Zenith Direct-View Concierge H27H38DT Guida d'installazione

Marca: Zenith

Modello: Direct-View Concierge H27H38DT

Categoria: TV LCD

Tipo: Guida d'installazione

Questo manuale è adatto anche per

Direct-View Concierge H32H38DT

Installation Guide & Warranty

Model Numbers | H27H38DT • H32H38DT Direct-View Concierge

TVs

Zenith and the lightning Z logo are registered

trademarks of Zenith Electronics Corporation

Page 2

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the pres-

ence of important operating and maintenance (servicing) instructions in the literature accom-

panying the appliance

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.

ATTENTION: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne

correspondante de la prise et pousser jusqu’au fond.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National

Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system of the building, as close to the point of the cable

entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics

U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

For Customer Support/Service, please call:

1-888-865-3026

www.lgcommercial.com • www.zenith.com

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

2000 Millbrook Drive, Lincolnshire, IL 60069

Concierge

is a registered trademark of Zenith Electronics Corporation

RECORD THE SERIAL NUMBER

The model-serial number of the Concierge

TV is

located on the back of the cabinet. For future refer-

ence, we suggest that you record those numbers

here: MODEL NO.

SERIAL NO.____________________________

Page 3

SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This informa-

tion shall be given in a separate booklet or sheet, or be located before any operat-

ing instructions in an instruction for installation for use and supplied with the

apparatus.

This information shall be given in a language acceptable to the country where the

apparatus is intended to be used.

The important safety instructions shall be entitled “Important Safety Instructions”.

The following safety instructions shall be included where applicable, and, when

used, shall be verbatim as follows. Additional safety information may be included

by adding statements after the end of the following safety instruction list. At the

manufacturer’s option, a picture or drawing that illustrates the intent of a specific

safety instruction may be placed immediately adjacent to that safety instruction:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

1. Do not use this apparatus near

water.

2. Clean only with a dry cloth.

3. Do not block any ventilation open-

ings. Install in accordance with the

manufacturer’s instructions.

4. Do not install near any heat sources

such as radiators, heat registers,

stoves, or other apparatus (including

amplifiers) that produce heat.

5. Do not defeat the safety purpose of

the polarized or grounding-type

plug. A polarized plug has two

blades with one wider than the

other. A grounding-type plug has

two blades and a third grounding

prong. The wide blade or the third

prong are provided for your safety.

If the provided plug does not fit into

your outlet, consult an electrician

for replacement of the obsolete

outlet.

6. Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and

the point where they exit from the

apparatus.

7. Only use attachments/accessories

specified by the manufacturer.

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

Installation Guide & Warranty

Model Numbers | H27H38DT • H32H38DT

Direct-View Concierge TVs

Page 4

IMPORTANT SAFETY INSTRUCTIONS

8. Use only with the cart, stand, tri-

pod, bracket, or table specified by

the manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the

cart/apparatus combination to avoid

injury from tip-over.

9. Unplug this apparatus during light-

ning storms or when unused for

long periods of time.

10. Refer all servicing to qualified serv-

ice personnel. Servicing is required

when the apparatus has been dam-

aged in any way, such as power-

supply cord or plug is damaged, liq-

uid has been spilled or objects have

fallen into the apparatus, the appa-

ratus has been exposed to rain or

moisture, does not operate normally,

or has been dropped.

11. CAUTION, Concerning the Power

Cord: Most appliances recommend

they be placed upon a dedicated

circuit; that is, a single outlet cir-

cuit which powers only that appli-

ance and has no additional outlets

or branch circuits. Check the speci-

fication page of this owner's manual

to be certain.

Do not overload wall outlets.

Overloaded wall outlets, loose or

damaged wall outlets, extension

cords, frayed power cords, or dam-

aged or cracked wire insulation are

dangerous. Any of these conditions

could result in electric shock or fire.

Periodically examine the cord of

your appliance, and if its appear-

ance indicates damage or deteriora-

tion, unplug it, discontinue use of

the appliance, and have the cord

replaced with an exact replacement

part by an authorized servicer.

Protect the power cord from physi-

cal or mechanical abuse, such as

being twisted, kinked, pinched,

closed in a door, or walked upon.

Pay particular attention to plugs,

wall outlets, and the point where

the cord exits the appliance.

12. Outdoor Use Marking:

WARNING -To Reduce The Risk Of

Fire Or Electric Shock, Do Not

Expose This Appliance To Rain Or

Moisture

13. Wet Location Marking: Apparatus

shall not be exposed to dripping or

splashing and no objects filled with

liquids, such as vases, shall be

placed on or over apparatus.

PORTABLE CART WARNING

Page 5

Purchase the Optional Installer’s Remote and Clone Programmer

To perform a normal installation set up, you need an installer’s remote such as the LP702, and the LT2000

Quickset II Clone Programmer—both are shown and described in later sections. The installer remote allows

access to the Installer and User menus. The LT2000 Quickset II Clone Programmer is used to duplicate a

Zenith TV’s setup and install it on another identical Zenith TV. See your LG/Zenith Dealer.

Note: Design and specifications are subject to change without prior notice.

Safety Warnings . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . 5

TV Features Overview . . . . . . . . . . . . . . . . . . 6

Setup Checklist . . . . . . . . . . . . . . . . . . . . . 7

User remote control . . . . . . . . . . . . . . . . . . . 8

Optional Installer’s remote control . . . . . . . . . 9

Connections/Installation Overview . . . . . . . . . 10

Step 1. TV Connections

TV/VCR/Cable Box/and other Equipment Hookup

TV Hook up Directory . . . . . . . . . . . . . . . . . 11

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cable service . . . . . . . . . . . . . . . . . . . . . . . 13

Antenna with VCR . . . . . . . . . . . . . . . . . . . 14

Cable service with VCR . . . . . . . . . . . . . . . . 15

Additional Equipment Hookup

S-Video VCR/DVD etc. . . . . . . . . . . . . . . . . . 16

Composite Audio/Video . . . . . . . . . . . . . . . . 17

External Amplifier (Audio Out [Matrix] hook up) 18

Step 2. TV Reception Set Up & Channel Search

Auto Program: Select Antenna, or Cable service

and start the channel search . . . . . . . . . . . . 19

Front Panel Controls/Source Inputs . . . . . . . . 20

Picture/Sound Source Selection . . . . . . . . . . . 21

Source Menu . . . . . . . . . . . . . . . . . . . . . . . 22

On-Screen Menus/Displays Overview . . . . . . . . 23

Other Menus and On-Screen Displays

Sleep Timer Menu . . . . . . . . . . . . . . . . . . . . 24

Channel/Time/Audio Display . . . . . . . . . . . . . 24

Digital CC Menu . . . . . . . . . . . . . . . . . . . . . 24

Volume Display . . . . . . . . . . . . . . . . . . . . . 24

Closed Captions Menu . . . . . . . . . . . . . . . . . 24

Captions Unknown display . . . . . . . . . . . . . . 24

Ch Preview Menu . . . . . . . . . . . . . . . . . . . . 24

Ghost Channel Display . . . . . . . . . . . . . . . . . 24

Alarm Menu . . . . . . . . . . . . . . . . . . . . . . . 24

Digital Captions Menu . . . . . . . . . . . . . . . . . 24

Step 3. Customize the TV’s Features

Setup Menu

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . 25

Channel Labels (Preset and Custom) . . . . . . . 26

Source Name . . . . . . . . . . . . . . . . . . . . . . . 27

Clock Setup (Auto/Manual) . . . . . . . . . . . . . 28

Timer Setup (On/Off Timers) . . . . . . . . . . . . 29

Captions: Analog-Digital (Setup Overview) . . . 30

Captions: Analog-Digital Menu Structures . . . . 31

Degauss . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Language . . . . . . . . . . . . . . . . . . . . . . . . . 33

Audio Menu . . . . . . . . . . . . . . . . . . . . 34 - 35

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . 36

Parental Control Menu . . . . . . . . . . . . . 37 - 40

Installer Menus . . . . . . . . . . . . . . . . . 41 - 49

LT2000 Quickset II Clone Programmer . . . 50 - 52

Clone Programmer Troubleshooting . . . . . . . . 53

Troubleshooting . . . . . . . . . . . . . . . . . 54 - 57

Maintenance . . . . . . . . . . . . . . . . . . . . . . . 57

Discrete IR Codes . . . . . . . . . . . . . . . . . . . .58

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Warranty . . . . . . . . . . . . . . . . . . . . Back Cover

Use this page as a reference for finding the pages or sections to go to

and set up the TV’s features for the end user

See the Setup Checklist on page 7

Table of Contents

Page 6

TV Features Overview

A brief overview of the features on this TV

Analog and Digital Tuners

This TV is equipped with both analog and digital tuners. The analog tuner is used

for standard over-the-air antenna and cable type (CATV) sources. The digital tuner

is provided to receive over-the-air digital programming.

After running Auto Program on the TV, analog channels will appear numerically

with Channel Up/Down and Digital Channels will appear numerically in the channel

scan after either the highest/lowest analog channel or Aux source.

Installer Menu Default Items

Some items explained in this guide may have different default settings than those

shown on the installer menu pages. As a result, those items may need to be reset

based on the requirements of the institution.

Install a Two-way Signal Splitter?

If there is only one RF lead available, install a two-way splitter in order to be able

to provide 75 ohm RF leads to both the Antenna/Cable and Digital/Antenna inputs

on the TV connections panel.

Available Source Connections

• Antenna/Cable

• Digital/Antenna

• S-Video with Right/Left Audio

• Standard Composite Video with Right/Left Audio

• Matrix Audio Out Speaker

• Front Panel Video with Right/Left Audio Inputs

Features

Analog Menus Digital Menus

• Alarm Menu • Digital Audio (Note: Even though an OSD

• Audio Menu • Digital Captions indicates that digital features

• Captions/Text • Digital Video are available, they may not be

• Language present on the actual channel

• Parental Control picture and sound signals.)

• Sleep Timer

• On/Off Timers

• Screen Degauss

• Video Menu

• XDS Display

Page 7

Setup Checklist

Following are the steps necessary to install and set up the TV

Setup and Operation Checklist

1. Unpack the TV and all accessories.

2. Connect the TV to antenna and all external video source equipment.

See pages 10 - 18.

3. Install batteries in remote control.

See page 11.

4. Plug TV and source equipment into power outlets.

See page 11.

5. Turn TV on.

See pages 8, 9 or 20.

6. Choose on screen menu language.

See page 33. (English is default.)

Reception Setup and Channel Search

8. Use Auto Program* to search for all channels in your area.

See page 19.

7. Select viewing source for TV.

See page 22.

8. Adjust Installer menu per requirements of the lodge entertainment system.

See pages 41 through 49.

Customize the TVs Features for the End User

9. Fine-tune source image and sound to personal preference or as required by

source.

See pages 25 through 40.

Additional Features Setup

See page 5, Table of Contents.

*Auto Program finds channels which have a signal present and are actively being

broadcast. Some broadcasters do not provide or broadcast a signal continuously. As

a result, some DTV channels may not be found in the channel scan. If you know

that there is a DTV channel that was not found by Auto Program, run Auto

Program again; when the DTV channel is actually sending out a program signal.

Page 8

User Remote Control

POWER

FLSHBK

MUTE

CHANNEL

VOLUME

ENTER

ALARM

CH PREVIEW

AUDIO

TIMER

CHANNEL (Up/Down)

Scroll available channels

(analog to digital) and

the Aux Channel (Audio /

Video source). User

Up/Down menu arrows

A list of the keys and their functions on the 6710V00108N user remote

control supplied with the TV

POWER

Turns TV On or Off.

CC (Closed Captions)

Press to turn closed cap-

tions on/off. Press ENTER

to remove menu. In digital

captions, selects next cap-

tion language.

Remote Control part number

6710V00108N

VOLUME Down/Up

Adjusts the sound level.

User Left/Right menu arrows.

Number Keypad

Select channels directly;

key in channel numbers

and press ENTER.

(SLEEP) TIMER

Press repeatedly to

choose a TV turn-off time

up to 4-hours.

Use to set AM/PM on the

Alarm menu.

-DASH (-)

For entering digital chan-

nel numbers e.g. 7-1,

11-3 etc.

AUDIO

Selects available audio

languages for digital

channels only.

Audio Languages: Availability of audio languages are determined only by each broadcaster and

may not be available on all digital programs.

FLASHBK (Flashback)

Returns to the last chan-

nel viewed.

MUTE

Turns sound Off and On,

while the picture remains.

ENTER

Press to view the

Channel/Time/Audio

display or to remove any

on-screen display or menu.

ALARM

Press to display menu, fol-

low on-screen instructions

to set a time for the TV to

turn itself on.

CHANNEL PREVIEW

(Not functional for digital

channels - some models.)

Displays available analog

TV channels, allows hotel

guest access to the Aux

Channel and (if active)

the Guest Parental Control

menu: set V-Chip blocks

on analog channels only

to restrict both analog

and digital programming.

• Aux Channel allows the

guest to select the Audio

/ Video inputs. (Use the

A/V jacks on the back of

the TV as a source).

Page 9

Installer Remote Control

POWER

FLSHBK

MUTE

CHANNEL

VOLUME

ENTER

ALARM

CH PREVIEW

AUDIO

TIMER

SELECT

ADJ

TV/FM

Keys descriptions and their functions for the optional Installer’s remote

Remote Control part number

6710V00108M

CHANNEL (Up/Down)

Scroll available channels,

(analog to digital) and

the Aux Channel

(Audio/Video source).

POWER

Turns TV On or Off.

VOLUME Down/Up

Adjusts the sound level.

Number Keypad

Select channels directly;

key in channel numbers

and press ENTER.

(SLEEP) TIMER

Press repeatedly to choose

a TV turn-off time up to 4-

hours. Use to set AM/PM

on the Alarm and On/Off

Timer menus.

FLASHBK (FLASHBACK)

Returns to the previously

tuned channel.

MUTE

Turns sound Off and On,

while the picture remains.

ENTER

Press to view the

Channel/Time/Audio

display or to remove any

on-screen display or menu.

ALARM

Press to display menu.

Follow on-screen instruc-

tions to set a time for the

TV to turn itself on.

TV/FM (Down Arrow)

Use for the menus down

arrow. If TV has FM radio,

toggles between TV-FM.

MENU/SELECT/ADJ

(Adjust Left/Right)

Selects and adjusts on-

screen menu options.

Press MENU repeatedly to

scroll through menus. Use

SELECT to choose options

and ADJ (Adjust)

Left/Right to change the

selected option.

Audio Languages: Availability of audio languages are determined only by each broadcaster and

may not be available on all digital programs.

CC (Closed Captions)

Press to turn closed cap-

tions on/off. Press ENTER

to remove menu. In digital

captions, selects next cap-

tion language.

-DASH (-)

For entering digital chan-

nel numbers e.g. 7-1, 11-

3 etc.

AUDIO

Selects available audio

languages for digital

channels only.

CHANNEL PREVIEW

(Not functional for digital

channels - some models.)

Displays available analog

TV channels, allows hotel

guest access to the Aux

Channel and (if active)

the Guest Parental Control

menu: set V-Chip blocks

on analog channels only

to restrict both analog

and digital programming.

• Aux Channel allows the

guest to select the Audio

/ Video inputs. (Use the

A/V jacks on the back of

the TV as a source).

Page 10

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Connections/Installation Overview

Use this page for reference when connecting analog or digital signal sources and other source equipment.

To hookup source equipment, refer to the next page; shows pages to go to for equipment hookup options.

Also, see the front connection panel hookup options on page 20.

Notes:

• Digital cable is not available on this TV.

• If only one wire provides the signal source, use a high-quality 2-way RF signal splitter and connect it to

both the Antenna-Cable and Digital Antenna RF jacks on the TV, see below.

Antenna/Cable

Connect analog off air

antenna or analog CATV

signal source here.

Digital Antenna

Connect if digital signal

source is available.

Note: If both digital and

analog signals are only

available from one RF

lead, connect a signal

splitter (not provided).

MPI Ports

Connect LT2000 clone

programmer to either

MPI port.

Note: Do not make con-

nections to both MPI

ports at the same time.

Video In R-Audio-L

Connect composite

Video-Audio source here.

S-Video In R-Audio-L

Connect S-Video-Audio

source here.

Digital Cable (DCATV)

This TV cannot be used for digital cable signals.

Rear Connections Panel

Matrix Out

Connect external speaker

here.

Page 11

IMPORTANT!!!

Use this page to decide where you need to begin your setup. First, find the line

below that best describes what you want to do, then go to that page number. Go

to additional pages as required.

Off Air Antenna Only (provide digital signal to TV if required by using a signal splitter)

If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . . . . . . . . . . . . . page 12

Cable Service Only

If you have cable service and no other equipment, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13

Off Air Antenna with VCR

If you are using an antenna and have a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 14

Cable Service with VCR

If you have cable service and a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15

S-Video

If you want to connect an S-Video VCR/DVD Player etc., go to . . . . . . . . . . . . . . . . . . . . . . . page 16

Composite Video

If you want to hook up a composite video device, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17

External Speaker

Send the TV sound to an external audio system or monaural speaker, go to . . . . . . . . . . . . . . page 18

Install Batteries in User Remote Control

Hookup Directory

Back of

Remote

Remove the back of the remote and install two high-

quality AA batteries. Match “+” with “+”, “-” with “-”.

120 Volt

60 Hz AC

Plug TV into Wall Power Outlet

After all connections

have been made, plug

the TV and all system

equipment into power

sources as applicable.

This TV is designed to

operate on standard

current, 120-volt 60

Hertz AC power. Do not

attempt to operate it

on DC Current.

Available Source Connections

Page 12

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

RF Coaxial Wire

(75ohm)

Antenna

RF Coaxial Wire

(75ohm)

Antenna

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

RF Coaxial Wire

(75ohm)

Antenna

75 ohm

Signal Splitter

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Hook Up an Off Air Antenna

Locate the Antenna/Cable

and Digital/Antenna jacks on

the back of the TV.

Connect the RF antenna

wires that run from the wall

directly to the jacks, accord-

ing to the connection dia-

gram shown to the right.

If you have a 75 ohm RF

cable, then you don’t need

any adapters!

A 300 to 75 ohm adapter is

not included with the Zenith

TV.

Over the Air Antenna

To get digital with only one RF antenna lead, install a 2- way signal splitter

Mini Glossary

2-Way Splitter A device that provides two antenna signals from one antenna lead.

75 ohm The wire that comes from an off-air antenna or cable service provider. Each end

RF Cable looks like a hex shaped nut with a wire sticking through the middle, and it screws

onto the threaded jack on the back of the TV.

300 to (Not shown) A small device that connects a flat two-wire 300 ohm antenna to a 75

75 ohm ohm RF jack. They are usually about an inch long with two screws on one end and a

Adapter round opening with a wire sticking out on the other end.

If there is only one antenna lead

available from the wall antenna

jack, locate the Antenna/Cable

and the Digital/Antenna jacks on

the back of the TV.

Connect the antenna that runs

from the wall directly to a 75

ohm 2-way signal splitter (not

provided) according to the con-

nection diagram shown to the

right.

Connect the two antenna leads

to the TV RF inputs:

Antenna/Cable and Digital

/Antenna. This will provide the

same over-the-air signal to both

the analog and digital RF inputs.

Connect an over the air signal source to the TV

Page 13

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

Cable TV

Wall Jack

RF Coaxial Wire

(75ohm)

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

Cable TV

Wall Jack

Cable Box

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Hook Up Cable Service (CATV)

Locate the Antenna/Cable in jack

on the back of the TV set.

Connect the CATV cable that runs

from the wall according to the

connection diagram shown to the

right.

The TV digital tuner does not

work with a Digital Cable signal

source.

Cable Service

Cable Service with a Cable Box

Locate the Antenna/Cable in jack

on the back of the TV set.

Connect the CATV cable that runs

from the wall to the cable box

and TV according to the connec-

tion diagram shown to the right.

If you’re using a cable box, tune

the TV to channel 3 or 4 and use

your cable box to change

channels.

If you’re using a cable box, Auto

Program might only find the

channel your cable service is on

(usually channel 3 or 4).

The TV digital tuner does not

work with a Digital Cable signal

source.

Connect cable service to the TV

Page 14

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

A/V cables

not included

with TV

RF Coaxial Wire

(75ohm)

Antenna

Off Air

Antenna

RF Coaxial Wire

(75ohm)

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Hook Up an Off Air Antenna with VCR

Locate the Antenna/Cable In jack on the

back of the VCR.

Connect the antenna that runs from the wall

jack directly to this jack, according to the

connection diagram shown to the right.

Connect a 75 ohm wire to the Digital

Antenna input on the TV for digital pro-

gramming.

Make the VCR to TV connections as indicated

in the illustration.

If you have a 75 ohm RF cable, then you

don’t need any adapters!

A 300 to 75 ohm adapter is not included

with the Zenith TV.

Over the Air Antenna with VCR

Connect an over the air signal source to the VCR and TV

No A/V cables are

included with the

TV. Without A/V

cables, most VCRs

will not play video-

cassettes in stereo

sound.

Page 15

Cable TV

Wall Jack

Cable Box

Out

3 4

Output

Switch

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

A/V cables

not included

with TV

RF Coaxial Wire

(75ohm)

Off Air

Antenna

RF Coaxial Wire

(75ohm)

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Hook Up a Cable Box with VCR

Locate the In jacks on the cable box and the

VCR.

Connect a 75 ohm cable between the cable box

wall jack and Cable In on the cable box.

Connect a 75 ohm cable from the Cable out jack

on the cable box to the Ant In jack on the VCR.

Connect a 75 ohm cable between the VCR out

jack on the VCR and the Antenna/Cable In jack

on the TV.

Connect a 75 ohm wire to the Digital Antenna

input on the TV to get digital programming.

Make the other VCR-TV connections as indicated

in the illustration.

For cable service without a cable box, connect a

75 ohm cable between the cable wall jack and

the VCR In jack.

Cable Service with VCR

Connect a cable box and VCR to the TV

No A/V cables are

included with the TV.

Without A/V cables,

most VCRs will not

play videocassettes in

stereo sound.

Page 16

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

S-Video/audio

cables not included

with TV

Audio Out

S-Video

Out

3 4

VCR Back

VCR Back AV Panel

Output

Switch

R L

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Hook Up S-Video DVD Player or VCR

Locate the S-Video out jack on the DVD player or

VCR.

On the DVD player or VCR, connect the S-Video out

jack to the S-Video in jack on the TV according to

the connection diagram shown to the right.

Make the right/left audio connections as indicated.

S-Video DVD Player or VCR

Connect an S-Video source to the TV

Page 17

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

Audio cables

not included

with TV

Composite

Audio/Video

Device

Audio Out

Video Out

Right

Left

Hook Up Composite Audio/Video

Locate the composite audio/video input jacks on the TV.

Connect the composite audio/video input jacks to a composite

audio/video device as shown in the illustration.

Composite Audio/Video

Connect the TV to a composite audio/video source

Audio cable

not included

with TV

Audio In

Speaker Back

M.P.I.

Antenna

Cable

Typical

TV Back

M.P.I.

Digital

Antenna

S-Video

R- Audio - L

Video

Matrix

Out

R- Audio - L

Page 18

Hook Up an External Speaker

Connect the TV to an external speaker or amplifier

External Speaker

Locate the Matrix Out jack on the back of the TV.

Connect the Matrix Out jack to an external speaker or

audio amplifier as indicated in the illustration.

Page 19

Auto Program (Channel Search)

Using the optional Installer’s remote control,

press POWER to turn the TV on.

Press MENU repeatedly until the Setup menu

appears.

Using SELECT on the remote control, high-

light Auto Program on the menu.

Press the Right or Left ADJ arrow to go to

the Auto Program menu.

Using SELECT, choose either Cable TV/Digital

Air or Off-Air Antenna/Digital Air on the

menu (see Mini Glossary below.)

Press the Right or Left ADJ arrow to begin

the Channel Search.

Press ENTER when the channel search is

completed. This is when the progress bars

are filled and a message “COMPLETED SUC-

CESSFULLY” appears on the screen.

Auto Program finds channels being received

by the TV’s analog and digital tuners.

Cable will not work unless you subscribe to a

cable service.

After the channel search is complete, use

the features on the following pages to:

Add/delete/blank channels, Include channel

labels, so that they appear on the channel /

time / audio display. Choose from the preset

label selections.

Channels labels are only available for analog

channels.

Channel search for digital channels is avail-

able in either the cable or off air antenna

option.

Use Auto Program to specify over-the-air Antenna or Cable Service incoming signal source and

automatically store all of the channels found by the channel search in non-volatile memory.

(Do not connect any device to front video input while

TV is in channel search mode.)

Mini Glossary

On the Auto Program Menu, select:

OFF AIR ANTENNA/DIGITAL AIR If only over-the-air channels are available, select

Off-Air Antenna/Digital Air.

CABLE/DIGITAL AIR If you subscribe to a cable service, select Cable TV/Digital Air.

POWER

FLSHBK

MUTE

CHANNEL

VOLUME

ENTER

ALARM

CH PREVIEW

AUDIO

TIMER

SELECT

ADJ

TV/FM

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

SOURCE NAME

CLOCK SET

TIMER

CAPTIONS

DEGAUSS

LANGUAGE

TO PROGRAM

SETUP MENU

3/5

4/6

Page 20

Front Panel Controls / Source Inputs

Using the front panel controls to operate the TV

CC (Captions/Text)

Turns selected caption/text option on and off.

Adjust (Left/Right)

Changes menu options.

Select

Chooses menu options.

Displays on screen menus.

Volume (Down/Up)

Decreases/increases sound level.

Channel (Down/Up)

Chooses next available

channel.

Power

Turns TV on and off.

Video (In) Camport

Input for a video signal from

auxiliary equipment.

L - Audio - R (In)

Left/Right Channel audio input jacks.

The front Video jack is an Auto Sense source connection.

With a cable connected, the TV will automatically change

its source setting to CAMPORT, as indicated on the

channel-time display.

If you have a device connected to the front Video

jack and the Auto sense source connection is turned on, you

will not be able to change channels using the TV tuner until you

have disconnected the device.

Installer Note: The Menu, Select, and Adjust Left/Right keys shown above

do not have legends on the actual TV. These keys are turned Off in the

Installer menu. To enable the Menu, Select and Adjust keys on the front

panel, set installer menu item 11-I to 0. When finished using these keys

it is advisable to disable them by setting item 11-I back to 1; this will

deny the end/user guest access to the onscreen menus on the TV from the

front control panel.

adjust select menu

captions volume channel power

L audio R

video in

Typical Front Panel Controls

La pagina sta caricando ...

Zenith Direct-View Concierge H27H38DT Guida d'installazione

Marca: Zenith

Modello: Direct-View Concierge H27H38DT

Categoria: TV LCD

Tipo: Guida d'installazione

Questo manuale è adatto anche per

Direct-View Concierge H32H38DT

Scarica il pdf

rapporto

in altre lingue

English: Zenith Direct-View Concierge H27H38DT Installation guide

Zenith Direct-View Concierge H27H38DT Guida d'installazione

Questo manuale è adatto anche per

Zenith Direct-View Concierge H27H38DT Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti