRODUCT), Repetitive
Stress Injury(RSI) could occur.
If you feel discomfort, redness and
swelling of your fingers or any other
part of your body, see a doctor
before getting worse.
2. To avoid noise complaints, in
general, operate product between
8a.m. and 5p.m. on weekdays and
9a.m. to 5p.m. weekends.
Check and follow the local regulations as
to sound level and hours of operations for
the product.
BEFORE STARTING THE ENGINE
1. The area within a perimeter of 15 m of
the person using the product should be
considered a hazardous area into which
no one should enter. If necessary
yellow warning rope, warning signs
should be placed around the perimeter
of the area. When work is to be
NOTE
WARNING
une position correcte.
b. La nuit, par temps de brouillard ou
lorsque la visibilité ou le champ de
vision empêche de voir clairement la
zone de travail.
c. Pendant les averses, les orages
avec éclairs, par grands vents ou
toute autre condition climatique
rendant l’utilisation de la machine
dangereuse.
PLAN DE TRAVAIL
1. Ne jamais utiliser la machine sous
l’influence de l’alcool ou en état de
faiblesse due à la fatigue, au manque
de sommeil, à la prise de médicament
ou à tout autre moment où l’on n’est
pas réellement capable de l’utiliser
correctement et en toute sécurité.
2. Lors de l’élaboration du plan de travail,
prévoir suffisamment de temps de
repos. Limiter la durée des périodes
pendant lesquelles la machine est
utilisée sans interruption entre 30 et 40
minutes. Se reposer de 10 à 20 minutes
entre ces périodes. Autant que
possible, essayer de limiter ce genre de
travail à 2 heures par jour.
1. Si ce plan de travail et cette méthode
de travail ne sont pas respectés, un
accident dû au stress répétitif peut
se produire (voir UTILISATION DE
LA MACHINE).
Si l’on ressent un malaise ou si les
doigts ou tout autre membre
rougissent et enflent, consulter un
docteur avant que cela ne s’aggrave.
2. Pour éviter les problèmes de bruit
avec le voisinage, utiliser
généralement la machine entre 8 et
17 heures pendant la semaine et de 9
à 17 heures les fins de semaine.
Vérifier et suivre la réglementation locale
sur le niveau de bruit et les horaires
d’utilisation de ce type de machine.
AVANT DE METTRE LE MOTEUR EN
MARCHE
1. La zone dans un rayon de 15 mètres
autour de l’opérateur est considérée
comme dangereuse et personne ne doit
s’y trouver. Si nécessaire, délimiter le
périmètre de la zone de travail avec du
ruban de marquage (rouge fluorescent
REMARQUE
AVERTISSEMENT
5. For safe operation 5. Consignes de securite
EspañolDeutsch Italiano
17
anderen Bedingungen, die die Sicht
im Arbeits- und Sicherheitsbereich
einschränken und einen sicheren
Betrieb verhindern.
c. Bei starkem Niederschlag, Gewitter,
stürmischem Wind oder anderen
Wetterbedingungen, die einen
sicheren Einsatz dieses Produktes
unmöglich machen.
ARBEITSPLAN
1. Sie sollten das Produkt keinesfalls unter
Einfluß von Alkohol, bei Erschöpfung
oder Übermüdung, bei Schläfrigkeit
aufgrund der Einnahme von
Erkältungsmitteln oder dann benutzen,
wenn die Möglichkeit besteht, daß Ihr
Urteilsvermögen beeinträchtigt ist oder
Sie nicht imstande sind, das Produkt
einwandfrei und sicher zu bedienen.
2. Beim Planen der Arbeitseinsätze,
genügend Ruhephasen
berücksichtigen. Begrenzen Sie die
Zeitdauer, die die vorgesehenen 30 –
40 Minuten pro Arbeitseinsatz bei
kontinuierlichem Betrieb überschreitet
und zwischen den Einsätzen jeweils
Pausen von 10 – 20 Minuten einlegen.
Die gesamte Arbeitszeit sollte täglich
unter 2 Stunden oder weniger liegen.
1. Wenn Sie die Arbeitszeit oder die
Arbeitsweise nicht beachten (Siehe
ANWENDUNG DES PRODUKTS),
könnten Verletzungen aufgrund sich
wiederholenden Stresses (RSI)
verursacht werden.
Wenn Sie sich nicht wohl fühlen,
wenn Ihre Finger oder ein anderes
Körperteil rot und angeschwollen ist,
suchen Sie einen Arzt auf, bevor es
schlimmer wird.
2. Um Lärmbelästigung zu verhindern
sollte das Gerät im allgemeinen
werktags zwischen 8.00 und 17.00
und am Wochenende zwischen 9.00
und 17.00 Uhr verwendet werden.
Prüfen und befolgen Sie die örtlichen
Bestimmungen für dieses Produkt und die
Betriebsstunden.
VOR DEM START DES MOTORS
1. Der Gefahrenbereich während des
Betriebs, aus dem Dritte unbedingt
fernzuhalten sind, erstreckt sich in
einem Umkreis von 15 Metern, um
dieses Produkt. Falls erforderlich, den
Arbeitsbereich mit einem gelben
Warnband, mit Warnzeichen absperren.
HINWEIS
WARNUNG
b. Di notte, quando c’è molta nebbia o
in altre occasioni quando il campo
visivo è limitato ed è difficile avere
una visione nitida dell’area di lavoro.
c. Durante la pioggia, durante una
tempesta, quando tira un vento molto
forte o in altre occasioni in cui le
condizioni meteorologiche rendono
poco sicuro l’utilizzo del prodotto.
PIANO DI LAVORO
1. Non usate mai il prodotto sotto
l’influenza dell’alcool, se siete stanchi o
assonnati; se siete in uno stato di
sonnolenza per via dell’assunzione di
farmaci o in altre occasioni in cui vostro
giudizio può essere ridotto,
impedendovi così di usare il prodotto in
modo corretto e sicuro.
2. Quando pianificate il lavoro, non
dimenticate di fornire del tempo per
riposare. Limitate il tempo di utilizzo del
prodotto a 30 — 40 minuti per sessione
e riposatevi da 10 a 20 minuti tra le
sessioni di lavoro. Inoltre, cercate di
mantenere la quantità totale del lavoro
effettuato durante la giornata a 2 ore o
meno.
1. Se non osservate il tempo di lavoro o
il modo di lavoro. (Fate riferimento
alla sezione UTILIZZO DEL
PRODOTTO), si possono verificare
delle lesioni per via di sforzi continui
(RSI). Se sentite del disagio, oppure
se le dita od altre parti del corpo si
arrossiscono o si gonfiano,
consultate un medico prima che la
situazione peggiora.
2. Per evitare dei problemi dovuti alla
generazione di rumore, usate il
prodotto tra le ore 8 antimeridiane e
le ore 5 pomeridiane nei giorni feriali
e dalle ore 9 antimeridiane e le 5
pomeridiane nei giorni festivi.
Controllate ed osservate le norme locali
sul livello sonoro e sulle ore operative del
prodotto.
PRIMA DI ACCENDERE IL MOTORE
1. L’area all’interno di un perimetro di 15
m dalla persona usando il prodotto va
considerata una zona pericolosa in cui
nessuno deve entrare. Se necessario,
posizionare una corda di avvertimento
di colore giallo oppure delle insegna di
avvertimento intorno all’area. Quando il
NOTA
AVVERTIMENTO
b. Durante la noche, cuando haya
niebla densa, o en cualquier otra
situación en que su campo de visión
esté limitado y sea difícil lograr una
adecuada visión del área de trabajo.
c. Durante tormentas de lluvia,
tormentas eléctricas, tormentas de
viento, o en cualquier otra
circunstancia en que las condiciones
climáticas puedan hacer inseguro el
uso del producto.
PLAN DE TRABAJO
1. Nunca utilice el producto cuando se
encuentre bajo la influencia del alcohol,
cuando sufra de fatiga o falta de sueño,
cuando sienta somnolencia debido a
que ha tomado una medicina para el
resfrío, o en cualquier otra situación
que pueda afectar su juicio y usted no
sea capaz de utilizar el producto
correctamente y de manera segura.
2. Al planificar su trabajo, deje un tiempo
suficiente para descansar. Limite el
tiempo de uso continuo del producto a
30–40 minutos por sesión, y tome
descansos de 10–20 minutos entre las
sesiones de trabajo. Asimismo, trate de
que la cantidad total de trabajo diario
sea inferior a 2 horas.
1. Si no sigue las recomendaciones en
cuanto a la duración del trabajo o a
la forma de trabajar (consulte USO
DEL PRODUCTO), usted podrá sufrir
una lesión por esfuerzo repetido
(RSI).
Si siente algún malestar, si sus
dedos o cualquier otra parte de su
cuerpo enrojecen o se hinchan,
consulte oportunamente a un
médico.
2. Para evitar problemas de ruido, en
general utilice el producto entre las 8
a.m. y las 5 p.m. los días laborables,
y de 9 a.m. a 5 p.m. durante el fin de
semana.
Compruebe y respete las disposiciones
locales respecto de los niveles de ruido y
horas de uso del producto.
ANTES DE ARRANCAR EL MOTOR
1. El área dentro de un perímetro de 15 m
de la persona que está usando el
producto debe considerarse como un
área de peligro en la que nadie debe
ingresar. Si fuera necesario, marque el
perímetro del área de trabajo con una
cuerda de color amarillo y letreros de
NOTA
ADVERTENCIA
5. Sicherer Betrieb
5. Per un funzionamento sicuro
5. Instrucciones de seguridad
English Français
18
performed simultaneously by two or
more persons, care should also be
taken to constantly look around or
otherwise check for the presence and
locations of other people working so as
to maintain a distance between each
person sufficient to ensure safety.
2. Check the condition of working area to
avoid any accident by hitting hidden
obstacles such as stumps, stones,
cans, or broken grass.
Remove any obstacle before beginning
work.
3. Inspect the entire unit for loose
fasteners and fuel leakage. Make sure
that the cutting attachment is properly
installed and securely fastened.
4. Be sure the debris guard is firmly
attached in place.
5. Always use the shoulder strap. Adjust
the strap for comfort before starting the
engine. The strap should be adjusted
so the left hand can comfortably hold
the handlebar grip approximately waist
high.
STARTING THE ENGINE
1. Keep bystanders and animals at least
15 m away from the operating point. If
you are approached, immediately stop
the engine.
2. The product is equipped with a
centrifugal clutch mechanism, so the
cutting attachment begins to rotate as
soon as the engine is started by putting
the throttle into the start position. When
starting the engine, place the product
onto the ground in a flat clear area and
hold it firmly in place so as to ensure
that neither the cutting part nor the
throttle come into contact with any
obstacle when the engine starts.
Never place the throttle into the high
speed position when starting the
engine.
3. After starting the engine, check to make
sure that the cutting attachment stops
rotating when the throttle is moved fully
back to its original position. If it
continues to rotate even after the
throttle has been moved fully back, turn
WARNING
IMPORTANT
et blanc par exemple) et poser des
panneaux d’avertissement. Lorsque
deux ou plusieurs personnes travaillent
ensemble ou à proximité, chacune doit
constamment faire attention et garder
ses distances par rapport aux autres
pour assurer une sécurité satisfaisante.
2. Vérifier constamment l’état de la zone
de travail pour éviter tout accident dû
aux impacts avec des obstacles tels
que les souches, les pierres, les boîtes
de conserves ou débris de verre.
Retirer tout obstacle avant de commencer
le travail.
3. Vérifier que la machine ne comporte
aucun élément desserré ou de fuite de
carburant. S’assurer que l’outil de
coupe est monté correctement et bien
serré.
4. S'assurer que le cache de protection
anti-débris est fermement attaché.
5. Utiliser toujours la machine avec son
harnais. Le régler pour un confort
maximal avant de mettre le moteur en
marche. Il doit être ajusté pour que la
main gauche puisse tenir
confortablement la poignée environ à
hauteur de la taille.
DEMARRAGE DU MOTEUR
1. Empêcher toute personne ou animal de
s’approcher à moins de 15 mètres. Si
quelqu’un s’approche trop près, arrêter
aussitôt le moteur.
2. La machine est équipée d’un
embrayage centrifuge et l’outil de coupe
se met à tourner dès que le moteur est
mis en route en plaçant l’accélérateur
en position de démarrage. Pour mettre
le moteur en route, poser et maintenir
fermement la machine à plat sur le sol
dans un endroit dégagé où aucun
obstacle ne peut entrer en contact avec
l’outil de coupe ou la manette
d’accélérateur une fois que le moteur
sera en marche.
Ne jamais mettre la manette de
l’accélérateur à fond lors de la mise en
marche.
3. Une fois le moteur en marche, vérifier
que l’outil de coupe s’arrête de tourner
lorsque l’accélérateur est remis à zéro.
Si l’outil de coupe continue à tourner,
arrêter le moteur et rapporter la
AVERTISSEMENT
IMPORTANT
5. For safe operation 5. Consignes de securite
EspañolDeutsch Italiano
19
Sollten mehrere Personen gleichzeitig
in demselben Bereich arbeiten, stets
auf ausreichenden Abstand achten, um
die Sicherheit aller Mitarbeiter zu
gewährleisten.
2. Den Zustand des Arbeitsbereiches
prüfen, um einen Unfall aufgrund
versteckter Hindernisse wie Stümpfe,
Steine oder zerbrochenes Glas
vermieden werden.
Hindernisse vor Arbeitsbeginn
wegräumen.
3. Prüfen Sie das gesamte Gerät auf
lockere Befestigungen und
Kraftstofflecks. Sicherstellen, daß das
Schneidblatt richtig installiert und fest
fixiert ist.
4. Stellen Sie sicher, daß der Abfallschutz
fest in Position befestigt ist.
5. Immer den Schultergurt verwenden.
Den Gurt vor dem Starten des Motors
so einstellen, daß er beim Betrieb nicht
stört und daß die linke Hand den
Handgriff ohne Probleme ca. auf
Hüfthöhe halten kann.
DEN MOTOR STARTEN
1. Zuschauer und Tiere mindestens 15
Meter vom Arbeitsbereich fernhalten.
Wenn sich Ihnen jemand nähert, sofort
den Motor stoppen.
2. Das Produkt verfügt über einen
Zentrifugalkupplungsmechanismus.
Dadurch beginnt sich das Schneidblatt
zu drehen, sobald der Drosselhebel in
die Startposition gebracht wird. Beim
Starten des Motors, das Produkt auf
einen ebenen Boden stellen und
festhalten, so daß das Schneidteil und
die Drossel bei Start des Motors nicht in
Kontakt mit Fremdkörpern kommen.
Niemals die Drossel in die
Schnellaufposition bewegen, wenn der
Motor gestartet wird.
3. Nach dem Starten des Motors
sicherstellen, daß das Blatt stoppt,
wenn die Drossel zurück in die
Ausgangsposition bewegt wird. Sollte
sich das Blatt weiterhin bewegen, den
Motor sofort abstellen und das Gerät
zur Reparatur einem autorisierten
WARNUNG
WICHTIG
lavoro deve essere eseguito
contemporaneamente da due o più
persone, controllate continuamente la
posizione delle altre persone che
lavorano per mantenere una distanza di
sicurezza tra ciascuna persona,
garantendo così l’incolumità di tutti.
2. Controllate la condizione dell’area di
lavoro per evitare eventuali incidenti
dovuto al contatto con degli ostacoli
nascosti, ad esempio ceppi d’albero,
sassi, bidoni o pezzi di vetro rotto.
Rimovete eventuali ostacoli prima di
cominciare il lavoro.
3. Ispezionate l’intera unità per scoprire
eventuali dispositivi di fissaggi lenti o
eventuali perdite di carburante.
Assicuratevi che la testa tagliente sia
stata installata e fissata in modo ben
saldo.
4. Assicuratevi che la protezione anti-
detriti sia ben salda in posizione.
5. Usate sempre la tracolla. Regolate la
tracolla prima di accendere il motore.
La tracolla va regolata in modo tale che
possiate tenere comodamente con la
mano sinistra l’impugnatura all’altezza
del fianco.
ACCENSIONE DEL MOTORE
1. Assicuratevi che le persone e gli
animali si trovino ad una distanza di
almeno 15 metri dal punto di lavoro. Se
vi si avvicinano, spegnete il motore
immediatamente.
2. Il prodotto è stato dotato di un
meccanismo ad innesto centrifugale, in
modo tale che la testa tagliante inizia a
girare appena si accende il motore
posizionando la leva del gas nella
posizione di avviamento. Prima di
accendere il motore, posizionate il
prodotto sul terreno in un luogo piano e
privo di ostacoli e tenetelo fermo nella
posizione per assicurarvi che né la
parte tagliente né la leva del gas venga
in contatto con eventuali ostacoli
quando si accende il motore.
Non posizionate mai la leva del gas
nella posizione ad alta velocità per
accendere il motore.
3. Dopo aver acceso il motore, controllate
che la testa tagliente smetta di ruotare
appena si rimette la leva del gas nella
IMPORTANTE
advertencia. Cuando el trabajo vaya a
ser realizado simultáneamente por dos
o más personas, también se deberá
tener la precaución de mirar
constantemente alrededor y verificar la
presencia y posición de las demás
personas que están trabajando, a fin de
mantener una distancia prudente entre
cada persona que garantice su
seguridad.
2. Compruebe las condiciones del área de
trabajo a fin de evitar accidentes que
pueden ocurrir al golpear obstáculos
ocultos tales como tocones, piedras,
latas o vidrios rotos.
Quite todos los obstáculos antes de iniciar
el trabajo.
3. Inspeccione la unidad completa para
determinar si tiene sujetadores sueltos
o fugas de combustible. Asegúrese de
que el accesorio de corte esté
debidamente instalado y asegurado.
4. Asegúrese de que el protector contra
desechos se encuentra firmemente
acoplado en su sitio.
5. Utilice siempre la correa de hombro.
Ajuste la correa a su comodidad antes
de arrancar el motor. La correa debe
ajustarse de tal forma que la mano
izquierda pueda sujetar cómodamente
la barra del manillar aproximadamente
a la altura de la cintura.
ARRANQUE DEL MOTOR
1. Mantenga a espectadores y animales a
una distancia de al menos 15 metros
del lugar de uso de la máquina. Si
alguien se aproxima, detenga
inmediatamente el motor.
2. El producto está equipado con un
mecanismo de embrague magnético,
por lo que el accesorio de corte
comienza a girar inmediatamente
cuando se arranca el motor poniendo el
acelerador en posición de arranque. Al
arrancar el motor, ponga el producto en
el suelo, en un lugar plano y despejado,
y sujételo firmemente para asegurarse
de que la pieza de corte y el acelerador
no puedan entrar en contacto con
ningún obstáculo cuando el motor
arranque.
Nunca ponga el acelerador en la
posición de alta velocidad al arrancar
el motor.
3. Después de arrancar el motor,
compruebe que el accesorio de corte
deja de girar cuando usted devuelve
ADVERTENCIA
IMPORTANTE
5. Sicherer Betrieb
5. Per un funzionamento sicuro
5. Instrucciones de seguridad
English Français
20
off the engine and take the unit to your
authorized Komatsu Zenoah servicing
dealer for repair.
USING THE PRODUCT
Cut only materials recommended by
the manufacturer. And use only for
tasks explained in the manual.
1. Grip the handles firmly with both hands
using your whole hand. Place your feet
slightly apart (slightly further apart than
the width of your shoulders) so that
your weight is distributed evenly across
both legs, and always be sure to
maintain a steady, even posture while
working.
2. Keep cutting attachment below waist
level.
3. Maintain the speed of the engine at the
level required to perform cutting work,
and never raise the speed of the engine
above the level necessary.
4. If the unit start to shake or vibrate, turn
off the engine and check the whole unit.
Do not use it until the trouble has been
properly corrected.
5. Keep all parts of your body away from
rotating cutting attachment and hot
surfaces.
6. Never touch the muffler, spark plug, or
other metallic parts of the engine while
the engine is in operation or
immediately after shutting down the
engine. Doing so could result in serious
burns or electrical shock.
IF SOMEONE COMES
1. Guard against hazardous situations at
all times. Warn adults to keep pets and
children away from the area. Be careful
if you are approached. Injury may result
from flying debris.
2. If someone calls out or otherwise
interrupts you while working, always be
sure to turn off the engine before
turning around.
MAINTENANCE
1. In order to maintain your product in
proper working order, perform the
IMPORTANT
machine chez le revendeur agréé pour
la faire réparer.
UTILISATION DE LA MACHINE
Ne couper avec la machine que les
matériaux recommandés par le
fabricant.
1. Tenir les poignées de la machine
fermement des deux mains. Ecarter
légèrement les jambes (pour que les
pieds reposent sur une largeur un peu
plus importante que celle des épaules)
et avoir une posture de travail stable et
répartir le poids du corps également sur
chaque jambe.
2. Maintenir l’outil de coupe toujours plus
bas que le niveau de la taille.
3. Faire tourner le moteur à la vitesse
appropriée à la coupe sans jamais
accélérer inutilement au dessus du
niveau nécessaire.
4. Si la machine se met à vibrer ou à créer
des secousses, arrêter le moteur et
procéder à une vérification totale de la
machine.
5. Se tenir à distance de l’outil de coupe
ou des parties chaudes de la machine.
6. Ne jamais toucher le silencieux, la
bougie ou toute autre partie métallique
du moteur pendant le fonctionnement
ou aussitôt après son arrêt. Dans ces
circonstances, les risques de brûlures
ou d’électrocution sont importants.
SI QUELQU’UN S’APPROCHE
1. Il faut se préserver des situations
dangereuses à tout moment. Avertir les
adultes de maintenir les enfants et les
animaux à distances car le risque de
recevoir des projections d’objet est
important.
2. Si quelqu’un appelle ou interrompt le
travail d’une manière ou d’une autre,
arrêter le moteur avant de se tourner
vers la personne.
ENTRETIEN
1. De manière à conserver la machine en
parfait état de marche, effectuer à
IMPORTANT
5. For safe operation 5. Consignes de securite
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

ZENOAH KOMATSU BC2001 Manuale utente

Categoria
Tagliaerba
Tipo
Manuale utente
Questo manuale è adatto anche per