Sony SDM-N50 Manuale del proprietario

3-868-361-13 (1)

TFT LCD Color

Computer Display

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Manual de instrucciones

Istruzioni per l’uso

US

DE

FR

IT

ES

SDM-N50

2

Owner’s Record

The model and serial numbers are located at the rear of the unit.

Record these numbers in the spaces provided below. Refer to them

whenever you call upon your dealer regarding this product.

Model No.

Serial No.

To prevent fire or shock hazard, do not expose the

unit to rain or moisture.

Dangerously high voltages are present inside the

unit. Do not open the cabinet. Refer servicing to

qualified personnel only.

FCC Notice

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

INFORMATION

This product complies with Swedish National Council for Metrology

(MPR) standards issued in December 1990 (MPR II) for very low

frequency (VLF) and extremely low frequency (ELF).

INFORMATION

Ce produit est conforme aux normes du Swedish National Council

for Metrology de décembre 1990 (MPR II) en ce qui concerne les

fréquences très basses (VLF) et extrêmement basses (ELF).

INFORMACIÓN

Este producto cumple las normas del Consejo Nacional Sueco para

Metrología (MPR) emitidas en diciembre de 1990 (MPR II) para

frecuencias muy bajas (VLF) y frecuencias extremadamente bajas (ELF).

WARNING

NOTICE

This notice is applicable for USA/Canada only.

If shipped to USA/Canada, install only a UL LISTED/CSA

LABELLED power supply cord meeting the following

specifications:

SPECIFICATIONS

Plug Type Nema-Plug 5-15p

Cord Type SVT or SJT, minimum 3 × 18 AWG

Length Maximum 15 feet

Rating Minimum 7 A, 125 V

NOTICE

Cette notice s’applique aux Etats-Unis et au Canada

uniquement.

Si cet appareil est export* aux Etats-Unis ou au Canada, utiliser

le cordon d’alimentation portant la mention UL LISTED/CSA

LABELLED et remplissant les conditions suivantes:

SPECIFICATIONS

Type de fiche Fiche Nema 5-15 broches

Cordon Type SVT ou SJT, minimum 3 × 18 AWG

Longueur Maximum 15 pieds

Tension Minimum 7 A, 125 V

As an

E

NERGY

S

TAR Partner, Sony

Corporation has determined that this

product meets the

E

NERGY

S

TAR

guidelines for energy efficiency.

Declaration of Conformity

Trade Name: Sony

Model No.: SDM-N50

Responsible Party: Sony Electronics Inc.

Address: 1 Sony Drive, Park Ridge, NJ. 07656 USA

Telephone No.: 201-930-6970

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

3

Table of Contents

• Macintosh is a trademark licensed to

Apple Computer, Inc., registered in the

U.S.A. and other countries.

• Windows



and MS-DOS are registered

trademarks of Microsoft Corporation in

the United States and other countries.

• IBM PC/AT and VGA are registered

trademarks of IBM Corporation of the

U.S.A.

• VESA and DDC



are trademarks of the

Video Electronics Standard

Association.

•

E

NERGY

S

TAR is a U.S. registered

mark.

• All other product names mentioned

herein may be the trademarks or

registered trademarks of their respective

companies.

• Furthermore, “



” and “



” are not

mentioned in each case in this manual.

US

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

To enjoy clear sound from the built-in stereo speaker . . . . . . . . . . . 5

Identifying parts and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Step 1:

Connect the media engine to your computer . . . . . . . . . . . 8

Step 2:

Connect the display and media engine . . . . . . . . . . . . . . . . 8

Step 3:

Connect the power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 4:

Turn on the monitor and computer . . . . . . . . . . . . . . . . . . . 9

Using the stereo speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Selecting the input signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Customizing Your Monitor . . . . . . . . . . . . . . . . . . . . . . .11

Navigating the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting the contrast (CONTRAST) . . . . . . . . . . . . . . . . . . . . . . . 12

Adjusting the black level of an image (BRIGHTNESS) . . . . . . . . . 12

Eliminating flicker or blurring (PHASE/PITCH) . . . . . . . . . . . . . . . 13

Adjusting the picture position (H CENTER/V CENTER) . . . . . . . . 13

Displaying a low-resolution signal at the actual resolution

(ZOOM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting the color temperature (COLOR) . . . . . . . . . . . . . . . . . . . 14

Changing the menu’s position (MENU POSITION) . . . . . . . . . . . . 14

Resetting the adjustments (RESET) . . . . . . . . . . . . . . . . . . . . . . . 15

Additional settings (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Technical Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Power saving function (user sensor/power saving mode) . . . . . . . 17

Automatic brightness adjustment function (light sensor) . . . . . . . . 18

Automatic picture quality adjustment function . . . . . . . . . . . . . . . . 18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

On-screen messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Trouble symptoms and remedies . . . . . . . . . . . . . . . . . . . . . . . . . 20

Self-diagnosis function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

Preset mode timing table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

4

Precautions

Warning on power connections

• Use the supplied power cord. If you use a different power cord,

be sure that it is compatible with your local power supply.

For the customers in the U.S.A.

If you do not use the appropriate cord, this monitor will not

conform to mandatory FCC standards.

For the customers in the UK

If you use the monitor in the UK, please use the appropriate UK

power cord.

Installation

Do not install or leave the monitor:

• In places subject to extreme temperatures, for example near a

radiator, heating vent, or in direct sunlight. Subjecting the

monitor to extreme temperatures, such as in an automobile

parked in direct sunlight or near a heating vent, could cause

deformations of the casing or malfunctions.

• In places subject to mechanical vibration or shock.

• Near any equipment that generates a strong magnetic field,

such as a TV or various other household appliances.

• In places subject to inordinate amounts of dust, dirt, or sand, for

example near an open window or an outdoor exit. If setting up

temporarily in an outdoor environment, be sure to take

adequate precautions against airborne dust and dirt. Otherwise

irreparable malfunctions could occur.

Handling the LCD screen

• Do not leave the LCD screen facing the sun as it can damage

the LCD screen. Take care when you place the monitor by a

window.

• Do not push on or scratch the LCD screen. Do not place a heavy

object on the LCD screen. This may cause the screen to lose

uniformity or cause LCD panel malfunctions.

• If the monitor is used in a cold place, a residual image may

appear on the screen. This is not a malfunction. The screen

returns to normal as the temperature rises to a normal operating

level.

• If a still picture is displayed for a long time, a residual image

may appear for a while. The residual image will eventually

disappear.

• The LCD panel becomes warm during operation. This is not a

malfunction.

Maintenance

• Be sure to unplug the power cord from the power outlet before

cleaning your monitor.

• Clean the LCD screen with a soft cloth. If you use a glass

cleaning liquid, do not use any type of cleaner containing an

anti-static solution or similar additive as this may scratch the

LCD screen’s coating.

• Clean the cabinet, panel, and controls with a soft cloth lightly

moistened with a mild detergent solution. Do not use any type

of abrasive pad, scouring powder, or solvent, such as alcohol or

benzine.

• Do not rub, touch, or tap the surface of the screen with sharp or

abrasive items such as a ballpoint pen or screwdriver. This type

of contact may result in a scratched picture tube.

• Note that material deterioration or LCD screen coating

degradation may occur if the monitor is exposed to volatile

solvents such as insecticide, or if prolonged contact is

maintained with rubber or vinyl materials.

Transportation

• Disconnect all cables from the monitor when transporting.

When you transport this display, grasp the support and base

sections of the display stand firmly with both hands. Also use

both hands when carrying the media engine. If you drop the

monitor, you may be injured or the monitor may be damaged.

• When you transport this monitor for repair or shipment, use the

original carton and packing materials.

Replacement of the fluorescent tube

A specially designed fluorescent tube is installed as the lighting

apparatus for this monitor. If the screen becomes dark, unstable,

or does not turn on, replace the fluorescent tube with a new one.

Consult your Sony dealer when replacing the fluorescent tube.

Disposal of the monitor

• Do not dispose of this monitor with general

household waste.

• The fluorescent tube used in this monitor contains

mercury. Disposal of this monitor must be carried out

in accordance to the regulations of your local

sanitation authority.

The equipment should be installed near an easily accessible

outlet.

Example of plug types

for 100 to 120 V AC for 200 to 240 V AC for 240 V AC only

5

US

To adjust the tilt and height

This display can be adjusted within the angles shown below.

To adjust the angles, grasp the lower sides of the LCD panel with

both hands as shown below. Tilt the LCD panel adequately

backward, then lift the LCD panel upward to the desired screen

height, then adjust the screen tilt as desired. When adjusting the

screen height and tilt, proceed slowly and carefully, being sure not

to hit the LCD panel against the desk or the base of the display

stand.

To use the display comfortably

This display is designed so that you can set it up at a comfortable

viewing angle. Adjust the viewing angle of your display

according to the height of the desk and chair, and so that light is

not reflected from the screen to your eyes.

To enjoy clear sound from the built-

in stereo speaker

This monitor has a built-in stereo speaker in base of the display

stand.

We recommend that you position the LCD panel slightly away

from the display stand. High tones from the speaker may be

muffled if the LCD panel is positioned immediately on top of the

stand. Be careful not to drop any metal object into the speaker's

vents as the speakers generate a magnetic field. Also, this

magnetic field may affect data stored on magnetic tapes and discs.

Be sure to keep magnetic recording equipment, tapes, and floppy

discs away from the speaker’s opening.

A duct is provided on the rear part of the display stand to boost the

bass. Be sure not to block the duct with paper or other objects to

ensure clear sound.

90°

40°

50°

m

Ducts

Keep the LCD panel

slightly away from

the base.

Speaker

6

Identifying parts and controls

See the pages in parentheses for further details.

1 1 (Power) switch and indicator (pages 9, 17, 22)

This switch turns the display on and off.

The indicator lights up in green when the monitor is turned on.

The indicator flashes in green and orange when the monitor is

in low power consumption mode, and lights up in orange

when the monitor is in power saving mode.

2 Light sensor and user sensor (pages 16, 17, 18)

These sensors measure the brightness of the surrounding area

and detect when a user becomes present in front of the screen.

Be sure not to cover the sensor with papers, etc.

3 MENU button (page 12)

This button displays the main menu.

4 6 (contrast) button (page 12)

This button displays the CONTRAST menu.

5 8 (brightness) button (page 12)

This button displays the BRITGHTNESS menu.

6 2 (volume) +/– and

M

(+)/

m

(–) buttons

(pages 10, 12)

These buttons display the VOLUME menu and function as

the

M

(+)/

m

(–) buttons when selecting the menu items and

making adjustments.

7 INPUT and OK button, and indicator (pages 10, 12)

This button selects the INPUT 1 or INPUT 2 (HD15 (RGB)

connectors) video input signal. The input signal and

corresponding input indicator change each time you press this

button.

This button also functions as the OK button when displaying

the menu on the screen.

8 Stereo speaker (page 10)

This outputs the audio signals as sound.

9 Ducts

These are used to boost the bass sound from the speaker.

0 SYSTEM CONNECTOR (page 8)

This connector inputs signals from the media engine when the

display and the media engine are connected with a system

connecting cable.

qa Headphones jack (page 10)

This jack outputs audio signals to the headphones.

MENU

INPUT

OK

1

2

SYSTEM CONNECTER

LCD display

Front

Rear

7

US

Media engine

qs AUDIO IN jack (page 10)

This jack inputs audio signals when connecting to the audio

output jack of the computer or other audio equipment.

qd SYSTEM CONNECTOR (TO DISPLAY) (page 8)

This connector outputs signals to the display when the display

and the media engine are connected with a system connecting

cable.

qf HD15 (RGB) input 1 connector (INPUT1) (page 8)

This connector inputs RGB video signals (0.700 Vp-p,

positive) and SYNC signals.

* DDC (Display Data Channel) is a standard of VESA.

qg HD15 (RGB) input 2 connector (INPUT2) (page 8)

This connector inputs RGB video signals (0.700 Vp-p,

positive) and SYNC signals. The pin assignment is the same

as qf.

qh AC IN connector (page 9)

This connector provides AC power to the monitor.

qj AC power switch (page 9)

This switch turns the monitor on and off. When the AC power

switch is turned on, the display automatically turns on.

qk AC power indicator (page 17)

This indicator lights up in green when the media engine is

turned on. The indicator lights up in red when the display is

turned off with the media engine on. The indicator lights up in

orange when the monitor is in the power saving mode.

ql Media engine stand

This stand is used to install the media engine vertically.

Caution

Be sure to install the media engine vertically shown as left. Installing the

media engine lying flat may block ventilation, and may cause a

malfunction.

Pin No. Signal

1Red

2 Green

(Sync on Green)

3Blue

4 ID (Ground)

5 DDC Ground*

6 Red Ground

7 Green Ground

8 Blue Ground

9 DDC + 5V*

10 Ground

11 ID (Ground)

12 Bi-Directional Data (SDA)*

13 H. Sync

14 V. Sync

15 Data Clock (SCL)*

SYSTEM CONNECTER

(

TO DISPLAY

)

INPUT 1

INPUT 2

AUDIO IN

5 4 3 2

1

678910

1112131415

8

Setup

Before using your monitor, check that the following accessories

are included in your carton:

• LCD display

• Media engine

• Media engine stand

•Power cord

• System connecting cable (2 m)

(applicable cable type: DP-2)

• HD15 (RGB) video signal cable

• Audio cord (stereo miniplug)

• Macintosh adapter

• Windows Monitor Information Disk/Utility Disk

• Macintosh Utility Disk

• Warranty card

• Notes for Macintosh users

• This instruction manual

Step 1:Connect the media engine

to your computer

Turn off the media engine and computer before connecting.

Note

Do not touch the pins of the video signal cable connector as this might

bend the pins.

x

Connecting to an IBM PC/AT or compatible

computer

x

Connecting to a Macintosh or compatible

computer

* Refer to the supplied “Notes for Macintosh users” for further details.

Step 2:Connect the display and

media engine

Turn off the display and media engine before connecting.

Caution

Be sure to install the media engine vertically shown as above. Installing

the media engine lying flat may block ventilation, and may cause a

malfunction.

Note

Grasp the plug when connecting the cable.

to INPUT1 or

INPUT2 connector

HD15 (RGB) video

signal cable (supplied)

to video output

IBM PC/AT or

compatible computer

IBM PC/AT or

compatible computer

Use the supplied Macintosh adapter.

to INPUT1 or

INPUT2 connector

Macintosh adapter

(supplied)

*

HD15 (RGB) video

signal cable (supplied)

to video output

Macintosh or

compatible computer

to SYSTEM

CONNECTOR of the

media engine

system connecting

cable (2 m) (supplied)

to SYSTEM

CONNECTOR

of the display

9

US

Step 3:Connect the power cord

With the media engine, display, and computer switched off,

first connect the power cord to the media engine, then connect it

to a power outlet.

Step 4:Turn on the monitor and

computer

1

Turn on the media engine.

The display automatically turns on. The indicators of the

media engine and display light up in green.

2

Turn on the computer.

The installation of your monitor is complete. If necessary, use the

monitor’s controls to adjust the picture.

If no picture appears on your screen

• Check that the monitor is correctly connected to the computer.

• Check that the media engine is on.

• If NO INPUT SIGNAL appears on the screen, try changing the

input signal (page 10), and confirm that your computer’s

graphic board is completely seated in the correct bus slot.

• If OUT OF SCAN RANGE appears on the screen, reconnect

the old monitor. Then adjust the computer’s graphic board so

that the horizontal frequency is between 30 – 61 kHz, and the

vertical frequency is between 50 – 85 Hz (only XGA mode at

75 Hz).

For more information about the on-screen messages, see “Trouble

symptoms and remedies” on page 20.

For customers using Windows 95/98

To maximize the potential of your monitor, install the new model

information file from the supplied Windows Monitor Information Disk

onto your PC.

This monitor complies with the “VESA DDC” Plug & Play standard. If

your PC/graphics board complies with DDC, select “Plug & Play Monitor

(VESA DDC)” or this monitor’s model name as the monitor type in the

“Control Panel” of Windows 95/98. If your PC/graphics board has

difficulty communicating with this monitor, load the Windows Monitor

Information Disk and select this monitor’s model name as the monitor

type.

For customers using Windows NT4.0

Monitor setup in Windows NT4.0 is different from Windows 95/98 and

does not involve the selection of monitor type. Refer to the Windows

NT4.0 instruction manual for further details on adjusting the resolution,

refresh rate, and number of colors.

Adjusting the monitor’s resolution and color number

Adjust the monitor’s resolution and color number by referring to your

computer’s instruction manual. The color number may vary according to

your computer or video board. The color palette setting and the actual

number of colors are as follows:

• High Color (16 bit)

t

65,536 colors

• True Color (24 bit)

t

about 16.77 million colors

In true color mode (24 bit), speed may be slower.

to a power outlet

power cord (supplied)

to AC IN

10

Using the stereo speaker

You can listen to music, sounds, and other audio files using the

stereo speaker of your monitor.

Connect the AUDIO IN jack to the audio output jack of your

computer or other audio equipment using the supplied audio cord

(stereo miniplug).

Adjusting the volume

Volume adjustments are made using a separate VOLUME menu

from the main menu (page 11).

1

Press the 2 +/– buttons.

The VOLUME menu appears on the screen.

2

Press the 2 +/– button to adjust the volume.

The menu automatically disappears after about 3 seconds.

Using the headphones jack

You can listen to the audio signals from your computer or other

audio equipment using headphones. Connect your headphones to

the headphones jack. The speaker turns off when headphones are

connected to the headphones jack. Adjust the volume of the

headphones using the VOLUME menu.

Notes

• You cannot adjust the volume when displaying the main menu on the

screen.

• When your monitor is in low power consumption mode or power

saving mode, no sound comes from the speaker.

Selecting the input signal

You can connect two computers to this monitor using the INPUT

1 and INPUT 2 connectors. To select one of the two computers,

use the INPUT button.

Press the INPUT button.

The input signal and corresponding input indicator, “1” (INPUT

1) or “2” (INPUT 2) change each time you press this button.

Notes

• You cannot select the input signal when displaying the main menu on

the screen.

• If no signal is input to the selected connector, NO INPUT SIGNAL

appears on the screen. After a few seconds, the monitor enters the

power saving mode. If this happens, select the other connector using the

INPUT button.

VOLUME

40

INPUT

OK

1

2

11

US

Customizing Your Monitor

You can make numerous adjustments to your monitor using the

on-screen menu.

Navigating the menu

Press the MENU button to display the main menu on your screen.

See page 12 for more information on using the MENU button.

Use the

M

(+)/

m

(–) and OK buttons to select one of the following

menus. See page 12 for more information on using the

M

(+)/

m

(–) and OK buttons.

Before making adjustments

Connect the monitor and the computer, and turn them on.

Wait for at least 30 minutes before making adjustments for the

best result.

1 PHASE (page 13)

Select the PHASE menu to

adjust the phase when the

characters or pictures appear

fuzzy throughout the entire

screen. Adjust the phase after

adjusting the pitch.

2 PITCH (page 13)

Select the PITCH menu to

adjust the pitch when the

characters or pictures are

unclear in some areas of the

screen.

3 H CENTER (page 13)

Select the H CENTER menu

to adjust the picture’s

horizontal centering.

MENU

PHASE

16

EXIT

PHASE

0

EXIT

PITCH

50

EXIT

HCENTER

4 V CENTER (page 13)

Select the V CENTER menu

to adjust the picture’s vertical

centering.

5 ZOOM (page 14)

Select the ZOOM menu to

adjust the picture’s sharpness

according to the input

signal’s aspect ratio or

resolution.

6 COLOR (page 14)

Select the COLOR menu to

adjust the color temperature

of the picture. This adjusts

the tone of the screen.

7 MENU POSITION

(page 14)

Select the MENU

POSITION to change the on-

screen menu position.

8 RESET (page 15)

Select the RESET menu to

reset the adjustments.

9 Option (page 15)

Select

m

(option) menu to

adjust the monitor’s options.

The options include:

• WIDE STEREO

• BASS BOOST

• BACKLIGHT

• LIGHT SENSOR

• POWER SAVE

• USER SENSOR

• LANGUAGE

• MENU LOCK

25

EXIT

VCENTER

ON

OFF

ZOOM

EXIT

9300K

0K

650

5

0

00K

USER

ALDJUST

COLOR

EXI T

MEN NUP

OS I IOT

EXI T

SCREEN

ALL

RESET

EXI T

1

2

OFF

WI DE STEREO

EXI T

(continued)

12

x

Using the MENU,

M

(+)/

m

(–), and OK buttons

1

Display the main menu.

Press the MENU button to display the main menu on your

screen.

2

Select the menu you want to adjust.

Press the

M

(+)/

m

(–) buttons to display the desired menu.

Press the OK button to select the menu item.

3

Adjust the menu.

Press the

M

(+)/

m

(–) buttons to make the adjustment. Then

press the OK button to return to the previous menu.

4

Close the menu.

Press the MENU button once to return to normal viewing. If

no buttons are pressed, the menu closes automatically after

about 30 seconds.

x

Resetting the adjustments

You can reset the adjustments using the RESET menu. See

page 15 for more information on resetting the adjustments.

Adjusting the contrast (CONTRAST)

Contrast adjustment is made using a separate CONTRAST menu

from the main menu (page 11). This setting is stored in memory

for the signal from the currently selected input connector.

1

Press the 6 (contrast) button.

The CONTRAST menu appears on the screen.

Displaying the current input signal

The horizontal and vertical frequencies of the current input signal are

displayed in the CONTRAST and BRIGHTNESS menu.

2

Press the

M

(+)/

m

(–) buttons to adjust the contrast.

The menu automatically disappears after about 3 seconds.

Adjusting the black level of an

image (BRIGHTNESS)

Brightness adjustment is made using a separate BRIGHTNESS

menu from the main menu (page 11). This setting is stored in

memory for the signal from the currently selected input

connector.

1

Press the 8 (brightness) button.

The BRIGHTNESS menu appears on the screen.

2

Press the

M

(+)/

m

(–) buttons to adjust the

brightness.

If the screen is too bright

Adjust the backlight. For more information about adjusting the

backlight see “Adjusting the backlight” on page 16.

The menu automatically disappears after about 3 seconds.

Note

You can adjust neither contrast nor brightness when displaying the main

menu on the screen.

MENU

INPUT

OK

1

2

,

INPUT

OK

1

2

,

MENU

48.4kHz/ 60Hz

CONTRAST

70

Horizontal frequency

of the current input

signal

Vertical frequency of

the current input

signal

48.4kHz/ 60Hz

B NESSRIGHT

50

Horizontal frequency

of the current input

signal

Vertical frequency of

the current input

signal

13

US

Eliminating flicker or blurring

(PHASE/PITCH)

When the monitor receives an input signal, the automatic picture

quality adjustment function of this monitor automatically adjusts

the picture position, phase, and pitch, and ensures that a clear

picture appears on the screen. For more information about this

function, see “Automatic picture quality adjustment function” on

page 18.

For some input signals, this function may not completely adjust

the picture position, phase, and pitch. In this case, you can

manually set these adjustments according the following

instructions. If you manually set these adjustments, they are

stored in memory and automatically recalled whenever the

monitor receives the same input signals.

These settings may have to be repeated if you change the input

signal after reconnecting your computer.

1

Set the resolution to 1024

×

××

×

768 on the computer.

2

Load the Utility Disk.

Use the appropriate disk for your computer.

For Windows 95/98

Windows Monitor Information Disk/Utility Disk

For Macintosh

Macintosh Utility Disk

3

Start the Utility Disk and display the test pattern.

For Windows 95/98

Click [Utility Disk]

t

[Windows]/[Utility.exe].

For Macintosh

Click [Utility Disk]

t

[SONY-Utility].

4

Press the MENU button.

The main menu appears on the screen.

5

Press the

M

(+)/

m

(–) buttons to select (PITCH)

and press the OK button.

The PITCH menu appears on the screen.

6

Press the

M

(+)/

m

(–) buttons until the screen color

becomes uniform.

Adjust so that the vertical stripes disappear.

7

Press the OK button.

The main menu appears on the screen.

If horizontal stripes are observed over the entire screen, adjust

the phase as the next step.

8

Press the

M

(+)/

m

(–) buttons to select (PHASE)

and press the OK button.

The PHASE menu appears on the screen.

9

Press the

M

(+)/

m

(–) buttons until the screen color

becomes uniform.

Adjust so that the horizontal stripes are at a minimum.

10

Click [ END] on the screen to turn off the test pattern.

To reset the automatic picture quality adjustment

Select SCREEN RESET and activate it using the RESET menu. See

page 15 for more information on using the RESET menu.

Adjusting the picture position

(H CENTER/V CENTER)

If the picture is not in the center of the screen, adjust the picture’s

centering as follows.

These settings may have to be repeated if you change the input

signal after reconnecting your computer.

1

Start the Utility Disk and display the test pattern.

Repeat steps 2 and 3 of “Eliminating flicker or blurring

(PHASE/PITCH).”

2

Press the MENU button.

The main menu appears on the screen.

3

Press the

M

(+)/

m

(–) buttons to select (H

CENTER) or (V CENTER) and press the OK

button.

The H CENTER or V CENTER menu appears on the screen.

4

Move the picture up, down, left, or right until the

frame at the perimeter of the test pattern

disappears.

Press the

M

(+)/

m

(–) buttons to adjust the picture’s

centering using the H CENTER menu for horizontal

adjustment, or the V CENTER menu for vertical

adjustment.

5

Click [END] on the screen to turn off the test pattern.

14

Displaying a low-resolution signal

at the actual resolution (ZOOM)

This monitor is preset at the factory to display pictures on the

screen in full, irrespective of the picture’s mode or resolution.

You can also view the picture at its actual resolution.

1

Press the MENU button.

The main menu appears on the screen.

2

Press the

M

(+)/

m

(–) buttons to select (ZOOM)

and press the OK button.

The ZOOM menu appears on the screen.

3

Press the

m

(–) button to select OFF.

The input signal is displayed on the screen at its actual

resolution.

To display the picture on the screen in full

Select ON in step 3.

Adjusting the color temperature

(COLOR)

The COLOR settings allow you to adjust the picture’s color

temperature by changing the color level of the white color field.

Colors appear reddish if the temperature is low, and bluish if the

temperature is high.

9300K is generally suitable for word processing and other text

oriented applications, and 6500K is generally suitable for video

images.

You can set the color temperature to 5000K, 6500K, 9300K or

user adjustment.

1

Press the MENU button.

The main menu appears on the screen.

2

Press the

M

(+)/

m

(–) buttons to select (COLOR)

and press the OK button.

The COLOR menu appears on the screen.

3

Press the

M

(+)/

m

(–) buttons to select the desired

color temperature.

The preset color temperatures are 5000K, 6500K, and 9300K.

Since the default setting is 9300K, the whites will change

from a bluish hue to a reddish hue as the temperature is

lowered to 6500K and 5000K.

You can set separate color temperatures for each of the video

input signals.

4

If necessary, fine tune the color temperature.

First press the

M

(+)/

m

(–) buttons to select ADJUST and

press the OK button. Then press the

M

(+)/

m

(–) buttons to

select R (Red) or B (Blue) and press the OK button, and then

press the

M

(+)/

m

(–) buttons to adjust the color temperature.

Since this adjustment changes the color temperature by

increasing or decreasing the R and B components with respect

to G (green), the G component is fixed.

If you fine tune the color temperature, the new color setting is

stored in memory for USER ADJUSTMENT and

automatically recalled whenever USER is selected.

The USER ADJUSTMENT setting is common to both the

input signals. If you change the user adjustment setting for

one input signal, the setting for the other input signal is also

changed.

Changing the menu’s position

(MENU POSITION)

You can change the menu position if it is blocking an image on

the screen.

1

Press the MENU button.

The main menu appears on the screen.

2

Press the

M

(+)/

m

(–) buttons to select (MENU

POSITION) and press the OK button.

The MENU POSITION menu appears on the screen.

3

Press the

M

(+)/

m

(–) buttons to select the desired

position.

There are three positions each for the top of the screen and the

bottom of the screen, and one for the screen center.

R168

G170

B175

EXI T

USER ADJUST TMEN

15

US

Resetting the adjustments (RESET)

This monitor has the following two reset methods. Use the

RESET menu to reset the adjustments.

1

Press the MENU button.

The main menu appears on the screen.

2

Press the

M

(+)/

m

(–) buttons to select (RESET)

and press the OK button.

The RESET menu appears on the screen.

Reset the settings according to the following instructions.

Resetting the adjustment data most appropriately

for the current input signal

Press the

M

(+)/

m

(–) buttons to select SCREEN RESET

and press the OK button.

The automatic picture quality adjustment function of this monitor

automatically adjusts the picture position, phase, and pitch, to the

most appropriate value. If this function is activated, the phase is

automatically adjusted whenever the monitor receives the same

input signal.

The RESET menu is automatically returned to the main menu

after the adjustment data is reset.

Resetting all of the adjustment data for all input

signals

Press the

M

(+)/

m

(–) buttons to select ALL RESET and

press the OK button.

The RESET menu is automatically returned to the main menu

after the adjustment data is reset.

To cancel resetting

Press the

M

(+)/

m

(–) buttons to select and press the

OK button.

The RESET menu returns to the main menu without resetting the

adjustment data.

Additional settings (Option)

You can adjust the following options:

• WIDE STEREO

• BASS BOOST

• BACKLIGHT

• LIGHT SENSOR

• POWER SAVE

• USER SENSOR

• LANGUAGE

•MENU LOCK

1

Press the MENU button.

The main menu appears on the screen.

2

Press the

M

(+)/

m

(–) buttons to select

m

.

The option menu appears on the screen.

3

Press the

M

(+)/

m

(–) buttons to select the desired

option item and press the OK button.

Adjust the selected option item according to the following

instructions.

Increasing the soundscape (wide stereo function)

This adjustment makes use of the DSP and creates the illusion of

the built-in stereo speaker being further away than it actually is,

thus enhancing sound presence.

First press the

M

(+)/

m

(–) buttons to select (WIDE

STEREO) and press the OK button. Then press the

M

(+)/

m

(–) buttons to select either 2, 1, or OFF.

The wide stereo function is used to increase the soundscape.

Selecting 1 or 2 increases incrementally the soundscape effect

toward the front of the monitor.

Notes

• If your connected computer or audio equipment uses special sound

functions, such as surround sound, be sure to turn these functions off.

If these functions are being used with the wide stereo function of this

monitor, the wide stereo function may not function properly and thus

not produce the desired sound effect.

• This function is automatically turned off when you use headphones.

However, in this case, the indication in the WIDE STEREO menu does

not change.

• The wide stereo function allows you to increase the soundscape by

converting the analog signals into digital. The sound may be distorted

depending on the input signal and music. In this case, decrease the

volume or set the wide stereo function to OFF.

Boosting the bass (bass boost function)

This option increases the bass output of the speaker.

First press the

M

(+)/

m

(–) buttons to select (BASS

BOOST) and press the OK button. Then press the

M

(+)/

m

(–) buttons to select either ON or OFF.

(continued)

16

Adjusting the backlight

If the screen is too bright, adjust the backlight.

First press the

M

(+)/

m

(–) buttons to select

(BACKLIGHT) and press the OK button. Then press

the

M

(+)/

m

(–) buttons to adjust the desired light level.

Automatically adjusting the screen brightness

(light sensor)

This monitor is provided with a sensor to detect the brightness of

the surrounding area (light sensor). This sensor is used to

automatically adjust the brightness of the screen.

First press the

M

(+)/

m

(–) buttons to select (LIGHT

SENSOR) and press the OK button. Then press the

M

(+)/

m

(–) buttons to select either ON or OFF.

When you select ON, the monitor automatically adjusts the screen

brightness according to the brightness of the surroundings. For

more information about this function, see “Automatic brightness

adjustment function (light sensor)” on page 18.

Note

If this function is set to ON, the value of the BACKLIGHT menu does not

change. If the screen brightness is still not appropriate after the automatic

adjustment, you can manually adjust the backlight. After the backlight

adjustment is made, the monitor automatically adjusts the screen

brightness in accordance with the new backlight value.

Setting up the power saving mode

This monitor has a function which enables it to enter the power

save mode automatically according to the power saving settings

of the computer. You can prevent the monitor from entering the

power saving mode by setting the following option to OFF.

First press the

M

(+)/

m

(–) buttons to select (POWER

SAVE) and press the OK button. Then press the

M

(+)/

m

(–) buttons to select either ON or OFF.

Using the user sensor

The user sensor function enables the monitor to enter the low

power consumption mode when no one is present in front of the

monitor.

First press the

M

(+)/

m

(–) buttons to select (USER

SENSOR) and press the OK button. Then press the

M

(+)/

m

(–) buttons to select either ON or OFF.

If you select ON, the monitor automatically enters the low power

consumption mode when you move away from the front of the

monitor. For more information about the low power consumption

mode, see “Power saving function (user sensor/power saving

mode)” on page 17.

Selecting the on-screen menu language

English, German, French, Spanish, Italian and Japanese versions

of the on-screen menus are available. The default setting is

English.

First press the

M

(+)/

m

(–) buttons to select

(LANGUAGE) and press the OK button. Then press

the

M

(+)/

m

(–) button to select a language.

• ENGLISH

• DEUTSCH: German

• FRANÇAIS: French

• ESPAÑOL: Spanish

• ITALIANO: Italian

• : Japanese

Locking the menus and controls

You can protect adjustment data by locking the menus and

controls.

First press the

M

(+)/

m

(–) buttons to select (MENU

LOCK) and press the OK button. Then press the

M

(+)/

m

(–) buttons and select ON.

Only the 1 (power) switch, and (MENU LOCK) of the

option menu will operate. If any other items are selected, the

mark appears on the screen.

To cancel the menu lock

Repeat the procedure above and set and (MENU LOCK) to OFF.

ZZ...

17

US

Technical Features

Power saving function (user sensor/power saving mode)

This monitor meets the power-saving guidelines set by VESA,

E

NERGY

S

TAR, and NUTEK. If the monitor is connected to a computer

or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically enter the power

saving mode. It automatically enters the low power consumption mode when the user sensor detects the absence of a user.

1 Low power consumption mode (user sensor)

When the user sensor in the monitor detects the absence of a user,

the monitor enters low power consumption mode after about 20

seconds. In low power consumption mode, the monitor is in a

power saving state and shuts off power to all circuitry (except for

that of the sensors) regardless of the setting of the computer.

The monitor returns to normal operation mode when the presence

of a user is detected by the user sensor.

When the monitor enters the power saving mode (as set according

to the computer’s settings), the power saving mode takes

precedence over the low power consumption mode. In this case,

the monitor stays in the power saving mode regardless of the

presence or absence of a user.

To return the monitor to normal operation mode, reset the

computer’s power saving mode.

Note

The user sensor detects the presence/absence of a user up to a distance of

approximately 60 cm from the screen surface. However, this distance may

vary depending on the user’s clothes or the brightness of the surrounding

area. If user detection fails due to the ambient conditions of the

surrounding area, set the user sensor to OFF. If your monitor does not

automatically return from low power consumption mode due to the failure

of the user sensor to detect the presence of a user, press the

1

(power)

switch twice to turn the monitor off and then on.

2 Power saving mode

DPMS defines three power saving states according to the state of

the sync signals supplied from the computer. This monitor’s

power consumption is input at approximately 3 W in all of these

states if the power saving function is set to ON.

When your computer enters in the power saving mode, the input

signal is cut and NO INPUT SIGNAL appears on the screen.

After a few seconds, the monitor enters power saving mode.

* “Sleep” and “deep sleep” are power saving modes defined by the

Environmental Protection Agency.

Note

The power saving function may not work normally if sync signals other

than those listed above are supplied. In such a case, set the power saving

function to OFF.

Power consumption state Power consumption AC power indicator 1 (power) indicator

normal operation

35

W green green

1 low power consumption mode

≤ 8

W green green and orange alternate

2 power saving mode

≤ 3

W orange orange

1 (power): off

≤ 3

Wred off

AC power: off 0 W off off

Power saving

state

Sync signal state

suspend (sleep)* horizontal: on / vertical: off

standby (sleep)* horizontal: off / vertical: on

active off (deep sleep)* horizontal: off / vertical: on

18

Automatic brightness adjustment function (light sensor)

This monitor is provided with a feature to automatically adjust the screen brightness according to the brightness of the surroundings. The

brightness of the backlight is set to the most appropriate level by setting the light sensor to ON. The default setting of the brightness of the

backlight is set to its maximum. When the light sensor setting is set to ON, the monitor adjusts the brightness of the backlight linearly from

its lower- to upper-limit values. When the user adjusts the backlight, the backlight brightness is automatically adjusted between the user

adjustment value and the upper- and lower-limit values.

Automatic picture quality adjustment function

When the monitor receives an input signal, it automatically

matches the signal to one of the factory preset modes stored in the

monitor’s memory to provide a high quality picture at the center

of the screen. (See Appendix for a list of the factory preset

modes.)

For input signals that do not match one of the factory preset

modes, the automatic picture quality adjustment function of this

monitor automatically adjusts the picture position, phase, and

pitch, and ensures that a clear picture appears on the screen for

any timing within the monitor’s frequency range (horizontal: 30 –

61 kHz, vertical: 50 – 85 Hz).

Consequently, the first time the monitor receives input signals

that do not match one of the factory preset modes, the monitor

may take a longer time than normal for displaying the picture on

the screen. This adjustment data is automatically stored in

memory so that next time, the monitor will function in the same

way as when the monitor receives the signals that match one of

the factory preset modes.

In all modes as above, if the picture is adjusted, the adjustment

data is stored as a user mode and automatically recalled whenever

the same input signal is received.

Note on the adjusting the phase

If the automatic picture quality adjustment function is activated, the

picture moves slightly whenever the monitor receives the input signal,

regardless of the stored adjustment.

Note

While the automatic picture quality adjustment function is activated, only

the

1

(power) switch, and INPUT button will operate.

User-specified

brightness value

Backlight brightness

Maximum

User adjustment value

Minimum

Automatic brightness adjustment

after user adjustment

Preset automatic adjustment

Brightness of surroundings

Brightness during

user adjustment

19

US

Troubleshooting

Before contacting technical support, refer to this section.

On-screen messages

If there is something wrong with the input signal, one of the

following messages appears on the screen. To solve the problem,

see “Trouble symptoms and remedies” on page 20.

If OUT OF SCAN RANGE appears on the screen

This indicates that the input signal is not supported by the

monitor’s specifications. Check the following items.

If “xx.x kHz/xx Hz” is displayed

This indicates that either the horizontal or vertical frequency

is not supported by the monitor’s specifications.

The figures indicate the horizontal and vertical frequencies of

the current input signal. The horizontal frequencies above

100 kHz and the vertical frequencies above 100 Hz are

represented by 99.9 kHz and 99 Hz, respectively.

If “RESOLUTION > XGA” is displayed

This indicates that the resolution is not supported by the

monitor’s specifications.

If NO INPUT SIGNAL appears on the screen

This indicates that no signal is input, or that no signal is input

from the currently selected connector.

INPUT:

This indicates the currently selected connector (INPUT: 1 or

INPUT: 2).

GO TO POWER SAVE

The monitor will enter the power saving mode after about 4

seconds from the message is displayed.

If CABLE DISCONNECTED appears on the screen

This indicates that the video signal cable has been disconnected

from the currently selected connector.

INPUT:

This indicates the currently selected connector (INPUT: 1 or

INPUT: 2).

GO TO POWER SAVE

The monitor will enter the power saving mode after about 4

seconds from the message is displayed.

OUT OF SCAN RANGE

xx . xkHz / xxHz

INFORMATION

NO INPUT SIGNAL

INPUT : 1

GO TO POWER SAVE

INFORMATION

CABLE DI SCONNECTED

INPUT : 1

GO TO POWER SAVE

INFORMATION

20

Trouble symptoms and remedies

If a problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual.

Use the self-diagnosis function (page 22) if the following recommendations do not resolve the problem.

Symptom Check these items

No picture

If the AC power indicator is not lit • Check that the power cord is properly connected.

If the AC power indicator is red • Check that the 1 (power) switch is in the “on” position.

If the 1 (power) indicator is not lit,

or if the 1 (power) indicator will not

light up when the 1 (power) switch

is pressed

• Check that the 1 (power) switch is in the “on” position.

• Check that the AC power switch is in the “on” position.

• Check that the system connecting cable is properly connected and all plugs are firmly

seated in their sockets (page 8).

If the 1 (power) indicator is green

or flashing orange

• Use the self-diagnostics function (page 22).

If the 1 (power) indicator is

alternating between green and

orange

• The monitor cannot return from low power consumption mode because the user sensor

fails to detect the presence of a user. Press the 1 (power) switch twice to turn the monitor

off and then on. If you set the user sensor to OFF, the monitor does not enter low power

consumption mode (page 16).

If CABLE DISCONNECTED

appears on the screen, or the AC

power indicator is flashing red

• Check that the video signal cable is properly connected and all plugs are firmly seated in

their sockets (page 8).

• Check that the video input connector’s pins are not bent or pushed in.

• A non-supplied video signal cable is connected. If you connect a non-supplied video

signal cable, CABLE DISCONNECTED appears on the screen before entering the power

saving mode. This is not a malfunction.

• Check that the system connecting cable is properly connected and all plugs are firmly

seated in their sockets (page 8).

• Press the AC power switch twice to turn the monitor off and then on.

If NO INPUT SIGNAL appears on

the screen, or the 1 (power)

indicator is orange

• Check that the video signal cable is properly connected and all plugs are firmly seated in

their sockets (page 8).

• Check that the input select setting is correct (page 10).

• Check that the video input connector’s pins are not bent or pushed in.

xProblems caused by the connected computer or other equipment

• The computer is in the power saving mode. Try pressing any key on the keyboard or

moving the mouse.

• Check that the computer’s power is “on.”

• Check that the graphic board is completely seated in the proper bus slot.

If OUT OF SCAN RANGE appears

on the screen

xProblems caused by the connected computer or other equipment

• Check that the video frequency range is within that specified for the monitor. If you

replaced an old monitor with this monitor, reconnect the old monitor and adjust the

frequency range to the following:

Horizontal: 30 – 61 kHz

Vertical frequency: 50 – 85 Hz (only XGA mode at 75 Hz)

If using Windows 95/98 • If you replaced an old monitor with this monitor, reconnect the old monitor and do the

following. Install the Windows Monitor Information Disk (page 9) and select this monitor

(“SDM-N50”) from among the Sony monitors in the Windows 95/98 monitor selection

screen.

If using a Macintosh system • Check and refer to the supplied “Notes for Macintosh users.”

La pagina sta caricando ...

Sony SDM-N50 Manuale del proprietario

Sony SDM-N50 Manuale del proprietario

in altre lingue

Documenti correlati