Copyright 2011 ZyXEL Communications Corporation
C
Box Contents
Overview
The PoE12-HP is a one-port power injector, designed for use with 10/
100/1000 BaseT Ethernet networks. The PoE12-HP injects DC power
through the unused twisted-wires of a standard 8-pin CAT 5 cable.
This increases flexibility in the positioning of a power over Ethernet
(PoE) enabled device by eliminating the need for a nearby power
source.
Key Features
• Complies IEEE802.3at and IEEE 802.3af.
• One RJ-45, 10/100/1000 Mbps PoE-enabled port.
• Ensures a constant power supply to a PoE-enabled device.
• Automatically detects if the connected device is PoE-enabled to
avoid sending power to a non-PoE device.
Connecting the PoE12-HP
Connect the PoE12-HP as follows.
1. The DATA port does not deliver power. Use an Ethernet cable to
connect the PoE12-HP’s DATA port to the LAN of an Ethernet
device (such as an Ethernet switch).
2. The PoE/DATA port sends power and Ethernet data to your PoE-
enabled device. Use a straight-through Ethernet cable to connect
the PoE/DATA port to your PoE-enabled device.
The maximum Ethernet cable length is 100m.
• One PoE12-HP • One User’s Guide • Wall-mounting
Accessory
• One Power Cord • One Warrenty Card
1
3
DATA
PoE/DATA
PoE-enabled
device
Ethernet device
1
2
3. Use the included power cord to connect the PoE12-HP’s power
socket to a power source (wall outlet or power strip).
•The PWR LED turns on green when the PoE12-HP is receiving
power.
LEDs
The following table describes the LEDs on the PoE12-HP.
Wall Mounting
Do the following to attach your PoE12-HP to a wall.
1. Screw the two screws provided with your PoE12-HP into the wall
106 mm apart. Use screws with 6 mm ~ 8 mm (0.24" ~ 0.31") wide
heads. Do not screw the screws all the way in to the wall; leave a
small gap between the head of the screw and the wall.
2. The gap must be big enough for the screw heads to slide into the
screw slots and the connection cables to run down the back of the
PoE12-HP.
Make sure the screws are securely fixed to the wall and strong
enough to hold the weight of the PoE12-HP with the connection
cables.
3. Align the holes on the back of the PoE12-HP with the screws on
the wall. Hang the PoE12-HP on the screws.
Troubleshooting
The PWR LED is off and/or power is not being supplied to my PoE-
enabled device.
• Check to see that the power cord is securely connected to the
PoE12-HP and an appropriate power source. Make sure the power
source is on and functioning properly.
• Refer to the Connecting the PoE12-HP section. Check that the
Ethernet cables are connected properly and that you are using the
correct type of Ethernet cable. Contact your local distributor if the
problem persists.
LED Color Status Description
PoE Green Blinking The PoE12-HP is detecting PoE-enabled device.
On PoE power is supplied.
PWR Green On The system is turned on.
Off The system is off or has failed.
The PoE12-HP should be wall-mounted
vertically with the power socket facing
upwards.
106mm
User’s Guide
PoE12-HP
802.3at PoE Injector
Version 1.00
Edition 1, 4/2011
ENGLISH
Packungsinhalt
Übersicht
Der PoE12-HP ist ein Power Injector mit einem Anschluss für die
Verwendung mit 10/100/1000 BaseT Ethernet-Netzwerken. Der
PoE12-HP-Anschluss leitet DC-Strom durch die nicht verwendeten
gedrehten Leitungen eines 8-poligen CAT 5-Standardkabels. Das
bietet mehr Flexibilität beim Aufstellen eines PoE-fähigen Geräts, da
dafür nun keine zusätzliche Stromquelle benötigt wird.
Die wichtigsten Leistungsmerkmale
• Entspricht IEEE802.3at und IEEE 802.3af.
• Ein PoE-fähiger RJ-45-Anschluss, 10/100/1000 Mbps.
• Stellt eine gleichmäßige Stromversorgung für ein PoE-fähiges Gerät
sicher.
• Erkennt automatisch, ob das angeschlossene Gerät PoE-fähig ist,
um die Stromversorgung eines nicht PoE-fähigen Geräts zu
vermeiden.
Anschließen des PoE12-HP
Schließen Sie den PoE12-HP entsprechend der folgenden
Beschreibung an.
1. Der DATA-Anschluss liefert keinen Strom. Schließen Sie ein
Ethernet-Kabel an den DATA-Anschluss des PoE12-HP und an
den LAN-Anschluss eines Ethernet-Geräts (z. B. eines Ethernet-
Switches) an.
2. Der Anschluss PoE/DATA leitet den Strom über das Ethernetkabel
zum PoE-fähigen Gerät. Verbinden Sie das PoE-fähige Gerät mit
einem direkten Ethernetkabel an den Anschluss PoE/DATA an.
Die maximale Lange des Ethernetkabels betragt 100m.
• Ein PoE12-HP • Ein Benutzerhandbuch • Wandmontage-
Zubehör
• Ein Netzkabel • Eine Garantiekarte
1
3
DATA
PoE/DATA
PoE aktiviert
Gerät
Ethernet-Gerät
1
2
3. Schließen Sie das mitgelieferte Stromkabel an den Netzanschluss
und an das Stromnetz an (Wandsteckdose oder
Steckdosenleiste).
•Die PWR-LED wird grun, sobald der Anschluss PoE12-HP mit
Strom versorgt.
LED-Anzeigen
In der folgenden Tabelle wird die Bedeutung der unterschiedlichen
LED-Anzeigen des PoE12-HP beschrieben.
Wandmontage
Führen Sie die nachfolgenden Schritte aus, um den PoE12-HP an
einer Wand zu montieren.
1. Schrauben Sie die zwei mit dem PoE12-HP mitgelieferten
Schrauben in einem Abstand von 106 mm in die Wand.
Verwenden Sie Schrauben mit 6 - 8 mm breiten Köpfen (0,24 -
0,31"). Drehen Sie die Schrauben nicht vollständig in die Wand.
Zwischen dem Kopf der Schrauben und der Wand sollte ein
kleiner Abstand bleiben.
2. Der Abstand muss so groß sein, dass Sie das den PoE12-HP,
dessen Schraublöcher sich an der Rückseite befinden, in den
Schraubköpfen einhängen können.
Stellen Sie sicher, dass die Schrauben sicher an der Wand
angebracht und stark genug sind, um das Gewicht des PoE12-
HP und der Anschlusskabel zu tragen.
3. Richten Sie die Löcher an der Rückseite des PoE12-HP an den
Schrauben in der Wand aus. Hängen Sie den PoE12-HP an die
Schrauben.
Problembeseitigung
Die PWR-LED leuchtet nicht und/oder das PoE-fähige Gerät wird
nicht mit Strom versorgt.
• Make sure the power source is on and functioning properly. Prüfen
Sie, ob das Netzkabel fest am PoE12-HP-Anschluss und an einer
geeigneten Stromquelle angeschlossen ist. Stellen Sie sicher, dass
die Stromquelle eingeschaltet ist und richtig funktioniert.
• Lesen Sie nach im Abschnitt Anschließen des PoE12-HP.
Prüfen Sie, ob der richtige Ethernetkabeltyp verwendet wurde
und ob sie richtig angeschlossen sind. Wenn das Problem
weiterhin bestehen bleibt, wenden Sie sich an einen
Vertragshändler in Ihrer Nähe.
LED Farbe Status Beschreibung
PoE Grün Blinkt Der PoE12-HP ermittelt ein PoE-fähiges Gerät.
Ein PoE-Stromversorgung vorhanden.
PWR Grün Ein Das System ist eingeschaltet.
Aus Das System ist ausgeschaltet oder ein Fehler ist
aufgetreten.
Der PoE12-HP sollte vertikal an einer
Wand montiert werden, und der
gerichtet sein.
106 mm
Stromanschluss sollte nach oben
Benutzerhandbuch
PoE12-HP
802.3at PoE Injector
Version 1.00
Ausgabe 1. 4/2011
DEUTSCH
Contenido de la caja
Vista general
El PoE12-HP es un inyector de potencia de un puerto, diseñado para
usarlo en redes Ethernet 10/100/1000 BaseT. El PoE inyecta
corriente DC a través de los cables trenzados no usados de un cable
estándar CAT 5 de 8 contactos. Esto aumenta la flexibilidad en el
posicionamiento de un dispositivo con corriente sobre Ethernet (PoE)
eliminando la necesidad de una fuente de alimentación cercana.
Características principales
• Cumple con IEEE802.3at y IEEE 802.3af.
• Un puerto RJ-45, 10/100/1000 Mbps con PoE activado.
• Asegura una fuente de corriente constante para dispositivos con
PoE.
• Detecta automáticamente si el dispositivo conectado tiene PoE para
evitar enviar corriente a dispositivos sin PoE.
Conectar el PoE12-HP
Conecte el PoE12-HP como sigue.
1. El puerto DATA no envía corriente. Utilice un cable Ethernet para
conectar el puerto DATA del PoE12-HP a la LAN de un dispositivo
Ethernet (como un switch Ethernet).
2. El puerto PoE/DATA envía corriente y Ethernet a su dispositivo
con PoE. Utilice un cable directo Ethernet para conectar el puerto
PoE/DATA a su dispositivo con PoE.
La longitud máxima del cable Ethernet es 100m.
• Un PoE12-HP • Una Guía del usuario • Accesorio para montaje
en la pared
• Un cable de corriente • Una Tarjeta de garantía
1
3
DATA
PoE/DATA
PoE activado
dispositivo
Dispositivo Ethernet
1
2
3. Utilice el cable de corriente incluido para conectar el zócalo de
corriente a la fuente de alimentación (toma de corriente o regleta).
•El LED PWR se enciende en verde cuando el PoE12-HP está
recibiendo energía.
LEDs
La tabla siguiente describe los LEDs del PoE12-HP.
Montaje en pared
Siga estos pasos para montar su PoE12-HP en una pared.
1. Atornille los dos tornillos incluidos con su PoE12-HP en la pared
con 106mm de separación. Use los tornillos con cabezas de 6mm
a 8mm (0,24" a 0,31") de ancho. No atornille los tornillos hasta el
fondo en la pared; deje un pequeño hueco entre la cabeza del
tornillo y la pared.
2. El hueco debe ser lo suficientemente grande para que las cabezas
de los tornillos puedan entrar en las ranuras de y los cables de
conexión quepan a través de la parte posterior del PoE12-HP.
Compruebe que los tornillos estén bien fijos en la pared y sean
lo suficientemente fuertes como para soportar el peso del
PoE12-HP con los cables de conexión.
3. Alinee los agujeros en la parte posterior del PoE12-HP con los
tornillos en la pared. Cuelgue el PoE12-HP en los tornillos.
Solución de problemas
El LED PWR está apagado y/o la corriente no llega a mi dispositivo
con PoE.
• Compruebe si el cable de alimentación está bien conectado al
PoE12-HP y a una fuente de alimentación apropiada. Compruebe si
la fuente de alimentación está encendida y si funciona
correctamente.
• Consulte la sección Conectar el PoE12-HP. Compruebe si los
cables Ethernet están bien conectados y si está utilizando el tipo
correcto de cable Ethernet. Contacte con su distribuidor local si el
problema persiste.
LED Color Estado Descripción
PoE Verde Parpadeando El PoE12-HP está detectando el dispositivo
con PoE activado.
Encendido Hay suministro de energía PoE.
PWR Verde Encendido El sistema está encendido.
Apagado El sistema está apagado o ha fallado.
El PoE12-HP debe montarse en la pared
verticalmente con el enchufe mirando
hacia arriba.
106mm
Guía del usuario
PoE12-HP
Inyector 802.3at PoE
Versión 1.00
Edición 1, 4/2011
ESPAÑOL
Contenu de l'emballage
Présentation
Le PoE12-HP est un injecteur d'alimentation simple port, conçu pour
une utilisation avec les réseaux Ethernet 10/100/1000 BaseT. Le PoE
injecte le courant CC à travers les fils torsadés non utilisés d'un câble
CAT 5 à 8 broches standard. Ceci augmente la flexibilité et le
positionnement d'un périphérique adapté Power over Ethernet (PoE)
en éliminant le besoin d'une source d'alimentation proche.
Caractéristiques principales
• Compatible IEEE802.3at et IEEE 802.3af.
• Un port RJ45, 10/100/1000 Mbps PoE.
• Assure une alimentation continue du périphérique PoE.
• Détecte automatiquement si le périphérique connecté est PoE pour
éviter d'alimenter un périphérique non-PoE.
Connexion du PoE12-HP
Connectez le PoE12-HP comme suit.
1. Le port DATA ne délivre pas d'alimentation. Utilisez un câble
Ethernet pour connecter le port DATA du PoE12-HP au LAN d'un
périphérique Ethernet (par exemple un switch Ethernet).
2. Le port PoE/DATA fournit l'alimentation et Ethernet à votre
périphérique adapté PoE. Utilisez un câble Ethernet droit pour
connecter le port PoE/DATA à votre périphérique adapté PoE.
La longueur maximum du cable Ethernet est de 100m.
• Un PoE12-HP • Un guide de l'utilisateur • Un support de fixation
murale
• Un cordon
d'alimentation
• Une carte de garantie
1
3
DATA
PoE/DATA
Périphérique PoE
Périphérique Ethernet
1
2
3. Utilisez le cordon d'alimentation fourni pour connecter la prise
d'alimentation à une source d'alimentation (prise murale ou une
prise multiple).
• La LED PWR devient verte quand le PoE12-HP est alimenté.
Voyants lumineux
Le tableau suivant décrit les voyants lumineux du PoE12-HP.
Fixation murale
Suivez les étapes pour fixer votre PoE12-HP à un mur.
1. Vissez les deux vis fournies avec votre PoE12-HP dans le mur à
106 mm l'une de l'autre. Utilisez des vis de 6mm à 8mm (0,24" à
0,31") à tête large. Ne vissez pas complètement les vis dans le
mur; laissez un petit espace entre la tête de la vis et le mur.
2. L’espace doit être assez grand pour permettre aux têtes de vis de
s'insérer dans les logements prévus et pour faire descendre les
câbles de connexion derrière le PoE12-HP.
Vérifiez que les vis sont correctement fixées au mur et assez
solides pour supporter le poids du PoE12-HP avec les câbles de
connexion.
3. Alignez les trous à l'arrière du PoE12-HP avec les vis sur le mur.
Accrochez le PoE12-HP sur les vis.
Dépannage
La LED PWR est éteinte et/ou l'alimentation n'est pas fournie à mon
périphérique adapté PoE.
• Vérifiez si le cordon d'alimentation est correctement connecté au
PoE12-HP et à une source d'alimentation appropriée. Vérifiez si la
source d'alimentation est allumée et fonctionne correctement.
• Reportez-vous à la section Connexion du PoE12-HP. Vérifiez que
les câbles Ethernet sont connectés correctement et que vous
utilisez le type de câble Ethernet correct. Contactez votre
distributeur local si le problème persiste.
DEL Couleur État Description
PoE Vert Clignotant Le PoE12-HP est en train de détecter le
périphérique PoE.
Activé L'alimentation du PoE est fournie.
PWR Vert Activé Le système est allumé.
Désactivé Le système est éteint ou défaillant.
Le PoE12-HP doit être fixé au mur
verticalement avec la prise de courant
106mm
orientée vers le haut.
Manuel de l'utilisateur
PoE12-HP
802.3at PoE Injector
Version 1.00
Édition 1, 4/2011
FRANÇAIS
Contenuto della confezione
Cenni generali
Il PoE12-HP è un iniettore di alimentazione a una porta, progettato
per essere utilizzato in reti Ethernet 10/100/1000 BaseT. El PoE
inyecta corriente DC a través de los cables trenzados no usados de
un cable estándar CAT 5 de 8 contactos. Esto aumenta la flexibilidad
en el posicionamiento de un dispositivo con corriente sobre Ethernet
(PoE) eliminando la necesidad de una fuente de alimentación
cercana.
Caratteristiche principali
• Conforme agli standard IEEE802.3at e IEEE 802.3af.
• Una porta RJ-45, porta PoE 10/100/1000 Mbps.
• Consente di alimentare in modo costante un dispositivo PoE.
• Rileva automaticamente se il dispositivo collegato è abilitato a PoE
al fine di evitare di inviare corrente ad un dispositivo non-PoE.
Collegamento del PoE12-HP
Effettuare i collegamenti del PoE12-HP nel modo seguente.
1. La porta DATA non trasmette elettricità. Utilizzare un cavo
Ethernet per collegare la porta DATA del PoE12-HP alla porta
LAN di un dispositivo Ethernet (come ad esempio uno switch
Ethernet).
2. La porta PoE/DATA invia elettricità e dati Ethernet al dispositivo
abilitato PoE. Utilizzare un cavo Ethernet passante diritto per
collegare la porta PoE/DATA al dispositivo abilitato PoE.
La lunghezza massima del cavo Ethernet e 100m.
• Una unità PoE12-HP • Una Guida dell'utente • Accessori per il
montaggio a parete
• Un cavo di
alimentazione
• Una scheda di garanzia
1
3
DATA
PoE/DATA
Dispositivo
PoE
Dispositivo Ethernet
1
2
3. Utilizzare il cavo di alimentazione in dotazione per collegare la
presa di alimentazione ad una sorgente di alimentazione (presa a
muro o ciabatta elettrica).
•Il LED PWR diventa di colore verde quando il PoE12-HP è
alimentato.
LED
Nella tabella seguente sono descritti i LED presenti sul PoE12-HP.
Montaggio a parete
Attenersi alla procedura seguente per fissare il PoE12-HP alla
parete.
1. Fissare le due viti fornite a corredo con il PoE12-HP nella parete,
a una distanza di 106mm. Usare viti con testa da 6 a 8mm (0,24" -
0,31"). Non avvitare completamente le viti nella parete, ma
lasciare un piccolo spazio tra la testa della vite e il muro.
2. Lo spazio deve essere abbastanza grande da consentire alle teste
delle viti di scorrere nelle apposite fessure e ai cavi di
connessione di scorrere lungo la parte posteriore del PoE12-HP.
Assicurarsi che le viti siano saldamente fissate alla parete e che
siano abbastanza robuste per sostenere il peso del PoE12-HP
con i cavi di collegamento.
3. Allineare i fori presso la parte posteriore di PoE12-HP con le viti
sulla parete. Appendere il PoE12-HP sulle viti.
Risoluzione dei problemi
Il LED PWR è spento e/o non viene fornita alimentazione al
dispositivo abilitato PoE.
• Controllare per verificare che il cavo di alimentazione sia collegato
correttamente al PoE12-HP e ad una adeguata sorgente di
alimentazione. Assicurarsi che la sorgente di alimentazione sia
attiva e funzioni correttamente.
• Fare riferimento alla sezione Collegamento del PoE12-HP.
Controllare che i cavi Ethernet siano collegati correttamente e che
venga usato il tipo corretto di cavo Ethernet. Se il problema persiste,
contattare il proprio distributore locale.
LED Colore Stato Descrizione
PoE Verde Lampeg
giante
Il PoE12-HP sta rilevando il dispositivo PoE.
Acceso È fornita alimentazione PoE.
PWR Verde Acceso Il sistema è acceso.
Spento Il sistema è spento o ha un guasto.
È preferibile montare il PoE12-HP a
elettrica dal lato superiore.
106mm
parete in senso verticale, con la presa
Guida dell'utente
PoE12-HP
Iniettore PoE 802.3at
Versione 1.00
Edizione 1, 4/2011
ITALIANO
:
PoE12-HP ,
Ethernet 10/ 100/1000 BaseT.
5-
. PoE12-HP
, PoE,
.
• IEEE802.3at IEEE 802.3af.
• 10/100/1000 Mbps RJ-45
PoE.
• PoE.
•
PoE
, .
PoE12-HP
PoE12-HP .
1.
DATA
. Ethernet
PoE12-HP
DATA
LAN
() Ethernet (, Ethernet ).
2.
PoE/DATA
, PoE.
"" Ethernet, ,
PoE,
PoE/DATA
.
• PoE12-HP •
•
• •
1
3
DATA
PoE/DATA
PoE
Ethernet
1
2
Ethernet 100 .
3.
( ).
• PWR PoE12-HP
.
PoE12-HP.
PoE12-HP .
1.
, PoE12-HP,
106 . 6
~ 8 (0.24" ~ 0.31"). ;
.
2. ,
PoE12-HP.
PoE12-HP
.
3. PoE12-HP
. PoE12-HP .
!
PWR
/
, PoE.
•
PoE12-HP
. .
•. PoE12-HP.
Ethernet
Ethernet. ,
ZyXEL
.
PoE PoE12-HP PoE.
PoE .
PWR
(
)
.
.
PoE12-HP
106
.
PoE12-HP
802.3at PoE
1.00
1, 4/2011
ฏխփ୲
ᄗᥦ
PoE12-HP ਢԫጟക墅ሽᕴ (power injector)Δറჸ 10/100/1000
BaseT Ԭ֜ጻሁૠࠌشۖૠΖ PoE12-HP ຘመآࠌشመऱᑑᄷ 8
൷ᆬ CAT 5 ীᠨᒵࣹԵऴੌሽΖຍױ༼Ԭ֜ጻሁࠎሽ (PoE) ᇘᆜ
ऱࡳۯᐘࢤΔլᏁᔢ༉ॵ२ऱሽᄭΖ
פ౨
• ฤٽ IEEE802.3at א֗ IEEE 802.3afΖ
• ԫଡ֭ག 10/100/1000 Mbps ႚᙁຒ৫ፖ PoE( Ԭ֜ጻሁࠎሽ ) פ౨
ऱ RJ-45 കΖ
• ᒔঅ PoE ᇘᆜሽᄭࠎᚨլၴឰΖ
• ۞೯ೠྒྷຑ൷ऱᇘᆜਢܡ֭ག PoEΔᝩ܍ಬሽॺ PoE ᇘᆜΖ
ຑ൷
PoE12-HP
PoE12-HP ຑ൷ֱڤڕՀΖ
1. DATA കլᄎႚᙁሽԺΖࠌشԬ֜ጻሁᒵല PoE12-HP ऱ DATA ക
ຑ۟Ԭ֜ጻሁᇘᆜऱ LAN( ࠏڕԬ֜ጻሁٌངᕴ )Ζ
2. PoE/DATA കലሽԺࡉԬ֜ጻሁႚಬࠩ PoE ᇘᆜΖࠌشԫኙԫԬ֜
ጻሁᒵല PoE/DATA കຑ൷ࠩ PoE ᇘᆜΖ
Ԭ֜ጻሁᒵ९৫່९
100m
Ζ
3. ࠌشᙟॵऱሽᄭᒵലሽᄭ༺ᑒຑ൷ࠩሽᄭ ( ᛥ૿༺ஆࢨ༺ஆิ )Ζ
• ᅝ PoE12-HP ൷گࠩሽᄭழΔPWR LED ਐقᗉᄎॽದጸۥΖ
• ԫ PoE12-HP • ԫءࠌش֫ם • ᕻٙ
• ԫයሽᄭᒵ • ԫ്অࡐ
1
3
DATA
PoE/DATA
PoE ᇘᆜ
Ԭ֜ጻሁᇘᆜ
1
2
LED
ਐقᗉ
אՀ।ᎅࣔ PoE12-HP Ղऱ LED ਐقᗉΖ.
ᕻ
ࠉᅃאՀޡᨏല PoE12-HP ࡐࡳڇᛥ૿ՂΖ
1. ലࠟឍ PoE12-HP ᙟॵऱᝅඝԵᛥփΔא 106 mm ၏ᠦሶၲΖᓮ
ࠌشᝅᙰऴஉڇ 6 mm ~ 8 mm (0.24" ~ 0.31") հၴऱᝅΖլ
ނᝅ٤ຝඝԵᛥխΔᝅᙰፖᛥ૿հၴႊఎԫ՛़ᎼΖ
2. ڼ़Ꮌؘႊߩאᨃᝅᙰ࣋ၞᝅᑒΔࠀᨃຑ൷ᨱᒵױൕ PoE12-
HP હ૿ࢮנΖ
ᒔᎁᝅբᒔኔࡐࡳڇᛥՂΔױ֭ᐶ
PoE12-HP
ࡉຑ൷ᨱᒵऱ٤ຝૹ
ၦΖ
3. ࠌ PoE12-HP હ૿ऱ֞ኙᏘᛥ૿ՂऱᝅΖല PoE12-HP ڇᝅ
ՂΖ
ጊᣄඈᇞ
PWR LED ਐقᗉዽᄰ֗ЯࢨሽԺآႚಬࠩ PoE ᇘᆜΖ
• ᛀီሽᄭᒵਢܡᒔኔຑ൷ࠩ PoE12-HP א֗ሽԺࠐᄭਢܡᔞᅝΖᒔ
ᎁሽᄭբၲඔሎ܂إൄΖ
• ᓮᔹຑ
ຑ൷
PoE12-HP ԫᆏΖᛀԬ֜ጻሁᒵਢܡຑ൷إᒔא֗ਢ
ܡࠌشإᒔऱԬ֜ጻሁᒵᣊীΖڕ࣠սڶംᠲΔᓮᅝچᆖᔭΖ
LED
ਐقᗉ
ᠱۥ णኪ ᎅࣔ
PoE
ጸۥ ೂᡩ PoE12-HP إڇೠྒྷ PoE ᇘᆜ
Ζ
ၲඔ ࠎᚨ PoE ሽᄭΖ
PWR
ጸۥ ၲඔ ߓอբၲඔ
Ζ
ᣂຨ ߓอբᣂຨࢨਚᎽΖ
PoE12-HP ᚨিऴᕻΔ
ࠀࠌሽᄭ༺ᑒཛՂ
Ζ
106mm
ࠌش֫ם
PoE12-HP
802.3at PoE
墅ሽᕴ
1.00 ठ
2011 ڣ 4 ִॣठ
᧯խ֮
Copyright 2011 ZyXEL Communications Corporation
C
Product Specifications
Safety Warnings
• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.
• Do NOT expose your device to dampness, dust or corrosive liquids.
• Do NOT store things on the device.
• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of
electric shock from lightning.
• Connect ONLY suitable accessories to the device.
• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high
voltage points or other risks. ONLY qualified service personnel should service or disassemble
this device. Please contact your vendor for further information.
• Place connecting cables carefully so that no one will step on them or stumble over them.
• Always disconnect all cables from this device before servicing or disassembling.
• Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply
voltage (for example, 110V AC in North America or 230V AC in Europe).
• Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product
where anyone can walk on the power adaptor or cord.
• Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.
• If the power adaptor or cord is damaged, remove it from the device and the power source.
• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.
• Do not use the device outside, and make sure all the connections are indoors. There is a remote
risk of electric shock from lightning.
• Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.
• Make sure that the cable system is grounded so as to provide some protection against voltage
surges.
• Make sure to connect the cables to the correct ports.
• Your product is marked with this symbol, which is known as the WEEE mark. WEEE
stands for Waste Electronics and Electrical Equipment. It means that used electrical
and electronic products should not be mixed with general waste. Used electrical
and electronic equipment should be treated separately.
Copyright
Copyright © 2011 by ZyXEL Communications Corporation.
The contents of this publication may not be reproduced in any part or as a whole,
transcribed, stored in a retrieval system, translated into any language, or transmitted in any
form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying,
manual, or otherwise, without the prior written permission of ZyXEL Communications
Corporation.
Published by ZyXEL Communications Corporation. All rights reserved.
Disclaimer
ZyXEL does not assume any liability arising out of the application or use of any products, or
software described herein. Neither does it convey any license under its patent rights nor the
patent rights of others. ZyXEL further reserves the right to make changes in any products
described herein without notice. This publication is subject to change without notice.
Certifications
Federal Communications Commission (FCC) Interference Statement
The device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operations.
This device has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This device generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this device does cause harmful interference to radio/television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
CE Mark Warning:
This is a class B product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Notices
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Viewing Certifications
Go to http://www.zyxel.com
.
Compatibility • IEEE802.3 10BASE-T
• IEEE802.3u 100BASE-TX
• IEEE802.3ab 1000BASE-T
• IEEE802.3af
• IEEE802.3at
Ports • One DATA port for connecting to the passive hub or switch
• One
PoE/DATA
port for connecting to the PoE-enabled device
LEDs 1 PoE (green) 1 PWR (green)
Power Input: 1100~240V, 50~60Hz
Power Rating 100~240VAC 50/60Hz 1.5A max.
Power Consumption 42.1W
Weight Dimensions 396g 155 (W) * 74 (D) * 36 (H) mm
Operating Environment Temperature: 0 ~ 50
o
C
Humidity: 10 to 95% (non-condensing)
Storage Environment Temperature: -40 ~ 70
o
C
EMI and Safety EN 60950-1, CSA international, FCC Part15 (Class B), CE
EMC (Class B), RoHS Level A
Select your product on the ZyXEL home page to go to that product's page.
Select the certification you wish to view from this page.
ZyXEL Limited Warranty
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects
in materials or workmanship for a period of up to two years from the date of purchase. During
the warranty period, and upon proof of purchase, should the product have indications of
failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or
replace the defective products or components without charge for either parts or labor, and to
whatever extent it shall deem necessary to restore the product or components to proper
operating condition. Any replacement will consist of a new or re-manufactured functionally
equivalent product of equal or higher value, and will be solely at the discretion of ZyXEL.
This warranty shall not apply if the product has been modified, misused, tampered with,
damaged by an act of God, or subjected to abnormal working conditions.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of the
purchaser. This warranty is in lieu of all other warranties, express or implied, including any
implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in
no event be held liable for indirect or consequential damages of any kind to the purchaser.
To obtain the services of this warranty, contact your vendor. You may also refer to the
warranty policy for the region in which you bought the device at http://www.zyxel.com/web/
support_warranty_info.php.
Registration
Register your product online to receive e-mail notices of firmware upgrades and information
at www.zyxel.com for global products, or at www.us.zyxel.com for North American products.
ENGLISH DEUTSCH
Green Product Declaration
RoHS Directive 2002/95/EC
Green Product Declaration
RoHS Directive 2002/95/EC
WEEE Directive 2002/96/EC
(WEEE: Waste Electrical and Electronic
Equipment)
2008/34/EC
WEEE Directive 2002/96/EC
(WEEE: Waste Electrical and Electronic
Equipment)
2008/34/EC
Declaration Signature:
Name/Title: Raymond Huang /
Quality & Customer Service
Division Assistant VP
Date (yyyy/mm/dd): 2011/1/24
Unterschrift des Erklärenden:
Name/Titel: Raymond Huang /
Quality & Customer Service
Division Assistant VP
Datum (JJJJ/MM/TT): 2011/1/24
ESPAÑOL FRANÇAIS
Declaración de Producto Ecológico
Directiva RoHS 2002/95/EC
Déclaration de Produit Green
Directive RoHS 2002/95/EC
Directiva REEE 2002/96/EC
(REEE : Residuos de Equipos Eléctricos y
Electrónicos)
2008/34/EC
Directive DEEE 2002/96/EC
(DEEE : Déchets des Equipements
Electriques et Electroniques)
2008/34/EC
Firma de declaración:
Nombre/Título: Raymond Huang
/ Quality & Customer Service
Division Assistant VP
Fecha (aaaa/mm/dd): 2011/1/24
Signature de la déclaration :
Nom/Titre : Raymond Huang /
Quality & Customer Service
Division Assistant VP
Date (aaaa/mm/jj) : 2011/1/24
ITALIANO NEDERLANDS
Dichiarazione Green Product
Direttiva RoHS 2002/95/CE
Productmilieuverklaring
RoHS-richtlijn 2002/95/EC
Direttiva RAEE 2002/96/CE
(RAEE: Rifiuti di Apparecchiature Elettriche
ed Elettroniche)
2008/34/EC
AEEA-richtlijn 2002/96/EC
(AEEA: Afgedankte Elektrische en
Elektronische Apparaten)
2008/34/EC
Firma dichiarazione:
Nome/titolo: Raymond Huang /
Quality & Customer Service
Division Assistant VP
Data (aaaa/mm/gg): 2011/1/24
Verklaringshandtekening:
Naam/titel: Raymond Huang /
Quality & Customer Service
Division Assistant VP
Datum(jjjj/mm/dd): 2011/1/24
SVENSKA
Miljödeklaration
RoHS Direktiv 2002/95/EC
WEEE Direktiv 2002/96/EC
(WEEE: hantering av elektriskt och
elektroniskt avfall)
2008/34/EC
Deklaration undertecknad av:
Namn/Titel: Raymond Huang /
Quality & Customer Service
Division Assistant VP
Datum (åååå/mm/dd): 2011/1/24
-
1
-
2
in altre lingue
- English: ZyXEL PoE12-HP Owner's manual
- français: ZyXEL PoE12-HP Le manuel du propriétaire
- español: ZyXEL PoE12-HP El manual del propietario
- Deutsch: ZyXEL PoE12-HP Bedienungsanleitung